This is spotted using "./util/lint/kconfig_lint"
While at it, do the check in C and not the preprocessor.
Change-Id: Icfda267936a23d9d14832116d67571f42f685906
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently without any trigger the wakeup event is generated on both the
rising and falling edges of the GPIO input. Add support to specify the
trigger explicitly so that the configuration can be passed to the
kernel.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder and ejected from its holder.
Change-Id: Ifb08ba01106031aa2655c1ae2faab284926f1ceb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Added new routine cr50_i2c_probe() which ensures that communication
with the Cr50 over I2C is good prior to attempting other initialization
of the Cr50 and TPM state. This avoids a race condition when the Cr50
is first booting that it may reset it's I2C slave interface during the
first few I2C transactions initiated from coreboot.
BUG=b:120009037
BRANCH=none
TEST=Run the Cr50 factory update against Careena board. Confirm that
I2C reads are retried until the DID VID is valid. Tested against debug
Cr50 firmware that forced failure of cr50_i2c_probe() and verfied that
coreboot shows recovery screen.
Change-Id: I47c59a32378ad00336277e111e81ba8d2d63e69a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Add API that should be implemented by the boot media drivers
for write-protecting a subregion.
Change-Id: I4c9376e2c2c7a4852f13c65824c6cd64a1c6ac0a
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/28724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some SPI controllers support both READ and WRITE protection
add a variable to the protect API for the callers to specify
the kind of protection they want (Read/Write/Both).
Also, update the callers and protect API implementation.
BUG=None
BRANCH=None
TEST=test that the mrc cache is protected as expected on soraka.
Also tried if the read protection is applied correctly.
Change-Id: I093884c4768b08a378f21242ac82e430ac013d15
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/30559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I4d15d5acf0e2044e5128ce809c282fbcb35f24f0
Reviewed-on: https://review.coreboot.org/c/30746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Passes out wakeup-delay to driver. This delay is applied at
the start of capture to make sure dmics are ready before we
start recording. This avoids pop noise at begining of capture.
BUG=b:119926436
TEST=
With kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
No pop sound heard at start of capture
Change-Id: I32b18bf80fad5899ab4093a127dfd52d589bc365
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Default to FSP binary and headers shiped in 3rdparty/fsp.
* Drop headers and code from vendorcode/intel/fsp1_0/broadwell_de
* Select HAVE_FSP_BIN to build test the platform
* Fetch FSP repo as submodule
* Make FSP_HEADER_PATH known from FSP2.0 useable on FSP1.0
* Introduce FSP_SRC_PATH for FSP source file
* Add sane defaults for FSP_FILE
Tested on wedge100s.
Change-Id: I46f201218d19cf34c43a04f57458f474d8c3340d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
It was only hooked up for galileo board when using the obsolete
FSP1.1. I don't see how it can be useful...
Change-Id: Ifd7cbd664cfa3b729a11c885134fd9b5de62a96c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30691
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Read back the stack guards after most of the romstage took place.
Change-Id: Ia7dc26c7ed1750d4ebbe7514ed87da57f9e34a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add S25FL208K (ID 0x4014), S25FL132K (ID 0x4016) and S25FL164K (ID 0x4017)
chips in a way similar to S25FL116K (ID 0x4015) chip from the same family.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I9bf7197bbc0d12797c8ed100c673628de9c140f7
Reviewed-on: https://review.coreboot.org/c/30874
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Superseeded with DEBUG_CONSOLE_INIT.
For dbgp_print_data() return early and skip reading
registers when dprintk() would not get printed anyways.
Change-Id: Idf470b8572ad992c8d4684a860412d9140f514ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds a workaround for ThP2. The PCIe root port LCTL2.TLS
is by default GEN1 and ThP has bad synchronization on polarity
inversion. When the root port request for speed change, ThP doesn’t
confirm the request, and both sides are moving to polling after
timeout, hot reset is issued, and then most of the CFG space is
initialized. From the observation, CCC/ECPM/LTR would be reset to
default but CCC/ECPM of root port and end devices have been
reconfigured in pci_scan. The LTR configuration for root port
is still missing.
BUG=B:117618636
BRANCH=None
TEST=Warm/cold reset for 10 times and didn't see unsupported request
related AER error messages & $lspci -vvs 00:1c.0|grep LTR and
ensure LTR+ is presenti & $iotools pci_read32 0 0x1c 0 0x68
and ensure bit10 is set.
Change-Id: Id5d2814488fbc9db927edb2ead972b73ebc336ce
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This allows to check if stack overflows the car globals.
Change-Id: I369b2d846f35914facb3e69cc762f7e555271bec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Required for ACPI S3 suspend support at some motherboards,
e.g. EN25QH32 chip entry for AMD Lenovo G505S laptop.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I8343a1741be5ea294de0773962c021428815934c
Reviewed-on: https://review.coreboot.org/c/30744
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Have same usage of registers with romcc bootblock
and C_ENVIRONMENT_BOOTBLOCK.
Change-Id: Ibfa80e40f0b736a904abf4245fc23efc0cdc458d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
If requested EHCI function is not on bus 0, we would
need to open MMIO windows and configuration register
space for the connected upstream PCI bridge for it
to work. We don't plan to do so.
Change-Id: I7c1c60f9d9890dedfedc9d977faf5152ba362692
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The first stage attempting to initialise usbdebug
gadget will leave it marked as non-present if none
is detected. This allows further stages to bypass
usbdebug init sequence.
Change-Id: I1491d7fab3c89f210fb03b32481f697bc7a1d1e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The EHCI hardware needs to be initialized only once during CAR stages.
Some exception need to be made when a blob messes with the EHCI
hardware. To achieve this add a fixed location in the car.ld linker
script such that the ehci debug information can be shared across CAR
stages.
Currently this means only romstage and bootblock, but verstage can
also be hooked up later on.
Tested on google/peppy: Both the bootblock and the romstage properly
output console.
Change-Id: I78e20a172fd5cc81f366d580f3cce57b9545d7a2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently this needlessly initializes the hardware in the both the
romstage and the bootblock, but it works.
Build option is renamed to USBDEBUG_IN_PRE_RAM to reflect the
use better, related support files can be built to pre-ram stages
regardless of usbdebug being enabled or not.
Tested on Google/peppy (adapted to C_ENVIRONMENT_BOOTBLOCK).
Change-Id: Ib77f2fc7f3d8fa524405601bae15cce9f76ffc6f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Expose the function that can unconditionally re-initialise
EHCI debug host and gadget.
Given the missing header in soc/intel files that prevented
building with USBDEBUG_IN_ROMSTAGE=y, it is not actually
known if those SOCs work at all for usbdebug.
Change-Id: I8ae7e144a89a8f7e5f9d307ba4e73d4f96401a79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch is from Linux, commit 3856081eede2. The commit message there
is:
> commit 3856081eede297b617560b85e948cfb00bb395ec
> Author: Y.C. Chen <yc_chen@aspeedtech.com>
> Date: Thu Feb 23 15:52:33 2017 +0800
>
> drm/ast: Fix AST2400 POST failure without BMC FW or VBIOS
>
> The current POST code for the AST2300/2400 family doesn't work properly
> if the chip hasn't been initialized previously by either the BMC own FW
> or the VBIOS. This fixes it.
>
> Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
> Tested-by: Y.C. Chen <yc_chen@aspeedtech.com>
> Acked-by: Joel Stanley <joel@jms.id.au>
> Cc: <stable@vger.kernel.org>
> Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested on a Supermicro X10SLM+-F with an AST 2400 where the BMC flash
chip has been completely erased. Before the patch, the display resembled
a rainbow. After the patch, the display works well.
Original-Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Original-Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Original-Tested-by: Y.C. Chen <yc_chen@aspeedtech.com>
Original-Signed-off-by: Dave Airlie <airlied@redhat.com>
Change-Id: I72efcf907fbd1263fe21d4f36fe900b305419c44
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This adds a convenient helper function to add vbt binaries to cbfs.
Change-Id: I80d9b3421f6e539879ad4802119fe81d7ea1e234
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30430
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Any board that uses the AST driver will have support for native graphics
init. So, select the option in the driver instead of every board.
Change-Id: I2bf42c168d1ffdda11857854889b74953abd7e40
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Updates to current master.
This includes:
- A fix for textmode scaling on G45
- Refactor things to rely less on inline proving
- Increased width of modeline fields to 32 bits
Change-Id: Iab2915b747f6e4fa4e78eb28fea29bb3a9b3b687
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30311
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add mechanism to configure GPE wake event which in turn can be used as ACPI
Power Resources for Wake
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the wake GPE event is added to ACPI Power Resource for
Wake.
Change-Id: Iacc12b8636aaac98a8689a211cbe1dcfe306f342
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add an entry to the soc_clock table for a 216MHz clock so that
the I2C controller clock is calculated correctly when the I2C
bus is used in coreboot.
This was tested by measuring the I2C clock speed on H1 I2C bus
on a sarien board in coreboot and ensuring it is ~400KHz.
Change-Id: I6c3cacdad318a5ce41bc41e3ac81385c2d4f396c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use a raw fmap region SMMSTORE for the SMMSTORE mechanism, while
keeping the initial option to use a cbfsfile.
TESTED on Asus P5QC, (although it looks like the tianocore patches
using it might need some love as they can't seem to save properly).
Change-Id: I8c2b9b3a0ed16b2d37e6a97e33c671fb54df8de0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The Linux kernel can use the ACPI _PLD group information to
determine peer ports. Currently to define the group information
the devicetree must provide a complete _PLD structure. This
change pulls the group information into a separate structure that
can be defined in devicetree. This makes it easier to set for
USB devices in devicetree that do not need a full custom PLD.
This was tested on a sarien board with the USB devices defined
by verifying that the USB 2/3 ports are correctly identified
with their peer in sysfs.
Change-Id: Ifd4cadf0f6c901eb3832ad4e1395904f99c2f5a0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The TB has to be inverted to actually protected the correct region.
Tested on elgon using I67eb4ee8e0ad297a8d1984d55102146688c291fc.
Change-Id: I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Backlight control of internal panels likely won't work as configuration
for that seems absent in coreboot. Also, libgfxinit doesn't support any
MIPI/DSI connections, yet, and neither Gemini Lake.
TEST=Booted work-in-progress port kontron/mal10 with VGA text and
linear framebuffer modes. DP display came up.
Change-Id: I7b111f1cdac4d18f2fc3089f57aebf3ad1739e5d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for updating microcodes on FSP 1.0 platforms
before memory is initialized. This is a requirement to
fill other FIT entries except for microcode updates.
Change-Id: Ie31acaf0fc41c51b9edf65b981d43d7732661770
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29819
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Huang Jin <huang.jin@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Missing hob 7.3 FSP_NON_VOLATILE_STORAGE_HOB is reported always.
This hob is only generated by FSP during non-S3 and MRC data is changed.
Now display missing FSP_NON_VOLATILE_STORAGE_HOB only when this hob is
required.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: Ice8220149c2e44bb2da010d5a7d8bc4dbeca11e0
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Huang Jin <huang.jin@intel.com>
It's not implemented for Skylake, all combinations that try to enable it
either result in Kconfig or linker errors.
Move `config SKIP_FSP_CAR` into drivers/intel/fsp1_1 where it's
effective.
TEST=Built Intel/Kunimitsu (FSP1.1) and Intel/KBLRVP8 (FSP2.0) default
configs with and without this patch: binaries stay the same.
Change-Id: Iae0a2d2c7fd7a71ed24118564e6080c4789cda28
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Initially, I wanted to move only the Kconfig DISPLAY_MTRRS into the
"Debug" menu. It turned out, though, that the code looks rather generic.
No need to hide it in soc/intel/.
To not bloat src/Kconfig up any further, start a new `Kconfig.debug`
hierarchy just for debug options.
If somebody wants to review the code if it's 100% generic, we could
even get rid of HAVE_DISPLAY_MTRRS.
Change-Id: Ibd0a64121bd6e4ab5d7fd835f3ac25d3f5011f24
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29684
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
soc/car_setup.S is included when SKIP_FSP_CAR is enabled,
but no chipset/SoC have car_setup.S available.
Remove include and post_code() call always solving build errors.
BUG=NA
TEST=NA
Change-Id: Iebae2940eb10c9ca9054437be4740c79137bcc61
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Huang Jin <huang.jin@intel.com>
CONFIG_FSP_USES_UPD is not used by FSP 1.1.
Remove this config from this file.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: If922b6cb2d39b10f6657b4d80e54b226d1386c76
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Huang Jin <huang.jin@intel.com>
Returned status code FspTempRamInit() is not displayed when error occurs.
Move the printk() call before the check for status.
BUG=NA
TEST=Portwell PQ7-M107
Change-Id: Id87e5c765d09f4ab199db9eba07a949b031a709a
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29695
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Huang Jin <huang.jin@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ability to define a reset gpio in acpi for a USB device.
BUG=b:119275094
Change-Id: Ife3ea43a1eadf2548aa52b8fbd792e691d7cc7f2
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
The dependencies of CONSOLE_SERIAL and DRIVERS_UART were somehow
backwards. Fix that. Now, CONSOLE_SERIAL depends on DRIVERS_UART,
because it's using its interface. The individual UART drivers
select DRIVERS_UART, because they implement the interface and
depend on the common UART code.
Some guards had to be fixed (using CONSOLE_SERIAL now instead of
DRIVERS_UART). Some other guards that were only about compilation
of units were removed. We want to build test as much as possible,
right?
Change-Id: I0ea73a8909f07202b23c88db93df74cf9dc8abf9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
It defaults to y to avoid having to select it per mainboard. But that
makes a mess because it results in linker conflicts unless other UART
drivers disable it explicitly.
We try to be smarter about the default value for now. The real solu-
tion would be to hardcode it per mainboard. But who knows which boards
actually have it?
Change-Id: I7e755fe0e4f6d1c31ef2854603a5510c3cdc4967
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29571
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a helper function specific to ramstage to add the boot count
information into event log at ramstage.
BUG=b:117884485
BRANCH=None
TEST=Add an event log from romstage, boot to ChromeOS
Change-Id: Ic79f1a702548d8a2cd5c13175a9b2d718527953f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29542
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Group event log state information together to manage them better during
different stages of coreboot.
BUG=b:117884485
BRANCH=None
TEST=Add an event log from romstage, boot to ChromeOS
Change-Id: I62792c0f5063c89ad11b512f1777c7ab8a2c13e5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now postcar is a standalone stage, add
it as target to all TPM bus drivers.
This is a required for a measured boot.
Change-Id: I758185daf3941a29883c2256b900360e112275e1
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/29546
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case the function pointer isn't set return an error.
Change-Id: I9de300f651ac93889dafa7377c876bf5ae2c50cc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/29531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
port is allocated in ACPI, without checking for value.
Don't use port value when zero.
BUG=N/A
TEST=Portwell PQ-M107
Change-Id: Ia44281b82d003b29bffbf985b774ddd661b65c4e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/29331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Make use of the common CF9 reset in SOC_INTEL_COMMON_RESET. Also
implement board_reset() as a "full reset" (aka. cold reset) as that
is what was used here for hard_reset().
Drop soc_reset_prepare() thereby, as it was only used for APL. Also,
move the global-reset logic.
We leave some comments to remind us that a system_reset() should
be enough, where a full_reset() is called now (to retain current
behaviour) and looks suspicious.
Note, as no global_reset() is implemented for Denverton-NS, we halt
there now instead of issuing a non-global reset. This seems safer;
a non-global reset might result in a reset loop.
Change-Id: I5e7025c3c9ea6ded18e72037412b60a1df31bd53
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change replaces use of post codes 0x34 and 0x36 in fsp drivers to
instead use POST_MEM_PREINIT_PREP_{START,END} to make it easy to
search from where these post codes are generated during boot flow.
Additionally, it adds POST_MEM_PREINIT_PREP_END to fsp2_0 memory_init
to make it consistent with fsp1_1 memory init.
Change-Id: I307ada1679f212c424e9f7ad2c9d254e24f41fd3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CPU_MICROCODE_CBFS_LEN and CPU_MICROCODE_CBFS_LOC configs pass the CPU
microcode length and base address in CBFS to FSPT binary as init parameters.
Add new config FSP_T_XIP in Kconfig, which is selected by platform config.
If FSP_T_XIP is selected, then relocate FSPT binary while adding it in CBFS
so that it can be executed in place.
BUG= None
TEST= Build for both CFL RVP11 & RVP8 and verified for successfull CAR setup.
Change-Id: Ic46e0bb9ee13c38ff322979119c4813653c61029
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
A shortcoming of this driver is that if multiple devices with the same PCI ID
are present and don't have an eeprom, they would all get the same macadress set.
The r8168 driver deals with such cases so it should be easy to implement if
needed.
Change-Id: I5c32df00e25453c350a45e7f1ee6834b89c4289f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
With https://github.com/IntelFsp/FSP/pull/4 merged, this allows using
Intel's FSP repo (that we mirror) to build a complete BIOS ifd region
with a simple coreboot build, automatically drawing in headers and
binaries.
This commit covers Apollolake, Coffeelake, Skylake, and Kabylake.
Skylake is using Kabylake's FSP since its own is FSP 1.1 and Kabylake's
also supports Skylake.
Another candidate (given 3rdparty/fsp's content) is Denverton NS, but
it requires changes to coreboot's FSP bindings to become compatible.
Cannonlake, Whiskeylake require an FSP release.
Change-Id: I8d838ca6555348ce877f54e95907e9fdf6b9f2e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28593
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It exposes an interface that is as generic as possible, so payloads
and/or kernels can use it for their data.
Change-Id: I9553922f9dfa60b9d4b3576973ad4b84d3fe2fb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/25182
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support in generic device driver to add properties to
DSD table. This driver can be used by all generic devices that do not
need any special handling other than simply adding device properties
to be used by OS.
BUG=b:112888584
Change-Id: I0ca6614f1ef322397618676bbf6da898bef18990
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The W25Q128J is a QSPI flash chip, without ~HOLD and ~WP.
Add the device id to make coreboot boot from it.
Change-Id: I623fdf7d7e30eb28259bec6294785ad873f1f503
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Extend the generic flash interface to probe for write protected regions.
Add Winbond custom code to return flash protection.
Tested on Cavium EVB CN81xx using W25Q128.
Change-Id: I933a8abdc28174ec32acf323c102d606b58c1ea5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25082
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make XBCM `Serialized` (obvious), and check for the callee clearing the
request bit (we checked only the status for 0 which we potentially wrote
ourselves).
Change-Id: Ic92d525eda8d0a159fa5ddaacf230658d71c1578
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The device tree now supports 'hidden' and the status can be found in
`struct device.hidden`. A new acpi_device_status() will return the
expected setting of STA from a `struct device`.
BUG=b:72200466
BRANCH=eve
TEST=Builds and boots properly on device eve
Change-Id: I6dc62aff63cc3cb950739398a4dcac21836c9766
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28567
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBLV is not kept up to date by Linux' i915. We should fix that too,
but it will likely take some years until we can always expect it to
work.
For now read the register values directly. To accomodate that we
are not the only one writing those, revise XBQC() to search for
the closest value in BRIG (instead of a lower equal one) and round
more accurately for better matches.
Change-Id: I4e2d8fa34e75463d4cf7242af3e2c67577cfa2a5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The SiFive UART on the HiFive Unleashed uses the tlclk as input clock
which runs at coreclk / 2.
The input frequency is configured in the board code depending on the
current stage. (bootblock + romstage run at 33.33Mhz, ramstage at 1Ghz)
Change-Id: Iaf66723dba3d308f809fde5b05dfc3e43f43bd42
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/27440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Add a __noreturn macro that wraps __attribute__((noreturn)) and replace
current users with the macro.
Change-Id: Iddd0728cf79678c3d1c1f7e7946c27375a644a7d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/28505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
VPD reference: https://chromium.googlesource.com/chromiumos/platform/vpd/+/master/README.md
Copy ChromeOS VPD driver to add support for VPD without CROMEOS.
Possible use case:
* Storing calibration data
* Storing MAC address
* Storing serial
* Storing boot options
+ Now it's possible to define the VPD space by choosing
one of the following enums: VPD_ANY, VPD_RW, VPD_RO.
+ CHROMEOS selects now VPD as part of it.
+ VPD is implemented as driver.
Change-Id: Id9263bd39bf25d024e93daa57053fefcb1adc53a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25046
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP 2.1 implementation is adding features on top of fsp2_0.
One such feature is a shared stack implementation that requires
coreboot to allocate stack for fspm and then fsp uses the same
stack as coreboot. This implementation adds support for shared
stack feature.
Change-Id: I6581111dbaddfa403eca14100577ccc8a05c4ec7
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/28358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add CMOS option that allows to use both integrated and discrete GPU.
Tested on ThinkPad W530.
Change-Id: I8842fef0fa1235eb91abf6b7e655ed4d8598adc7
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We should always update BCLP, no matter if the driver is ready yet to
process the request. This way it will hold the current value when the
driver initializes.
Change-Id: I4b091d744f95da39abe542966f0a8589a187573b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The _BCM function requires a percentage value. While the
brightness in mailbox3 requires a value in uint8_t. Meaning 255 = 100%.
Previous implementation stored the percentage brightness value resulting
in limiting the brightness to ~40% of it's maximum power.
Only affects brightness control using mailbox3.
Fixes: 6838aaebf9 ("drvs/intel/gma/acpi: Add methods to use MBOX3")
Change-Id: I290b5f5b2a8ee406e39e86d3e0de9997798d890d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/28345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change makes WIFI_SAR_CBFS user selectable option so that it can
be enabled/disabled from menuconfig along with the SAR filepath.
BUG=b:112425861
Change-Id: Idf6feaefe68e7ebf6786c2c36e92a054fba4483c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This reverts commit c5ee35ff86.
Reason for revert: breaks boards, uncertain if it _really_ works.
Change-Id: I9ba2ba877b9a391306f89295c0c1d0e2d011c5ea
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28338
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jean Lucas <jean@4ray.co>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This open-codes flash_cmd, but until the API is fixed for real, it uses
xfer's existing scatter-gather ability to write command and data in one
go.
BUG=chromium:446201
TEST=emerge-coral coreboot succeeds
Change-Id: Ic81b7c9f7e0f2647e59b81d61abd68d36051e578
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For debug reasons, sometimes you not only want to log an event, but also
some extra information that would help debugging. Create an extended event
reporting event type with a dword complement, and define extended events
for failing to enter S3 due to pending wake event (one for pm1 and one for
gpe0).
BUG=b:111100312
TEST=Add a fake pending wake event, build and boot grunt, see the event in
eventlog.txt.
Change-Id: I3e8df0953db09197d6d8145b0fc1e583379deaa5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
* Fix ACPI resume path compilation for TPM ramstage
driver
* Move enabling of the TPM prior activation and remove
reboot return status from TPM enable.
More information can be found via the TCG
specification v1.2
Tested=Elgon
Change-Id: Ided110e0c1889b302e29acac6d8d2341f97eb10b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28085
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Callers should have a default ready and get noticed by the return
value of get_option(). No need to scare log readers at this location.
Change-Id: Ied373d8a02afdc8d1017c9f41d9004e3797dfbb3
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28215
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The help text is already very clear but some users (first and
foremost the author of this patch ;) are still selecting
USBDEBUG_DONGLE_BEAGLEBONE when using a BeagleBone Black and
waste hours on analyzing the debug output of EHCI debug driver.
Change-Id: Ibf002db7d81ed44878f3ce0324170e4b99e780a5
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Under some conditions, cr50_i2c_read() can return without actually reading
the TPM, which will leave access uninitialized. Set an initial value for
access, and if TPM fails to respond in time check if at least TPM was read.
This way avoids printing an uninitialized value.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I5ec7a99396db32971dc8485b77158d735ab1d788
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Unfortunately stmicro.c does not distinguish the 1.8V version from
the 3.3V versions (yet) although they have distinct RDIDs.
I have at least ordered the ID macros accordingly and used a proper name
in this patch.
Change-Id: Id4fd8d46dcc9e51c1ae5504a32c2f8c5cfd863a1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/27861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change gets rid of unused wrdd.asl in intel wifi driver. This
file became redundant when all boards moved to using SSDT for wifi
device.
Change-Id: I8b5b3816d77c90e75052c58a3120ab62185873a7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27963
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SLB9665 are not initialized correctly. It looks like SLB9665 and SLB9660
return the same DEV ID. Initialize these devices according to TPM Kconfig
selections.
Tested on apu2 with following change:
https://review.coreboot.org/#/c/coreboot/+/28000/
Change-Id: Ic20b9a65ef6a4ee392a9352f7c9bf01b2496f482
Signed-off-by: Kamil Wcislo <kamil.wcislo@3mdeb.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/21983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Careena EVT SanDisk EMMC sku has high fail rate of 0x5B reboot failure.
It'll need to increase 1.8V EMMC CLK/CMD, Data driving strength for
this issue.
CLK[6:4]
CMD,DATA[3:1]
original register value: 0x6B
enhanced: 0x7F
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I3db38ff12c566c258895c6643008a0472ca528bb
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27816
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In procedure spi_flash_cmd_erase(), parameter "len" is not validated and
could lead to the return of an invalid (non-initialized) value. Validate
the parameter early on.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I0b5129a15c9e0ea45f4dba4ab0729196cb64699b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Use bitfields to pack the struct more tightly.
Change-Id: If1e7a5a3a9504327f987403ec0a7b79b2383792a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27815
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add Mailbox 3 driver
* Request brightness change through Mailbox 3
* Return Ones on error or if unsupported
* Mark existing code as legacy
(still required if no GMA driver is running)
* Call legacy code if Mailbox 3 is unsupported, on error or
if gma driver isn't running
Tested on Lenovo T430:
* Brightness control still works
* Brightness is the same on S3 resume
Change-Id: I51554c819148336b204d28972cbf775a10c3fb8a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Make tcpa_log_init static and move init code into
the tcpa_log_add_table_entry routine.
* Add more checks for log initialization.
* Fix minor issues
Change-Id: I215d79eed7ad17c6ab87f0c4b14a282e519ef07d
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/27769
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These two da7219_aad properties are optional:
- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
[<2800>, <2900>]
- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
When the Mic Bias Higher Voltage feature is not required, firmware should
just not provide the dlg,micbias-pulse-lvl and dlg,micbias-pulse-time
properties.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:111700809
TEST=On grunt:
No "Invalid micbias pulse level" in dmesg
Change-Id: Ie99a8962e78c68b3f6927d0de34168f265d4efa9
Reviewed-on: https://review.coreboot.org/27613
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Akshu Agrawal <akshu.agrawal@amd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Logic: If vboot is not used and the tpm is not initialized in the
romstage makes use of the ramstage driver to initialize the TPM
globally without having setup calls in lower SoC level implementations.
* Add TPM driver in ramstage chip init which calls the tpm_setup
function.
* Purge all occurrences of TPM init code and headers.
* Only compile TIS drivers into ramstage except for vboot usage.
* Remove Google Urara/Rotor TPM support because of missing i2c driver
in ramstage.
Change-Id: I7536c9734732aeaa85ccc7916c12eecb9ca26b2e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24905
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Devices using NORTHBRIDGE_INTEL_NEHALEM have an ironlake IGD which does not
support eDP, therefore default to LVDS.
Change-Id: I669c7793a6f78d72899df21b74b9314ef39a29af
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27512
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Move vboot/tpm specific implementation to vboot.
* Only call functions if CONFIG_FSP2_0_USES_TPM_MRC_HASH is set.
* Preparation for software hash function support, no logic changed.
Change-Id: I41a458186c7981adaf3fea8974adec2ca8668f14
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24904
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To comply with all relevant bodies throughout the world, SAR settings
take into account the lowest common denominator Tx power settings. This
setup may lead to non-optimal performance when the user location is in a
country that may allow higher power setting. The purpose of Wireless Geo
Delta Settings (WGDS) is to provide offset settings for FCC, Europe,
Japan and Rest of the world. These offsets would be added (by Intel wifi
driver) to the base SAR Tx Power as defined in WRDS and EWRD
BUG=b:65155728
BRANCH=none
TEST=WGDS ACPI table gets created as expected.
Change-Id: I4f602e3f95ff3545db6cc6e428beb9a36abd9296
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix a linking problem with VBOOT and USE_OPTION_TABLE enabled.
Make use of cbfs_locate_file_in_region() and always search the
cmos_layout.bin in the 'COREBOOT' region.
With this change applied there's no need to include the vboot_locator
in SMM any more, we can't break NVRAM with different CMOS layouts,
and we keep VBOOT and non VBOOT behaviour the same.
Only include cmos_layout.bin and cmos.default in RO region.
Add notes explaining the decisions.
Tested on Intel Sandybridge, builds and boots with vboot enabled.
Change-Id: I10ae94d7936581bbb5ea49384122062bd4934ea5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Type of vbt_len should be size_t, change to fix compiler error
Change-Id: I22798fa0edb98fcb9acc1b2dd52f34a61bc511e9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Put the PCIe clock pins in power-saving mode for the BayHub eMMC bridge to
save power. This requires use of an additional register (Misc control
register 2) and another bit in the existing 'protect' register. The naming
of bit 0 of that register is incorrect, based on the latest datasheet
(14 June 2018) so fix that too.
BUG=b:73726008
BRANCH=none
TEST=boot without this patch:
iotools mem_read32 0xfed80e00
0x0046ffff
With this patch:
$ iotools mem_read32 0xfed80e00
0x00463fff
Also see that the PCIe clock stops when eMMC is idle and can be started by
starting disk activity.
Change-Id: I5ad1467b2e2e151215d2dfd2ce48cd4a451fe480
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/26515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
i2c/alps driver implementation is an exact copy of the i2c/hid driver
with only the addition of ALPS0001_HID. This can be supported by the
i2c/hid driver using the hid field in devicetree which is what glkrvp
mainboard does. So, this change removes the i2c/alps driver which is
anyways unused.
Change-Id: I60761c384f3d800532b2b346272da7be28b77acd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
