hardware, rather than always on at full speed. Set temperature treshold values
to safe defaults, rather than the not-so-safe power-on defaults.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2674 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=0, 1 million outb():s are used
for timer calibration, which takes about one second.
All EPIA-M boards have timer2 so we use it to boot faster.
Only some EPIA boards have the Nehemiah CPU with timer2 so we default to IO
calibration but add the TSC options so that they can be set in Config.lb.
src/mainboard/via/epia*/reset.c is dead code (entire file within #if 0) so we
set HAVE_HARD_RESET=0 for both boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2659 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
problems with the asi/mb_5bmlp (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2644 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
minor changes, to bring them up to par. It also should remove (but might
just clean out) the irq_tables.c from both boards, because they were
just copied from Via Epia to begin with, and weren't usable. As far as I
can tell, these are the only changes needed to the targets for now,
aside from fixups to reset.c when the time comes. Both have been build
tested, but not checked on hardware since I don't have it. I have left
Uwe as the copyright holder since the only changes I've made are trivial.
Signed-off-by: Corey Osgood <corey_osgood@verizon.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2642 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the IGEL Winnet III thin client.
It boots a Linux kernel, but there are some problems. The login
prompt is never reached, it simply hangs at some point.
One possible reason is the IRQ table, which needs fixing.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2641 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the 5c register in the southbridge so that interrupts are routed
correctly.
With this patch, ethernet works quite well.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
adds a symbol to the model_lx/cache_as_ram.inc, and modifies some
files in the mainboard directory. This patch has been tested but there
is a remaining problem which I am tracking down. Expect one more patch
to "get it all working".
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2638 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-acking as this is pretty trivial. I tested both a normal build
and an abuild-run, and nothing breaks.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2635 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Geode changes.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2632 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
based on the Geode LX processor. The Norwich is the canonical
Geode reference, and will server as a good basis for other
Geode based platforms.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2629 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as that is not RAM but used for other stuff.
First try at PCI init added to src/mainboard/tyan/s1846/Config.lb.
Use a real payload (FILO) per default now.
Note: this cannot boot a payload, yet, but it gets a lot further now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2623 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Comment out code which currently doesn't compile. Needs fixing later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Drop AMD prototype mainboards that were for internal testing &
validation use only.
Note: These boards could never be purchased. No reasons to worry.
Questions welcome via private mail.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2609 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
abuild with a payload. Trivial
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2608 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
artecgroup/dbe61
Add CONFIG_COMPRESSED_PAYLOAD_NRV2B to Options.lb since it's used in
Config.lb.
Change default for CONFIG_PCI_ROM_RUN to 1 so VGA ROM can run.
technologic/ts5300
Removed CONFIG_CONSOLE_VGA, the embedded board has no VGA without the
development addon card anyways.
Changes to target Config.lb so it actually builds.
Signed-off-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2607 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* going back to old board specific dsdt for agami aruma.
This is hopefully dropped again some day, but until then
here's a working solution.
* Some minor Agami specific changes.
* drop obsolete bringup workaround hyperclocking.diff
* increase image size again, x86emu wants it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2606 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Drop empty file (0 bytes) northbridge/amd/amdk8/cpu_rev.c
and references to it.
* move config option decision to preprocessor instead of code
since config options can not change during runtime
* slightly more verbose output in built_opt_tbl.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's not fully working, among other things because the Intel
440BX northbridge isn't working, yet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2580 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty trivial, as it was correct in the original non-CAR code.
Suddently, CAR works nicely.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2572 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It does the ROM_STREAM -> PAYLOAD rename that afaik was done after
Yinghai sent his work to legal, so it is required to get that code
building.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2561 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2557 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Nvidia l1_2pvv
* Gigabyte m57sli
* Supermicro h8dmr
* Tyan s2912 -- with HTX
The boards will currently _not_ compile, two further patches
from Yinghai Lu are still missing. Please be patient :)
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2554 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
most people.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2545 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Luis Correia <luis.f.correia@gmail.com>). The code is loosely based on
the Eaglelion 5bcm mainboard.
Warning: this is work in progress!
As of now, it does boot with serial console only (no vga), and two ethernet
cards work sometimes. This has to do with the IRQ assignments, which are a
complete mess. USB is now apparently working, but I can't make any device
to be recognized.
The PCI slot is still unusable due to the IRQ thing.
Audio, other serial ports, irda, floppy and paralell port support is
unknown aka untested yet.
(closes#32)
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2508 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pmtools packages of upcoming SUSE 10.2, too, so the problem will
go away. (new package installed on linuxbios.org, too)
See also
http://www.linuxbios.org/pipermail/linuxbios/2006-September/015968.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2498 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and leaving enough room for a real payload (not /dev/null)
This is a wonderful example why "uses" sucks.
* add Config-abuild.lb for those boards that dont build with
the default settings and a real payload:
arima/hdama, amd/quartet, amd/serengeti_cheetah, ibm/e326
* if lzma is installed and a real payload is used, try compressing
it.
* fix a small bug in "abuild --help"
This patch is acked by me because its due to infrastructural changes only.
Flames welcome.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2496 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same format for all CHIP_NAME() entries in LinuxBIOS (Closes#20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
long time and I could not get into the tracker.
These are patches to enable ms9185 support. Abuild passes.
Signed-off-by: bxshi <bxshi@msik.com.cn>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2486 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Richard Smith <smithbone@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2483 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the E7520 and E7525 directories respectively.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2477 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and (hopefully) the correct canonical name of the vendor and board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2476 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the src/superio/NSC directory to src/superio/nsc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2472 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
me fix this before committing first.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2469 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
another commit is following
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2468 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add devices for the lx and artecgroup/dbe61
point artecgroup at cs5536_lx as it is so different.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Carl-Daniel Hailfinger
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2413 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
amd gx2 north -- don't set anything in the north, it conflicts with vsa
settings. So we have our own pci_set_resources that is essentially a
no-op -- just calls the kids.
olpc rev_a config -- DISABLE the compressed rom stream. This SHOULD NOT
have been set -- it is untested and caused real trouble.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* src/cpu/amd/model_lx/model_lx_init.c
L2 cache initialization removed (moved to northbridge.c)
* src/include/cpu/amd/lxdef.h
more checked values
* src/northbridge/amd/lx/northbridge.c
L2 cache initialization added
cpubug() commented out
* src/northbridge/amd/lx/raminit.c
empty function sdram_set_registers() is in use, don't remove
* src/mainboard/artecgroup/dbe61/Config.lb
irqmap changes
* src/mainboard/artecgroup/dbe61/irq_tables.c
tentative changes to irq table (currently not in use)
* src/mainboard/artecgroup/dbe61/mainboard.c
irq assigned manually to NIC
* src/mainboard/artecgroup/dbe61/Options.lb
gcc 4.0 is OK
* targets/artecgroup/dbe61/Config.lb
64K for VSA is OK at moment
Signed-off-by: Indrek Kruusa <indrek.kruusa@artecdesign.ee>
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
