This change adds variant rammus derived from baseboard poppy.
The setting is copied from the poppy and will be modified later
BUG=b:111579386
BRANCH=master
TEST=emerge-rammus coreboot
Change-Id: I169c225e28183a7a93f1142a3bf87a60b26ce9ca
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable DW9807 NVM support by adding required ACPI code
BUG🅱️110815821
TEST=On Nautilus board, execute "cat /sys/bus/i2c/devices/i2c-INT3499:00/eeprom"
in the terminal and see if there is any data to be dumped.
Change-Id: Ib83fa1a522402a59566e3f55fa5c1af4490266e4
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Reviewed-on: https://review.coreboot.org/27508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Nautilus-WiFi board doesn't have external pull-up on USB2_OC2# route,then
abnormal over-current is asserted on USB type-A port.
It causes USB type-A port to be blocked, so we need this internal pull-up.
BUG=b:111578984
BRANCH=poppy
TEST=Verified over-current not triggered abnormally on basic sku board
Change-Id: I159f686cef9c8d254f390d7f1dff8011f43fc066
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the GEO SAR feature for nocturne. OxM programs wifi_sar VPD key in factory.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:65155728
BRANCH=none
TEST= Set the wifi_sar VPD with below command (values are junk for test purpose only,
actual values would be set be OxM)
sudo vpd -f <coreboot.rom> -s wifi_sar=30313233343536373839303132333435363738393030313
24142433435364445463031324142433400364445463031323343444546303132333435
Flash the <coreboot.rom> and boot to kernel. Get ACPI table and WGDS would get created
with VPD values passed in.
Change-Id: I32ad591f15fdb34704c8d98d98646dfa2d8882ff
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to sona thermal table, PL2 need to check cpu id.
And then set PL2 value.
BUG=b:110867809
TEST=The thermal team verify OK
Change-Id: I5759fb3c685e3d4eef1be054541f950843d19874
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This commit changes the uid and desc fields for the sx9310 entries
in the devicetree to be unique, and correctly identify the position
of the respective sensors.
Change-Id: I501df7d3349fdebc9673c9815f5b1b2458abac6e
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
We would use GPP_B20 instead of board id to determine nautilus SKU.
BUG=b:80052672
BRANCH=poppy
TEST=Verified the new coreboot could determine SKU correctly
Change-Id: I1978b544eef7a184a3da191306ee32d862fa8c36
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27220
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We found GPP_C3 keeps high when system in S0ix mode. It caused 1.8V
leakage. To fix this problem, add GPP_C3 into config for Pantheon
Synaptics touchscreen.
BUG=b:78436458
BRANCH=None
TEST=Let DUT in S0ix mode and check GPP_C3 is normal.
Change-Id: Idb2dab93178af1dae54265e49522b473b69a35af
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This configures a GPIO pin for enabling/disabling bluetooth on the
next version of the atlas board. The default is for bluetooth to be
enabled at this point.
BUG=b:110614620,b:110613353
BRANCH=none
TEST=none
Change-Id: I4ba940e89b1dc03548b7ab44b8f84dc9a3097acb
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When played Left Only Audio and Right Only Audio, we observed that Audio
got swapped. Left Data played on Right Speaker and Viceversa.
This patch fixes the above issue.
BUG=b:73635449
TEST=Play Left only & Right only Audio and cross check Audio.
Change-Id: Ie9c417ad0634a76fc8a4126ee75886603f1b3da0
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27167
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set register speed_shift_enable=0 in devicetree to disable
p-states in coreboot as a temporary workaround for an SoC hang.
BUG=b:79666828
BRANCH=none
TEST="emerge-nocturne depthcharge coreboot chromeos-bootimage",
flash spi image onto nocturne, boot to kernel and verify device
stays alive and responsive for several minutes without locking up.
Change-Id: I71ed4c80c109b28ffa85d48338ce3a62396d272e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is a temporary hack to test camera presence before we have full
camera support implemented. Basically, we can now probe the camera
over i2c to verify that it's connected and the camera LED turns on.
BUG=b:80106316
BRANCH=none
TEST=camera LED comes on and camera can be probed over i2c.
Change-Id: Ibaabf6c6f6a1dabaddd2fc47c820e090ca5984a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27128
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We plan to use i2c-hid compatible trackpads on atlas, so this switches
the trackpad config to i2c-hid.
BUG=b:80662079
BRANCH=none
TEST=used trackpad to verify motion tracking
Change-Id: I2702e61a6aa96250c0c09ea4bd15d0c671eedadc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27126
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change defines SAR sensor device into devicetree.cb.
Since only LTE sku has SAR sensor, we will use GPP_B20 as a device_present_gpio.
BUG=None
BRANCH=poppy
TEST=Verified SAR sensor device is loaded by driver in Chrome OS
Change-Id: Ib4969e4b82d18b1b1a599de8226c2d7d4bda7915
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27149
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Nautilus 2nd SKU has a leakage voltage at GPP_D0 in S5 state. We need to set this to LOW when entering S5 for clear the leakage.
BUG=None
BRANCH=poppy
TEST=Verified the leakage is gone after update coreboot
Change-Id: I054e707b2bc2e63d6f99cd2fd8a57be20615f111
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For supporting new SKU, we need to override GPIO table and device configuration.
The board ID of 2nd SKU of nautilus is started from 9, so we would determine SKU with it.
BUG=b:80052672
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7242f23f47010664cc29ea86a126e63c9dd62ccd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27147
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to schematic, we need to correct USB OC pin configuration.
- OC0 for Type-C Port 1
- OC1 for Type-C Port 0
- OC2 for Type-A Port
- OC3 to NC
BUG=NONE
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ic71baef646926cc6aadcc5dda7cb14f00e8d3687
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update dptf.asl and TCC parameters from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI
Change-Id: Ic0ffc169ad3939cacb46824ed23999c61a23d2c4
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_E2 will be used as a BT reset line, so configure GPP_E2 as an
output and initialize it high (high = out of reset).
BUG=b:80089559
BRANCH=none
TEST=none
Change-Id: If45ef3a592c389a0b80298c59eea849d07d9671e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FCAM_PWR_EN signal is changing to connect to GPP_B4 instead of
GPP_D8 as it needs a 3.3v gpio to provide enough power to also
directly power the camera LED.
BUG=b:79667559,b:78122599
BRANCH=none
TEST=none
Change-Id: Ie875ced45dfa2aa7069851004edde8f77329df34
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Add tablet motion control config to nami devices.
BUG=None
BRANCH=None
TEST=run evtest
make sure tablet switch value is 1 in tablet mode and 0
when not in tablet mode
Change-Id: Ie1480934dc003d9b467883e001ed89f9a3694d10
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26970
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TPM over SPI/I2C config selection got changed in
https://review.coreboot.org/c/coreboot/+/24903 so this CL is fixing the
same.
BUG=None
BRANCH=None
TEST=Build for Soraka & make sure that TPM is probed over I2C interface
rather than SPI.
Change-Id: I077e4dc03520e26eb9f6404a7eb1edd99925de77
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26890
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are two cameras on Nami and only one camera on Sona.
We need to disable rear camera/DMIC on all Sona sku.
BUG=b:109710674
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Sona
Change-Id: Id84ee22c9ffc15db78be3bbad148af5cd7dc866e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since there are two cameras on Nami and only one camera on Pantheon.
We need to disable rear camera/DMIC on all Pantheon sku.
BUG=b:109720689
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Pantheon
Change-Id: Ibe48a945dc57f2c05344479253040ad1945d92fd
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Issue observed on the board is: too many jack interrupts.
cat /proc/interrupts | grep da7219
58: 84292 15709 0 0 IO-APIC 58-fasteoi da7219-aad
Updated pad configuration for Jack IRQ pin to fix the issue.
BUG=b:109655907
TEST=Jack insertion & removal detection is working.
Change-Id: I41ef9d40325677b01ca94ec3215e7feded76dcc3
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
During measurement of signals during Elan touchscreen power on, saw
that the enable_gpio delay was not sufficient as there is a +1.5 ms
delay during power on. Adding more delay to take this into account.
BUG=b:78311818
BRANCH=None
TEST=probe power on signals to ensure meet timing requirements
Change-Id: Id661a202188a97aef97514ebecd0be6fc022d21e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Power off does not seem to use the ACPI _OFF function, but rather the
smihandler. Creating variant_smi_sleep function for nami to handle
the power off sequence during reboot/power off.
BUG=b:78311818
BRANCH=None
TEST=Run "poweroff" command from AP console with SMI_DEBUG enabled
Make sure delays are consistent with spec
Change-Id: Ifeea545fe268be249793b3e508c51f5e4c1a3460
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since Vayne added one more skuid 3A67, we need to disable rear
camera/DMIC for vayne skuid 3A67.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Vayne
Change-Id: I9131b4c41bf189829be4e7e6bfaf4a96765cfa15
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26855
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The driver only supports streaming images flipped horizontally
and vertically. In order to ensure that all current users will
be fine if or when support for upright streaming is added,
require the presence of the "rotation" control now.
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: I7e3abdea9071da1a089c7165f6bb609428090792
Signed-off-by: Lai, Jim <jim.lai@intel.com>
Reviewed-on: https://review.coreboot.org/26727
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FPMCU is using the standard cros-ec-spi interface on GSPI1.
Configure the GPIOs controlling the MCU too.
We need to be able to wake from S3 on the MCU interrupt, re-configure
GPE0 DW0 to point to GPP_C bank.
BRANCH=poppy
BUG=b:79666174
TEST=exercise the cros_ec interface, e.g. 'ectool --name=cros_fp version',
verify the MKBP events by doing 'ectool --name=cros_fp fpmode fingerup'
then 'ectool --name=cros_fp waitevent 5 10000', toggle the other GPIOs
with the flash_fp_mcu script.
Change-Id: Ib417dcf84cda8e354060785cd16a7b6b812148d5
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/26684
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves PL2 override to variant_devtree_update for two reasons:
1. This function was added to basically override devtree settings in
variant specific code. So, it would be a good idea to perform all the
overrides in a single place.
2. Adding a device for performing nami_enable would require changes to
devicetree and special handling for calling this device enable. Thus,
nami_enable was never getting called.
BUG=b:80148703
Change-Id: Ifa24a7b6e99cad2368b3d656a757f26297373121
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Drive SPKR_RST_L (GPP_A19) high at boot to take audio amps out of
reset.
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage", boot to kernel,
and verify sound works via "aplay /dev/random"
Change-Id: Ia49931f2dc7802edc8a46114b081e4a96eeee604
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The I2C CLKs of SoC should be 400kHz, but waveform show 460kHz to
470kHz. Add I2C parameters to adjust I2C CLKs which 5% lower than
400kHz.
BUG=b:78819970
TEST=The I2C CLKs are 5% lower than 400kHz.
Change-Id: I2c3012b5b59c089801cda8fd7b0c433aad9df36d
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26282
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update dptf.asl from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI.
Change-Id: I21ddc337359c3e11ad9756e61ba174b33dfc3c75
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Since there are two ALS device nodes on Nami, need to remove one.
BUG=b:79227879
BRANCH=master
TEST=Verify if only one ALS node is found in /sys/bus/iio/devices
Change-Id: I850af06bec833739afa0c8c516d351d81952ce2c
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26271
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds board-specific implementation of
mainboard_vbt_filename which returns "vbt.bin" by default. This is in
preparation to allow multiple vbt binaries to be added to single
image. More sku_id specific names will be added in follow-up CLs.
BUG=b:79396300
Change-Id: I3821d55bfbe9e5773bd2eb0b0003045a80158d8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This adds a new SPD entry for samsung's new 4GB memory and updates
atlas to use it instead of the previous gen memory.
BUG=b:79444337
TEST=booted on atlas
Change-Id: I19567736c45a1321586378c3d964c2cbebe24755
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/26185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch updates the below:
1)
Nocturne board has only Max98373 speaker amp.
Update both NHLT and DT entries to include only Max98373
and not include DA7219.
2) I2S2 is used for Boot Beep.
So, update GPP_F0 ~ F2 pins accordingly.
3) Include DMIC-4ch configuration.
BUG=b:79362472
TEST=None [Waiting for HW to verify]
Change-Id: I0e9b3a564c22de6e84e96e5e937a3aca4ae73d75
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change:
1. Allows mainboard to add OEM table to CBFS
2. Provides mainboard specific smbios_mainboard_manufacturer that reads
OEM ID from EC using CBI and compares it against the OEM ID in CBFS
table to identify the right OEM string.
BUG=b:74617340
Change-Id: Iff54b12745de3efa7be0801c9a3a9f2a57767dde
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I8e549e4222ae2ed6b9c46f81c5b5253e8b227ee8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
From coreboot side, include DMIC 4ch NHLT configuration and its
DMIC blob. In OS side, cras picks the needed channels using UCM's
channel map configuration.
So, this patch updates to include DMIC 4ch config.
BUG=b:79158926
TEST=Verified 4-ch record with arecord
TEST=Also verified internal mic record with cras using
'cras_test_client --capture_file dmic.raw --rate 48000
--num_channels 2 --duration 10'
Change-Id: Ic6df00c2f26ad9cdf54152ab021c2b10499c429c
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This gpio should be active low, but is not currently configured that way.
Changing gpio configuration to reflect that.
BUG=b:73121017, b:77941823
BRANCH=None
TEST=iotools mmio_read32 0xfdae0588 (GPP_E1) Make sure that when pen
is ejected, gpio is low and when pen is inserted, gpio is high.
Also tested that wake upon pen eject is working.
Change-Id: Ic49eea6412c3378dca39a3338b43df12bc27037d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26017
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's very confusing trying to find the google platform names, because
they seem all unsorted in Kconfig. They're actually sorted according
to the variant name, but previously, that was impossible to tell.
- Add a comment to the top of variants in Kconfig.name
- Inset each variant name. If you start a prompt with whitespace,
it gets ignored, so after trying various ways to indent, the arrow
was the option I thought looked the best.
It now looks like this:
*** Beltino ***
-> Mccloud (Acer Chromebox CXI)
-> Monroe (LG Chromebase 22CV241 & 22CB25S)
-> Panther (ASUS Chromebox CN60)
-> Tricky (Dell Chromebox 3010)
-> Zako (HP Chromebox G1)
Butterfly (HP Pavilion Chromebook 14)
Chell (HP Chromebook 13 G1)
Cheza
*** Cyan ***
Change-Id: I35cb16b040651cd1bd0c4aef98494368ef5ca512
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This configures GPP_A23 as a wake source for the trackpad. We also
need to set up GPP_A GPE0_DW0, thus evicting GPP_B. We don't have any
interesting signals in GPP_B, so we won't be missing it.
I don't have hardware with A23 wired up, so i just tested the wake
source using A19 which is essentially identical to A23.
BUG=b:78541883
TEST=verified we can trackpad can wake system from suspend
Change-Id: If800464c8b2319d758b1823850571919f85bdc6c
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds keyboard backlight feature for Nami platform
BUG=b:78360907
BRANCH=none
TEST=keyboard backlight works when EC reports correct info.
Change-Id: I3fceb83e155032b6e9f1763c4e2a29e7521269d2
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change sets VmxEnable to 1 to match the kernel setting.
If this feature is enabled at the kernel level and not in FSP,
then there is an issue where FSP expects it to be disabled so
it forces a cold reboot on every warm reboot.
BUG=b:78129261
BRANCH=poppy
Change-Id: Idedbde1d8eb0c9e959733b7b50e5dec804d61cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25698
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating some GPIOs based on changes in the latest schematics. Also
renaming signals to match that of latest schematics.
BUG=b:73749640
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Make sure different SKUs still boot.
Change-Id: I7d912f4bc6765f065c75c68a45bdf9ee844e0c1d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The commit enables DPTF function. The DPTF parameters are provided by
thermal team.
BUG=b:72974136
BRANCH=poppy
TEST=emerge-nami coreboot then check the parameters in DPTF ui tool
Change-Id: I9b7ae34ee64f19ef783a8c1571831b2293105a18
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add SPD file for sdp hynix_dimm_H5AN8G6NCJR-VKC (ram id: 15).
BUG=b:77893710
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I434d42ff12e6dae39e5676f36ba6cf00b3a48b06
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add SPD file for sdp micron_dimm_MT40A512M16LY-075E (ram id: 14).
BUG=b:77930401
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: Ia44e70948e57c2f19664d874ae005ac39d748f92
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since there are two cameras on Nami and only one camera on Vayne.
We need to disable rear camera on all Vayne sku.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera shown on Vayne
Change-Id: I6e7c1e8791462f00ad8336372954ee0a9465d9b8
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add SPD file for sdp hynix_dimm_H5AN8G6NAFR-UHC (ram id: 6).
BUG=b:77290144
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I33503de21c9fc14537c00c092986fd4d2998dace
Signed-off-by: chriszhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
Add a new variant of Poppy for the Atlas board.
BUG=b:75454415
TEST=tested on a P0 board. System boots and is mostly
functional, though some peripherals are not ready so there
are no touchpad/touchscreen devices configured yet.
Change-Id: I5a0bccd1bda0134aa51885ac2c6e7bb5b45de924
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change remove work-around code for the power issue of MIPI and
USB cameras on previous board revision. With the work-around code,
PMOF ACPI method cannot turn off MIPI camera. So we need to remove
it.
BUG=b:74214248
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/25337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tools/scripts, like mosys/arc-setup, use int (4 bytes) to
read the sku id. In order to support "-1", we need to use
uint32_t (4 bytes) instead of using uint16_t (2 bytes) data type.
Otherwise, tools/scripts will read 65535 instead of -1.
Another reason to change this is that sku_id can be
supported by ec up to 4 bytes.
BUG=b:73792190
TEST=mosys output "Platform not supported" for -1 sku id
arc-setup read -1 sku id
Change-Id: Ib3baa8419f138abeb412ac09c2e7dc608e3b758b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Touchscreen power enable for Nami has moved from GBB_C22 to GPP_B4 in
the latest schematics.
BUG=b:74347464
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I3b1794d44f25c0d42d082d63b9e3ec3dfcef7528
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25154
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since nami proto did not have any external pull on MEM_CONFIG_4, use a
weak internal pull down before reading it.
BUG=b:74420123
TEST=Verified that the value read for MEM_CONFIG_4 is correct on nami.
Change-Id: I45989d2ca35b863f391baba9e2f2e602033217d4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Make sure that fields that are not updated in
variant_memory_params keep a default value of 0.
In particular, use_sec_spd is intended to have a default value of
0 on all platforms. Without this patch, a random value is used
and all boards (except nami) get stuck on boot.
BRANCH=poppy
BUG=b:74439917
TEST=Nautilus and poppy can boot, and do not get stuck at
"CBFS: 'sec-spd.bin' not found."
Change-Id: I06c6511625de930903ae13788bdcd27667a17886
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/25101
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change SECONDARY_SPD_SOURCES to SEC_SPD_SOURCES as that is what the
spd target expects.
TEST=Verified that sec-spd.bin is present in coreboot.rom
Change-Id: I4299df1eb9009095ef899c5b83823750dfc715d8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Per vendor datasheet, corrected linkfreq of imx258 as
{633600000, 320000000}
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: Ie5beed44c15e26b9f82cb305a91b8ff90a9ea867
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-on: https://review.coreboot.org/24990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
As per the latest schematics, this change configures GPP_B0 as wake
source for WLAN.
BUG=NONE
BRANCH=master
TEST=emerge-nautilus coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I72b940452cfbbe471279ef117a868a8ae0b65b8b
Reviewed-on: https://review.coreboot.org/23526
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alkali will use LPDDR3, so need to have Nami support both
DDR4 and LPDDR3. We do this with the PCH_MEM_CONFIG4 GPIO.
BUG=b:73514687
BRANCH=None
TEST=None
Change-Id: Ife6740ce0e8fe109ded7b954134171ba91895628
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add spd files for LPDDR3 based on info received from factory team.
BUG=b:73287172
BRANCH=None
TEST=None
Change-Id: I8924ce97ea422ef1e9a5becb5ea2fda3bf77d8cf
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds support for variants to use secondary SPD if
required. This enables a variant to have different types of memory
supported using the same image.
BUG=b:73514687
Change-Id: I3add65ead99c510f2d6ec899fbf2cb9a06c79b0c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Similar to Soraka, this change sets the pch_trip_temp value to
75C. This is important so that PMC can shutdown the thermal sensor
when CPU is in C-state and DTS temp <= pch_trip_temp.
BUG=b:74089135
Change-Id: Ic46fa0681796b821dfb014ab91734c960df7846a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If switch to VT2 on nautilus, screen flicker appears. We found if we
rollback the change of slew rate setting, then the flicker issue will
be gone: https://review.coreboot.org/c/coreboot/+/22588
But nautilus board needs slew rate tuning to reduce EE noise, so we
decided to change only SlowSlewRateForSa to 2 (Fast/8) instead of
rollback the whole change of the CL:22588. It can remove the flicker on
VT2.
BUG=b:71397040
BRANCH=master
TEST=emerge-nautilus coreboot
Change-Id: Id1d4bd8b1316c02c783de708ec4658e030193a26
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/23877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds the Pmax setting in device tree. The Pmax is from
MAX(PL4_sku1, PL4_sku2, ..) + ROPmax. Given ROPmax is 30W and
the maximum PL4 is from U42, hence the Pmax = 71W + 30W = 101W.
BUG=b:72138778
BRANCH=None
TEST=USE=fw_debug emerge-nami chromeos-mrc coreboot chromeos-bootimage
& ensure the Pmax value is passed to FSP-S.
Change-Id: Ief6a134dc5b6bd2b8e07b4a44450e99ff26402d9
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Soraka, Poppy & Nautilus are designed to operate at max power of
45 Watt. Hence set psys_max to 45W.
BUG=b:66066340
BRANCH=None
TEST=Build and boot soraka.
Change-Id: If6f624733830b462329b5f539c20e2aea664143e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/23757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
This change enables DPTF and configures the policy. DPTF parameters were
provided by internal power team.
BUG=b:67877437
BRANCH=master
TEST=emerge-nautilus coreboot
Change-Id: I31b31d5282ab38278bc68045ce75fdc6192f1144
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/23731
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Original SPD provided by the vendor had bytes after 254 shifted by 16
bytes. This change fixes the SPD data based on the latest details
received from the vendor.
BUG=b:72749394
TEST=Verified that the device with this memory part boots to OS fine.
Also, mosys is able to dump the right memory information.
Change-Id: I6938dea761c5785048aad69eeeaf50e2d0fa8ca1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change makes the Nautilus platform update the two fields:
*oem_id* and *oem_table_id*, if the Maxim codec is detected.
Change is made to correct the audio topology file name that is
being read from oem_id fields, loaded and displayed in dmesg.
BUG=b:68686020
TEST=Build, booted nautilus board. Verified kernel reads new strings.
Change-Id: I041f2838f07a2525be7a28fdc69b7f1af46d16f1
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/23648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change makes Nami platform update the two fields:
*oem_id* and *oem_table_id*, if the Maxim codec is detected.
Change is made to correct the audio topology file name that is
being read from oem_id fields, loaded and displayed in dmesg.
BUG=b:70646770
TEST=Verify kernel reads new strings.
Change-Id: I513a997f312e2d37d76da0379feb017d1f591f9a
Signed-off-by: Kaiyen Chang <kaiyen.chang@intel.com>
Reviewed-on: https://review.coreboot.org/23670
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change updates the WiFi device wake pin to GPP_E22 from WAKE# (to
match the latest schematic changes).
Since WiFi was the only device using WAKE# pin, DSX_EN_WAKE_PIN is
removed from deep_sx_config as well.
BUG=b:72697650
TEST=Verified:
1. Wake-on-wifi works.
2. Device is able to enter G3 without WAKE# pin causing unwanted wakes
from deep S5.
Change-Id: Ibde81f73cca322f9b8b45baf8ee18ae00521467d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On EVT, the USB and MIPI cameras share the same power source. As a result,
when the MIPI camera driver turns off the camera once probed, USB camera will
be disconnected. To make USB camera work on EVT devices, we will need a hack in
coreboot to leave the camera power always-on.
BUG=b:72839352
TEST: Verified the MIPI and USB camera function on DUT board
TODO: This power issue will be fixed on DVT build. Will revert this patch
once confirmed power sources for MIPI and USB camera could be supplied
individually.
Change-Id: Icaaf7e17447492f2e2f2d03eb9a35bcc53667f28
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-on: https://review.coreboot.org/23546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andy Yeh
This change selects EC tablet event and provides trip point
temperatures for tablet and non-tablet mode so that DPTF can
be supported depending upon device mode.
BUG=b:65467566
TEST=Verified by changing modes that the trip point temperatures are
updated in the
OS (/sys/devices/virtual/thermal/thermal_zone{2,3,4,5}).
Change-Id: I071868982fa87821550b870a6d8050cf2a030b49
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23463
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This change decouples EC tablet event and TBMC device by guarding
TBMC definition and notification using EC_ENABLE_TBMC_DEVICE. It
allows mainboards to use tablet events without having to define a TBMC
device.
BUG=b:72554519
Change-Id: Ie38b6d68486e8e644dd0d6d406def3ae7fdb5152
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This change updates the camera power enable GPIOs as per the latest
schematics. With this update, since one of the enable GPIOs is using a
UART0 pin, set UART0 to PchSerialIoSkipInit in devicetree so that
FSP-S does not re-configure the UART0 GPIOs.
BUG=b:68964831
Change-Id: I5d9126ed8ca2b714f6276f4d3a24c243d7654774
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change disables SATA controller in order to make SATA IP enter
low power status.
BUG=b:72332817
TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
and verify SATA IP enters low power state
Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
Change-Id: I65173104fce258d03956bbb0e80073c47fe80fab
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Right now the poppy baseboard camera topology allows to add maximum of 2
sensors. The sensors can be of different vendors. The current ASL code
structure doesn't allow sensor customization. Moving PMIC specific objects
from sensor objects to PMIC scope and having separate sensor ASL files will
help in unbinding the PMIC and sensor objects and allow some customizations.
BUG=None
BRANCH=None
TEST=Build and boot soraka, make sure both camera's are working fine
and also verify that the generated DSDT looks fine.
Change-Id: I63ae1a685b78bda212c5c48a4c2dc744164a3cb5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The variant boards can have a custom endpoints, splitting the ASL code
aids customizing the endpoints as per the variant board setup.
BUG=None
BRANCH=None
TEST=build boot soraka, verify that the cameras are working fine and
generated DSDT tables are same as before.
Change-Id: I5f1cded25bfb6a7baf18b211f9773dfecdc2f264
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Digitizer power is not controlled by SoC. Also, since the digitizer
uses I2C-HID driver in Linux kernel, the device is put into sleep
anytime system is suspended. Thus, there is no need to control the
reset gpio using ACPI power resource.
TEST=Verified that digitizer device is properly detected on boot-up
and after suspend/resume.
Change-Id: Id11b8412d0ac48b2701d53b0a22ad3b747b544ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since the current hardware revision does not have external pull on the
pen eject signal, this change adds internal pull-up on it.
Change-Id: I426d9833d7efbd8735b6f2b4896d1012b62cb4b8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tony Lin <tonycwlin@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
