Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver and set the pad's initial value to 0 since the signal is active-
high and shall be set by the IPMI/BMC driver.
Also add the pad to early gpio config, since it is expected to have an
external pull-up like X11SSM-F, which is wrong and would confuse the BMC.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Change-Id: If344b2271bfc8d50b8b64847109818f96f2abbcb
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver.
Also add the pad to early gpio config, since it has an external pull-up,
which is wrong and would confuse the BMC. Set the pad's initial value to
zero since the "POST complete" signal is active-high and shall be set by
the IPMI/BMC driver.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6409b2aca90585e44ee5d32df0ae73b259443f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set `bmc_jumper_gpio` to the JPB1 gpio to enable/disable BMC/IPMI
according to its value.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8581556d915cbad2c743a79db273479ba55798fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a new driver for OEM commands and select it from x11-lga1151-series.
The driver communicates the BIOS version and date to the BMC using OEM
commands. The command should be supported on all X11 series mainboards,
but might work with older BMC, too.
Tested on X11SSH-TF:
The BIOS version strings are updated on boot and are visible in the
BMC web UI.
Change-Id: I51c22f83383affb70abb0efbcdc33ea925b5ff9f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
There is a whole bunch of pads being configured by the vendor firmware
that are either unconnected due to unpopulated resistor pads, only
connected to test points for vendor debugging purposes or just used as
strap. Configure them as NC with an appropriate pull to disable the
RX/TX functions.
The pads have been determined by dissecting a dead board.
This patch has been tested thoughroughly on a machine, normally used
productive, to see if any issues arise. No problems occurred at all.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I06b942e3182469f87e41914c893e5b485ccca420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Follow vendor and enable Advanced Error Reporting for PCIe root ports.
This enabled the Linux AER driver, which handles PCIe error conditions.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9d9b5afca0ca891e2812445db1d42a46ba16199e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48369
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the subsystem ids to PCI ports and devices, which were dumped on
vendor firmware using `lspci`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Idb36c5c72e1b0b8303439ae5dce772822f551d2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow vendor and enable LTR on all root ports to optimize for devices'
latency requirements and also optimize power management while preventing
failure due to wrongly guessing idle states, which happens without LTR.
Tested successfully. No errors show up in dmesg.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8f72087c71e291d2412dc7b3e16ee7f419e2ca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48367
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All X11 boards currently supported have Intel SPS without support for
S3/S5. Thus, drop it from Kconfig.
Note: not all X11 boards are server boards. When a X11 desktop or
workstation board should be added, this can be selected by the boards,
where S3/S5 work.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ie75c9217078d38c42eba2b30c078b8bb1c2ca694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Correct unconnected pads that are configured different currently by
copying vendor configuration while porting the board.
Add internal pull resistors to all unconnected pads, that do not have an
external pull resistor, to prevent floating.
The pads have been determined by dissecting a dead board. This commit
only changes pads, that are not connected at all and don't have any via,
so we can be absolutely sure there is no other connection.
Change-Id: I991fe270b42f430f7447712236e0f80b3d5bba2a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
(Re)configure various pads found by dissecting a dead board and vendor
firmware, as well as the BMC firmware:
- GPP_B14: input connected to jumper JBR1 - could be used to implement
"BIOS Recovery" ("Top-Block Swap") functionality; external pull-up
- GPP_C20: output to BMC alert CPU_THROTTLED# - can be used to notify
the BMC about a thermal throttling event. Not implemented in vendor
firmware.
- GPP_C23: input connected to the CPU's CATERR# output; external pull-up
Not actively used by vendor firmware.
- GPP_D1: output connected to on-board and front panel power LEDs
- GPP_D18: output connected to PERST# of both CPU PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D19: output connected to PERST# of both PCH PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D22: input connected to the BMC enable/disable jumper JPB1; Will
be used later in CB:48096 and CB:48097; external pull-up
- GPP_G0 - GPP_G3: dedicated/integrated CPU switching; probably not
useful, since the IGD is not connected to any ports on this board.
External pulls ensure correct function of a dGPU even without driving
the gpios. Not used by vendor firmware.
- GPP_G12 - GPP_G16: inputs for binary SKU_ID; external pulls
- GPP_G20: PWRFAIL# input from JPI2C1 (pin 3); external pull-up; Not
used by vendor firmware.
Also add comments for documentation. While at it, mark ME-owned pads as
reserved.
Change-Id: I9f9328e9ce6f7e291b171f776bb98bc617b64b93
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Skylake FSP isn't used by coreboot anymore. Therefore, drop the
misleading comment and the "KBLFSP" extension from the names of these
enums.
Also, drop the "MODE" extension to make their names shorter in general,
since it doesn't add any more value.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: If37d40e4e1dfd11e9315039acde7cafee0ac60f0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48377
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All four SMI/NMI interrupt inputs have an external pull-up resistor and
get triggered by pulling the line low. Thus, correct the trigger to
active-low.
Also document the signals by adding appropriate comments.
The pads' connections have been determined by dissecting a dead board.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Id1a8c1e0b9fe723a15d04a88d565a53eeba9b085
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48093
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop the NMI overrides, since NMI now gets configured in gpio common
code. Also remove the variant init mechanism, which is unused now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I02e0c679f9aafe33108320a8dfc62dcb278202ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48092
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently
supported X11 boards are server boards.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rework gpio setup for the board series to not use headers but
stage-specific compilation units.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Drop the TODO comment, since there is no TODO left. Also drop the now
obsolete TODO section from the board documentation.
Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Time has shown that using spaces never converges into proper alignment.
Change-Id: I5338aeaf139580f9eab3e1e02cb910080a95d2c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
They default to zero already, so we might as well drop them.
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change.
Change-Id: I3c04240b270f51d584f879e1344301679f133fdb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Add interrupts for all enabled superio devices to quiet the warning
about missing interrupts in devicetree.
Vendor uses interrupt 0x00 for all devices except SUART* and KBC, so
let's do that, too. This also changes SWC from 0x0b to 0x00.
Verified with superiotool on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I7a6dc7345f020e53415a7d0d104ce93ab4b194fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonas Löffelholz
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- remove comments (except the GPIO group), because it does not contain
useful information that helps to understand the circuit, which we do
not have;
- remove empty lines between macros;
- use a shorter PAD_CFG_GPI_INT() macro instead of
PAD_CFG_GPI_TRIG_OWN() to set DRIVER mode.
Change-Id: Ia7111341aab6f400da70d936849e4d4c9406905b
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Converts bit field macros to target PAD_CFG_*() macros, which were
hidden in the comments. To do this, the following command was used:
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F,
remains identical.
Change-Id: Idad7536854d4b1ae7dcf7934e81de438478fe059
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35679
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fixes some bit fields to convert to target macros PAD_CFG_*() macros.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: I291f5f0f34505c466b610aa4049c8cc35937d140
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42918
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch excludes bit fields that should be ignored [1] in order
to convert current macros to target PAD_CFG_*() macros. The following
commands were used for this:
./intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
/intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/
supermicro/x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
[1] ignore RX Level/Edge Configuration (bit 26:25) and RX/TX Buffer
Disable (bit 9:8) for the native function, because it does not
affect the pad in this mode.
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Change-Id: Icdf366a8d416598cec5afcb9a0fae6bf7ecd7ba0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42917
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the intelp2m utility [1,2] with -fld=cb options to convert the pad
configuration format with the raw values of the DW0 and DW1 registers
to the format with the bit fields macros: PAD_FUNC(), PAD_RESET(),
PAD_TRIG(), PAD_BUF(), PAD_PULL(), etc... Also use the -ii options to
generate the target macro in the comments, so that it is easier to
understand what result we should get:
./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h
./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/
x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h
[1] https://github.com/maxpoliak/pch-pads-parser
[2] https://review.coreboot.org/c/coreboot/+/35643
This is part of the patch set
"mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m":
CB:42916 - 1/4 Decode raw register values
CB:42917 - 2/4 Exclude fields for PAD_CFG
CB:42918 - 3/4 Fixes some field macro
CB:35679 - 4/4 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F,
remains identical.
Change-Id: I209ecdca75a0e62233d3726942c75ea06acc40a2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42916
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
