Update the COS mask calculation to accomodate the RW data as per SoC
configuration. Currently only one way is allocated for RW data and
configured for non-eviction. For earlier platform this served fine,
and could accomodate a RW data up to 256Kb. Starting TGL and JSL, the
DCACHE_RAM_SIZE is configured for 512Kb, which cannot be mapped to a
single way. Hence update the number of ways to be configured for non-
eviction as per total LLC size.
The total LLC size/ number of ways gives the way size. DCACHE_RAM_SIZE/
way size gives the number of ways that need to be configured for non-
eviction, instead of harcoding it to 1.
TGL uses MSR IA32_CR_SF_QOS_MASK_1(0x1891) and IA32_CR_SF_QOS_MASK_2(0x1892)
as COS mask selection register and hence needs to be progarmmed accordingly.
Also JSL and TGL platforms the COS mask selection is mapped to bit 32:33
of MSR IA32_PQR_ASSOC(0xC8F) and need to be updated in edx(maps 63:32)
before MSR write instead of eax(maps 31:0). This implementation corrects
that as well.
BUG=b:149273819
TEST= Boot waddledoo(JSL), hatch(CML), Volteer(TGL)with NEM enhanced
CAR configuration.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I54e047161853bfc70516c1d607aa479e68836d04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The UART index is never negative, so make it unsigned and drop the
checks for the index to be non-negative.
Change-Id: I64bd60bd2a3b82552cb3ac6524792b9ac6c09a94
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The build error `incompatible-pointer-types` occurs while using
`pci_dev_request_bus_master` as part of device ops
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I3b1ce85b8db1ddf9ac860415edbe64694b91b3d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The IA32_SMRR_PHYS_MASK MSR contains a 'Lock' bit, which will cause the
core to generate a #GP if the SMRR_BASE or SMRR_MASK registers are
written to after the Lock bit is set; this is helpful with securing SMM.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I784d1d1abec0a0fe0ee267118d084ac594a51647
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This adds support for line-buffered console output to System76 EC firmware.
Once the print command is received, the EC firmware multiplexes the output
to any enabled console on the EC. This can be a memory ringbuffer, a
parallel port (using the keyboard connector), or i2c (using the battery
connector). Once the entire buffer is sent, it sets the command register
to 0, indicating completion. For more information, please see:
https://github.com/system76/ec/blob/master/doc/debugging.md
Tested on system76/lemp9 with CONSOLE_SYSTEM76_EC enabled.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I861bf3e22f40dd6c3ec7ba1d73711b399358e332
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
ddr_frequency is ambiguous and is interpreted differently in several
places. Instead of renaming this field, this deprecates it and adds
two new fields with unambiguous naming, max_speed_mts and
configured_speed_mts. smbios.c falls back to using ddr_frequency
when either of these fields are 0.
The same value was being used for both configured memory speed and
max memory speed in SMBIOS type 17, which is not accurate when
configured speed is not the max speed.
BUG=b:167218112
TEST=Boot ezkinil, no change to dmidecode -t17
Change-Id: Iaa75401f9fc33642dbdce6c69bd9b20f96d1cc25
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44549
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code using the macro was found not working after finally enabling
the HDA PCI device on the hermes board.
Fix a typo to generate the correct verbs.
Tested on prodrive/hermes.
Change-Id: I953c2e9fbebc1f02bdf71ce868a95f578300c3a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44900
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a backing cache for all successfully probed fw_config fields that
originated as `probe` statements in the devicetree. This allows recall
of the `struct fw_config` which was probed.
BUG=b:161963281
TEST=tested with follower patch
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0d014206a4ee6cc7592e12e704a7708652330eaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This PCI ID is required in order for the CML devices to perform
SSDT generation for DPTF.
CML Processor, EDS, Vol 1,
Table 9-5, Section 9.2.
BUG=b:158986928
BRANCH=puff
TEST=builds
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Change-Id: I94aea6b9e0f60656827daada7b2cc2741604b8b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Andrew McRae <amcrae@google.com>
It seems that GCC's LTO doesn't like the way we implement
DECLARE_OPTIONAL_REGION(). This patch changes it so that rather than
having a normal DECLARE_REGION() in <symbols.h> and then an extra
DECLARE_OPTIONAL_REGION() in the C file using it, you just say
DECLARE_OPTIONAL_REGION() directly in <symbols.h> (in place and instead
of the usual DECLARE_REGION()). This basically looks the same way in the
resulting object file but somehow LTO seems to like it better.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6096207b311d70c8e9956cd9406bec45be04a4a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Create two new functions to fetch mrc_cache data (replacing
mrc_cache_get_current):
- mrc_cache_load_current: fetches the mrc_cache data and drops it into
the given buffer. This is useful for ARM platforms where the mmap
operation is very expensive.
- mrc_cache_mmap_leak: fetch the mrc_cache data and puts it into a
given buffer. This is useful for platforms where the mmap operation
is a no-op (like x86 platforms). As the name mentions, we are not
freeing the memory that we allocated with the mmap, so it is the
caller's responsibility to do so.
Additionally, we are replacing mrc_cache_latest with
mrc_cache_get_latest_slot_info, which does not check the validity of
the data when retrieving the current mrc_cache slot. This allows the
caller some flexibility in deciding where they want the mrc_cache data
stored (either in an mmaped region or at a given address).
BUG=b:150502246
BRANCH=None
TEST=Testing on a nami (x86) device:
reboot from ec console. Make sure memory training happens.
reboot from ec console. Make sure that we don't do training again.
Signed-off-by: Shelley Chen <shchen@google.com>
Change-Id: I259dd4f550719d821bbafa2d445cbae6ea22e988
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44006
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create areas for console & timestamp data in psp_verstage and pass it to
the x86 to save for use later.
BUG=b:159220781
TEST=Build & Boot trembyle
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I41c8d7a1565e761187e941d7d6021805a9744d06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The assumption was that the fmap cache would be initialized in
bootblock, otherwise an error is shown. This error is showing
up in psp_verstage when the fmap cache is initialized there, so
create a new ENV value for ENV_INITIAL_STAGE.
BUG=None
TEST=Boot, see that error message is gone from psp_verstage
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I142f2092ade7b4327780d423d121728bfbdab247
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43488
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Compiler's instrumentation cannot insert asan memory checks in
case of memory functions like memset, memcpy and memmove as they
are written in assembly.
So, we need to manually check the memory state before performing
each of these operations to ensure that ASan is triggered in case
of bad access.
Change-Id: I2030437636c77aea7cccda8efe050df4b77c15c7
Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch adds ASan support to romstage on x86 architecture.
A Kconfig option is added to enable ASan in romstage. Compiler
flags are updated. A memory space representing the shadow region
is reserved in linker section. And a function call to asan_init()
is added to initialize shadow region when romstage loads.
Change-Id: I67ebfb5e8d602e865b1f5c874860861ae4e54381
Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch adds address sanitizer module to the library and reserves
a linker section representing the shadow region for ramstage. Also,
it adds an instruction to initialize shadow region on x86
architecture when ramstage is loaded.
Change-Id: Ica06bd2be78fcfc79fa888721ed920d4e8248f3b
Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add code for IVRS generation to coreboot. Publish coreboot generated
structure rather than IVRS generated by FSP binary.
Reference Doc: 48882_IOMMU_3.05_PUB.pdf
BUG=b:155307433
TEST=Boot trembyle to shell and extract and compare IVRS tables and make
sure they cover the same devices.
Change-Id: I693f4399766c71c3ad53539634c65ba59afd0fe1
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* On ARCH_RAMSTAGE_X86_64 jump to the payload in protected mode.
* Add a helper function to jump to arbitrary code in protected mode,
similar to the real mode call handler.
* Doesn't affect existing x86_32 code.
* Add a macro to cast pointer to uint32_t that dies if it would overflow
on conversion
Tested on QEMU Q35 using SeaBIOS as payload.
Tested on Lenovo T410 with additional x86_64 patches.
Change-Id: I6552ac30f1b6205e08e16d251328e01ce3fbfd14
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The wake source macro for GPE events was using 'GPIO'. However,
current usage is really all GPEs. Therefore, provide clarity
in the naming in order to allow for proper GPIO wake events
that are separate from the ACPI GPE block.
BUG=b:159947207
Change-Id: I27d0ab439c58b1658ed39158eddb1213c24d328f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable long mode in SMM handler.
x86_32 isn't affected by this change.
* Enter long mode
* Add 64bit entry to GDT
* Use x86_64 SysV ABI calling conventions for C code entry
* Change smm_module_params' cpu to size_t as 'push' is native integer
* Drop to protected mode after c handler
NOTE: This commit does NOT introduce a new security model. It uses the
same page tables as the remaining firmware does.
This can be a security risk if someone is able to manipulate the
page tables stored in ROM at runtime. USE FOR TESTING ONLY!
Tested on Lenovo T410 with additional x86_64 patches.
Change-Id: I26300492e4be62ddd5d80525022c758a019d63a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eugene Myers <cedarhouse1@comcast.net>
This can be used in romstage in particular to know if dram is ready.
Change-Id: I0231ab9c0b78a69faa762e0a97378bf0b50eebaf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
INVD is called below so if postcar is running in a cached environment
it needs to happen.
NOTE: postcar cannot execute in a cached environment if clflush is not
supported!
Change-Id: I37681ee1f1d2ae5f9dd824b5baf7b23b2883b1dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Xeon-SP Skylake Scalable Processor can have 36 CPU threads (18 cores).
Current coreboot SMM is unable to handle more than ~32 CPU threads.
This patch introduces a version 2 of the SMM module loader which
addresses this problem. Having two versions of the SMM module loader
prevents any issues to current projects. Future Xeon-SP products will
be using this version of the SMM loader. Subsequent patches will
enable board specific functionality for Xeon-SP.
The reason for moving to version 2 is the state save area begins to
encroach upon the SMI handling code when more than 32 CPU threads are
in the system. This can cause system hangs, reboots, etc. The second
change is related to staggered entry points with simple near jumps. In
the current loader, near jumps will not work because the CPU is jumping
within the same code segment. In version 2, "far" address jumps are
necessary therefore protected mode must be enabled first. The SMM
layout and how the CPUs are staggered are documented in the code.
By making the modifications above, this allows the smm module loader to
expand easily as more CPU threads are added.
TEST=build for Tiogapass platform under OCP mainboard. Enable the
following in Kconfig.
select CPU_INTEL_COMMON_SMM
select SOC_INTEL_COMMON_BLOCK_SMM
select SMM_TSEG
select HAVE_SMI_HANDLER
select ACPI_INTEL_HARDWARE_SLEEP_VALUES
Debug console will show all 36 cores relocated. Further tested by
generating SMI's to port 0xb2 using XDP/ITP HW debugger and ensured all
cores entering and exiting SMM properly. In addition, booted to Linux
5.4 kernel and observed no issues during mp init.
Change-Id: I00a23a5f2a46110536c344254868390dbb71854c
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The device is a PCIe to eMMC bridge controller to be used in the
Chromebook as the boot disk. The datasheet name is GL9763E and
the revision is 02.
The patch sets single request AXI, disables ASPM L0s and enables SSC.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: I158c79f5ac6e559f335b6b50092469c7b1646c56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove const struct imd *imd and const struct imdr *imdr parameters from
the prototypes of imdr_entry_size(), imd_entry_size() and imd_entry_id()
functions since they are not used anywhere.
Signed-off-by: Anna Karas <aka@semihalf.com>
Change-Id: I6b43e9a5ae1f1d108024b4060a04c57f5d77fb55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43999
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Many places in coreboot seem to like to do things like
assert(CONFIG(SOME_KCONFIG));
This is somewhat suboptimal since assert() is a runtime check, so you
don't see that this fails until someone actually tries to boot it even
though the compiler is totally aware of it already. We already have the
dead_code() macro to do this better:
if (CONFIG(SOME_KCONFIG))
dead_code();
Rather than fixing all these and trying to carefully educate people
about which type of check is more appropriate in what situation, we can
just employ the magic of __builtin_constant_p() to automatically make
the former statement behave like the latter.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I06691b732598eb2a847a17167a1cb92149710916
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TEST=Execute "dmidecode -t 4" to check if the processor information is correct for Deltalake platform
Change-Id: I5d075bb297f2e71a2545ab6ad82304a825ed7d19
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `GetPhysicallyInstalledSystemMemory` API call, at least on Windows
10, returns an error if SMBIOS tables are invalid. Various tools use
this API call and don't operate correctly if this fails. For example,
the "Intel Processor Diagnostic Tool" program is affected.
Windows then guesses the physical memory size by accumulating entries
from the firmware-provided memory map, which results in a total memory
size that is slightly lower than the actual installed memory capacity.
To fix this issue, add the handle to a type 16 entry to all type 17
entries.
Add new fields to struct memory_info and fill them in Intel common code.
Use the introduced variables to fill type 16 in smbios.c and provide
a handle to type 17 entries.
Besides keeping the current behaviour on intel/soc/common platforms, the
type 16 table is also emitted on platforms that don't explicitly fill
it, by using the existing fields of struct memory_info.
Tested on Windows 10:
The GetPhysicallyInstalledSystemMemory API call doesn't return an error
anymore and the installed memory is now being reported as 8192 MiB.
Change-Id: Idc3a363cbc3d0654dafd4176c4f4af9005210f42
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fill in the new fields introduced with version 3.0 and install the new
entry point structure identified by _SM3_.
Tested on Linux 5.6 using tianocore as payload:
Still able to decode the tables without errors.
Change-Id: Iba7a54e9de0b315f8072e6fd2880582355132a81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This adds the PCI ID of the realtek 5261 PCIe to SD Express card
reader.
BUG=b:161774205
TEST=none
Change-Id: I4d5e6cfca59b02adc74a0c148281a92421fe209d
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Looks like no one really knows what this bit would be useful for, nor
when it would need to be set. Especially if coreboot is setting it even
on PCI *Express* bridges. Digging through git history, nearly all
instances of setting it on PCIe bridges comes from i82801gx, for which
no reason was given as to why this would be needed. The other instances
in Intel code seem to have been, unsurprisingly, copy-pasted.
Drop all uses of this definition and rename it to avoid confusion. The
negation in the name could trick people into setting this bit again.
Tested on Asrock B85M Pro4, no visible difference.
Change-Id: Ifaff29561769c111fb7897e95dbea842faec5df4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Remove the obscure path in source code, where ACPI S3 resume
was prohibited and acpi_resume() would return and continue
to BS_WRITE_TABLES.
The condition when ACPI S3 would be prohibited needs to be
checked early in romstage already. For the time being, there
has been little interest to have CMOS option to disable
ACPI S3 resume feature.
Change-Id: If5105912759427f94f84d46d1a3141aa75cbd6ef
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This lets code that run in userspace notify coreboot of that fact so
things that can't run in userspace can be excluded.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I4da414bc96cfcf0464125eddc6b3f3a7b4506fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43784
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Mark the CPU as enabled and the socket as populated.
EDK2 tests these flags before further reading this structure.
Change-Id: Ic545bb47c502cb9d2352ba6d43eaed8c97229c02
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43703
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement type 19 by accumulating the DRAM dimm size found in cbmem's
CBMEM_ID_MEMINFO structure. This seems common on x86 where the
address space always starts at 0.
At least EDK2 uses this table in the UI and shows 0 MB DRAM if not
present.
Change-Id: Idee8b8cd0b155e14d62d4c12893ff01878ef3f1c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
It's not stricly related to spinlocks. If defined, a better
location should be found and the name collisions with other
barrier() defined in nb/intel solved.
Change-Id: Iae187b5bcc249c2a4bc7bee80d37e34c13d9e63d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43810
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's not related to spinlocks and the actual implementation
was also guarded by CONFIG(SMP).
With a single call-site in x86-specific code, empty stubs
for other arch are currently not necessary.
Also drop an unused included on a nearby line.
Change-Id: I00439e9c1d10c943ab5e404f5d687d316768fa16
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43808
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are many places where we do this. Put it inside an inline function
for convenience reasons.
Change-Id: I5515a52458b6c78c1a723cb08e6471eb9bac9cd6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43871
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates Tiger Lake SA DID and report platform. According to
doc #613584, remove PCI_DEVICE_ID_INTEL_TGL_ID_U_1 and add below
definitions of SA ID for TGL-UP4 skus:
TGL-UP4(Y) (4+2): PCI_DEVICE_ID_INTEL_TGL_ID_Y_4_2 0x9A12h
TGL-UP4(Y) (2+2): PCI_DEVICE_ID_INTEL_TGL_ID_Y_2_2 0x9A02h
Change-Id: Id9d9c9ac3bf39582b0da610e6ef912031939c763
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43061
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When refactoring, one can move code around quite a bit while preserving
reproducibility, unless there is an assert-style macro somewhere... As
these macros use __FILE__ and __LINE__, just moving them is enough to
change the resulting binary, making timeless builds rather useless.
To improve reproducibility, do not use __FILE__ nor __LINE__ inside the
assert-style macros. Instead, use hardcoded values. Plus, mention that
timeless builds lack such information in place of the file name, so that
grepping for the printed string directs one towards this commit. And for
the immutable line number, we can use 404: line number not found :-)
Change-Id: Id42d7121b6864759c042f8e4e438ee77a8ac0b41
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All supported x86 chips select HAVE_CF9_RESET, and also use 0xcf9 as
reset register in FADT. How unsurprising. We might as well use that
information to automatically fill in the FADT accordingly. So, do it.
To avoid having x86-specific code under arch-agnostic `acpi/`, create a
new optional `arch_fill_fadt` function, and override it for x86 systems.
Tested on Asus P8Z77-V LX2 with Linux 5.7.6 and Windows 10 at the end of
the patch train, both operating systems are able to boot successfully.
Change-Id: Ib436b04aafd66c3ddfa205b870c1e95afb3e846d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
In the initial DPTF refactor, the scope of the TCPU device was
incorrectly set as \_SB, instead of \_SB.PCI0. However, because of the
way that the acpi_inject_dsdt() callback currently works (it injects
contents before the dsdt.aml file), the Scope where the TCPU
device lives (\_SB.PCI0) doesn't exist yet. Therefore, to avoid playing
games with *when* things are defined in the DSDT, switch to defining all
of the DPTF devices in the SSDT.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia4922b4dc6544d79d44d39e6ad18c6ab9fee0fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43529
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change increases the maximum length of device path string to 40
characters to accommodate growing hierarchy of devices.
TEST=Ensured that "\_SB.PCI0.LPCB.EC0.CREC.TUN0.RT58" is correctly
added to SSDT.
Change-Id: Id2ef71a32b26e366b56c652942a247de4889544a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This PCI ID is required in order for JSL devices to perform SSDT
generation for DPTF.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I42209d15bc4f1654814465ce1412576f7349dddc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43421
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new IGD device ID for new Tigerlake SKU support.
BUG=b:160394260
Branch=None
TEST=build, boot and check IGD device is reported.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I1903d513b61655d0e939f80b0fd0108091fdd7e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
There is some boilerplate required to iterate over the USB supported
protocol structs. Encapsulate all the in a method to make the callers
simpler.
BUG=b:154756391
TEST=Built test trembyle.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I401f10d242638b0000ba697573856d765333dca0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43352
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Code has evolved such that there seems to be little
use for global definition of cbmem_top_chipset().
Even for AMD we had three different implementations.
Change-Id: I44805aa49eab526b940e57bd51cd1d9ae0377b4b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43326
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI names can only be 4 characters long. Define a constant that defines
the size of the name + the NUL terminator.
BUG=b:154756391
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iad230c029f324005620ddad66c433ada26be78cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This code is not even being build-tested. Drop it before it grows moss.
Change-Id: I216f8459afc69ced98ea1859ee6b1f8e4d43bc4a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
The SMM_LOCK bit isn't in SMM_MASK_MSR, but in HWCR_MSR, so move it
there. The soc/amd/* code itself uses the bit definition when accessing
HWCR_MSR, so SMM_LOCK was just below the wrong MSR definition.
Also remove SMM_LOCK from comment about masking bits in SMM_MASK_MSR,
since that bit isn't in that MSR.
TEST=Checked the code and the corresponding BKDG/PPR.
Change-Id: I2df446f5a9e11e1e7c8d10256f3c2803b18f9088
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43309
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A fairly common thing in ACPI is notifying a device when some kind of
device-specific event happens; this function simplifies writing this
pattern.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0f18db9cc836ec9249604452f03ed9b4c6478827
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42102
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel Dynamic Tuning Technology is the name of a PCI device on some
Intel SoCs. This minimal PCI driver is only used now for SSDT generation
on TGL devices.
Change-Id: Ib52f35e4e020ca3e6ab8b32cc3bf7df36041926e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41893
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Specify how hexstrtobin.c processes the strings of odd length.
Signed-off-by: Anna Karas <aka@semihalf.com>
Change-Id: Ie8cd8fb93d7dab08c5e7f28fc511b6381f5ad13a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43089
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
\_SB.DPTF.IDSP adverties to the DPTF daemon which policies the
implementation supports. Added a new acpigen function to figure out
which policies are used, and fills out IDSP appropriately.
Change-Id: Idf67a23bf38de4481c02f98ffb27afb8ca2d1b7b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
DPTF has several options on how to control the fan (fine-grained speed
control, minimum speed change in percentage points, and whether or not
the DPTF device should notify the Fan if it detects low speed).
Individual TSRs can also set GTSH, which is the amount of hysteresis
inherent in the measurement, either from circuitry (if analog), or in
firmware (if digital).
BUG=b:143539650
TEST=compiles
Change-Id: I42d789d877da28c163e394d7de5fb1ff339264eb
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds support for emitting the PPCC table, which describes
the ranges available as knobs for DPTF to tune. It can support min/max
power, min/max time window for averaging, and the minimum adjustment size
(granularity or step size) of each power limit. The current implementation
only supports PL1 and PL2.
BUG=b:143539650
TEST=compiles
Change-Id: I67e80d661ea5bb79980ef285eca40c9a4b0f1849
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds support for generating the _FPS table for the DPTF Fan
object. The table describes different levels of fan activity that may be
applied to the system in order to actively cool it. The information
includes fan speed at a (rough) percentage level, fan speed in RPM,
potential noise level in centibels, and power in mA.
BUG=b:143539650
TEST=compiles
Change-Id: I5591eb527f496d0c4c613352d2a87625d47d9273
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change generates the DPTF TCHG.PPSS table in the SSDT. This table
describes different charging rates which are available to use. DPTF
can pick different rates in order to passively cool (or not) the
system.
BUG=b:143539650
TEST=compiles
Change-Id: I6df6bfbac628fa4e4d313e38b8e6c53fce70a7f2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch adds support for DPTF Critical Policies, which are consist
of Method definitions only. They are `_CRT` and `_HOT`, which are
defined as temperature thresholds that, when exceeded, will execute a
graceful suspend or a graceful shutdown, respectively.
BUG=b:143539650
TEST=compiles
Change-Id: I711ecdcf17ae8f6e653f33069201da4515ace85e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch adds support for emitting the Thermal Relationship Table, as
well as _PSV Methods, which together form the basis for DPTF Passive
Policies.
BUG=b:143539650
TEST=compiles
Change-Id: I82e1c9022999b0a2a733aa6cd9c98a850e6f5408
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds support for generating the different pieces of DPTF
Active Policies. This includes the Active Relationship Table, in
addition to _ACx methods.
BUG=b:143539650
TEST=compiles
Change-Id: Iea0ccbd96f88d0f3a8f2c77a7d0f3a284e5ee463
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds support function to add STA function which returns an
external variable.
Change-Id: I31755a76ee985ee6059289ae194537d531270761
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42245
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the certain postcode values aren't in increasing
order of values.
The change, just reorganzies the defines in increasing order
of the values
Signed-off-by: Sindhoor Tilak <sindhoor@sin9yt.net>
Change-Id: Id5f0ddc4593f689829ab9a7fdeebd5f66939bf79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Refer to section 7.9 Port Connector Information of DSP0134_3.3.0
to add type 8 data, the table of data should be ported according
to platform design and MB silkscreen.
Change-Id: I81e25d27c9c6717750edf1d547e5f4cfb8f1da14
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
As per ACPI spec, GpioIo does not have any polarity associated with
it. Linux kernel uses `active_low` argument within GPIO _DSD property
to allow BIOS to indicate if the corresponding GPIO should be treated
as active low. Thus, if GPIO has active high polarity or if it does
not have any polarity associated with it, then the `active_low`
argument is supposed to be set to 0.
Having a `polarity` field in acpi_gpio seems confusing because GPIOs
might not always have polarity associated with them. Example, in case
of DMIC-select GPIO where 0 means select DMIC0 and 1 means select
DMIC1, there is no polarity associated with the GPIO. Thus, it would
be clearer for mainboard to use macros without having to specify a
particular polarity. In order to enable mainboards to provide GPIO
information without polarity for GpioIo usage, this change also adds
`ACPI_GPIO_OUTPUT` and `ACPI_GPIO_INPUT` macros.
BUG=b:157603026
Change-Id: I39d2a6ac8f149a74afeb915812fece86c9b9ad93
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds helper macros for initializing acpi_gpio fields
for GpioIo/GpioInt objects. This allows dropping some redundant code
for each macro to set the structure fields.
Change-Id: Id0a655468759ed3035c6c1e8770e37f1275e344e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Bring all GNVS related initialisation function to global
scope to force identical signatures. Followup work is
likely to remove some as duplicates.
Change-Id: Id4299c41d79c228f3d35bc7cb9bf427ce1e82ba1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42489
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For type 3, override chassis asset_tag_number with smbios_mainboard_asset_tag()
and add two functions that can override chassis version and serial_number.
For type 4 add smbios_processor_serial_number() to override serial_number.
Tested on OCP Tioga Pass.
Change-Id: I80c6244580a4428fab781d760071c51c7933abee
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Except for whitespace and varying casts the codes were
the same when implemented.
Platforms that did not implement this are tagged with
ACPI_NO_SMI_GNVS.
Change-Id: I31ec85ebce03d0d472403806969f863e4ca03b6b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide common initialisation point for setting up
GNVS structure before first SMI is triggered.
Change-Id: Iccad533c3824d70f6cbae52cc8dd79f142ece944
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42423
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most LAPIC registers are 32bit, and thus the use of long is valid on
x86_32, however it doesn't work on x86_64.
* Don't use long as it is 64bit on x86_64, which breaks interrupts
in QEMU and thus SeaBIOS wouldn't time out the boot menu
* Get rid of unused defines
* Get rid of unused atomic xchg code
Tested on QEMU Q35 with x86_64 enabled: Interrupts work again.
Tested on QEMU Q35 with x86_32 enabled: Interrupts are still working.
Tested on Lenovo T410 with x86_64 enabled.
Change-Id: Iaed1ad956d090625c7bb5cd9cf55cbae16dd82bd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36777
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change is required so we have a defined entry point on S3. Without
this, the S3_RESUME_EIP_MSR register could in theory be written to
later which would be a security risk.
BUG=b:147042464
TEST=Resume trembyle and see bootblock start.
coreboot-4.12-512-g65779ebcf73f-dirty Thu Jun 4 22:38:17 UTC 2020 smm starting (log level: 8)...
SMI# #6
SMI#: SLP = 0x0c01
Chrome EC: Set SMI mask to 0x0000000000000000
Chrome EC: Set SCI mask to 0x0000000000000000
Clearing pending EC events. Error code EC_RES_UNAVAILABLE(9) is expected.
EC returned error result code 9
SMI#: Entering S3 (Suspend-To-RAM)
PSP: Prepare to enter sleep state 3... OK
SMU: Put system into S3/S4/S5
Timestamp - start of bootblock: 18446744070740509170
coreboot-4.12-512-g65779ebcf73f-dirty Thu Jun 4 22:38:17 UTC 2020 bootblock starting (log level: 8)...
Family_Model: 00810f81
PMxC0 STATUS: 0x200800 SleepReset BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
Timestamp - end of bootblock: 18446744070804450274
VBOOT: Loading verstage.
FMAP: area COREBOOT found @ c75000 (3715072 bytes)
CBFS: Locating 'fallback/verstage'
CBFS: Found @ offset 61b80 size cee4
PROG_RUN: Setting MTRR to cache stage. base: 0x04000000, size: 0x00010000
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4b0b0d0d576fc42b1628a4547a5c9a10bcbe9d37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Old (!PARALLEL_MP) cpu bringup uses this as the first
control to do SMM relocation.
Change-Id: I4241120b00fac77f0491d37f05ba17763db1254e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
With RELOCATABLE_RAMSTAGE the backing up of low memory
on S3 resume path was dropped. We forgot some things
behind.
Change-Id: I674f23dade0095e64619af0ae81e23368b1ee471
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Once we support building stages for different architectures,
such CONFIG(ARCH_xx) tests do not evaluate correctly anymore.
Change-Id: I599995b3ed5c4dfd578c87067fe8bfc8c75b9d43
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42183
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add a function to check if a region overlaps with SMM.
* Add a function to check if a pointer points to SMM.
* Document functions in Documentation/security/smm
To be used to verify data accesses in SMM.
Change-Id: Ia525d2bc685377f50ecf3bdcf337a4c885488213
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41084
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The call made at mp_ops.post_mp_init() generally
uses four different names. Unify these with followups.
smm_southbridge_enable(SMI_EVENTS)
smm_southbridge_enable_smi()
hudson_enable_smi_generation()
enable_smi_generation()
Furthermore, some platforms do not enable power button
SMI early. It may be preferred to delay the enablement,
but fow now provide global_smi_enable_no_pwrbtn() too.
Change-Id: I6a28883ff9c563289b0e8199cd2ceb9acd6bacda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Attempts to write to APM_CNT IO port should always be guarded
with a test to verify SMI handler has been installed.
Immediate followup removes redundant HAVE_SMI_HANDLER tests.
Change-Id: If3fb0f1a8b32076f1d9f3fea9f817dd4b093ad98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41971
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cbmem is not online when vboot runs before the bootblock. Update the
macro to reflect that.
BUG=b:158124527
TEST=Build & boot psp_verstage on trembyle
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I6fb4ad04f276f2358ab9d4d210fdc7a34a93a5bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
When adding XIP stages on x86, the -P parameter was used to
pass a page size that covers the entire file to add. The same
can now be achieved with --pow2page and we no longer need to
define a static Konfig for the purpose.
TEST: Build asus/p2b and lenovo/x60 with "--pow2page -v -v" and
inspect the generated make.log files. The effective pagesize is
reduced from 64kB to 16kB for asus/p2b giving more freedom
for the stage placement inside CBFS. Pagesize remained at 64kB
for lenovo/x60.
Change-Id: I5891fa2c2bb2d44077f745619162b143d083a6d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
• Based on FSP EAS v2.1 – Backward compatibility is retained.
• Add multi-phase silicon initialization to increase the modularity of the
FspSiliconInit() API.
• Add FspMultiPhaseSiInit() API
• FSP_INFO_HEADER changes
o Added FspMultiPhaseSiInitEntryOffset
• Add FSPS_ARCH_UPD
o Added EnableMultiPhaseSiliconInit, bootloaders designed for
FSP 2.0/2.1 can disable the FspMultiPhaseSiInit() API and
continue to use FspSiliconInit() without change.
FSP 2.2 Specification:
https://www.intel.com/content/www/us/en/intelligent-systems/intel-firmware-support-package/intel-fsp-overview.html
Change-Id: If7177a267f3a9b4cbb60a639f1c737b9a3341913
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41728
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the comments of
https://review.coreboot.org/c/coreboot/+/41719
, which is about Microcode patch for amd/picasso.
Change the code with the same way.
The changes include:
1. combine the microcode_xxx.c and update_microcode.c
into one source.
2. Redefine the microcode updating function to eliminate
the parameter. Get the revision ID in the black box.
Reduce the depth of function calls.
3. Get the revision ID by bitwise calculation instead of
lookup table.
4. Reduce the confusing type casts.
5. Squash some lines.
We do not change the way it used to be. The code assume
only one microcode is integrated in CBFS. If needed in future,
41719 is the example of integrating multiple binaries.
And, 41719 depends on the definition in this patch.
Change-Id: I8b0da99db0d3189058f75e199f05492c4e6c5881
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This MSR is used for detecting if the micro code is applied
successfully.
Change-Id: I060eb1a31f3358341ac0d5b9105e710c351f2ce8
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42212
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the sake of completeness, we should provide these operations.
Change-Id: Ia28af94ec86319c7380d8377f7e24e5cdf55dd9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42145
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only Winbond parts seem to support making status register writes
volatile. So this flag should not be exposed in the generic interface.
Change-Id: Idadb65ffaff0dd7809b18c53086a466122b37c12
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41746
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A function pci_dev_disable_bus_master() is created. This function
can be used to disable Thunderbolt PCIe root ports, bridges and
devices for Vt-d based security platform at end of boot service.
BUG=None
TEST=Verified PCIe device bus master enable bit is cleared.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ie92a15bf2c66fdc311098acb81019d4fb7f68313
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Advertising SMI triggers in FADT is only valid if we exit with
SMI installed. There has been some experiments to delay SMM
installation to OS, yet there are new platforms that allow some
configuration access only to be done inside SMM.
Splitting static HAVE_SMI_HANDLER variable helps to manage cases
where SMM might be both installed and cleared prior to entering
payload.
Change-Id: Iad92c4a180524e15199633693446a087787ad3a2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There have been changes to the way device properties are supported
in Linux[1] and Windows[2] which add flexibilty:
- non-standard UUIDs can be used instead of only ACPI_DP_UUID
- support for multiple different packages within the _DSD that
associate different properties with unique UUIDs.
To handle this I extracted the part that does the write of UUID and
properties to a separate function and defined a new PACKAGE type
which has the custom UUID as a name and can be used the same way that
child properties are today.
For example a PCIe root port for a USB4 port has a standard property
indicating the USB4 reference, and then two custom properties which
are defined for different attributes.
Example code:
/* Create property table */
acpi_dp *dsd = acpi_dp_new_table("_DSD");
acpi_dp_add_reference(dsd, "usb4-port", usb4_path);
/* Add package for hotplug */
acpi_dp *pkg = acpi_dp_new_table("6211e2c0-58a3-4af3-90e1-927a4e0c55a4");
acpi_dp_add_integer(pkg, "HotPlugSupportInD3", 1);
acpi_dp_add_package(dsd, pkg);
/* Add package for external port info */
pkg = acpi_dp_new_table("efcc06cc-73ac-4bc3-bff0-76143807c389");
acpi_dp_add_integer(pkg, "ExternalFacingPort", 1);
acpi_dp_add_package(dsd, pkg);
/* Write all properties */
acpi_dp_write(dsd);
Resulting ACPI:
Scope (\_SB.PCI0.TRP0)
{
Name (_DSD, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package ()
{
Package () { "usb4-port", \_SB.PCI0.TDM0.RHUB.PRTA }
},
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package ()
{
Package () { "HotPlugSupportInD3", One }
},
ToUUID ("efcc06cc-73ac-4bc3-bff0-76143807c389"),
Package ()
{
Package () { "ExternalFacingPort", One },
}
})
}
[1] https://patchwork.kernel.org/patch/10599675/
[2] https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
Change-Id: I75f47825bf4ffc5e9e92af2c45790d1b5945576e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These build on existing functions but use different object types
in order to provide functions for upcoming changes:
acpigen_write_return_op(): Return an operator.
acpigen_write_if_lequal_op_op(): Check if 2 operands are equal.
acpigen_get_package_op_element(): Read an element from a package
into an operator.
This one just provides the missing helper, the other 3 already exist:
acpigen_get_tx_gpio: Read TX gpio state.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I1141fd132d6f09cf482f74e95308947cba2c5846
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41985
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The definition of processor_rev_id in struct microcode
is 16 bits. So we need to change the a series of parameters
passing to 16 bits.
Change-Id: Iacabee7e571bd37f3aca106d515d755969daf8f3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change introduces a new top-level interface for interacting with a
bitmask providing firmware configuration information.
This is motivated by Chromebook mainboards that need to support multiple
different configurations at runtime with the same BIOS. In these
devices the Embedded Controller provides a bitmask that can be broken
down into different fields and each field can then be broken down into
different options.
The firmware configuration value could also be stored in CBFS and this
interface will look in CBFS first to allow the Embedded Controller value
to be overridden.
The firmware configuration interface is intended to easily integrate
into devicetree.cb and lead to less code duplication for new mainboards
that make use of this feature.
BUG=b:147462631
TEST=this provides a new interface that is tested in subsequent commits
Change-Id: I1e889c235a81545e2ec0e3a34dfa750ac828a330
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's not a function that is the equivalent to
x86_setup_mtrrs_with_detect() but not solving for above 4GiB.
Provide x86_setup_mtrrs_with_detect_no_above_4gb() which is the
equivalent to x86_setup_mtrrs_with_detect() but instructs the MTRR
solver to not take into account memory above 4GiB.
BUG=b:155426691
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia1b5d67d6f139aaa929e03ddbc394d57dfb949e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41897
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Introduce concept of var_mtrr_context object for tracking and
assigning MTRR values. The algorithm is lifted from postcar_loader
code, but it's generalized for different type of users: setting
MSRs explicitly or deferring to a particular caller's desired
actions.
BUG=b:155426691,b:155322763
Change-Id: Ic03b4b617196f04071093bbba4cf28d23fa482d8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
<types.h> is supposed to provide <commonlib/bsd/cb_err.h>,
<stdbool.h>,<stdint.h> and <stddef.h>. So remove those includes
each time when <types.h> is included.
Change-Id: I886f02255099f3005852a2e6095b21ca86a940ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We want to use the CACHE_ROM_* macros in linker scripts. Avoid
`commonlib/helpers.h` as it contains an ALIGN() macro definition
that conflicts with the ALIGN keyword in linker scripts.
Change-Id: I3bf20733418ca4135f364a3f6489e74d45e4f466
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41785
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI device sleep states are different from system sleep states
and many places hardcode to specific values that are difficult to
decode without referring to the spec.
Change-Id: If5e732725b775742fd2a9fd0df697e312aa7bf20
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41791
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The USB Type-C Connector Class in the Linux kernel is not specific to
the ChromeOS EC, so this functionality is now split out into a separate
file, acpigen_usb.c. Documentation about the kernel side is available at
https://www.kernel.org/doc/html/latest/driver-api/usb/typec.html.
Change-Id: Ife5b8b517b261e7c0068c862ea65039c20382c5a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41539
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds back CB:39487 which was reverted as part of
CB:41412. Now that the resource allocator is split into old(v3) and
new(v4), this change adds support for allocating resources above 4G
boundary with the new allocator v4.
Original commit message:
This change adds support for allocating resources above the 4G
boundary by making use of memranges for resource windows enabled in
the previous CL.
It adds a new resource flag IORESOURCE_ABOVE_4G which is used in the
following ways:
a) Downstream device resources can set this flag to indicate that they
would like to have their resource allocation above the 4G
boundary. These semantics will have to be enabled in the drivers
managing the devices. It can also be extended to be enabled via
devicetree. This flag is automatically propagated by the resource
allocator from downstream devices to the upstream bridges in pass
1. It is done to ensure that the resource allocator has a global view
of downstream requirements during pass 2 at domain level.
b) Bridges have a single resource window for each of mem and prefmem
resource types. Thus, if any downstream resource of the bridge
requests allocation above 4G boundary, all the other downstream
resources of the same type under the bridge will be allocated above 4G
boundary.
c) During pass 2, resource allocator at domain level splits
IORESOURCE_MEM into two different memory ranges -- one for the window
below 4G and other above 4G. Resource allocation happens separately
for each of these windows.
d) At the bridge level, there is no extra logic required since the
resource will live entirely above or below the 4G boundary. Hence, all
downstream devices of any bridge will fall within the window allocated
to the bridge resource. To handle this case separately from that of
domain, initializing of memranges for a bridge is done differently
than the domain.
Limitation:
Resources of a given type at the bridge or downstream devices
cannot live both above and below 4G boundary. Thus, if a bridge has
some downstream resources requesting allocation for a given type above
4G boundary and other resources of the same type requesting allocation
below 4G boundary, then all these resources of the same type get
allocated above 4G boundary.
Change-Id: I92a5cf7cd1457f2f713e1ffd8ea31796ce3d0cce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change moves the resource allocator functions out of device.c
and into two separate files:
1. resource_allocator_v3.c: This is the old implementation of
resource allocator that uses a single window for resource
allocation. It is required to support some AMD chipsets that do not
provide an accurate map of allocated resources by the time the
allocator runs. They work fine with the old allocator since it
restricts itself to allocations in a single window at the top of the
4G space.
2. resource_allocator_common.c: This file contains the functions that can
be shared by the old and new resource allocator.
Entry point into the resource allocation is allocate_resources() which
can be implemented by both old and new allocators. This change also
adds a Kconfig option RESOURCE_ALLOCATOR_V3 which enables the old
resource allocator. This config option is enabled by default
currently, but in the following CLs this will be enabled only for the
broken boards.
Reason for this split: Both the old and new resource allocators need
to be retained in the tree until the broken chipsets are fixed.
Change-Id: I2f5440cf83c6e9e15a5f22e79cc3c66aa2cec4c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41442
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After removal of CAR_MIGRATION there are no more reasons
to carry around ENV_STAGE_HAS_BSS_SECTION=n case.
Replace 'MAYBE_STATIC_BSS' with 'static' and remove explicit
zero-initializers.
Change-Id: I14dd9f52da5b06f0116bd97496cf794e5e71bc37
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The ALC5682 headset codec can be connected over SoundWire and be
configured for mainboards to use:
- Data Port 0 and Bulk Register Access is supported
- Data Ports 1-4 are supported as both source and sink
The data port and audio mode properties are filled out as best as
possible with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
For example this device is connected to master link ID 0 and has strap
settings configuring it for unique ID 1:
chip drivers/soundwire/alc5682
register "desc" = ""Headset Codec""
device generic 0.1 on end
end
This driver was tested with the volteer reference design by booting
and disassembling the runtime SSDT to ensure that the devices have the
expected address and properties.
Device (SW01)
{
Name (_ADR, 0x000021025D568200)
Name (_DDN, "Headset Codec")
Name (_DSD, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-sw-interface-revision", 0x00010000 },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-bra-mode-0", "BRA0" },
Package () { "mipi-sdw-dp-0-subproperties", "DP0" },
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" },
Package () { "mipi-sdw-dp-1-source-subproperties", "SRC1" },
Package () { "mipi-sdw-dp-1-sink-subproperties", "SNK1" },
[...]
}
}
Name (BRA0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {
"mipi-sdw-bra-mode-bus-frequency-configs",
Package () { 0x000F4240, [...] }
},
[...]
}
}
Name (DP0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-bra-flow-controlled", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-bra-mode-0", "BRA0" }
}
}
Name (MOD0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {
"mipi-sdw-audio-mode-bus-frequency-configs",
Package () { 0x000F4240, [...] }
},
[...]
}
}
Name (SNK1, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
}
Name (SNK1, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
}
}
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I488dcd81d2e66a6f2c269ab7fa9f7ceaf2cbf003
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40891
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MAX98373 smart speaker amp can be connected over SoundWire and be
configured for mainboards to use:
- Data Port 0 and Bulk Register Access is not supported
- Data Port 1 is the 32bit data input for the speaker path
- Data Port 3 is the 16bit data output for I/V sense ADC path
The data port and audio mode properties are filled out as best as
possible with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
For example this device is connected to master link ID 1 and has strap
settings configuring it for unique ID 3.
chip drivers/soundwire/max98373
register "desc" = ""Left Speaker Amp""
device generic 1.3 on end
end
This driver was tested with the volteer reference design by booting
and disassembling the runtime SSDT to ensure that the devices have the
expected address and properties.
Device (SW13)
{
Name (_ADR, 0x000123019F837300)
Name (_DDN, "Left Speaker Amp")
Method (_STA)
{
Return (0x0F)
}
Name (_DSD, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-sw-interface-revision", 0x00010000 },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" },
Package () { "mipi-sdw-dp-1-sink-subproperties", "SNK1" },
Package () { "mipi-sdw-dp-3-source-subproperties", "SRC3" },
}
}
Name (MOD0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {
"mipi-sdw-audio-mode-bus-frequency-configs",
Package () { 0x00753000, [...] }
},
[...]
}
}
Name (SNK1, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
}
Name (SRC3, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package () {
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
}
}
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I3f8cb2779ddde98c5df739bd8a1e83a12a305c00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change adds a help function to write a SoundWire ACPI address
object that conforms to the SoundWire DisCo Specification Version 1.0
The SoundWire address structure is defined in include/device/soundwire.h
and provides the properties that are used to form the _ADR object.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I6efbf52ce20b53f96d69efe2bf004b98dbe06552
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40885
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses the previously added SoundWire definitions to provide
functions that generate ACPI Device Properties for SoundWire
controllers and codecs.
A SoundWire controller driver should populate
`struct soundwire_controller` and pass it to
soundwire_gen_controller(). This will add all of the defined master
links provided by the controller.
A SoundWire codec driver should populate the necessary members in
struct soundwire_codec and pass it to soundwire_gen_codec().
Several properties are optional and depend on whether the codec itself
supports certain features and behaviors.
The goal of this interface is to handle all of the properties defined
in the SoundWire Discovery and Configuration Specification Version
1.0 so that controller and codec drivers do not need to all have code
for writing standard properties.
Both of these functions also provide a callback method for adding
custom properties that are not defined by the SoundWire DisCo
Specification. These properties may be required by OS drivers but are
outside of the scope of the SoundWire specification itself.
This code is tested with controller, codec, and mainboard
implementations in subsequent commits.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ib185eaacf3c4914087497ed65479a772c155502b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This header implements structures to describe the properties defined in
the SoundWire Discovery and Configuration Specification Version 1.0.
By itself this just provides the property definitions, it is then used
by the code that generates ACPI device properties and by the controller
and codec drivers.
A new header for MIPI vendor/device IDs is also added, with the MIPI
Alliance board members added by default. This will be used in the same
way as pci_ids.h to track devices added to coreboot.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ie9901d26d1efe68edad7c049c98a976c4e4f06f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 44ae0eacb8.
Reason for revert: Resource allocator patches need to be reverted
until the AMD chipsets can be fixed to handle the resource allocation
flow correctly.
BUG=b:149186922
Change-Id: I90f3eac2d23b5f59ab356ae48ed94d14c7405774
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41412
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds some spd_cache functions. They are for implementing the
spd_cache. It's for reducing the SPD fetch time when device uses SODIMMs.
The MRC cache also includes SPD data, but there is no public header file
available to decode the struct of MRC. So SPD cache is another solution.
BUG=b:146457985
BRANCH=None
TEST=Build puff successfully and verified below two items.
one DIMM save the boot time : 158ms
two DIMM save the boot time : 265ms
Change-Id: Ia48aa022fabf8949960a50597185c9d821399522
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This patch adds the get_spd_sn function. It's for reading SODIMM serial
number. In spd_cache implementation it can use to get serial number
before reading whole SPD by smbus.
BUG=b:146457985
BRANCH=None
TEST=Wrote sample code to get the serial number and ran on puff.
It can get the serial number correctly.
Change-Id: I406bba7cc56debbd9851d430f069e4fb96ec937c
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40414
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:41194 got rid of "this file is part of" lines. However, there are
some changes that landed right around the same time including those
lines. This change uses the following command to drop the lines from
new files:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic3c1d717416f6b7e946f84748e2b260552c06a1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41342
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Picasso has an LPC and eSPI bridge on the same PCI DEVFN. They can both
be active at the same time. This adds a way to specify which devices
belong on which bus.
i.e.,
device pci 14.3 on # - D14F3 bridge
device espi 0 on
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device lpc 0 on
end
end
BUG=b:154445472
TEST=Built trembyle and saw static.c contained the espi bus.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0c2f40813c05680f72e5f30cbb13617e8f994841
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add functionality to use process call cycle. It can be used to
write/read data to/from e.g. EEPROM attached to SMBus Controller
via I2C.
Tested on:
* C246
Change-Id: Ifdac6cf70a4ce744601f5d152a83d2125ea88360
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39875
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
pci_domain_set_resources is duplicated in all the SOCs. This change
promotes the duplicated function.
Picasso was adding it again in the northbridge patch. I decided to
promote the function instead of duplicating it.
BUG=b:147042464
TEST=Build and boot trembyle.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iba9661ac2c3a1803783d5aa32404143c9144aea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds helper functions that can be used to check support
for different slave capabilities.
BUG=b:153675913
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic66b06f9efcafd0eda4c6029fa67489de76bbed4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change adds support for allocating resources above the 4G
boundary by making use of memranges for resource windows enabled in
the previous CL.
It adds a new resource flag IORESOURCE_ABOVE_4G which is used in the
following ways:
a) Downstream device resources can set this flag to indicate that they
would like to have their resource allocation above the 4G
boundary. These semantics will have to be enabled in the drivers
managing the devices. It can also be extended to be enabled via
devicetree. This flag is automatically propagated by the resource
allocator from downstream devices to the upstream bridges in pass
1. It is done to ensure that the resource allocator has a global view
of downstream requirements during pass 2 at domain level.
b) Bridges have a single resource window for each of mem and prefmem
resource types. Thus, if any downstream resource of the bridge
requests allocation above 4G boundary, all the other downstream
resources of the same type under the bridge will be allocated above 4G
boundary.
c) During pass 2, resource allocator at domain level splits
IORESOURCE_MEM into two different memory ranges -- one for the window
below 4G and other above 4G. Resource allocation happens separately
for each of these windows.
d) At the bridge level, there is no extra logic required since the
resource will live entirely above or below the 4G boundary. Hence, all
downstream devices of any bridge will fall within the window allocated
to the bridge resource. To handle this case separately from that of
domain, initializing of memranges for a bridge is done differently
than the domain.
Limitation:
Resources of a given type at the bridge or downstream devices
cannot live both above and below 4G boundary. Thus, if a bridge has
some downstream resources requesting allocation for a given type above
4G boundary and other resources of the same type requesting allocation
below 4G boundary, then all these resources of the same type get
allocated above 4G boundary.
BUG=b:149186922
TEST=Verified that resources get allocated above the 4G boundary
correctly on volteer.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7fb2a75cc280a307300d29ddabaebfc49175548f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the comment for memranges_next_entry() to indicate
that the limit provided by the caller is inclusive.
Change-Id: Id40263efcb9417ed31c130996e56c30dbbc82e02
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This replaces GPLv2-or-later and GPLv2-only long form text with the
short SPDX identifiers.
Commands used:
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Also split "this is part of" line from copyright notices.
Change-Id: Ibc2446410bcb3104ead458b40a9ce7819c61a8eb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
That makes it easier to identify "license only" headers (because they
are now license only)
Script line used for that:
perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist...
Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Now that all ACPI header files are moved to src/include/acpi, this
change updates the #ifdef to __ACPI_${FILENAME}__.
BUG=b:155428745
Change-Id: Id24ee35bac318278871a26f98be7092604de01c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 2/5 which moves the contents of
arch/x86/include/arch/acpi*.h files into include/acpi/acpi*.h and
updates the arch header files to include acpi header files. These are
just temporary placeholders and will be removed later in the series.
BUG=b:155428745
Change-Id: I9acb787770b7f09fd2cbd99cb8d0a6499b9c64b3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This change adds a helper function cpu_get_lapic_addr() that returns
LOCAL_APIC_ADDR for x86. It also adds a weak default implementation
which returns 0 if platform does not support LAPIC. This is being
done in preparation to move all ACPI table support in coreboot out of
arch/x86.
BUG=b:155428745
Change-Id: I4d9c50ee46804164712aaa22be1b434f800871ec
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
smbios_slot_{type,data_width,length,designation} used for smbios_type_9 needs "smbios.h"
Also use already defined 'smbios_type11' in "smbios.h".
This will also include <smbios.h> in "static.c" file, this we can remove indirect includes of
<smbios.h> in "chip.h"
Change-Id: Id412a504da2fd75648636febd150356569e07935
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40310
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for devices with the reset vector pointing into DRAM. This
is a specific implementation that assumes a paradigm of AMD Family 17h
(a.k.a. "Zen"). Until the first ljmpl for protected mode, the core's
state appears to software like other designs, and then the actual
physical addressing becomes recognizable.
These systems cannot implement cache-as-RAM as in more traditional
x86 products. Therefore instead of reusing CAR names and variables,
a substitute called "earlyram" is introduced. This change makes
adjustments to CAR-aware files accordingly.
Enable NO_XIP_EARLY_STAGES. The first stage is already in DRAM, and
running subsequent stages as XIP in the boot device would reduce
performance.
Finally, add a new early_ram.ld linker file. Because all stages run in
DRAM, they can be linked with their .data and .bss as normal, i.e. they
don't need to rely on storage available only at a fixed location like
CAR systems. The primary purpose of the early_ram.ld is to provide
consistent locations for PRERAM_CBMEM_CONSOLE, TIMESTAMP regions, etc.
across stages until cbmem is brought online.
BUG=b:147042464
TEST=Build for trembyle, and boot to ramstage.
$ objdump -h cbfs/fallback/bootblock.debug
Idx ,Name ,Size ,VMA ,LMA ,File off Algn
0 ,.text ,000074d0 ,08076000 ,08076000 ,00001000 2**12
1 ,.data ,00000038 ,0807d4d0 ,0807d4d0 ,000084d0 2**2
2 ,.bss ,00000048 ,0807d508 ,0807d508 ,00008508 2**2
3 ,.stack ,00000800 ,0807daf0 ,0807daf0 ,00000000 2**0
4 ,.persistent ,00001cfa ,0807e2f0 ,0807e2f0 ,00000000 2**0
5 ,.reset ,00000010 ,0807fff0 ,0807fff0 ,0000aff0 2**0
6 ,.debug_info ,0002659c ,00000000 ,00000000 ,0000b000 2**0
7 ,.debug_abbrev ,000074a2 ,00000000 ,00000000 ,0003159c 2**0
8 ,.debug_aranges,00000dd0 ,00000000 ,00000000 ,00038a40 2**3
9 ,.debug_line ,0000ad65 ,00000000 ,00000000 ,00039810 2**0
10 ,.debug_str ,00009655 ,00000000 ,00000000 ,00044575 2**0
11 ,.debug_loc ,0000b7ce ,00000000 ,00000000 ,0004dbca 2**0
12 ,.debug_ranges ,000029c0 ,00000000 ,00000000 ,00059398 2**3
Change-Id: I9c084ff6fdcf7e9154436f038705e8679daea780
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Picasso does not define the state of variable MTRRs on boot. Add a
helper function to clear all MTRRs.
BUG=b:147042464
TEST=Build trembyle
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I21b887ce12849a95ddd8f1698028fb6bbfb4a7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40764
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.acpi_inject_dsdt() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
acpi_inject_dsdt as const.
Change-Id: I3b096d9a5a9d649193e32ea686d5de9f78124997
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40711
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.acpi_fill_ssdt() does not need to modify the device structure. This
change makes the struct device * parameter to acpi_fill_ssdt() as
const.
Change-Id: I110f4c67c3b6671c9ac0a82e02609902a8ee5d5c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40710
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
dev_name() does not need to modify the device structure. Hence, this
change makes the struct device * parameter to dev_name() as const.
Change-Id: I6a94394385e45fd76f68218bf57914bddd2e2121
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40703
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.write_acpi_tables() should not be updating the device structure. This
change makes the struct device * argument to it as const.
Change-Id: I50d013e83a404e0a0e3837ca16fa75c7eaa0e14a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change adds all the missing PCI device IDs for AMD Family
17h. IDs that were already present are updated to include _FAM17H_ in
the name instead of _PCO_ and _DALI_. This ensures that the PCI IDs
match the family and models as per the PPR. In cases where the
controller is present only on certain models, _MODEL##H_ is also
included in the name.
BUG=b:153858769
BRANCH=None
TEST=Verified that trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ia767d32ec22f5e58827e7531c0d3d3bac90d3425
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
IOMMU for AMD Family 17h Model 10-20h uses the same PCI device ID
0x15D1. This change updates the name to indicate that the PCI device
ID is supported for FP5(Model 18h) and FT5(Model 20h).
BUG=b:153858769
BRANCH=None
TEST=Trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I17c782000ed525075a3e438ed820a22d9af61a26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Allow to write protect only the WP_RO region in case of enabled VBOOT.
One can either lock the boot device in VERSTAGE early if VBOOT is enabled,
or late in RAMSTAGE. Both options have their downsides as explained below.
Lock early if you don't trust the code that's stored in the writeable
flash partition. This prevents write-protecting the MRC cache, which
is written in ramstage. In case the contents of the MRC cache are
corrupted this can lead to system instability or trigger unwanted code
flows inside the firmware.
Lock late if you trust the code that's stored in the writeable
flash partition. This allows write-protecting the MRC cache, but
if a vulnerability is found in the code of the writeable partition
an attacker might be able to overwrite the whole flash as it hasn't
been locked yet.
Change-Id: I72c3e1a0720514b9b85b0433944ab5fb7109b2a2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Introduce boot media protection settings and use the existing
boot_device_wp_region() function to apply settings on all
platforms that supports it yet.
Also remove the Intel southbridge code, which is now obsolete.
Every platform locks the SPIBAR in a different stage.
For align up with the common mrc cache driver and lock after it has been
written to.
Tested on Supermicro X11SSH-TF. The whole address space is write-protected.
Change-Id: Iceb3ecf0bde5cec562bc62d1d5c79da35305d183
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Instead of only using magic values add enums and defines to allow
writing the codec init sequence in human readable form.
This will replace the magic numbers in mainboards HDA verb tables.
Change-Id: Icad07c2b550657b879ad9328a70ba44629a0c939
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When CONFIG_SEPARATE_VERSTAGE=n, all verstage code gets linked into the
appropriate calling stage (bootblock or romstage). This means that
ENV_VERSTAGE is actually 0, and instead ENV_BOOTBLOCK or ENV_ROMSTAGE
are 1. This keeps tripping up people who are just trying to write a
simple "are we in verstage (i.e. wherever the vboot init logic runs)"
check, e.g. for TPM init functions which may run in "verstage" or
ramstage depending on whether vboot is enabled. Those checks will not
work as intended for CONFIG_SEPARATE_VERSTAGE=n.
This patch renames ENV_VERSTAGE to ENV_SEPARATE_VERSTAGE to try to
clarify that this macro can really only be used to check whether code is
running in a *separate* verstage, and clue people in that they may need
to cover the linked-in verstage case as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2ff3a3c3513b3db44b3cff3d93398330cd3632ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds a helper function dev_find_matching_device_on_bus()
which scans all the child devices on the given bus and calls a
match function provided by the caller. It returns the first device
that the match function returns true for, else NULL if no such device
is found.
Change-Id: I2e3332c0a175ab995c523f078f29a9f498f17931
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40543
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For bit fields with 31 bits (e.g: DEFINE_BITFIELD(MYREG, 30, 0) ),
the calculation of mask value will go overflow:
"error: integer overflow in expression '-2147483648 - 1' of
type 'int' results in '2147483647'".
And for bit fields with 32 bits (e.g: DEFINE_BITFIELD(MYREG, 31, 0) ),
the error will be:
"error: left shift count >= width of type [-Werror=shift-count-overflow]"
To fix these issues, the bit field macros should always use unsigned
integers, and use 64bit integer when creating mask value.
Change-Id: Ie3cddf9df60b83de4e21243bfde6b79729fb06ef
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add C621A, C627A and C629A SKU IDs. C621A is used in the Whitley Product.
We need to add device ID for setting LPC resources.
Refer to Intel C620 series PCH EDS (547817).
Change-Id: I19a4024808d5aa72a9e7bd434613b5e7c9284db8
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40395
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add header file from keycodes from Linux sources. This is needed so
that coreboot can provide scancode to keycode mappings in the ACPI
that the linux kernel expects (https://lkml.org/lkml/2020/3/24/588)
Signed-off-by: Rajat Jain <rajatja@google.com>
Change-Id: I40051cb63a6c154728887ac9b0521bc671b2a518
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40029
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a definition for a software SMI to allow AMD systems supporting
the MboxBiosCmdSmmInfo command to properly initialize the PSP.
BUG=b:153677737
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I1d78aabb75cb76178a3606777d6a11f1e8806d9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40294
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`.read_resources` and `.set_resources` are the only two device
operations that are considered mandatory. Other function pointers
can be left NULL. Having dedicated no-op implementations for the
two mandatory fields should stop the leaking of no-op pointers to
other fields.
Change-Id: I6469a7568dc24317c95e238749d878e798b0a362
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40207
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It turns out the linker's error message already includes the line
number of the dead_code() invocation. If we don't include the line
number in the identifier for our undefined reference, we don't need
individual identifiers at all and can work with a single, global
declaration.
Change-Id: Ib63868ce3114c3f839867a3bfb1b03bdb6facf16
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I2fa3bad88bb5b068baa1cfc6bbcddaabb09da1c5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
When dead_code() is used in inline functions in a header file, the
generated function names (based on the line number) may collide with
a dead_code() in the code file. Now that we are hit by such a case,
we need a quick solution: Add a tag argument for all invocations in
header files.
Change-Id: I0c548ce998cf8e28ae9f76b5c0ea5630b4e91ae2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These two identifiers were always very confusing. We're not filling and
injecting generators. We are filling SSDTs and injecting into the DSDT.
So drop the `_generator` suffix. Hopefully, this also makes ACPI look a
little less scary.
Change-Id: I6f0e79632c9c855f38fe24c0186388a25990c44d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: David Guckian
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After measured boot is decoupled from verified boot in CB:35077,
vboot_platform_is_resuming() is never vboot-specific, thus it is
renamed to platform_is_resuming() and declared in bootmode.h.
Change-Id: I29b5b88af0576c34c10cfbd99659a5cdc0c75842
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This change updates the align attribute of memranges to be represented
as log2 of the required alignment. This makes it consistent with how
alignment is stored in struct resource as well.
Additionally, since memranges only allow power of 2 alignments, this
change allows getting rid of checks at runtime and hence failure cases
for non-power of 2 alignments.
This change also updates the type of align to be unsigned char.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie4d3868cdff55b2c7908b9b3ccd5f30a5288e62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
AMD's Family 17h SoCs share the same video device ID, but may need
different video BIOSes. This adds the common code changes to check the
vendor & device IDs along with the revision and select the correct video
BIOS to use.
Change-Id: I2978a5693c904ddb09d23715cb309c4a356e0370
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2040455
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Matt Papageorge <matt.papageorge@amd.corp-partner.google.com>
Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
AMD's Family 17h SOCs have the same vendor and device IDs for
their graphics blocks, but need different video BIOSes. The
only difference is the revision number.
Add a Kconfig option that allows us to add the revision number
of the graphics device to the PCI option rom saved in CBFS.
Because searching CBFS takes a non-trivial amount of time,
only enable the option if it's needed. If it's not used, or
if nothing matches, the check will fall through and search for
an option rom with no version.
BUG=b:145817712
TEST=With surrounding patches, loads dali vbios
Change-Id: Icb610a2abe7fcd0f4dc3716382b9853551240a7a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2013181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch replaces hard-coded PCI IDs with macros from pci_ids.h and
adds the related IDs to it.
The resulting binary doesn't differ from the one without this patch.
Used documents:
- Intel 322170
Change-Id: I3326f142d483f5008fb2ac878f30c1a3a72f500f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I89b10076e0f4a4b3acd59160fb7abe349b228321
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tiger Lake Thunderbolt(TBT) has 4 PCIe root ports. Add those TBT
root port devices Id from EDS #575683.
BUG=None
TEST=built image and booted to kernel successfully.
Change-Id: Ia117d63daa15dfb21db28fd76723e97ab030da92
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39526
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper function memranges_is_empty() which returns
true if there are no entries in memranges.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: If841c42a9722cbc73ef321568928bc175bf88fd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change adds memranges_steal() which allows the user
to steal memory from the list of available ranges by providing a set
of constraints (limit, size, alignment, tag). It tries to find the
first big enough range that can satisfy the constraints, creates a
hole as per the request and returns base of the stolen memory.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ibe9cfae18fc6101ab2e7e27233e45324c8117708
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change enables memranges library to support addresses with
different alignments. Before this change, memranges library supported
aligning addresses to 4KiB only. Though this works for most cases, it
might not be the right alignment for every use case. Example: There
are some resource allocator changes coming up that require a different
alignment when handling the range list.
This change adds a align parameter to struct memranges that determines
the alignment of all range lists in that memrange. In order to
continue supporting current users of memranges, default alignment is
maintained as 4KiB.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I1da0743ff89da734c9a0972e3c56d9f512b3d1e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BRANCH=none
BUG=b:145946347
TEST==boot to OS with TGL RVP UP3
Signed-off-by: Hu, Hebo <hebo.hu@intel.com>
Signed-off-by: li feng <li1.feng@intel.com>
Change-Id: I3a4f73e82f62def3adb2cb1332a315366078c918
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39478
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code in coreboot is actually for the Arrandale processors, which
are a MCM (Multi-Chip Module) with two different dies:
- Hillel: 32nm Westmere dual-core CPU
- Ironlake: 45nm northbridge with integrated graphics
This has nothing to do with the older, single-die Nehalem processors.
Therefore, replace the references to Nehalem with the correct names.
Change-Id: I8c10a2618c519d2411211b9b8f66d24f0018f908
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38942
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This option is not used on any platform and is not user-visible. It
seems that it has not been used by anyone for a long time (maybe ever).
Let's get rid of it to make future CBFS / program loader development
simpler.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2fa4d6d6f7c1d7a5ba552177b45e890b70008f36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
cbfs_boot_load_stage_by_name() and cbfs_prog_stage_section() are no
longer used. Remove them to make refactoring the rest of the CBFS API
easier.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie44a9507c4a03499b06cdf82d9bf9c02a8292d5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
To mitigate against sinkhole in software which is required on
pre-sandybridge hardware, the smm entry point needs to check if the
LAPIC base is between smbase and smbase + smmsize. The size needs to
be available early so add them to the relocatable module parameters.
When the smmstub is used to relocate SMM the default SMM size 0x10000
is provided. On the permanent handler the size provided by
get_smm_info() is used.
Change-Id: I0df6e51bcba284350f1c849ef3d012860757544b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch moves the PCI ID definitions to pci_ids.h file
and replaces every occurrence with the new names.
The resulting binary doesn't differ from the one
without this patch.
Used documents:
- Intel 337018
Change-Id: Ib7d2aae78c8877f3c9287d03b20a5620db293445
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
soc//picasso is intended to be forward-compatible with the Dali APU, a
Family 17h Models 20h-2Fh product. Add the one new device ID it has.
See PPR document #55772 (still NDA only) for more information.
Change-Id: I7e9b90bb00ae6f4a121f10b1467d2ca398ac860c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Check to ensure that dual monitor mode is supported on the
current processor. Dual monitor mode is normally supported on
any Intel x86 processor that has VTx support. The STM is
a hypervisor that executes in SMM dual monitor mode. This
check should fail only in the rare case were dual monitor mode
is disabled. If the check fails, then the STM will not
be initialized by coreboot.
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Change-Id: I518bb2aa1bdec94b5b6d5e991d7575257f3dc6e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Serves two purposes:
(1) On some platforms, FSP initialization may cause a reboot.
Push clearing the recovery mode switch until after FSP code runs,
so that a manual recovery request (three-finger salute) will
function correctly under this condition.
(2) The recovery mode switch value is needed at BS_WRITE_TABLES
for adding an event to elog. (Previously this was done by
stashing the value in CBMEM_ID_EC_HOSTEVENT.)
BUG=b:124141368, b:35576380
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I30c02787c620b937e5a50a5ed94ac906e3112dad
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This CL has changes that allow us to enable a configurable
ramstage, and one change that allows us to minimize PCI
scanning. Minimal scanning is a frequently requested feature.
To enable it, we add two new variables to src/Kconfig
CONFIGURABLE_RAMSTAGE
is the overall variable controlling other options for minimizing the
ramstage.
MINIMAL_PCI_SCANNING is how we indicate we wish to enable minimal
PCI scanning.
Some devices must be scanned in all cases, such as 0:0.0.
To indicate which devices we must scan, we add a new mandatory
keyword to sconfig
It is used in place of on, off, or hidden, and indicates
a device is enabled and mandatory. Mandatory
devices are always scanned. When MINIMAL_PCI_SCANNING is enabled,
ONLY mandatory devices are scanned.
We further add support in src/device/pci_device.c to manage
both MINIMAL_PCI_SCANNING and mandatory devices.
Finally, to show how this works in practice, we add mandatory
keywords to 3 devices on the qemu-q35.
TEST=
1. This is tested and working on the qemu-q35 target.
2. On CML-Hatch
Before CL:
Total Boot time: ~685ms
After CL:
Total Boot time: ~615ms
Change-Id: I2073d9f8e9297c2b02530821ebb634ea2a5c758e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
This update is a combination of all four of the patches so that the
commit can be done without breaking parts of coreboot. This possible
breakage is because of the cross-dependencies between the original
separate patches would cause failure because of data structure changes.
security/intel/stm
This directory contains the functions that check and move the STM to the
MSEG, create its page tables, and create the BIOS resource list.
The STM page tables is a six page region located in the MSEG and are
pointed to by the CR3 Offset field in the MSEG header. The initial
page tables will identity map all memory between 0-4G. The STM starts
in IA32e mode, which requires page tables to exist at startup.
The BIOS resource list defines the resources that the SMI Handler is
allowed to access. This includes the SMM memory area where the SMI
handler resides and other resources such as I/O devices. The STM uses
the BIOS resource list to restrict the SMI handler's accesses.
The BIOS resource list is currently located in the same area as the
SMI handler. This location is shown in the comment section before
smm_load_module in smm_module_loader.c
Note: The files within security/intel/stm come directly from their
Tianocore counterparts. Unnecessary code has been removed and the
remaining code has been converted to meet coreboot coding requirements.
For more information see:
SMI Transfer Monitor (STM) User Guide, Intel Corp.,
August 2015, Rev 1.0, can be found at firmware.intel.com
include/cpu/x86:
Addtions to include/cpu/x86 for STM support.
cpu/x86:
STM Set up - The STM needs to be loaded into the MSEG during BIOS
initialization and the SMM Monitor Control MSR be set to indicate
that an STM is in the system.
cpu/x86/smm:
SMI module loader modifications needed to set up the
SMM descriptors used by the STM during its initialization
Change-Id: If4adcd92c341162630ce1ec357ffcf8a135785ec
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: ron minnich <rminnich@gmail.com>
This change adds support for allocating resources for PCI express hotplug
bridges when PCIEXP_HOTPLUG is selected. By default, this will add 32 PCI
subordinate numbers (buses), 256 MiB of prefetchable memory, 8 MiB of
non-prefetchable memory, and 8 KiB of I/O space to any device with the
PCI_EXP_SLTCAP_HPC bit set in the PCI_EXP_SLTCAP register, which
indicates hot-plugging capability. The resource allocation is configurable,
please see the PCIEXP_HOTPLUG_* variables in src/device/Kconfig.
In order to support the allocation of hotplugged PCI buses, a new field
is added to struct device called hotplug_buses. This is defaulted to
zero, but when set, it adds the hotplug_buses value to the subordinate
value of the PCI bridge. This allows devices to be plugged in and
unplugged after boot.
This code was tested on the System76 Darter Pro (darp6). Before this
change, there are not enough resources allocated to the Thunderbolt
PCI bridge to allow plugging in new devices after boot. This can be
worked around in the Linux kernel by passing a boot param such as:
pci=assign-busses,hpbussize=32,realloc
This change makes it possible to use Thunderbolt hotplugging without
kernel parameters, and attempts to match closely what our motherboard
manufacturer's firmware does by default.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I500191626584b83e6a8ae38417fd324b5e803afc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35946
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The names of each spi flash cause quite a bit of bloat in the text
size of each stage/program. Remove the name entirely from spi flash
in order to reduce overhead. In order to pack space as closely as
possible the previous 32-bit id and mask were split into 2 16-bit
ids and masks.
On Chrome OS build of Aleena there's a savings of >2.21KiB in each
of verstage, romstage, and ramstage.
Change-Id: Ie98f7e1c7d116c5d7b4bf78605f62fee89dee0a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch creates a new commonlib/bsd subdirectory with a similar
purpose to the existing commonlib, with the difference that all files
under this subdirectory shall be licensed under the BSD-3-Clause license
(or compatible permissive license). The goal is to allow more code to be
shared with libpayload in the future.
Initially, I'm going to move a few files there that have already been
BSD-licensed in the existing commonlib. I am also exracting most
contents of the often-needed <commonlib/helpers.h> as long as they have
either been written by me (and are hereby relicensed) or have an
existing equivalent in BSD-licensed libpayload code. I am also
relicensing <commonlib/compression.h> (written by me) and
<commonlib/compiler.h> (same stuff exists in libpayload).
Finally, I am extracting the cb_err error code definitions from
<types.h> into a new BSD-licensed header so that future commonlib/bsd
code can build upon a common set of error values. I am making the
assumption here that the enum constants and the half-sentence fragments
of documentation next to them by themselves do not meet the threshold of
copyrightability.
Change-Id: I316cea70930f131e8e93d4218542ddb5ae4b63a2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add Elkhartlake CPU, SA and PCH IDs.
EHL PCH is code named as MCC.
Also add a MCH ID (JSL_EHL) which is shared by both JSL and EHL SKUs.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I03f15832143bcc3095a3936c65fbc30a95e7f0f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38489
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When vboot was first integrated into CBFS it was still part of Google
vendorcode. So to not directly tie custom vendorcode into the core CBFS
library, the concept of cbfs_locator was introduced to decouple core
code from an arbitrary amount of platform-specific implementations that
want to decide where the CBFS can be found.
Nowadays vboot is a core coreboot feature itself, and the locator
concept isn't used by anything else anymore. This patch simplifies the
code by removing it and just calling vboot from the CBFS library
directly. That should make it easier to more closely integrate vboot
into CBFS in the future.
Change-Id: I7b9112adc7b53aa218c58b8cb5c85982dcc1dbc0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
By grouping the spi flash parts by their {vendor, sector topology}
tuple one can use a common probe function for looking up the part
instead of having per-vendor probe functions. Additionally, by
grouping by the command set one can save more space as well. SST
is the exception that requires after_probe() function to unlock the
parts.
2KiB of savings in each of verstage, romstage, and ramstage
on Aleena Chrome OS Build.
Change-Id: I9cc20ca0f3d0a1b97154b000c95ff2e7e87f3375
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
To further drive to a common approach for describing the spi flash
parts in the drivers add spi_flash_part_id object. All the drivers
are updated to utilize the new object. Additionally, the driver_private
is also not needed in the spi_flash object.
A Chrome OS build of Aleena provides 960 byte saving of text. A subsequent
patch will save more memory.
Change-Id: I9c0cc75f188ac004ab647805b9551bf06a0c646b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Put the write protection into its own object. This allows
for easier future reuse of objects in future consolidation
patches. It's also possible to eliminate the code implmementing
these in the future if the platform doesn't require it. For now
leave current behavior as-is.
The names of the callbacks were shortened as they are now in
the spi_flash_protection_ops object which is a new field in the
spi_flash object.
Change-Id: I2fec4e4430709fcf3e08a55dd36583211c035c08
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This avoids including platform-specific headers with different
filenames from common code.
Change-Id: Idf9893e55949d63f3ceca2249e618d0f81320321
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Both IO port and cmos are currently arch/x86 only features.
Change-Id: I010af3f645c0be38dd856657874c36103aebbdc2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38187
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
