Use a GNVS variable to store the trackpad interrupt, in order to
support both SNB and IVB variants from a single build.
Change-Id: I53df35fff41f52a7d142aea9b1b590c65195bcfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
Existing value was copied from librem13 v1 board, use value
obtained from AMI firmware.
TEST: Observe Windows boots correctly, function keys work
under both Windows and Linux.
Change-Id: I0ea6cc4602ce1047cb803acc65cbca1af1f480b0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Update devicetree USB config based on board spec.
Leave OC pins set to skip since the info is unavailable.
Change-Id: I2a4fe17ed7edacbbbaf56969f9d2801b45a20da9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The board dutifully registers an int15h handler and provides the
defaults to add a VGABIOS.
That should be good enough to initialize graphics through the VGABIOS
file.
Fixes build on Chrome OS configurations (at least until the Ada toolchain
situation is resolved over there).
Change-Id: I1d956b5a163b7cdf2bd467197fba95f16e5e8fa3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
As the hardware designed on gru, the AP_I2C_TP_PU_EN (gpio3_b4) controlled
the SCL/SDA status to avoid leakage. And the gpio3_b4 of rk3399 pull
resistor is 26k~71k and 3.3v for supply power, and gpio3_b4 pin connected
2.2k resistor to i2c of TP device.
The default of this gpio status is pulled up during the start to bootup,
it's very weak drive for the TP device that maybe cause to trigger the
recovery process of elan's firmware.
Also, the Elan updated its firmware(102.0.5.0) to delay checking the
i2c of touchpad is greater than 1 second.
So we have to drive the stronger pull-up within 1 second of powering up
the touchpad to prevent its firmware from falling into recovery.
Change-Id: I9a67d1c041afafde24ed9f00716ba41a9b41a8da
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Too low gfx_uma_size can result in problems if the framebuffer
does not fit.
This partially reverts: 7afcfe0 "gm45: enable setting all vram sizes
from cmos"
Change-Id: I485d24198cb784db5d2cfce0a8646e861a4a1695
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
TEST=Verified that board still boots to OS without any error.
Change-Id: I02d2a6cbcab92766a35993bfd20aaeed4ca22c90
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that we dynamically disable TPM interface based on config options,
add support for generation of SPI TPM ACPI node if SPI TPM is used.
Change-Id: I87d28a42b48ba916c70e45a061c5efd91a8a59bf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Based on the config options selected, decide at runtime which TPM
interface should be disabled so that ACPI tables are not generated for
that interface.
TEST=Verified that unused interface does not show up in ACPI tables.
Change-Id: Iee8f49e484ed024c549f60c88d874c08873b75cb
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20141
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
There are many good reasons why we may want to run some sort of generic
callback before we're executing a reset. Unfortunateley, that is really
hard right now: code that wants to reset simply calls the hard_reset()
function (or one of its ill-differentiated cousins) which is directly
implemented by a myriad of different mainboards, northbridges, SoCs,
etc. More recent x86 SoCs have tried to solve the problem in their own
little corner of soc/intel/common, but it's really something that would
benefit all of coreboot.
This patch expands the concept onto all boards: hard_reset() and friends
get implemented in a generic location where they can run hooks before
calling the platform-specific implementation that is now called
do_hard_reset(). The existing Intel reset_prepare() gets generalized as
soc_reset_prepare() (and other hooks for arch, mainboard, etc. can now
easily be added later if necessary). We will also use this central point
to ensure all platforms flush their cache before reset, which is
generally useful for all cases where we're trying to persist information
in RAM across reboots (like the new persistent CBMEM console does).
Also remove cpu_reset() completely since it's not used anywhere and
doesn't seem very useful compared to the others.
Change-Id: I41b89ce4a923102f0748922496e1dd9bce8a610f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19789
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I updated my spike patch[1] to cleanly apply to current spike master.
As a side effect, the UART is now at 0x02100000.
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I4cb09014619e230011486fa57636abe183baa4be
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/20126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for google/rambi
as to not break compilation.
Change-Id: I4ef978214aa36078dc04ee1c73b3e2b4bb22f692
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20056
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Update devicetree PCI config based on board spec:
- enable PCIe Root Ports 5 and 9 (wifi and nvme respectively)
- enable PCIe CLKREQ on RP9, disable on RP5
- enable USB OTG
- enable P2SB
Note: PCIe RP5 is on 0.1c.0 despite this being labeled as RP1
Change-Id: Ia71ed25bd41668df1ee3e4b4e28f54482722452c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The FSP Temp RAM init will fail if the mircocode values are set
to 0. A valid microcode update needs to be included and its size
and offset need to be set in the config.
Change-Id: I26d05bd7b37c8d91bf34f399c7c4189f9d3dd34a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19936
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Adding code to setup the spd information from sodimm.
Adapted from intel/kblrvp.
Change-Id: I0403f999dac1bdef0e9e1abe7c9c62407e223bb1
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The GPIO configuration matches the one from the original BIOS.
Some configs don't make much sense, but I kept it as is so it
would match (such as a NC pin with TX set to 1, or RXINV enabled).
Remove unnecessary early GPIO config.
Change-Id: Iaec8630cef9a523fb2e2503143aa4aa72fbedc1f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19934
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Like other devices using ENE embedded controllers, the librem13v2
requires this config option for the PS2 keyboard and mouse
(trackpad) to function properly.
Change-Id: Ifba13b93a1fe2e76b2790d1c273fd9e2b5368ab0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the initial directory for the port of the Librem 13 v2.
The base implementation was copied from the google/chell directory
and the chell references were replaced. spd directory was removed
since the RAM is not soldered on the MB. The Kconfig, board_info.txt
and devicetree.cb files were modified to match the Librem 13 v2
hardware information. The romstage.c, mainboard.c, Makefile.in and
dsdt.asl were modified to remove chromeos specific code. The boardid.c,
chromeos.c, chromeos.fmd, cmos.layout, ec.c, ec.h and smihandler.c
files were removed from the tree, and the acpi directory was replaced
with the acpi directory from the purism/librem13 board.
These changes allow us to remove the references to chromeos specific
code and allow coreboot to compile when the librem13v2 board is selected.
Change-Id: I24263fde18fcea70163dbdc59df6ea1d98c97af8
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The FADT revision was set to 5, but we do not implement the
ACPI v5.0 specification, which prevents Windows from booting.
Setting it to v3 (matching most other boards) fixes the issue
and Windows now boots normally.
Bug found by Matt DeVillier, fix tested by Youness Alaoui on
Librem 13 v1 hardware.
Please also see commits 00d250e228 (intel/skylake: Switch FADT
to ACPI version 3.0) [1] and 27e6042bb7 (intel/apollolake:
Switch FADT to ACPI version 3.0) [2].
[1] https://review.coreboot.org/19453
[2] https://review.coreboot.org/19146
Change-Id: Ide97cbf64f7b05018433436431ab4723b217fe22
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
A simple rename of the directory and the config values
and string in Kconfig/Kconfig.name/board_info.txt
It will be less confusing for users since the first models
are referred to as 'v1' everywhere now.
Change-Id: I23fa977717230c2001868741bb684e9633a2c0bb
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19931
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for intel/strago
and google/cyan as to not break compilation.
Change-Id: Iaf8211bd86d6261ee8c4d9c4262338f7fe19ef43
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Change-Id: Ie0b64eadc634049f6b65cf555407337fb7c4363c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switch from lapic to tsc.
Allows timestamps to be used in coreboot, as there's a reference
clock available to calculate correct time units.
Clean Kconfig, remove duplicated lapic code and include tsc dir for
LGA1155 boards.
Tested on Lenovo T430.
Change-Id: I849ca2b3908116d9d22907039cd6e4464444b1d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update user facing camera i2c address to 0x36.
BUG=None
TEST=Build & boot on soraka. Make sure user facing camera is detected.
Change-Id: I4645ae5734faef4b6a821c04ab817a7b99da6e4b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide all gfx init methods as a Kconfig `choice`. This elimates the
option to select native gfx init along with running a Video BIOS. It's
been only theoretically useful in one corner case: Hybrid graphics
where only one controller is supported by native gfx init. Though I
suppose in that case it's fair to assume that one would use SeaBIOS to
run the VBIOS.
For the case that we want the payload to initialize graphics or no
pre-boot graphics at all, the new symbol NO_GFX_INIT was added to the
choice. If multiple options are available, the default is chosen as
follows:
* NO_GFX_INIT, if we add a Video BIOS and the payload is SeaBIOS,
* VGA_ROM_RUN, if we add a Video BIOS and the payload is not SeaBIOS,
* NATIVE_VGA_INIT, if we don't add a Video BIOS.
As a side effect, libgfxinit is now an independent choice.
Change-Id: I06bc65ecf3724f299f59888a97219fdbd3d2d08b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The word 'coreboot' should always be written in lowercase, even at the
start of a sentence.
Change-Id: I7945ddb988262e7483da4e623cedf972380e65a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The coreboot sites support HTTPS, and requests over HTTP with SSL are
also redirected. So use the more secure URLs, which also saves a
request most of the times, as nothing needs to be redirected.
Run the command below to replace all occurences.
```
$ git grep -l -E 'http://(www.|review.|)coreboot.org'
| xargs sed -i 's,http://\(.*\)coreboot.org,https://\1coreboot.org,g'
```
Change-Id: If53f8b66f1ac72fb1a38fa392b26eade9963c369
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Wrapping the long line tries to address a warning by `checkpatch.pl`,
but the line is still over 80 characters long.
Change-Id: Ib75d4da1880624eb83f7a419cb6762f1c4c2a7b2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20033
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The comma-separated PCI vendor and device ID is used to associate the
VGA BIOS to the video device by using it as the file name of the VGA
Option ROM.
Change-Id: I755554eeb9a560d034d6e8fe49de619d800ea045
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes the offsets of some options so that options that span multiple
bytes are byte aligned.
To make the cmos.layout file more consistent some things where moved
around in the cmos.layout of thinkpads X200 and T400.
Change-Id: Ic84a2a5dc6f9c102f041085871c2ed55e2f3692a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
A new variant copied from reef.
Allow override of the SKU.
Change-Id: Ibe160e75aa23623812f0fb9121d1d8226afc00d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20020
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each rambi variant has a different USB port config.
Port data currently available for only candy and squawks;
other variants to be added once data obtained.
Change-Id: If7ce3d135d6ffe53ab1566d5258d01b052ac47f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each jecht variant has a different USB port config.
Change-Id: I3b15aac9c4971e2ae230106016fba3a583ec6c9a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each auron variant has a different USB port config.
Change-Id: Id17f21c23540d2e3d5a902a2174b66c7a5a5f3e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since dual-channel setups use same RAM/SPD for both channels,
populate spd_data[1] with same SPD data as spd_data[0],
allowing info for both channels to propogate into the
SBMIOS tables.
Clean up calculations using SPD length to avoid repetition.
Changes modeled after google/auron variants.
Change-Id: I7e14b35642a3fbaecaeb7d1d33b5a7c1405bac45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
No reason to compile/include chromeos.c for non-ChromeOS builds
Change-Id: Ie8ef1f4c521b2a7308941299f2501073937bdf4a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
sata_devslp_disable was set to work around some buggy SSD
firmware, but as it's disabled by default in both Linux and
Windows, no reason to disable at the firmware level when
many properly-functioning SSDs can take advantage of power
savings.
Change-Id: Ib15f8b51db19b3d9d2e135f85c71a15a45a2ffbd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update camera sensor detail to OV 13858
Also update i2c address of OV5670
BUG=None
TEST= Build & boot to ChromeOS. Check for both the camera detection.
Change-Id: I3b6192815201f605d3ebdb4bf54db26a8e837b35
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix for all Sandy-Bridge and Ivy-Bridge devices.
Remove unused option "hyper_threading".
Increase CMOS checksum range to cover all user adjustable settings.
Change-Id: I02f7af13d9c82d7f531d4b49b3bc0e5a20c14b55
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is to align with the SD_CD GpioInt setting in acpi
BUG=b:62067569
TEST=checked unused interrupt on SD_CD does not happen after s3 resume
Change-Id: I40aefcb0f571e7f6773a6d20226f357707aa041a
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/20001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
* Rename it to HAVE_VGA_TEXT_FRAMEBUFFER.
* Let drivers select it if they are in charge.
* Don't select it on the mainboard level if a driver handles it.
Change-Id: I2d9d09be9aa6d019e77460e69a245ad2d8cda4ea
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The separate directory was the old way of handling variant boards.
Update bakersport_fsp to the new method. All of the other pieces
were already moved into bayleybay_fsp.
Change-Id: I5712c1b399570bd7ab7fc9e42af25fbf15a0ba78
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Light sensor isn't used and ACPI already removed, so disable
I2C5 bus interface as well.
Disable I2C6 for devices without a touchscreen
Change-Id: Ib0e041ae9131615ef1140bad064de5aae91f8ee4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Remove MONOTONIC_TIMER_MSR selection from mainboard
Konfigs, as it only does a reduntant selection of
HAVE_MONOTONIC_TIMER config, already selected under
skylake soc Kconfig.
Change-Id: Ib3177ceb9e8b6c16ce0e437a4a02b94f215af58f
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/20002
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
This board is almost identical to D510MO, the only differences are
some differences in populated connections, CPU with less L2 cache and
a 10/100 Realtek NIC.
The vendor uses the very same binary for both D510M0 and D410PT.
Change-Id: I220515365b69e785ef249c4e3a9af5f7fddf02f9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each slippy variant has slightly different USB port config;
data for falco and leon to be added once available
Change-Id: Icc3b5b1161f62ac0b840380679acafeff363cf45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
All beltino variants use the exact same USB port layout.
Change-Id: If5b540949ea071f7165876e12ac1ef50e62d2b22
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Move inclusion of mainboard.asl after southbridge asl files
so scopes referenced in usb.asl are valid.
Change-Id: I58ea0b43f7f2c2692630df3bdb06af92566c1202
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Port 0 is connected to SD-card reader.
Don't mark it as hot-plugable.
Change-Id: I5d3d4c7541683a6c09aac47ca251a6dad23ad1ab
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
To unify the hwinfo handling along all Siemens MC boards the hwinfo
files have to be removed from the mainboard directory. They will be added
to cbfs in site-local/Makefile.inc.
Change-Id: Ia3dcb2e0118527b37aed872740273c4fa7004aef
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The prior used RTC PCF8523 is replaced with RX6110SA on this mainboard.
Switch to the new RTC in Kconfig and adapt devicetree to the new chip.
Change-Id: I7c4911191cae254900f9a958da42ecd18497484c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Modify the DPTF configuration on Eve to relax the severe throttling that
is currently applied and allow performance testing to see better results.
BUG=b:35581264
TEST=performance tests show better results and thermal tests still pass.
Change-Id: I0838f4ec3026bc8bac814698043fa97cf6772cb4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of having the SMI handler power off the touchscreen on the
way into suspend add power resource controls to the ACPI device so
the power is managed by the kernel instead of the BIOS.
BUG=b:35581264
TEST=manual testing on Eve to ensure that the touchscreen is still
functional at boot and after suspend/resume, and that it does not
draw power in suspend.
Change-Id: Id9a98807d24bbc7dff32408f3d113f6fad5bc023
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Tegra210 SoC never had a proper cpu_reset() implementation, so it's
pointless to pretend there is one. Most ARM SoCs/boards only define
hard_reset() at the moment anyway, so let's stick with that.
Change-Id: I40f39921fa99d6dfabf818e7abe7a5732341cf4f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Get rid of mainboard_io_trap_handler.
The only purpose is to enable tp-smapi, but is already done on all
boards in h8_enable, as of devicetree setting config0.
Change-Id: I33fd829a7e34aefa8f76ca6020cc8e802f7aab17
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Instead of assuming the mapping of dimm number to SPD SMBus address,
allow the mainboard to provide its own mapping. That way, global
resources of empty SPD contents aren't wasted in order to address
a dimm on a mainboard that doesn't meet the current assumption.
Change-Id: Id0e79231dc2303373badaae003038a1ac06a5635
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
GPP_C2 is being used as strapping option, so
should not be set to NF. Signal was floating
previously, which can lead to an assertion of
smbalert#.
BUG=b:37681121, b:35775024
BRANCH=None
TEST=powerd_dbus_suspend and ensure stays in suspend
Change-Id: I68091206014621419b886b723a5681541be989bc
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19904
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Do not enable touchscreen device by default in gpio configuration.
2. Select use of PowerResource for touchscreen device in devicetree so
that the ACPI subsystem can take care of powering on/off the
device. When system enters suspend, touchscreen device is powered off
and on resume, it is powered back on.
BUG=b:62028489
TEST=Verified 100 cycles of suspend-resume. Touchscreen still works on
poppy.
Change-Id: Ia0bebc7259b10cc60a9fa5b53542dfdd9685663e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19829
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Should result in a tiny speed bump in raminit since those addresses
are not checked for present DIMMs.
Checked in schematics of both Thinkpad X60 and T60 and tested to
configure raminit correctly for all DIMMs populated on X60.
Change-Id: I56c4f3176541bc75a8de3aac9f87526a77fc819b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Though SPD is rightly selected (i.e., H9CCNNNBKTALBR-NUD),
it displays wrong part number during boot in coreboot logs.
So correct part number info within the SPD.
TEST= Build for Soraka & make sure part number is rightly printed.
Change-Id: I67f676fb6ee9d685fa7aa41fdc4b00355e6d33c7
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19692
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SoC code was never completed. It's just a skeleton that gets
in the way of refactoring other code. Likewise, the mainboard was
never completed either. Just remove them both.
Change-Id: I8faaa9bb1b90ad2936dcdbaf2882651ebba6630c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19823
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Since the conversion of this board to soc/broadwell in 0aa06cbf18
(wtm2: Convert to use soc/intel/broadwell), the NGI for this board
is not hooked up anywhere. Also, the code doesn't compile anymore.
Change-Id: I6387203349b78c8e95333eaf44b345aa30eac7c5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
All those boards do not have a serial port.
Don't attempt to decode the COMA/COMB IO range.
Change-Id: Ide7e818f87e70e3f559d0769ccde89c35da961d6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do not lock ETR3 CF9GR in early romstage.
As of Change-Id: I2cb30267a6342db1f3b11715034219ffb18ca678 this is done
in bd82x6x's finalize handler.
Change-Id: Iea091511f0d2a6128d3a19e9413090c85e4c2e57
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested and working:
* HDD LED
* Booting GNU Linux 4.9 from HDD using SeaBios
* Booting GNU Linux 4.9 from USB using SeaBios
* Native GFX init
* All Fn function keys
* Speakers
* PCIe Wifi
* Camera
* WWAN
* Fan (Dynamic Thermal Managment)
* Flashing using internal programmer
* Dual memory DIMMs running at up to DDR3-1866
* AC events
* Touchpad, trackball and keyboard
* USB3 ports running at SuperSpeed
* Ethernet
* Headphone jack
* Speaker mute
* Microphone mute
* Volume keys
* Fingerprint sensor
* Lid switch
* Thinklight
* TPM (disable SeaBios CONFIG_TCGBIOS)
* CMOS options:
** power_on_after_fail
** reboot_counter
** boot_option
** gfx_uma_size
** usb_always_on
Untested:
* Booting Windows
* Hybrid graphics
* Docking station
* VGA
Broken:
* Wifi LED is always on
Change-Id: I5403cfb80a57753e873c570d95ca535cf5f45630
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
TEST=Boot from scarlet, and mipi panel works
Change-Id: I52f8f8f966034f5273d7c2e673e5ebdd9dccf748
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Program eMMC DLL settings for mc_apl1 mainboard, after that system can
boot up with eMMC successfully.
Change-Id: I3d60f66ec5c7e09540ccda59f244aac6f78bf954
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The mainboard siemens/mc_apl1 uses an external I/O port for console
output. For this reason we need to activate the 8250 LPC UART.
Change-Id: Ib5616a116aec6135191bdce95f9f9566ce13d6f1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This device is no longer directly connected to the SOC so it
does not need to be enabled in coreboot.
BUG=b:35648259
TEST=build and boot on Eve
Change-Id: I4ed5a5575ce51ba5f6f48b54fab42e00134ea351
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19728
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The touchpad frequency was still slightly above 400kHz so tweak
the timing values manually to get under the spec limit.
BUG=b:35583133
TEST=verified the bus frequency with a scope to be < 400kHz
Change-Id: I8bd071a8e15a791b7551ac256797e87abd6b5e5a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19727
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Start-point is Gigabyte GA-G41M-ES2L.
This board features a G41 northbridge and an ICH7 southbridge. This
board has slots for both DDR2 and DDR3 (cannot run concurrently
though) but only DDR2 is implemented in coreboot. The SPI flash
resides in a DIP-8 socket.
Tested and working:
* DDR2 dual channel (PC2 5300 and PC2 6400, though raminit is picky
with assymetric dimm setups);
* 3,5" IDE;
* SATA;
* PCIe x16 (with some patches up for review);
* Uart, PS2 Keyboard;
* USB, ethernet, audio;
* Native graphic init;
* Fan control;
* Reboot, poweroff, S3 resume;
* Flashrom (vendor and coreboot).
Tested but fails:
* DDR3 (not implemented in coreboot).
Tests were run with SeaBIOS and Debian sid, using Linux 4.9.0.
Change-Id: I992ee07b742dfc59733ce0f3a9be202a530ec6cc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This board features a PATA port.
TESTED PATA drive works in SeaBIOS and OS.
Change-Id: I74dc72c22e6c4fed07f28ef7d88adde54656ae39
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change is needed to minimize circuit level stress, by adjusting
circuit voltage for proper operation.
For mem config GPIO changes:
To avoid leakge as those pins have internal 20K pull and 3.3K pull down
on mainboard, change internal pull up to none.
BUG=b:37998248
TEST=Boot up into OS and enter s0ix.
Change-Id: Id82035d8e1fff9fbb8dd3b4125460cdf61a58488
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/19577
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move drivers/storage into commonlib/storage to enable access by
libpayload and indirectly by payloads.
* Remove SD/MMC specific include files from include/device
* Remove files from drivers/storage
* Add SD/MMC specific include files to commonlib/include
* Add files to commonlib/storage
* Fix header file references
* Add subdir entry in commonlib/Makefile.inc to build the SD/MMC driver
* Add Kconfig source for commonlib/storage
* Rename *DEVICE* to *COMMONLIB*
* Rename *DRIVERS_STORAGE* to *COMMONLIB_STORAGE*
TEST=Build and run on Galileo Gen2
Change-Id: I4339e4378491db9a0da1f2dc34e1906a5ba31ad6
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Probe RAM to find its size instead of hardcoding 1024M.
Also properly export it to memory map.
Change-Id: Ib411f0a068bd247a9e0cd0a59689a3896921483e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
APU2 exposes a LPC header which can be used
in conjunction with a LPC TPM module.
Change-Id: If9312370a5071ffbeb6d83888c75fa69a0c27819
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/18523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This mainboard contains an external RTC chip RX6110 SA. Enable usage of
this chip and set some initialization values to device tree.
Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The thinkpad-acpi driver uses the UCMS (CMOS) ACPI method to control the
ThinkLight from the Operating System. This patch adds partial support for
that method, enough to enable or disable the ThinkLight:
echo on >/proc/acpi/ibm/light
echo off >/proc/acpi/ibm/light
With the original BIOS the UCMS method exposes a wide range of values
through a generic /proc/acpi/ibm/cmos interface. With the changes suggested
in this patch that interface is also exposed but only accepts the commands
to enable or disable the ThinkLight; all other commands are ignored.
This change would potentially benefit all currently supported Thinkpad
models, I only have an X201 available for tests though.
Change-Id: I80285f6630b5830766d82e3ecd174c4a51aa9066
Signed-off-by: Stefan Ott <stefan@ott.net>
Reviewed-on: https://review.coreboot.org/19644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Currently only one board uses this northbridge in coreboot but some
patches are pending to add more.
Change-Id: If035e442d1a23674667f46a07b44c4f2b81be48c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- set GPIO_183 to high level for enabling the power of SD card
- delete all GPIOs for JTAG interface because they lead to problems with
Lauterbach debug hardware
Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The coreboot had no supported the different frequency for gru yet.
e.g:
we can't support the bob to run ddr 800M for rev3 board and
run 928M for rev4 board.
So, in order to support the 800M and 928M ddr frequency for bob different
boards. We will use the ram_id and board_id to select the board on bob.
Change-Id: I613050292a09ff56f4636d7af285075e32259ef4
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Spread Spectrum Modulator (SSMOD) is a fully-digital circuit used to
modulate the frequency of the Silicon Creations’ Fractional PLL in order
to reduce EMI.
We need to turn the DPLL spread spectrum feature on to
reduce the EMI noise for DDR on bob.
Change-Id: I75461d4235bcf55324e6664a1220754e770b4786
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
s230u seems only have two sata ports: one for the 2.5in hdd and one for
msata. map 0x11 (port 0 & 4) enables hdd but not msata, and map 0x5
(port 0 & 2) enables both.
Change-Id: I1e9e96f0d0849b1e8c4e02aa4f686ceb5e10b3ab
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested against a lenovo-manufactured tpm 1.2 module:
a /dev/tpm0 visible inside GNU/Linux, but there is no menu items in
SeaBIOS' interface, which seems a common issue of SeaBIOS on ivb boards.
Change-Id: Id0dee74d945bae5d77eb669d8b9d468a67aee508
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19521
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This replaces the custom environment controller handling in the it8728
driver with the common library.
It also updates the two existing boards with hwm register settings in
their devicetree config so they better match their vendor BIOS fan
control settings.
Change-Id: Idf0c8908ba5ad6ff552b8302bffc638aa9052941
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/19293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
BUG=None
TEST=emerge-sand coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I86a35551a9348ff6ad26dfccd3b2786282d56069
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/19479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Configure the SD controller to handle the SD card slot.
* Galileo supports a removable SD card slot.
* Set SD card initialization frequency to 100 MHz.
* Set default removable delays.
* Build SD/MMC components by default
TEST=Build and run on Galileo Gen2
Change-Id: Iaf4faa40fe01eca98abffa2681f61fd8e059f0c4
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds the eMMC as one of the thermal sensor under DPTF.
Also, updates few comments for better interpretation and mapping.
BUG=None
BRANCH=None
TEST=Built for poppy.
Change-Id: I6d05bb7a2f857dc5bc98227c8327b2ff1bd5b913
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/19524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This reverts commit 39b633b26d.
Commit was accidentally pushed too early and broke the tree.
I'll repush the original.
Change-Id: Iaca6d43cc8fc0959565d5d151a330c0c7ba38309
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
TEST=Boot from scarlet, and mipi panel work
Change-Id: Id5f81867ea50f72cc0bc13074627134e0dc198ba
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Update the DPTF parameters based on thermal test result.
1. Update DPTF CPU/TSR0/TSR1/TSR2 passive/critial trigger points.
CPU passive point:83, critial point:99
TSR0 passive point:60, critial point:70
TSR1 passive point:50, critial point:90
TSR2 passive point:77, critial point:90
2. Update PL1/PL2 Min Power Limit/Max Power Limit
Set PL1 min to 4W, max to 12W, and step size to 0.2W
3. Change thermal relationship table (TRT) setting.
Change CPU Throttle Effect on CPU sample rate to 5secs
Change CPU Effect on Temp Sensor 0 sample rate to 60secs
The TRT of TCHG is TSR1, but real sensor is TSR2. sample rate to 30secs
Change Charger Effect on Temp Sensor 2 sample rate to 30secs
Change CPU Effect on Temp Sensor 2 sample rate to 120secs
BUG=None
TEST=build and boot on electro dut
Change-Id: I0ea0bab7fa6b0ad75d9ddacbd7cd882f91e4b0db
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/19538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Turn on device 1c.0 in order to enable devices
under it.
BUG=b:37486021, b:35775024
BRANCH=None
TEST=Boot from NVMe
Change-Id: Ide66823283c58d2bea0c9886f762f0581741affe
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19533
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is required to ensure that SCI is generated whenever a host event
is set for MODE_CHANGE. Thus, when wake from MODE_CHANGE event occurs,
eSPI SCI is generated which results in kernel handler reading host
event from the EC and thus causes the wake pin to be de-asserted.
BUG=b:37223093
TEST=Verified that wake from mode change event works fine in suspend
mode and there is no interrupt storm for GPE SCI after resume.
Change-Id: I1dd158ea0e302d5be9bcaa531cd1851082ba59fd
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jenny Tc <jenny.tc@intel.com>
soc/i2c.h does not need to be included in this compilation unit.
Change-Id: Ife11642d2e69af7235c93fc54bba38853b046169
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Currently native video init works on port HDMI1 (wired to the
on-board DVI-D socket) , HDMI3 (the on-board HDMI port), and the VGA
port, both text mode and fb mode.
Every ports works on GNU/Linux.
Tested against an IVB cpu (i7-3770T).
Change-Id: If00a7247df0c32b3d1f489fb92d86baaa8fdf8ba
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove the code that was enabling the keyboard backlight at boot
since this is not desired behavior for this device.
BUG=b:35581264
TEST=build and boot on Eve and ensure keyboard backlight does
not turn on when booting but can still be enabled in the OS.
Change-Id: I7229cf962597c0de74dc005f7afb9408f7a66f42
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set GPP_A13/SUSWARN# pin mode to native function 1. This pin is tied
to SUSACK# in the schematic and and is intented to be used in Deep Sx
so it should not be configured for GPIO mode.
BUG=b:35581264
TEST=build and boot on Eve platform, test that Deep S3 and Deep S5
are still functional. (this change should have no visible effect)
Change-Id: Ie2dc24d095872ab93a5bfcbe5307c3b7a8e4dbcc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Board Scarlet doesn't use usbphy1.
BUG=b:37685249
TEST=boot Scarlet, check the firmware log, and confirm
no errors about USB1
Change-Id: I66e0d8a235cc9057964f7abca32bc692d41e88fd
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add some known good values for some thinkpads displays.
Known good means that at this pwm frequency the display is evenly lit
on all duty cycles, the display makes minimal to no noise at lower
duty cycles and the display does not flicker. This values differs from
vendor (which uses an obviously wrong display clock (190MHz instead
of 320MHz) resulting in frequency more than 60% off the intended
value.
TESTED on Thinkpad X200 with edid ascii string in list and removed
from list to see if notice message is shown.
Change-Id: Id7bc0d453fac31e806852206ba2c895720b2c843
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
1. Add support for using cr50 I2C TPM on poppy. This will not be
enabled until the next build.
2. Also, configure GPIOs for SPI and I2C TPM only if the corresponding
Kconfig options are set.
BUG=b:36265511
TEST=Verified on a reworked board that I2C TPM communication works
fine.
Change-Id: I3b293b8d410a6973a6dfea393c17d0be425b6a28
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The AFC—Additional Flash Control Register is set by
southbridge code.
Remove redundant calls and get rid of it in autoport.
Change-Id: I627082e09dd055e3b3c4dd8e0b90965a9fcb4342
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19493
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Based on Thinkpad x230 and schematics.
Verified by autoport.
USB debug port is the left front usb port
Thanks to Holger Levsen for the device.
Change-Id: I97c8e01a3ce0577d7dc9e8df7d33db3b155fe3d6
Tested-on: lenovo x1 carbon gen 1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16994
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Haswell, Broadwell, Baytrail, and Braswell ChromeOS devices'
FADT version were incorrectly set to 3, rather than the correct
ACPI_FADT_REV_ACPI_3_0. The incorrect value resulted in these
devices reporting compliance to ACPI 2.0, rather than ACPI 3.0.
This mirrors similar recent changes to SKL and APL SoCs.
Test: boot any affected device and check ACPI version reported
vai FADT header using OS-appropriate tools.
Change-Id: I689d2f848f4b8e5750742ea07f31162ee36ff64d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Enable audio:
* Add verb table for ALC286 & ALC298
* Enable virtual channel 1 for DmiVc1 & HdaVc1.
TEST= Build for kblrvp3 as well as kblrvp7. Boot to OS & verified
working of audio on both the boards.
Change-Id: Id27e3cf585b93ed4131d7bf3d3b53d3f5404b18e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18875
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable/Disable the PCIe ports to match factory BIOS. The port #6
is used for PCIe on the M.2 connector which allows for NVMe SSDs
to function.
Change-Id: I8058cbad3da651144545d588c0ae78c5f5e598ac
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19446
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Correct the default GBB_HWID to "ROWAN TEST 9387"
BRANCH=chromeos-2016.05
BUG=b:35774871
TEST=emerge-rowan coreboot chromeos-bootimage,
strings /build/rowan/firmware/image.bin | grep "ROWAN TEST"
and look for 9387 in output
Change-Id: I7851010305caf056958c8a6a328b0506bf2208cd
Signed-off-by: Patrick Berny <pberny@chromium.org>
Reviewed-on: https://review.coreboot.org/19488
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Enable separate MRC cache for recovery mode. This requires change in
flash layout to accomodate another region for RECOVERY_MRC_CACHE.
BUG=b:37682566
TEST=Verified following scenarios:
1. Boot into recovery does not destroy normal mode MRC cache.
2. Once recovery MRC cache is populated, all future boots in recovery
mode re-use data from the cache.
3. Forcing recovery mode to retrain memory causes normal mode to retrain
memory as well.
Change-Id: I4c748a316436001c5a33754084ab4a74243e21df
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19457
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This needs some extra headers in amdk8/raminit.c that were otherwise
provided by that file.
Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19360
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BUG=b:35647967
TEST=boot from bob
Change-Id: I756513f02ac13e159d5b8b1ac2346fa42cf3c219
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf18ed7b8fdf11594f812e5c48a2bd0fde5cb820
Original-Change-Id: I50c053ab7a6f6c14daee4fb2ab1cdcaeee2d67da
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452286
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19434
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
SD card detect pins should normally have a pull-up. It seems that for
micro-SD cards this doesn't really matter all that much, but for the
full-size slots we have on some Oak-derivatives (like Hana) it does.
BRANCH=oak
BUG=b:35854317
TEST=Booted Hana, confirmed that card detect no longer seemed stuck-on.
Booted Elm and confirmed that SD card behavior didn't change.
Change-Id: I9b20e0f6fe310e724d191e36ca0a81ab4fe5f593
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c2781eeef50f52c6f02ee9344274ddf4dcb0a946
Original-Change-Id: I428ac92efb07f94265673b04e0e0dd452649b9fd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/452861
Original-Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/19432
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new touchpad firmware uses i2c-hid instead of custom reporting
protocol. The touchpad also exposed another slave address (0x1e) for
kernel to communicate with the touchpad EC.
Change-Id: Iecaf14f7b8aed836120569e9ade9c3115bc00264
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/19461
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=b:35586577
BRANCH=none
TEST=On a poppy board that has the VBUS rework applied, plug in a charger to
either port and see charge status updated to indicate charging in the
power_supply_info tool and the Chrome OS UI.
Change-Id: I59dcfc1cb5d11841f56cac7f4ffe461c2f9ec52a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/19441
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
For this debug.c needs to be linked too.
Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
BUG=b:37486021
BRANCH=None
TEST=compile coreboot and make sure sda and sdb show
up in /sys/class/block.
Change-Id: I11344a4a5fc7e5b5d907d25439f92744a5fb70da
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19450
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Replace ram_check with quick_ram_check, because ram_check is slow and
is destructive for dram content.
Change-Id: I5fb1bfe711549aabb6e597bda22848988a7e9cbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19416
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The silicon specific mainboard_romstage_entry() in amd/cpu/car.h,
which is used by all AMD silicon car code, caused a conflict.
Move the silicon specific defines to silicon header files. Also,
no longer include car.h in the romstage file.
Change-Id: Icfc759c4c93c8dfff76f5ef9a1a985dd704cfe94
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The devicetree data structures have been available in more than just
ramstage and romstage. In order to provide clearer and consistent
semantics two new macros are provided:
1. DEVTREE_EARLY which is true when !ENV_RAMSTAGE
2. DEVTREE_CONST as a replacment for ROMSTAGE_CONST
The ROMSTAGE_CONST attribute is used in the source code to mark
the devicetree data structures as const in early stages even though
it's not just romstage. Therefore, rename the attribute to
DEVTREE_CONST as that's the actual usage. The only place where the
usage was not devicetree related is console_loglevel, but the same
name was used for consistency. Any stage that is not ramstage has
the const C attribute applied when DEVTREE_CONST is used.
Change-Id: Ibd51c2628dc8f68e0896974f7e4e7c8588d333ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19333
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the safety considerations, we should make sure the slot of SD is
enabled first, since we want to the power switch of corresponding is
powered up.
The different boards have the different power switch for sdmmc.
Some power switch IC need turn on delay for long time.
let's move the slot power of SD to romstage and avoid explicit delays
or per-board.
BRANCH=none
BUG=b:35813418, b:35573103
TEST=check the signal for children of gru, and boot up from sd card.
Change-Id: Id164e4c4c900c6b1ca0251fc27db4cd36c56f6ff
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ea1b01cc13628033b85251dbb44407f075efdc85
Original-Change-Id: I48ab543143d3de9be46608fc12d78e09decf8d79
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/447076
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19430
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Delete the write to PM register 0xee. This register is not
listed in the current BKDG and S4 is not currently supported
on this APU.
NDA document #47517 "A55/.../A85X fusion Controller Hub Register
Reference Guide" provides some clues on the intent of this write.
This register has always been observed to power on with a value
of 0x08 so the write has no effect.
This should be revisited again when SMI and PSP fully implement
the support required for S3.
Change-Id: I35e6c5f7ad1de7f51b018543d2f7ce82182f11e4
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18494
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Unlike other oak derivatives, Rowan uses an 8-lane BOE tv097qxm-nu0
MIPI/DSI panel that requires dual DSI support.
Rework oak display initialization to special case Rowan, which uses a
provided edid struct for its panel, special panel backlight sequencing
and needs to configure mtk_ddp and mtk_dsi to use dual dsi mode.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: I136ba5bd1ab12c4ad92995e066fc6d6cf54d0898
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19389
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
This helper function was introduced so that mainboards don't need
to manually fill in these struct edid fields.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Ic9404a786a28b314b710e037dcae776be4b584ca
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19388
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: If66a2a1d461a411e112589c84a434066d48b9399
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19410
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ia1eacd15e71a46a37457ee2f117b156393c3393d
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19409
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ifeb09a0a35bff7cd9091f6d027f0065288ca35c9
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Utilize the intel/common code for tis_plat_irq_status() to remove
dependencies and code duplication on for bringing up a board
requiring tis_plat_irq_status().
Change-Id: I2aaa1d7d3ce171dc1788438ff9990fce533deb6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19371
Tested-by: build bot (Jenkins)
The CR50 TPM can do both SPI and I2C communication. However,
there's situations where policy needs to be applied for CR50
generically regardless of the I/O transport. Therefore add
MAINBOARD_HAS_TPM_CR50 to encompass that. Additionally,
once the mainboard has selected CR50 TPM automatically select
MAINBOARD_HAS_TPM2 since CR50 TPM is TPM 2.0.
Change-Id: I878f9b9dc99cfb0252d6fef7fc020fa3d391fcec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19370
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
For raminit to succeed on a hot reset the following things are
prevented from running:
* Clearing self refresh
* Setting memory frequency
* programming sdram dll timings
* programming rcomp
TESTED on Intel d510mo.
Change-Id: I8f7e5c2958df29a96cdf856ade2f4f33707ad362
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19337
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There is no need to override CBFS_SIZE since there is no additional
firmware needed on the flash.
Also due to it having a description CBFS_SIZE was displayed twice in
menuconfig, which is fixed by this.
Change-Id: I1a8e2e458ac4d420f3fd4628c2805b6d4e2ee529
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19331
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested on X230 with an external screen connected to every one of the
DP ports (miniDP on mainboard, two DP ports on dock), the GRUB payload
can display on both the external screen and the internal LVDS screen.
This is a copy-paste of I8e02c8003ff745d05ee272c59377174847f5219c.
Change-Id: I8f270d558668c1fe41bcdcc7d6d2aa7f053c85b6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/19412
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Lid switch is not available.
Hence report lid state as always open.
Change-Id: Ia9c82c3ad323912bad51cf55ed80a37b3110b1ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19219
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Read DRAM SPD and populate MemorySpdPtr fields
in UPD data structure for FSP.
BUG=b:36490168, b:35775024
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/fizz -x -a
We are currently working on bringup and have no
hardware to test on yet.
Change-Id: I191cc6bf1fd8aa461855c538b48fd39e3ffd7848
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19205
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This board was added while the latest libgfxinit changes were in review.
Update to make it compile again and sanitize the port list.
Change-Id: I81b96e225945a8f8e47b64cefea91eb2747675ca
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19353
Tested-by: build bot (Jenkins)
Reviewed-by: Nicola Corna <nicola@corna.info>
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static and empty ASL file.
Delete src/drivers/pc80/tpm/acpi/tpm.asl.
Change-Id: I6163e6d59c53117ecbbbb0a6838101abb468de36
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In the single GPU configuration, the T420 has an LVDS port, one DP++
and one VGA port connected to the IGD. Docking solutions feature up to
two additional DP/DVI-D ports, also directly connected to the IGD.
This makes the list of ports to probe pretty long (takes about 70ms
if nothing but LVDS is connected). We could save about 20~30ms if we'd
limit the ports in case we are not docked or have a discrete GPU.
Change-Id: I8e02c8003ff745d05ee272c59377174847f5219c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19378
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This commit changes the interrupt configuration for the touchpad to be
level triggered so it matches what the device is actually using.
When the system wakes from suspend by way of touchpad interrupt, or
there is touchpad input while in suspend that does not wake the device
(when the device is in tablet mode) the interrupt edge is not seen by
the AP so the driver does not handle the event and the touchpad keeps
the interrupt asserted and does not send further interrupts. The end
result is a non-functional touchpad after resume until it is reset or
the driver is reloaded.
This happens because the touchpad is actually treating the interrupt as
level triggered and expects the kernel driver to read a data packet over
I2C before it will de-assert the pending interrupt.
BUG=b:35774857
BRANCH=none
TEST=Test that the system can reliably wake from suspend by touchpad
event via the EC and continue to have a functional touchpad after resume.
Change-Id: Iaf7c04d9bc9d945bdcc196dff54c92a2a68368f3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19382
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Issue TPM startup on romstage completion via common LPC TPM
code if the TPM was enabled in Kconfig.
Change-Id: Id886d6aeefa045fb979f128b1cf4c10fff243b24
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19338
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kevin's center logic isn't super clean so it needs 925 mV for center
logic. All newer gru variants only need 900 mV.
BRANCH=gru
BUG=b:37429075
TEST=Reboot tests
Change-Id: I8c3bd6c245700b23c27cd5758c35c9993f801cb4
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/479463
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19357
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It seems that we should only ever run at 900mV on center logic.
Changing it to 950mV before might have just masked over problems that
are now fixed.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=on kevin, run
stressapptest -M 1536 -s 1000
Change-Id: I5a09b1b403df800396bb2f2e8c76d14a4519d44a
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/391032
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Commit-Queue: Lin Huang <hl@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Create Soraka board which derives from Poppy, a KBL reference board.
More Soraka specific changes need to be done later on.
BRANCH=master
BUG=b:36995255
TEST=Build (as initial setup)
Change-Id: I8af68d2cf475df56336aa0e3bebe86a54ece1999
Signed-off-by: YH Lin <yueherngl@chromium.org>
Reviewed-on: https://review.coreboot.org/19343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Move current NHLT configuration implementation to baseboard so that
variants can leverage it or provide their own configuration.
BUG=b:37375693
Change-Id: I2a4317c112f9e3614bd01eb6809727b73328d29d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure that
required SPD hex files are included in the SPD binary.
BUG=b:37375693
Change-Id: Ic9bcc03d5a35bebd14061680f264ac072b3c0634
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19325
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to be able to share code across different poppy variants,
provide the concept of baseboard and variants. New directory layout:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/poppy - code
variants/poppy/include/variant - headers
New boards would then add themselves under their board name within
"variants" directory.
This is purely an organizational change.
BUG=b:37375693
Change-Id: If6c1c5f479cfffe768abf27495d379744104e2dc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19322
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Clean up Kconfig file in order to support variants for poppy. Add
BOARD_GOOGLE_BASEBOARD_POPPY that can be set by various poppy variants
to use the common baseboard configs.
BUG=b:37375693
Change-Id: I399ecc8c3efb3af26e1fcf60fe2c75b24769fc0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19321
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add camera related support
* Enable the SA Imaging Unit and CIO2 devices.
* Enable TPS68470 PMIC and populate related ACPI objects.
* Enable OV cameras and populate related ACPI objects.
* Enable Dongwoon AF DAC and populate related ACPI objects.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that ACPI tables
have the required entries for all the camera devices.
Change-Id: Ifbe878bb6b25fc976e935fee16c4d59fadd47fe2
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18969
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This patch includes ipu.asl file in the main DSDT definition
to add ACPI entries for IMGU and CIO2 devices.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: Ib7485315cb9468da7c6aa090862657a265121493
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19110
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Update formatting of gpio table to fit everything within 80 column
limit.
2. PEN_RESET gpio is non-existent. Get rid of it.
BUG=b:37375693
Change-Id: I1bcc4168659f365547e5f7227df8659e4bc7f243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19320
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable lower power state when running on battery. Deep S3 is not
enabled when in AC mode to support standard "docked" config.
BUG=b:36087058,b:36723679
TEST=Verified following behavior with USB mouse:
1. If AC is connected when entering S3, USB mouse is able to wake up.
2. If AC is not connected when entering S3, USB mouse does not wake up.
3. If AC is connected when entering S3 and removed after entering S3,
USB mouse does not wake up.
4. If AC is not connected when entering S3 and attached after entering
S3, USB mouse does not wake up.
Change-Id: I141a8d4779de004e27fcd9357cef787a38a27b24
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19276
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static ASL file.
Change-Id: I3cb2a8a3ac337d1de8a3c394d7a28155597239d0
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19283
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Commit bf264e94 (i945:) adds a PCI reset to the romstage, and commit
bc8613ec (Fix i945 based boards) fixes that to use the correct
delay of 200 ms. This code was then copied over, when adding support for
the Lenovo T60.
The reset was related to the shipped crypto card on the Roda RK886EX and
Kontron 986LCD-M, so is not needed on the Lenovo T60. So remove it, to
reduce the boot time by 200 ms.
The same change is done for the Lenovo X60 in commit 7676730b
(mb/lenovo/x60: Remove PCI reset code from romstage).
Change-Id: Ifff43f095a1236c9e9a9ef0687e8efe42e72c971
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19298
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
The HDA verb for falco/wolf's internal mic was wrong, preventing the mic
from working properly in Windows and macOS (the Linux driver overrides
the verb table, so wasn't affected). Set the verb connector/jack bits
properly, to no connector / no jack detect, in order to fix.
Also, make (2) small non-functional fixes:
On falco, NID 0x1A was being disabled twice (instead of 0x1A and 0x1B
both being disabled - copy/paste error).
On wolf, NID 0x19 was set to an internal analog mic, where it should have
been disabled (again, copy/paste error).
Both these errors were introduced when consolidating/upstreaming
and were not present in the original Chromium sources.
Test: boot Windows [8/8.1/10] and verify mic functional with Realtek
drivers on both falco and wolf.
Change-Id: I9c343dda4762f0b1f814318c155e22c59d2da8db
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Remove the 'probed' setting from the Realtek 5663 headset codec I2C
device. This was added when we had a hardware issue that was preventing
I2C operation because the clock/data lines were swapped.
With new and/or reworked hardware this is no longer a problem and we do
not want the I2C layer in the kernel to talk to the device before the
rt5663 driver.
BUG=b:35585307
BRANCH=none
TEST=Boot on Eve and verify rt5663 driver still loads properly.
Change-Id: Ice38889e8f5d3fd1307056cab10fbe3f4e197749
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19304
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
.jpg){kind=link}
.jpg){kind=link}