According to request of comment 35, setting ELAN as the default.
BUG=b:122019253
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: Iee5e7a21545ca798c0c22f86906acc8e7d81e945
Reviewed-on: https://review.coreboot.org/c/31430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Eanble Elan touch for sarien EVT build
BUG=b:119763054
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I790436338705fc9d68f714245e9b9bb518ddb30a
Reviewed-on: https://review.coreboot.org/c/31413
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Follow Northbay and intermal project to add GPIO H3(CNVI_EN#) for DVT1.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I580a6e094d84a7bada534b14c2b65ecf4b9942b0
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#) for DVT1.
BUG=b:123342945
TEST=Built and tested on sarien system
Change-Id: I0caf97f6a2a8abf2914667350c76300733ead1b8
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All platforms using this code have NO_CAR_GLOBAL_MIGRATION.
Change-Id: I72effa93e36156ad35b3e45db449d8d0d0cabf06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add available thermal sensors information for CPU throttling action.
BRANCH=None
BUG=b:120058043
TEST=Built and tested on Arcada system
Change-Id: I748ca0ce43915c96d71e63fb03fc3d1a02adc56c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Change-Id: If336e9d7016987be151ab30d5c037ead3a998fe0
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change tcc offset from 15 to 3 for sarien.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: I1c5d144e92d1e6e9c81b3e6686805ccf744b7203
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30808
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Accoding to desciption in FSP header, Vref Configuration will be set to
2 if VREF_CA to CH_A and VREF_DQ_B to CH_B.
BUG=N/A
TEST=Build and boot up on Arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I02e16e141b81d766a6060ca08283f432abd96647
Reviewed-on: https://review.coreboot.org/c/30280
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Most boards currently do not use EC firmware from SPI flash in the
IFD, this hides this option by default and shows it only for boards
that need it.
A new config variable MAINBOARD_USES_IFD_EC_REGION is introduced to
enable this option for boards that need it.
The following list of boards requiring this was provided by
Lijian Zhao:
1. intel/cannonlake_rvp
2. intel/coffeelake_rvp
3. intel/icelake_rvp
4. google/sarien
5. google/hatch
Change-Id: I52ab977319d99a23a5e982cc01479fe801e172a7
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
1) Add a Platform Data Region called SI_PDR which is allocated in the flash
descriptor for this platform
2) Add a DIAG_NVRAM region for use by the diagnostic payload for non-volatile
storage.
3) Encapsulate both RW_LEGACY and DIAG_NVRAM in a region called RW_DIAG
so it is clear they are associated.
4) Move the RW_DIAG region to the start of the RW region so that once we can
re-enable a larger BIOS region this sub-region will be in the uncached area
since it is not accessed on a normal boot.
BUG=b:119435206
TEST=tested on Arcada board to ensure expected regions are present
Change-Id: Ieb8bc4cf70d0a931e4944210112cfaf5c543f9f3
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This reverts commit ad41f55123.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet
the logic output for WWAN_PERST#_R to high.
BUG=120004153
TEST=Boot up Sarien board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Implement HD Audio verb table for RealTek ALC 3204/3254 codec on google
sarien and arcada board.
BUG=b:119058355,119054586
TEST=Confirm audio play back is working on Sarien and Arcada board.
Change-Id: Icedbb510c7668d96c99c657091fc865f03bf7783
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setting sku_id() is not enough to get a value to show up in the SMBIOS
tables, it also needs to be returned as a string for the table creation
to consume. This change defines the smbios_mainboard_sku() function
and returns a string constant of "sku#" as expected.
Change-Id: I03013bab89d53d1eba969c6ffb7e95fcbb315a81
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Trent Begin <tbegin@google.com>
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the option to disable eSPI when ACPI is enabled so the EC
is unable to assert an SMI when booted into the OS. There is a
kernel driver that implements the same mailbox interface so it
cannot also be used by the SMI handler.
Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds a sku_id() function that returns a static value to
differentiate the sarien and arcada boards.
Change-Id: I1fecc675573a6aece7188aae9370733068d45dbf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29486
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This changes uses drivers/intel/wifi chip for CNVi device to ensure that:
1. Correct device name shows in ACPI name space
2. Correct wake up shows in cat /proc/acpi/wakeup
3. Remove cnvi.asl from soc/intel/cannonlake
Change-Id: Ic81de2dce6045ced913766790a40ed19119f5118
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
WWAN start-up control requires RESET# assert after FULL_CARD_POWER_OFF#
set to high more than 10 ms, so force RESET#(GPP_D21) to low at
bootblock stage to match the sequence.
BUG=N/A
TEST=Boot up Sarien/Arcada board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I36eb841a2e8f2b36771d20577314a7451fbee133
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The Sarien mainboard uses the newly added Wilco EC.
- enable CONFIG_EC_GOOGLE_WILCO
- add the device and host command ranges to the devicetree
- have the mainboard SMI handlers call the EC handlers
- add EC and SuperIO devices to the ACPI DSDT
- call the early init hook for serial setup
Change-Id: Idfc4a4af52a613de910ec313d657167918aa2619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a variant of the Sarien board called Arcada. This is currently
very similar to Sarien with differences in PCIe, USB, and GPIO usage.
Change-Id: I432d2ba99558e960d4e775c809cc8bf6aa1a56bf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29410
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sarien is a new board using Intel Whiskey Lake SOC. It also uses
the newly added Wilco EC, enabled in a separate commit.
Sarien is not a true reference board, it is just one variant of
a very similar design. For that reason it is not considered the
baseboard but rather a standalone variant.
Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
