There is no datasheet available for this SuperIO, but dumping all
possible registers on a Dell Optiplex GX520 resulted in data that was
similar to other supported chips. Data also matches what is set in the
BIOS, e.g. the parallel and serial ports' addresses.
Change-Id: I768e4b5ec1e73c53e1a2355e0a0657b7a5ccbb89
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch creates _PRT entires for each PCIE root port devices.
TEST=Able to see PCIE wake device in cat /proc/acpi/wake list
Change-Id: I183c89c92139e15e0bfc39620710dbdc6597b351
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Legacy PME are enabled by default in FSP-S UPD. This policy sets
PME Interrupt Enable (PIE) bit of RCTL register to trigger interrupt
generation when RSTS.PS state has changed (either due to 0->1 transition
or due to this bit being set with RSTS.PS already set). Due to this
interrupt generation, system wakes from sleep immediately it enters.
This patch overrides root port legacy pme upd policy from coreboot to
ensure no false SCI is triggerd when system is in S3/S0ix state.
BUG=b:113083354
BRANCH=none
TEST=Able to make S3 resume using wake on wifi connect/disconnect usecase
without any failure.
Change-Id: I779fac711eeeed65ea379fad1cc400052d8a00eb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some payloads don't depend on their supported platforms, which makes
them visible in menuconfig even if they are not supported (yet).
Change-Id: Ia1ec0f0ca0b6521d0c024500c67326337f3d744f
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The SCH3112, SCH3116 and SCH5127 were lacking a pin dump. Since their
datasheets are available, add their pin dumps.
The SCH3112, SCH3114 and SCH3116 are almost identical, they only differ
in the number of serial ports. Some values in the SCH3114 dump were
inaccurate, that has been fixed as well.
Datasheets used:
- SCH311X: DS00001872A
- SCH5127: DS00002081A
Change-Id: Ic985526be9b09e0452eaf883904dfaf709b7e907
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Setting default PSPP setting to BalancedLow was causing audio
playback issue in most of the units. With BalancedLow either there
was no sound or noise on playback.
Switching to BalancedHigh as default option.
BUG=b:116553085, b:112020107
TEST=Test playback and hear proper audio.
Change-Id: Ibf64d7b8e58e60ce931ddc85f11b135708cdb1ee
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28967
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch fixes KW issue due to pointer being NULL and will be dereferenced
Change-Id: Iedb59daf5f448e31c0097873a086e4d08cd4a979
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 3 for DVT.
BUG=b:115697578
TEST=verified it in Bobba EVT board which rework ram id.
Change-Id: I0fb457d8772f5038e5d90188d7682956ddfad46b
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28891
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It exposes an interface that is as generic as possible, so payloads
and/or kernels can use it for their data.
Change-Id: I9553922f9dfa60b9d4b3576973ad4b84d3fe2fb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/25182
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Wifi wake register is incorrectly set in devicetree.
Set wifi wake to its correct wake source, GPE0_DW2_01.
BUG=b:117330593
TEST='emerge-nocturne coreboot chromeos-bootimage', flash nocture,
connect wifi to a hotspot, suspend device, echo freeze >
/sys/power/state, and then shutdown the hotspot and verify device
wakes.
Change-Id: Iafa865ca79d33541d7f47b69d2fb209e7f9c98af
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28938
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The WAKE# signal has moved to LAN_WAKE, so WAKE# is now
floating and must be disabled. This change disables WAKE#.
BUG=b:117284700
TEST=none
Change-Id: I1c25e4ba28cd2b8807cd155d47c29c0d3ee9e8a5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* Convert PNG to JPG and reduce image quality.
* Mark flash IC and USB serial connector.
* Mark SPI programming header.
* Add programming header pinout.
Change-Id: Ica5958545ed23573a0d48dfa422ad1a822d06b47
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
* Add Makefile dependency to source file
* Add argument support
* Add help support
* Print usage on wrong arguments
* Add support for parsing VBT binary file
* Add support for parsing PCI Option ROM
* Add support for writing VBT binary file
* Add support for patching PCI Option ROM
* Keep support for accessing legacy VGA area Option ROM
* Keep support for dumping VBT contents to stdout
Allows to extract VBT, analyse VBT and patch PCI Option ROMs as needed.
The required arguments have been changed:
./intelvbttool --<SOURCECMD> [filename] --<DESTCMD> [filename]
SOURCECMD set the VBT source. Supported:
inlegacy : Legacy BIOS area at phys. memory 0xc0000
invbt : Read raw Intel VBT file
inoprom : Read VBT from Intel Option ROM file
DESTCMD set the VBT destination. Supported:
outdump : Print VBT in human readable form
outvbt : Write raw Intel VBT file
patchoprom: Patch existing Intel Option ROM
Any combination of SOURCECMD and DESTCMD is possible.
Change-Id: I8cbde042c7f5632f36648419becd23e248ba6f76
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
SiFive's website was reorganized, which broke our links to PDF files.
Update these links to the current ones, obtained by browsing
https://sifive.com/documentation/.
Change-Id: I312de84bf12abb0789bdd971c40033f1e4ea0dd1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
coreboot does not set up virtual memory anymore.
Change-Id: I231af07b2988e8362d1cdd606ce889fb31136ff1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
RISC-V is not a project of the University of California, Berkeley,
anymore; it stands on its own feet now.
Remove the "UCB" component from the RISC-V mainboards in the "emulation"
directory, and don't set MAINBOARD_VENDOR to UCB, either.
Change-Id: I301d9d0091a714e62375052e5af06a9197876688
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to make the macro name consistent for all PAD_CFG1_IOSSTATE_*
macros, this change uses lower case x for *RXD*. It helps avoid
confusion when using the macros.
Change-Id: I6b1ce259ed184bcf8224dff334fcf0a0289f1788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All ampton boards should have the DRAM info configured in CBI and so
DRAM_PART_NUM_ALWAYS_IN_CBI is already selected for ampton. This
change gets rid of the redundant minimum board id value for Ampton.
BUG=b:117071184
Change-Id: I59f60b8c5aa34b55b8e473c06cc49ea7ae284d62
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fleex does not have any device on I2C0 and hence this change disables
I2C0 device (16.0) in devicetree and gets rid of the I2C tuning
parameters for I2C0.
BUG=b:115600671
Change-Id: Ib799eae05b667cee2272bbd37f0ca44b7cec66cd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change uses the generic device driver to provide DMIC properties
in ACPI table to the OS driver.
BUG=b:112888584
Change-Id: I239f571bc29f02793f017a4713b5af03b23cfa3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28797
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support in generic device driver to add properties to
DSD table. This driver can be used by all generic devices that do not
need any special handling other than simply adding device properties
to be used by OS.
BUG=b:112888584
Change-Id: I0ca6614f1ef322397618676bbf6da898bef18990
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change sets scan_bus operation for HDA to scan_static_bus to
allow enumeration of static devices under HDA.
BUG=b:112888584
TEST=Verified that devices added under HDA get enumerated on Nocturne.
Change-Id: I20759c2b702b2f107f0913e7ce92a82c6070ddc4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Config option SOC_INTEL_COMMON_BLOCK_HDA is currently used for
initialization of HDA codecs only. This prevents adding of any static
devices under the HDA device node. However, there can be boards which
want to add devices under HDA node (e.g. nocturne that wants to
provide DMIC properties to OS) without performing any codec
initialization using the HDA. This change:
1. Adds a new config option SOC_INTEL_COMMON_BLOCK_HDA_VERB that can
be set explicitly by the boards that want to perform codec
initialization.
2. Uses newly added config option is used to guard the initialization
functions for the codec. Rest of the device operations can still be
used by all the other boards without having to use HDA codec
initialization.
3. Selects the newly added option SOC_INTEL_COMMON_BLOCK_HDA_VERB in
kblrvp which is the only board enabling HDA codec initialization
using common block code.
4. Selects original config SOC_INTEL_COMMON_BLOCK_HDA for skylake SoC.
Above changes need to be bundled and pushed in as a single change in
order to avoid breaking existing users.
BUG=b:112888584
Change-Id: Ie6f39c13a801833b283120a2d4b6f6175688999c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Uniformize the Yes/No in the tables, expand the internal programming
section and explain how to patch a defective flash descriptor.
Change-Id: I972bb8948c29ce0eba46daa92ce6b6052db7b063
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch removes assert() and checks if the dev is NULL with "if"
condition only.
Found-by: klockwork
Change-Id: Icd2c8490c8bda14ecd752437d463a7110fe40aea
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/28888
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Need to tune I2C bus 0/6/7 clock frequency under the 400KHz for
digitizer, touchpad, and touchscreen.
Bug=b:117126484
TEST=flash coreboot to the DUT and measure I2C bus 0/6/7 clock
frequency whether can <400KHz
Change-Id: Icb9592c688b864a21efd4963a4463845dfaa06fb
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28907
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This includes the SplitFspBin.py script.
Change-Id: I6323a7a1a2bd9b5e11c0b21e5ea991a3fbd3daac
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The extra firmware is not part of upstream kernel.
Fixes build error if the firmware is not present.
Change-Id: Ifbcb0bb0e2edf3aa260b40dfa339812019f9f0b3
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The W25Q128J is a QSPI flash chip, without ~HOLD and ~WP.
Add the device id to make coreboot boot from it.
Change-Id: I623fdf7d7e30eb28259bec6294785ad873f1f503
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Since `#if 1` is rather useless, and the code inside it is just several
`printk(BIOS_SPEW)`, using `if (console_log_level(BIOS_SPEW))` instead
seems more reasonable.
Change-Id: I93dcab3db958480626fea6d99ab5289ebff04e8f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Nautilus-LTE sku shows abnormal reset symptom at high temperature chamber
test, but the root cause is unclear.
Experimentally, setting SlowSlewRate IA/GT/SA to 1/2 improves this abnormal
reset issue, so we would apply it until find root cause of this issue.
BUG=b:117130599
BRANCH=poppy
TEST=Built and passed on reliability test with modified coreboot
Change-Id: I7fa0041989113097e3b283dbcf4ca2a73629fe54
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28785
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds the ACPI controls for power sequencing the touchscreen.
The initial setting is to keep the touchscreen powered off and in
reset. When linux is ready to talk to the touchscreen, it powers it
on and releases reset via ACPI.
BUG=b:110286344
TEST=verified touchscreen is functional in chromeos
Change-Id: I58c42a8f09342cfe54f82ef0e6cd8ea72a5140dc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28869
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the step of setting the SATA controller to S0 as the system is
entering S3. This had been duplicated from AMD's FchCarrizo.asl file,
but upon closer inspection, the conditions for this step to run cannot
be met. This does not affect Grunt's behavior, as the SATA controller
is disabled.
TEST=Suspend and resume Grunt
BUG=b:77602074
Change-Id: Ib269a5363d03c7048abd0c8a9a28df92a773790c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Setting the stapm parameters is causing S3 resume failures and
performance issues. Removing these settings until more testing is
done and the issues are solved.
BUG=b:117252463, b:116870267
TEST=boot grunt
Change-Id: I2299ab81fcc2af0529bfac3be562b05116c64a49
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Angel Pons