Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
busty workloads like Octane, Aquarium on open yorp board with heat sink,
sometime CPU temperature spikes till 99 degree Celsius and DPTF
initiates system shutdown. With reference to previous APL/reef/coral
platforms, this updates 105 degree Celsius for the CPU critical
temperature trip value to avoid shutdown. This patch also updates power
limit1 value to avoid the abrupt thermal shutdown by DPTF.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Icd786d3c9b5f7c733dac3fd3e22579e2434058a6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We should use active-state power management where possible to reduce
power consumption during normal operation. Enable these options.
Linux does not seem to enable this for AMD, and the Intel code in coreboot
does enable these options.
PCIEXP_COMMON_CLOCK is enabled also, to follow how Intel does it.
BUG=b:110041917
TEST=boot on grunt, see that WiFi and eMMC still run OK
Change-Id: Ia7c711304ffe460a9fb0d4f654a51485958239ea
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27464
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This creates a meep variant for octopus.
The devicetree overrides are copied from yorp, otherwise everything
just defaults to baseboard settings.
BUG=b:111543000
TEST=None
Change-Id: I791f8d1589d7323fbe884dddf0f9d7362a41b9ac
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Extracted from live running Thinkpad X201 with vendor firmware.
Change-Id: Ia33b4c1a2af6f7d460375cc8ea4e404963a72244
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Extracted from the stock UEFI using UEFItool & intelvbttool.
Without it, the kernel complains about the missing VBT table.
Additionally, the invalid oprom signature warning given by i915
is also gone.
Change-Id: I1871eca9e9c21531d842289f6624ec44420d9844
Signed-off-by: Pablo Moyano <42.pablo.ms@gmail.com>
Reviewed-on: https://review.coreboot.org/27482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Keep the backlight off until it is needed.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen, not prior.
Change-Id: Ia1aba787734e2976146ecd305dd821f0b326f0db
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable the backlight in the OS callback to SMI for APMC. This keeps
the backlight off until the OS is ready to display something.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen
Change-Id: Idf32b1a3d45971883571a829a5c0c1f8563bb1f7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the mainboard resume function and __weak variant override.
Change-Id: I808734208bd1ce81428771ea203709b53db56cd3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This updates the IDPROM region along with the unused regions.
Change-Id: If73bb8162d3d0733e3bd8561cd5549f2184db2be
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/27505
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the EC under the LPC PCI device to make sure that the SSDT path
matches the DSDT. Matches the behaviour of all other Lenovo devices.
Change-Id: I9ded7f639866d71d39ea0d5d0c36602d386c177f
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Matthias Gazzari <mail@qtux.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
there are 3 thermal sensors and index is:
0: 1 Charger
1: 1 SOC
2: 0 CPU
it needs to adjust sensor to index 2 to have correct
CPU temperature.
BUG=b:111284412
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I27afb6c5b64b0c39d6db15e6c61ea16a1fda1ca3
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This device claims to run at 75MHz with dual read, but it is not always
reliable. Add an option to change the SPI flash speed to 16MHz, to avoid
any problems.
BUG=b:111363976
TEST=manually try to get my em100 running (it doesn't yet)
Change-Id: I78d3d32c467aac82c72d31c773bfb0f69808aed4
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This applied to AMD devices as well as Intel, although the mechanism is
different. Move the option to a common place.
BUG=b:111363976
TEST=USE=em100-mode emerge-reef coreboot
See that a message appears:
* Enabling em100 mode (slow SPI flash)
Change-Id: Iea437bdf42e7bc49b1d28c812bfc6128e3eb68bd
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Currently thermal event support can not be disabled at board level.
Define and dependent code are placed in same file.
Move define of HAVE_THERM_EVENT_HANDLER to mainboard file.
Change-Id: Icb532e5bc7fd171ee2921f9a4b9b2150ba9f05c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27415
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling of TBMC device on AP side requires corresponding support on the
EC side as well. Since not all octopus variants have tablet mode support
enabled, this change enables TBMC device only for phaser.
BUG=b:111264961
Change-Id: I1ce181baa8ebaff0a9d767e97ddc256eef9789e8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to get better performance, map dram as cached after dram ready
in romstage.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui. Need a futher check after dram
calibration code ready.
Change-Id: Ie541fe08ee1d5b260abbabc0a5c18fb04e602b9c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27304
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor MMU operation code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Id8173da0a02e57e863263fcd89c91a9c089e8a0f
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add an extra space after 8th value on each line to make it easier
to count the values.
Update the empty spd to remove two random 0x80 values.
BUG=None
TEST=None
Change-Id: If330dbf0c133f65aedddc58ecb351a80b0e45a05
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27423
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set cntfrq_el0 to provide correct timer frequency.
Change-Id: I4b6d0b0cf646a066fc5a51552a1891eccbd91e5e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25450
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Print some useful information about the board.
Change-Id: I0acac7a29290bc2eb9f4283317165fa0cf1b24e1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25449
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Configure and enable MMU.
* Cover the whole I/O space.
* A minimum of 512KB TTB space is required.
* Use secure mem attribute as firmware is running in ARM TZ region.
Tested on Cavium SoC.
Change-Id: I969446da62b4cc7adf9393fab69ff84ebf49220d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This adds Cavium CN81xx SoC and SFF EVB files.
Code is based off of Cavium's Octeon-TX SDK:
https://github.com/Cavium-Open-Source-Distributions/OCTEON-TX-SDK
BDK coreboot differences:
bootblock:
- Get rid of BDK header
- Add Kconfig for link address
- Move CAR setup code into assembly
- Move unaligned memory access enable into assembly
- Implement custom bootblock entry function
- Add CLIB and CSIB blobs
romstage:
- Use minimal DRAM init only
devicetree:
- Convert FTD to static C file containing key value pairs
Tested on CN81xx:
- Boots to payload
- Tested with GNU/Linux 4.16.3
- All hardware is usable (after applying additional commits)
Implemented in future commits:
- Vboot integration
- MMU suuport
- L2 Cache handling
- ATF from external repo
- Devicetree patching
- Extended DRAM testing
- UART init
Not working:
- Booting a payload
- Booting upstream ATF
TODO:
- Configuration straps
Change-Id: I47b4412d29203b45aee49bfa026c1d86ef7ce688
Signed-off-by: David Hendricks <dhendricks@fb.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/23037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
These two files were added before I was able to get the updated linter
committed. Updated/Add the headers so the stable header lint check
can be updated.
Change-Id: I464ddecb5eebe8c5b907f3dcfeab1b06501af6ab
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Clean up leftovers of old SPD generation and utilize
common procedure to produce SPD binary.
Change-Id: I4e48817c03b4372887bc0ea14209736ae2b4e48f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the
keyboard in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
Change-Id: I9af48e648231c18f98d0cc1ddd178b8d00082b0a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To uniform the naming of the 'Dual Graphics' mode amongst the ThinkPads that
support it, the T400 CMOS value needs a change. This was the outcome of a
discussion on another patch: https://review.coreboot.org/#/c/coreboot/+/23040/
This might cause breakage for automated NVRAM configuration scripts, and
manuals. I only found one manual using the previous 'Switchable' option:
https://libreboot.org/docs/install/r400_external.html#a-note-about-gpus
Change-Id: I2e4d8bafbae5de97c78dab118f75fdefff1d7c37
Signed-off-by: Nico Rikken <nico@nicorikken.eu>
Reviewed-on: https://review.coreboot.org/27158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to sona thermal table, PL2 need to check cpu id.
And then set PL2 value.
BUG=b:110867809
TEST=The thermal team verify OK
Change-Id: I5759fb3c685e3d4eef1be054541f950843d19874
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Both southbridges need to be done at once since this southbridge code
is used for different northbridges, which fails to compile when done
separately.
This needs an acpi_name functions in the northbridge code to be
defined.
TESTED on Intel DG43GT: show correct PIRQ ACPI entries in
/sys/firmware/acpi/tables/SSDT.
Change-Id: I286d251ddf8fcae27dd07011a1cd62d8f4847683
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
For this to work the northbridge and lpc bridge device need acpi_name
functions.
TESTED on Thinkpad X200, a valid PIRQ routing in SSDT in
/sys/firmware/acpi/tables/SSDT
Change-Id: I62e520f53fa3f928a8e6f3b3cf33af2acdd53ed9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This commit changes the uid and desc fields for the sx9310 entries
in the devicetree to be unique, and correctly identify the position
of the respective sensors.
Change-Id: I501df7d3349fdebc9673c9815f5b1b2458abac6e
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
We would use GPP_B20 instead of board id to determine nautilus SKU.
BUG=b:80052672
BRANCH=poppy
TEST=Verified the new coreboot could determine SKU correctly
Change-Id: I1978b544eef7a184a3da191306ee32d862fa8c36
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27220
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TPM config items added upstream before ready
SPI/TPM is not functional on Cheza yet
Change-Id: I302e00014dc31279fe2574765763ecdbf326b449
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/27213
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds Open Cellular rotundu mainboard supports.
Working:
- 2x Ethernet support
- MSATA support
- CPU init
- Memory init
- USB support
- EMMC but disabled
Not working:
- TPM support
Create directory structure and Kconfig files for OpenCellular
Rotundu and copy sources from intel/minnowmax.
Change-Id: I391d4bdd485f4bf5396c764fe3f11d98369593e4
Signed-off-by: Hong Gan <hgan@fb.com>
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/22894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This adds another camelbackmountain_fsp derivative, along with a .fmd
file for the board. For now it's been tested to build and boot.
Change-Id: I9e8804264967c19f6b51fc44575b0db36f600f88
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/25884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Put the PCIe clock pins in power-saving mode for the BayHub eMMC bridge to
save power. This requires use of an additional register (Misc control
register 2) and another bit in the existing 'protect' register. The naming
of bit 0 of that register is incorrect, based on the latest datasheet
(14 June 2018) so fix that too.
BUG=b:73726008
BRANCH=none
TEST=boot without this patch:
iotools mem_read32 0xfed80e00
0x0046ffff
With this patch:
$ iotools mem_read32 0xfed80e00
0x00463fff
Also see that the PCIe clock stops when eMMC is idle and can be started by
starting disk activity.
Change-Id: I5ad1467b2e2e151215d2dfd2ce48cd4a451fe480
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/26515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Now that sconfig is able to support variant-specific override trees,
this change updates octopus boards to use this feature. Following
devices are moved from baseboard devicetree to variant specific
devicetree:
1. Touchscreen
2. Trackpad
3. Digitizer
4. Audio codec
BUG=b:80081934
TEST=Verified that the right devices show up in static.c for each
variant.
Change-Id: I8df0cdf4dbcd7613aa4ef4042c272eca2915da9e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27219
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We found GPP_C3 keeps high when system in S0ix mode. It caused 1.8V
leakage. To fix this problem, add GPP_C3 into config for Pantheon
Synaptics touchscreen.
BUG=b:78436458
BRANCH=None
TEST=Let DUT in S0ix mode and check GPP_C3 is normal.
Change-Id: Idb2dab93178af1dae54265e49522b473b69a35af
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Recent patches in coreboot have fixed the freeze issues related to the
use of me_cleaner on Nehalem.
However, at least on the Lenovo X201, with me_cleaner some PCIe devices
(like the SATA and USB controllers) disappear. In particular, setting
the AltMeDisable bit ("-S" or "-s" flag) makes them disappear
completely, while unsetting it makes them disappear only during cold
boots.
This kind of behaviour was already observed by Youness Alaoui on the
Purism Librem laptops ([1]), and it seems related to some required
board-specific PCIe configuration in the ME's MFS partition.
For this reason, on the Lenovo X201, "-w EFFS" has been added to the
me_cleaner arguments, which whitelists the MFS-equivalent partition for
ME generation 2. This fixes all the issues, and the PCIe devices work as
expected.
[1] https://puri.sm/posts/deep-dive-into-intel-me-disablement/
Change-Id: Ie77a80d2cb4945cf1c984bdb0fb1cc2f18e82ebc
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/27178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested with GRUB 2.02 as a payload, booting Arch Linux as
well as Debian. This code is based on the output of autoport
as well as other mainboards supported in coreboot already.
Working:
- Serial port I/O
- S3 suspend/resume. Untested with SeaBIOS since it failed
to resume on a similar board. It is likely to be due to
low memory corruption, but I have not worked on it.
- USB ports and headers
- USB3 ports attached to the ASM1042 controller. SeaBIOS can
boot from them, and it is likely GRUB can detect devices on
those ports as well. The chip has a small SPI flash nearby,
which seems to hold an Option ROM.
- Gigabit Ethernet
- Integrated graphics (libgfxinit)
- VGA BIOS for integrated graphics init
- PCIe x16 graphics
- PCIe x1
- SATA controller
- Hardware Monitor
- Fan Control (fancontrol on linux works well)
- Native raminit
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware.
- NVRAM settings. Only debug_level has been tested.
Untested:
- DVI port. It can detect a "fake" display, that is, an
EEPROM connected to the DVI port. Thus, gma-mainboard.ads
has been setup accordingly.
- PS/2 port.
- Audio: Only rear output (green) has been tested.
- EHCI debug.
- Parallel port header.
- Non-Linux OSes
- ACPI thermal zone and fan control (probably not working)
Not working:
- Booting from devices attached to the ASM1061 controller.
Devices on ports work fine once Linux has loaded.
- Any SATA devices with Tianocore (payload issue)
Change-Id: I7e89ebe43a2e1ff0308f4876e98bbf2f5a0d85f2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/26419
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This configures a GPIO pin for enabling/disabling bluetooth on the
next version of the atlas board. The default is for bluetooth to be
enabled at this point.
BUG=b:110614620,b:110613353
BRANCH=none
TEST=none
Change-Id: I4ba940e89b1dc03548b7ab44b8f84dc9a3097acb
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move GBB_FLAG_DISABLE_EC_SOFTWARE_SYNC under each variant config and
select it for bip and fleex only.
Functional change in this CL is that EC SW sync will be enabled for
phaser.
BUG=b:110523400
Change-Id: If6f37c6b2ee71130b9ed5b10ce92fb23fa1c39fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
SoC users from IOTG team is looking forward for a solution to skip
coreboot AP initialization flow and make use of FSPS-UPD to
perform AP reset.
TEST=Assign use_fsp_mp_init=1 to ensure coreboot is not bringing APs
out of reset.
Change-Id: Ibc8cd411e802fb682436a933073922b2693ba994
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the end it does not look like RCBA register offsets are fully
compatible over southbridges.
This reverts commit d2d2aef6a3.
Is squashed with revert of "sb/intel/common: Fix conflicting OIC
register definition" 8aaa00401b.
Change-Id: Icbf4db8590e60573c8c11385835e0231cf8d63e6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Adds the CMOS option for Dual Graphics, as is present in more Lenovo models
already. Enabling this option ensures that the NVIDIA GPU is powered.
More PCI devices can be observed when activating this setting. It was verified
on a W520, also by loading a VGA option ROM and achieving a working Dual
Graphics system.
The CMOS default has been kept to 'Integrated Only', as the usage of Dual
Graphics requires an option ROM and drains the battery more quickly.
Change-Id: I41ccabd4554ca019684edd6f8b1c23679212c59f
Signed-off-by: Nico Rikken <nico@nicorikken.eu>
Reviewed-on: https://review.coreboot.org/26114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
When played Left Only Audio and Right Only Audio, we observed that Audio
got swapped. Left Data played on Right Speaker and Viceversa.
This patch fixes the above issue.
BUG=b:73635449
TEST=Play Left only & Right only Audio and cross check Audio.
Change-Id: Ie9c417ad0634a76fc8a4126ee75886603f1b3da0
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27167
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set register speed_shift_enable=0 in devicetree to disable
p-states in coreboot as a temporary workaround for an SoC hang.
BUG=b:79666828
BRANCH=none
TEST="emerge-nocturne depthcharge coreboot chromeos-bootimage",
flash spi image onto nocturne, boot to kernel and verify device
stays alive and responsive for several minutes without locking up.
Change-Id: I71ed4c80c109b28ffa85d48338ce3a62396d272e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is a temporary hack to test camera presence before we have full
camera support implemented. Basically, we can now probe the camera
over i2c to verify that it's connected and the camera LED turns on.
BUG=b:80106316
BRANCH=none
TEST=camera LED comes on and camera can be probed over i2c.
Change-Id: Ibaabf6c6f6a1dabaddd2fc47c820e090ca5984a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27128
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We plan to use i2c-hid compatible trackpads on atlas, so this switches
the trackpad config to i2c-hid.
BUG=b:80662079
BRANCH=none
TEST=used trackpad to verify motion tracking
Change-Id: I2702e61a6aa96250c0c09ea4bd15d0c671eedadc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27126
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change defines SAR sensor device into devicetree.cb.
Since only LTE sku has SAR sensor, we will use GPP_B20 as a device_present_gpio.
BUG=None
BRANCH=poppy
TEST=Verified SAR sensor device is loaded by driver in Chrome OS
Change-Id: Ib4969e4b82d18b1b1a599de8226c2d7d4bda7915
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27149
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Nautilus 2nd SKU has a leakage voltage at GPP_D0 in S5 state. We need to set this to LOW when entering S5 for clear the leakage.
BUG=None
BRANCH=poppy
TEST=Verified the leakage is gone after update coreboot
Change-Id: I054e707b2bc2e63d6f99cd2fd8a57be20615f111
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For supporting new SKU, we need to override GPIO table and device configuration.
The board ID of 2nd SKU of nautilus is started from 9, so we would determine SKU with it.
BUG=b:80052672
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7242f23f47010664cc29ea86a126e63c9dd62ccd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27147
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change fixes the following issues with EC_IN_RW signal:
1. EC_IN_RW is an input signal to the SoC. Configure it accordingly in
GPIO table for baseboard and bip.
2. GPIO_EC_IN_RW is passed in coreboot tables so that payload can
re-sample the GPIO at runtime.
BUG=b:110084012
TEST=Verified that EC_IN_RW signal is read correctly in depthcharge.
Change-Id: I1c5f5b4b914ced98e89a571dc398df5ba1fe8460
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Due to schematic, we need to correct USB OC pin configuration.
- OC0 for Type-C Port 1
- OC1 for Type-C Port 0
- OC2 for Type-A Port
- OC3 to NC
BUG=NONE
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ic71baef646926cc6aadcc5dda7cb14f00e8d3687
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This creates a fleex variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:110085182
TEST=None
Change-Id: Ia8b8bb757f67bea997b7f43489c38cac62f7682d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27105
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Grunt variants should identify as grunt in SMBIOS so that
they're recognized correctly as a unibuild Grunt variant.
BUG=b:110244268
TEST=Careena identifies as grunt
Change-Id: Iaf254149fbec9551d9220018d6d6a0a1be741538
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27117
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This pin does not have a native function for eSPI. Nonetheless if we use
eSPI, it should be configured as a GPIO and kept unconnected to allow
S0ix entry.
Also removed initialization of LPC pins in mainboard code as they are
already initialized in chipset code. The settings fpr LPC pins in
chipset code were updated to those that were previously in mainboard
code and have been validated on LPC flavor of Geminilake RVP.
BUG=b:79251613
BRANCH=none
TEST=From kernel prompt in bip, type powerd_dbus_suspend.
Check on EC console that SOC enters S0ix.
Change-Id: Ie0c1013fee638a3b7a91469736efc0c25a1597fa
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23742
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update dptf.asl and TCC parameters from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI
Change-Id: Ic0ffc169ad3939cacb46824ed23999c61a23d2c4
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable keyboard backlight by Careena SKUID
Set to 10% as the same as google/snappy project
BUG=b:110065836
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I7d302c4f50528b0e6b7ef4d990f342a69cff34f5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: I4843f52307b87cff6fa6f4d0c74b87428fefa8ac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
TESTED Intel DG41WV with VGA, Intel DG43GT with VGA and HDMI1 and
HDMI2.
Change-Id: I774b79cc0ef9dc72ccf48901ab94376b27ed9c7a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
GPP_E2 will be used as a BT reset line, so configure GPP_E2 as an
output and initialize it high (high = out of reset).
BUG=b:80089559
BRANCH=none
TEST=none
Change-Id: If45ef3a592c389a0b80298c59eea849d07d9671e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FCAM_PWR_EN signal is changing to connect to GPP_B4 instead of
GPP_D8 as it needs a 3.3v gpio to provide enough power to also
directly power the camera LED.
BUG=b:79667559,b:78122599
BRANCH=none
TEST=none
Change-Id: Ie875ced45dfa2aa7069851004edde8f77329df34
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
After removing most geode_lx boards, some mainboard
directories are left empty. This patch cleans them up.
Change-Id: I2e99eba3d49dec90ceb2ce0c7f61612a9840ce59
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27092
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
BUG=b:80501386
BRANCH=none
TEST=timer and uart work fine
Change-Id: I08644892d34925574f791b000b0035d5afad7022
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/26722
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a result of commit:
[711fb81] soc/intel/skylake: Swap PCI devfn resides in same PCI device
fizz's chip_info for the LAN driver is being overwritten/nulled, as the
LAN device is on function 2 (PCIe port 3), but the driver info was set
for the post-swapped PCIe port (1).
Move the driver chip_info to function 2/port 3, so that it follows the
PCI device function when swapped after FSP-s, and is correctly passed
to the LAN driver.
Test: boot google/fizz (teemo variant), check cbmem console and
verify ethernet MAC address and LED config correctly set.
Change-Id: I08810c0c89d99af5799f42c7c4e51814f09aafec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This code is no longer needed. Removing Kahlee options allows some
Kconfig options to be optimized.
BUG=b:77693343
TEST=Build Grunt, verify that nothing's changed.
Change-Id: I4eeeee7f35381bba8760c8a530251c475d0ee29b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The initial subsystem ID had a device ID but not a vendor ID.
This change adds the Google vendor ID to the subsystem ID.
Change-Id: I14897da115fd6f2ddd492b6c565bd23227197232
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/26987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add tablet motion control config to nami devices.
BUG=None
BRANCH=None
TEST=run evtest
make sure tablet switch value is 1 in tablet mode and 0
when not in tablet mode
Change-Id: Ie1480934dc003d9b467883e001ed89f9a3694d10
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26970
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of device_t has been abandoned in ramstage.
Use pci_devfn_t or pnp_devfn_t instead of device_t in romstage.
Change-Id: Ie0ae3972eacc97ae154dad4fafd171aa1f38683a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26984
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I07e00afbbd2c19cf3ea6e08f228eb39e45f1ad0c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Careena uses a different keyboard backlight method, so let the EC
handle the different SKUs and backlight methods.
BUG=b:80106042
TEST=None
Change-Id: I47f7a9ac13538f0216fbb0f64fdd22f66097820c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Until these need to be separated out, use a common file for mainboard
and romstage to make upkeep easier.
BUG=b:80106042
TEST=Build Grunt and Careena
Change-Id: I65188bee1958d442bfe64637c3b93dc05583a686
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Looking at the 100MHz signal, we were violating the timing requirements.
66MHz still isn't great, but it's a good tradeoff between improving
the signal and losing boot speed time.
This slows down the boot time by about 20mS.
BUG=b:109583457
TEST=Boot grunt, look at signal on scope
Change-Id: I7ce70c992822dd17c5877226e74c1890660768c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Configuring EC_PCH_WAKE_L as an SCI enabled GPIO allows the EC to wake
the AP from S3 on keyboard presses.
BUG=b:109759838
TEST=(1) powerd_dbus_suspend
(2) press a key on the internal keyboard
=> system resumes from S3
Change-Id: I30f72460fd588706f91f4fc3ea4ff007c96e9ebe
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26931
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change b41ae2 (mb/google/octopus: Enable wake-over-wifi for octopus
variants) changed the GPE mappings to accomodate for WiFi wake
pin. However, this resulted in TPM interrupt pin being removed from
the GPIO to GPE mapping. Since we do not support true interrupts in
coreboot, GPE_STS registers are used to identify if an interrupt has
triggered. Change in GPE mapping resulted in this information to be
lost when talking to TPM thus resulting in "Timeout wait for tpm
irq".
This change fixes the above issue by assigning GPIO block for TPM
interrupt back to DW1 and moving GPIO block for wake-over-wifi pin to
DW3. DW3 was mapped to NW_31_0 which only has debug header pins and
CNVI pins (none of them are used for reading GPE_STS or as wake
sources).
BUG=b:109824918
TEST=Verified that there are no "Timeout wait for tpm irq" messages
when talking to TPM.
Change-Id: I30768177a838a684948f7485d760c8b83c3190f7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
TPM over SPI/I2C config selection got changed in
https://review.coreboot.org/c/coreboot/+/24903 so this CL is fixing the
same.
BUG=None
BRANCH=None
TEST=Build for Soraka & make sure that TPM is probed over I2C interface
rather than SPI.
Change-Id: I077e4dc03520e26eb9f6404a7eb1edd99925de77
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26890
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are two cameras on Nami and only one camera on Sona.
We need to disable rear camera/DMIC on all Sona sku.
BUG=b:109710674
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Sona
Change-Id: Id84ee22c9ffc15db78be3bbad148af5cd7dc866e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since there are two cameras on Nami and only one camera on Pantheon.
We need to disable rear camera/DMIC on all Pantheon sku.
BUG=b:109720689
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Pantheon
Change-Id: Ibe48a945dc57f2c05344479253040ad1945d92fd
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Update GPIOs in baseboard to match latest schematics:
1. Get rid of STEST GPIOs(GPIO_{62,84-89})
2. Get rid of SD_CD_ODL(GPIO_134)
3. Get rid of KB control GPIOs(GPIO_{144-146})
4. Configure GPIOs for pen eject (GPIO_{144,145}). Additionally, fix the
configuration for other pen GPIOs.
BUG=b:109764138
Change-Id: I8e40dd90b2784596f055538e57ea67482c4c517a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26874
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds a INTEL_GMA_VBT_HAVE_DATA_FILE Kconfig option for the path
to point to the mainboard dir and to select
INTEL_GMA_ADD_VBT_DATA_FILE by default.
Change-Id: I730cb0737945631e2d5379a9e26b8c039ec6dc49
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/26653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Chip sections must be covered by a PCI device.
Fixes chip_ops not being executed and TPM shows up in OS.
Change-Id: Id0ecd2f2f3e303f2228743369a8025b327bee61d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When the normal termination is None, the standby termination is
none also as per Doc# 572688. So when termination is only needed in
standby, use the IOSSTATE setting that drives low/high via the
Tx mode instead.
Also disabled Speaker in Standby state to save power.
BUG=b:79874891, b:79982669
BRANCH=None
TEST=Compiled and flashed image on Bip. Checked that suspend_resume cycles
pass. Checked that bluetooth is functional on resume. On Yorp, checked
that speaker is functional after a suspend/resume cycle.
Change-Id: I6a3852548f944176a80feb32e9885b03b8af25db
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/26762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Issue observed on the board is: too many jack interrupts.
cat /proc/interrupts | grep da7219
58: 84292 15709 0 0 IO-APIC 58-fasteoi da7219-aad
Updated pad configuration for Jack IRQ pin to fix the issue.
BUG=b:109655907
TEST=Jack insertion & removal detection is working.
Change-Id: I41ef9d40325677b01ca94ec3215e7feded76dcc3
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
During measurement of signals during Elan touchscreen power on, saw
that the enable_gpio delay was not sufficient as there is a +1.5 ms
delay during power on. Adding more delay to take this into account.
BUG=b:78311818
BRANCH=None
TEST=probe power on signals to ensure meet timing requirements
Change-Id: Id661a202188a97aef97514ebecd0be6fc022d21e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Power off does not seem to use the ACPI _OFF function, but rather the
smihandler. Creating variant_smi_sleep function for nami to handle
the power off sequence during reboot/power off.
BUG=b:78311818
BRANCH=None
TEST=Run "poweroff" command from AP console with SMI_DEBUG enabled
Make sure delays are consistent with spec
Change-Id: Ifeea545fe268be249793b3e508c51f5e4c1a3460
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables wake-over-wifi functionality for all octopus
variants by making the following changeS:
1. Configure GPIO_119 as SCI active-low
2. Update GPE0_DW1 to include the group that GPIO_119 falls under
3. Add wake property to wifi device
BUG=b:77224247
TEST=Verified that wake-over-wifi works on yorp.
Change-Id: Ibae199c43e4d96da4c2f68f71a849c2f23d3e7b9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
