For boards with cimx/sb800, mainboards defined only empty
stubs. Reset functionality is handled as BiosCallout.
For amd/inagua, the defined function was actually initial
GPIO programming.
For cimx/sb700, function had prototypes but no callers.
For cimx/sb900, everything was commented out already.
Change-Id: I936feb4fc41d903078620c919a733bb9f39c3efb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Vendorcode expects some DRAM controller registers to
be writable, but they are actually locked after soft
resets if C6 states are enabled.
Without the workaround, raminit fails on soft resets.
Change-Id: I6b9e275e11b2907d026c13341334983a4d9c8889
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's too critical to ignore when sending the message on
SMBus fails, so allow for a fair amount of retries.
Failure here causes watchdog to do hard reset later.
Move it out of mainboard.c as we need to call this
early in romstage while we are debugging.
Change-Id: I1006b079269d6dd44de630db7a5694124af2f974
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
NOTE: Some code was currently left behind that may be
required for certain type of board reboots. A followup
patch will address this.
Change-Id: I3c1258b4e4dcf6fd04f57f5ab59cb1572a7d1fa3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
SSFG was meant to be used as a mask to enable sleep states
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
State _S3 is now set conditionally if HAVE_ACPI_RESUME=y.
For pi/hudson this had been fixed already preprocessor.
Note that all boards had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
States _S1 and _S2 still appear enabled in ASL/AML
but may not actually work.
TEST: 'cat /sys/power/state' and notice choice 'mem' was
removed from the list of available sleep states.
Change-Id: I27d616871c1771f0c87d8fba23d4ce1569607765
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
A decision has been made that boards with LATE_CBMEM_INIT
will be dropped from coreboot master starting with next
release scheduled for October 2017.
As existing implementation of CAR teardown in AGESA can only
do either EARLY_CBMEM_INIT or ACPI S3 support, choose the former.
ACPI S3 support may be brought back at a later date for
these platforms but that requires fair amount of work fixing
the MTRR issues causing low-memory corruptions.
Change-Id: I5d21cf6cbe02ded67566d37651c2062b436739a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
We define AGESA_LEGACY as an implementation of mainboard
that has its romstage main completely under mainboard/
directory. We have learnt from other platforms this approach
has several downsides when it comes to making platform-wide
improvements.
We start by creating per-family romstage.c file, which
boards will gradually take into use by removing the
AGESA_LEGACY Kconfig option we here apply to all of them.
Change-Id: Id01931e185a023039a60af16a678de9966db8d65
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18619
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
These definitions do not require AGESA.h include,
and we will eventually remove agesawrapper.h files.
Change-Id: I1b5b78409828aaf2616e177bb54a054960c3869f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18588
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This file is only static defines.
Change-Id: Id50a0eba1ce240df36da9bd6b2f39a263fa613df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18585
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Vendorcode always does PCI MMCONF access once it is
enabled via MSR.
In coreboot proper, we don't give opportunity to make
pci_read/write calls before PCI MMCONF is enabled via MSR.
This happens early in romstage amd_initmmio() for all cores.
Change-Id: If31bc0a67b480bcc1d955632f413f5cdeec51a54
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
File buildOpts.c is a can of worms, pull platform memory
configuration in to OemCustomize.c. This array should be
assigned at runtime instead of linking a modified defaults
table.
Change-Id: I73d9d3fbc165e6c10472e105576d7c40820eaa6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are other things besides PCIe port configuration that
require board specific hooks.
Change-Id: I0923651487b9ed5f6f7569ce08e02d993fa5f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Store (HPBA, HPBA) had no effect. Rename one of HPBA to avoid shadowing.
Change-Id: I54bfa7bcb3e05c28fe8a257825af56527dbf663e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13622
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The newer versions of IASL are unhappy when an operator
has the same object as both source and destination.
The warning can be completely disabled with a command
line argument, but in general, I'd really rather not
just disable warnings.
The bits in this register are write 1 to clear, so reading and
writing the same register is what we want to do. Instead, store
it in a temporary register then write it in a second operation.
Fixes warning:
dsdt.aml 1396: Store(PWST, PWST)
Warning 3023 - ^ Duplicate value in list
(Source is the same as Target)
Change-Id: I52d73d4431db237be83016d67cd397f31b53d9c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Not all the paths through the _OSC method returned a value. According
to the ACPI spec (5.0 & 6.0), bit 2 needs to be set for an unrecognized
GUID.
Fixes warnings for both platforms:
dsdt.aml 1143: Method(_OSC,4)
Warning 3115 - ^ Not all control paths return a value (_OSC)
dsdt.aml 1143: Method(_OSC,4)
Warning 3107 - ^ Reserved method must return a value
(Buffer required for _OSC)
Change-Id: Ibaf27c5244b1242b4fc1de474c371f54f930dcb6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12530
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We've actually got more warnings now than when I first tested IASL
warnings as errors. Because of this, I'm adding it with the option
to have it disabled, in hopes that things won't get any worse as we
work on fixing the IASL warnings that are currently in the codebase.
- Enable IASL warnings as errors
- Disable warnings as errors in mainboards that currently have warnings.
- Print a really obnoxious message on those platforms when they build.
***** WARNING: IASL warnings as errors is disabled! *****
***** Please fix the ASL for this platform. *****
Change-Id: If0da0ac709bd8c0e8e2dbd3a498fe6ecb5500a81
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
don't use non-volatile pointers for MMIO access
Change-Id: I9f38012a806e43f2535265f1d25537c59b53904e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12081
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Same comments were already removed for the latest board, the amd/lamar.
Change-Id: Ie244f838409c567c11f7444c9cf17de72e49dbb0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10283
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
These tables are not referenced anywhere, thus all
comments about adjustments are void.
Also drop stub AgesaReadSpd that is all commented out.
Change-Id: I12233ea0dc4baaf36a75f359c52cc59c9b6dad79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10143
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We do not allow platforms to mess around with memory layout.
Change-Id: I316ff522c8833fa3b7ad20f2c5a9cae21f4174d8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On x86, change the type of the address parameter in
read8()/read16/read32()/write8()/write16()/write32() to be a
pointer, instead of unsigned long.
Change-Id: Ic26dd8a72d82828b69be3c04944710681b7bd330
Signed-off-by: Kevin Paul Herbert <kph@meraki.net>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/7784
Tested-by: build bot (Jenkins)
These comments are left over and are not relevent in the coreboot
code, but created a new section titled "Release Content" in the
doxygen documentation produced by the coreboot code. In an effort
to clean up the output, I'm removing these doxygen comments.
Change-Id: I4d7be3313a2ab6c140b4f3afe70dffc4abba7bca
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8069
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fix system include paths to be consistent. Chipset support is
part of the Coreboot 'system' and hence 'non-local' (i.e., in
the same directory or context). One possible product of this, is
to perhaps allow future work to do pre-compiled headers (PCH) on
the buildbot for faster build times. However, this currently just
makes mainboard's consistent.
Change-Id: I2f3fd8a3d7864926461c960ca619bff635d7dea5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8085
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Remove PeiServices param for OemInitEarly - it doesn't exist in the
function.
Change-Id: I338aeb4128126f6e541815dc09bf8d23678081c8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8073
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
- Move @def BIOS_SIZE description to the next line
- SB_GEN2 changed to SB_GPP_GEN2
- Move the SIO_HWM_BASE_ADDRESS description to the next line
Change-Id: Ia3496b0108484f557627304553461932a100dfa5
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/8071
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
We should potentially provide an OEM platform hook to manipulate parameters
around any entry point to AGESA. Use structure for such ops to avoid weak
functions and lots of empty function stubs.
Change-Id: I99bf7de8a1e2f183399d2216520a45d0c24fd64c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7824
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
It does not really matter if we continue or return after a failed
assertion, system configuration is invalid anyway.
Change-Id: I5ba47ee3fd6c5ff97b9229f8bfc9db08873b08ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7823
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Not part of wrapper to AGESA, but workaround for enable_resources().
Also remove remains of comments in non-fam14 wrappers.
Change-Id: I2526821ca283feb6a506b602b86f817f8b03b341
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7816
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
These are not wrappers for AGESA as they do not enter vendorcode at all.
We expect most of the added fixme.c file to be written without use of AMDLIB.h
and parts relocated as northbridge enable_resources().
Change-Id: Iba6d59e2a7672349208e9a65fcd2cb1094ab7d50
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7815
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Enabling MMCONF PCI-e configuration access should be done before
console_init(). This will likely move further to bootblock one day.
Change-Id: I20c93fe6e79ef7e7981b2f1cd3c6b446feea0f4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7163
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
NOTE: For fam12 and fam14 ASSERT() is defined empty so execution may
fall through critical failures.
Change-Id: Ifef65d749d340f1df3a43b5fcb38c4315ef944e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7154
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
There are no reasons to not load ramstage @ 0x100000.
Boards with HAVE_ACPI_RESUME enabled have performance penalty in using
excessive RAMTOP. For these boards, this change releases 11 MiB of RAM from CBMEM allocation to OS.
Change-Id: Ib71995aba5e9332d0ec1626b3eb3b4ef6a506d1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7094
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
As was done for the reference boards in:
cd30951 mainboard/amd: De-ASCIIartify reference boards
Change-Id: Ie34aa5269388b771daa6934f8aff0314ac6778d5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6290
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
The only remaining purpose for get_bus_conf() was to fill in obscure
bus_sb800 (etc.) arrays containing partial PCI bus enumeration. Complete
enumeration is available in devicetree and PCI configuration space so
discard these arrays.
Change-Id: I733115940afba3a50c58aedb9a04ecf5082b1234
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6360
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Previously MP table contained PCI_INT entries for PCI bus behind bridge
0:14.4 even if said PCI bridge function was disabled.
Remove these as invalid, indeterminate bus number could cause conflicts.
PCI_INT entries with bus_sb800[2], bus_hudson[2] and bus_yangtze[2]
were invalid as there is no PCI bridge hardware on device 0:14.0.
Remove these as invalid, indeterminate bus number could cause conflicts.
Change-Id: Ie6a3807f64c8651cf9f732612e1aa7f376a3134f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6358
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
MP table should be complete with IRQ routing information even
when we have ACPI tables.
Change-Id: Ieeaed442aea6217f4477b7ac7e06a1926eec8996
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6361
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Integrated PCI devices in southbridge silicon have static BDFs,
no need to have variables to store the parent bus or an offset
with constant zero.
Change-Id: I37d3794d36b5e5775da9215574ddc199696646d0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6333
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Only ever used as lvalue (except when incrementing) so this global
is unused.
Change-Id: I616721f937eb0bfdb28f356284efd70f99ccd2dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6330
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Found using coccinelle.
Change-Id: I406de6cfe25d3b471dbb6f98d9c62addae008de3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6195
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Only ever used as lvalue, so no point creating the array.
Change-Id: I6699dfae9377a895e9bc4a52579d00ddcfa60a9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6277
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Followup deals further with Fam15 case. For unknown reasons calls
were commented out for amd/dinar and they remain that way.
Change-Id: Ie0a25fbb6f5378019fbf0f19a02acf024d79817e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6237
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Implement logging just once to have uniform output.
Change-Id: I8db694a3bf6b1af459bdf98f7acb99edf4dd07f7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6180
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
AGESA correctly uses the enum AGESA_STATUS type whereas boards use a
mess of UINT32 typecasts.
Also no need to shout VOID. We are not that careful on changing
all cases of VOID->void or whitespace issues as these files will
get merged with follow-ups.
Change-Id: I16ccfcc73cda6b917c7ff5fd42ee2cd04e7dc0dd
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6182
Tested-by: build bot (Jenkins)
Instead of calling get_bus_conf() three times from write_tables()
and executing it once, just make one call before entering write_tables().
Change-Id: I818e37128cb0fb5eaded3c1e00b6b146c1267647
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6133
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
NOTE: The procedure is moved across a collected timestamp
TS_WRITE_TABLES, so the delay of SPI erase/write will be accounted
for in an earlier entry in cbmem -t output.
Change-Id: I0f082e7af1769c8d7d03cdd51fdb5dacbf3402b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6132
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
This adds use of BROKEN_CAR_MIGRATE to include CBMEM symbols for the
build of romstage also for boards without HAVE_ACPI_RESUME.
These symbols got exposed as the use of preprocessor directives was
reduced.
We expect the linker to do a fair job and optimize away function
bodies that are on unreachable execution paths.
Change-Id: Ibf5181d3eecb87ce647abe0be01072594b05aa5f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6067
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Use one common implementation for all AGESA platforms.
Change-Id: I410f8e0a9c75445882d67659cde00004eb7ad6b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6084
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
CONFIG_SIO_PORT is not used anywhere and should not be here any way.
Change-Id: I39eb2d668f1da9f89b7ff6eb219af1a48cb29232
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6044
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Try to 'standardize' the otherwise peculiar method naming to be somewhat
more in-line with other ACPI implementations. This makes it easier to
compare with vendor DSDT dumps for example.
Change-Id: I5ba54f7361796669ac0cab7ff91e7de43b22e846
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5888
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Use the following command to fix all occurences.
$ git grep -l approriate | xargs sed -i 's/approriate/appropriate/g'
Change-Id: I4cbba972bb445c2407ef2e63ffb3068fc948f1c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5987
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Rewrite smsc/smscsuperio romstage component to be more consistent and
provide header there-by removing #include's of early_serial.c's in
mainboard's.
Change-Id: I572e0c76422f09d4de88935a36c0a59e5350e6e0
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5915
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is x86 "standard" 0xcf9 reset mechanism.
Change-Id: Ieb48290b21a7cb1425881fdd65c794e96da0248f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5680
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These boards return with AGESA_UNSUPPORTED, while other boards return
AGESA_SUCCESS here when there is no hardware for external reset signalling.
Change-Id: I5aed211b1812888af55a691cfbfa8d7b5aff91bc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5679
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Most of the callouts are not specific to board or even family.
Start new file with default callouts doing nothing and returning
either AGESA_SUCCESS or AGESA_UNSUPPORTED.
Also add callout for returning empty IdsIdData. This feature is
not used and could be easily overriden at board-level at later time.
Change-Id: I65dbcdd80dddc89d47669ebe62c22caa63792f5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5678
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We should configure i8254/i8259 down in to the southbridge rather than
romstage of every AGESA/CIMx board much like Intel boards do.
Change-Id: Id7c4f0baa0819d52aef9b0ee03c20d0fa16b9352
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5669
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Lines with 'select SERIAL_CPU_INIT' where redundant with the
default being yes. Since there is no 'unselect SERIAL_CPU_INIT'
possibility, invert the default and rename option.
This squelches Kconfig warnings about unmet dependencies.
Change-Id: Iae546c56006278489ebae10f2daa627af48abe94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5700
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Heap allocation begins with BIOS_HEAP_MANAGER, no need to clear
the fields individually.
Change-Id: Ia1af84bd09d1edf8f72223752557d44a96dec6e1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5659
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Backported from fam15tn and fam16kb.
This also implements GetHeapBase() to satisfy some requirements
of HAVE_ACPI_RESUME for the following boards:
amd/inagua
amd/south_station
amd/union_station
asrock/e350m1
Change-Id: I488d063d4eabf4bf45bcbabd1e8f13b88b2ef401
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5658
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Backported from fam15tn and fam16kb.
Change-Id: I868352b32ff56a8386c615ab1a9f59e7e875292e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5657
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In amd/{persimmon,inagua} and derived boards avoid using AGESA
reimplementation of memcpy as following the reasoning in:
e2f3bfc jetway/nf81-t56n-lf: Use std memset/memcpy func over AGESA
Change-Id: I943b46103c3bf1c5fd88b25e9f9595b9adfcafeb
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5625
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Dumping the ACPI tables in this way has limited use, is not likely to be
used and is poorly implemented. There are much more sophisticated tools
available on Linux for debugging ACPI as such this code is outside the
scope of coreboots 'bring up the hardware only' philosophy.
A more generic implemention could be done with hexdump() in coreboot
proper following on from this cleanup.
Change-Id: Ifd3bfb76338609d18fcf7158d3c9a6d7c06c8847
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5530
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Not used with AGESA vendorcode.
Change-Id: Ic9a0513641bf76d748bb106675bccc33c7abe21e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5520
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Not used with AGESA vendorcode.
Change-Id: Ie99abf5bcffd740e2e7ed6d78937ab32935ef214
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5519
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Not all boards which use the AMD cimx/sb800 southbridge have IDE.
However, the southbridge's asl included an 'ide.asl' file which had to
be present in $(mainboard_dir)/acpi.
Address this issue by including ide.asl only in boards which have IDE,
and remove it from all other cimx/sb800 boards.
Change-Id: I57fcb4db9f85234b05ae1705ef81a576c478cee6
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5460
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Clean up vendor code from hard coded #define if-def chain with a
pre-processor shift and subtract.
Change-Id: Ibce34ab576d7db8586a6ec8f9b2460268e0e1878
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/4811
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
board_info.txt is a file to be used by board-status to add
some useful info to the generated table like flash chip type.
This series is autogenerated from wiki page Supported_Motherboards.
Change-Id: Ie2bda900713ef4883134477163320936c84c34f5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4701
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This change allows Kconfig options ROM_SIZE and CBFS_SIZE to be
set with values that are not power of 2. The region programmed
as WB cacheable will include all of ROM_SIZE.
Side-effects to consider:
Memory region below flash may be tagged WRPROT cacheable. As an
example, with ROM_SIZE of 12 MB, CACHE_ROM_SIZE would be 16 MB.
Since this can overlap CAR, we add an explicit test and fail
on compile should this happen. To work around this problem, one
needs to use CACHE_ROM_SIZE_OVERRIDE in the mainboard Kconfig and
define a smaller region for WB cache.
With this change flash regions outside CBFS are also tagged WRPROT
cacheable. This covers IFD and ME and sections ChromeOS may use.
Change-Id: I5e577900ff7e91606bef6d80033caaed721ce4bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4625
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
This config was for AMD K8 only.
Change-Id: Ic1ce60041fef6ddee2dae0e3559fb78f088740af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4556
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
A late for loop may reference over the current array allocation
and corrupt an unrelated global variable. As a quick fix bumb the
size of the array allocation uniformly to 6.
Change-Id: Ib067fdf077e091d13e32cc3a8e4a0b713d19bcc2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
... and drop the wrapper on ARMv7
Change-Id: If3ffe953cee9e61d4dcbb38f4e5e2ca74b628ccc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3639
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are no files to build left under AMD nortbridge/x/root_complex
directories. For some cases, even the Kconfig file was no longer sourced.
Remove all such references and empty files.
For devicetree.cb treat component paths with "/root_complex" in them valid
even when the directory does not exists. This is because AMD boards us this
dummy chip component as the root node in their devicetree.cb.
The generated devicetree file static.c remains unchanged.
Change-Id: I9278ebb50a83cebbf149b06afb5669899a8e4d0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3434
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
In commit Rudolf Marek discovered, that it is not uniformly written. As
»ASL names are not case-sensitive and will be converted to upper case.« [2]
this change does not have any functional change.
The following command was used to create this patch.
$ git grep -l 'package()' src/mainboard | xargs sed -i 's,package(),Package(),'
[1] http://review.coreboot.org/#/c/3318/
[2] http://www.acpi.info/spec40a.htm
(18.2.1 ASL Names)
Change-Id: I1784dbc50936a1ef9d4376209a3c324ef1fb85cf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3516
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Change `sizeof(type) * n`, where n is the number of array
elements, to `sizeof(variable)` to directly get the size of the
variable (struct, array). Determining the size by counting array
elements is error prone and unnecessary.
Rudolf Marek’s patch »ASUS F2A85-M: Correct and clean up PCIe
config« [1] contains the same change and is ported over. In
the commit message Rudolf makes the following comment.
»Not sure why the copy is needed instead of direct reference.
Maybe it has something to do with CAR?«
Testing on the ASRock E350M1, no regressions were noticed.
[1] http://review.coreboot.org/#/c/3194/
Change-Id: I123031b3819a10c9c85577fdca96c70d9c992e87
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3248
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
In `PlatformGnbPcie.c` AGESA functions are used to reserve memory
space to save the PCIe configuration to. This is the
With the following definitions in `AGESA.h`
$ more src/vendorcode/amd/agesa/f14/AGESA.h
[…]
/// PCIe port descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in complex
*/
IN PCIe_ENGINE_DATA EngineData; ///< Engine data
IN PCIe_PORT_DATA Port; ///< PCIe port specific configuration info
} PCIe_PORT_DESCRIPTOR;
/// DDI descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in complex
*/
IN PCIe_ENGINE_DATA EngineData; ///< Engine data
IN PCIe_DDI_DATA Ddi; ///< DDI port specific configuration info
} PCIe_DDI_DESCRIPTOR;
/// PCIe Complex descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in topology
*/
IN UINT32 SocketId; ///< Socket Id
IN PCIe_PORT_DESCRIPTOR *PciePortList; ///< Pointer to array of PCIe port descriptors or NULL (Last element of array must be terminated with DESCRIPTOR_TERMINATE_LIST).
IN PCIe_DDI_DESCRIPTOR *DdiLinkList; ///< Pointer to array DDI link descriptors (Last element of array must be terminated with DESCRIPTOR_TERMINATE_LIST).
IN VOID *Reserved; ///< Reserved for future use
} PCIe_COMPLEX_DESCRIPTOR;
[…]
memory has to be reserved for the `PCIe_COMPLEX_DESCRIPTOR` and,
as two struct members are pointers to arrays with elements of type
`PCIe_PORT_DESCRIPTOR` and `PCIe_DDI_DESCRIPTOR`, space for these
times the number of array elements have to be reserved:
a + b * 5 + c * 2.
sizeof(PCIe_COMPLEX_DESCRIPTOR)
+ sizeof(PCIe_PORT_DESCRIPTOR) * 5
+ sizeof(PCIe_DDI_DESCRIPTOR) * 2;
But for whatever reason parentheses were put in there making this
calculation incorrect and reserving too much memory.
(a + b * 5 + c) * 2
So, remove the parentheses to reserve the exact amount of memory
needed.
The ASRock E350M1 still boots with these changes. No changes were
observed as expected.
Rudolf Marek made this change as part of his patch »ASUS F2A85-M:
Correct and clean up PCIe config« [1]. Factor this hunk out as it
affects all AMD Brazos and Trinity based boards.
[1] http://review.coreboot.org/#/c/3194/
Change-Id: I32e8c8a3dfc5e87eb119eb17719d612e57e0817a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3239
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Apply the following commit to all AMD boards.
commit 935850e082
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon May 6 16:16:03 2013 -0700
asrock/e350m1: reduce default stack size
The stack used on the ASRock E350M1 is significantly less than
what we currently set (64k per core). In fact, we use about half
of the default stack size (4k) on core 0 and even less on non
BSP cores [1]:
$ grep stack coreboot_without_patch_but_monotonic_timer.log
CPU1: stack_base 002a0000, stack_end 002afff8
CPU1: stack: 002a0000 - 002b0000, lowest used address 002afda8, stack used: 600 bytes
CPU0: stack: 002b0000 - 002c0000, lowest used address 002bf75c, stack used: 2212 bytes
[…]
Reviewed-on: http://review.coreboot.org/3209
Please note that AGESA seems to define bigger stack sizes. But
these seem to be too much too.
$ git grep STACK_SIZE src/vendorcode/amd
[…]
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define BSP_STACK_SIZE 16384
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define CORE0_STACK_SIZE 16384
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define CORE1_STACK_SIZE 4096
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: BSP_STACK_SIZE,
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: CORE0_STACK_SIZE,
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: CORE1_STACK_SIZE,
[…]
The following command was used to create the patch.
$ git grep -l STACK_SIZE src/mainboard/ | xargs sed -i '/STACK_SIZE/,+3d'
Change-Id: I36b95b7a6f190b64d0639fc036ce2fb0253f3fa1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3217
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since this parameter is not used anymore, drop it from
all calls to copy_and_run()
Change-Id: Ifba25aff4b448c1511e26313fe35007335aa7f7a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
