Sets all unused sata ports to disable in the device tree
Note:
SATA4 and SATA5 are located at the bottom of the board, but there
is no connector for this. Apparently, a board with an increased
number of ports is very rare. Perhaps this is a separate variant
of the Asrock motherboard. For this reason, these ports are also
disabled
Change-Id: I5b3ad372f1d6607cc7b4a78e3c59d2a5ae1d2cf5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable spi0, i2c0 and i2c1 in the “SerialIoDevMode” register for the
following reasons:
1. when the AMI BIOS is used, these pci devices are disabled in
lspci.log;
2. there are no pads in the inteltool.log that use the functions of
these buses
Change-Id: I01ab10eb3fd41e81a1726805247c2b472d72287c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35070
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The string "register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" was mistakenly
taken from the Intel KBL-RVP8 devicetree.cb. Remove it, since the i2c4
bus is disabled in the "SerialIoDevMode" register
Change-Id: I44ecd5c22efd66b02a2851dc14a1a95421f39a71
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1) VR domains current limit Icc max for Sky/Kaby Lake S is set based
on the processor TDP [1]. Updates information about this
2) Sets VR voltage limit to 1.52V, as described in the datasheets [2,3]
[1] Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
[2] page 112-119, 6th Generation Intel(R) Processor Families
for S-Platforms, Volume 1 of 2, Datasheet, August 2018.
Document Number: 332687-008EN
[3] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I6e1aefde135ffce75a5d837348595aa20aff0513
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 [1]
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The pad configuration in this patch was
generated using the pch-pads-parser utility [2]. The inteltool dump
before and after the patch is identical (see notes)
Notes:
1. For some reason, GPIO RX State (RO) for the GPP_F4 and GPP_G10
changed the value to 0, but this doesn't affect the motherboard
operation. Perhaps this is because PAD_CFG1_GPIO_DRIVER is set to
PAD_CFG_GPI_INT(), and the pad is not actually connected. So far I
haven't circuit diagram to check this out.
2. According to the documentation [1], the value 3h for RXEVCFG is
implemented as setting 0h.
3. If the available macros from gpio_defs.h [3] can't determine the
configuration of the pad, the utility [2] generates common
_PAD_CFG_STRUCT() macros
[1] page 1429,Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 2 of 2,
February 2019, Document Number: 332691-003EN
[2] https://github.com/maxpoliak/pch-pads-parser/tree/stable_1.0
[3] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
Change-Id: I01ad4bd29235fbe2b23abce5fbaaa7e63c87f529
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This provides stack guards with checking and common
entry into postcar.
The code in cpu/intel/car/romstage.c is candidate
for becoming architectural so function prototype
is moved to <arch/romstage.h>.
Change-Id: I4c5a9789e7cf3f7f49a4a33e21dac894320a9639
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34893
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DqByteMapCh0 and DqByteMapCh1 are declared adjacently in the
FSP_M_CONFIG struct, so it is tempting to begin memcpy at the address of
the first array and overwrite both of them at once. However, FSP_M_CONFIG
is not declared with the packed attribute, so this is not guaranteed to
work and is undefined behaviour to boot. It is cleaner and less tricky
to copy them independently. The same is true for DqsMapCpu2DramCh0 and
DqsMapCpu2DramCh1, so we change those as well.
Change-Id: Ic6bb2bd5773af24329575926dbc70e0211f29051
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 136538{8,9}, 140134{1,4}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33135
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When entry to romstage is via cpu/intel/car/romstage.c
BIST has not been passed down the path for sometime.
Change-Id: I345975c53014902269cee21fc393331d33a84dce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The processor P_BLK doesn't support throttling. This behaviour could be
emulated with SMM, but instead just update the FADT to indicate no support
for legacy I/O based throttling using P_CNT.
We have _PTC defined in SSDT, which should be used in favour of P_CNT by
ACPI aware OS, so this change has no effect on modern OS.
Drop all occurences of p_cnt_throttling_supported and update autoport
to not generate it any more.
Change-Id: Iaf82518d5114d6de7cef01dca2d3087eea8ff927
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Remove implementation of 24 MHz clock, available only
on Haswell ULT SKUs. Use TSC_MONOTONIC_TIMER instead
for all boards.
Change-Id: Ic4aeb084d1b0913368f5eaa46e1bd68411435517
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
By default, the LPC SIRQ mode is set to Quiet mode. Therefore, COM-port
from the SurerIO chip don't work correctly after the LPC controller (PCI
0:1f.0) initialization. Console output is broken. The patch fixes this
bug by overriding the serirq_mode option in the devicetree.cb to set
Continuous SIRQ mode
Change-Id: I37e26b271fb61f6c0343d6bf65c029924df82caf
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33801
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The asrock/h110m has a NCT6791D, but is selecting the NCT6776-specific
SUPERIO_NUVOTON_NCT6776_COM_A symbol. Use the NCT6791D symbol instead.
Change-Id: I9f3fde161844f919b070f2b6ce7e106411439a9a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <m.poliakov@yahoo.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This does the following:
- select MAINBOARD_USES_FSP2_0 on Kabylake (does not support FSP1.1)
- Remove stale Kconfig option on intel/saddlebrook
- select SOC_INTEL_KABYLAKE on intel/kblrvp
Change-Id: I64f48eeb00150aea039d533b0ac471fdd8483b90
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This automatically detects whether the southbridge supports AHCI.
If AHCI support is selected it will be used unless "sata_no_ahci" is
set in the devicetree to override the behavior.
Change-Id: I8d9f4e63ae8b2862c422938f3103c44e761bcda4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Some variants only support 4 PCIe ports so there is no need to have
those unavailable ports in the devicetree.
Change-Id: I154cae358fb7f862fc0c8eaa620474b37b5e6484
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30821
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Apply commit d7b88dcb (mb/google/x86-boards: Get rid of power button
device in coreboot) to AMD Brazos boards [1]:
> As per the ACPI specification, there are two types of power button
> devices:
> 1. Fixed hardware power button
> 2. Generic hardware power button
>
> Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
> is not set in FADT by the BIOS. This device has its programming model
> in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
> power button device by default if the power button FADT flag is not
> set.
>
> On the other hand, generic hardware power button can be used by
> platforms if fixed register space cannot be used for the power button
> device. In order to support this, power button device object with HID
> PNP0C0C is expected to be added to ACPI tables. Additionally,
> POWER_BUTTON flag should be set to indicate the presence of control
> method for power button.
[..]
> This change gets rid of the generic hardware power button from all
> google mainboards and relies completely on the fixed hardware power
> button.
The same problem exists with the AMD Hudson devices in coreboot.
For AMD Hudson (2) and Yangtze based devices this was removed in commit
44f2fab8 (AMD hudson and yangtze boards: Let mainboard declare power
button) [2].
Two devices are detected.
$ dmesg | grep Button
[ 0.209213] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.209254] ACPI: Power Button [PWRB]
[ 0.209332] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.209349] ACPI: Power Button [PWRF]
$ sudo evtest
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Power Button
/dev/input/event1: Power Button
[..]
[1]: https://review.coreboot.org/5546
[2]: https://review.coreboot.org/27272
Change-Id: I0cbecb72f7e1bf3d051d3b7656c6af4d6f43b497
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/27496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We keep the support, though. Just now that `libgfxinit` is fixed, we
don't need the distinction anymore. Causally, we also don't need
CPU_INTEL_MODEL_306AX any more.
TEST=Played tint on kontron/ktqm77. Score 606
Change-Id: Id1e33c77f44a66baacba375cbb2aeb71effb7b76
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use common code to detect ACPI S3.
Tested on Thinkpad X60.
Change-Id: Ia759a9ed141efc8130860300f2a8961f0c084d70
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds support PCIe Gen 3 with 8GT/s link speed for PEG x16
slot. All parameters for FSP are set during initialization in
romstage. Now there is no need to additionally configure the FSP
before building the ROM image.
Tested on Intel Core i5-6600 processor with the following devices:
- LP11000e Fibre Channel HBA (Gen2 x8);
- PEX8734 PCIe Fabric/Switch (Gen3 x16);
- NVIDIA GeForce GTX 1060 GPU (Gen3 x16).
GPU works with an nouveau and proprietary driver under Ubuntu 18.04.2
(4.15.0-46-generic GNU/Linux kernel). Discrete graphic card is used
as primary device for display output. Dynamic switching is not yet
supported.
Tianocore (edk2-stable201811-216-g51be9d0) is used as the payload.
Change-Id: Ia4f29df47d76de5069fe53120434cc7c2ab6f044
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31948
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If an external graphics card is inserted in the PEG, it will be used
as the primary display device (as in the AMI BIOS)
Change-Id: Iea846179fc309c2b98093de37c05ceb332081f4f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The InternalGfx option in devicetree.cb is not used to enable iGPU.
The patch removes this option from chip.h and mb/*/devicetree.cb
files for all boards with skl/kbl processor.
Change-Id: I41ecca3fdfb1d4b20ee634a13263ff481dcf440e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Drop 'include <string.h>' when it is not used and
add it when it is missing.
Also extra lines removed, or added just before local includes.
Change-Id: Iccac4dbaa2dd4144fc347af36ecfc9747da3de20
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This board is compatible with Intel Skylake and Kaby Lake generation
processors. This patch contains the minimum configuration for booting
and stable operation of the Ubuntu OS (18.04.1, Linux kernel 4.15).
It is based on Intel RVP8 mainboard.
Intel Kaby Lake FSP 3.6.0 is used to initialize CPU and PCH.
Graphics init with libgfxinit.
Works:
- Integrated graphics (only DVI port, tested with 1920x1080);
- PEG x16 (FSP must be configured with BCT to enable PEG);
- all PCIe x1 slots;
- all USB and SATA ports;
- SuperIO COM port for console;
- onboard audio.
TODO:
- other SuperIO functions;
- onboard network chip;
- suspend and resume;
- documentation.
Tested on Intel Core i5-6600 processor with Seabios (rel-1.12.0-10-
g171fc89) and Tianocore/edk2 (vUDK2018-8-ge6eccfc) as a payload.
Change-Id: I69396edc50948cf1d0da649241ce92171d32daf7
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
MMIO operations are arch-agnostic so the include
path should not be arch/.
Change-Id: I0fd70f5aeca02e98e96b980c3aca0819f5c44b98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31691
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Also includes lines sorted
Change-Id: Idf2b41f471f531b2a9c3e620563e3c658dea4729
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31267
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the memory controller the separate sockets becomes a useless
distinction. They all used the same code anyway.
UNTESTED: This also updates autoport.
Change-Id: I044d434a5b8fca75db9eb193c7ffc60f3c78212b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31031
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use parallel MP init code to initialize all AP's.
Also remove guards around CPU code where all platforms now use
parallel MP init.
This also removes the code required on lapic init path for
model_6fx, model_1017x and model_f4x as all platforms now use the
parallel MP code.
Tested on Intel DG41WV, shaves off about 90ms on a quad core.
Change-Id: Id5a2729f5bf6b525abad577e63d7953ae6640921
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25601
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Id3a161c54341d0c5c569ea6118ee6f890b7f62e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30735
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Ib212f24c3d697a009d2ca8e2c77220de4bfb7573
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30733
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IMC is used on some of the AMD reference designs, so do not
touch them yet.
Change-Id: Iae21e0294f0155f07fb4f4348ebc5b3120d50fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/18536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
