The path for the GPIO devices needs to be '\_SB', not '\SB'. Fix
the path so that it references the system bus.
BUG=b:72121803
Change-Id: I7c6c38ecea0f8f95ff52b3390f92c5b7e79bcd6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23501
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SPI controller on stoneyridge apparently has a large fifo
and an alternate method for programming the controller. The
fifo is directly accessible as well as the rx and tx pointer
in addition to the execute bit. Remove the unneeded #defines
and program the host controller with the above changes in mind.
In addition, add debug hooks to the driver so one can dump the
state of the controller when in operation.
The time it took to read 4KiB of flash in the elog driver went
from 20593 microseconds to 5693 microseconds on cdx03/kahlee.
BUG=b:65485690
Change-Id: Ie7ea9d18cef5511686700ad9b2b9fdfeb6d5685b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23493
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The spi flash host controller has a dedicated register for the
opcode. Therefore, indicate to the spi subsystem that the opcode
size should not be taken into account when determining maximum
payload size in spi_crop_chunk(). This allows the full use of
the fifo when doing transfers.
BUG=b:65485690
Change-Id: Iab27a69ca72fd02bc443f0673983f3b22ffca0f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23492
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
spi_crop_chunk() currently supports deducting the command length
when determining maximum payload size in a transaction. Add support
for deducting just the opcode part of the command by replacing
deduct_cmd_len field to generic flags field. The two enums supported
drive the logic within spi_crop_chunk():
SPI_CNTRLR_DEDUCT_CMD_LEN
SPI_CNTRLR_DEDUCT_OPCODE_LEN
All existing users of deduct_cmd_len were converted to using the
flags field.
BUG=b:65485690
Change-Id: I771fba684f0ed76ffdc8573aa10f775070edc691
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23491
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some panels need to transfer initial code, and some of them will be
over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi
dsi transfer function to support it.
Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Harcuvar is the board name, Denverton is the SoC. So macros in files under
soc/ should be named after the SoC not the board.
Change-Id: I1c7d5b93fba386b8e9bd86cf599508e642e21a75
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shine Liu <shine.liu@intel.com>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The scratch registers in northbridge used for storing the top of
cacheable memory are volatile. Use the BiosRam storage in the FCH
instead.
TEST=Suspend and resume Kahlee with complete S3 patch stack
BUG=b:69614064
Change-Id: Ieb3cfd173c70bf899a6391d62d1df87b38485f30
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Both early platform information reporting in bootblock and common code
CPU driver will add support for cannonlake D0 stepping processor.
BUG=None
TEST=Boot up system with D0 stepping CPU installed, check serial log
that can display as D0 stepping.
Change-Id: I76ee974ee027100d7853a110f95b1601987492e4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change the BiosRam read/write functions to use the fixed MMIO range at
0xfed80500. This is faster than two accesses per byte when using I/O
0xcd4/0xcd5.
Note that BiosRam may only be accessed byte-by-byte. It does not decode
normally.
Change-Id: I9d8baf2bd5d9d48a87bddfb6a0b86e292a8fdf7d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23436
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The following two patches were independent, but they were
merged together. However, the first one changed the API
that the second was originally was written against. Fix build.
b94a2750 (i2c/designware: reduce API complication for bus config)
13101a7b (soc/amd/stoneyridge: Add I2C devicetree support)
BUG=b:72121803
Change-Id: I3678a8f414572dd2227c42ce5585daf6bc933df5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23445
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The TSC rate is empirically swinging during early boot. That
leaves timestamps and udelay()s to not be correct. To rectify this
stop using TSC for all of these time sources. Instead use the
performance TSC which is at a fixed 100MHz clock. That provides
stable time sources and legit timestamps.
BUG=b:72378235,b:72170796
Change-Id: Ia2693c415c557aac687bcb48ee69358ea1c53d67
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This commit adds device name to ACPI name bindings for various entries
in the devicetree.
BUG=b:72121803
Change-Id: I5564e4a7e56fdd1bc9f34497bdb78383093a2ba3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
3rdparty/blobs was updated to move northbridge/amd/00670F00 contents into
soc/amd/stoneyridge. Now soc/amd/stoneyridge/Kconfig needs to be updated
to use VBIOS.bin new location.
BUG=b:70785272
TEST=Update 3rdparty/blobs master branch, try to build kahlee. It should
fail. Update soc/amd/stoneyridge/Kconfig, try to build kahlee again, it
should work (need to rebuild .config first).
CQ-DEPEND=CL:881709
Change-Id: I8cb9874eedc4a5d41d42b3f727c6d3cb9b920b5a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Rename the device ID macros as per the skylake PCH H external design
specification.
Change-Id: I4e80d41380dc1973d02bc69ac32aad5c4741a976
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23381
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This moves the call to pch_enable_lpc() from romstage to bootblock.
In other words, it happens earlier in the boot process. Turns out, we
need this to talk to the EC to determine if we're in recovery mode or
not.
BUG=b:69011806
TEST=boots to linux
Change-Id: I899bf343d705fe19a2978917bc88990495ebb5a3
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The FSP 2.0 Memory_Info_HOB for KBL is not sending
"MemoryType" value as what is required for SMBIOS Table
according to SMBIOS Spec. Thus, converting the value
retrieved from FSP HOB to the correct value.
This change will not be required for upcoming SOCs since
FSP have fixed this issue in its next platforms and thus it
will take care and send the correct value in "MemoryType"
field based on SMBIOS spec. Thus this conversion from coreboot
will not be required in the next platfoms. "MemoryType" value
can be directly passed to dimm_info_fill() function.
BUG=none
BRANCH=none
TEST=Tested in Soraka, and getting the value as 0x1D for
LPDDR3 memory. dmidecode (latest version 3.1) Command Type 17
will also show correct information. Currently, it was showing
"Unknown".
Change-Id: I75d6cca464680a88bf836e25bf5440a9cdbc738e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/23384
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CAR APIs already exist to deal with proper type useage.
Don't open code things that already exist.
BUG=b:65485690
Change-Id: I09593401513f6060a30cf5c02c94d14afbe8f4fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
The TSC has been observed to be ticking at a non-constant rate
in early boot. The root cause is still not known, but this
misbehavior necessitates an alternative monotonic timer source.
Use the perf TSC which ticks at 100 MHz. This also means the
timestamp table is not accurate as well. Root cause of TSC rate
instability needs to be resolved in order to fix that.
BUG=b:72170796
Change-Id: Ie052169868a9d9f25f8cc0ce8dd8251b560e671f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
For the internal eMMC to be used by non-chrome for installation,
the CARD device and _RMV methods are required. Without these,
other OSes does not show the eMMC as a valid installation target.
TEST= boot CNL-RVP with Tiano payload and install Windows 10
to the internal eMMC drive.
Change-Id: Icfdccd88bc113d97c2fabf4c63d8d772737a6057
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Solution: To do an additional config read to the SD controller
after the controller has been power gated (put to D3)
Change-Id: Ia2438c767332b0e2d413c71b06b052bf9ab4a96c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Solution: To do an additional config read to the eMMC controller
after the controller has been power gated (put to D3)
Change-Id: Ieac939c9108e84ba6c7c26b1a49aaf829d8456b7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add new function sb_program_gpio to be called after AGESA init_reset
and some point within ramstage. For AGESA init_reset, change
amd/stoneyridge/bootblock/bootblock.c function bootblock_soc_init
(add the function after the call to AGESA function).
BUG=b:64140392
TEST=Build kahlee, grunt, gardenia.
Change-Id: I38da26cd1e20617958a6b17d55b7d7c08b8a0230
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22987
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
PC10 is a necessary condition for S0ix entry. With the current C-state limits,
CPU fails to enter PC10 during S0ix. C-state Latency control limits
have to be tuned to new values for PC10 entry.
Change-Id: I0f5227f9c3c10c5a9e335ab118eb0ec185445374
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/23220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CONFIG_STONEYRIDGE_SATA_MODE is compared against "magical numbers".
Because actual literals are in AGESA.h and adding agesa_headers.h to
southbridge.h causes compile errors, move comparison code from southbridge.h
to southbridge.c (where they are actually used). Replace these numbers
with actual literals.
BUG=b:71754828
TEST=Build kahlee.
Change-Id: I711473bf492d5ceca026ccd112c2c389a23bdbf9
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
At AGESA AmdInitReset, SATA enable and IDE enable (elements of
FCH_RESET_INTERFACE) are programmed twice (before calling AGESA
for AmdInitReset and from said AGESA function call out), using
different functions with different results. The first would result
in TRUE/FALSE, the second set would result in TRUE/TRUE. Use the
functions of the second set within the first set, and remove them
from the second set.
BUG=b:71754828
TEST=Build kahlle without the change, boot and record output. Rebuild
kahlee with the change, boot and record output. Compare both outputs,
the should be no change except in timing.
Change-Id: I326fcc8801542aa7feef286d02abdfe63354cdd0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove the BiosRam read and write functions that were brought over from
the hudson source. The functionality will be superseded later with new
general-purpose functions.
Change-Id: Ib80c66b838fdbdd388a392b4fedaac36bf0bbb0c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22725
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The internal FCH contains 256 bytes of "BiosRam" that maintains its
state until RSMRST# is asserted or standby power is lost. Add functions
to support read and write operations.
Change-Id: I2ddf58a63e69b2775de9a8163534b13dad2ea2fe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Relocate the acpi_get_sleep_type() function out of the southbridge
ramstage file. This will make it more convenient for using elsewhere.
Change-Id: Id7ba709bb867fb00ed6c7fa7526de087a3b9b3ca
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The cbmem location holding the heap will be used to store additional
information in subsequent patches. Remove the static designation from
agesa_heap_base.
Change-Id: Ic607432fd6500ef69b5d47793896cf12a699d8b7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22721
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A subsequent patch will use GetHeapBase() in more files than
heapmanager.c. Convert it to a format more similar to existing
coreboot source.
Change-Id: I8362af849fc9d7cb1b8a93113e8d78dcac51c20a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In 6c747068 "amd/stoneyridge: Put AGESA heap into cbmem" the AGESA
heap was moved completely into cbmem. This was a departure from the
"late cbmem init" method of adding it late in post, then storing the
S3 volatile data to the region. Remove the hardcoded base address
that was missed in that commit.
To prepare for S3 support, split the region into subregions for
heap, AGESA's S3 volatile storage, and an MTRR save area.
BUG=b:69614064
Change-Id: I06c137f56516f3a04091d1191cd657a0aa07320b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Remove the original spi.c file that writes S3 NV data to flash in a
proprietary format. The s3 folder is retained to facilitate new
development.
Change-Id: I1b5fe8e854c3d2dd71506c2acd6ff73e4b86d7d4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
PMC controller gets hidden during FSP Silicon initialization
using sideband interface on CNP-PCH. Hence unable to reserve
PMC IO resources during PCI enumeration process. This causes
hang issue on non-chrome platform with CNP-PCH due to ABASE
corruption.
This patch ensures PMC IO resource (ABASE) is getting reserved
(IO address 0x1800-0x1900) and ACPI base is not overwritten by
other devices.
TEST=ABASE range is reserved along with LPC IO range during PCI
enumeration.
PCI: 00:1f.0 resource base 1800 size 100 align 0 gran 0 limit 0
flags c0000100 index 20
Change-Id: I1fbc4339ae11058fb3daedf4ffedda1904fa52ec
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures common block has option to reserve IO resources
based on SOC requirements. Also add pch_lpc_ prefix to maintain
same function nomenclature across all intel common block.
Change-Id: Ic00af688104bcea1aff06be6cbb20208a60e5f1d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Furquan Shaikh