- updates from 1.6.0 ref code
- remove the step comments as they are no longer even close
- add constants for LPT revisions
build and boot on Falco
Check that RCBA+2300[1] is set:
> mmio_read32 0xfed1e300
0x00000002
Change-Id: I8b3c5fda3f3170455699a7834239cb991603e7a8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59821
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4326
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There's a need to determine if a specific gpio pin is
is set up to be a native function or not. Implement this.
Change-Id: I91d57a549e0f4fddc0b1849e5f74320fc839642c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59589
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4324
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The BIOS spec for LynxPoint calls out additional
programming steps for the PCIe Root Ports. Implement those
steps from the BIOS spec. These steps are completed before
deeper PCIe probing. The "late" programming was removed as
that was applicable to Cougar/Panther point where this
code was originally copied, though there was some overlap.
Change-Id: I64f25e4451e035d98ca6b66b0335bd280b70b074
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59558
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4323
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
PCIe Root Ports should be disabled based on pin ownership
and the strapping configuration. Implement this logic
for LynxPoint. The chip_ops->enable_dev() path is no
longer used. Instead the PCIe driver handles the enabling
and disabling of devices. This allows for having an empty
or incomplete device tree since those "allocated" devices
do not travel through the chip_ops->enable_dev() path.
The coalescing was tested to be working properly, however
not all configurations were tested.
Change-Id: I1e8bfe5e447b72ff8a4b04b650982d8c1ae0823c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59424
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4322
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
mainboard_smi_gpi has recently been updated to take a u32 argument from a
u16, but the patch introducing the fsp_bd82x6x support has been verified
on a master before this change, thus resulting in a 'cast from incompatible
type' error. Update the pointer to the correct size argument.
Change-Id: I9d62ee43f7c8ed774898f54d29a87cf463b76e91
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4479
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Add support for the bd82x6x using the Intel FSP.
The FSP is different enough to warrant its own source files
for now. The mrc/system agent chromebook solution does much more
southbridge initialization and configuration than the FSP version.
It may be combined in the future.
Change-Id: Ie493945f3d321d854728d231979a0c172d2b36de
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4017
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Ibexpeak shares few files with bd82x6x. In order for it to work correctly
their config structures from chip.h must match, so include bd82x6x/chip.h
in ibexpeak/chip.h
Change-Id: Ib56b311b8af04f4e4803d1834724680f604901cd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4277
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
LynxPoint-LP has a lot of GPEs and the "default" set has been
moved to register 4 starting at bit offset 96. This means
that PME_B0 bit in GPE0_EN/GPE0_STS is now bit 109 in LPT-LP
but still bit 13 in LPT-H.
suspend on falco and wake from usb
4 | 2013-06-19 10:49:17 | ACPI Enter | S3
5 | 2013-06-19 10:49:22 | ACPI Wake | S3
6 | 2013-06-19 10:49:22 | Wake Source | Internal PME | 0
Change-Id: I443cd4d17796888debed70c0bda27ae09accd09b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59265
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4253
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Do not directly check the return value of get_option, but instead compare
the returned value against a CB_CMOS_ error code, or against CB_SUCCESS.
Change-Id: I2fa7761d13ebb5e9b4606076991a43f18ae370ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some of the pcie logic was located in pch.c as well
as pcie.c. Move all pcie logic to the same pcie.c
file. This is a straight cut-and-paste (no logic changes)
except for a rename from pch_pcie_enable() ->
pch_pcie_enable_dev().
Change-Id: I338c53039b95f255ab9ced313c51193a9d34b404
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59277
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4251
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The function to disable devices was formerly named
pch_hide_devfn(). This routine was doing more than hiding
devices. It was disabling them, i.e. turning them off.
Therefore, rename it to pch_disable_devfn(). Also, allow
external callers to this function.
Change-Id: Id5bb319d4e67892c02a39dff49e45b2811a2f016
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59276
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4250
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The iobp functions are useful to may of the southbridge
devices as certain values need to be updated to properly
initialize the devices. Therefore expose read, write, and
updated iobp functions.
Change-Id: Id7fdd8d0d9f022f92d6285ecd8f85a52024ec2bb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59275
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4249
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
There are useful values in NVS that are set at boot
and runtime and they should not be cleared on resume.
suspend/resume twice on slippy and ensure
that the USB ports are still powered on the second suspend.
Change-Id: I4bce60b02b6637f6683120ae9c4a5c64563aacf7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56941
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Previously, I've set this config in mobo config, yet according to
Kyösti Mälkki this parameter is southbridge-specific and not
mobo-specific.
Change-Id: I92428aed5a69d88a371f5d7267bc54ba7530766c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Both EHCI and XHCI controllers have additional setup steps
that are not part of the PEI reference code so they need to
be done later.
Both controllers also have specific clock gating setup
requirements that are now implemented.
Additionally they both have specific requirements when entering
sleep states. XHCI needs something in S3/S4/S5 and EHCI only
has steps for S4/S5 entry.
Change-Id: Ic62cbc8b6255455e56b72dd5d52e27a311999330
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57033
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4217
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is an LPT-LP specific method that will enable a specific
GPIO as an ACPI SCI wake source.
It can be used by a device _DSW method to enable a pin that is
otherwise not configured to generate SCI at runtime.
It will set:
- GPIO owner to ACPI
- GPIO route to SCI
- GPIO config to GPIO, Input, Inverted
Also clean up and remove ACPI field definitions that are unused
and/or incorrect.
Change-Id: I14acc2de50e6200f61c2898a7bd1252400e0f0be
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56621
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4189
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
LynxPoint-LP has an additional 16 entries in the IOAPIC that
can be assigned to specific GPIOs when they are configured
as PIRQ.
The maximum redirection entries field in the IOAPIC needs to
be set to 0x27 when this is enabled.
Additionally specific GPIOs need to be routed to PIRQ so they
interrupt via the IOAPIC instead of the GPIO IRQ 14/15.
Change-Id: Ie587e1d203422ff6fb7fc5056d20a5ae66720991
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56620
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4203
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ssdt2 generation code was calling acpigen_patch_len().
However, none of the entries had AML object lengths that
needed patching. That resulted in the following message:
ASSERTION FAILED: file 'src/arch/x86/boot/acpigen.c', line 52
Additionally, this caused an errant write to a memory address
whose value was in the variable ltop. This was the 0 address.
Change-Id: I44abf5a4e4225220575aee6b5c9bb6b0be093a28
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56299
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ACPI code was defining two EHCI controllers and ignoring
the XHCI controller. This changes the second EHCI controller
to be XHCI instead and changes the wake resource to indicate
S3 and not S4.
cat /proc/acpi/wakeup
Device S-state Status Sysfs node
HDEF S4 *disabled pci:0000:00:1b.0
EHCI S3 *enabled pci:0000:00:1d.0
XHCI S3 *enabled pci:0000:00:14.0
Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56263
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4181
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The vendor ids were never updated to reflect LynxPoint's device
ids. Therefore, none of the initialization was being ran. Fix
this.
Change-Id: Ic6ec00c9fb1cbcb6087fd89b0acff3d83294ac6a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/55821
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4173
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to probe the gpio-lynxpoint kernel driver the
LP GPIO controller needs to be exposed as a specific
ACPI device.
This also allows the resources to be exposed to the OS via
this device instead of the catch-all LPC device.
Ensure the driver loads at boot:
gpiochip_find_base: found new base at 162
gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00
Also ensure the driver is visible in sysfs:
$ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label
INT33C7:00
Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50215
Reviewed-on: http://review.coreboot.org/4158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There were two undefined MBP types that are now defined.
These include NFC status and some interesting timing data.
ME: Wake Event to ME Reset: 6 ms
ME: ME Reset to Platform Reset: 7 ms
ME: Platform Reset to CPU Reset: 51 ms
Change-Id: I67bf1f303f3c32497041e64c40eb9ccb6a63d88a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49756
Reviewed-on: http://review.coreboot.org/4152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Slight tweaks found when looking at latest ref code when
investigating package C-state issues.
A few bits in the clock gating register don't match the
documentation and are also cleaned up.
Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4142
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Part of X201 port.
Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4052
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This reads PCH power levels via PCODE mailbox and writes the
values into the PMSYNC registers as indicated in the BWG.
Change-Id: Iddcdef9b7deb6365f874f629599d1f7376c9a190
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4143
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This will be used in a later commit to do some specific
power sequencing.
Change-Id: Id7f033bb80aed915c2498ea910cb3ac7290da37f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4137
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This adds some macros for the common GPIO defines and drops
the gpio number definition from each entry. The end result
is much easier to read. The wtm2 mainboard gpio list is modified
to use this.
Also fix a bug in the LP version of get_gpio() that was always
returning zero due to a miscompare.
Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4138
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Removing `-Wno-unused-but-set-variable` from `CFLAGS` the build for
QEMU Q35 and Roda RK9, both using the Intel 82801Ix southbridge, fail
with the following error.
src/southbridge/intel/i82801ix/lpc.c: In function 'i82801ix_enable_apic':
src/southbridge/intel/i82801ix/lpc.c:45:5: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Removing `dummy` should be safe as GCC probably optimizes it away before
anyway. That no dummy variable is used for an RCBA [1] access in Intel
Lynx Point supports that this can be dropped safely.
[1] root complex base address
[2] src/southbridge/intel/lynxpoint/early_pch.c
Change-Id: I1c138a3498228dbd025f68d5e6af0acc29ed3460
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3982
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The main usbdebug file lib/usbdebug.c was removed from romstage
build with commit f8bf5a10 but the chipset-specific parts were not,
leading to unresolved symbol errors for AMD platforms.
Add a silent Kconfig variable USBDEBUG_IN_ROMSTAGE for convenient
use of this feature.
Change-Id: I0cd3fccf2612cf08497aa5c3750c89bf43ff69be
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3983
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This is needed to apply a rule that get_top_of_ram() in romstage is
required to select HAVE_ACPI_RESUME, otherwise chipset/board has no
means to backup low memory to CBMEM on s3 resume.
Only board affected is asus/p2b.
Change-Id: Ia5cbf4e5e40af25f52a19de584d8bc5370487154
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3971
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Qemu has the fw_cfg interface at 0x510, which conflicts with
power management base address in coreboot. Move the pmbase to a
non-conflicting address. No need to worry about speedstep, it
is not supported by qemu and isn't enabled in the qemu config.
Change-Id: I3e87d8301988028ca0ea7d96c08b4e26ac15a7c2
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3938
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This retrieves back the value stored with store_initial_timestamp()
in the bootblock for southbridge.
Change-Id: I377c823706c33ed65af023d20d2e4323edd31199
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3908
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I46e69154cf576ddb642c34b6dd2bc0d27cc19b7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3811
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: Ie6776b04ca0ddb89a0843c947f358db267ac4a70
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3809
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add option to choose one of the EHCI controllers in recent
intel chipsets for usbdebug use.
Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in
rcba_config() for some mainboards, check the PCI class code
for match.
Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3440
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PCI access
functions for ramstage using the inlined functions from romstage.
Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3812
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Directory intel/common must be conditionally added in the list
of source directories, as the parent directory southbridge/intel
is unconditionally added even for boards without such device.
Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3827
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Without that fix, and with CONFIG_SMM_TSEG, we have:
src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep':
src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1
The fix is modelled after src/cpu/x86/smm/smihandler.c which
ifdefs smi_release_lock().
Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3281
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This mistake was spoted by comparison with the
src/southbridge/intel/bd82x6x/smihandler.c file.
Change-Id: I1516f0131d524bd7d001e6780e9a45402d1814d1
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3303
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an option to mark all SPI regions write protected on each S3 resume.
We were used to lock the SPI interface in the payload which isn't run on
the resume path. So we have to do it here.
For the write protection to be effective, all write opcodes in the
opmenu have to be marked correctly (as write operations) and the whole
SPI interface has to be locked. Both is already done.
Change-Id: I5c268ae8850642f5e82f18c28c71cf1ae248dbff
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3594
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All the additional work that needs to be done in EHCI BAR relocation
is independent of the hardware platform and was functionally identical
in all the copies removed.
When USBDEBUG is not selected, PCI EHCI controllers use standard
pci_dev_read_resources() call.
With USBDEBUG selected, PCI EHCI controller's device_operations
.read_resources is replaced with pci_ehci_read_resources() call,
which in turn will replace the device_operations .set_resources call.
The replacement for .set_resources reconfigures usbdebug driver side,
and calls the original .set_resources to configure hardware side.
Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3412
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The xHCI controller's MMIO space has a length of 64KiB not 4KiB.
Therefore, setting the xHCI BAR to 0xe8001000 worked the same like
setting it to 0xe8000000, as bit12 is reserved and ignored. This again
interfered with the MMIO space of the first EHCI controller and broke
S3 resume on Ivy Bridge.
AFAIK, the MRC ignores the setting of the xHCI BAR, anyway. So just drop
these lines.
Change-Id: I8af9c2ba34133f15636a9056fc8880b3b6ab95e0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3521
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Current build configuration always wants to include an Intel Management
Engine firmware (me.bin) on Sandy Bridge systems. However, we can have
a working coreboot without it, as long as the factory delivered ME
firmware is kept untouched in the flash ROM. So let the user decide if
a ME firmware will be included in the build.
Change-Id: I9a1cc29d4940ba22355eb9e653606e436f07e04c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3522
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
On newer Intel systems, the flash ROM is shared between the host
processor (BIOS), it's Management Engine (ME) and an integrated ethernet
controller (GbE). The layout of the flash ROM (and other information) is
kept in the so called Intel Firmware Descriptor (IFD). If we only want
to build coreboot to update the BIOS section, all we need is the flash
layout.
This patch adds the option to specify the flash layout in the
mainboard's Kconfig, and thus, to build without the real IFD. However,
with such a build, one has to make sure that the IFD section on the
flash ROM won't be written over (nor any other section that hasn't been
included by coreboot). A patch to write selected sections of a flash ROM
with IFD has been sent to the flashrom mailing list [1].
[1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html
Change-Id: Ia23e439a00a197fb54852263f8e206f16c3e8851
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3524
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
LynxPoint LP has only EHCI controller #1.
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: I95c59fb9d5f09afd152872e9bc0418dc67e4aeb2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3472
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: Ib6f7cfac5acf3f8170508547d1584af90273e8c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3471
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Upgrade the ICH7 bootblock to store an initial timestamp like we do it
since Sandy Brigde. I've checked the datasheets for the used scratchpad
registers and grepped for their usage. I'm pretty sure that they aren't
used on any ICH7 based board (for anything before the usual S3-resume
indication).
Change-Id: I28a9b90d3e6f6401a8114ecd240554a5dddc0eb5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3498
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
They were hard-coded to be copied from 3rdparty/ which isn't always
the right choice.
Since the defaults stay the same, this should be compatible.
Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3453
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
In case with EARLY_CONSOLE, this printk is called before any other
console is configured to transmit data. This outputs garbage on
CONSOLE_SERIAL as baudrate is not yet programmed.
For case without EARLY_CONSOLE, the order in which different console
drivers initialize is obscure. Might sometimes work properly.
Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3384
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Setting IRQ delivery to FSB got lost in the rebase process
for commit e6143531.
I captured following error on dmesg and this patch fixes it for
i82801dx.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... works.
Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3371
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to
GPIO0.
Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3436
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the
file `usb_debug.c` is added twice to the build.
This was introduced in
commit 4063ede3fb
Author: Ronald G. Minnich <rminnich@google.com>
Date: Mon Feb 4 20:31:51 2013 -0800
bd82x6x: Fix compiling with USB debug port support
Reviewed-on: http://review.coreboot.org/2784
but was unneeded because it had been already added in
the following commit.
commit 4141993536
Author: Sven Schnelle <svens@stackframe.org>
Date: Sat Jul 28 08:52:44 2012 +0200
bd82x6x: Fix CONFIG_USBDEBUG
Reviewed-on: http://review.coreboot.org/1376
Therefore basically revert that hunk.
There is no policy on how to order these additions, so leave
it to a possible separate commit, unifying this.
Kyösti Mälkki suspects that these additions were meant for
the Intel Lynx Point [1].
[1] http://review.coreboot.org/#/c/3424/
Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3425
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix obvious mistake in cycle that displays GPI status
I hope i found all duplicates of it.
Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3435
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ica3afbf8277cb025251da7af181f8de0d0036b45
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3389
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too. Define
`ACPI_EN` in the header file `pch.h`.
As commented by Aaron Durbin, a separate `pch_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I6f2559f1d134590f781bd2cb325a9560512285dc
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3182
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too. Define
`ACPI_EN` in the header file `pch.h`.
As commented by Aaron Durbin, a separate `pch_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I4478b1902d09061ca1db8eab6b71fef388c7a74c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3183
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too.
As commented by Aaron Durbin, a separate `i82801gx_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I104a2d9c2898da14d26f8f2992d5a065ad640356
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3181
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit »haswell: Add initial support for Haswell platforms« (76c3700f)
[1] used `1 << 25` to set the I/O APIC ID of 2. Instead using
`2 << 24`, which is the same value, makes it clear, that the
I/O APIC ID is 2.
Commit »Intel Panther Point PCH: Use 2 << 24 to clarify that APIC ID
is 2« (8c937c7e) [2] is used as a template.
[1] http://review.coreboot.org/2616
[2] http://review.coreboot.org/3100
Change-Id: I28f9e90856157b4fdd9a1e781472cc4f51d25ece
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3123
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit »Add support for Intel Panther Point PCH« (8e073829) [1] used
`1 << 25` to set the APIC ID of 2. Using `2 << 24`, which is the same
value, instead makes it clear, that the APIC ID is 2.
[1] http://review.coreboot.org/853
Change-Id: I5044dc470120cde2d2cdfc6e9ead17ddb47b6453
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3100
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
src/southbridge/intel/lynxpoint/pmutil.c was committed with two
things that needed fixing.
Change-Id: Ib83343a75840aa29847b607b0275971eb8140f12
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3003
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The ACPI NVS region was setup in place and there was a CBMEM
table that pointed to it. In order to be able to use NVS
earlier the CBMEM region is allocated for NVS itself during
the LPC device init and the ACPI tables point to it in CBMEM.
The current cbmem region is renamed to ACPI_GNVS_PTR to
indicate that it is really a pointer to the GNVS and does
not actually contain the GNVS.
Change-Id: I31ace432411c7f825d86ca75c63dd79cd658e891
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds configuration of SerialIO devices in the Lynxpoint-LP
chipset. This includes DMA, I2C, SPI, UART, and SDIO controllers.
There is assorted magic setup necessary for the devices and
while it is similar for each device there are subtle differences
in some register settings.
These devices must be put into "ACPI Mode" in order to take
advantage of S0ix. When in ACPI mode the allocated PCI BARs
must be passed to ACPI so it can be relayed to the OS. When
the devices are in ACPI mode BAR0+BAR1 is saved into ACPI NVS
and then updated and returned when the OS calls _CRS.
Note that is is not entirely complete yet. We need to update
the IASL compiler in our build environment to support ACPI 5.0
in order to be able to pass the FixedDMA entries to the kernel.
There are also no ACPI methods defined yet to do D0->D3->D0
transitions for actually entering/exiting S0ix states.
This is hard to test right now because our kernel does not support
any of these devices in ACPI mode. I was able to build and test
the upstream bleeding-edge branch of the linux-pm git tree. With
that tree I was able to enumerate and load the driver for the
DesignWare I2C driver and attempt to probe the I2C bus -- although
there are no devices attatched.
I am also able to see the resources from ACPI in /proc/iomem get
reserved properly in the kernel.
Change-Id: Ie311addd6a25f3b7edf3388fe68c1cd691a0a500
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This bit offset is incorrect and should only be set based
on another bit in a different register.
Change-Id: I6037534236e3a4a5d15e15011ed9b5040b435eaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2973
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The new enable_pm1() function was doing 2 things wrong:
1. It was doing a RMW of the pm1 register. This means we were
keeping around the enables from the OS during S3 resume. This
is bad in the face of the RTC alarm waking us up because it would
cause an infinite stream of SMIs.
2. The register size of PM1_EN is 16-bits. However, the previous
implementation was accessing it as a 32-bit register.
The PM1 enables should only be set to what we expect to handle in the
firmware before the OS changes to ACPI mode.
Change-Id: Ib1d3caf6c84a1670d9456ed159420c6cb64f555e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2978
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Previously southbridge_smm_init() was provided that did both
the clearing of the SMM state and enabling SMIs. This is
troublesome in how haswell machines bring up the APs. The BSP
enters SMM once to determine if parallel SMM relocation is possible.
If it is possible the BSP releases the APs to do SMM relocation.
Normally, after the APs complete the SMM relocation, the BSP would then
re-enter the relocation handler to relocate its own SMM space.
However, because SMIs were previously enabled it is possible for an SMI
event to occur before the APs are complete or have entered the
relocation handler. This is bad because the BSP will turn off parallel
SMM save state. Additionally, this is a problem because the relocation
handler is not written to handle regular SMIs which can cause an
SMI storm which effectively looks like a hung machine. Correct these
issues by turning on SMIs after all the SMM relocation has occurred.
Change-Id: Id4f07553b110b9664d51d2e670a14e6617591500
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2977
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reclaims space in ACPI NVS by removing unused fields and
adds new fields for SerialIO BARs which will be used to communicate
the allocated resources to ACPI.
Change-Id: I002bf396cf7b495bc5b7e54b741527e507aff716
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2969
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make it more similar to i82801d LPC init.
Change-Id: I7b32747ee8012c220c8628994d749999c144b716
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2545
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The haswell patches that verified correctly were not yet submitted,
but verified correctly. However they still used romcc_io.h which was
dropped in another patch earlier today.
With a lot of development happening in parallel, this is
unfortunately nothing that the gerrit 2.6 Rebase If Necessary submit
type could have fixed.
Change-Id: Ifef9ae05b22c408e78d6cff37defd68e4ed91ed9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2876
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This patch implements support for vboot firmware selection. The vboot
support is comprised of the following pieces:
1. vboot_loader.c - this file contains the entry point,
vboot_verify_firmware(), for romstage to call in order to perform
vboot selection. The loader sets up all the data for the wrapper
to use.
2. vboot_wrapper.c - this file contains the implementation calling the vboot
API. It calls VbInit() and VbSelectFirmware() with the data supplied
by the loader.
The vboot wrapper is compiled and linked as an rmodule and placed in
cbfs as 'fallback/vboot'. It's loaded into memory and relocated just
like the way ramstage would be. After being loaded the loader calls into
wrapper. When the wrapper sees that a given piece of firmware has been
selected it parses firmware component information for a predetermined
number of components.
Vboot result information is passed to downstream users by way of the
vboot_handoff structure. This structure lives in cbmem and contains
the shared data, selected firmware, VbInitParams, and parsed firwmare
components.
During ramstage there are only 2 changes:
1. Copy the shared vboot data from vboot_handoff to the chromeos acpi
table.
2. If a firmware selection was made in romstage the boot loader
component is used for the payload.
Noteable Information:
- no vboot path for S3.
- assumes that all RW firmware contains a book keeping header for the
components that comprise the signed firmware area.
- As sanity check there is a limit to the number of firmware components
contained in a signed firmware area. That's so that an errant value
doesn't cause the size calculation to erroneously read memory it
shouldn't.
- RO normal path isn't supported. It's assumed that firmware will always
load the verified RW on all boots but recovery.
- If vboot requests memory to be cleared it is assumed that the boot
loader will take care of that by looking at the out flags in
VbInitParams.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as well
by choosing the RO path.
Change-Id: I45de725c44ee5b766f866692a20881c42ee11fa8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This configures power management registers according to
the 1.2.0 reference code drop. There are many inconsistencies
with the documentation and I tried to note those with ?.
This does not do the same for LynxPoint-H yet.
Change-Id: I9b8f5c24a8b0931075a44398571c9b0d54cce6a6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2819
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This uses the new helper function added earlier.
Change-Id: Icdb5d5c51f70eeb7e39e11062276ceb3eb3d9473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2818
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is updated to handle LynxPoint-H and LynxPoint-LP
and a new wake event is added for the power button.
Boot, suspend/resume, reboot, etc on WTM2
and then check the event log to see if expected events
have been added.
Change-Id: I15cbc3901d81f4fd77cc04de37ff5fa048f9d3e8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2817
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The kernel ACPI was not happy with the Add inside a
ResourceTemplate (or perhaps within the IO declaration)
Instead make a buffer of IO reservations and turn _CRS
into a method that updates the buffer depending on the
chipset type.
This adds an \ISLP() method that checks the chipset LPC
device ID to see if it is -LP or -H.
It also increases the PM base reservation to 256 bytes
and moves both GPIO and PM base to above 0x1000 on -LP
chipsets.
Change-Id: I747b658588a4d8ed15a0134009a7c0d74b3916ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2815
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was put in for debugging and experimentation on i945
and has been copied around since. Drop it from lynxpoint.
Change-Id: I0b53f4e1362cd3ce703625ef2b4988139c48b989
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2814
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are subtle yet significant differences in some of the
registers in the power management region between LynxPoint-H
and LynxPoint-LP.
In order to reduce code that is accessing these registers and
would need special cases this adds a number of helper functions
that can be used in both ramstage and SMM.
This commit just adds the new functions, subsequent commits will
start to use them.
Change-Id: I411da75da519f5b3198a408078cbf3114e426992
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2813
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These base addresses are used in several places and it
is helpful to have one location that is reading it.
Change-Id: Ibf589247f37771f06c18e3e58f92aaf3f0d11271
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2812
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a helper function pch_is_lp() that will return 1 if
the current chipset is of the new "low power" variant used
with Haswell ULT.
Additionally these functions are added to SMM so it can
be used there.
Change-Id: I9acdea2c56076cd8d9627aba66cf0844c56a38fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2811
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to be able to talk to an EC via standard path.
Change-Id: I3fe76882dec9a0596cbc1c844afa2ddb03ed771c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2810
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I'm not sure if I screwed this up originally or the Intel docs changed
(I didn't bother to go back and check). According to ME BWG 1.1.0 the give
up bit is in the host general status #2 register.
Change-Id: Ieaaf524b93e9eb9806173121dda63d0133278c2d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2808
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
So it can get used in both romstage and ramstage.
Change-Id: Ief9eaafdd91df2a7b668de1a9b83aea3af3ff894
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2802
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
SPI accesses can be slow depending on the setup and the access pattern.
The current SPI hardware setup to cache and prefetch. The alternative
cbfs_load_payload() function takes advantage of the caching in the CPU
because the ROM is cached as write protected as well as the SPI's
hardware's caching/prefetching implementation. The CPU will fetch
consecutive aligned cachelines which will hit the ROM as
cacheline-aligned addresses. Once the payload is mirrored into RAM the
segment loading can take place by reading RAM instead of ROM.
With the alternative cbfs_load_payload() the boot time on a baskingridge
board saves ~100ms. This savings is observed using cbmem.py after
performing warm reboots and looking at TS_SELFBOOT_JUMP (99) entries.
This is booting with a depthcharge payload whose payload file fits
within the SMM_DEFAULT_SIZE (0x10000 bytes).
Datapoints with TS_LOAD_PAYLOAD (90) & TS_SELFBOOT_JUMP (99) cbmem entries:
Baseline Alt
-------- --------
90:3,859,310 (473) 90:3,863,647 (454)
99:3,989,578 (130,268) 99:3,888,709 (25,062)
90:3,899,450 (477) 90:3,860,926 (463)
99:4,029,459 (130,008) 99:3,890,583 (29,657)
90:3,834,600 (466) 90:3,890,564 (465)
99:3,964,535 (129,934) 99:3,920,213 (29,649)
Booted baskingridge many times and observed 100ms reduction in
TS_SELFBOOT_JUMP times (time to load payload).
Change-Id: I27b2dec59ecd469a4906b4179b39928e9201db81
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2783
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At some point, compiles with USB Debug port stopped working. This change makes
a trivial reordering in the code and adds two makefile entries to make it build
without errors. It also works on stout.
Build and boot as normal. Works. Enable CONFIG_USB, connect USB debug hardware
to the correct port (on stout, that's the one on the left nearest the back) and
watch for output.
Change-Id: I7fbb7983a19b0872e2d9e4248db8949e72beaaa0
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2784
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Some initialization steps were done twice
- One step was missing for Panther Point HDA
- Added a 1ms delay after reset
- Increased timeout to 1ms for all codec operations
Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Certain SATA devices claim to support SATA 6 Gbps, but in fact have
bugs. For these devices, add a config option to force the SATA link
speed to something other than default.
Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables power management and clock gating on XHCI.
Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
objcopy -B provides symbols of the form _binary_<name>_(start|end|size).
However, the _size variant is an absoult symbol. If one wants to
relocate the smi loading the _size symbol will be relocated which is
wrong since it is suppose to be a fixed size. There is no way to
distinguish symbols that shouldn't be relocated vs ones that can.
Instead use the _start and _end variants to determine the size.
Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The bd82x6x requires some additional setting on S3/S4 entry.
Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the PCH function to SMM for follow-on SMM patches that
require these functions.
Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These enables are hidden behind IOBP for some reason.
Boot to linux with SDIO disabled and see that
the SDIO driver does not load and crash the system.
Change-Id: Icfbfa117e9e57a51d32db7f6366a9d0d790adcf0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2695
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit updates the Lynx Point resource reservations before
the coreboot allocator assigns resources. There is no need to mark
anything as subtractive decode because there are no devices/buses
linked to the LPC device.
The I/O range reservations consists of claiming the first 4KiB
of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode
ranges are checked against the default claimed range. If those
ranges overlap or fall outside of the default range then those
resources are added.
The MMIO range reservations consist of claiming everything from
the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range
register are then conditionally added if they fall outside of
the default MMIO range.
Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2682
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Add device IDs for lynxpoint mobile and LP variants.
- Update the clock gating setup based on BWG
- Update the SATA programming based on BWG
- Add a DEVSLP0 mux config register
Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2649
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
There are enough subtle differences that it is useful to have
a Kconfig entry to differentiate the ULT/LP chipet from the
desktop/mobile versions.
Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2645
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This commit contains a bevy of updates:
- PCI device id is updated to match Lynx Point EDS in the ME driver.
- Allocate the memory to store the consumption of the MBP.
- me_bios_payload structure is now a structure of pointers that point
into the allocated memory.
- The ICC profile structure was updated to correctly reflect the
documentation.
Verfied that output of MBP reading can handle unknown items.
Change-Id: I43cc45e6b797444c105e7c842eb5684e9c104687
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2641
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
According to the 0.8.0 ME BWG this is a new state. It's not very clear
what exactly it entails, but the Basking Ridge CRB was tripping it when
MRC_DEBUG was enabled (presumably because of a DID timeout).
Instead of 0x17 one can now see the proper message for this state.
Change-Id: I5bda1de7d3d957d38a4760a02dcd170ec48782e9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2640
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is no longer tied to a GPIO but has a proper chipset pin.
Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2643
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2618
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The register that controls global reset is named the Power
Mangement Initialization Regiser (PMIR). Update the defines
to reflect the documentation.
Additionally, there is no core well reset control according to the
EDS. There is, however, a CF9 lock field to lock this register down.
Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2619
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME9 requirements have added some registers and changed some
of the MBP state machine. Implement the changes found so far in
the ME9 BWG. There were a couple of reigster renames, but the
majority of th churn in the me.h header file is just introducing
the data structures in the same order as the ME9 BWG.
Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18
Signed-Off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2620
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This follows the new method outlined in the LPT BWG.
It is also very pedantic about its operation so it
is easier to read and compare against the docs and
the reference code implementation.
Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2694
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add PEI updates and ACPI updates for supporting EHCI to XHCI
USB port support.
Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2519
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
According to both Haswell and the SandyBridge/Ivybridge
BWGs the save state area actually starts at 0x7c00 offset
from 0x8000. Update the em64t101_smm_state_save_area_t
structure and introduce a define for the offset.
Note: I have no idea what eptp is. It's just listed in the
haswell BWG. The offsets should not be changed.
Change-Id: I38d1d1469e30628a83f10b188ab2fe53d5a50e5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This broke because those components were not yet
committed when the patch to drop the driver class
was made.
Change-Id: I29948223503a6c4b196eafa169c064cd26da1be1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for ICH9 southbridge
Change-Id: I70612431101bf48d9dcc96ee1b37d257c9ad2ee2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1690
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
hard_reset was indeed consolidated and moved into the southbridge
code a while ago, but the config variable was still kept alife, with
some duplicate code.
Change-Id: I60d4a87de916667f6e89353dfbe1a7b9eca380f7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The search for save state was comparing the entire RAX
value when it needs to just operate on the bottom byte
so it can find the GSMI command in bits 7:0 but not the
extended command code in bits 15:8.
Change-Id: I526c60e6b3732fa3680a17a4bed2a2ef23ccf94f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1774
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of hijacking some random memory addresses to
relay the GNVS pointer to SMM we can use EBX register
during the write to APM_CNT register when the SMI is
triggered.
Change-Id: I79a89512c40353d72ad058cbf2e6a23a696945da
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1766
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is currently used by the ELOG GSMI interface but is a
good way to pass data to SMM so move the current searching code
to a separate function and make it a bit more versatile with the
checks it does to find a match so it can be used in other
situations.
Change-Id: I5b6f92169f77c7707448ec38684cdd53c02fe0a5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For reasons of security and testing we want to be able to
enable/disable ME section locking through a config option.
Change-Id: I341c577cdae86be62c0e3d32bbd6b3333c004a5f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1798
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Right now coreboot's build process produces images that are
not booting on actual hardware because they are smaller than
the actual flash device and also don't have an IFD nor an ME
firmware in them. In order to produce bootable images, you
needed a wrapper script / extra step until now. With this
change, the resulting coreboot.rom is actually bootable.
Change-Id: I82714069fb004d4badc41698747a704bd9fed4da
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1771
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a basic romstage driver that can be used for the
MRC cache code on systems where we do not have the MRC cache
stored in a flash region that is memory mapped.
It uses the hardware sequencing interface to avoid having
to know anything about the flash chip itself.
BUG=chrome-os-partner:15031
BRANCH=stout
TEST=manual: this was tested with debug code added to romstage
that attempted to read the MRC cache at offset 0x3e0000.
SPI READ offset=003e0000 size=64 buffer=ff7fba00
SPI ADDR 0x003e0000
SPI HSFC 0x3f00
SPI READ: 0=4443524d
SPI READ: 1=00000bb0
SPI READ: 2=00008e24
SPI READ: 3=00000000
SPI READ: 4=001c8bbb
SPI READ: 5=0c206466
SPI READ: 6=0a043220
SPI READ: 7=000058b4
SPI READ: 8=00000000
SPI READ: 9=00000000
SPI READ: 10=00100000
SPI READ: 11=00100005
SPI READ: 12=20202025
SPI READ: 13=000e0001
SPI READ: 14=00000000
SPI READ: 15=00000000
Change-Id: I5f78f53111f912ff5dda52bbf90fdc1824b82681
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1777
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Fix handling of 5-byte Fast Read command in the ICH SPI
driver. This fix is ported from the U-boot driver.
- Allow CONFIG_SPI_FLASH_NO_FAST_READ to be overridden by
defining a name for the bool in Kconfig and removing the
forced select in southbridge config
- Fix use of CONFIG_SPI_FLASH_NO_FAST_READ in SPI drivers
to use #if instead of #ifdef
- Relocate flash functions in SMM so they are usable.
This really only needs to happen for read function pointer
since it uses a global function rather than a static one from
the chip, but it is good to ensure the rest are set up
correctly as well.
Change-Id: Ic1bb0764cb111f96dd8a389d83b39fe8f5e72fbd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1775
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Intel PCH can override the ASPM settings via the MPC2 register.
Add a chip override for F0-F7. Mainboards may implement this as
needed.
This also fixes the final PM setup being done too early. It was
being done prior to the PCIe ASPM setup, which happens in the
bridge scan.
Change-Id: Idf2d2374899873fc6b1a2b00abdb683ea9f5bd6b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1796
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Right now the SPI bus is getting set to 20mhz for transactions
initiated with the software sequence interface.
In order to be able to do reasonable fastread/write/erase we
can bump this up to a higher value at boot before it gets
locked at 20mhz.
To do this read out the speed set in the SPI descriptor for
hardware sequencing and apply it to software sequencing.
Change-Id: I79aa2fe7f30f734785d61955ed81329fc654f4a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The chips we are using do not use BE52 (block erase 0x52)
so we can use that opcode menu location to enable fast read.
Change-Id: I18f3e0e5e462b052358654faa0c82103b23a9f61
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And move the pre-hardwaremain post code to 0x79
so it comes before hardwaremain at 0x80.
Emit these codes from ACPI OS resume vector as well
as the finalize step in bd82x6x southbridge.
Change-Id: I7f258998a2f6549016e99b67bc21f7c59d2bcf9e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The sleep type is 5 for S3 and 7 for S5.
Change-Id: I7ffdb3d27b6994ac4a12a343caf4d7abb82fe6ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These bits are used by the IGD OpRegion code
Change-Id: I89a11fc5021d51e0c1675ba56f6a3bc3b79bb8aa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1751
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In order to support Intel's IGD Opregion standard, we need
an additional set of flags shared between firmware, ACPI, SMM, and the
graphics driver.
Change-Id: I1a9b8dff5e5ee8d501b6672bc3bcca39ea65572e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the driver is initialized before the lockdown then it will
fail to work after the lockdown bit is set.
Change-Id: Idc05d33d8d726bf29cb3c9b1b4604522bd64170a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In case tseg_relocate() is called again on a pointer we should not
relocate it again.
Change-Id: Ida1f9c20dc94b448c773b14d8864afe585369119
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We are seeing ME disabled and ME error events on some devices
and this extended info can help with debug.
Also fix a potential issue where if the log does manage to get
completely full it will never try to shrink it because the only
call to shrink the log happens after a successful event write.
Add a check at elog init time to shrink the log size.
Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The handling of write enable was not entirely correct,
the opcode needs to be skipped when the controller is
locked down.
Addresses were not getting set properly for erase commands
which seemed to mostly work when the previous command had
set an address.
Tested by adding events to the event log at runtime on a
freslhy flashed device (with locked down SPI controller)
until the log log shrink happens to ensure it does not hang:
hexdump -C elog.event.kernel_clean
00000000 01 00 00 00 ad de 00 00 00 00
for x in $(seq 1 232); do
cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog
done
mosys eventlog list | tail -6
154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
158 | 2012-09-01 13:54:43 | Log area cleared | 1030
159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that WREN prefix is handled properly ELOG is able to write
when the SPI controller is locked down.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: If6d0dced7cb0f5ca7038b3d758f31b856826d30b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1712
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
The code that attempts to use the opmenu needs to have a special
case for write enable now that it is handled as an atomic prefix
and not as a standalone opcode.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1710
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
This appears to fix an infrequent resume hang on Ivybridge.
Tested on 2 devices with 15k suspend/resume cycles each
Change-Id: I53618bc7966824413f1720a2be3cbd2550e29473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1704
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The names were set at various times during development, but
the way the code works, you might end up with the wrong name
being displayed in the logs. Instead of doing magic, just
display both names for each component
Change-Id: I1f8ce44d156442f5f7d717e1a2b47ed1218d4527
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1413
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Move beep commands to board-specific area as they need to be different for
different codecs.
Change-Id: I2a1ac938c49827cc816a95df10793a7e234942bf
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: http://review.coreboot.org/1410
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In accordance to PCH EDS 14.1.35.1
Change-Id: I2e6cec6d4f49f404e33a171a8fbd6e4880327896
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1411
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Compilation fails with set_debug_port undeclared in ramstage and
smm code. Fix that by adding usb_debug.c to the appropriate stages.
Change-Id: I2a037d3c5fab76ae6ea65c3a7f4d4e7561bb6d34
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1376
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Modelled after http://review.coreboot.org/#/c/443 to get bd82x6x in
sync.
Change-Id: I36d715310157b9f9074f2a1c80710f85833020b4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1324
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This will log if the ME is disabled or has an error.
1) disable ME via EC console: gpioset PCH_HDA_SDO 1
2) boot the device
3) read eventlog with "mosys eventlog list"
71 | 2012-07-13 10:10:55 | Management Engine | Disabled
Change-Id: I9f6ee452d2aea76e6a5ea2cd50a50ff36245692a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will allow various teams to select which thermal sensor
will control the thermal zones.
Also add a method to notify the thermalzones of a change
so these threshold/sensor methods take effect.
Needs a modified BIOS that uses the NVS TMPS value in
the thermalzone to read a different sensor.
Then, use a kernel driver that contains the following:
/* Adjust temperature sensor id to 2 */
union acpi_object param;
struct acpi_object_list input;
param.type = ACPI_TYPE_INTEGER
param.integer.value = 2
input.count = 1;
input.pointer = ¶m;
acpi_evaluate_object(NULL, "\\TMPU", &input, NULL);
And ensure that the temperature sensor that is being
monitored switches to ID 2.
Change-Id: I6319741358ba31eb8a3dc635d64f3f0acf683386
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME device was being sent EOP and the PCI device hidden during
coreboot so it was not available in the SMI finalize step.
This also flips the PCI vendor/device dword around for the match.
Boot on Panther Point with serial and SMI debugging enabled and see
that ME EOP message is sent and the device is hidden at end of
U-boot and before the kernel loads.
Finalizing Coreboot
SMI# #0
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PM1_STS: TMROF
PM1_EN: 120
Starting kernel ...
Change-Id: I230038c62c50db2a1c94078c0a2a67bdc232440e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1338
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The LPC bus normally allocates the range for legacy devices,
0-0x1000. Some devices on LPC are above that range and need to
be accounted for. Check the decode range settings for addresses
> 0x1000 and reserve them.
Change-Id: Idba800d7cee3185296f29dd237ba306f3de8de55
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1337
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Events are logged for SMIs that trigger ACPI sleeps state
entry and when the power button press triggers an SMI such
as at the developer/recovery screens.
Generate ACPI sleep state events and power button
events and verify they show up in the log:
153 | 2012-06-23 17:12:59 | ACPI Enter | S5
184 | 2012-06-23 17:15:50 | ACPI Enter | S3
216 | 2012-06-23 17:28:58 | Power Button
Change-Id: Iba134d619780e459bce189d36d57844997ffb009
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1320
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Unfortunately the drive strength values are very much board
specific and different between mobile and desktop so we don't
try to do any fancy detection here but let it be specified
directly in the devicetree.
Change-Id: I66674bff0de04ecd088fb09afad1cf801a374df2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to support the GSMI interface the SMI handler needs
to find and use the state save area from the same CPU that
initiated the SMI. In this case it is a synchronous SMI
resulting form an IO write to port 0xB2.
To find the right CPU state save area iterate over the region
until the "IO Misc Info" field reports the expected value and
then proceed to use that state save area.
This is needed because the coreboot SMI handler only executes on
one core, and that core is non-deterministic. It is likely that
the core executing the C SMM handler is not the same one that
actually did the IO write to 0xB2 and generated the SMI.
The GSMI parameter buffer is passed as a pointer to EBX in the
tate save area, and the GSMI command is extracted from EAX before
it is used as the return value.
This interface is tested by enabling CONFIG_GOOGLE_GSMI in the
kernel and generating events and verifying that they end up
in the event log.
159 | 2012-06-23 16:22:45 | Kernl Event | Clean Shutdown
184 | 2012-06-23 17:14:05 | Kernl Event | Oops
185 | 2012-06-23 17:14:05 | Kernl Event | Panic
Change-Id: Ic121ea69e9f50c88467c435e095c3e3629989806
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a temporary workaround so the SPI bus can be accessed
at runtime in SMM code until the SPI opcode menu is used
properly.
Change-Id: I93d188c55b66d8dce49fa91a1de53ee195944b30
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is called from the SMI handler install because those
setup functions clear many of these registers.
Ensure that these events show up in the log as appropriate.
Example log output:
159 | 2012-06-23 14:31:54 | SUS Power Fail
160 | 2012-06-23 14:31:54 | System Reset
161 | 2012-06-23 14:31:54 | ACPI Wake | S5
Change-Id: I48c423c10ee7e6c2829bcc95f6cfabb4979c25a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is exported so it can be used in other
places that need similar relocation due to TSEG.
Change-Id: I68b78ca32d58d1a414965404e38d71977c3da347
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1310
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was introduced when porting the SPI driver over from u-boot but it
is not needed. Hence drop the extra typedef and use device_t instead.
Change-Id: I3ab797a8e482d1c9aa1d004e488e99aeaffcdd8b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1331
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
CPUs with configurable TDP will run the TSC at the max non-turbo
ratio for the maximum TDP value, which can cause issues if another
TDP is desired. To deal with this we set the flex ratio to the
nominal TDP ratio early in the boot and then configure the Soft
Reset Data registers so the PCH can tell the CPU what frequency
to run at after a reset.
This is done very early in the bootblock because it is necessary
to reset the system after setting a flex ratio.
The end result is that the TSC will now increment at the max
non-turbo frequency for the nominal TDP.
On some system with 1.8GHz CPU ensure that the kernel
detects the CPU speed as ~1800mhz rather than ~2300mhz:
> dmesg | grep "MHz processor"
[ 0.004000] Detected 1795.801 MHz processor.
Change-Id: I8436dced9199003b6423186a2b041e3f7b84ab8c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are enough differences that it is worth defining the
proper map for the sandybridge/ivybridge CPUs. The state
save map was not being addressed properly for TSEG and
needs to use the right offset instead of pointing in ASEG.
To do this properly add a required southbridge export to
return the TSEG base and use that where appropriate.
Change-Id: Idad153ed6c07d2633cb3d53eddd433a3df490834
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1309
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- add Kconfig option for CONFIG_SPI_FLASH_SMM
- compile subsystem and chip drivers for smm if enabled
- change mdelay(1) to udelay(500) since mdelay is not defined
in SMM and a 1ms delay is worth avoiding
- make flash chip structure non-const so the probe function
pointers can be relocated for use in TSEG
- Make SMM PCI access possible in southbridge SPI code
Change-Id: Icfcbbe8e4e56658769d46af0b5bf6c79a6432641
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1313
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME needs to be talked to through the PCIe memory mapped config
space.
Change-Id: Ic2c5a572a126722a08a82d95df13d11507586c6b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1284
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In the short term there might be devices with Sandy Bridge CPUs
on mainboards with Panther Point PCHes. While this configuration
option is perfectly valid, coreboot currently ties Sandy Bridge to
Cougar Point and Ivy Bridge to Panther Point. One occurence is in
the ME handling code.
To make coreboot most flexible, compile both ME handlers into
coreboot and decide at runtime which one to use.
Change-Id: Icffe2930873f67c99c3f73e37e7a967f4f002b88
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1280
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- On Cougar Point there may have been stack corruption during the
ME hash verification
- On Panther Point the ME firmware hash was not passed on to the
OS
Change-Id: I73fc10db63ecff939833fb856a6da1e394155043
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The PCIe device enable function prints when it disables a device.
The PCIe ports(bridges) use a different routine that didn't print
the message. Add it to be consistent and to provide better debug
output.
Change-Id: I8462c48e7f4930db68703f0bfb710c01c9643a98
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1326
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Duncan Laurie