The search loop for UMA resource was only used to check for the highest
RAM address below 4GB. The cached values from BSP CPU can now be used
for the replication.
Change-Id: I5244ffa6f8a93f5ff5aaf8a71bd006b0f9cd518a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1388
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Take a copy of BSP CPU's TOP_MEM and TOP_MEM2 MSRs to be distributed
to AP CPUs and factor out the debugging info from setup_uma_memory().
Change-Id: I1acb4eaa3fe118aee223df1ebff997289f5d3a56
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1387
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This was broken, fixing according to related patch for i945
Change-Id: I925cd205ee5beb918181740a7b981a4209688ac6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1412
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CPU can arbitrarily reorder calls to rdtsc, significantly
reducing the precision of timing using the CPUs time stamp counter.
Unfortunately the method of synchronizing rdtsc is different
on AMD and Intel CPUs. There is a generic method, using the cpuid
instruction, but that uses up a lot of registers, and is very slow.
Hence, use the correct lfence/mfence instructions (for CPUs that
we know support it)
Change-Id: I17ecb48d283f38f23148c13159aceda704c64ea5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1422
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Adding ranges directly into coreboot memory table raised issues
as those methods bypassed the MTRR setup. Such regions are now
added as resources, so declare the functions again as static.
Change-Id: If78613da40eabc5c99c49dbe2d6047cb22a71b69
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1415
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Dropping mainboard's chip.h broke execution of the mainboard's enable
function and the addition of mainboard specific smbios tables.
The former was fixed by Kyosti in http://review.coreboot.org/1374
This patch fixes the breakage in static.c and also backs out a small
portion of Kyosti's patch (because it's not needed anymore)
Change-Id: I6fdea9cbb8c6041663bd36f68f1cae4b435c1f9b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1421
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
These existed to provide a hook to add reserved memory regions
in the coreboot memory table. Reserved memory are now
added as resources.
Change-Id: I9f83df33845cfa6973b018a51cf9444dbf0f8667
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1414
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Use of lb_add_memory_region() is reduntant with the MMCONF
resource being set as reserved.
Change-Id: I747ea34823692b6966b2e50d22aea1fb89c73c25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1394
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The function is a noop for all but amd/serengeti_cheetah.
Change-Id: I09e2e710aa964c2f31e35fcea4f14856cc1e1dca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1184
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The names were set at various times during development, but
the way the code works, you might end up with the wrong name
being displayed in the logs. Instead of doing magic, just
display both names for each component
Change-Id: I1f8ce44d156442f5f7d717e1a2b47ed1218d4527
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1413
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Move beep commands to board-specific area as they need to be different for
different codecs.
Change-Id: I2a1ac938c49827cc816a95df10793a7e234942bf
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: http://review.coreboot.org/1410
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use IORESOURCE_RESERVE to exclude the region from system RAM table.
Change-Id: I61b51022165e1304a41554f67af75b3089d892af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1393
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Apply the change
http://review.coreboot.org/1390
to all the AMD southbridge.
Change-Id: I8e94014f8883a0408b68355d9aa33aea4373881f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1406
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Move the POST display to take place just before jumping
the payload, a bit later than before.
Change-Id: Ie1d1ff24dc6c1640e25681be7dc5740943c7f112
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1396
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Some mainboards have really nice capabilities for posting, beyond
simple POST cards. Further, some can not use a POST card. This
change defines a weak symbol (mainboard_post) that can be overridden
by a real mainboard_post function.
If, for example, you'd like to do something fancy before the payload starts,
you can add this to mainboard.c:
void mainboard_post(u8 value)
{
switch(value){
case POST_TIME_TO_PARTY: some_fancy_lights();
break;
}
}
Maybe the post function should be an entry in the device. We're beginning to over-use
weak symbols.
BUG=None
TEST=Build and boot a google chromebook. Observe that it still works. Use it to drive
some pretty lights.
Change-Id: I3512d2ec34a66c747287191851c3f68b6a7cc1b2
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1397
Tested-by: build bot (Jenkins)
In accordance to PCH EDS 14.1.35.1
Change-Id: I2e6cec6d4f49f404e33a171a8fbd6e4880327896
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1411
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We thought about two ways to do this change. The way we decided to try
was to
1. drop all ops from devices in romstage
2. constify all devices in romstage (make them read-only) so we can
compile static.c into romstage
3. the device tree "devices" can be used to read configuration from
the device tree (and nothing else, really)
4. the device tree devices are accessed through struct device * in
romstage only. device_t stays the typedef to int in romstage
5. Use the same static.c file in ramstage and romstage
We declare structs as follows:
ROMSTAGE_CONST struct bus dev_root_links[];
ROMSTAGE_CONST is const in romstage and empty in ramstage; This
forces all of the device tree into the text area.
So a struct looks like this:
static ROMSTAGE_CONST struct device _dev21 = {
#ifndef __PRE_RAM__
.ops = 0,
#endif
.bus = &_dev7_links[0],
.path = {.type=DEVICE_PATH_PCI,{.pci={ .devfn = PCI_DEVFN(0x1c,3)}}},
.enabled = 0,
.on_mainboard = 1,
.subsystem_vendor = 0x1ae0,
.subsystem_device = 0xc000,
.link_list = NULL,
.sibling = &_dev22,
#ifndef __PRE_RAM__
.chip_ops = &southbridge_intel_bd82x6x_ops,
#endif
.chip_info = &southbridge_intel_bd82x6x_info_10,
.next=&_dev22
};
Change-Id: I722454d8d3c40baf7df989f5a6891f6ba7db5727
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1398
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Apply the change
http://review.coreboot.org/1265
to all the AMD northbridge.
Change-Id: Idf3994c1e9ec76cd19db9f740d825cf24059884f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1404
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Apply the change
http://review.coreboot.org/1264
to all the AMD northbridge.
Change-Id: Ied74d6f579d2c0350288e2619d7810f8d44fa574
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1403
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The board had HAVE_MAINBOARD_RESOURCES=0 so this was never
called. Drop unnecessary includes too.
Change-Id: Ia7bddf29a16966c052b5cabbb47029299e6dbd12
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1392
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Detection for a hyper-threading CPU was not compatible with multicore
CPUs. When using CPUID eax==4, also need to set ecx=0.
CAR init tested on real hardware with hyper-threading model_f25 and
under qemu 0.15.1 with multicore CPU.
Change-Id: I28ac8790f94652e4ba8ff88fe7812c812f967608
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1172
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Commit 188e3c2ff0 dropped mainboard
out of the static device tree. This left dev_root->chip_ops unset,
and mainboard_ops.enable_dev() was no longer called.
Change-Id: I6d447c8049a66041b8bb36ec9aac3e7e0d20a99b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1374
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If the CMOS is cleared or someone writes some random date/time
on purpose, the CMOS date register has a invalid date. This will
hurts some OS, like Windows 7, which hangs at MS logo forever.
When we detect that, we need to write a reasonable date in CMOS.
Alexandru Gagniuc:
Hmm, it would be interesting to use the date the coreboot image
was built and set that as the default date. At least until time
travel is invented.
Change-Id: Ic1c7a2d60e711265686441c77bdf7891a7efb42e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1389
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The field device in PCI_ADDRESS only takes 5 bits. So if the device number is
more than 32, it will truncated to 5 bits. Before this patch, other pci devices
will be incorrectly probed as processor node.
Change-Id: I64dcd4f4fda7b7080a9905dce580feb829584b94
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1264
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Parmer and thather hang at windows 7 booting process. Setting the
valid date in CMOS can fix that.
Change-Id: I5e427cfb42430ebebdb4c1e48bd25860c0fec45f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Thatcher features: Family 15 trinity FP2. Hudson.
close to Parmer.
This board and parmer both need to revert the change
http://review.coreboot.org/#/c/1359/, and add thatcher's own
chip.h,otherwise the mainboard_enable can not be called.
Change-Id: I54e1cfca845fbcea1d3aad5eff08d760d0d215c9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1382
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Before (data flag ignored -> broken):
66 DATA:
e944f1 JMP 1ff6
After (fixed):
66 DATA:
e944f1ffff JMP 00001ff8
This subtle difference in the length of decoded instruction meant
that the VBE call jumped to the routine setting AX=0x14F (VBE Failed)
instead of the routine that set AX=0x4F (VBE success).
The ability to run the same code in vm86 significantly aided the
debugging of this issue. Those X.org developers who would like to drop
vm86 better take special care towards _all_ vesa bugs, as those will
expose further issues.
Imported from:
http://cgit.freedesktop.org/xorg/xserver/commit/hw/xfree86/x86emu?id=cc2c73ddcb4370a7c3ad439cda4da825156c26c9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Id08ead9b17468cf19ede45508e5dcc50e45b5acf
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Tested-by: Luc Verhaegen <libv@skynet.be>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-on: http://review.coreboot.org/1365
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
cc2c73ddcb4370a7c3ad439cda4da825156c26c9's three-cent titanium tax
doesn't go too far enough. Fix the rest of the call and jmp
instructions to handle the data prefix correctly.
Reference: Intel 64 and IA-32 Architectures Software Developer's Manual
Volume 2A: Instruction Set Reference, A-M
http://www.intel.com/Assets/PDF/manual/253666.pdf
Imported from:
http://cgit.freedesktop.org/xorg/xserver/commit/hw/xfree86/x86emu?id=bb18f277156c08be028a6e12d8987fb1593e9168
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I83e6245d9748ee86722cfb7d8ac65258c35c013c
Reviewed-by: Julien Cristau <jcristau@debian.org>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-on: http://review.coreboot.org/1366
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch validates the previous "drop uma_memory_base" patches;
there are no more references to uma_memory_base when GFXUMA is not
selected.
Change-Id: I735b5e765b0c5cb4af1b4a7470cfe1af2bda7d38
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1385
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
UMA region can be determined at any time after the amount
of RAM is known and before the uma_resource() call.
Change-Id: I2a0bf2d3cad55ee70e889c88846f962b7faa0c7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1379
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Without GFXUMA, variables were not referenced anywhere.
Fail builds on Family10 if GFXUMA is selected, because the northbridge
code does not set UMA base or size.
Change-Id: I15b91cf6241e9a890398eed03824b753828a0a51
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1247
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The code in rs690 or rs780 is always used with K8 or AMDFAM10
northbridge. Without GFXUMA, both of these set the same static value
indirectly using the variable uma_memory_base.
Make the register setting with immediate value, to remove the obscure
use of variable uma_memory_base.
Change-Id: I5354684457a76e73013b4e34a4538a6d122eee8d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1246
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
I dont known if missed something, but why an extra 0x100 was added to limit?
My board would get the wrong memory table entry 7f000000-7fffffff as RAM, which
is higher than TOM.
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000c0000-000000005e13efff: RAM
3. 000000005e13f000-000000005effffff: CONFIGURATION TABLES
4. 000000005f000000-000000007effffff: RESERVED
5. 000000007f000000-000000007fffffff: RAM
6. 00000000a0000000-00000000afffffff: RESERVED
Ronald G. Minnich:
I think someone who wrote the code was trying to round up the
next 0x100 boundary and did it incorrectly.
Here is code that would do it correctly:
limitk = ((resource_t)((d.mask + 0x00000ff) & 0x1fffff00)) << 9 ;
Zheng:
Plus 0xFF is correct, but the d.mask take bit 0 as enable it.
This bit should be clear when we try to calculate the limitk.
Change-Id: I3848ed5f23001e5bd61a19833650fe13df26eef3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1265
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use of uma_resource() in northbridge code created a memory
resource marked as reserved. Such resources are removed
from system memory in write_coreboot_table().
Change-Id: I14bfd560140d8d30ec156562f23072bfae747bde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1238
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
With SandyBridge northbridge code, uma_memory_size was reset to
zero before variable MTRRs were set. This means MTRR setup routine
did not previously create a un-cacheable hole for uma.
Keep the behaviour that way, mmio_resource() has a prerequisuite that
the new region does not overlap with any cacheable ram_resource().
The result is not optimal setup in the number of used MTRRs, but
continue with this approach until MTRR algorithm is improved.
Change-Id: I63c8df19ad6b6350d46a3eca3055abf684b8b114
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reserved memory resources will get removed from memory table at
the end of write_coreboot_table(),
Change-Id: I02711b4be4f25054bd3361295d8d4dc996b2eb3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1372
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This reverts commit 042c1461fb.
It turned out that sending IPIs via broadcast doesn't work on
Sandybridge. We tried to come up with a solution, but didn't
found any so far. So revert the code for now until we have
a working solution.
Change-Id: I7dd1cba5a4c1e4b0af366b20e8263b1f6f4b9714
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1381
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit 78efc4c36c.
The broadcast patch was reverted, so this commit should also
be reverted. The reason for reverting the broadcast patch:
It turned out that sending IPIs via broadcast doesn't work on
Sandybridge. We tried to come up with a solution, but didn't
found any so far. So revert the code for now until we have
a working solution.
Change-Id: I05c27dec55fa681f455215be56dcbc5f22808193
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1380
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some usb debug devices don't respond fast enough. The linux kernel
(which uses almost the same usbdebug code) added a bit more
retry code, so let's copy that. Even if it might look stupid,
i pass the DBG_LOOPS argument through all functions to keep
the code at least a bit in sync with the linux kernel code.
Change-Id: I7c4b63b8bf1d2270fd6b8c8aa835e2cb324820bd
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1375
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Compilation fails with set_debug_port undeclared in ramstage and
smm code. Fix that by adding usb_debug.c to the appropriate stages.
Change-Id: I2a037d3c5fab76ae6ea65c3a7f4d4e7561bb6d34
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1376
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
MRC messes with USB devices, so we have to reinitialize
USB debug after MRC has finished.
Change-Id: I45c0a687cebd69d0a31235bb870f8c455f42d4f2
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1377
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit 2d42b34003 changed the
variable MTRR setup and removed compensation of uma_memory_size in
the cacheable memory resources.
Since the cacheable region size was no longer divisible by a large
power of 2, like 256 MB, this caused excessive use of MTRRs.
As first symptoms, slow boot with grub and poor user response.
As a solution, register the actual top of low ram with ram_resource(),
and do not subtract the UMA/TSEG regions from it.
TSEG may require further work as the original did not appear exactly
right to begin with. To have UMA as un-cacheable, use uma_resource().
Change-Id: I4ca99b5c2ca4e474296590b3d0c6ef5d09550d80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1239
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: build bot (Jenkins)
This instruction is being used in some debug VBIOSes. This implementation
doesn't even try to be accurate. Instead, it just increments the counter by a
fixed amount every time an rdtsc instruction in encountered, to avoid divides
by zero.
Imported from:
http://cgit.freedesktop.org/xorg/xserver/commit/?id=c4b7e9d1c16797c3e4b1200b40aceab5696a7fb8
Change-Id: I8fba1a060c57ccb7bbd44aa321dd349bc56bf574
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1362
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
No need for the test, tomk is at most 1GB on these chipsets.
Even if there was no room, adjusting the memory resource would not
not divert accesses in the hardware from DRAM to PCI.
Change-Id: I2213b8d9d2e6ab8da8fd3e8081cc62bb05b6b316
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1369
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
No need for the test, tomk is top of low memory and always below 4GB.
Change-Id: Ifc8f29268b761aa9b07b578673236a673f0c70b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1368
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Hide some details of the resource allocator from rest of the world.
These should come in handy when fixing some aspects of MTRR setup.
Change-Id: I8acad98f25e56cd8bae64fb52539d81ce94f9c73
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
mainboard_config never worked right, at least not since we've had sconfig.
Hence, drop mainboard/<vendor>/<device>/chip.h and fix up the mainboards that
tried to use it anyways.
Change-Id: I7cd403ea188d8a9fd4c1ad15479fa88e02ab8e83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1359
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Modelled after http://review.coreboot.org/#/c/443 to get bd82x6x in
sync.
Change-Id: I36d715310157b9f9074f2a1c80710f85833020b4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1324
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
LX has two values that are usually automatically derived but can
be overridden, that were so far defined in each board's romstage.
These values, along with the toggle to enable override are now
part of LX's Kconfig. For boards that gave values but requested
autogeneration, the values are removed.
Further improvements: Figure out the various fields in PLLMSRlo
and make them sensible Kconfig options (instead of the hex value
it is now)
Change-Id: I8a17c89e4a3cb1b52aaceef645955ab7817b482d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1227
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Otherwise there is a flurry of TDP changes with suspend/resume
as the kernel powers devices off on suspend and brings them
back online in resume.
This also adds a mutex around the TDP operations since it is
split across two methods and can't just rely on being Serialized.
Change-Id: I7757d3ddad34ac985a9c8ce2fc202e2b2dcb2527
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Recent changes in EC/Vboot/U-boot have completely broken
the logging of developer and recovery modes.
Recovery mode may not be in VBNV, so if that is zero and
yet we are in recovery mode then assume it is there because
the button/key was pressed.
Since there may not be any actual developer mode switch
we look if option rom is loaded and the system is not
in recovery mode and consider that as developer mode.
Change-Id: I70104877b24de477217e1ff5b3a019aef22343ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will log if the ME is disabled or has an error.
1) disable ME via EC console: gpioset PCH_HDA_SDO 1
2) boot the device
3) read eventlog with "mosys eventlog list"
71 | 2012-07-13 10:10:55 | Management Engine | Disabled
Change-Id: I9f6ee452d2aea76e6a5ea2cd50a50ff36245692a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The required power MSRs are mirrored in MCHBAR so
it is possible to configure TDP at runtime via ASL.
This adds the required fields and a set of methods to
configure "TDP down" and "TDP nominal". It explicitly
does not support "TDP up" at the moment.
PSSS: method is added to assist in searching the _PSS
table for the appropriate entry that corresponds to the
desired max non-turbo ratio.
STND: Set TDP Down from Nominal. This will limit CPU to
the TDP down configuration by sequencing the required
changes in the right order.
STDN: Set TDP Nominal from Down. This will set the CPU
back to nominal configuration by sequencing the required
changes in the correct (reverse) order.
This does not introduce any functional changes and must
be paired with additional changes to be useful.
The current configured TDP can be checked to see that
the transition to/from a desired level is successful.
> mmio_read8 0xfed15f50
0x00 # TDP-Nominal
> mmio_read8 0xfed15f50
0x01 # TDP-Down
Change-Id: I31a2f30cc9d134cc5eee980ae9288ae45e71c6e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1344
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The default TCC activation offset is 0, which means TCC
activation starts at Tj_max. For devices with limited
cooling ability it may be desired to lower TCC activation.
This adds an option that can be declared in the devicetree
to set the TCC activation to a non-zero value.
Enable tcc_offset=15 in devicetree.cb and build/boot
the BIOS and check that the value is set in the MSR:
> and $(shr $(rdmsr 0 0x1a2) 24) 0xf
0xf
Change-Id: I88f6857b40fd354f70fa9d5d9c1d8ceaea6dfcd1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1343
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Split this behavior out from PNOT() so the OS can
update _PPC limit without re-reading C-state tables.
Change-Id: I81b9111a4866f6b9916f74ac57a3caefaa77c565
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1342
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The existing NVS variable for PPCM will be used to
select a dynamic max P-state.
By itself this does not change existing behavior because
the NVS PPCM variable is initialized to zero.
PPCM can be tested by building and booting a modified BIOS
that sets gnvs->ppcm to a value greater than 1 and checking
from the OS that the P-state is limited to that value.
Change-Id: Ia7b3bbc6b84c1aa42349bb236abee5cc92486561
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1341
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will allow various teams to select which thermal sensor
will control the thermal zones.
Also add a method to notify the thermalzones of a change
so these threshold/sensor methods take effect.
Needs a modified BIOS that uses the NVS TMPS value in
the thermalzone to read a different sensor.
Then, use a kernel driver that contains the following:
/* Adjust temperature sensor id to 2 */
union acpi_object param;
struct acpi_object_list input;
param.type = ACPI_TYPE_INTEGER
param.integer.value = 2
input.count = 1;
input.pointer = ¶m;
acpi_evaluate_object(NULL, "\\TMPU", &input, NULL);
And ensure that the temperature sensor that is being
monitored switches to ID 2.
Change-Id: I6319741358ba31eb8a3dc635d64f3f0acf683386
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME device was being sent EOP and the PCI device hidden during
coreboot so it was not available in the SMI finalize step.
This also flips the PCI vendor/device dword around for the match.
Boot on Panther Point with serial and SMI debugging enabled and see
that ME EOP message is sent and the device is hidden at end of
U-boot and before the kernel loads.
Finalizing Coreboot
SMI# #0
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PM1_STS: TMROF
PM1_EN: 120
Starting kernel ...
Change-Id: I230038c62c50db2a1c94078c0a2a67bdc232440e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1338
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The LPC bus normally allocates the range for legacy devices,
0-0x1000. Some devices on LPC are above that range and need to
be accounted for. Check the decode range settings for addresses
> 0x1000 and reserve them.
Change-Id: Idba800d7cee3185296f29dd237ba306f3de8de55
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1337
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Events are logged for SMIs that trigger ACPI sleeps state
entry and when the power button press triggers an SMI such
as at the developer/recovery screens.
Generate ACPI sleep state events and power button
events and verify they show up in the log:
153 | 2012-06-23 17:12:59 | ACPI Enter | S5
184 | 2012-06-23 17:15:50 | ACPI Enter | S3
216 | 2012-06-23 17:28:58 | Power Button
Change-Id: Iba134d619780e459bce189d36d57844997ffb009
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1320
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Unfortunately the drive strength values are very much board
specific and different between mobile and desktop so we don't
try to do any fancy detection here but let it be specified
directly in the devicetree.
Change-Id: I66674bff0de04ecd088fb09afad1cf801a374df2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to support the GSMI interface the SMI handler needs
to find and use the state save area from the same CPU that
initiated the SMI. In this case it is a synchronous SMI
resulting form an IO write to port 0xB2.
To find the right CPU state save area iterate over the region
until the "IO Misc Info" field reports the expected value and
then proceed to use that state save area.
This is needed because the coreboot SMI handler only executes on
one core, and that core is non-deterministic. It is likely that
the core executing the C SMM handler is not the same one that
actually did the IO write to 0xB2 and generated the SMI.
The GSMI parameter buffer is passed as a pointer to EBX in the
tate save area, and the GSMI command is extracted from EAX before
it is used as the return value.
This interface is tested by enabling CONFIG_GOOGLE_GSMI in the
kernel and generating events and verifying that they end up
in the event log.
159 | 2012-06-23 16:22:45 | Kernl Event | Clean Shutdown
184 | 2012-06-23 17:14:05 | Kernl Event | Oops
185 | 2012-06-23 17:14:05 | Kernl Event | Panic
Change-Id: Ic121ea69e9f50c88467c435e095c3e3629989806
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Read event routine didn't get the correct BIOS callout. So it could not get
the heap address. Then it would creat many warning in serial port.
Change-Id: Ia35601bda1579c7f726ed767d7be78713ac185d2
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The board has a marvell NIC, but the driver to disable NIC BIOS was adapted
from a Realtek 8168 driver. Rename to reflect the change.
Also hook up as driver, so coreboot can actually find it.
Change-Id: Ibdfd6074eb28ba537d68552a3346b06493cef2a6
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
One copy was slightly different, but all the differences were commented out
Change-Id: I3cc7b5621c681a1eb286f9b16ef3ebdce03abb6b
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1356
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
EHCI debug allows to send message with 8 bytes length, but
we're only sending one byte in each transaction. Buffer up
to 8 bytes to speed up debug output.
Change-Id: I9dbb406833c4966c3afbd610e1b13a8fa3d62f39
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1357
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
On SandyBridge systems configured to work with Panther Point the CPU
would wrongly be described as IvyBridge. Fix this issue and drop an
unneeded Kconfig variable at the same time.
Change-Id: I501a4fa00613e589cd315cfee61b2f9561dfcb4d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1335
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The linux kernel contains an SMI driver that was written by
me (Duncan) and upstreamed a couple years ago called GSMI.
This driver will format a parameter buffer and pass pointers
to this parameter buffer to the SMI handler. It uses this to
generate events for kernel shutdown reasons: Clean, Panic, Oops,
etc.
This function expects to be passed pointers into the SMM state
save area that correspond to the prameter buffer and the return
code, which are typically EAX and EBX.
The format of the parameter buffer is defined in the kernel
driver so we implement the same interface here in order to be
compatible.
GSMI_CMD_HANDSHAKE: this is an early call that it does to try
and detect what kind of BIOS is running.
GSMI_CMD_SET_EVENT_LOG: this contains a parameter buffer that
has event type and data. The kernel-specific events are
translated here and raw events are passed through as well which
allows any run-time event to be added for testing.
GSMI_CMD_CLEAR_EVENT_LOG: this command clears the event log.
First the gsmi driver must be enabled in the kernel with
CONFIG_GOOGLE_GSMI and then events can be added via sysfs
and events are automatically generated for various kernel
shutdown reasons.
These can be seen in the event log as the 'Kernel Event' type:
169 | 2012-06-23 15:03:04 | Kernl Event | Clean Shutdown
181 | 2012-06-23 16:26:32 | Kernl Event | Oops
181 | 2012-06-23 16:26:32 | Kernl Event | Panic
Change-Id: Ic0a3916401f0d9811e4aa8b2c560657dccc920c1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When fixing the SMM state table for SandyBridge/IvyBridge CPUs
the wrong table was used for older 64bit capable CPUs.
Change-Id: Ia7dff21aa3f0e5aa61575634fc839777de6bef10
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1353
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a temporary workaround so the SPI bus can be accessed
at runtime in SMM code until the SPI opcode menu is used
properly.
Change-Id: I93d188c55b66d8dce49fa91a1de53ee195944b30
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is called from the SMI handler install because those
setup functions clear many of these registers.
Ensure that these events show up in the log as appropriate.
Example log output:
159 | 2012-06-23 14:31:54 | SUS Power Fail
160 | 2012-06-23 14:31:54 | System Reset
161 | 2012-06-23 14:31:54 | ACPI Wake | S5
Change-Id: I48c423c10ee7e6c2829bcc95f6cfabb4979c25a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If a Chrome OS device is in developer mode log an event.
When the device is in recovery mode also log an event
and provide the recovery reason.
Enable developer mode and trigger recovery mode and
verify that the events are logged:
238 | 2012-06-23 17:31:56 | Chrome OS Developer Mode
239 | 2012-06-23 17:31:56 | Chrome OS Recovery Mode | User Requested from Developer Screen
Change-Id: I14d41f44e04fd91340569617c7314da7e35a154f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1321
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On both SandyBridge and IvyBridge BCLK is fixed at 100MHz. Have the
comment reflect that.
Change-Id: Ia81c3501dc3e68cf3143c3bc864dfbf88901f9f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1336
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
.. in case the system has pluggable CPUs or might come in different SKUs.
Change-Id: I7a7cd95b4de5dd78370355f448688e8d000434c1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1333
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is for GfxInitSview(GnbSview.c). It would create warning message if it
could not get VBIOS image.
Change-Id: I3b2726f612b4b7a237644a4b63b56efad52b7ab5
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1351
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The default return value should be AGESA_SUCCESS, which is zero. If it was set as TRUE,
the AGESA wrapper would think it was AGESA_UNSUPPORTED. That would make no sense. And it
would produce ASSERT warning in AGESA wrapper.
On my parmer board, with Engine sample processor, it can not create the correct DMI table.
Routine initlate will return AGESS_ERROR.
------Serial message---------
ASSERTION FAILED: file 'src/mainboard/amd/parmer/agesawrapper.c', line 427
DmiTable:100123c3, AcpiPstatein: 10010126, AcpiSrat:0,AcpiSlit:0, Mce:100111ba, Cmc:1001127c,Alib:1001ccd4, AcpiIvrs:0 in agesawrapper_amdinitlate
agesawrapper_amdinitlate failed: 5
-----------------------------
I believe the processor with acceptable name string will create the right DMI.
Change-Id: Ie86955cf9affffc964a7c9f4a2c63077ef2030de
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove the warning message from linux dmesg,
mtrr: your BIOS has configured as incorrect mask, fixing it.
Change-Id: I355509db12ab10c33b7c1c23e2c7c4783f30e67e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1349
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2048 * ONE_MB will cause warning,
src/northbridge/amd/agesa/family15tn/northbridge.c:667:50: warning: integer overflow in expression [-Woverflow]
I guess it will change the data type to signed integer.
I think the bit shifting is better.
Change-Id: I823f7ead1f7d622bf653cb3bf2ae2343f5e76805
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1263
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This function is exported so it can be used in other
places that need similar relocation due to TSEG.
Change-Id: I68b78ca32d58d1a414965404e38d71977c3da347
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1310
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Date and time are mixed up:
microcode: updated to revision 0x12 date=2012-12-04
should be
microcode: updated to revision 0x12 date=2012-04-12
Change-Id: I85f9100f31d88bb831bef07131f361c92c7ef34e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1334
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
This patch extends the current smbios api to allow changing mainboard
serial and version during coreboot runtime. This is helpful if you
have an EEPROM etc. to access these informations and want to add
some quirks for broken hardware revision for the linux kernel.
This could be done via DMI_MATCH marco.
Change-Id: I1924a56073084e965a23e47873d9f8542070423c
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1232
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
coreboot used to pass some information to u-boot in the coreboot table
and other information in a modified flat device tree. Since the FDT code
was never upstreamed and removed from our tree, u-boot was changed to
get the information it needs from the coreboot table alone. However,
in the process of this change only the vboot shared data structure was
passed on by coreboot, so when u-boot tried to update the ChromeOS
specific ACPI entries, it would accidently overwrite the vboot data.
This patch passes on the ChromeOS specific ACPI data structure instead
of the vboot shared data. Another change to u-boot will teach it how
to get to the vboot shared data from there.
Change-Id: Ifbb64eafc0d9967887b4cdeebf97d0c4ce019290
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1282
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The LAPIC timer is running at BCLK (100MHz) on Sandy Bridge and Ivy
Bridge systems. However, the current timer code assumed that the clock
would run at 200MHz instead. This made all delays twice as long as
needed.
Change-Id: I41b1186daee11cfd9a25b3a9d5ebdeeb271293c7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1330
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This maintains a 32bit monotonically increasing boot counter
that is stored in CMOS and logged on every non-S3 boot when
the event log is initialized.
In CMOS the count is prefixed with a 16bit signature and
appended with a 16bit checksum.
This counter is incremented in sandybridge early_init which is
called by romstage. It is incremented early in order notice
when reboots happen after memory init.
The counter is then logged when ELOG is initialized and will
store the boot count as part of a 'System boot; event.
Reboot a few times and look for 'System boot' events in the
event log and check that they are increasing. Also verify
that the counter does NOT increase when resuming from S3.
171 | 2012-06-23 16:02:55 | System boot | 285
176 | 2012-06-23 16:26:00 | System boot | 286
182 | 2012-06-23 16:27:04 | System boot | 287
189 | 2012-06-23 16:31:10 | System boot | 288
Change-Id: I23faeafcf155edfd10aa6882598b3883575f8a33
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1315
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This standared SMBIOS 0able describes the location and format
of the event log to the OS and applications. In this case the
pointer is a 32bit physical address pointer to the log in
memory mapped flash.
Look for SMBIOS type15 entry with 'dmidecode -t 15'
Handle 0x0004, DMI type 15, 23 bytes
System Event Log
Area Length: 4095 bytes
Header Start Offset: 0x0000
Header Length: 8 bytes
Data Start Offset: 0x0008
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFB6F000
Status: Valid, Not Full
Change Token: 0x00000000
Header Format: OEM-specific
Supported Log Type Descriptors: 0
Change-Id: I1e7729e604000f197e26e69991a2867e869197a6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1314
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
MRC returns specific error codes; print the according error
message if we know what it means.
Change-Id: Iaaf1512b9d577d4291fccfb94d879043ab5b11b5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was introduced when porting the SPI driver over from u-boot but it
is not needed. Hence drop the extra typedef and use device_t instead.
Change-Id: I3ab797a8e482d1c9aa1d004e488e99aeaffcdd8b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1331
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The count was only incrementing for a wake from S5 and
it was not incrementing in the normal reboot case.
Change-Id: I73bc6db6bd02e6c4677f7e44a5c098c6dcb51747
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
MCHBAR 0x5f10[7:0] should be set to 0x30 for ivybridge
and 0x20 for sandybridge. Move this code to ramstage
and set it per-chipset.
Power Aware Interrupt Routing is supported in ivybridge,
enable it and set fixed priority.
Boot on ivybridge device and read MCHBAR 0x5f10:
mmio_read8 0xfed15f10
0x30
And verify PAIR is enabled (bit4=1):
mmio_read8 0xfed15418
0x24
Change-Id: If017d5ce2bd5ab5092c86f657434f2b645ee6613
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1303
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
CPUs with configurable TDP will run the TSC at the max non-turbo
ratio for the maximum TDP value, which can cause issues if another
TDP is desired. To deal with this we set the flex ratio to the
nominal TDP ratio early in the boot and then configure the Soft
Reset Data registers so the PCH can tell the CPU what frequency
to run at after a reset.
This is done very early in the bootblock because it is necessary
to reset the system after setting a flex ratio.
The end result is that the TSC will now increment at the max
non-turbo frequency for the nominal TDP.
On some system with 1.8GHz CPU ensure that the kernel
detects the CPU speed as ~1800mhz rather than ~2300mhz:
> dmesg | grep "MHz processor"
[ 0.004000] Detected 1795.801 MHz processor.
Change-Id: I8436dced9199003b6423186a2b041e3f7b84ab8c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are enough differences that it is worth defining the
proper map for the sandybridge/ivybridge CPUs. The state
save map was not being addressed properly for TSEG and
needs to use the right offset instead of pointing in ASEG.
To do this properly add a required southbridge export to
return the TSEG base and use that where appropriate.
Change-Id: Idad153ed6c07d2633cb3d53eddd433a3df490834
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1309
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- add Kconfig option for CONFIG_SPI_FLASH_SMM
- compile subsystem and chip drivers for smm if enabled
- change mdelay(1) to udelay(500) since mdelay is not defined
in SMM and a 1ms delay is worth avoiding
- make flash chip structure non-const so the probe function
pointers can be relocated for use in TSEG
- Make SMM PCI access possible in southbridge SPI code
Change-Id: Icfcbbe8e4e56658769d46af0b5bf6c79a6432641
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1313
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is used by the SPI driver and ELOG.
It requires SMM TSEG and a _heap/_eheap region defined in the
linker script. The first time malloc is called in SMM the
start and end pointers to the heap region will be relocated
for the TSEG region.
Enable SPI flash and ELOG in SMM and successfully
allocate memory. The allocated addresses are verified
to be sure they are within the TSEG heap region:
smm.elf:00014000 B _eheap
smm.elf:00010000 B _heap
TSEG base is 0xad000000
Memory allocated in ELOG:
ELOG: MEM @0xad018030
Change-Id: I5cca38e4888d597cbbfcd9983cd6a7ae3600c2a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1312
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is based around the SMBIOS event log specification but
expanded with OEM event types to support more specific and
relevant system events.
It requires flash storage and a minimum 4K block (or flash block
size) that should be allocated in the FMAP.
A copy of the event log is maintained in memory for convenience
and speed and the in-memory copy is written to flash at specific
points.
The log is automatically shunk when it reaches a configurable
full threshold in order to not get stuck with a full log that
needs OS help to clear.
ELOG implements the specification published here:
http://code.google.com/p/firmware-event-log/wiki/FirmwareEventLogDesign
And is similar to what we use in other firmware at Google.
This implementation does not support double-buffered flash
regions. This is done because speed is valued over the log
reliability and it keeps the code simpler for the first version.
This is a large commit and by itself it just provides a new
driver that is made available to coreboot. Without additional
patches it is not very useful, but the end result is an event
log that will contain entries like this:
171 | 2012-06-23 16:02:55 | System boot | 285
172 | 2012-06-23 16:02:55 | EC Event | Power Button
173 | 2012-06-23 16:02:55 | SUS Power Fail
174 | 2012-06-23 16:02:55 | System Reset
175 | 2012-06-23 16:02:55 | ACPI Wake | S5
Change-Id: I985524c67f525c8a268eccbd856c1a4c2a426889
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1311
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to support SPI and ELOG drivers the SMM region
needs to be able to be larger than the previous allocation
below 0x7400. Now that we have support for 4M TSEG we do
not need to live in this region.
This change adds a 16KB heap region abofe the save state area
at TSEG+64KB and moves the C handler above this.
The heap region is then available for malloc and the C handler
can grow to support flash and event log features.
While updating the memory map comment in assembly stub I also
added a pause instruction to the cpu spin lock as this was
added to the C code in latest upstream rebase.
Dump sympbols from smm.elf binary to see the new regions:
00010000 B _heap
00014000 B _eheap
00014000 T _smm_c_handler_start
0001b240 T _smm_c_handler_end
Change-Id: I45f0ab4df1fdef3b626f877094a58587476ac634
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1308
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The BWG says ivybridge current limit for PP1 is 50A.
Verify the PP1 current limit value on link device:
> echo $(( ( $(rdmsr 0 0x602) & 0x1fff ) >> 3 ))
50
Change-Id: I946269d21ef605f2525fe03993f569d69128294b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1305
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Ivybridge B0+ CPUs are capable of supporting multiple TDP levels.
This complicates the default case because now the registers that
were reporting max non-turbo ratio are reporting that value for
the highest possible TDP level.
For now this change just forces everything to use the Nominal TDP
values instead of the higher (or lower) levels.
- When building P-state tables, determine the P[1] (max non turbo)
ratio based on the Nominal ratio if available.
- Set the turbo activation ratio to the Nominal max ratio.
- Mirror the power level settings in new MCHBAR register after
they are written, which happens after BIOS_RESET_CPL is set.
- Set the current ratio to Nominal ratio at boot.
1) Verify that P-state table is generated properly with
P[0]=1801MHz (ratio 0x1C) and P[1]=1800MHz (ratio 0x12)
PSS: 1801MHz power 17000 control 0x1c00 status 0x1c00
PSS: 1800MHz power 17000 control 0x1200 status 0x1200
2) Verify power limits in MCHBAR match PKG_POWER_LIMIT:
> rdmsr 0 0x610
0x800080aa00dc8088
> mmio_read32 0xfed159a4
0x000080aa
> mmio_read32 0xfed159a0
0x00dc8088
3) Verify turbo activation ratio is set to nominal ratio:
> rdmsr 0 0x64c
0x0000000000000012
4) Check that proper ratio was set at boot on one core only:
> grep 'frequency set to' /sys/firmware/log
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
model_x06ax: frequency set to 1800
Change-Id: I592e60a7740f31b140986a8269dca91b4adbb270
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1304
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
... and don't require it to specify a cache type.
This function is only used on romcc boards, and should go away
(because all boards should be switched to CAR)
Change-Id: Ic32ca3be1afffc773c72c140e88b338d48a0c8ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Previous patches implemented stack overflow checking for the APs.
This patch builds on the BSP stack poisoning patch to implement
stack overflow checking for the BSP, and also prints out maximum
stack usage. It reveals that our 32K stack is ridiculously oversized,
especially now that the lzma decoder doesn't use a giant 16K on-stack
array.
Break the stack checking out into a separate function, which
we will later use for the APs.
CPU0: stack from 00180000 to 00188000:Lowest stack address 00187ad8
To test failure, change the DEADBEEF stack poison value in c_start.S
to something else. Then we should get an error like this:
Stack overrun on BSP.Increase stack from current 32768 bytes
CPU0: stack from 00180000 to 00188000:Lowest stack address 00180000
Separate the act of loading from the act of starting the payload. This
allows us better error management and reporting of stack use. Now we
see:
CPU0: stack from 00180000 to 00188000:Lowest stack address 00187ad8
Tested for both success and failure on Link. At the same time, feel free
to carefully check my manipulation of _estack.
Change-Id: Ibb09738b15ec6a5510ac81e45dd82756bfa5aac2
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1286
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME needs to be talked to through the PCIe memory mapped config
space.
Change-Id: Ic2c5a572a126722a08a82d95df13d11507586c6b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1284
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The function acpi_get_vdat_info() was moved to the ChromeOS
vendor code, and is no longer required to be present for each
board. Hence, remove it.
Change-Id: I3dc8dbb6119ceffa057373bad7c0058ac0d40eb8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1283
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In the short term there might be devices with Sandy Bridge CPUs
on mainboards with Panther Point PCHes. While this configuration
option is perfectly valid, coreboot currently ties Sandy Bridge to
Cougar Point and Ivy Bridge to Panther Point. One occurence is in
the ME handling code.
To make coreboot most flexible, compile both ME handlers into
coreboot and decide at runtime which one to use.
Change-Id: Icffe2930873f67c99c3f73e37e7a967f4f002b88
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1280
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- On Cougar Point there may have been stack corruption during the
ME hash verification
- On Panther Point the ME firmware hash was not passed on to the
OS
Change-Id: I73fc10db63ecff939833fb856a6da1e394155043
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Nothing is yet enabled, this is just a config skeleton change.
The MICROCODE_INCLUDE_PATH definition is going to be used by the
Makefile building the microcode blob for CBFS inclusion.
Change-Id: I7868db3cfd4b181500e361706e5f4dc08ca1c87d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1292
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Oxford PCIE Serial card has a hardcoded address at setup,
which may be moved during PCI Init. The driver re-initializes
after PCI init. Add a debug print for the new BAR address.
Initializing Oxford OXPCIe952
OXPCIe952: Class=70002 Revision ID=0
OXPCIe952: 2 UARTs detected.
OXPCIe952: Uart Bar: 0xe0800000
Change-Id: I1858d3eba09749cba3c3869060d00e621dca112a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1327
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When microcode storage in CBFS is enabled, the make system is supposed
to generate the microcode blob and place it into the generated ROM
image as a CBFS component.
The microcode source representation does not change: it is still an
array of 32 bit constants. This new addition compiles the array into a
separate object file and then strips all sections but data.
The raw data section is then included into CBFS as a file named
'microcode_blob.bin' of type 0x53, which is assigned to microcode
storage.
Change-Id: I84ae040be52f520b106e3471c7e391e64d7847d9
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1295
Tested-by: build bot (Jenkins)
When CONFIG_MICROCODE_IN_CBFS is enabled, find the microcode blob in
CBFS and pass it to intel_update_microcode() instead of using the
compiled in array.
CBFS accesses in pre-RAM and 'normal' environments are provided
through different API.
Change-Id: I35c1480edf87e550a7b88c4aadf079cf3ff86b5d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1296
Tested-by: build bot (Jenkins)
The PCIe device enable function prints when it disables a device.
The PCIe ports(bridges) use a different routine that didn't print
the message. Add it to be consistent and to provide better debug
output.
Change-Id: I8462c48e7f4930db68703f0bfb710c01c9643a98
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1326
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
It's only used on AMD based boards. Hence drop it, so we don't
accidently start using it by mistake instead of MAX_CPUS
Change-Id: Id8f522f24283129874d56e70bd00df92abe9c3cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1325
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to
"disable",
power-off, replug device -> device turns on; and similar cases).
Modelled after http://review.coreboot.org/#/c/444
Change-Id: I2b8461dff1ae085c1ea4b4926084268b4da90321
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1323
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In preparation to support CBFS hosted microcode blobs, this change
renames the wrapper include file containing the microcode to be
independent of CPU model.
Change-Id: If1a4963a52e5037a3a3495b90708ffc08b23f4c1
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1294
Tested-by: build bot (Jenkins)
The function was too eager shifting stuff around, this change corrects
the problem.
Change-Id: I4c13dbe86cb627835dae05bb74af9867c28e143d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1291
Tested-by: build bot (Jenkins)
On systems with socketed CPUs we want to be able to
drop in a Sandy Bridge or Ivy Bridge CPU without recompiling the
firmware. Hence, detect the north bridge dynamically. In order
for this to work, we need Ivy Bridge MRC and coreboot configured
for Ivy Bridge.
Change-Id: I635bef2c61d47d36a3fdd87f8ecb6e69097ba969
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1281
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We accomplish this goal by getting rid of the huge auto array in the
ram stage. This will in turn let us reduce CONFIG_STACK_SIZE.
We have to leave it on the stack in CAR as that's the simple way to
keep it private. It does not matter then as there is only one core
that is active.
Change-Id: Ie37a057ccae088b7f3bb4aab6de2713e64d96df6
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1271
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are enough subtle differences in the magic values that
it is easier to make a separate function.
This fixes a reset hang with pantherpoint chipset.
Change-Id: I02b03cb37e5fd5ee2fd62067644f0a62dc2cd26a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1322
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The function is empty (a left-over from i945) and should be removed.
Change-Id: I91e573b5e37cb9133ea1037aef7e6daf3c292864
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1290
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This enable step has been moved to the bd82x6x bootblock.
For Samsung Stumpy and Lumpy mainboards and the
Intel EmeraldLake2 reference board.
Change-Id: I5ce54f57b8e1dd732c8a5ae71d7511703de91a0e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1307
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This makes it available early in romstage without having to
worry when the different romstagse enable it.
Check for extended CMOS to be enabled in early romstage.
This is used by a later commit which uses the extended
CMOS region for stoage.
Change-Id: I9e026d48499c63d6503c2b020d4cc3047126fa93
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1306
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Convert all PCI ID lists to new scheme
- Unify code (variable names)
- add missing PCI IDs for Panther Point PCIe root ports.
Change-Id: I6357f6ebce7ddffe45a3ec642b0c594147f6134c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1301
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
With this patch it is possible to use the smbus in ramstage. The
biggest part of the patch is a simple code split into a general
part (smbus.h) and the concrete users (early_smbus.c and cs5536.c).
After the switch from romstage to ramstage the smb base address
has changed, but that is no problem as the new base address is
stored in bar0 of the ISA bridge. It could also be read via msr,
but via PCI it is simpler. I used the following patch as
reference on how to readout the new base address:
http://lists.laptop.org/pipermail/commits-kernel/2006-November/000178.html
Change-Id: I9f86a1e474368c62f9ed3a95edfb3e63117aa156
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1243
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The oxpcie ramstage code calls uartmem_init after the PCI memory
allocation, but hte function was static and didn't have a prototype.
Change-Id: Iabc1a3d248aeaed29aaaa22504defac97c572326
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1285
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
ELOG reads from RTC to build timestamp structure,
the resulting timestamp is decoded when printing events.
Change-Id: If26552074f18de5095b967b875a0ac1d815a5b31
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1302
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Right now, if we have an unknown PCH, coreboot will print something like
this:
PCH type: Unknown rev id 4
Instead, it should also print the PCI ID of the device, so we can add it
to the list of known PCHes.
Change-Id: Ib0b96e287c36d2895d1287b1734ca13d75e7985a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1287
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This is as per Intel's suggestion on how to display their name strings.
Change-Id: Ie82341305e58baa8041e50a61a11b395fa7d9582
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1298
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Dump and disassemble ACPI tables and look in _CST.
In the last entry the state was getting set to 0:
Package (0x04)
{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000000030, // Address
0x01, // Access Size
)
},
0x00000000, // State
0x0000005A, // Latency
0x000000C8 // Power
}
Now it is properly identifed as state 3:
Package (0x04)
{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000000030, // Address
0x01, // Access Size
)
},
0x00000003, // State
0x0000005A, // Latency
0x000000C8 // Power
}
Change-Id: Ie0a68606c5a43ac5fb5ba7bb9a3fef933ad67b64
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1297
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Since coreboot is running very short, we don't free memory.
Hence, drop (dummy) free()
Change-Id: I6e2737f07c6b9f73ebfad7d124b97a57cb7454a3
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1274
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This include file needs to be prevented from being included multiple
times.
Change-Id: I42e0cbe38d332b919f22e331eaf7a0251929e1dc
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1293
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
The only difference in this code on all our platforms is the array
describing the GPIOs. Hence, only keep that array in the mainboard
ChromeOS directory and move everything else to generic ChromeOS ACPI
code.
Change-Id: I9fc75842af64530c1255bea1c5f803c5316d6da6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1278
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When no valid MRC cache area is found, the mrc_cache data structure
was used without prior initialization. This sometimes caused a long
delay when booting because compute_ip_checksum would checksum up to
4GB of memory.
Change-Id: I6a0ca1aa618838bbc3d042be425700fc34b427f2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1277
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are several reasons for this:
1. It's a core setting, not a platform setting, which is bizarre. But,
we disable vmx via an SMI, and that only happens on core 0.
Hence, the code did not correctly make the same settings on all cores-
one had them disabled, the others were in an unknown state.
When (e.g.) kvm started on a vmx-enabled core, then moved to a
vmx-disabled core, the processor would reset *very* quickly.
Changing this would be messy.
2. On the CPU on link, there is something about trying to set the lock
bit that is getting a GPF.
3. It's the wrong place and time to set it. Once controlled, they can't
be changed in the kernel. The kernel is what should control this
feature, not the BIOS, as we have learned time and time again. If
somebody is in as root and can start a VM, you have a lot more to
worry about than someone starting a guest virtual machine.
Change-Id: I4f36093f1b68207251584066ccb9a6bcfeec767e
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1276
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This check got in the code when some Linux distros shipped broken linkers
around 1999.
Since then, the code around that check was changed, and it does not make
sense anymore to have this check.
Change-Id: I37c6b690d72f55c18ba4c34e8541a6a441e5e67a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1275
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't ever free memory in coreboot, hence drop spi_flash_free() and
spi_free_slave()
Change-Id: I0ca3f78574ceb4516e7d33c06ab1a58abfb3b0ec
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1273
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's not really useful anymore I guess, and it makes the log files
harder to read. Hence dropping it.
Change-Id: If4c3e8b40ae491ca527ef62f8145206960f6579d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1272
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Brevity is the soul of wit, except for error messages;
then it's a sign of witlessness. I can say this because
this error message may be my fault, although it is lost
in the 20th century code base so who knows.
Anyway, when memalign dies, it's not a bad idea to have
a lot of information about what went wrong. So instead
of the terse single bit of "something failed" this patch
changes things to be a bit more useful.
Change-Id: I8851502297e0ae9773912839ebfdf4f9574c8087
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1270
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
- The unneeded poll on non-MT force-wake bit was timing out
and causing the gma_pm_init_pre_vbios() function to exit
early so it was not preparing PM registers properly.
I changed the gtt_poll() calls to not return on timeout
unless it can't proceed so we don't see half-initialized
registers.
- RC6+ (Deep Render Standby) is not working reliably so we
can just enable RC6 in the BIOS and let the kernel decide
if it wants to enable RC6+ later.
This Kernel message is new in kernel 3.4:
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
Change-Id: I69d005ba56be8c7684a4ea1133a1d761f7c07acc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1268
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to be able to use udelay in code running on AP cores
the timer has to be initialized on the according local APICs
or the system will just hang when udelay is used.
Change-Id: I776bc96aa6d876ff2582d0c05cbc9c7611cb06b5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1267
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Use of uma_resource() in AMD northbridge code created a memory
resource marked as reserved. Such resources are removed
from system memory in write_coreboot_table().
Change-Id: Ib5e49e851d6622d8ece9d6d612e245b3962b9167
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1233
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
It's shut down, but UMA memory is not reclaimed. A later extension
could optionally do the magic register dance that allows initialization
of IGD as secondary graphics device.
Change-Id: I2a92bb71755005b886a8e1825325c678a9991bf2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1252
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Updated P state table to make frequency scaling work.
Added these CPUs: http://support.amd.com/us/Processor_TechDocs/30430.pdf
Also wrote a Python script for parsing AMD docs,
but not sure where to put it: http://pastebin.com/1dSvkXwc
Change-Id: I8f08111b73b9be551f3f59d2acb15051ccf36c1e
Signed-off-by: Jukka Rantala <jukka.rantala@gmail.com>
Reviewed-on: http://review.coreboot.org/1244
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We were handling vga, vga_first, vga_last, vga_onboard just to determine
an onboard chip and the first plugin card.
We were also traversing the devices manually instead of using the utility
functions we have, for the chance that there are non-VGA cards we need to
cope with (but why would they require VGA-style handling?)
Change-Id: I8aa73aefa102725a64287f78a59de3d5dda1c7f2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1255
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
VGA is this part-legacy thing that can cause trouble...
For this, introduce device_t->disable(dev) method, in which a driver
can take care to deregister the device if necessary.
Change-Id: I3fecec07f402e530458b79eda30b2c274101fefa
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1251
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
A new Kconfig option tells YABEL to succeed on write accesses
on other devices' config space without performing the actual
write.
This is enough for some basic bus modification done by some
Option ROMs.
Change-Id: Iab04f3a5c350b96654da4ba26858037f4c4b5c0a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1249
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It defaults to true, and isn't disabled anywhere in the tree.
I also couldn't think of a case where it's actually useful.
Change-Id: I126a47625d5294f3cfff225629f2a948a83c9b7e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1250
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove the menuconfig warning which comes up every time.
src/mainboard/asus/Kconfig:85:warning: multi-line strings not supported
Change-Id: I0ec0a0b625a33edd1d9b250a26aa3e0f42142eca
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1240
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
One could not pass a device of type APIC to PCI resource functions.
The correct CPU model specific cpu->ops is set at later time in
cpu_initialize().
Change-Id: Ifa274185e4db3080433c1f07e3a48f2b55c0514f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1180
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Northbridge code incorrectly adjusted the last cacheable memory
resource to accomodate room for UMA framebuffer. If system had
4GB or more memory that last resource is not below 4GB and not
the one where UMA is located.
There are three consequences:
The last entry in coreboot memory table is reduced by uma_memory_size.
Due the incorrect code in northbridge code state.tomk,
end of last resource below 4GB, had not been adjusted.
Incrementing that by uma_memory_size diverts a region
possibly claimed for MMIO to RAM, as TOP_MEM is written.
Since the UMA framebuffer did not have IORESOURCE_CACHEABLE,
it was ignored from the MTRR setup and not set uncacheable.
The setting of TOP_MEM and TOP_MEM2, as well as all the MTRRs,
should be copied from BSP to all APs instead of deriving the data
separately for each Logical CPU.
Change-Id: I8e69fc8854b776fe9e4fe6ddfb101eba14888939
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1217
Tested-by: build bot (Jenkins)
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use state.tomk to refer TOP_MEM, largest RAM address below 4GB.
Use state.tom2k to refer TOP_MEM2, largest RAM address above 4GB.
When setting either TOP_MEM or TOP_MEM2, any RAM resource found
must fit below the set value. Thus, round register value upwards,
not downwards.
Change-Id: I436c1b3234c911680ce8b095052f8d71f40113e2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1216
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
If northbridge called uma_resource() a resource of this type
should be found when walking the resources list.
For now, be rude and don't even try to combine it with
neighboring regions. As the type is un-cacheable it is
dominant over other MTRR setups claiming the same region.
Change-Id: I57805e7e7da0709f8ed78d8df62c2abf22172a06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1215
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
MTRR setup code can detect this and mark it as UC/WT/WC as suitable
for the specific hardware.
Change-Id: Ib7a3d450fc7c19e3ca72767dfb350412dd35c971
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1214
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These boards had identical UMA code:
amd/dbm690t
amd/pistachio
technexion/tim5690
technexion/tim8690
The ones below had whitespace or debug level change
compared to the one above:
kontron/kt690
siemens/sitemp_g1p1
These boards use AMDFAM10 guidelines in code:
asrock/939a785gmh
amd/mahogany
Change-Id: Id7c3f48035727f5847f2d7c3a6e87a3d15582003
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1210
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
advansus/a785e-i
amd/bimini_fam10
amd/mahogany_fam10
asus/m5a88-v
avalue/eax-785e
gigabyte/ma78gm
iei/kino-780am2-fam10
jetway/pa78vm5
Following boards had identical code:
amd/tilapia_fam10
asus/m4a78-em
asus/m4a785-m
gigabyte/ma785gm
gigabyte/ma785gmt
In between the two, only whitespace difference.
Change-Id: Iaa48cc7b0038ebcc81be49219b4fc87670aa9941
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1209
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
amd/inagua
amd/persimmon
The following had only whitespace or debug level changes
compared to ones above.
amd/union_station
amd/south_station
asrock/e350m1
Change-Id: I11ee46e06e1dd510cba551166189ebcaa144464b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1208
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Like ram_resource(), but reserved and not cacheable.
Switch all AMD northbridges to use this one.
Change-Id: I88515c6a0f59f80fd8607c390d0d4a2a35d805f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1203
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current code didn't reserve static resource the right way.
Also reduce TOLM to 0xd0000000, because those boards have so many PCI
devices that 0xe0000000 isn't sufficient.
Change-Id: Ia75a81905eea1a096aed464b63ac154e044bc99c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1220
Tested-by: build bot (Jenkins)
Code can easily make the mistake of using uninitialized
values or, in assembly, mistakenly dereferencing stack pointers
when an address is desired.
Set the stack to a non-zero value which is also (by testing)
a pointer which will crash coreboot if used. This poisoning
has uncovered at least one bug.
Change-Id: I4affb9a14b96611e8bf83cb82636e47913025a5d
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1221
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
And fix the wrong indenting of devicetree.cb while at it.
Change-Id: Idbb19fb5d7155f44675098e79920caf65191c239
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1222
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Hudson code has been integrated from CIMx to AGESA. This patch is about the wrapper.
Change-Id: I63d951982140b82a3a77a97eb3d55fc75fc0caa3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1157
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Linux boots fine :)
Change-Id: Ifda06e5220666534b87f528deae16d8b956c32b3
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1225
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch adds support for autogenerating the MPTABLE from
devicetree.cb. This is done by a write_smp_table() declared
weak in mpspec.c. If the mainboard doesn't provide it's own
function, this generic implementation is called.
Syntax in devicetree.cb:
ioapic_irq <APICID> <INTA|INTB|INTC|INTD> <INTPIN>
The ioapic_irq directive can be used in pci and pci_domain
devices. If there's no directive, the autogen code traverses
the tree back to the pci_domain and stops at the first device
which such a directive, and use that information to generate the
entry according to PCI IRQ routing rules.
Change-Id: I4df5b198e8430f939d477c14c798414e398a2027
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1138
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Missed to add the driver to Kconfig and Makefile.inc.
Change-Id: I64b02abc5de2f6483f610436ebb38a7ca433f9b6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1219
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
All but one board use the default value of enabled. Disabling
this can only increase the number of MTRR registers used.
Change-Id: I7d28adc31b9fae2301e4ff78fcb96486f81d5ec2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are two errors in the code. The first one is a missing
$ sign in mov _stack, %esp. Thanks to Ronald G Minnich for
catching that bug.
The second bug is the 'incl %eax', which shouldn't be there, as
there's no secondary CPU with index 0. CPU0 uses always the stack
below _estack.
Change-Id: Id267a654ba95b0e898eeaaafb2403b438250a563
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If a CPU was pre-allocated, cpu_path is not copied and thus
index would not be updated. This breaks cpu_index() and AMD
model_fxx is possibly broken without this patch.
Change-Id: I77483181cf0bca31423c655942c022bffab3c7ea
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1199
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
If threads called alloc_find_dev() with same device_path
simultaneously, two device nodes could be allocated.
This bug is not triggered by current code.
Change-Id: Ifc87021c8d6f422901c5de5dd17392e3e2309afa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Not all users use both functions, so add __attribute__((unused))
to prevent compiler errors.
Change-Id: I8485bb9150b04d1f9fdc231152a43bcd6fc713a7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1193
Tested-by: build bot (Jenkins)
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Implements support code for talking to IPMI hardware that uses
a KCS style interface.
Change-Id: I9895cc1bf29676115b167081b63b8a430e23eee5
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1190
Tested-by: build bot (Jenkins)
The Kconfig file for this board contains a bogus option called
CORE_GLIU, this change removes it.
Change-Id: I4ea069bdd76be53085ebc9c0fb3dd71ffb2a12e1
Signed-off-by: Ricardo Martins <rasmartins@gmail.com>
Reviewed-on: http://review.coreboot.org/1179
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
PCI Type 2 config was a strange and never-used config mechanism.
It is unlikely that in the 13 years of coreboot's existence that
type 2 was ever used; it just made life complicated for everyone.
It lived long enough in coreboot to be replaced by mmioconf.
Prior to making the device tree visible in romstage we want to
get rid of type2.
Delete two files we don't need any more (yay!).
Replace two functions with one: pci_config_default, which returns
a pointer to the default config method. At some future time this
may change to mmio but for now it is old type1 style.
Change-Id: Icc4ccf379a89bfca8be43f305b68ab45d88bf0ab
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1159
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The SIPI vector copy can use a static location below 1MB, aligned
to 4kB. Jump out of the copy once in protected mode.
Change-Id: I6299aa3448270663941cf2c4113efee74bcc7993
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1165
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
CACHE_ROM_SIZE default is ROM_SIZE, the Flash device size set
in menuconfig. This fixes a case where 8 MB SPI flash MTRR setup
would not cover the bottom 4 MB when ramstage is decompressed.
Verify CACHE_ROM_SIZE is power of two.
One may set CACHE_ROM_SIZE==0 to disable this cache.
Change-Id: Ib2b4ea528a092b96ff954894e60406d64f250783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1146
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Diff between model_106cx and model_6ex CAR codes suggests currently
used model_106cx CAR is not optimal - destination RAM and source ROM
of ramstage copy_and_run are only partly set cacheable.
It appears variable MTRR setting for XIP cache is left enabled on
model_106cx code, where it should have extended to cover all of Flash.
Introduces untested functional change on boards:
intel/d945gclf
iwave/iWRainbowG6
Deletes file:
model_106cx/cache_as_ram.inc
Change-Id: I35229f8433927e83821e72e9d9a9fc8fb09c3f1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/642
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
A diff from model_6fx to model_106cx suggests there is little
CORE2 specific code that was once considered useful to have.
In its current status however, sockets supporting model_6fx use
model_6ex CAR init, so that specific code is actually
never used.
Deletes file:
model_6fx/cache_as_ram.inc
Change-Id: I6c0204446fa98207e31f91895e1cf30fde42382c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/640
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Used for automatic generation of IOAPIC interrupt entries.
Change-Id: Ia746f01906c840800956ce551306f864e440b6ec
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1137
Tested-by: build bot (Jenkins)
Default CPU_ADDR_BITS is 36.
For Atom (model_106cx) use 32. This model is known to
fail execution-in-place (XIP) with the default 36.
Pentium M should use 32, but doesn't even with this patch.
Some Xeon and CORE(2) models should use 38 or 40.
Change-Id: If604badcdc578c4f4bc7d30da2f61397ec0d754c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/639
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
used for fan control and thermal management on that board.
Change-Id: I4e5c986ab6174b7a356d682e21732c46181af211
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1167
Tested-by: build bot (Jenkins)
awk on Cygwin created the UTF-8 value for the 0xff code point,
which makes it two bytes wide. This broke the build.
Change-Id: I4937ae7ce1136ba7a76d05b42f9dd2771203175d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1164
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
With this change it is possible to define serial number
and version of the mainboard. These informations are used
in SMBIOS tables.
Change-Id: I1634882270f6cb94e00aceb7832e7fd14adc186b
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1163
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The error message from romstage is annoying and misleading:
"Do not use global variables in romstage"
Because it can occur even when global variables are not used
in some circumstances, but also because it gives you only a rough
idea where to look. This change sucks but sucks less. We still don't
know which file the problem is in but at least we know if it is data
or bss.
Replace the error message with something that provides more information
and less guessing on the part of the script:
".bss is non-zero size in romstage which is not allowed -- global variable?"
or
".data is non-zero size in romstage which is not allowed -- global variable?"
To test: build coreboot as normal. It builds.
Add
char d[32];
to romstage.c and get the first error message; add
int x = 32;
to romstage.c and get the second.
Change-Id: I300ec05bdb4b30d7ef3f5112e6cc09b1fafe8263
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1160
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The new broadcast code doesn't support serial init - if a CPU
needs serial init, this should be handled in the model specific CPU
init code.
Change-Id: I7cafb0af10d712366819ad0849f9b93558e9d46a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1140
Tested-by: build bot (Jenkins)
The current code for initializing AP cpus has several shortcomings:
- it assumes APIC IDs are sequential
- it uses only the BSP for determining the AP count, which is bad if
there's more than one physical CPU, and CPUs are of different type
Note that the new code call cpu->ops->init() in parallel, and therefore
some CPU code needs to be changed to address that. One example are old
Intel HT enabled CPUs which can't do microcode update in parallel.
Change-Id: Ic48a1ebab6a7c52aa76765f497268af09fa38c25
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Early HT-enabled CPUs do not serialize microcode updates within a core.
Solve this by running microcode updates on the thread with the smallest
lapic ID of a core only.
Also set MTRRs once per core only.
Change-Id: I6a3cc9ecec2d8e0caed29605a9b19ec35a817620
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1142
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
They used MP_IRQ_TRIGGER_LEVEL, but it should be MP_IRQ_TRIGGER_EDGE.
While at it, uses mptable_lintsrc() instead.
Change-Id: Ie71311b8bf865889cf0d8808467df98af4b0132d
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1136
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This adds basic supported for the Supermicro X7DB8. Basic means that
almost all onboard peripherals are working. Known problems are:
- mptable needs to be written dynamically. If you plan to use Add on
cards, modify mptable.c according to your needs. A patch to add generic
mptable autogeneration based on devicetree is coming up.
Change-Id: I5eaac32a8bafa69a05929cf08d869127b9464661
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/493
Tested-by: build bot (Jenkins)
Required for Supermicro X7DB8, which needs the FBDIMM clock generator
setup during romstage.
Change-Id: I30ca8354087e851487aee0614595782131d4d9bc
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1116
Tested-by: build bot (Jenkins)
Here's a quick demonstration on how to use it(tested on M4A785T-M).
(gdb) file ./build/cbfs/fallback/coreboot_ram.debug
Reading symbols from [...]/build/cbfs/fallback/coreboot_ram.debug...done.
(gdb) set remotebaud 115200
(gdb) target remote /dev/ttyUSB0
Remote debugging using /dev/ttyUSB0
_text () at src/arch/x86/lib/c_start.S:85
85 call hardwaremain
Change-Id: Ia49cbecc41deb061433bc39f5b81715da49edc98
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/1134
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
i3100/i5000 have a second IOAPIC which handles IRQs for PCI-X.
Add code to enable it.
Change-Id: Ib447628f501b152c8adc9c7c89bd09b5615b9e5a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1118
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The constant value 0x100000000 is used in linker scripts to calculate
offsets from the end of 32-bit-addressed memory. There is nothing
wrong with it, but 32-bit versions of ld do the calculation wrong.
Change-Id: I4e27c6fd0c864b4d98f686588bf78c7aa48bcba8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1129
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
As Mathias Krause pointed out, using movw/outw on %al is clearly invalid.
Let's do another typo fix...
Change-Id: Ib95832a11097f599a236ab30c64c26ef429a1699
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1119
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Peter and Ron pointed out two typos. They have no side effects, but
it's still worth to fix them.
Change-Id: I9aecccdbc72beb2623fbe558a06e4f1b050f6e74
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1117
Tested-by: build bot (Jenkins)
Those CPUs support the PECI (Platform Environment Control
Interface), so enable it. This interface is commonly used
for tasks like fan control.
Change-Id: Id2dadc4821de8cc0b579e77235aa36892e57fd02
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1104
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Not doing a hard reset leaves the BOFL0 register cleared, which
prevents the BSP selection from working. To make sure we start
with known values, use the SPAD0 register for soft reset detection.
If there's a value other than 0, do a hard reset.
Change-Id: I390e3208084cfd32d73cce439ddf2bc9d4436a62
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1103
Tested-by: build bot (Jenkins)
Without that fix we have:
LINK cbfs/fallback/romstage_null.debug
build/generated/crt0.romstage.o: In function `ramtest':
romstage.c:(.rom.text+0x53f): undefined reference to `.Lhlt'
collect2: ld returned 1 exit status
make: *** [build/cbfs/"fallback"/romstage_null.debug] Error 1
On the M4A785T-M which doesn't have CONFIG_ROMCC.
Change-Id: I49eded1d18e996afe9441b85dae04ae30c760dd6
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/1101
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
- Add #define to allow the FADT PM Profile to be overridden.
- Change the location of the PMA_CNT_BLOCK_ADDRESS to match
current documentation.
- cst_cnt should be 0 if smi_cmd == 0
- add a couple of default access sizes.
- Add a couple of #define values for unsupported C2 & C3 entries.
- Add PM Profile override value into amd/persimmon platform.
This does not use the #defines in acpi.h so that the files that
include this don't all need to start including acpi.h.
Change-Id: Ib11ef8f9346d42fcf653fae6e2752d62a40a3094
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1055
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
commit 5b6404e419 ("Fix timer frequency
detection on Sandybridge") reworked the udelay code, but didn't add
the 333MHz FSB entry used on Model 15 Xeons.
Change-Id: Ie34f9ae3703b64672625e7bf1b943654a7a5eaa6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1099
Tested-by: build bot (Jenkins)
It is just me or does anybody have the same build error without
this patch?
------
src/arch/x86/boot/acpigen.c: In function 'acpigen_write_empty_PTC':
src/arch/x86/boot/acpigen.c:347:3: error: unknown field 'resv'
specified in initializer
src/arch/x86/boot/acpigen.c:347:3: warning: missing braces around
initializer
src/arch/x86/boot/acpigen.c:347:3⚠️ (near initialization
for 'addr.<anonymous>')
-------
Anyway, I believe at least this will cause warnings.
"resv" is a member of a union, not of acpi_addr_t. So it should be
wrapped by a brace in the initializer.
Change-Id: I72624386816c987d5bb2d3a3a64c7c58eb9af389
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1056
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Without that fix the debugging is harder because the person debugging
coreboot will see the following twice(note the repeated MTRR number):
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
[...]
Setting variable MTRR 1, base: 4096MB, range: 512MB, type WB
Setting variable MTRR 1, base: 4608MB, range: 256MB, type WB
Setting variable MTRR 1, base: 3072MB, range: 1024MB, type UC
instead of the following twice:
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
[...]
Setting variable MTRR 1, base: 3072MB, range: 1024MB, type UC
Thanks to kmalkki on #coreboot's Freenode IRC channel for the idea:
May 25 23:57:17 <kmalkki> I would add (move) that "Setting variable MTRR..." debug at the end of set_var_mtrrs()
Change-Id: I9f4b7110ba34d017a58d8cc5fb06a7b1c3d0c8aa
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/1058
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds utility functions which allow to read any GPIO pin,
as well as a vector of GPIO pin values.
As presented, these functions will be available to Sandy Bridge and
Ivy Bridge systems only.
There is no error checking: trying to read GPIO pin number which
exceeds actual number of pins will return zero, trying to read GPIO
which is not actually configured as such will return unpredictable
value.
When reading a GPIO pin vector, the pin numbers are passed in an
array, terminated by -1. For instance, to read GPIO pins 4, 2, 15 as a
three bit number GPIO4 * 4 + GPIO2 * 2 + GPIO15 * 1, one should pass
pointer to array of {4, 2, 15, -1}.
Change-Id: I042c12dbcb3c46d14ed864a48fc37d54355ced7d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1049
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
clang does its own linking, incompatible to our
binutils-centric linker magic.
Change-Id: I243597adcb6bc3f7343c3431d7473610c327353d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/785
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It's only used in the ACPI generator for Sandybridge/Ivybridge CPUs
and the code can easily be changed to not rely on any Kconfig magic.
Change-Id: Ie2f92edfe8908f7eb2fda3088f77ad22f491ddcf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1047
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Right now coreboot compilation fails when SPI flash debugging is
enabled. Fix it by using the right set of memory functions.
Change-Id: I5e372c4a5df53b4d46aaed9e251e5205ff68cb5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1044
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Experiments have shown that writing plain value of 6 at byte io
address of 0xcf9 causes the systems to reset and reboot reliably.
Change-Id: Ie900e4b4014cded868647372b027918b7ff72578
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1050
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Originally, on ChromeBooks, coreboot would provide a modified
u-boot device tree (FDT) to u-boot in CBMEM. However, u-boot
can now create all the information it needs from the coreboot
table and add it to its device tree itself. This means we can
drop this (anyways unused) code.
Change-Id: I4ab20bbb8525e7349b18764aa202bbe81958d06a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1052
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Originally, ChromeBooks would get the offset of the MRC cache
from an entry in the u-boot device tree. Not everyone wants to
use u-boot on Sandybridge systems, however.
Since the new code (based on Kconfig) is now fully working, we
can drop the u-boot device tree remnants.
Change-Id: I4e012ea981f16dce9a4d155254facd29874b28ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1051
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The MRC region is described by Kconfig variables, no further math
or parsing is required at this point.
Change-Id: I290d8788b69ef007e9ea2317ce55aefa2d791883
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1046
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Without this option bluetooth configuration value in nvram is not
consulted properly.
It also enables built-in volume control (read-only).
Tested on: ThinkPad X60s, 1702.
Change-Id: I2fc6bb527c6e086a083e63922d1253eda7d4a36d
Signed-off-by: Motiejus Jakštys <desired.mta@gmail.com>
Reviewed-on: http://review.coreboot.org/985
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The SPI drivers from u-boot make heavy use of %zu/%zd (size_t/ssize_t).
Implement this in our printk implementation so we get useful output.
Change-Id: I91798ff4f28b9c3cd4db204c7ec503596d247dcd
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1043
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
A while back coreboot was changed to read the subsystem IDs from
devicetree.cb to allow each onboard PCI device to have its own
subsystem id. When we originally branched, this was not the case,
and the sandybridge/ivybridge mainboards have not been updated yet.
Also, drop the subsystem ID from Emerald Lake 2, since it's not a
Google device.
Change-Id: Ie96fd67cd2ff65ad6ff725914e3bad843e78712e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1042
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Only print PP: lines if CONFIG_DEBUG_SPI_FLASH is enabled.
Change-Id: If25e916ecb585f37c90d42980e933a6cd1a3d956
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1045
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Kyösti Mälkki