The original version of the mem_chip_info structure does not record rank
information and does not allow precise modeling of certain DDR
configurations, so it falls short on its purpose to compile all
available memory information. This patch updates the format to a new
layout that remedies these issues. Since the structure was introduced so
recently that no firmware using it has been finalized and shipped yet,
we should be able to get away with this without accounting for backwards
compatibility.
BRANCH=corsola
Cq-Depend: chromium:3980175
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If34e6857439b6f6ab225344e5b4dd0ff11d8d42a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68871
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Xixi Chen <xixi.chen@mediatek.corp-partner.google.com>
The size of a pointer changes between a 32 and 64 bit coreboot build. In
order to be able to use a 32 bit FSP in a 64 bit coreboot build, change
the pointer in the UPDs to a uint32_t to always have a 32 bit field in
the UPD for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I81f3a38344f91cecb4fe5431ed211834e5ed599c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69897
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The size of a pointer changes between a 32 and 64 bit coreboot build. In
order to be able to use a 32 bit FSP in a 64 bit coreboot build, change
the pointer in the UPDs to a uint32_t to always have a 32 bit field in
the UPD for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I419fef73d2881e323487bc7fe641b2ac4041cb17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
DTTS indicated Dynamic Thermal Table Switching.The proposal would like
to develop the schematic for switching 6 thermal table by lid status,
machine body mode and temperature. After entering the OS, the thermal
table would be table A. If the “Motion” or “Lid status change” is
detected. The thermal table would switch to laptop mode or lid close
mode.
Once the higher environment temperatures are detected,the thermal
table would switch to the corresponding power throttle table (B, D or
F). Based on these table switching mechanisms, no matter how the
end-user uses Chromebook,they could enjoy more humanized thermal
designs.
Release Over Over Release .
Temp. Temp. Temp. Temp. .
-------------------------------------------------------- .
Desktop mode Table A Table B 50C 45C .
Lid open (Default) .
-------------------------------------------------------- .
Desktop mode Table C Table D 55C 50C .
Lid close .
-------------------------------------------------------- .
Laptop mode Table E Table F 45C 40C .
-------------------------------------------------------- .
On the proposal, the transmission rules are list below:
1. Table A is the default table after booting.
2. A, C, E (Release Temp) can switch to each other.
3. B, D, F (Over Temp) can switch to each other.
4. A and B, C and D, E and F can switch to each other.
5. If Lid open/close or mode switch event trigger, temperature release
tables will translation to each other, temperature over tables will
translation to each other.After that event trigger, EC will check the
new temperature condition and decide if the temperature need to be
trigger.For example, if table A will switch to table D, table A will
switch to C with Lid close event, if temperature is over 55C, EC will
trigger temperature to switch form table C to D.
6. EC will trigger 3 times body-detection events during power on boot
without any body-mode and lid status change. For this case if the
previous table label is on same group, we will based on the temperature
to decide the table.
For example, assume table A is current table. When the temperature
reaches 50C, than the table is switched from A to B. The current table
is B. When the temperature is downgrade below 45C, the table is
switched form B to A. The same rule is for C and D, E and F.
BRANCH=none
BUG=b:232946420
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: I866e5e497e2936984e713029b5f0b6d54cbc9622
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Include <amdblocks/gpio_defs.h> instead of "gpio_defs.h", since
gpio_defs.h is not only visible in a local scope, but also as
<amdblocks/gpio_defs.h>.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab3e5bb235a5b1bc995b6cf8710f0d8c1886142d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70432
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This avoids the need to hardcode the IOAPIC ID.
Change-Id: I0965b511e71c58f1c31433bc54595a5fabb1c206
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70268
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
There are four requirements for the SMI to hit a printk()
this commit now removes.
Build must have DEBUG_SMI=y, otherwise any printk() is a no-op
inside SMM.
ASL must have a TRAP() with argument 0x99 or 0x32 for SMIF value.
Platform needs to have IO Trap #3 enabled at IO 0x800.
The SMI monitor must call io_trap_handler for IO Trap #3.
At the moment, only getac/p470 would meet the above criteria
with TRAP(0x32) in its DSDT _INI method. The ASL ignores any
return value of TRAP() calls made.
A mainboard IO trap handler should have precedence over
a southbridge IO trap handler. At the moment we seem to have
no cases of the latter to support, so remove the latter.
Change-Id: I3a3298c8d9814db8464fbf7444c6e0e6ac6ac008
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
At the moment IO trap is not implemented for AMD platforms.
Change-Id: Ib62ac4e4e418a8bab80c30dfb5183ecd8beb998d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is more robust than hardcoding whathever FSP has set up and is a
lot less code.
Change-Id: I6423ddc139d742879d791b054ea082768749c0a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70265
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SOC_INTEL_CSE_SEND_EOP_EARLY breaks soft ME disable, which works using
a HECI message that needs to be sent before EOP. Make the option
configurable to allow soft ME disable on alderlake.
Change-Id: I7febf7c029e7eac94052cc3a8142949d6813c1bc
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This replaces the mechanism with --ext-win-base --ext-win-size with a
more generic mechanism where cbfstool can be provided with an arbitrary
memory map.
This will be useful for AMD platforms with flash sizes larger than 16M
where only the lower 16M half gets memory mapped below 4G. Also on Intel
system the IFD allows for a memory map where the "top of flash" !=
"below 4G". This is for instance the case by default on Intel APL.
TEST: google/brya build for chromeos which used --ext-win-base remains
the same after this change with BUILD_TIMELESS=1.
Change-Id: I38ab4c369704497f711e14ecda3ff3a8cdc0d089
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Do not hide UARTs in ACPI mode from the OS, as this prevents using them
on at least Windows. Currently, the driver is only used on the Prodrive
Hermes mainboard.
Change-Id: I01bdccff1b11e1862970c924fd5fc7718a2d6ce9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70155
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `HyperThreading` FSP UPD is set according to the `hyper_threading`
CMOS option using the value of the `FSP_HYPERTHREADING` Kconfig option
as fallback in case options are disabled or otherwise unavailable. The
`HyperThreadingDisable` devicetree setting isn't used by any mainboard
but it overwrites the value of the FSP UPD. Remove it so that the CMOS
and Kconfig options work as intended.
Change-Id: Iea60b89f6f970eb9aee8c7bec026ab5c2df30205
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69534
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fixing documentation of PAD_INT macro and replacing spaces with a tab to
match the rest of the documentation.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I72a2578ce21dd10b3beb65c706440c3379f216d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70281
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The DSI CMDQ offset of MT8186 is different from previous SoCs.
Therefore, we define two versions for DSI register header files. The v1
is for MT8173/MT8183/MT8192 and the v2 is for MT8186/MT8188.
BUG=b:244208960
TEST=build pass
BRANCH=corsola
Change-Id: I3d13ca03b72554ab7be2b194db32a4f961f38dad
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70183
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For geralt project, we also support MIPI panel as our firmware display.
So add this patch to configure ddp to choose eDP display or MIPI panel
display.
BUG=b:244208960
TEST=test firmware display pass for both eDP and MIPI panel on MT8188
EVB.
Change-Id: I06f38b1889811274588c26e9284da4d502acf38b
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70181
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will avoid clearing the other bits in fifo_status.
Change-Id: I7917b3f8d9af6056ed872b7e48cef9c3deba5119
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The devices in the list that was introduced in commit c66ea98577
("soc/intel/alderlake: provide a list of D-states to enter
LPM") are all internal. This CL skips the external buses (which caused
the addition of packages to non-existant paths such as
"_SB.PCI0.RP1.MCHC", and warnings from the kernel)
BUG=b:231582182
TEST=Built and tested on anahera by verifying SSDT contents
Change-Id: I3785b2b2af85d96e2e1296b6cfdefcd72080b5fe
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70163
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This patch selects SOC_INTEL_CSE_SEND_EOP_LATE config to let IA
common code to skip sending CSE EOP cmd during finalize operation
rather uses boot state machine (either payload load or payload boot)
to delay in sending EOP cmd to CSE.
BUG=b:260041679
TEST=Able to boot to Google/Rex with this patch and observed ~150ms
savings in boot time
Without this patch:
942:before sending EOP to ME 1,795,702 (354)
943:after sending EOP to ME 1,950,526 (154,824)
With this patch:
942:before sending EOP to ME 2,051,406 (35,484)
943:after sending EOP to ME 2,057,583 (6,177)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7d44d5eff890ac78e3075d49cc249f740686dd0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69999
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch allows to send late EOP cmd to CSE (after CSE .final)
using boot state machine (either BS_PAYLOAD_BOOT or BS_PAYLOAD_LOAD)
if the SoC user selects SOC_INTEL_CSE_SEND_EOP_LATE config.
Rename `set_cse_end_of_post()` to `send_cse_eop_with_late_finalize()`
to make the function name more meaningful with its operation.
BUG=b:260041679
TEST=Able to boot Google/Rex after sending CSE EOP late.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: If4c4564befcd38732368b21f1ca3e24b68c30e0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
This patch creates an API that can perform essential CSE operation
after sending the late EOP command to the CSE and prior booting to OS.
Lists of operation are
- Perform global reset lock
- Put HECI1 to D0i3 and disable the HECI1 if the user selects
- Set D0I3 for all HECI devices.
BUG=b:260041679
TEST=Able to boot Google/Rex after sending CSE EOP late.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I10131ea9b553a62f0d632783c4dbad96d35d6563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69977
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch refactors common code to allow cse_final() function to send
EOP cmd if the SoC user selects `SOC_INTEL_CSE_SET_EOP` kconfig.
This patch helps cse_final_ready_to_boot() and
cse_final_end_of_firmware() function for being meaningful with its
operation and let cse_final() being that outer layer to perform three
operations based on the selected kconfig.
1. send cse eop command
2. perform cse_final_ready_to_boot() operations
3. perform cse_final_end_of_firmware() operations
Additionally, ensures the platform that choose to send EOP late
(like JSL and TGL) is not being impacted due to this code refactoring
hence, skip calling into CSE.final if SoC selects
`SOC_INTEL_CSE_SEND_EOP_LATE` config.
BUG=b:260041679
TEST=Able to send EOP command successfully for Google/Taeko.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I412291c9378011509d3825f9b01e81bfced53303
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69975
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Presently, coreboot supports two instances of sending EOP cmd to
the Intel CSE.
1. Sending EOP cmd to CSE during `.final` operation from cse pci driver.
2. Starting with Alder Lake, the recommendation was to send EOP to CSE
earlier than CSE `.final` operation. Since then it's referred to as
`Sending EOP Early`. This method helped to save the CSE EOP
response time significantly.
During Meteor Lake platform, CSE EOP response time has become
non-deterministic and we have figured that sending EOP command later
than CSE .final operation is actually helping to optimize the boot time
significantly (around ~150ms savings compared to sending from `.final`
ops and ~5sec compared to sending CSE early).
Hence, this patch intended to create yet another kconfig for sending
CSE late (specifically after `.final` operation). The idea for this
newer config is to use the boot state machine for sending CSE EOP cmd.
The patch train in this series would add the specific changes to allow
sending EOP late and perform other essential operations required prior
booting to OS as coreboot decided to skip calling into FSP Notify phase.
Starting with Jasper Lake, coreboot sends EOP before loading payload
hence, this config is applicable for those platforms.
The current plan is that Intel Jasper Lake, Tiger Lake and Meteor Lake
platform will select this newer config from SoC code.
BUG=b:260041679
TEST=Able to send EOP command successfully for Google/Taeko.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iea512cd5b79d61dd5d5a962079baf525027c831f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69976
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures dropping of the duplicate macro introduced with
'commit 9e4488ab06 ("soc/intel/{adl,cmn}: Add/Remove LTR
disqualification for UFS")'
`PCH_PWRM_BASE_SIZE` macro represents the size of the PMC MMIO range
which can be used as is even in ufs.asl file.
BUG=b:252975357
TEST=Build and boot nirwen and see no issues in PLT runs.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic967c609e1330eca1b9e1143e7efd78db011f317
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70180
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
The patch logs CSE RO's write protection information for Meteor Lake
platform. As part of write protection information, coreboot logs status
on CSE RO write protection and range. Also, logs error message if EOM
is disabled, and write protection for CSE RO is not enabled.
Port of commit abe0d810f0 ("soc/intel/alderlake: Log CSE RO write
protection info for ADL").
BUG=none
TEST=Verify the write protection details on google/rex.
Excerpt from google/rex coreboot log:
[DEBUG] ME: WP for RO is enabled : YES
[DEBUG] ME: RO write protection scope - Start=0x4000, End=0x396FFF
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Idb072a873a8b8323532799f5fc64f995c9f0a604
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
This reverts commit 095c931cf1.
Previously cpu_info() was implemented with a struct on top of an
aligned stack. As FSP changed the stack value cpu_info() could not be
used in FSP context (which PPI is). Now cpu_info() uses GDT segments,
which FSP does not touch so it can be used.
This also exports cpu_infos from cpu.c as it's a convenient way to get
the struct device * for a certain index.
TESTED on aldrvp: FSP-S works and is able to run code on APs.
Change-Id: I3a40156ba275b572d7d1913d8c17c24b4c8f6d78
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69509
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The coreboot CPU index for a lapic is arbitrary: it depends on which
CPU obtains a spinlock first. Simply using an increasing index will
result in consistent ACPI tables across each boot.
Change-Id: Iaaaef213b32b33e3ec9f4874d576896c2335211c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69510
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Name a variable based on its utility. `is_external` variable adds
`ExternalFacingPort` _DSD property to an ACPI device hence
rename it to `add_acpi_external_facing_port`.
BUG=b:259716145
TEST=Build google/rex with this flag and verify it in SSDT at
runtime.
SSDT snippet:
Name (_DSD, Package (0x04) // _DSD: Device-Specific Data
{
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package (0x01)
{
Package (0x02)
{
"HotPlugSupportInD3",
One
}
},
ToUUID ("efcc06cc-73ac-4bc3-bff0-76143807c389"),
Package (0x01)
{
Package (0x02)
{
"ExternalFacingPort",
One
}
}
})
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I65100283ed9b65037c9890f28ecab41fcfa25d83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69970
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The message only makes sense if ACPI PM base address is
allowed to be dynamic. If requested, it can be logged
in common code.
Change-Id: Iad7a60098c0391cc23384035af49e373dad90233
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Later soc/intel/common/smbus addresses TCO2_STS as a separate
16-bit register, while baytrail and braswell assumes 32-bit
wide TCO1_STS to extend as TCO2_STS.
In src/soc/intel/denverton_ns:
#define TCO2_STS_SECOND_TO 0x02
In soc/intel/baytrail,braswell:
#define SECOND_TO_STS (1 << 17)
Elsewehere
#define SECOND_TO_STS (1 << 1)
It's expected that we remove the first (1 << 17) case and only
access TCO2_STS as a separate 16-bit register. For now, use
unique names to avoid confusion.
Change-Id: I07cc46a9d600b2bf2f23588b26891268e9ce4de0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tree is inconsistent with the use of TCO register space offsets and
related preprocessor defines. The legacy space was offset from ACPI
PM base by 0x60, but this changed with later platforms. The convenient
way is to define the TCO registers relative to its base address and
subtract 0x60 here, but this change cannot be easily done tree-wide or
in one go.
For the transient period, apply TCO_SPACE_NOT_YET_SPLIT flag until
all platforms use a clean style of tco_{read,write} accessor functions
instead of {read,write}_pmbase16(), or worse, inw/outl().
Change-Id: I16213cdb13f98fccb261004b31e81a9a44cb6e3b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch drops the local implementation
`log_me_ro_write_protection_info` and adopts the API from IA common
code (cse_lite.c).
BUG=none
TEST=Able to compile the cse_lite.c file for google/kano without
any error.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I087ffb8ac94f14a6bd7f2bf6bb907c4047dc9899
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69969
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This patch creates an API for CSE-Lite specific SKU to retrieve the
Write Protect (WP) information (`cse_log_ro_write_protection_info`)
like WP range and limit, if the region is write-protected or not etc.
BUG=none
TEST=Able to compile the cse_lite.c file for google/kano without
any error.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8f4b7880534ded5401b6f8d601ded88019c636c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69968
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
These boards do no fill MADT with useful information.
Change-Id: Ie61e4e4b03c9b7fcd70aba7a2bd71eadd6f4dab1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69777
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The cpu cluster is always present and it's the proper device to contain
the settings that need to be applied to all cpus. This makes it possible
to remove the fake lapic from devicetrees.
Change-Id: Ic449b2df8036e8c02b5559cca6b2e7479a70a786
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59314
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Set of boards and platforms did not have LINT1 configured
as NMI source.
Change-Id: I65044125562bda363b3a0d92da6137c77a28b587
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69528
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the broadcast ID to deliver LINT1 as NMI to all CPUs,
instead of listing individual LAPIC IDs.
Change-Id: Iaf714d8c2aabd16c59c3bcebc4a207406fc85ca9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
A previous CL ("Add missing ACPI device path names",
commit d22500f0c61f8c8e10d8f4a24e3e2bf031163c07) caused some errors
from the Kernel on Brya devices (see Tim's comment on patchset 8):
> ACPI Error: AE_NOT_FOUND, While resolving a named reference
> package element - \_SB_.PCI0.FSPI
FSPI is defined in src/soc/intel/alderlake/chipset.cb:
device pci 1f.5 alias fast_spi on end
This CL adds the corresponding FSPI device to the DSDT to prevent
the error mentioned above.
TEST=Built and tested on brya by verifying the error is gone.
BUG=b:231582182
Change-Id: I11e89ad2a5d47f6b579f755b0a41399ee3cb856c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69920
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the most part, this doesn't change any post codes, simply making the
existing post-codes into macros.
picasso/romstage.c did get a couple of post codes removed to match the
other files.
The POST_ROMSTAGE and POST_BOOTBLOCK codes are intended to become global
at some point, while the POST_AGESA and POST_PSP codes would stay AMD
specific.
Change-Id: I007a09b6a3ed3280bac674cd74e298ec5c408ab7
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch decouples HECI disabling interface a.k.a SMM or PCR or PMC
IPC etc. from DISABLE_HECI1_AT_PRE_BOOT kconfig as Intel ME BWG
recommends to disable the CSE PCI device while CSE is in
software temporary disable state.
BUG=b:260183610
TEST=Able to build google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3c9c5a73028cde90af3553093a13d0c05b831bae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69930
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch refactors the MDIO access for the TSN GbE device by placing
the MDIO read and write functions into mdio_bus_operations struct which
is assigned to the .ops_mdio member of the PCI device struct. In this
way the MDIO interface of the TSN GbE device is exposed and can be used
by other drivers if needed.
Change-Id: I5d1b9dd2f2ba8c18291fff314c13f0c3851784aa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch skips setting D0I3 bit for all HECI devices by FSP.
The learning being made from Alder Lake platform showed that the CSE
EOP cmd response time is highly nondeterministic and letting the EOP
cmd issued by FSP makes the response time even worse.
The idea being pursued during Alder Lake platform is to let FSP skip sending the EOP cmd and coreboot sends it at the last minute
(late sending of EOP) to ensure there is ample time for CSE to come
to a state where the response to the EOP is almost immediate.
There were a number of refactoring being done to ensure the EOP cmd
can be sent at the later stage.
#1: Ensure FSP is not putting those HECI devices into the D0i3. (SoC specific change)
#2: Modify the CSE related boot state based operation to allow a
proper window for sending late EOP cmd. (Common Code Specific change)
The entire refactoring helps us to save ~60ms of boot time.
Without those code change EOP sending timestamp as below:
943:after sending EOP to ME 1,248,328(61,954))
With those code change EOP sending timestamp as below:
943:after sending EOP to ME 1,231,660 (2,754)
Port of commit d6da4ef69e ("soc/intel/alderlake: Skip setting D0I3
bit for HECI devices") to incorporate the #1 which is a SoC specific
code change.
BUG=none
TEST=FSP-S UPD dump suggested `DisableD0I3SettingForHeci` UPD is
set to `1`.
Excerpt from google/rex coreboot log:
[SPEW ] DisableD0I3SettingForHeci : 0x1
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I1c3765ce41f192ab5f5ff176e0a2b49b312d18d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Update the fields that need to be updated directly in the local static
usb_phy_config struct instead of dereferencing the pointer written to
the corresponding UPD field. This will allow updating the type of UPD
field in a follow-up commit to enable 64 bit coreboot builds.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I44a9fe719e6803fc957fee3db13b261489ed313d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69896
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
This ports forward part of commit df09680626 ("soc/amd/picasso: Add
support for 64bit builds") to the newer AMD SoCs.
Use -Wl instead of -l to get the output format that the commands in the
Makefile expect to extract the value for PSP_BIOSBIN_SIZE. Without this
change, readelf will split the output into two lines in case of a 64 bit
coreboot build. This results in invalid amdcompress and amdfwtool
command lines which will cause the amdfwtool call to fail with
Error: BIOS binary destination and uncompressed size are required
With the old readelf -l command we get this output in a 64 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000080 0x0000000002030000 0x0000000002030000
0x0000000000010000 0x0000000000010000 RWE 0x10
while we get the correct output in a 32 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000060 0x02030000 0x02030000 0x10000 0x10000 RWE 0x20
With readelf -Wl we also get the expected output in a 64 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000080 0x0000000002030000 0x0000000002030000 0x010000 0x010000 RWE 0x10
TEST=This fixes the 64 bit build on Cezanne with some follow-up patches
applied.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I35f9feda4d0da3546592dfac233ca66732bd5464
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69895
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Skip eDP initialization when we failed to get EDID. This prevents the
PLL assertion in dp_intf_config() if the display could not be
initialized properly.
BUG=b:233720142
TEST=boot to depthcharge on MT8188 EVB.
Change-Id: I0fd672b175feb9b813c1d9ec4140e4273079ff07
Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69858
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch helps to save 10.200ms of booting time without any issue
seen during MP Init. All cores are out from reset and alive.
Port the Alder Lake 'commit 6526e78967 ("soc/intel/alderlake: Select X86_INIT_NEED_1_SIPI Kconfig for RPL")' also to Meteor Lake.
Additionally, no performance degradation is observed while running
benchmarks.
BUG=b:211770003
TEST=Able to boot Google, Rex to ChromeOS with all cores enabled.
Without this patch:
30:device enumeration 1,480,217 (28,232)
With this patch:
30:device enumeration 1,472,466 (18,334)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iec21470b9b34514169789c39bdc3be4e4ff6c7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69851
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the most part, this just moves the existing post codes into macros
so that they're not just bare numbers.
cache_as_ram.S:
Post code 0x28 was previously pointless with just a single jump between
it and post code 0x29, car_init_done. This code was removed, and the
0x28 value was used to differentiate the car_nem_enhanced subroutine
from the other 0x26 post codes used before calling the clear_car
subroutine.
All other post codes remain identical.
POST_BOOTBLOCK and POST_CODE_ZERO are expected to become global, whereas
the POST_SOC codes are expected to be Intel only.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I82a34960ae73fc263359e4519234ee78e7e3daab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69865
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBFS_MCACHE is currently experiencing overflow with CBFS verification
enabled. Reduce the pre-x86 cbmem console size from ~5.5 KiB to 4 KiB.
This reduction along with the available free space in PSP shared buffer
(32 KiB) helps to increase the CBFS_MCACHE size from 8 KiB to required
14 KiB.
BUG=b:259342909
TEST=Build and boot to OS in Skyrim. Ensure that there are no CBFS
mcache overflows.
FMAP: area COREBOOT found @ 80a000 (8347648 bytes)
VB2:vb2_digest_init() 0 bytes, hash algo 2, HW acceleration unsupported
CBFS: mcache @0x00019a40 built for 67 files, used 0x19a0 of 0x1c00 bytes
CBFS: Found 'apu/amdfw_a' @0x0 size 0x3ff80 in mcache @0x0001b640
VB2:vb2_digest_init() 262016 bytes, hash algo 2, HW acceleration enabled
Ensure that firmware_CbfsMcache FAFT test is successful.
Change-Id: I35e1a8c6d73e0870b6a43aac604f83a0b6c3aabe
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69827
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The patch parses CPU and PCH Trace Hub modes from the debug area in the
Descriptor Region. The modes can be updated in the debug area in order
to configure the CPU and PCH Trace Hub modes. The debug area's offset
starts from the SPI Flash offset:0xf00.
For runtime debugging, the OEM Section in the Descriptor Region is being
used as debug area. The OEM Section details are documented in the SPI
Programmer Guide of CSE Lite kit.
TEST=Build code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I61241c5c1981ddc4b21581bb3ed9f531da5f41b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
After DisplayPort is plugged into type-C port, its hpd signal
instantly presents and EC has mux_info for dp and hpd. This change
fixes the DP detection flow to avoid the 1 second delay while no DP
is connected. If DP is present, there will be requests towards PMC
through the sequence of connect, safe mode, dp and hpd mode.
BUG=b:247670186
TEST=Built image and validated the DisplayPort preboot feature on Rex.
Change-Id: I7cb95ec7fcc7e1a86e86466e6d45390eedcc4531
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Set `EnableTcoTimer=1` in order to keep FSP from
1) enabling ACPI Timer emulation in uCode.
2) disabling the PM ACPI Timer.
Both actions are now done in coreboot.
`EnableTcoTimer=1` makes FSP skip these steps in any possible case
including `SkipMpInit=0`, `SkipMpInit=1`, use of the MP PPI or FSP
Multiphase Init. This way full control is left to coreboot.
Port of commit 0e905801f8 ("soc/intel: transition full control over PM
Timer from FSP to coreboot").
NOTE: This will have a huge power impact when it's enabled. If TCO timer
is disabled, uCode ACPI timer emulation must be enabled, and WDAT table
must not be exposed to the OS.
BUG=none
TEST=Boot to OS on google/rex.
Excerpt from google/rex coreboot log:
[SPEW ] EnableTcoTimer = 1
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I2693f0390e6c9fa92fec366ab87589c3bcea9027
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Get rid of a lot of casts.
Change-Id: I93645ef5dd270905ce421e68e342aff4c331eae6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Update acpigen_write_alib_dptc() to support extra 5 thermal profiles.
User can use these profiles for dynamic thermal table switching support.
BUG=b:232946420
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: I9e6d5c0fc6f492340c935899920d9ee7c9396256
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68470
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Issue:
Device can't wake up using power key.
Root cause and solution:
EINT event mask register is used to mask EINT wakeup sources. All
wakeup sources are masked by default. So we add a driver here to unmask
all wakeup sources.
BUG=none
TEST=wake the device up by power key on MT8188 EVB.
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Change-Id: I94b20909b0b8d77f75c41bc745f892baded7a54b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69688
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
On Herobrine, we will determine if we have an NVMe device based on SKU
id. Basically, if bit 0 is 2 (or Z), then we know that we have an
NVMe device and thus will need to go through PCIe initialization.
Otherwise, we know that we are booting an eMMC device.
BUG=b:254281839
BRANCH=None
TEST=build firmware image and boot and make sure we can boot up Tested
on villager, which does not have NVMe and made sure that it boots
still. Check cbmem dump to make sure that device configuration
entry is still low since it's not initializing PCIe devices:
40:device configuration 730,203 (1,295)
Change-Id: I1fa0ad392ba6320fdbab54b3b5dc83ac28cd20ba
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69690
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement mainboard_needs_pcie_init() for herobrine in order to
determine if we need to initialize the pcie links. When the SKU id is
unknown or unprovisioned (for example at the beginning of the factory
flow), we should still initialize PCIe. Otherwise the devices with
NVMe will fail to boot.
BUG=b:254281839
BRANCH=None
TEST=emerge-herobrine coreboot
Change-Id: I8972424f0c5d082165c185ab52a638e8b134064c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The dimm_info structure (defined in src/include/memory_info.h)
currently does not hold information about the DIMM's
node/controller ID.
This patch extends the dimm_info structure by adding a new field for
the node ID, called node_num. Also, adapt the dimm_info_fill()
function accordingly to populate the newly-added field.
Background: These changes are necessary for the Atlas mainboard, where
we are currently experiencing issues with the DIMMs device/bank
locator. Our 2 DIMMs share the same CHANNEL and DIMM ID but have a
distinct NODE ID. By looking at the smbios table we see
Channel-0-DIMM-0 for both DIMMs. Thus, we need their NODE IDs in order
to distinguish them.
This patch was tested by building and booting for the Alderlake-P
RVP board, which has the same DIMM slot configuration as the
Prodrive Atlas mainboard.
Signed-off-by: David Milosevic <David.Milosevic@9elements.com>
Change-Id: I6ffa5bdff0ba0e3c4a4a51f2419291fd1278cd68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68525
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
default SOC_INTEL_COMMON_BLOCK_SGX_PRMRR_SIZE value is missing by
accident for SOC_INTEL_COMMON_BLOCK_SGX_PRMRR_SIZE_32MB.
Change-Id: Ib3af0a1c509ab2e2eccf3e36ff604a1040995af4
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69332
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
It is no longer necessary to explicitly add "Warning" in front of
BIOS_WARNING message.
Change-Id: If1645180dd98ff5a1661fd568554de5831ef237e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69623
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per Intel doc #627331 Section 3.6.1 "Intel CSME Production Machine
Determination", from ADL onwards there are three criteria which
determine whether a device is in production mode:
1. Fuses are programmed
2. SPI descriptor is locked
3. Manufacturing variables are locked
When logging whether the device is in manufacturing mode, 1 and 2 are
already checked. Add a check for 3 as well.
Also add logs for each individual criteria so it's easy to tell why the
overall Manufacturing Mode is set or not.
BUG=b:255462682
TEST=On a nivviks which has not gone through EOM:
Before:
[DEBUG] ME: Manufacturing Mode : YES
[DEBUG] ME: SPI Protection Mode Enabled : NO
After:
[DEBUG] ME: Manufacturing Mode : YES
[DEBUG] ME: SPI Protection Mode Enabled : NO
[DEBUG] ME: FPFs Committed : NO
[DEBUG] ME: Manufacturing Vars Locked : NO
On an anahera which has gone through EOM:
Before:
[DEBUG] ME: Manufacturing Mode : NO
[DEBUG] ME: SPI Protection Mode Enabled : YES
After:
[DEBUG] ME: Manufacturing Mode : NO
[DEBUG] ME: SPI Protection Mode Enabled : YES
[DEBUG] ME: FPFs Committed : YES
[DEBUG] ME: Manufacturing Vars Locked : YES
Change-Id: Iac605baa291ab5cc5f28464006f4828c12c748fe
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69324
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update Alder Lake CSME HFSTS registers definitions as per Intel
doc #627331 revision 1.0.0, section 3.4.8.
Follow up CLs will use the bit definitions for performing
various checks.
TEST=build and boot nivviks platform
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I9aeee7a3b41ad59c03391207930a253ffff19ae5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69286
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 1b07797a7b.
Reason for revert: Herobrine program decided that we wanted
to be able to boot from NVMe if one exists.
Change-Id: If675947026095d16b72bdb0f3ec790e583523465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69719
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per Intel doc #729124 Section 3.6.1 "Intel CSME Production Machine
Determination", from ADL onwards there are three criteria which
determine whether a device is in production mode:
1. Fuses are programmed
2. SPI descriptor is locked
3. Manufacturing variables are locked
When logging whether the device is in manufacturing mode, #1 and #2 are
already checked. Add a check for #3 as well.
TEST=Build and boot MTL RVP
Snippet from coreboot log:
[DEBUG] ME: Manufacturing Mode : YES
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I495a7d8730716fc92e8c57b2caef73e8bb44d30b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
The patch updates HFSTS4, HFSTS5 & HFSTS6 register definitions as per
MTL Intel CSME BIOS Specification (doc# 729124). Also, the patch logs
the firmware status details as per the new register definition.
TEST=Build and boot the coreboot on Rex
Snippet from coreboot log with the patch:
[DEBUG] ME: CPU Debug Disabled : NO
[DEBUG] ME: TXT Support : NO
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ibee9a0955efc22ea0d9fdbba2d09e57d8851e22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69577
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hide these ACPI device so Windows does not warn about missing device
drivers.
Port of commit 907c85ad48 ("soc/intel/alderlake: Hide PMC and IOM
devices").
BUG=none
TEST=Verified _STA method from ACPI tables in OS. USB-C drive is
detected in OS.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ic62172bee9120d260a3cd60770ef780cb7dce860
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69576
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update header files for FSP for Meteor Lake platform to
version 2404_00, previous version being 2364_00.
FSPM:
1. Address offset changes
2. Rename `PlatformDebugConsent` to `PlatformDebugOption`
FSPS:
1. Address offset changes
Additionally, incorporate the UPD name change for MTL romstage.
BUG=b:255481471
TEST=Able to build and boot Google, Rex to ChromeOS.
Signed-off-by: vjadeja-intel <vikrant.l.jadeja@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I63ef4ecb6569141542a3b9bf4ee8cbcd2946582e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Remove TODO comments after reviwing against morgana ppr #57396, rev 1.52
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I598daf40a774ec81a956ce8c1aeb1cbbf4b475f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69275
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Not all functions that call fsp_print_guid print their output with the
BIOS_SPEW log level, so introduce a new log level parameter so that the
caller of fsp_print_guid can specify which log level fsp_print_guid
should use for printing the GUID.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3b37afe703f506d4913f95a954368c0eec0f862d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69599
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clang doesn't understand the -Wstack-usage=40960 option. Replace it
with -Wframe-larger-than=40960.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I7d8b9c26d3fc861615a8553332ed1070974b751b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch uses index 0x10 for IOE P2SB memory resource allocation
instead of static 0.
Additionally, switches to `mmio_resource` from `mmio_resource_kb`.
TEST=Able to build and boot Google/Rex and observed log as below.
Without the code change:
[SPEW ] PCI: 00:13.0 resource base 3fff0aa0000 size 1400 align 0
gran 0 limit 0 flags f0000200 index 0
With the code change:
[SPEW ] PCI: 00:13.0 resource base 3fff0aa0000 size 1400 align 0
gran 0 limit 0 flags f0000200 index 10
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I44caac73e245f536f3a22baafa1a6a0370e1dd37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested on google/vilboz (running the PCI rom with yabel).
Change-Id: Icd72c4eef7805aacba6378632cbac7de9527673b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Now that we have a common init_tables in all mainboards using AMD SoCs,
both the population of the fch_pic_routing and fch_apic_routing arrays
and the definition of those arrays can be moved to the common AMD SoC
code to not have the code duplicated in all mainboards.
BUG=b:182782749
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: I8c65eca258272f0ef7dec3ece6236f5d00954c66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68853
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Explicitly cast integers to fix building for long mode.
Change-Id: I9f56e183563c943d1c2bd0478c41a80512b47c5e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use the newly added functions to iterate over the FSP HOBs to report the
resources used by FSP to the resource allocator instead of open coding
the iteration over the HOBs in the SoC code.
TEST=Patch doesn't change reported resources on Mandolin
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I67ca346345c1fa08b008caa885d0a00d2d5afb12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use VBOOT_STARTS_BEFORE_BOOTBLOCK to determine whether the VERSTAGE
needs to be build as x86 stage.
Change-Id: I126801a1f6f523435935bb300f3e2807db347f63
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
On newer AMD platforms, mb_pre_fspm() is used to set GPIOs in romstage
for PCIe reset (currently set in bootblock) and touchscreen power
sequencing (not yet implemented, but will be later in the patch train).
Change-Id: Ia422aaa9e80355f9a9f8f850368441e5c8ff6598
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69452
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For extern ethernet PHY access it is necessary to enable the 'scan_bus'
functionality.
Change-Id: I88050df2059ec7e0b27a132bca626eaef3d5dfb0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69385
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This replaces 'SPDX-License-Identifier' tags in all the files under
soc/mediatek/mt8195 for better code re-use in other open source
software stack.
These files were originally from MediaTek and follow coreboot's main
license: "GPL-2.0-only". Now MediaTek replaces these files to
"GPL-2.0-only OR MIT" license.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Change-Id: I79a585c2a611dbfd294c1c94f998d972118b5c52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66625
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
This makes it easier to get the content of an msr into a full 64bit
variable.
Change-Id: I1b026cd3807fd68d805051a74b3d31fcde1c5626
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68572
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When no HOB list is found, not only adding the resources reported by the
FSP were skipped, but also adding the GNB IOAPIC resource was skipped.
Fix this bug by moving the reporting of the GNB IOAPIC resource before
the resources reported in the FSP HOBs to not skip the IOAPIC resource
when there's no HOB list.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9174c8d7e5e94144187d27210e12f2dca3a6010f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69460
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is no longer necessary to explicitly add "ERROR: "/"WARNING: " in
front of every BIOS_ERR/BIOS_WARN message.
Change-Id: I22ee6ae15c3d3a848853c5460b3b3c1795adf2f5
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
to soc
Move SMBIOS type 4 override functions from mainboard to soc so that all
xeon family cpus share same functions without implementing again.
Tested=On OCP Deltalake, dmidecode -t 4 shows expected info.
Signed-off-by: JingleHsuWiwynn <jingle_hsu@wiwynn.com>
Change-Id: I17df8de67bc2f5e89ea04da36efb2480a7e73174
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
This kind of allocation without '=' is not working with clang.
Change-Id: I2d3e9eb44c3e0e25e5a67c5386e5ddde1487cc74
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63063
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It looks like this code was not finished so it's left commented out
for now.
Change-Id: I442a42e297f2968dd2c824a93a9a1e2bc74ea2f4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63074
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit factors out `struct xhci_usb_info` from intel specific code
as it will be useful on other platforms.
BUG=b:186792595
TEST=Builds for volteer
Change-Id: I5b4cc6268f072c6948f11c7498a564d7a5c0a190
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
This commit factors out some code for XHCI port status values.
BUG=b:186792595
TEST=Built coreboot for volteer device
Change-Id: I045405ed224aa8f48f6f628b7d49ec6bafb450d7
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Instead of including pci_int_defs.asl in each board's DSDT, include it
in the common soc.asl. This moves the PRQM OperationRegion and the PRQI
IndexField defined in pci_int_defs.asl into the \_SB scope, but those
are defined inside the \_SB scope both in the Picasso reference code and
for the AMD SoCs from Cezanne on.
TEST=Both Linux and Windows still boot and don't show ACPI errors on
Mandolin after moving this inside the \_SB scope
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib4e7bfb15de184cc43cd17c8249be0f59405793f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
This aligns Picasso more with the newer AMD SoCs and also makes it a bit
clearer what this file does. Also remove the unneeded tabs at the
beginning of each line.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie6e5ee815e4346004bc864a6111a255dc689eae8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
According to measurements Elkhart Lake seems to drive the internal I2C
controllers with 100 MHz instead of the common 133 MHz. The datasheet
itself is quite vague on this definition, just one place mentions that
it is 100 MHz (register description for offset 0x94).
This patch changes the I2C controller base frequency to 100 MHz. The
verification was done by measuring the set up resulting I2C clock for
both 100 and 400 kHz.
Change-Id: I7c826bbb01b53e3661746e49f25441565068d1c2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
On certain mainboards due to hardware design limitations, certain SPI
Read Modes eg. (Dual I/O 1-2-2) cannot be supported. Add ability to
override SPI read modes in boards which do not have hardware
limitations. Currently there is an API to override SPI fast speeds.
Update this API for mainboards to override SPI read mode as well.
BUG=b:225213679
TEST=Build and boot to OS in Skyrim. Observe a boot time improvement of
~25 ms with 100 MHz SPI speeds.
Before:
11:start of bootblock 688,046
14:finished loading romstage 30,865
16:FSP-M finished LZMA decompress (ignore for x86) 91,049
Total Time: 1,972,625
After:
11:start of bootblock 667,642
14:finished loading romstage 29,798
16:FSP-M finished LZMA decompress (ignore for x86) 87,743
Total Time: 1,943,924
Change-Id: I160b56f6201a798ce59e977ca40301e23ab63805
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
This patch introduces support signing and verification of firmware
slots using CBFS metadata hash verification method for faster initial
verification. To have complete verification, CBFS_VERIFICATION should
also be enabled, as metadata hash covers only files metadata, not their
contents.
This patch also adapts mainboards and SoCs to new vboot reset
requirements.
TEST=Google Volteer/Voxel boots with VBOOT_CBFS_INTEGRATION enabled
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I40ae01c477c4e4f7a1c90e4026a8a868ae64b5ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66909
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel FSPs of XEON server platforms define FSPX_CONFIG
instead of FSP_X_CONFIG, which is expected by coreboot.
Re-define in the common code.
Update coreboot code to use FSP_X_CONFIG consistently.
Tested=On OCP Delta Lake, boot up OS successfully.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: Ifa0e1efa1618fbec84f1e1f23d9e49f3b1057b32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch groups vboot context, recovery reason and subcode saving, and
reboot calls into two handy functions:
- vboot_save_and_reboot() - save context and reboot
- vboot_fail_and_reboot() - store recovery reason and call function
above
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ie29410e8985e7cf19bd8d4cccc393b050ca1f1c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69208
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Disable Pch PM Energy Report WA was added to enhance boot time
with HFPGA only. SoC needs reporting enabled.
BUG=None
TEST=Build and Boot Google, Rex and Intel, MTLRVP without any boot time regression..
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: If5f1f9c6ab31652977d436a49a3531edffbd60c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69042
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
This patch replaces static index 0 for PMC read resources with PCI
configuration offset 0x10 (PWRMBASE).
TEST=Able to build and boot Google, Rex to OS.
Without this change:
[SPEW ] PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran
0 limit 0 flags f0000200 index 0
With this change:
[SPEW ] PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran
0 limit 0 flags f0000200 index 10
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iee2523876a8045e70effd5824afc327d1113038b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Enable x86 SHA accelerator for use by VBOOT library. This is useful when
CBFS verification verifies the hash of the file being loaded in x86.
BUG=b:227809919
TEST=Build and boot to OS in Skyrim. Observe a boot time improvement of
~10 ms with CBFS verification enabled.
Change-Id: I14efe7be66f28f348330580d2e5733e11603a023
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68954
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RTD3,_ON method sometimes can create delays during system boot.
Even when the power is already up, kernel still tries to call _ON
method to power up device, but it's unnecessary.
RTD3._STA returns device power, so _ON method can check _STA and see
if the power on process can be skipped
BUG=b:249931687
TEST=system can boot to OS with RTD3 pcie storage and save ~80 ms on
Crota. Suspend stress test passes 100 cycles
Change-Id: I296ce1b85417a5dbaca558511cd7fc51a3a38c84
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch implements a function to enable IOSF Primary Trunk Clock
Gating.
BUG=b:253210291
TEST=Able to build and boot rex to OS. Also needed for S0ix, tested
with Sandbox OS + Firmware combination for S0ix entry/exit.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I02e191336e99f97f4db58b27f4414001b642ad02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68430
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO debounce timebase bit 4 is only 183uS on Picasso. On the other
SoCs it is 244uS. This affects the 1mS and 2mS actual debounce times
slightly.
Time PCO Others
1mS 0.915mS 1.220mS
2mS 2.013mS 2.684mS
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Id84bef75e6ab134778721ca269d763a4bb2ddde5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69209
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to document 337348-001 (Intel® 300 Series and Intel® C240
Series Chipset Family Platform Controller Hub Datasheet - Volume 2
of 2), the only GPIOs that support PWROK reset are those in the GPD
group. The mappings themselves are correct, but they're assigned to
the wrong communities.
Change-Id: Ib586c987f768ddff31b053f4c108a8526326a7dc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69214
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
In function 'set_power_limits' there is a path to bail out early if the
Kconfig switch SOC_INTEL_DISABLE_POWER_LIMITS is selected. In this case
reading the MSR PLATFORM_INFO is useless and can be avoided. So read it
right before the value is needed.
This was found by the scanbuild.
In addition, fix an unnecessary line break to increase code readability.
Change-Id: Ibdededdfd56287fb9b9223e78033a3cd6425e1a2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
When using site-local we need to have ability to override
MAINBOARD_BLOBS_DIR with a different location (presumably somewhere in
site-local). site-local Makefiles.inc should be pulled in first
(different CL) allowing MAINBOARD_BLOBS_DIR to be overwritten.
Change-Id: I028042b947887d1182642ad4482dd1bba7ad8e23
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Use the common device ops instead of an soc-specific device ops.
TEST=builds for each soc
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I1804200c3c3f5ab492d237f4b03484c383862caf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add the generic data_fabric_acpi_name function and device ops to common
code.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I12053389a12081ddd81912a647bb532b31062093
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Make the data_fabric_acpi_name function more generic, in preparation to
move it to common.
TEST=build chausie, dump ACPI tables, and inspect DFD0 to DFD7
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I77140d8d0d6bf3e048b737de03d18142a6e23c1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Morgana/Glinda have a different register mapping for data fabric access,
although the registers themselves are mostly compatible. The register
layouts defined by each soc capture the differences and the common code
can use those.
Move the register offsets to soc headers and update the offsets for
morgana/glinda per morgana ppr #57396, rev 1.52 and glinda ppr #57254,
rev 1.51
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9e5e7c85f99a9afa873764ade9734831fb5cfe69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
