The LED polarity was set incorrectly, fix using values derived
from original Chromium sources:
branch firmware-mccloud-5827.B, ToT
src/mainboard/google/mccloud/smihandler.c
src/mainboard/google/mccloud/romstage.c
TEST: boot google/mccloud, observe power LED on normally,
blinking in S3/S4, and off in S5.
Change-Id: Ia1f63eebbccb48fcf8543188db390b23045d843e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Commit 0562783182 applied
this change to other Google boards, but cyan was left out.
Bring cyan in line with other Google boards.
Change-Id: Id86bea538a7b82367ea6ddbd3fe3efb1b1c0078d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Cleaning up code to remove support for pre-EVT rev of cyan board.
Analogous to what was done for intel/strago in commit 103f00d.
Change-Id: I29b32da8064e0743cc9c5df02ce7d3441459ee8f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit a162348.
Remove the hard coded IRQ number for the keyboard interrupt.
IRQ number can change based upon the gpio bank index ordering.
Hence pass the gpio bank and index number so that kernel calculates
the IRQ number.
Original-Change-Id: Icfe5c3995007164bf617575b541758c18ee63a1d
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I81ff19e3060c533ee76023c7651f741294e9db30
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit dc59188.
Disable L1 sub state to prevent WiFi randomly disappear condition.
Original-Change-Id: I8975bb4bbbc2fc89b91b06ae02716367890c672d
Original-Signed-off-by: T.H. Lin <T.H_Lin@quantatw.com>
Original-Reviewed-by: Rajat Jain <rajatja@chromium.org>
Original-Reviewed-by: Vincent Wang <vwang@chromium.org>
Oriignal-Tested-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Change-Id: I51a1bcca6431e6bc28baf9b09433cec13db925c3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit 1138727.
Elan touchscreen driver expects the first gpio resource in asl
to be the reset line.
The driver considers the gpio based irq line as reset gpio resource
and changes the direction to output.
This will cause irq registration to fail.
Solution is to pass Interrupt resource for touchscreen irq
instead of GpioInt.
Original-Change-Id: Ia72d4ad80117f3c0014098113c9027416026e65e
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I1c4b029851e321feeedf713186976fbec42dd82e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit e49deb1.
Configuring UPD PcdCaMirrorEn. This is a board specific parameter.
CA mirror is the Command Address mirroring option that is board
specific.
Original-Change-Id: I05174e18d650332d838e5036c713e91c4840ee75
Original-Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: Ibd0c811d41cb592634f7785edb83ad2f423546c5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to provide new config options to perform LPC and SPI
lock down either by FSP or coreboot.
Remove EISS bit programming as well.
TEST=Build and boot Eve and Poppy.
Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to pass type C USB2 eye diagram for sku Santa,
USB2 port#1 PHY register needs to be overridden.
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
BUG=b:64880573
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: I07c0b7b0f08263a348befb7d6fd8d01028314470
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Move the fchec.h files, which do not seem mainboard specific, out of
the mainboard directories into the southbridge/soc directories.
Change-Id: Idd271c6ab618aa4badf81c702212e7de35317021
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This is not specific to a board but the binary IMC firmware
used on the platform. Also remove unused IMSP and IMWK methods.
Change-Id: I80026bca55f5ba236c080bcd882fc374559942e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
It was not intentional to change oem_fan_control() to non-static
with commit
23e5ba9 binarypi mainboards: Clean up IS_ENABLED fan control
Every platform except bettong had its own static version of
oem_fan_control, so remove the definition of oem_fan_control from imc.h,
and move it out of imc.c into bettong's BiosCallOuts.c.
Change-Id: Ie95ac1fd3a57259bb35796903aa8753ef0e70d70
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21189
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove all checks for #if IS_ENABLED(CONFIG_HUDSON_IMC_FWM) around
the imc.h includes. Convert from #if to if() for all fan control
setup code. Where necessary, make functions non-static to match the
prototypes in imc.h.
Change-Id: If88af42d00227285931829441909a982fc292b2b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Remove all checks for #if IS_ENABLED(CONFIG_HUDSON_IMC_FWM) around
the imc.h includes. Convert all #if to if() for fan control setup.
Change-Id: I04a9fbbf6f64f45e1a0b544267bfe840ce7fa1d9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Don't include src/include/cpu/amd/car.h in Via motherboards.
Change-Id: I9d2b3cfb619cf831c7a677992ca03d5f42e5ffd1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested on T430s with an external screen connected to every one of the
DP ports (miniDP on mainboard, two DP ports on dock), the GRUB payload
can display on both the external screen and the internal LVDS screen.
This is a copy-paste of I8f270d55 "mb/lenovo/x230: Enable libgfxinit".
Change-Id: Ifb1471ecb18927c30c61c64011cbb0e20a465558
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Sync file with southbridge/amd/common/sleepstates.asl.
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Change-Id: I674953f1a5add74e16ddd84c252e8d21501ffefd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Note that against the specs, these definitions repeat
the sleep type also in the reserved fields 3 and 4.
For consistency, don't fix it here now.
Entry for \_S3 is now masked off if HAVE_ACPI_RESUME=n.
Change-Id: Icdc4c81d07fe7a99d5b0f8fa23e9443f58a40ab9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Note that all boards incorrectly had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
SSFG was meant to be used as a mask to enable sleep states
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
State _S3 is now set conditionally if HAVE_ACPI_RESUME=y.
For pi/hudson this had been fixed already preprocessor.
Note that all boards had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
States _S1 and _S2 still appear enabled in ASL/AML
but may not actually work.
TEST: 'cat /sys/power/state' and notice choice 'mem' was
removed from the list of available sleep states.
Change-Id: I27d616871c1771f0c87d8fba23d4ce1569607765
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Kahlee has an ambient light sensor connected to the EC.
TEST=Can see the device in /sys/bus/iio
BUG=b:62030268
Change-Id: Id1138a0fc5270489a734bdf8b1f4ac02d358c0df
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/21146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch assigns the code of coral family, such that,
the 'mosys platform family' returns 'Google_Coral'.
BUG=b:64467244, b:64501879
BRANCH=none
TEST=Examine 'mosys platform family' w/ new firmware.
Change-Id: I1d8f8ca2166a1d80855608cf5b64b0cc7bf3dc93
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/21136
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Six mainboards with Winbond superios directly configure
them in romstage.c. All use the common Winbond romstage
code. Change them to use the common config entry code to
allow for code refactoring such as [1]. Build tested.
[1] https://review.coreboot.org/20988
Change-Id: Icecd52ec622b9da86edb07c52893f4db001e5562
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested:
- i5-3550 and DIMM configurations: 2+0+2+2, 0+2+2+2, 2+2+2+2, 4+2+4+2
- debug output from serial port, EHCI debug port not found
- Arch Linux (Linux 4.11.5) loaded from SeaBIOS, GRUB2, and Linux payload
- all PCI and PCI Express slots
Issues:
- sometimes the machine fails to boot, with serial debug output it can
be seen it stucks after SMM initialization, and more likely to fail
to boot when serial cable is attached
- no S3 resume (not tested in vendor firmware)
Change-Id: I94fbfcee06921538b32aa3c23efa642e7e405ef6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64821783
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I8852e38f01f82b80c2c9718b93baf5894dbd745b
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Current coreboot does not create ACPI device for OS to recognize MELFAS
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64779224
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: If2bc910d641e0cf2b120ed883c5788542959f568
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On this device libgfxinit successfully initializes textmode and
framebuffer mode on the device connected to the HDMI1 port.
VGA port is not tested, due to lack of VGA with valid EDID.
Every ports works on GNU/Linux with kernel version 4.9+80+deb9u1.
Due to limitations within the libgfxinit's current build system,
it needs "select NORTHBRIDGE_INTEL_IVYBRIDGE" to work, even it is
PCH instead of CPU for which libgfxinit should be configured here.
Change-Id: Ib1513fc57b79eebc5d047c2e24585731c44bc215
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The code is based on autoport. I'm using a machine with discrete GPU,
and gfx.* in devicetree.cb is from 2760p.
It can be debug with serial port on dock.
Tested:
- CPU and memory: i5-2540M, 4G+0
- Arch Linux (Linux 4.11.7, SeaBIOS payload, with ATOM BIOS extracted
from vendor UEFI firmware)
- USB ports
- SD card reader
- WLAN
- DP display
- S3
Change-Id: I9c42723ba240a2e9b46998c1a8a708aebc66c604
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is based on autoport. The EHCI debug port is the upper USB
port beside the battery.
Tested and working:
- CPU and memory: i7-3720QM, 4G+4G
- Linux Mint with Linux 4.4 (SeaBIOS payload)
- All USB ports
- ExpressCard
- WLAN
- AC and battery status
- S3
- Other devices detected: DVD drive, smartcard reader, fingerprint, bluetooth
Not tested:
- VGA and DP
- Ethernet and modem
- Dock
Change-Id: I9f3cd124fc676d49add59e9f0a07f70a6bb0fff0
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is based on the code generated by autoport.
The EHCI debug port is between the DP port and eSATA port.
The serial port on dock can also be used for debugging.
The model with discrete graphics is not tested.
Tested and work:
- memory: 0+4G, 4G+0, 4G+4G
- Linux (Arch Linux with kernel 4.10.6) boot from SeaBIOS payload
with native graphics init
- WLAN
- keyboard, trackpoint and touchpad
- USB
- serial port on dock
- fan control
- AC and battery status
(EC) blobs:
This laptop uses SMSC KBC1126 EC, and there are two blobs needed by it.
You can use the tools in util/kbc1126/ to extract them and insert them
to the coreboot image using the following configuration:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: Icbc051e2272b8ea73627940db15a56901d737472
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is generated by autoport.
The flash chip is socketed beside the WLAN slot. The EHCI debug port
is on right side of the laptop beside the RJ11 connector.
Things that work:
- memory: 0+8G, 4G+8G
- Linux (Linux Mint 18.1 with Linux 4.4)
- native graphics init + SeaBIOS payload with SeaVGABIOS
- all 3 USB ports
- WLAN
- WWAN
- SD card reader
- expresscard
- S3 suspend and resume
- internal flashing after IFD is unlocked and coreboot is flashed
- keyboard, trackpoint and touchpad
- fan control
- AC and battery status
Issues:
- Wacom digitizer does not work (even after I add it in DSDT)
- GRUB payload will freeze (in all Elitebooks, including chainloading GRUB
from SeaBIOS)
Things that are not tested:
- smart card reader
- cable modem
(EC) blobs:
This laptop uses SMSC KBC1126-NU as EC. It needs two blobs in the
flash chip. You can use the tools in util/kbc1126 to extract them
from OEM firmware, and use the following configuration to insert
them to coreboot image:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: I3ffdb9f9c71f6c9a84e896abc3c424c8dd4bed0e
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The Giantec semiconductor GT24C16S and ON semiconductor CAT24C16
are the industrial standard electrically erasable programmable
read only memory (EEPROM's) and this patch adds ACPI objects
and power resources for NVMEM device.
Update DOVD method to set sensor IO LDO voltage and remove repetitive
code from OVFI, VCMP and NVMP power resources.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Read the NVMEM content via sysfs interface.
Change-Id: If49ed33b7e1de1eabf317b31ceed8568dfca0aae
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I777247a6b58d3d50b72f12ca2fcab49a06ed5431
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
A decision has been made that boards with LATE_CBMEM_INIT
will be dropped from coreboot master starting with next
release scheduled for October 2017.
As existing implementation of CAR teardown in AGESA can only
do either EARLY_CBMEM_INIT or ACPI S3 support, choose the former.
ACPI S3 support may be brought back at a later date for
these platforms but that requires fair amount of work fixing
the MTRR issues causing low-memory corruptions.
Change-Id: I5d21cf6cbe02ded67566d37651c2062b436739a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Romstages of many 440BX boards included headers that are redundant.
Remove them as part of a bigger cleanup effort.
This finishes off what began in https://review.coreboot.org/20693.
Change-Id: I102a4f6e492eb607b7f88d4c6e15072a8b7fdc46
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I96a0e030bbc5f1c98165e70353340c413f8dc352
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add LPC common code to be shared across Intel platforms.
Also add LPC library functions to be shared across platforms.
Use common LPC code for Apollo Lake soc. Update existing Apollolake
mainboard variants {google,intel,siemens} to use new common
LPC header file.
Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Simplify funciton names and remove reference to hudson in stoneyridge.
The southbridge in Stoney Ridge is Kern and hudson naming is
no longer accurate.
BUG=b:62200157
BRANCH=none
TEST=Build and booted on Kahlee.
Change-Id: Ide7a72dae69b881997101f1e37a1ac739901744d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20912
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new Kconfig option to ignore memory fuses that limit the
maximum DRAM frequency to be used. The option is disabled by
default and should only enabled by experienced users as it
might decrease system stability or prevent a successful RAM
training.
Remove conflicting devicetree settings.
Change-Id: I35dd78a02bcaafce8ba522d253c795d7835bacae
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nicola Corna <nicola@corna.info>
Get rid of old hybrid graphics driver and use the new one.
1. Disable IGD and PEG in early romstage.
The PEG port will get disabled on devices that do not have a
discrete GPU. The power savings are around ~1Watt.
The disabled IGD does no longer waste GFX stolen memory.
2. Get rid of PCI driver
The Nvidia GPU can be handled by the generic PCI driver and allows
to use the ACPI _ROM generator for Switchable graphics.
3. Settings are stored in devicetree.
One driver for all Lenovo hybrid graphics capable devices.
4. Add support for Thinker1 GPU power handling.
Only boards that do use reference design 2012 are known to be
supported. Needs test on boards that do you use reference design 2013.
Should reduce idle power consumption when using IGD by ~5Watt.
Tested on Lenovo T430 without DGPU. PEG port is disabled.
Needs test on all devices.
Change-Id: Ibf18b75e8afe2568de8498b39a608dac8db3ba73
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This mainboard features is an G43 northbridge, ICH10 southbridge and
Winbond W83627dhg SuperI/O. This board is impossible to flash
internally with vendor bios (BIOS region is WP and other regions like
IFD and ME are read only and inaccessible respectively). Due to either
ICH10 or board layout it is also impossible to do ISP, which requires
desoldering flash chip. To make hacking more easy there is an empty
SPI header next to spi flash pads which can be hooked up to a SPI
flash.
What works:
* 2 DDR2 dimms per channel (tested with 1+2G in CH0 and 2+2G in CH1);
* SATA with AHCI
* Integrated GPU with option rom (extracted from a Gigabyte vendor
bios)
* VGA (on DVI) with NGI if patched to use DVI gmbus port for output
* PCI
* Reboot and S3 resume
* Descriptor mode with ME disable straps and ME region absent (no
working gbe in this configuration though)
* USB.
What does not work:
* GBE (probably requires working ME);
* Analog on DVI port out is shaking, which is not the case with vendor
BIOS (setting clockgen on smbus 0x69 like vendor fixes it).
* Booting with ME enabled (needs raminit patches for that)
Not tested:
* Sound;
* All the rest.
Not coreboot related problems:
* Flashing this board with vendor bios is a PITA and requires
desoldering flash chip;
* In situ programming is not possible.
TESTED with SeaBIOS and Linux 4.10.8
Change-Id: If27280feb7cbf0a88f19fe6a63b1f6dbcf9b60f4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Updating the common smihandler to handler gpi events which
originally were going to be left to each soc to handle. After
some more analysis the gpi handler can also be commonized.
Change-Id: I6273fe846587137938bbcffa3a92736b91982574
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/20917
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each line of spd config overwriting the slot 0 instead
of appending it.
Change-Id: I0124aa34f1d4fcb30810fb7eef03d4828a7ac430
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-on: lenovo x1 carbon gen 1 with elpida 8GB
Fixes: e9787ff61f ("mb/lenovo/x1_carbon_gen1: Add 4GiB SPD index 2")
Reviewed-on: https://review.coreboot.org/20918
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The schematics isn't available for the board, but other L*00 series boards
seem to use a different, compared to T*00 series, GPIO layout.
As it has never been tested, remove the broken driver.
Change-Id: I4bfa02fdbc5da5b556010c2f300faaf6dc845b80
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Configuring the clockgen like vendor bios fixes the issue where the
display wobbles from left to right on the analog VGA output.
Note: This seems to be common issue/requirement on Intel devices from
that generation (also happens on dg43gt).
TESTED on Intel D510MO.
Change-Id: I08449f0b8b90a1781e6dec91140bf219ea07aaf9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19595
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
some gpio irq need to set input pull initialization status
to guarantee to get the right irq trigger. let's add this argument
in gpio_input_irq() function
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I9b8e6497f07146dafdb447a6ea10d039a2a2fa33
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Decrease the link-frequencies as recommended by Omnivision for OV13858
and OV5670 camera sensors.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successful.
Change-Id: I78fb2d3527f66b5147123a9c8fc4cb95650f86b6
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
GPP_B8 acts as input to the inverter whose output controls PERST#
signal to wifi module. Out of reset, GPP_B8 is configured as
input by default. Since there is no external pull-down on it, this
line is floating and results in PERST# being asserted until ramstage
where the GPIO was originally configured. Because of this the wifi
chip is not ready during the PCIe initialization step. Move the
configuration of GPP_B8 to bootblock so that wifi device is taken out
of reset as early as possible.
BUG=b:64181150,b:62726961
TEST=Verified with warm reboot and suspend-resume stress test that
wifi is still functional.
Change-Id: I68e1bd67499262a17daade72e9a9fd32934a184d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add gpio.c to bootblock so that the variant early_gpio_table can be
used for configuration in bootblock.
BUG=b:64181150,b:62726961
Change-Id: I77181334257f2fd19982ecafc1f58afe912f4280
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use the genric GPIO library. Add the required functions.
Also, update the Kahlee mainboard dependency to match.
Change-Id: I2ea562b052401efff3101f736788ca77d21e6de6
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20543
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We define BINARYPI_LEGACY_WRAPPER a method of calling AGESA
via functions in agesawrapper.c file. The approach implemented
there makes it very inconvenient to do board-specific
customisation or present common platform-specific features.
Seems like it also causes assertion errors on AGESA side.
The flag is applied here to all boards and then individually
removed one at a time, as things get tested.
New method is not to call AGESA internal functions directly,
but via the dispatcher. AGESA call parameters are routed to
hooks in both platform and board -directories, to allow for
easy capture or modification as needed.
For each AGESA dispatcher call made, eventlog entries are
replayed to the console log. Also relocations of AGESA heap
that took place are recorded.
New method is expected to be compatible with binaryPI.
Change-Id: I2900249e60f21a13dc231f4a8a04835e090109d5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We define AGESA_LEGACY_WRAPPER a method of calling AGESA
via functions in agesawrapper.c file. The approach implemented
there makes it very inconvenient to do board-specific
customisation or present common platform-specific features.
Seems like it also causes assertion errors on AGESA side.
The flag is applied here to all boards and then individually
removed one at a time, as things get tested.
New method is not to call AGESA internal functions directly,
but via the dispatcher. AGESA call parameters are routed to
hooks in both platform and board -directories, to allow for
easy capture or modification as needed.
For each AGESA dispatcher call made, eventlog entries are
replayed to the console log. Also relocations of AGESA heap
that took place are recorded.
New method is expected to be compatible with binaryPI.
Change-Id: Iac3d7f8b0354e9f02c2625576f36fe06b05eb4ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In Scarlet pwm regulatoror minimum value and maximum value differs from
other board variants, Correct it so we can get the right voltage.
Change-Id: I1f722eabb697b3438d9f4aa29c205b0161eb442a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
