This patch adds MAINBOARD_HAS_NATIVE_VGA_INIT_TEXTMODECFG to the
gigabyte/ga-g41m-es2l Kconfig to allow selecting between textmode and
vesamode in menuconfig.
Change-Id: I84b61118fa0419d49d2498b66029711cdce97576
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16501
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Maxim98357a speaker amp requires BCLK & SFRM to be active
and stable before it is unmuted. If there is a BLCK and no
SFRM, it results in a pop sound.
sdmode_delay property already exists which facilitates this
configuration. This patch updates "sdmode_delay" to avoid
pop sound.
BUG=chrome-os-partner:58356
BRANCH=None
TEST=while audio playback via headset, remove headset.
Audio will be switched playback to speaker. Observe if
pop sound comes from speaker.
Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/16933
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Some PVT units encountered DRAM calibration failure during
power on/off tests. The failure is caused by higher impedance
of the DRAM on those units. So increase the driving strength
for 4GB DRAMs.
BUG=chrome-os-partner:57392
TEST=run cold reboot 100 times on PVT units which have DRAM
calibration issue.
Change-Id: I8a329093db3f1def566e4b7afec3c4f4bfe44c6a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf1aa5ade856af433fa056f51a20d18553ae241d
Original-Change-Id: I0d1776cd1a5892d1f82e9bf414620d1ef6d29132
Original-Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/394451
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Pin-Huan Hsu <ph.hsu@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/16917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5
Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/390615
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16911
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
commit 028200f7 - x86/acpi_device: Add support for GPIO output polarity
updated ACPI_GPIO_OUTPUT to ACPI_GPIO_OUTPUT_ACTIVE_HIGH for the other
boards that needed it, but pyro wasn't in the tree when it was initially
pushed. Now that pyro is in the tree, it needs to be updated as well.
Change-Id: I617999b06ee584e0543d7ae3232bb2be2ff7429c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16930
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
GPIO1_B3 (WLAN_MODULE_RST#) defaults as a pull-up input, but it is also
"pulled up" by 1.8V_WLAN. However, 1.8V_WLAN remains low for some time
during early boot. This leaves the signal floating somewhere in the
middle.
This has two potential issues:
(1) we're leaking some power for some (hopefully) short period of time
(2) we are possibly screwing with the Wifi power sequence; we aren't
supposed to deassert PDn (i.e., MODULE_RST#) until all the rails
have fully ramped for some period of time
Neither of the above issues are likely to be significant, but it is nice
to fix, I expect.
BRANCH=gru
BUG=chrome-os-partner:54026
TEST=measure WLAN_MODULE_RST# on scope at boot time
Change-Id: Ia6af9ad6954ad8feeda33015e3f205842380939e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0e890a2787bf034d3358a33fc88c2dd8078593ab
Original-Change-Id: I120e26ad0ca486a326874986e142dcaee965b62d
Original-Signed-off-by: Brian Norris <briannorris@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/388009
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16882
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
PHY_PER_CS_TRAINING is being enabled when DDR frequency >= 666.
For per cs training, the controller should consider the PHY
delay line switch time and there should be more cycles to
switch the delay line, so update the W2W_DIFFCS_DLY_ value
from 0x1 to 0x5.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: I00df2d4724b0b77f3e7565809fb35bbd2ff01ea5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c135ea3e33d810ed322d947eb8d512d1ac119cfc
Original-Change-Id: I81b99cbc085769b7028e770509d79bd8d550820b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387506
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16721
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
To save power when entering suspend, gpios 2 to 4 need to be set
to input and 'pull none' mode.
Pass the APIO configuration to ATF so it can do a proper job here.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=run suspend_stress_test on kevin board
Change-Id: Id57fe8f622ae3f9c2bc7e58be89518b2b846cd37
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c42082d1ca9a6baa735821382d3e83c1f8dc9ad
Original-Change-Id: Iaf441e8e34c5591ffe7c65f6533fcf0b733ff5ac
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/378475
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16720
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We need to disable some regulators when the device goes into suspend.
This means that we need to pass some gpios to bl31, and disable these
gpios when bl31 runs the suspend function.
BRANCH=None
BUG=chrome-os-partner:56423
TEST=enter suspend, measure suspend gpio go to low
[pg: also update arm-trusted-firmware to match]
Change-Id: Ia0835e16f7e65de6dd24a892241f0af542ec5b4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0f3332ef2136fd93f7faad579386ba5af003cf70
Original-Change-Id: I03d0407e0ef035823519a997534dcfea078a7ccd
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/374046
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16719
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Create the initial Pyro variant which refers to the Reef.
Pyro is APL Chrome board that deviate from reference board Reef.
BRANCH=master
BUG=None
TEST=Build
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: I9beed1f6895e8891d3d51b563edfe172f566718b
Reviewed-on: https://review.coreboot.org/16855
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since there's currently a limitation in coreboot's code that prevents
more than 4KB to be used by the eventlog anyway, this patch shrinks the
available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove
prudent later if we ever resolve that limitation, so that tools can rely
on the area in the FMAP being the same as the area actually used by the
read-only firmware code on these boards.
BRANCH=gru
BUG=chrome-os-partner:55593
TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a
reboot loop to exhaust eventlog space, confirmed that the shrink code
kicks in as expected before reaching 4KB.
Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18
Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We found some boards are not stable when sdram is run at 933Mhz.
Before we can fix it, we need to lower the sdram frequency to 800MHz.
In this patch we modify the DQS delay from 0x280 to 0x260 and extend
the DQS window.
BRANCH=None
BUG=chrome-os-partner:56940
TEST=Booted Kevin.
Change-Id: I68561c4aa4d9ab66acfa3515a42d696157aff759
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 877a7f6ad22a5bde9f9e458bcb65f133f2f001bd
Original-Change-Id: I5eab6bbe96f0dae095c5353403292022e7a25421
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382724
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16709
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add lpddr3-K4E6E304EB-2GB-1CH memory configuration for rialto.
BUG=chrome-os-partner:56759
BRANCH=none
TEST=Build
Change-Id: I698fe450d48b64a06232aa44ecf91d688d9dc17a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d3edecdb135939c3264ab1b831e7821d3a3e0149
Original-Change-Id: I7dae9fd822abeff5b08de0ab9262e1817ac58531
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/380443
Original-Commit-Ready: Alexandru Stan <amstan@chromium.org>
Original-Tested-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Jonathan Dixon <joth@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16699
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Due to different LCD panel requirements the delay between LVDS becomes
active and the backlight is switched on needs to be increased to 500 ms.
Change-Id: I09029624469aef412141c7b46224d48557ba4af1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16875
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Several of the special function pins we're using in firmware have a
pre-assigned pull-up or pull-down on power-on reset. We don't want those
to interfere with any of the signaling we're trying to do on those pins,
so this patch disables them.
Also do some house-cleaning to group the bootblock code better, and
change the setup code for all SPI and I2C buses to first initialize the
controller and then mux the pins... I assume this might be a little
safer (in case the controller peripheral has some pins in a weird state
before it gets fully initialized, we don't want to mux it through too
early).
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I4d5bd3f7657b8113d90b65d9571583142ba10a27
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f8f7fd56e945987eb0b1124b699f676bc68d0560
Original-Change-Id: I6bcf2b9a5dc686f2b6f82bd80fc9a1a245661c47
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382532
Reviewed-on: https://review.coreboot.org/16711
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Increase the SPI bus speed to speed up boot time. The maximum supported
speed at 1.8V is 37.5MHz, and 33MHz is the next lowest convenient speed,
given the clock parents.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. Total time
spent on reading from SPI reduces from 185ms to 141ms.
Change-Id: I71436c9e343b18360fa63d528dea5cfcfbc831e6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7576f6e53e407af61160be142c3d589e864a8cf
Original-Change-Id: I55a19f523817862e081d23469e94fd795456dd67
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381313
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16708
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If we setup the PWM _after_ the pinmux then there's a period of time
when we're driving the PWM incorrectly. Let's setup the regulator and
_then_ configure the pinmux.
This fixes no known bugs, but it is more correct and probably makes the
signals look better at bootup.
BRANCH=None
BUG=None
TEST=scope
Change-Id: I311c0eded873b65e0489373e87b88bcdd8e4b806
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fcf4d0ba29d82cce779c0b25ead36de4a95d97a1
Original-Change-Id: I5124f48d04a18c07bbd2d54bc08ee001c9c7e8d1
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381592
Original-Reviewed-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16700
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Kconfig symbols of type bool are ALWAYS defined, so this code was
always being included and run, which isn't what the author wanted.
Change to use IS_ENABLED(), and a regular if() instead of an #ifdef.
Change-Id: I72623fa27e47980c602135f4b73f371c7f50139b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Everybody knows WHAT they're supposed to do with options, so the text
"Pick this" or "Select to" are redundant.
Change-Id: I327c5be755373e99ca0738593bd78e1084d4d492
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16838
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Replace the use of the old device_t definition inside
mainboard/biostar/am1ml.
Change-Id: Iba2fff5617c62152355b54e446517ad36108aa31
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16688
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch increases the CPU specific passive temp. trip point
and critical temp. trip point value for DPTF policy.
BUG=chrome-os-partner:57903
TEST=Built, booted on reef and verified this passive and
critical temp. trip points with heavy workload.
Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/16766
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
For all mainboard variants use the "Google_Reef" family by default
which is populated in SMBIOS tables. A variant can provide their own
value if needed, but "Google_Reef" can reside as the family without
having to add conditions for each variant when MAINBOARD_FAMILY
have to be overridden.
BUG=chrome-os-partner:56677
Change-Id: Ic214eae1e6473b32f4cb442c09c34355357e1257
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16813
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
These default values weren't being set with the default
keyword so were ending up with different values.
from the default generated config file before this change:
CONFIG_DRIVER_TPM_I2C_BUS=0x9
CONFIG_DRIVER_TPM_I2C_ADDR=0x2
CONFIG_DRIVER_TPM_I2C_IRQ=-1
Change-Id: I19514d0c9b2a9b7e479f003a4d3384e073f4d531
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16828
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Because these variables had "non-hexidecimal" defaults, they
were updated by kconfig when writing defconfig files.
Change-Id: Ic1a070d340708f989157ad18ddc79de7bb92d873
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16827
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add PCI device id to native graphic init and add the Native graphic init
option in Kconfig.
Change-Id: I136122daef70547830bcc87f568406be7162461f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16512
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Switch from FSP 1.1 to FSP 2.0 as the default build.
BRANCH=none
BUG=None
TEST=Build and run on Galileo Gen2
Change-Id: Icbb3a36cdde68baf4d68fbfc371f8847c56e1162
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16810
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add Kconfig values to select the FSP setup:
* FSP version: 1.1 or 2.0
* Implementation: Subroutine or SEC/PEI core based
* Build type: DEBUG or RELEASE
* Enable all debugging for FSP
* Remove USE_FSP1_1 and USE_FSP2_0
Look for include files in vendorcode/intel/fsp/fsp???/quark
BRANCH=none
BUG=None
TEST=Build FSP 1.1 (subroutine) and run on Galileo Gen2
Change-Id: I3a6cb571021611820263a8cbfe83e69278f50a21
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16806
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
pcm205401 is CPU board equipped with T40R of AMD. We used SeaBIOS and
Windows Embedded Standard 7 to test pcm205401.
In comparison to pcm205400, only VGA PCI ID is changed and board
identifier strings in SMBIOS / DMI.
Change-Id: I6c7e90db84f13ffbf9e629f2b92649895a466155
Signed-off-by: Yuichi Ito <yui.corebt@gmail.com>
Reviewed-on: https://review.coreboot.org/15930
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
pcm205400 is CPU board equipped with T56N of AMD. We used SeaBIOS and
Windows Embedded Standard 7 to test pcm205400. I disable the port5,
6, and 7 of the PCI-e in elmex/pcm205400/PlatformGnbPcieComplex.h.
I disable the audio capabilities at the 236th line of
elmex/pcm205400/platform_cfg.h. Coding style is modified to avoid the
error and warning that occur when I commit.
Change-Id: I77cb76903fe3c1b500a306426f5399936382695b
Signed-off-by: Yuichi Ito <yui.corebt@gmail.com>
Reviewed-on: https://review.coreboot.org/15929
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add the 'probed' flag to the touchpad and touchscreen devices so they
are probed by the kernel before being loaded, in case they do not exist
or are replaced with another vendor.
BUG=chrome-os-partner:57686
Change-Id: I0a61964e6874cd99fab0c21fa404a43548fc8ab5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16743
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a header file to provide common declarations that the
mainboards can use regarding EC init.
BUG=chrome-os-partner:56677
Change-Id: Iaa0b37eff4de644e969a18364713b90b7f27fa1c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16734
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins)
Instead of having each mainboard provide the power button,
uncondtionally provide the power button ACPI device on behalf
of each mainboard.
BUG=chrome-os-partner:56677
Change-Id: I94c9e0353c8d829136f0d52a356286c6bedcddd5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16731
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The mainboard is not being worked on anymore, not available outside of
Intel and thus has litle practical use. Remove mainboard code completely.
Change-Id: Ic2c7ea3810ee70afc01a42786f8ccba9313134e4
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16725
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Some changes were made in upstream in the meantime that broke the build:
- CHROMEOS_VBNV_CMOS was renamed to VBOOT_VBNV_CMOS
- recovery_move_enabled() -> vboot_recovery_mode_enabled()
- chromeos.asl was replaced by an acpi generator
Change-Id: Icd4ed5111cce9db79e12efb0cb7e898bba725c20
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/16683
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Migrate google/enguarde (Lenovo N21 Chromebook) from Chromium tree to
upstream, using google/rambi as a reference.
original source:
branch firmware-enguarde-5216.201.B
commit cf1f57b [Enguarde: Adjust rx delay for norm.]
TEST=built and booted Linux on enguarde with full functionality
blobs required for working image:
VGA BIOS (vgabios.bin)
firmware descriptor (ifd.bin)
Intel ME firmware (me.bin)
MRC (mrc.elf)
external reference code (refcode.elf)
Change-Id: I3ccda29d1e095d8b1b36766cda913172f72233a7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/15444
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Enable the cr50 TPM and interrupt as GPE0_DW1_28 for use during
verstage. The interrupt is left in APIC mode as the GPE is
still latched when the GPIO is pulled low.
BUG=chrome-os-partner:53336
Change-Id: Ib0247653bdcbaccb645cd16b81d7ec3c38f669af
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16673
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These values are found in util/cbfstool/cbfs.h.
Change-Id: Iea4807b272c0309ac3283e5a3f5e135da6c5eb66
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16646
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
