This change does the following:
- Move PCH init code from the common romstage to sb code, this allows
for easier reuse in bootblock
- Provide a common minimal LPC io decode setup, mainboards can
override this in the mainboard_lpc_init if required
- Set up LPC generic IO decode up in romstage based on devicetree
settings
- Remove the ramstage LPC generic IO decode from ramstage as this is
now done in romstage.c
- Get rid of unneeded setup of spi_read configuration in BIOS_CNTL as
this is already done in the bootblock.
Change-Id: I3f448ad1fdc445c4c1fedbc8497e1025af111412
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move the mainboard_romstage_entry to a common location and provide
mainboard specific callbacks.
Change-Id: Ia827053617cead5d2cf8e9f06cb68c2cbb668ca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is based on the sandybridge settings.
The current lookup table comes from the x201 vendor lookup table.
Tested: USB mouse and webcam still work and current registers are the
same as before. USB IR are not but the code follows EDS instead of the
register replay.
Change-Id: Icea9673623a62e7039d5700100a2ee238478abd1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35762
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The values read back in those ranges are identical before and after
this change and the Lenovo Thinkpad X201 still boots fine.
Change-Id: I406510e0573ac97003da7d97181abdfbfd2a872f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35760
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RCBA registers 0x3400-0x3500 are all handled elsewhere
in the code, so no need to have a 'replay' of those.
The remainder now consist of USB setup and undocumented bits
that should likely not be touched at all.
Change-Id: I69fc8a5e16f7cf0e1068d0d2ed678a6c2f6e70a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This does the following:
- implement a PCH disable function that will be called by the PCI
drivers as part of their chip_ops
- removes the iobp_x calls as those don't exist on ibexpeak
- complete the devicetree with to be disabled PCI devices for the
chip_ops to be called
- Clean up some code copied from bd82x6x
Change-Id: I78d25ffe9af482c77d397a9fdb4f0127e40baddc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This properly sets up the chipset initialization registers, instead of
replaying an RCBA dump.
The information is taken from the EDS and from the thinkpad x201
vendor BIOS disassembly and from an HP UEFI.
TESTED on Thinkpad X201. Seems stable at booting, rebooting and resume
from S3.
Change-Id: I21c2beaf70da27dbe6a56e2612df2c257c05fc62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The extra PCI bus RST# and 200ms delay there was workaround
for custom add-on hardware.
Change-Id: I38c4677cfb41d620498be8e0c257b517995bad5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Minimize use of hard-coded value for acpi_table_header->revision to soft
code. Replace with macro defined in arch/acpi.h for FADT and with the
get_acpi_table_revision function for SSDT.
Change-Id: I99e59afc1a87203499d2da6dedaedfa643ca7eac
Signed-off-by: Sourabh Kashyap <Sourabhka@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ONBOARD_MICRON_MEM and ONBOARD_SAMSUNG_MEM are available.
These are used to determine if Samsung or Micron onboard memory is
assembled. This can not detected run-time.
Choice is replaced by one config.
Only oldest HW revision contains Samsung module, so set
CONFIG_ONBOARD_SAMSUNG memory to default No.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: Id65e92bd4b8d4fe3a6b87dec9bf77e3a62e1be96
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
No support is available in mainboard.
Add support to mainboard:
- Add mb_log_list[]
- Add routine mb_crtm()
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: I5120ffb6af0b41520056e1773f63b7b2f34a2460
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The vendorcode for verified boot is uploaded, but not used by a mainboard.
Add support to the mainboard for verified boot.
The items to be verifed are placed in board_verified_boot.c
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701 rev 0-2
Change-Id: I3ea0a95287977df0dea13e05acedd5406538a6ee
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33463
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously all boards using eSPI for the Chrome EC just called it
LPC as the code for the chrome EC is the same between the two
busses.
I'm adding a new Kconfig symbol to specify eSPI, so switch the
boards that actually use eSPI to that symbol and add the LPC
symbol to all the others.
The EC_GOOGLE_CHROMEEC_LPC symbol will no longer default
to enabled for x86 platforms, so one symbol or the other needs to be
specified for each platform.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Icf242ca2b7d8b1470feda4e44b47a2cdc20680f2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Connected 4K monitor is not configured at max resolution. The
framebuffer size is too small.
Increase the framebuffer size to 64MB. This is sufficient for max
configuration of 1 HDMI monitor combined with internal LCD panel.
BUG=N/A
TEST=4K HDMI monitor and LCD working fine on Facebook FBG-1701
Change-Id: I25d2cd696830fc5bda84ea2b87538f526373998e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
PCB version is determined using inb() in actual code.
Create function mainboard_read_pcb_version to read pcb version.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: I7c16627f468d84ca4ad2aab8bf9fb555f50dc23c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The previously provided device path made no difference, all
integrated PCI devices point back to the same chip_info
structure.
Change reduces the exposure of various SA_DEVFN_xx and
PCH_DEVFN_xx from (ugly) soc/pci_devs.h.
Change-Id: Ibf13645fdd3ef7fd3d5c8217bb24d7ede045c790
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Disable memory channel by HW strap pin. Using for factory
debug.
BUG=b:139773082
BRANCH=N/A
TEST=Rework HW strap pin and check /proc/mem_info
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic5f53f0ba3bd432fbcb7513d2a8aa49d42f7a23e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35241
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two fields of struct sdram_params are renamed for future CL of DRAM full
calibration. Field 'impedance' is also removed.
BUG=none
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I2f9673fd5ea2e62ee971f0d81bdd12aaf565e31c
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35738
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the the FSP Parameter PchHdaVcType a devicetree setting and make
use of it in the devicetrees of all boards that currently set it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ibafc3b6bd2495658f2bd634218042ec413a89f5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
A missing definition of gameport base (PNP io 0x60) will cause
an automatic address assignment during PCI/PNP enumeration, which
won't obey limit 0x7ff. This will cause the enumeration to fail
as other devices already have the values enabled.
The symptoms are: not working USB, PS/2, garbled UART console,
not working PCIe GPUs and crashes. Probably because of wrongly
assigned IO ports.
Example of log (shortened):
Done reading resources.
Setting resources...
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.0 1c * [0x0 - 0xfff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.1 1c * [0x1000 - 0x1fff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.2 1c * [0x2000 - 0x2fff] io
!! Resource didn't fit !!
aligned base 400 size 10 limit 2e7
40f needs to be <= 2e7 (limit)
PCI: 00:1f.2 20 * [0x3080 - 0x308f] io
!! Resource didn't fit !!
...
ERROR: PCI: 00:02.0 14 io size: 0x0000000008 not assigned
...
ERROR: PCI: 00:1f.2 10 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 14 io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 18 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 1c io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 20 io size: 0x0000000010 not assigned
...
PCI: 00:1b.0 subsystem <- 8086/27d8
PCI: 00:1b.0 cmd <- 102
PCI: 00:1c.0 bridge ctrl <- 0003
PCI: 00:1c.0 subsystem <- 8086/27d0
PCI: 00:1c.0 cmd <- 107
PCI: 00:1c.1 brids70c01mcu0PeC: 0
dV0i8s0immicrocode: upd10a00000y0025 x666600CPU physiaB 0 0 e k
MTRR cheaeu60zeAttemfWaiting for 1st Sot AP: slot 1 apic_L0ecl0zsax a
aInitiNntt kac:oIG0 Ua dUrSGSGL Ct0C07fintel_vga_int15_h
VGA Option ROM wa7..Azalia0Azalia: codkAbCiPCI: 00:1c.0 init finished
We can see the ports probably started to collide after the activation
of 00:1c.0 device. A debug run with compiled SPEW shows the problem
with enumeration:
PCI: 00:1f.1 18 * [0x50b8 - 0x50bf] io
PCI: 00:1f.2 10 * [0x50c0 - 0x50c7] io
PCI: 00:1f.2 18 * [0x50c8 - 0x50cf] io
PCI: 00:1f.1 14 * [0x50d0 - 0x50d3] io
PCI: 00:1f.1 1c * [0x50d4 - 0x50d7] io
PCI: 00:1f.2 14 * [0x50d8 - 0x50db] io
PCI: 00:1f.2 1c * [0x50dc - 0x50df] io
PNP: 002e.7 60 * [0x50e0 - 0x50e0] io <-- gameport base
DOMAIN: 0000 io: base: 50e1 size: 40e1 align: 12 gran: 0 limit: 7ff done
Notice a weird base for DOMAIN, along with the limit.
Adding a definition of gameport (0x220) as a workaround fixes
the problems.
The gameport should be still disabled thanks to disable bits
(W83627THF datasheet is little bit chaotic). I didn't find any info
if the gameport is available on some pads of the motherboard.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Change-Id: Ie8e42552ac5e638e91e5c290655edcce1f64e408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is a PCI standard register, no need to alias its
definitions under different names.
Change-Id: Iea6b198dd70fe1e49b5dc0824dba62628dedc69a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This also reworks the interface to override OPs from the devicetree to
match the interface in sb/intel/common/spi.
Change-Id: I534e989279d771ec4c0249af325bc3b30a661145
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
To support mt8183 power saving during suspend to RAM, this patch loads
SPM firmware to support SPM suspend. SPM needs its own firmware to do
these power saving in the right timing under correct conditions. After
linux PM suspends, SPM is able to turn off power for the last CPU and do
more power saving for the SoC such as DRAM self-refresh mode and turning
off 26M crystal.
BUG=none
BRANCH=none
TEST=suspend/resume passes for LPDDR4 3200
Change-Id: I3393a772f025b0912a5a25a63a87512454fbc86e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This removes the "ifdef ACPI" which is not needed here as we currently
don't include gpio.h in any asl file.
Change-Id: I803bbee5933eda9423a9bc9fcaea9e905e3ac78e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35543
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes the warning that power_on_after_fail could not be found,
adds a default config and adds the parameter hyper_threading.
Change-Id: I10b0aa71fa7916b01e93e16cbd81e427fd14f6a4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35526
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CONFIG_GBB_HWID can be generated automatically now so we can remove
the test-only HWIDs set in board config files.
BUG=b:140067412
TEST=Built few boards (kukui, cheza, octopus) and checked HWID:
futility gbb -g coreboot.rom
Change-Id: I4070f09d29c5601dff1587fed8c60714eb2558b7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35635
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: Iee12a5d1781c869b20bc14a52ecbf23474caa3fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cometlake pch EDS vol1 section 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on drallion platform, able to boot up into OS and stay
at power up state.
Change-Id: Idd1befeb14a251b7c0542ca1f99049d07b28fb98
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Per google/stout.
Tested with SanDisk SSD U110.
Change-Id: I7cc9837f572236acac2007e95990e64c25a5d6e2
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Based on schematic and register dumps.
Change-Id: I91fc47022988cfe986fb8c1ed21dc073ee7d16bc
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The vendor id option set here is useless as most SSVID registers get
filled with 0x8086 (their VID) by default, anyway.
Besides that the Kconfig option isn't meant for retrofit ports, cf.
commit 7e1c83e31b (Add Kconfig options to override Subsystem Vendor and
Device ID). The right place would be the devicetree.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If67c679bb342f63096902535734106e4f1651118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Most of the X11 boards with socket LGA1151 are basically the same boards
with just some minor differences like different NICs (1 GbE, 10 GbE),
number of NICs / PCIe ports etc.
There are about 20 boards that can be added, if there is a community for
testing.
To be able to add more x11 boards easily like x11ssm (see CB:35427) this
restructures the x11ssh tree to represent a "X11 LGA1151 series". There
were multiple suggestions for the structure like grouping by series
(x10, x11, x...), grouping by chipset or by cpu family.
It turned out that there are some "X11 series" boards that are
completely different. Grouping by chipset or cpu family suffers from the
same problem. This is why finally we agreed on grouping by series and
socket ("X11 LGA1151 series").
The structure uses the common baseboard scheme, while there is no "real"
baseboard we know of. By checking images, comparing logs etc. we came to
the conclusion that Supermicro does have some base layout which is only
modified a bit for the different boards.
X11SSH-TF was moved to the variants/ folder with it's gpio.h. As we
expect the other boards to have mostly the same device tree, there is a
common devicetree that gets overridden by each variant's overridetree.
Besides that some very minor modifications happened (formatting, fixing
comments, ...) but not much.
Documentation is reworked in CB:35547
Change-Id: I8dc4240ae042760a845e890b923ad40478bb8e29
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35426
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify IRQ pin from D21 to A21 and support wake-up from touchpad
BUG=b:141519690
TEST=build bios and verify elan touchpad works fine
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6cc5b780ffcee24f1f2a04e88c30628ceb5904e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35551
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
new DDR particle:
1. Samung K4A8G165WC-BCWE
2. Hynix H5AN8G6NCJR-XNC
BUG=b:139085024
BRANCH=master
TEST=rework new source to DUT and re-flash bios to DUT and
verify DUT will bring up successfully
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I0d039af53938086733308a081a77a7398e7bf5d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the configuration 'Juniper' for the new mainboard.
BUG=b:137517228
TEST=make menuconfig; select 'juniper' and build
Change-Id: I94e3ac7f6de3fecf177e344cb217eaecf6362d69
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All variants of hatch are using Comet Lake and so the selection can be
done in Kconfig without requiring each variant to do the same.
Change-Id: Ief34296334ede5ba0f5f13381e92427ccc440707
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Sort the names of all variant mainboards in an ascending order.
Change-Id: I19d502298744c0e0cbc91eb836c62ca90cdb9a5c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: I3d58094256d2730dbd249291a8f1ed8df9dfe62d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The implementation of udelay() with LAPIC timers
existed first, as we did not have calculations
implemented for TSC frequency.
Change-Id: If510bcaadee67e3a5792b3fc7389353b672712f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34200
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Razer Blade Stealth H2U is a KabyLake System using:
- Intel KBL 7500U
- ITE8528E SuperIO
- Intel 600P Series NVMe SSD
- Either four MT52L1G32D4PG (16GB) or MT52L512MB32D4PG (8GB)
of soldered memory in dualchannel mode
- (Optional) Touchscreen
- HDMI 2.0a via DP-1: Paradetech PS175
- AlpineRidge Thunderbolt 3 controller
- TPS65982 USB-PD power switch / multiplexer
Even though it has a 16MB chip equipped (W25Q128.V) only the first 8MB
are used and mapped via IFD. The rest is left empty (0xFF). The flash is
not secured in any way and can be read via flashrom. It should be the
source for this port's IFD and ME blobs.
Working:
- USB-A Ports left and right
- Speakers
- Touchscreen (USB)
- Onboard Keyboard in Linux
- NVMe SSD
- SeaBIOS, Tianocore and Grub Payloads
- Webcam
- Powersaving Modes
- Battery state and LID switch, sometimes slow to update.
- Touchpad (I2C-HID)
- Headphones
Not part of this commit:
- Thunderbolt / USB-C (Requires advanced EC signaling)
- Full HDMI support (Currently requires plugged connection at boot)
Change-Id: I7ede881d631e1863f07f5130f84bc3b8ca61a350
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Disable root port IOU0 to which built-in NIC is attached.
TEST=on OCP monolake, hide built-in NIC and make sure OS does not report
built-in NIC
Change-Id: I2384e7dd073355f0ced2902ac2d8418996b1c5aa
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
- configure DMA fw_cfg
- add support to read using fw_cfg_dma
- provide fw config version id info in logs
BUG=N/A
TEST=Build and boot using qemu-i440fx.
Change-Id: I0be5355b124af40aba62c0840790d46ed0fe80a2
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fill the dimm info struct to make SMBIOS type 17 appear.
TESTED=Up Squared
Change-Id: I4de63362c8fea8a886594cdcf0eec48421afb605
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34564
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop unused CNF2_LPC_EN, as there is no device which uses IO 0x4e/4f.
Do not use the mainboard model to set COMA_LPC_EN. Make use of
NO_UART_ON_SUPERIO instead, as it is more future-proof.
Change-Id: Iac49250b0f509a42012f82db8aa85ba85559c66f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
BUG=b:140545732
TEST=build bios and spd index set to 6, verify DUT bring up normally
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I337b0bdcd37a9c4baacccbc6786968031a41b31e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35511
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CdClock does not need to be set because the board does not use IGD.
Change-Id: I6835ccdf80530f9efc6fdeb0363dcf9267f99d21
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Implement Locator and Bank fields (as reported by dmidecode) to match
vendor BIOS.
TEST=on OCP monolake, run dmidecode tool and see that "Locator" field
matches expectation.
Change-Id: Ia271ff1e596ba469cf42e23d8390401c27670a27
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The specified CBFS_SIZE does not make sense.
The boards BIOS region is 0xb00000. Correct the value.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia3014c7fd081030607790ced6bb55323086f1161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35458
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A closer read of the EDS indicates that when GPIO Driver mode is
selected, GPIO input event updates are limited to GPI_STS only.
GPI_GPE_STS updates are therefore masked, and we don't want to enable
this behavior. It masks the GPE and does not allow us to see this GPE
as a wake source, obscuring the reason that the system woke up.
Also switch the IRQ from level-triggered to edge-triggered,
otherwise the system will auto-wake from any sleep state when the
pen is ejected from the garage.
BUG=b:132981083
BRANCH=none
TEST=Wake up system from S0ix using pen eject, verify that mosys
eventlog shows GPE#8 as the S0ix wakeup source. Wake up system from S3
via pen eject, and verify that the wakeup source shows as GPE#8.
Change-Id: If017e12e23134f5cfed7cbb6047cc9badd9bf7e8
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35459
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implementing logic base on sensor detection to determine SKU id.
BUG=b:140472369
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5e71ae6b97378b78055735bbf4b6b55ffe38b978
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35366
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initialize the input_hertz and uart_pci_addr fields of the lb_serial
struct to prevent later undefined reads in lb_add_serial(). This was
done for exynos5420 in commit ff94e00362 (soc/samsung/exynos5420/uart.c:
Init new serial struct variables), and this patch finishes the rest.
Note that not all of the drivers can have the UART PCI address
configured at build time, so a follow-up patch will be needed to correct
those ones.
Change-Id: I733bc8185e2f2d28a9823495b53d6b09dce4deb1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1354778
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34548
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add DPTF based thermal control for ambient sensor for CML based
Helios system. Also, update other sensor names information.
BUG=b:139335207
BRANCH=None
TEST=Build and Boot on Helios board and check all sensor details.
Change-Id: I322d53536fbdf6db70f5a24afb322d9f206eaeac
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update DPTF thermal temperature threshold values for CML based
Helios system. This updates CPU active cooling temperature
threshold to appropriate values which addresses the issue of
running the Fan at lower CPU temperature as per bug.
Also, added active cooling temperature thresholds for other
TSR sensors.
BUG=b:141087272
BRANCH=None
TEST=Build and boot on Helios board to check the fan functionality.
Change-Id: I5c8502f8c9e6121c18024d2a8d5a4f7680797b8d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35446
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no board named X11SSH+-TF.
Change-Id: Ide01a8d59c09747dfe7d59fd9e17bd5194fb14e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Add SKU#18 to config power sequence below:
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:134854577,b:137033609
BRANCH=octopus
TEST=build
Change-Id: I58e07518f6daaf608684c9fa1b1c88fc592ea117
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds SPD files for Drallion. Use spd_index
matrix to correspond mem_id. This can save the dummy spd index
to reduce the size of SPD.bin.
BUG=b:139397313
TEST=Compile successfully
Change-Id: I2f7e75fdbca4183bcd730e40fef4bfe280ab900b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35346
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some T430s variants have a Thunderbolt controller wired to PCIe port
The controller hotplugs itself to the chipset when a downstream device
is hotplugged into it, so the hotplug capability should be enabled on
PCIe port #5.
TODO: find the correct gpio pin to detect the Thunderbolt controller
at runtime.
There are 3 variants of mainboard for Thinkpad T430s: Basic type
(Wistron LSN-4 11263-1), Boards with an additional discreet GPU,
Boards with an additional TB controller (Wistron LSN-4 11271-1),
each of which has a different schematic.
The gpio27 on the last type is set as set as GPIO-INPUT, compared
with GPIO-OUTPUT-HIGH on the basic type boards.
Change-Id: I61f41db100f398069e50e2da8a378b3a8d1c84bf
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This Kconfig symbol is set at a default of 36 in cpu/x86 and is now
only used in the romcc bootblock to set up caching to upgrade the
microcode. It's not mainboard specific.
Change-Id: I29d3a8308025e586a823603f8d6edafd30cb9d95
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and ATF(BL31) can get this parameter.
Change-Id: Iefa70dc0714a9283a79f97d475b07ac047f5f3b0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This change overrides USB port settings for kohaku.
Some port settings are same with baseboard, but I'd like to describe all
settings here to be aware of current setting and usage of USB ports on
kohaku.
BUG=none
BRANCH=none
TEST=built and measured SI of USB ports internally
Change-Id: I5ac05485d1cd94416e5a0aecf7fa6769bd7c9e84
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Information based on superiotool dump.
Change-Id: I24ae9b1a7eab3095518341354544efe613912a6a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enables and configures GPIOs in the NCT6791D chip. The values for
registers taken from the superiotool dump.
Change-Id: I5968a6c20cc013697d64bfbe4fc2e7b2390b72b0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch uprevs the Arm Trusted Firmware submodule to the new upstream
master (commit 42cdeb930).
Arm Trusted Firmware unified a bunch of stuff related to BL31 handoff
parameters across platforms which involved changing a few names around.
This patch syncs coreboot back up with that. They also made header
changes that now allow us to directly include all the headers we need
(in a safer and cleaner way than before), so we can get rid of some
structure definitions that were duplicated. Since the version of entry
point info parameters we have been using has been deprecated in Trusted
Firmware, this patch switches to the new version 2 parameter format.
NOTE: This may or may not stop Cavium from booting with the current
pinned Trusted Firmware blob. Cavium maintainers are still evaluating
whether to fix that later or drop the platform entirely.
Tested on GOOGLE_KEVIN (rk3399).
Change-Id: I0ed32bce5585ce191736f0ff2e5a94a9d2b2cc28
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
drallion_ish.bin is updated for drallion GPIO changes
and not compatible with arcada_cml.
TEST=Build and boot arcada_cml
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Change-Id: Idb35c33425bfd50533df74349dd645db18a65bc5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Even though GT7375P programming guide rev0.4 only requires a reset delay
of 120ms, in practice, we have to increase the reset delay to 500ms, or
Goodix FW update would fail.
This is a workaround. In the long run, we hope Goodix can fix the power
sequence in touch firmware.
BUG=b:138795891, b:138796844
TEST=boot helios board and verify Goodix FW update succeeded
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Ic0049bf240de0a1c7f1b1f39bf155d48bb76fb86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35350
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will increase ME region size and reduce the BIOS region size.
BUG=b:140665483
TEST='compile successfully'
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5be2580d280569421d0870a06f9b93124b564b6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35304
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PchPwrOptEnable FSP UPD is for internal testing and not really available
in externally released FSP source hence assigning this UPD using devicetree
config dmipwroptimize doesn't do anything.
TEST=Build and boot sarien/arcada.
Change-Id: I6da2a088fb697e57d12008fa18bd1764b3da7765
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
With the current devicetree the kernel doesn't provide any serial
after serial init.
Update the devicetree to resolve this issue.
Tested on HiFive Unleashed.
Change-Id: I4427d34a12902e0eaa2186121a53152b719cadff
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Drallion uses the same touch panel as Sarien. Copy the deivce
from Sarien.
BUG=b:140415892,b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8e6d2dcf4bd2ed2325137a05811af03692d40342
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35305
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MT8183_DRAM_EMCP is enabled for devices using eMCP to run at a high DRAM
frequency (e.g., 3600Mbps).
BUG=b:80501386
BRANCH=none
TEST=Memory test passes on EMCP platform
Change-Id: Icf875427347418f796cbf193070bf047844d2267
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34433
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setup EC_PCH_ARCORE_INT_L, tied to GPP_D17, and define as EC_SYNC_GPIO..
- change GPP_D17 definition to PAD_CFG_GPI_APIC_INVERT as
EC_PCH_ARCORE_INT_L is active low
- add EC_SYNC_GPIO to the group of chromeos_gpios for use by depthcharge
BUG=b:139384979
BRANCH=none
TEST="emerge_nocturne coreboot depthcharge chromeos-bootimage",
flash & boot nocturne in dev mode, verify that volume up and down
buttons work in the dev screen and that the device boots properly into
the kernel.
Change-Id: Ia43c622710fde8686c60b836fb8318931d79eb61
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
pull in the FPU VDDIO turn on to fix the power leakage problem
on FPU VDDIO and FPU CS during power on sequence.
BUG=b:138638571
BRANCH=none
TEST=emerge-hatch coreboot chromeos-bootimage
Signed-off-by: Frank_Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I3f6bf3676922e987c2e282b697a2333e2d90289e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tune I2C bus 1, 2 and 3 clock and make them meet spec.
BUG=b:140665478
TEST==flash coreboot to the DUT and measure I2C bus 1,2,3 clock
frequency less than 400KHz
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6b2a51a866e57d13fe528452e4efdcf17a72317f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35298
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. SKU1 for eMMC
2. SKU2 for SSD
BUG=b:140008849, b:140573677
TEST=Verify SSD is disabled when SKU ID = 2/4/21/22
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I827e6f1420801d43e0eb4708b8b8ad1692ef7e9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35204
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From DDR4 SPD spec:
Byte 4 (0x004): SDRAM Density and Banks
Bits [7, 6]:
00 = 0 (no bank groups)
01 = 1 (2 bank groups)
10 = 2 (4 bank groups)
11 = reserved
Bit [5, 4] :
00 = 2 (4 banks)
01 = 3 (8 banks)
All others reserved
Separate DDR3 and DDR4 banks. And extened capmb, rows, cols and ranks.
Separate DDR3 and DDR4 ORGANIZATION/BUS_DEV_WIDTH offset.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5f56975ce73d8ed2d4de7d9fd08e5ae86993e731
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on HW schematic to modify USB setting.
Drallion has two type C on left and two type A on right.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I925de209635d92ef61ccb9114efebb4b10f30e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Sets all unused sata ports to disable in the device tree
Note:
SATA4 and SATA5 are located at the bottom of the board, but there
is no connector for this. Apparently, a board with an increased
number of ports is very rare. Perhaps this is a separate variant
of the Asrock motherboard. For this reason, these ports are also
disabled
Change-Id: I5b3ad372f1d6607cc7b4a78e3c59d2a5ae1d2cf5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable spi0, i2c0 and i2c1 in the “SerialIoDevMode” register for the
following reasons:
1. when the AMI BIOS is used, these pci devices are disabled in
lspci.log;
2. there are no pads in the inteltool.log that use the functions of
these buses
Change-Id: I01ab10eb3fd41e81a1726805247c2b472d72287c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35070
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The string "register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" was mistakenly
taken from the Intel KBL-RVP8 devicetree.cb. Remove it, since the i2c4
bus is disabled in the "SerialIoDevMode" register
Change-Id: I44ecd5c22efd66b02a2851dc14a1a95421f39a71
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1) VR domains current limit Icc max for Sky/Kaby Lake S is set based
on the processor TDP [1]. Updates information about this
2) Sets VR voltage limit to 1.52V, as described in the datasheets [2,3]
[1] Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
[2] page 112-119, 6th Generation Intel(R) Processor Families
for S-Platforms, Volume 1 of 2, Datasheet, August 2018.
Document Number: 332687-008EN
[3] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I6e1aefde135ffce75a5d837348595aa20aff0513
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Based on HW schematic to modify PCIE setting.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia744a6f3cba76c507c1c43b0a981cb6d89c1a40f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Use sku-id to load the SAR values for Bloog device.
BUG=b:138180187
BRANCH=octopus
TEST=build and verify load Bloog SAR by sku-id
Cq-Depend: chromium:1771477
Change-Id: Id0bc2609fd1c4eaeb380f8f1532ab30d34e2aeb3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To avoid possible panel failures due to incorrect timing settings for
PTN3460, the internal graphic device should be disabled.
Change-Id: Ie0b9ed99fb78461bb48d6f2ff328643cd8c2cd15
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Rename the table from Liara specific to simply specifying
that it's using 2T command rate
BUG=139841929
TEST=build and do stress test
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6e10b95c8aea50e68d8a3b710f30dda4f6b807d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
override 'uint32_t sku_id(void)' so that lib_sysinfo.sku_id get a
correct value in depthcharge
BUG=b:140010592
BRANCH=none
TEST=boot treeya board, in depthcharge stage, lib_sysinfo.sku_id
print correct value.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I631f62021e8104a69a43667a811c9c23e3105596
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Magf - <magf@bitland.corp-partner.google.com>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Padmelon board code was written for Merlin Falcon (family 15h models 60h-6fh),
but as the needed binaries are not yet merged (commit 33615), a config
HAVE_MERLINFALCON_BINARIES was added. If the binaries are not available,
the board defaults to Prairie Falcon, which use the same binaries as Stoney
Ridge. Once the binaries are merged, the config will be eliminated. Fan
control is done through F81803A SIO, and IRQ/GPIO and other board
characteristics are the same regardless of Merlin Falcon or Prairie Falcon.
Padmelon board was created to accept Prairie Falcon, Brown Falcon and Merlin
Falcon. The requested development was for Merlin Falcon. There are some small
spec changes (such as number of memory channels) between SOCs. Brown Falcon
was not investigated, Prairie Falcon is very similar to Stoney Ridge.
Started from Gardenia code, added changes created by Marc Jones and finally
revised against schematic, which added changes to GPIO settings.
BUG=none.
TEST=Both versions tested and boot to Linux using SeaBIOS.
Change-Id: I5a366ddeb4cfebd177a8744f6edb87aecd4787dd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Select NO_UART_ON_SUPERIO as the SoC internal UART is used.
The current code is working, so this is just a cosmetic fix to remove
some unused options from Kconfig.
Change-Id: I206557c397da74b572e669feb1e38f0c8473d0d9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35151
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drallion will use soldered down memory and use
GPP_F12 to GPP_F16 indicates mem_id.
BUG=b:139397313
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib5ada54fd2b8f358b59de8089e5405cf3e34825a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Its entirely no-op and is getting in the way of real hardware timers for
power9/talos ii.
Change-Id: I2d21d4ac3d1a7d3f099ed6ec4faf10079b1ee1d1
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35082
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per GT7375P programming guide rev0.4, we want to enforce a delay
of 120ms after the reset is completed, before HID_I2C starts.
BUG=b:140276418
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Id69a9db996bcd9001ef850c50898fbd55327b4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Summary:
This patch calls monolake board specific function to query
settings stored in VPD binary blob to configure FSP UPD
variable HyperThreading.
Test Plan:
* Build an OCP MonoLake coreboot image, run following command
to initialize RW_VPD and insert HyperThreading key:
vpd -f build/coreboot.rom -O -i RW_VPD -s 'HyperThreading=0'
* Flash the image to MonoLake, boot and observe following
message in boot log:
Detected 16 CPU threads
If RW_VPD partition does not exist, or if HyperThreading
key/value pair does not exist, the boot log has:
Detected 32 CPU threads
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I799d27734fe4b67cd1f40cae710151a01562b1b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Remove duplicated code and instead use the IPMI KCS driver, which provides
the same functionality.
Change-Id: I419713c9bef02084cca1ff4cf11c33c2e3e8d3c1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 [1]
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The pad configuration in this patch was
generated using the pch-pads-parser utility [2]. The inteltool dump
before and after the patch is identical (see notes)
Notes:
1. For some reason, GPIO RX State (RO) for the GPP_F4 and GPP_G10
changed the value to 0, but this doesn't affect the motherboard
operation. Perhaps this is because PAD_CFG1_GPIO_DRIVER is set to
PAD_CFG_GPI_INT(), and the pad is not actually connected. So far I
haven't circuit diagram to check this out.
2. According to the documentation [1], the value 3h for RXEVCFG is
implemented as setting 0h.
3. If the available macros from gpio_defs.h [3] can't determine the
configuration of the pad, the utility [2] generates common
_PAD_CFG_STRUCT() macros
[1] page 1429,Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 2 of 2,
February 2019, Document Number: 332691-003EN
[2] https://github.com/maxpoliak/pch-pads-parser/tree/stable_1.0
[3] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
Change-Id: I01ad4bd29235fbe2b23abce5fbaaa7e63c87f529
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add support for the X11SSH-TF which is based on Intel KBL.
Working:
* SeaBIOS payload
* LinuxBoot payload
* IPMI of BMC
* PCIe, SATA, USB and M.2 ports
* RS232 serial
* Native graphics init
Not working:
* TianoCore doesn't work yet as the Aspeed NGI is text mode only.
* Intel SGX, due to random crashes in soc/intel/common
For more details have a look at the documentation.
Please apply those patches as well for good user experience:
Ica0c20255f661dd61edc3a7d15646b7447c4658e
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Change-Id: I2edaa4a928de3a065e517c0f20e3302b4b702323
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Adjust CID to allow for Windows driver to attach without breaking
functionality under Linux. Same change made as to google/cyan
(which uses same Realtek RT5650 codec) in commit 607d72b.
Test: build/boot Windowns 10 on google/buddy, observe audio
drivers correctly attached to codec and Intel SST devices.
Change-Id: I839acc8427ee9b5c425885858a513e9b0b9d0f93
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Drallion will change debug port UART from 2 to 0. Followed HW
schematic to modify it.
BUG=b:139095062
BRANCH=N/A
TEST=Build without error
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib2bcded8de3c9fb2c0a4ccbd002b1f219bccceb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Enable acoustic noise mitgation for hatch platform, the slow slew rates
are fast time dived by 8 and disable Fast PKG C State Ramp(IA, GT, SA).
BUG=b:131779678
TEST=waveform test and reduce the noise level.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I49e834825b3f1e5bf02f9523d7caa93b544c9d17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This removes the need to select ARCH_ARM in SOC Kconfig
Also don't define the default as this result in spurious lines in the
.config.
Change-Id: I1ed4a71599641db606510e5304b9f0acf9b7eb88
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31313
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current HWID for drallion is reported as invalid by chrome, generate
new valid HWID with the following command and taking last 4 digits.
`printf "%d\n" 0x$(crc32 <(echo -n '$1'))`
BUG=b:140013681
Change-Id: I410d37fc3f3372e9420d674b65f2c9a704b670f2
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
