With the default CPU voltage (0.8v), CPU frequency should be 1417Mhz at
most. We have to raise CPU frequency to 1989MHz after increasing CPU
voltage to 1.05v in romstage.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I4c3e0fa27ccda8e0efe422b6ab503a1efb1697e9
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
NEED_VB20_INTERNALS should always be specified when peeking
into vboot internal data structures.
BUG=b:124141368, chromium:956474
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5a47a28350fd5a68efeff0d06ca150c1ae145412
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable the GBB flag forcing manual recovery now that we can read
the manual recovery from H1.
Enable the GBB flag to skip EC software sync, since images built
from coreboot.org do not include the EC binaries by default.
Change-Id: I0e1d6304e3e29eda68c7b807cf0774275c37d710
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
If the Intel IGD device pci 02.0 is disabled or undefined in
the device tree, then internal graphics pre-allocated memory
and GFX-VT MMIO memory for virtualization won`t be allocated
in the SoC address space.
Thus, patch resolves the FSP-S hang problem on Skylake/ Kaby
Lake processors when the IGD device is disabled. This should
provide to run FSP 2.0-based coreboot on these CPUs families
without integrated graphics card.
The following boards were used for testing:
- Asrock H110M-DVS board (desktop i5-6600) & NVIDIA GTX 1060
as external GPU.
Virtualization and GFX 3D acceleration with nouveau driver
still works well (tested on VirtualBox 5.1.38 with Ubuntu
18.04.1 as guest and host OS)
- Intel KBL-R U RVP board (mobile i5-8350u) without GFX.
Payload: tianocore edk2-stable201811-216-g51be9d0.
Change-Id: Id7a0cba582d83e3fe7e8d20342ee219cdd369a53
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32467
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Clear the GPI Interrupt Status & Enable registers to prevent any
interrupt storms due to GPI.
BUG=b:130593883
BRANCH=octopus
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: Ia3b9d3bf08472219348e20b53bae470c589039fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support to reset the GPI Interrupt Status & Enable registers so that
the system does not experience any interrupt storm from a GPI when it
comes out of one of the sleep states.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up. Ensure that the system boots fine to ChromeOS.
Change-Id: I99f36d88cbab8bb75f12ab1a4d06437f837841cb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the offset information for GPI interrupt status and enable register
in the pad_community structure. Populate the concerned information for
individual SoCs. This offset information is required to clear the
interrupt configuration during the bootup.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the interrupt configuration are cleared during bootup.
Ensured that the system boots to ChromeOS.
Change-Id: I8af877a734e8d49b700d720b736da8764985a8f8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We only grep'ed for "ACPI Warning" resulting in an actual more severe
"ACPI Error" being ignored.
Change-Id: I9cec8a388f5558b1ffc383cc2fc69405252cbb37
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The ACPI code of LPE device is included regardless of the
availability of the LPE controller.
Linux remains requesting the status of device LPEA even if
this device is disabled.
Include ACPI LPE controller code at Braswell mainboards with
LPE enabled.
BUG=N/A
TEST=Linux 4.17+ on Portwell PQ7-M107
Change-Id: Ic8acf9ea9e9b0ba9b272e20beb2023b7a4716a73
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Intel's DQ_DQS_RComp_Info_Utility generates data for 6 entries. MRC will
return errors if we don't have all 6 entries in the map.
BRANCH=none
BUG=b:131103736
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I20a768de0e4440d7dde7b717794c4e2d0c62819c
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Changes includes:
- enable TPM1 + add entry in devicetree
- configure LPC IO to make IPMI work + add entry in devicetree
- introduce DSDT and SMBIOS entries for IPMI to make it detectable
by ipmi_si driver
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: Ia975643064075f1f861f4ead6f24ed71f345ea04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Remapping Hardware Status Affinity (RHSA) structure is applicable for
platforms supporting non-uniform memory. An ACPI Name-space Device
Declaration (ANDD) structure uniquely represents an ACPI name-space
enumerated device capable of issuing DMA requests in the platform.
Add RHSA and ANDD structures support for DMAR table generation.
BUG=b:130351429
TEST=Image built and booted to kernel
Change-Id: I042925a7c03831061870d9bca03f11bf25aeb3e7
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The IRQ tables don't support this path, so we shouldn't report presence
of the legacy PICs. As the _PIC method is optional and we ignore the
passed parameter anyway, drop it.
Change-Id: I51301a600e16f74fde00fdcb4595e1f47a52e207
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
This patch revises the AC/DC loadline settings because some major
layout changes between proto and evt boards.
BUG=b:130740639
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and boot to the OS.
Change-Id: Iea12c621e7fab427a0de8f43f0290bf01d0c5a09
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
The `printram` function only expands to a value only in debug builds.
This isn't done in default builds.
Change-Id: Ic88c4cc730ae2d0d0718c7f71260cd2b45a3ddcd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update submodule pointer to pull in newly-updated Braswell FSP.
Adjust FSP_FD_PATH for soc/cannonlake due to filename case change.
Change-Id: I02ee0d32fd4c04cd4971eff20fc5a7de3f9b07ec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635f ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FIT support takes more heap memory than most coreboot payloads.
Change-Id: Id17f25e94d97e937b0e9a9cee3dd1a8aef1d525d
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If override tree does not have any device, then the chip info
structure in it cannot be associated with the correct device and ends
up being added as a standalone chip info structure without any device
actually using it. This change prevents this condition by throwing an
error during compilation.
BUG=b:130342895
Change-Id: I7b8bb6b3228030a465976ca32ce8ef63f41365dd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tristan Shieh