Support SPI flash dual read funciton which change spi mode (1-1-1)
to dual mode (1-1-2).
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: Iabd3668fc4bc42137b7743144fc1cced4fe72737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44852
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To minimize the quirks the kernel has to apply, the headset mic is set
to its correct value in coreboot.
Tested on lemp9, audio is functional.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I6b59de95f01360a5f7779f87f39edeb75dedc215
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43631
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSTACK2 (IOU3) should be stack number 4, mainboard uses stack number as
the index to access the bus number array read by get_stack_busnos().
Without the fix it would get the wrong bus number (0xb1).
Tested=On OCP Delta Lake, dmidecode -t 9 to verify slots bus number on
IOU3 are correct (0xb2).
Change-Id: I1c9e49bbc9a00de82d1fc67b3b4ed47e03eacdda
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:162232776
TEST=Measured the I2C bus frequency as 389 KHz, high time as 870 ns and
low time as 1580 ns.
Change-Id: I67d2725a7fc8d83e3fa8a56cfa86540c4e6f0971
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45084
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:163743035
TEST=Measured the I2C bus frequency as 384 KHz, high time as 924 ns and
low time as 1680 ns.
Change-Id: I60a5f6814fb9818c724f6b6fe465ea49d0de0f97
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45083
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP v3333 or later, provides a new UPD to Skip configuring
GPIO settings from FSP. coreboot should provide all the
required GPIO configuration for the platform when this UPD
is set.
BUG=b:166790597, b:146390704
BRANCH=none
TEST=build and boot volteer proto2
Cq-Depend:chromium-internal:3240396,chromium-internal:2870145
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: If32f35a188d510db8e4d8973cae78297d49a9240
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44913
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update FSP headers for Tiger Lake platform generated based FSP
version 3333. Previous version was 3313.
Changes Include:
1. Update comments
2. Add new UPD for Gpio Override support
BUG=b:166790597
BRANCH=none
TEST=build and boot volteer proto2
Cq-Depend:chromium-internal:3240396,chromium-internal:2870145
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie3f0688143eef532946c7a2141909c1ac173fc2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44912
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Rename from jasperlake to elkhartlake
2. Remove irelevant devices asls (ipu,ish,camera clock,gpio_op)
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I5e77081d1673cc0ca97edc63e9996c045ab6e9b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44812
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Replace "jsp" with "mcc"
4. Rename structure based on Jasperlake with Elkhartlake
5. Clean up upd override in fsp_params.c will be added later
6. Sort #include files alphabetically as per comment
7. Remove doc details from espi.c until it is ready
8. Remove pch_isclk & camera clocks related codes
9. Add new #define NMI_STS_CNT & NMI_EN as per comment
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I372b0bb5912e013445ed8df7c58d0a9ee9a7cf35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Unlike other platforms, Apollo and Gemini Lake have VmxEnable on FSP-S.
Note that this will enable VMX by default on both of these platforms.
Change-Id: I6a4470e0e64b10f07edfcf270bb02c7cd6a8fa1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This is an intermediate step to have SOC_INTEL_COMMON_BLOCK_CPU select
CPU_INTEL_COMMON directly, to avoid dependency problems.
Tested with BUILD_TIMELESS=1, UP Squared does not change.
Gemini Lake already selects this through SOC_INTEL_COMMON_BLOCK_SGX.
Change-Id: If737fa6d8700f435c8692c80244f0e71657c2236
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
The PRM does not describe the relevant bits, but Linux's i915 driver
handles these bits the same way for both Ironlake and Sandy Bridge.
Change-Id: Ice7412e335752bd7e297ad50f685effcefbd41d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All boards currently have backlight on either LVDS or eDP.
Change-Id: I878bc7f1ff75a2b82b9556e855aff1d4d03e0268
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Configure eldrid to use CSE Lite.
BUG=b:158140797
TEST=cd to volteer's asset_generation folder, execute
"./gen_all_variant_images.sh" and verify that all variant
images are produced.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I357abdac4102f358d3aa1cb50f600312039ef140
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The SMRR MSRs can be locked, so that a further write to them will cause
a #GP. This patch adds that functionality, but since the MSR is a
core-level register, it must only be done once per core; if the SoC has
hyperthreading enabled, then attempting to write the SMRR Lock bit on
the primary thread will cause a #GP when the secondary (sibling) thread
attempts to also write to this MSR.
BUG=b:164489598
TEST=Boot into OS, verify using `iotools rdmsr` that all threads have
the Lock bit set.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4ae7c7f703bdf090144637d071eb810617d9e309
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The IA32_MTRR_CAP register has a bit which indicates that the SMRR MSRs
can be "locked" and this patch adds the definition for that.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1254fb40c790f2a83dd11c2aabcf9bdf922b9395
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The IA32_SMRR_PHYS_MASK MSR contains a 'Lock' bit, which will cause the
core to generate a #GP if the SMRR_BASE or SMRR_MASK registers are
written to after the Lock bit is set; this is helpful with securing SMM.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I784d1d1abec0a0fe0ee267118d084ac594a51647
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For Volteer (and future Tiger Lake boards) we can enable mode S0i3.4
only if we know that the Cr50 is generating 100us interrupt pulses.
We have to do so, because the SoC is not guaranteed to detect pulses
shorter than 100us in S0i3.4 substate.
A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code
running in verstage, which will program a new Cr50 register, provided
that Cr50 firmware is new enough to support the register.
This CL adds code to detect the case when Cr50 is unable to generate
longer pulses, and in that case explicitly disable the S0i3.4 substate
as well as setting gpio_pm_override to all zeroes. This will increase
power usage slightly, but guarantee that the GPIO block in the SoC
does not switch to a slower sampling clock. In practice, this case
will only be encountered in the factory, before the Cr50 chip is
updated to a new RW image.
(Prior to this change, the gpio_pm_override was hardcoded to zero for
Volteer, but the S0i3.4 substate was not disabled. According to my
conversations with Intel engineers, that was not enough to guarantee
detection pulses shorter than 100us. But it is entirely possible that
we have just been "lucky" that the SoC has not gone into low power
mode during the boot process, where most of the cr50 communication
happens.)
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
BUG=b:154333137
Change-Id: Idef1fffd410a345678da4b3c8aea46ac74a01470
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add DTT (Dynamic Tuning Technology) support for Jasper Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=Noe
TEST=Build and boot on jslrvp board
Change-Id: I41409c70d8472c54ca452fc98d5ee9edf3ccd307
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the dooly variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.2).
BUG=b:155261464
BRANCH=puff
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_DOOLY
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Change-Id: I8e714cc9bf4a49266da77db88f8c4a3ca45878d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
3.6 schematic will separate TS power from eDP PP3300 to GPIO
for power control and correct GPIO assignment from GPIO_90 to
GPIO_32 instead.
BUG=b:161579679
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Ieef67e1d04201c5d9e1dc625c519e6d0307c55f0
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds support for line-buffered console output to System76 EC firmware.
Once the print command is received, the EC firmware multiplexes the output
to any enabled console on the EC. This can be a memory ringbuffer, a
parallel port (using the keyboard connector), or i2c (using the battery
connector). Once the entire buffer is sent, it sets the command register
to 0, indicating completion. For more information, please see:
https://github.com/system76/ec/blob/master/doc/debugging.md
Tested on system76/lemp9 with CONSOLE_SYSTEM76_EC enabled.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I861bf3e22f40dd6c3ec7ba1d73711b399358e332
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
On autogenerated FMAPs, there's no `UNIFIED_MRC_CACHE` region. The
current code will print a spurious error message about it, though.
Reduce the log level to BIOS_INFO to avoid confusion.
Change-Id: I0961bb2a7d2d81dc5c0d28f6e6c29b320421fc3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45076
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable SataPortsDevSlp for SATA ports 2 and 3.
Change-Id: Id6c69f4a6fe45cb5c6aad3f42c741a2724c6166c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Enable the I2C HID driver, configure I2C bus 0 and add the touchpad
device to the devicetree.
Tested on lemp9, touchpad confirmed to use i2c-hid driver in Linux
instead of PS/2.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ic3a90fda134b1d53f28ab687b3033ec52fee843b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43623
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
_GPE cannot be anywhere but at the root of the ACPI namespace.
This change ensures that is always the case.
Tested on lemp9, GPE still in correct location.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib31683b06e61da4b1859cd939c36879cebf4c03c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43630
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs required for DeepSx (e.g. SLP_SUS#) are not hooked up on the
lemp9. Therefore, drop the DeepSx settings.
Tested on lemp9, suspend works correctly.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Iab179abd7adc3a65dcfc43ce1b5742d514b711fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43629
Reviewed-by: Michael Niewöhner
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested on lemp9, SA thermal device appears in lspci.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I527e586b1dae5f8087d2364c63c9db5bcb643214
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Fsp configures the USB over-current pin and overrides the according pad
configuration to NF1, regardless of the port being configured as disabled.
Thus, set the OC pin to 0xff ("disabled") in this case to prevent this.
This allows us to skip setting USBx_PORT_EMPTY in the devicetree for
disabled USB ports.
Change-Id: Ib8ea2ea26c0623d4db910e487b37255e907b299d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45112
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Add required SoC programming till bootblock
2. Include only required headers into include/soc
3. Add CPU/PCH/SA EDS document number and chapter number
4. Include ADL-P related DID, BDF
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I204e692fabb84fce297bebee465f4ca624c6fe56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Don't configure USB3 port 4 since it's not used.
Change-Id: I6919f5ec3a5be53373f2ab75063764287b53baf5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner
Currently HECI3 gets enabled by the option Heci3Enabled, but this
duplicates the devicetree on/off options. Therefore depend on the
devicetree for enablement of the HECI3 controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Heci3Enabled setting, and divergent
devicetrees were adjusted.
Change-Id: Ic7d52096aee225c2ced1e1bc29ca850fe5073edc
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44579
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previous CL (1916f8969b) misinterpreted
spec as requiring size alignment on all IVHD device entries. The correct
requirement specifies only for 4-byte entries. The unneeded realignments
result in gaps in the table. The kernel hangs in early boot due to the
malformed table.
Remove 8-byte entry alignment.
BUG=b:166519072
TEST=Boot fully to morphius board with and without amd_iommu kernel
parameter. Confirm IVRS contains no alignment gaps/corruption.
Change-Id: Iddcff98279be1d910936b13391dd2448a3bb2d74
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
ddr_frequency is ambiguous and is interpreted differently in several
places. Instead of renaming this field, this deprecates it and adds
two new fields with unambiguous naming, max_speed_mts and
configured_speed_mts. smbios.c falls back to using ddr_frequency
when either of these fields are 0.
The same value was being used for both configured memory speed and
max memory speed in SMBIOS type 17, which is not accurate when
configured speed is not the max speed.
BUG=b:167218112
TEST=Boot ezkinil, no change to dmidecode -t17
Change-Id: Iaa75401f9fc33642dbdce6c69bd9b20f96d1cc25
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44549
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To allow using the 3 remaining Comet Lake SoCs, add a new Kconfig option
for each of them and configure the paths to FSP header files and FSP
binary.
Change-Id: I4272a6ee08e19769a8a17c93bb3ce2421be0bbc9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Michael Niewöhner
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GPP_F14 should be configured to be routed via APIC and not SCI.
BUG=b:162528549
TEST=verified on a volteer
Change-Id: Ie262ceeaea1c07bcc99e1545f5eb99e0d0dee905
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PSP bootloader and verstage are only used out of the RO region,
so don't build them into the RW sections.
BUG=None
TEST=Build & Boot
BRANCH=zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ic7bcb9a6a78926325e80755c010bb047e4a9485c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
This allows a platform to specify the location of the signing token
for the PSP verstage, and build it into the firmware image.
BUG=b:166108929
TEST=Build file into PSP firmware, verify that it's present and has
the correct ID.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I182ad9b48a2776ccd29ead0f54cfe14c5bf45560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
To use a signed PSP verstage, we're going to need to build it first,
then sign and store the binary. This patch allows the stored (signed)
verstage binary to be used.
BUG=b:166108929
TEST=Build with existing verstage binary instead of re-building it.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5cbceca3b75f05c5460190b1c829d1ffaab2c736
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Move PSP_SHAREDMEM_DRAM_END after _etransfer_buffer to ensure that the
transfer buffer actually lives within the 32KiB that is supported to be
transferred. Resulting symbol address change in bootblock.debug file
summarized below.
BEFORE:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02019000 T _epsp_sharedmem_dram
02019000 T _preram_cbmem_console
0201a600 T _epreram_cbmem_console
0201a600 T _timestamp
0201a800 T _etimestamp
0201a800 T _fmap_cache
0201ac52 T _efmap_cache
0201ac52 T _etransfer_buffer
AFTER:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02014040 T _preram_cbmem_console
02015640 T _epreram_cbmem_console
02015640 T _timestamp
02015840 T _etimestamp
02015840 T _fmap_cache
02015c92 T _efmap_cache
02015c92 T _etransfer_buffer
02019000 T _epsp_sharedmem_dram
BUG=b:167243965
BRANCH=None
TEST=checked 'cbmem -1' for FMAP error after ec reboot
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I9b482aced5deb40bd87d19d9c42585d8a6db5fc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45045
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Trogdor variants power their USB hub from a PMIC LDO that is
already enabled by QcLib, and some have a discrete LDO that is
controlled by GPIO_84. For the latter, let's make sure we assert that
GPIO on boot.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9d206cd7154ded3bf179e68c2b1421d0a8ee89f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
We're moving a lot of pins around on Trogdor again. For firmware this
only affects the RAM and SKU strapping ID pins. Since there are quite a
few of the old devices in circulation this time and some people seem to
care about mosys RAM information working, let's actually check the board
revision and support both cases this time.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7728d8ea4b7f6e7ff6721ade90f975f6efd5ddd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Set tcc offset to 5 degree celsius
2. Apply the DPTF parameters receive from the thermal team.
3. Change PL2 min value from 25W to 15W.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I68fdefe99cf36a39797c29ad84d08321bb8175f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This reverts commit 2ad859988b.
Reason for revert: broke the build
Change-Id: I7e7d917c2e8b698d5c7c3ce0b6d34e80696185f3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44993
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add new SPD file, "samsung_dimm_K4E8E324ED-EGCG.spd.hex".
2. Add SPD support in Rammus memory table, as follows:
SPD_SOURCES += samsung_dimm_K4E8E324ED-EGCG # 0b0110
SPD_SOURCES += samsung_dimm_K4E6E304ED-EGCG # 0b0111
BUG=b:166576463
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I82386507c4e996e0a59c26ce50de3bced45b1196
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44854
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BOOTBLOCK_CONSOLE is already set to yes in console/Kconfig file.
Change-Id: I2a4ee517795bc7b378afc5eae92e2799ad36111b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
1. Apply the DPTF parameters receive from the thermal team.
2. Change PL2 min value from 25W to 15W.
3. Change PL2 max value from 64W to 51W.
BUG=b:166696500
BRANCH=puff
TEST=build and verify by thermal team
Change-Id: I53a4e8809369883c3ba77744fdc05fb510408209
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44903
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
BUG=b:158986928
BRANCH=puff
TEST=duffy boots and dumped SSDT table for quick check.
Change-Id: I45987f44ec381917173f8d2a878edb50da454b4b
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO_144 is REPORT_EN pin for the touchscreen controller where 1 means
enable operation and 0 means stop operation. Override tree exposes
this pin as stop GPIO. Thus, it needs to be configured as active low
i.e. 0 = active (stop), 1 = inactive (enable report).
Change-Id: I349123655260349b78d2f75f846da0ce1dc966fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
4. Clean up upd override in fsp_params.c, will be added later
5. Temporarily remove _weak attributes in fsp_param & romstage.c
6. Add required headers into include/soc/ from jasperlake directory
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: If2bbe0b8a12bb78b3650f9d0a60f002f7eacb513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Clone entirely from Jasperlake
This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/36550
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
6. Add required headers into include/soc/ from JSL directory
Elkhart Lake specific changes will follow in subsequent patches.
1. soc/intel/elkhartlake: Update Kconfig
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I9f91c1efa81a358b1f59e032e209e07b62d54613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The BT instruction stores its result in CF and not ZF so use the
correct jump instruction.
This fixes a hang in postcar on CPUs lacking support for this
instruction. This concerns older pre-SSE2 hardware.
Change-Id: I704e3c579150fb9b9a292ef0e83050e7bf7cb078
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Checked with the schematics that all PCIe clocks have a corresponding
clock enable pin.
BUG=b:149970243
BRANCH=zork
Change-Id: If96cdf95e213682217e46a98fc69c5c2ef4a148d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44892
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
