SMI1 is being written to but never read from.
Change-Id: I82c0800713e3093eb1317b5e1f6f228771134857
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6808
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This matches what was done on baytrail in commit bfca984b -
soc/intel/fsp_baytrail: set up for including irqroute.h twice
irq_helper.h intentionally gets included into irqroute.asl twice - once
for pic mode and once for apic mode. Since people are used to seeing
guard statements on the .h files, add the guards to irqroute.h and add
a comment to irq_helper.h explaining why they aren't there.
Change-Id: I709f9370ce7db1b3ffac2297aeaba5cc670ec20c
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6606
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Also move it to NB to be in line with other.
Change-Id: Ibd961d60dcd686899f34f6a494c14ff9d65e618b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6625
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The GPIO controller uses IRQ14 as an active high level triggered
source for GPIOs that are configured to trigger shared interrupt.
This was also tested on bolt by configuring the touchscreen to use
a shared GPIO interrupt:
localhost ~ $ grep atmel_mxt_ts /proc/interrupts
54: 24 188 93 124 LP-GPIO-demux atmel_mxt_ts
Change-Id: I3765120112bae11407e5b2020399d0d0b8e3cef8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171901
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 63a0c80ce5a19410d0608fede5a9fe0ec1c8e5c1)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6541
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
As a follow up to #6479 (63e1948643),
fix the remaining faulty loop.
Change-Id: I2c77efe620c71e939f4d74e48f90a166c782e5f5
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6569
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Some copy-pasta snuck in that reintroduced an error
already fixed in #3435 (62f8083dfd)
Change-Id: I47db23e88fa09c73b4cf3e99fe2d0ed2ac30fd80
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6479
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
This adds the southbridge initialization pieces for Intel's Atom C2000
processor (formerly Rangeley). It is intended to be used with the Intel
Atom C2000 FSP and does not contain all of the pieces that would
otherwise be required for initialization.
Change-Id: I416e85bd6e9c9dcf79f97785074135902fdd18b7
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/6370
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Needed to be able to choose convenient usbdebug port.
Change-Id: I84b304f0f8fa79cc8d4a136ee6d78dc7659601c9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6410
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Based on damo22's work and my X230 tracing.
Works for my X230 in a variety of RAM configs.
Also-By: Damien Zammit <damien@zamaudio.com>
Change-Id: I1aa024c55a8416fc53b25e7123037df0e55a2769
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/5786
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Currently `IFD_BIN_PATH` is shown twice. Commit 5218e616
(intel/lynxpoint: Allow building without IFD (descripter.bin)) [1]
accidentally added the option another time.
So fix up the commit and remove one of the two options `IFD_BIN_PATH`.
Keep the one which depends on `!HAVE_IFD_BIN` and is around the IFD
options.
[1] http://review.coreboot.org/6046
Change-Id: Id46f01ab8ee2e752e337e687a2ef0dfa374f44a5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6269
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
SPI controllers in Intel and AMD bridges have a slightly different
restriction on how long transactions they can handle.
Change-Id: I3d149d4b7e7e9633482a153d5e380a86c553d871
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6163
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
This change makes it possible for vboot to avoid an
exploit that could cause involuntary switch to dev mode.
It gives depthcharge/vboot some information on the
type of input device that generated a key.
BUG=chrome-os-partner:21729
TEST=manually tested for panther
BRANCH=none
CQ-DEPEND=CL:182420,CL:182241,CL:182946
Change-Id: I87bdac34bfc50f3adb0b35a2c57a8f95f4fbc35b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://chromium-review.googlesource.com/182357
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Tested-by: Luigi Semenzato <semenzato@chromium.org>
Commit-Queue: Luigi Semenzato <semenzato@chromium.org>
Reviewed-on: http://review.coreboot.org/6003
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This will make USB keyboards connected to USB3 ports work
in libpayload on Beltino.
BUG=chrome-os-partner:23396
BRANCH=none
TEST=Use USB keyboard on Beltino in dev mode screen
Change-Id: I70b03d733bd9e4c8be5673b48bd2196effa8a5e7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/173640
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
[pm: rebase to master branch of coreboot upstream]
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6018
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When USB3 devices are attached while in suspend, or two USB3 devices
that are both plugged in are switched to the other port while in
suspend the kernel does not seem to notice this -- despite the cold
attach status bit. This results in the devices showing up in the USB
list at the old enumerated device numbers and higher layers continuing
to think they are present but not reseponding.
With the kernel workaround to deal with devices that are logically
disconnected it is possible for firmware to send a warm port reset to
devices that are in this state and then the kernel will see them disappear
and handle it properly.
This same issue exists in the EFI firmware on the Whitetip Mountain 2
reference board so it is not specifically a coreboot bug. If this
behavior is fixed in the kernel then this workaround could be removed
since it is in RW firmware.
BUG=chrome-os-partner:22818
BRANCH=falco,peppy,wolf,leon
TEST=manual:
1) attach two USB3 devices
2) suspend system
3) switch the ports that the USB3 devices are attatched to
4) resume system
5) confirm that the devices are re-enumerated and come up properly
Original-Change-Id: Ifba3ffc94a06dc0b2436d7d7d464d824657362af
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170335
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 203d200268f4af6445224962190cbc66ad2a83e4)
Change-Id: I54fd2847ee25a60f25c2cefebdc1a3c18455464a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170579
[pm: rebase to master branch of coreboot upstream]
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6017
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
I have been attempting to work around USB3 issues that appear in the
kernel with hacks in the firmware, but this is resulting in more
headaches in the kernel.
Instead remove all the work that was being done at resume time and undo
the change that was issuing a warm reset to all ports at suspend time.
The bad device behavior will be dealt with at the kernel level to
handle devices that get stuck in polling state after enable/disable
sequence.
BUG=chrome-os-partner:22754
BRANCH=falco,peppy,wolf,leon
TEST=manual:
suspend/resume with several misbehaving devices:
Kingston USB3 Media Reader
Transcend USB3 Media Reader
Various ADATA USB3 drives
Various Kingston USB3 sticks
Original-Change-Id: I0894454af42d2ced456fe0da921d74c9e74902d0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170107
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit c2abb4d0dad6ed00e1e230d604c4c0a76eb4eef7)
Change-Id: Ib215d9c230f90a1c9f34bf29254bb9feec28c67e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170578
[pm: rebase to master branch of coreboot upstream]
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6016
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Whenever spi_xfer is called and whenver it's implemented, the natural unit for
the amount of data being transfered is bytes. The API expected things to be
expressed in bits, however, which led to a lot of multiplying and dividing by
eight, and checkes to make sure things were multiples of eight. All of that
can now be removed.
BUG=None
TEST=Built and booted on link, falco, peach_pit and nyan and looked for SPI
errors in the firmware log. Built for rambi.
BRANCH=None
Change-Id: I02365bdb6960a35def7be7a0cd1aa0a2cc09392f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/192049
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
[km: cherry-pick from chromium]
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6175
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The spi_flash_probe and and spi_setup_slave functions each took a max_hz
parameter and a spi_mode parameter which were never used.
BUG=None
TEST=Built for link, falco, rambi, nyan.
BRANCH=None
Change-Id: I3a2e0a9ab530bcc0f722f81f00e8c7bd1f6d2a22
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/192046
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
[km: cherry-pick from chromium]
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6174
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This is needed to successfully build fox_wtm2 from external repo.
BUG=chrome-os-partner:18638
BRANCH=none
TEST=manual: successfully compile coreboot for fox_wtm2 and
create an image with chromeos-bootimage/cros_bundle_firmware
Change-Id: Iaa4e9983faa1d86c2b29d8fd4f577be035497e38
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48676
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4132
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some USB3 devices are not showing up after suspend/resume cycles.
In particular if a device uses a lower power state like U2 it may
take longer to come up and the firmware needs to wait after sending
a warm port reset.
In addition skipping port reset to connected ports in the way into
suspend was causing problems so instead send all ports a reset
before suspend.
BUG=chrome-os-partner:22402
BRANCH=falco,peppy,leon,wolf
TEST=manual:
Suspend/resume with ADATA HE720 HDD (and other devices) both
connected at suspend and connecting while in suspend and ensure
that the devices always show up in the kernel.
Change-Id: Ib7b15dc65792742b4ceb7dcfc4b2c83192eafcc2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169548
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/6015
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In order to enable a Super I/O in non Chrome EC systems we
need to make pch_enable_lpc() available to the mainboard
romstage.c
BUG=none
BRANCH=none
TEST=boot ChromeOS on Beltino
Change-Id: I34e7d23012e1852c69e82ba7cdc81a05751846de
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172180
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/6019
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add the chip option to disable SATA DEVSLP. This disables
the SDS bit in the SATA CAP2 register.
BUG=chrome-os-partner:23186
BRANCH=leon
TEST=Manual: System runs without SATA failure for more than 10 hours
Original-Change-Id: I8baa40935421769aeee341a78441fb19ecaa3206
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: https://chromium-review.googlesource.com/174648
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
(cherry picked from commit 49d25812b04a983d687a53a39530559ba99fd9b4)
Change-Id: Iac0b32f80958f5ffb571733484dc931bee216f55
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: https://chromium-review.googlesource.com/176352
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/6013
Tested-by: build bot (Jenkins)
This will allow the legacy mode boot path to leave USB
ports routed to EHCI so they can be used by SeaBIOS.
BUG=chrome-os-partner:22085
BRANCH=falco,peppy
TEST=manual: Build and boot from USB and SeaBIOS on falco
Change-Id: I46870eccd1b846dc8a7f8d7948969c8e623e18cd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66547
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/6011
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Current build configuration always wants to include an Intel Management Engine
(ME) firmware (`me.bin`) on Intel Lynx Point systems. However, we can have a
working coreboot without it, as long as the factory delivered ME firmware is
kept untouched in the flash ROM. So let the user decide if a ME firmware will
be included in the build by introducing the Kconfig option `HAVE_ME_BIN`.
The same was done in commit 99fd30e4 (sandybridge: Make inclusion of me.bin
optional) [1] for Intel Sandy Bridge (BD82x6x).
[1] http://review.coreboot.org/3522
Change-Id: I7c6048fd0f56288769ad90acbfb67b908ac8d824
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6047
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
On newer Intel systems, like Intel Lynx Point, the flash ROM is shared
between the host processor (BIOS), its Management Engine (ME) and an
integrated Ethernet controller (GbE). The layout of the flash ROM (and
other information) is kept in the so called Intel Firmware Descriptor
(IFD). If we only want to build coreboot to update the BIOS section,
all we need is the flash layout.
So add the option to specify the flash layout in the mainboard’s
Kconfig, and thus, to build without the real IFD. However, with such a
build, one has to make sure that the IFD section on the flash ROM will
not be written over (nor any other section that has not been included
by coreboot). A patch to write selected sections of a flash ROM with
IFD has been sent to the flashrom mailing list [2].
The same was done in commit a15cd66b [1] (sandybridge: Make build
possible without descriptor.bin) for Intel Sandy Bridge (BD82x6x).
[1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html
[PATCH] Add option to read ROM layout from IFD
[2] http://review.coreboot.org/3524
Change-Id: I26a604446cdf37a6bbcee2b14a107b7ccf417d5c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6046
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Move some __SMM__ functions under the #if preprocessor condition to
avoid warnings about unused functions.
Change-Id: I7f6fbc6a577032bc4e4635d91e8e94aecb517bd3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6127
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This existed for ChromeOS but was no longer used with DYNAMIC_CBMEM.
Change-Id: I558a7ae333e5874670206e20a147dd6598a3a5e7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6032
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
There are a couple of places where CPPFLAGS are
pasted into CFLAGS, eliminate them.
Change-Id: Ic7f568cf87a7d9c5c52e2942032a867161036bd7
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5765
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Rename INCLUDES to CPPFLAGS since the latter is more
commonly used for preprocessor options.
Change-Id: I522bb01c44856d0eccf221fa43d2d644bdf01d69
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5764
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
CPU - fsp_model_206ax:
- Remove Kconfig options and mark this as using the FSP.
- Use shared FSP cache_as_ram.inc file
Mainboard - intel/cougar_canyon2:
- Update to use the shared FSP header file.
- Modify to call copy_and_run() directly instead of returning to
cache_as_ram.inc.
Northbridge - fsp_sandybridge:
- remove mrccache, fsp_util.[ch]
- add fsp/chipset_fsp_util.[ch] with chipset specific FSP bits.
- Update to use the shared FSP header file.
These changes were validated with FSP:
CHIEFRIVER_FSP_GOLD_001_09-OCTOBER-2013.fd
SHA256: e1bbd614058675636ee45f8dc1a6dbf0e818bcdb32318b7f8d8b6ac0ce730801
MD5: 24965382fbb832f7b184d3f24157abda
Change-Id: Ibc52a78312c2fcbd1e632bc2484e4379a4f057d4
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5636
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
GP0e does not fit into the naming scheme of the field units surrounding
this field unit definition. Also the keys for e and 3 are close to each
other supporting the theory that this is indeed a typo.
Change-Id: I43cf288fe1e0240b33971073c1aa8a1db5762e31
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5483
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The SerialIO DwordIo() definition is fixed up before returning
it in the serialio device _CRS method, so the values that are set
in the raw ASL are not actually used.
However modern versions of IASL do not like that the RangeLength is
set to zero and will fail to compile. Set this value to 1 to make
IASL stop complaining, but the real value is still fixed up in _CRS
so this has no real effect on the end result.
Change-Id: Iceb888e54dd4d627c12d078915108a11f45b1a2d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
SPI registers didnt change since ICH8. No need to have separate
files for them. Unify.
Change-Id: I4e2ac3221b419c007e135c9ee615fc3b84424cbc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5254
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Without this memory decoding isn't activated which, in turn,
makes SeaBIOS crash.
Change-Id: I3dcc721b500ab7468e1082157eeeed38044462d0
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5326
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
With generic load using 32-bit accesses this is no longer has a
huge impact it previously did. It's also unnecessarily
component-speficific.
Change-Id: I7e8a74ea1ceaa225e1024f9eb43e7280773e2b5a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5131
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Properly determine temperature target and set it in early
init rather than hardcoding it in late init.
Change-Id: Ie763f205890674a9dd1d9c5974caaccdd67cea14
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5264
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Chrome OS environment sends an SMI to finalize the chipset/board
at the end of the "depthcharge" payload, but there is no facility to
send this command if not using the full ChromeOS firmware stack.
This commit adds a callback before booting the payload that will
issue this SMI which will lock down the chipset and route USB devices
to the XHCI controller.
Change-Id: I2db9c44d61ebf8fa28a8a2b260a63d4aa4d75842
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5181
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This sequence was derived from BD82X6X and on ibexpeak it inadvertently
disables interrupts. In older kernels it wasn't a problem but in new kernel
it makes codec probe fail.
Change-Id: I40184ae8c4cfe758869af1a1565b88f0a238150e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5074
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Remove the bit of code that was putting the SerialIO devices into
D3Hot state when they are switched from PCI to ACPI mode. Instead,
add the appropriate ACPI Methods to allow the kernel to control the
power state of the device.
The problem seems to be that if the device is put in D3Hot state
before it is switched from PCI to ACPI mode then it does not properly
export its PCI configuration space and cannot be woken back up.
Adding the ACPI Methods for _PS0/_PS3 allows the kernel to transition
the device into D0 state only when it is necessary to communicate with
the device, then put it back into D3Hot state.
Change-Id: I2384ba10bf47750d1c1a35216169ddeee26881df
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5193
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This claim is useless when done before EHCI controller reset. Code in
usbdebug_init_() already sets this properly after reset, see use of
DBGP_OWNER.
Change-Id: Ic17493fe4edbbbed6ebcbef35a264fbf188f1fba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4709
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Also relocate and split header files, there is some interest
for EHCI debug support without PCI.
Change-Id: Ibe91730eb72dfe0634fb38bdd184043495e2fb08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5129
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
When 2 chips are present to get to the second one you have to use hardware
sequencing. Also use it as the fallback if chip is unknown.
Based on code in flashrom by Stefan Tauner and Carl-Daniel Hailfinger
distributed under compatible license.
Tested on Lenovo X230 which has EN25QH64 (8M) + N25Q032..3E (4M)
Change-Id: I56f3cf0406b5f09fa327ed052c8e8b1df1d8a11f
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4613
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Without it ME doesn't always start correctly and no temperature is reported,
no fan management and so on.
Change-Id: Iff71f3afbc35a1453a20d182890ae2d196c556bd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4636
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
probably a problem in MRC:
- EHCI output failure after sysagent
- no S3
- no MRC cache
- MRC needs watchdog
- less MTRR could be used by some memory map optimisations
Not tested:
- dock (probably doesn't work)
- msata (probably works)
- wwan (probably works)
- mini displayport (probably works)
Blobs:
MRC
VGA Oprom
Change-Id: I5bdb9372971f48e048848d57b6c924b79782dbde
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4679
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Ability to choose compatibility mode is interesting for testing payloads and
OS for compatibility with older systems.
As per comments
"ide_legacy_combined # TODO: Does nothing since
generations, remove from sb code?"
The "combined" mode was removed. It wasn't used by any mobo and the code for
it is almost identical to IDE one other than few bits relating to interrupt
handling and ISA mode.
Change-Id: I407a8fac753b513812a86bef5abcf39c6d81472e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Number one reason to use cbfs_get_file was to get file length.
With previous patch no more need for this.
Change-Id: I330dda914d800c991757c5967b11963276ba9e00
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4674
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
THis reduces risks of bufer overflows.
Change-Id: I77f80e76efec16ac0a0af83d76430a8126a7602d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
DRAM reset gate GPIO is different on different mobos move it to hidden config
with 60 (current value) as default.
Set it to 10 for Lenovo X201.
Change-Id: I4f3b6876d7c33d4966315091b63a76a9a0064c16
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4622
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The end of the _PS0 method that is supposed to transition the
XHCI device to D0 state is instead putting it in D3 state.
This triggers a PME_B0 GPE which causes a Notify to the XHCI
ACPI Device in the kernel and that increments the wakeup counter
and causes aborted suspends.
Instead if we just leave the device in D0 where it should be
after executing this function then the PME_B0 is not generated
and the kernel does not see a wakeup on XHCI.
Similarly I changed the _PS3 method to always put the device in
D3 at the end of the method, rather than depending on the state
to be D3 at the start.
Before this change the kernel would see the following sequence
when trying to suspend when the XHCI controller is in D3cold:
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [XHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802bc30
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [EHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802b8e8
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [HDEF] (Device) Value 0x02 (Device Wake) Node ffff88017802b1b8
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: PM: Wakeup pending, aborting suspend
kernel: last active wakeup source: 0000:00:14.0
Now it does not get a notification (due to PME_B0) when going to D0
on the way into suspend. XHCI goes from D3cold to D0 (in order to
be able to read mmio) and then back to D3hot before suspend.
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._S3D] (Node ffff88017802c000)
kernel: xhci_hcd 0000:00:14.0: PME# enabled
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff88017802bf50)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot
Change-Id: Id5cd28eede2b27d97640047feb17349ae4ab79b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65236
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4448
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The coreboot and ACPI code that clears USB3 PORTSC change status
bits was not properly preserving the state of the PED (port enabled
or disabled) status bit, and it could write 0 back to this field
which would disable the port.
Additionally add back the code that resets disconnected USB3 ports
on the way into suspend (as stated in the BWG) but take care to
clear the PME status bit so we don't immediately wake.
suspend/resume with USB3 devices
1) suspend with no devices, plug in while suspended, then resume
and verify that the devices are detected
2) suspend with USB3 devices inserted, then suspend and resume
and verify that the devices are detected
3) suspend with USB3 devices inserted, then remove the devices
while suspended, resume and ensure they can be detected again
when inserted after resume
Change-Id: Ic7e8d375dfe645cf0dc1f041c3a3d09d0ead1a51
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65733
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4473
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The recommended value in docs is D2, but lynxpoint XHCI does not even
support D2 state which causes the kernel to think this device cannot
be used as a wake source:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Device does not support D2
kernel: xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
Additionally this means the kernel will never put the device into D3
state by itself. There is SMI code that will put the device into D3
before suspend so advertising D3 here should be correct.
With this change the kernel will put the controller into D3 on suspend
and back to D0 on resume, including executing the ACPI methods
for _PS0/_PS3 that contain chipset specific workarounds.
In addition add a _PSC method to directly return the D state from the
device registers. With ALL USB devices removed the XHCI controller
goes into D3 state and the kernel can have a hard time determining
the state of the device at boot.
A kernel compiled with CONFIG_ACPI_DEBUG=y and module parameters
acpi.debug_layer=0x7f acpi.debug_level=0x2f can be used to see
what ACPI methods are executed:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff8801000a7f50)
kernel: ACPI: Preparing to enter system sleep state S3
...
kernel: ACPI: Waking up from system sleep state S3
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff8801000a7f28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
Change-Id: Ic64040eb4dd1947a1e2f0ee253a64be683e0ec70
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
meld with s3d
Change-Id: Ic6789720c4efe661dcb03a4afce8d88115854472
Reviewed-on: https://gerrit.chromium.org/gerrit/63916
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4409
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Put the device into D0 and not D3 so memory bar is available
and the subsequent commands actually do something useful
- Remove set of 818Ch[7:0]=FFh (gone in ref code)
- Fix reg 0x40/0x44 mixup
Verify that expected bits are set:
localhost ~ # pci_read32 0 0x14 0 0x10
0xe0500004
localhost ~ # mmio_read32 0xe0508144
0x000003ff
localhost ~ # mmio_read32 0xe050816c
0x000f0038
Change-Id: I388398e8c7d11e538ca18dab55d8bbd9b88f17df
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63801
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4408
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This commit adds a new Kconfig option for the LynxPoint
southbridge that will have coreboot route all of the USB
ports to the XHCI controller in the finalize step (i.e.
after the bootloader) and disable the EHCI controller(s).
Additionally when doing this the XHCI USB3 ports need
to be put into an expected state on resume in order to make
the kernel state machine happy.
Part of this could also be done in depthcharge but there
are also some resume-time steps required so it makes sense
to keep it all together in coreboot.
This can theoretically save ~100mW at runtime.
Verify that the EHCI controller is not found in Linux and
that booting from USB still works.
Change-Id: I3ddfecc0ab12a4302e6034ea8d13ccd8ea2a655d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63802
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4407
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Move this to the existing USB source files so they can share some
helper functions and keep the main smihandler code cleaner.
The XHCI sleep prepare code now implements the actual sleep
preparation steps from the ref code instead of the docs.
Change-Id: Ic90adbdaba947a6b53824e548c785b4fb3990ab5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63800
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4406
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Allow DTLE DATA / EDGE registers to be configured in board-specific
devicetree.
Change-Id: I82307d08c9cf73461db3ac7fb875a4fe70d6f9ea
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65716
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4475
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The PCIe root port has ASPM settings/workarounds that are only applied
based on the value of an undocumented bit in PCI config register 0x32C.
If that bit is not set for some reason then the settings are not applied.
This devicetree config option will force the ASPM settings for each port
based on the bit map.
Change-Id: I40b08ca9a0ef52742609bac72fb821454a373799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65314
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4453
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The default ME output is quite verbose and not all that useful
unless you are actively debugging the ME and then you can enable
the CONFIG_DEBUG_INTEL_ME option.
This commit silences the firmware capabilities and the MBP output.
Change-Id: I2b8abcb34ae0d00d9a38d029979e84ee0d0ca287
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4452
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This message allows unused clocks to be disabled based on a
devicetree setting in each mainboard.
Change-Id: Ib1988cab3748490cf24028752562c64ccbce2054
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65250
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4450
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The original ME code was assuming that the only type of messages
it would send were MKHI type and so it had some embedded checks
for that header and that type of message.
In order to support ICC messages this needs to change to handle
different header types, so now the header will be sent first
and then the data will follow, rather than the two both being
sent in the same low-level function.
This change has no real affect on the system, subsequent commit
will add new ICC messages.
Change-Id: I52848581e49b88c0a79e8bb6bda2a179419808a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65249
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4449
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The management engine is occasionally hanging the system on resume
when it is accessed. Since we actually don't need to do anything
with it on resume it can be disabled early in the resume path and
avoid assigning resources just to remove them later.
suspend/resume on falco and check /sys/firmware/log
to ensure that device 00:16.0 is disabled early and that no
resources are probed or assigned and that the device init path
does not execute.
Change-Id: I35573681e3a1d43d816d24954842cbe9c61f3484
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The management engine is slow, requiring at least 500ms between
when the Dram Init Done message is sent (right after memory training)
to when the MBP will report that it is successfully cleared and
that the ME can finally be sent the EOP message.
Currently this is adding 100-150ms to the boot time. If we defer
waiting for the MBP Clear indicator until the finalize step we
can gain back that lost time.
boot on falco with SMI debugging enabled to
ensure that the ME is locked down in the finalize step:
Finalizing Coreboot
SMI# #0
SMI_STS: PM1 APM
ME: MBP cleared
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
Change-Id: Icab4c8c8e00eea67bed5e8154d91a1eb48a492d1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4375
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There are specific programming requirements for the usb3 ports
on all LynxPoint chipsets when transitioning to D0 or D3.
LynxPoint-LP has additional workaround steps needed involving
resetting the disconnected ports when transitioning to D0.
The workarounds are implemented in ACPI code so the controller
can transition properly into D3 at runtime.
Change-Id: I3b428562f48c9cb250b97779a3b2753ed4f81509
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4374
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This reverts commit ff81f50f0e4c068b64c4a5c7f5244196ecd24965.
Deferring this step until the finalize stage will allow us
to defer waiting for the MBP clear indicator and speeding
up the boot.
Change-Id: Ib8edffd06689e72875830cd68b5aedb7ac3b0559
Reviewed-on: https://gerrit.chromium.org/gerrit/62631
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4373
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This is needed for SMBUS drivers to write to devices.
It was copied from existing intel southbridge driver.
Change-Id: Id0ce2393b2946a9c741413bca563a1a4dc0a4f5e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61893
Reviewed-on: http://review.coreboot.org/4364
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The LynxPoint-LP chipset only has one EHCI controller so we should
not attempt to write into the second one that only exists on LynxPoint-H.
Change-Id: I1eae060c7f0a5873c9684e5abfeea5cb5895ab62
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63799
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4405
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Vladimir Serbinenko