1. Add 2 port 2 endpoint
2. Add support for OVTI5675
3. Guard entries in override device tree by FW_CONFIG
MIPI UFC is on I2C2
This configuration is as per P2 schematics
BUG=b:190674542
TEST=Build and Boot on Brya
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Id3ef974994fd0d447e398b365cdf01d78c94cc4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
When initializing eSPI early, guybrush has requirements to configure the
bus properly. Those are normally run in bootblock_mainboard_early_init,
but when setting up eSPI early, those have not run yet.
BUG=192100564
TEST=Build along with previous patch, eSPI works on guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ifec6113d48aea0bb5efe47909e4faf0161148a99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55864
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To reduce power load, set unused GPIOs to NC and close
unused interface in devicetree. GPIOs and
interfaces are as below:
GPIO: GPP_C18/C19/D12/D14/D15/D19/D20/D21/E00/E02/H06/H07
Interface: I2C1/I2C3/I2C5
USB: port2_3/2_4/2_6
BUG=b:185044041
BRANCH=dedede
TEST=Built bios and test, it reduces power load without affecting
device function.
Change-Id: Ib5999f0e129bf3e660fe293eda7af3e8e1426151
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
UFC on brya can be USB or MIPI
Add FW_CONFIG bit for this option
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I2f1492d7c769aba8da80763124dda474b32cfbfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This changes updates mainboard properties by adding DFP number and
power_gpio for each DFP.
Reference CB:54292
BUG=b:186521258
TEST=Updated BB retimer FW from 3.4 to 3.5 without any device
connected.
Change-Id: I24a02fd446cb66bda9e66e59802b4deea6894273
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This provide a more consistent mechanism to enable corresponding USB
TCSS port.
BUG=b:182960979
TEST=Boot device, Type C port should operate correctly.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Iadc0df2e6e19a5afacbb7db1ae0bc7546dbcdc1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55772
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify driver from hid to generic(ELAN0001 that used
generic driver without hid).
BUG=b:191620724
BRANCH=dedede
TEST=build bios and boot, touchscreen will work properly.
Change-Id: Ife77d514d9906049f237edd169bc07bb53c48579
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
CB:55452 uses FMAP instead of "cbfs master header".
The flash size statement in vboot-rw.fmd does not contain the start
address, resulting in a non-booting system.
Add start address to FLASH statement.
BUG = N/A
TEST = Boot Facebook FBG1701
Change-Id: Id05ad33babb416a37c657b25cdb1e98d47c1a56d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
0xf7f000 - 0x1000 = 0xf7e000, not 0xf6f000.
This fixes build failure when selecting the option to validate the
layout using the flash descriptor (CONFIG_VALIDATE_INTEL_DESCRIPTOR)
Test: build google/casta successfully with IFD validation selected
Change-Id: I6df67f76f5d766a9f4f85ffc3e1f0de4a241f509
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55815
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CBnT provisioning tooling in intel-sec-tools are now cbfs aware
and don't need to have a fixed size at buildtime.
Tested on OCP/Deltalake with CBnT enabled.
Change-Id: I446b5045fe65f51c5fa011895cd56dbd25b6ccc7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55821
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christopher Meis <christopher.meis@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds mem_parts_uesd.txt that contains the only
memory parts used by primus for Proto build and Makefile.inc
generated by gen_part_id.go using mem_parts_used.txt.
BUG=b:186091208,b:189169995
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I423fd9ad4349c51c6e6b166734ae706509d6ac3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
add memory configuration for chronicler,
based on schematic and gpio table, update gpio and devicetree settings for chronicler.
BUG=b:187318819
BRANCH=None
TEST=FW_NAME=chronicler emerge-volteer coreboot chromeos-bootimage
verify bootable with chronicler
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Id5524b97a236dcc64d18ab1cd2ce13f6bb2d998f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55340
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Error Could not add [key.vbpubk]: too big occurs, when Eltan verified boot is enabled.
Update value of VENDORCODE_ELTAN_VBOOT_KEY_LOCATION.
BUG = N/A
TEST = Boot Facebook FBG1701 with Eltan verified boot enabled.
Change-Id: I1faecd189915985df633ac74627fd872ce8867f0
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=b:191213716
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I2d5738442d2c173fd5b4802d8b5dff76b428c6f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55564
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To avoid from using same the name AMDI5682 as Zork, changing to use
AMDI1019. The corresponding kernel change is on CL:2929864
BUG=b:189297564
TEST=Audio works with the corresponding kernel change.
Cq-Depend: chromium:2929864
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Change-Id: Ie89302f3b6cd3edb8253b909fde4722c2ea1e102
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55508
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This motherboard is almost identical to the ASUS P5QL PRO,
with the only noticeable difference being that the ASUS P5Q SE
has a P45 MCH while the P5QL PRO has a P43 MCH. Few changes were
required.
Signed-off-by: Hunter Sell <alicelyralain@gmail.com>
Change-Id: I36612bac16a79f05f3fe57e535e4ba3c73790a86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add Makefile.inc to include three generic LPDDR4 SPDs for the following
parts for Gimble:
DRAM Part Name DRAM ID to assign
MT53E512M32D2NP-046 WT:E 0 (0000)
H9HCNNNCPMMLXR-NEE 1 (0001)
H9HCNNNBKMMLXR-NEE 0 (0000)
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I60f95ac5ed7f3134882f6580335ec33632676796
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Set the GPIO configuration of gimble
BUG=b:191213263
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I667943578a2bf58cc5841564b8df5b6469d7594b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55717
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates mainboard_memory_init_params() function argument from
FSPM_UPD to FSP_M_CONFIG. Ideally mainboard_memory_init_params()
function don't need to override anything other than FSP_M_CONFIG UPDs
hence passing config block alone rather passing entire FSP-M UPD
structure.
Change-Id: I238870478a1427918abf888d71ba9c9fa80d3427
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Temporarily set eSPI mux in verstage_mainboard_early_init.
Ideally cezanne code should have common function to do this and
mb-specific code would just call it, but for now PCI access doesn't work
in the PSP so we can't do it.
AMD team confirmed that the current PSP doesn't configure LPC so we
don't have to disable LPC when configuring eSPI mux so we can
temporarliy skip the LPC part here.
BUG=b:183149183
TEST=boot guybrush with psp_verstage
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I8317409fa5efd1adffc184d75affbb4d305183f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In order to enable ACP DMIC hardware runtime detection, indicate that
ACP DMIC is present.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the _WOV ACPI method
is populated in the ACP device.
Change-Id: I9a53d158ed08a6b46c29bcb8fe3a2a0d108bd6cd
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55030
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add weida touchscreen support for magister.
BUG=b:191633024
BRANCH=dedede
TEST=Build and verify that touchscreen works on magister.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I3de6a84d2d58ef87f0ae13e8a117a980a0210ac4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Randy Lai <randy.lai@weida.corp-partner.google.com>
This selected by default if 3rdparty/fsp is used. There is no need to
override this behavior in the mainboard Kconfig.
Change-Id: I01ee2e90e0eceaa3100d911b5460cf99f413b185
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Config items depends on USE_VENDORCODE_ELTAN but are VBOOT specific.
Correct dependency of these items on VENDORCODE_ELTAN_VBOOT.
BUG = NA
TEST = Boot facebook FBG-1701 with possible combinations of Eltan
security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: Icd1c3e5c70ca562190308752f45aac734826649a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52132
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSP_Verstage will enable eSPI early in the boot sequence. If the
platform isn't using psp_verstage, the system can hang on the first
port 80h postcode that comes out because they aren't routed to an
active device until eSPI is configured.
BUG=b:191370340
TEST=Build without PSP_Verstage, verify system doesn't hang.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I37fbb251cd79609b856c4480ca29ce94b08897d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55738
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the GPIO configuration of primus
BUG=b:190643562
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I405561ae8a44d95ffdc526241f9c52761f67ed35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This motherboard is somewhat similar to the p8h61-m_pro, but also different.
It has two exposed RAM slots with a pinout for four, and it's an OEM
variant used in PCs ASUS sold in stores.
Signed-off-by: Hunter Sell <alicelyralain@gmail.com>
Change-Id: Id08349feb0aeaf21406f814f6d19bbe0d9312a4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
PEG bifurcation is strapped to x8/x8 on this board, but only the first
port is used. Disable the PEG device at 00:01.1 because it is unused.
Should fix booting with commit ae999503f6
(nb/intel/haswell/pcie.c: Add missing pre-ASPM init). The `config_of()`
function call added in that commit makes coreboot die if any PEG device
that is enabled by strapping is not present in the devicetree. While it
is true that the PEG code should not use `config_of()`, this PEG device
should still be disabled on this board as it is never used.
Change-Id: I16809e081f9a56ba2f1fdfcb4b8289d75161056b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Máté Kukri <kukri.mate@gmail.com>
Remove some redundant parts of devicetree comments. This used to happen
when using autoport, but has been fixed at some point.
Tested with BUILD_TIMELESS=1, Lenovo T440p remains identical.
Change-Id: Ie24b5430c7771c9ce4dda6c9a10d70ee9000df7c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
An error in script did not set the attribute properly:
- Entry CS0 is not used as sensor, but as ground,
- Entry CS1 is used as the startup sensor.
This fixes a regression caused by commit
689c25b9d6 (drivers/i2c: sx9310: Replace register map with descriptive names)
EQ=b:173341604
BRANCH=volteer
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I92c01209031e9a917d95b1cb2537b0ce7b93e66d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51893
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add devfn macros for some peripheral devices that are attached to PCIE
GPP Bridge.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I7c5433dff2329f13c282908e2b848405819347ff
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable Acoustic noise mitigation for blipper and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:187760191
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I187702c23712416eaaaaf1e210dcfc6b2c560041
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- Add a codec reset before setting the subvendor ID using the Azalia macro
for consistency with all other Realtek HDA codecs
- disable jack detect for the external mic on the 3.5mm jack, since it's not
currently working, so that the external microphone can be manually selected
Change-Id: Ib0f99e5088973a721c0a295899012c9aea5009cf
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- fix the number of verb entries, which excluded the 4 following the
pin configs
- issue the reset *before* setting the subvendor, and use the Azalia macro
- disable jack detect for the 3.5mm jack, both line out and mic, since
it's not currently working, so that the outputs can be manually selected
Change-Id: Icd961c3c5aec23cf61d6a9ad65c603c6dc04697a
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable FastPkgCRampDisable for all domains, set SlowSlewRate to fast/16
for all domains. This aligns the settings with the Librem 14.
Test: boot Librem Mini v2, observe high frequency acoustic noise reduced.
Change-Id: I10bc2a3e6b631b8c0b430e204f376aa9a81ac683
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Decrease SA slew rate to match other domains and reduce
high-frequency noise slightly.
Change-Id: I02cd93481f6bfba6249cb338a0e2f47d471a438e
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
On dedede boards without Cr50, the CrOS Board Info (CBI) EEPROM write
protect signal is decoupled from the hardware write protect signal.
Instead, we'd like for it to mirror the software write protect status.
This commit simply checks the software write protect status of the SPI
flash and sets the CBI EEPROM write protect if it's enabled. To prevent
changing the WP signal at run-time, the GPIO configuration is also
locked down after the level has been set. If HW WP is deasserted, the
CBI EEPROM WP will be deasserted as well.
BUG=b:191189275,b:184592299
BRANCH=None
TEST=Build and flash lalala, disable SW WP by running `flashrom -p host
--wp-disable` from a root shell and verify that the GPIO is asserted
after a reboot. Export the gpio via sysfs and verify that attempting to
change the value of the GPIO is futile. Enable SW WP via `flashrom -p
host --wp-enable` and reboot the DUT. Again, export the GPIO via sysfs
and verify that attempts to change the GPIO value are futile.
localhost ~ # iotools mem_read32 0xfd6e08d0
0x44000200
localhost ~ # cd /sys/class/gpio/
localhost /sys/class/gpio # echo 217 > export
localhost /sys/class/gpio # cd gpio217/
localhost /sys/class/gpio/gpio217 # echo out > direction
localhost /sys/class/gpio/gpio217 # cat value
0
localhost /sys/class/gpio/gpio217 # echo 1 > value
localhost /sys/class/gpio/gpio217 # cat value
1
localhost /sys/class/gpio/gpio217 # iotools mem_read32 0xfd6e08d0
0x44000200
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ic103037921ec7d2f96f86178675c11a3a1357d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To enable display, we have to:
1. Configure panel power and backlight
2. Configure eDP driver
BUG=b:189985956
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: Ida6c157a6a3bd904d3fa3dd2001385ced34f7711
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55574
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change the default rom size to 32MB and remove chromeos.fmd
because Chrome OS is not supported on EHL for now.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I49d9404eb901087037b5423a4a503c5271e14138
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55554
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to latest corresponding UPD filling implementation, this is not
required.
This patch fixed the brokenness caused by
Commit hash b10afbd2e2.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I49e434f7bbafcb148e82202697e87c3e4268d7b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Turn on CBI and add helper functions for determining the board
configuration from the firmware config settings in CBI.
BUG=b:187316460
TEST=Built
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I212e7f413b4d8a7d15122cde90100a0ec28e88a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54639
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change also restores GPIOs to their proper settings for prior board
revs.
BUG=b:189362981
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I89d7ba94dfbd5e4a000cdde7a0c65f38b53b722d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55325
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_A19(DP_HPD1) and GPP_A20(DP_HPD2) were configured native function
(NF1), this causes redundancy with legacy HPD interruption.
This change configures GPP_A19 and GPP_A20 to be no connection and
disables DdiPort1Hpd and DdiPort2Hpd.
BUG=None
TEST=Boot to kernel and verified no kernel HPD pins assertion message.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I80ef40a1aca19cd6ad56219175d2fd40890a393d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sanrio Alvares <sanrio.alvares@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Touchpad: 387.7kHz
Touchscreen: 389.4kHz
Audio: 387.6kHz
P-sensor: 372.5kHz
BaUG=b:178092096
BRANCH=dedede
TEST=Build and EE check after tuning I2C clock is under 400kHz
Change-Id: I4f6bdd3802cd94671325a89458cde981a2ffa929
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The GPIO_GSC_AP_INT itself is active low, but the payloads will
create the IRQ using its eint driver, which is active high.
BUG=b:188392736
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ie39f3b9a5dbe15057ef3e96f6c99211949692003
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Any chip entry without a device node below them are silently dropped by
sconfig. Copy the same device node from the devicetree to prevent this.
Change-Id: I778f6b2d980e78142ae12ef941e7d9bd1f753057
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55540
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the default state of the MMIO UART devices in the chipset
devicetree is off, the mainboard devicetree entries that disable MMIO
UART devices are removed.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I913a587802020ce4e182b48632cdde1104c2a6e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55545
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the cappy variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190515828
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Id5a3b0cb475ee77a9f62523d8322a5e4123ce3be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add camera support in devicetree.
BUG=b:190797339
BRANCH=None.
TEST=built pirika firmware and verified camera function is OK.
Change-Id: I66ded32105f3166e2faec3ea5dcfb93c29822366
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55450
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to meet timing requirement of WWAN reseting it in early GPIOs
and asserting Reset GPIO in ramstage
BUG=b:180166408
TEST=Build and boot Brya system and verify enumeration of L850 and FM350 devices
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Id6d69696b6c645eec3fa314a608c69214bafba82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54912
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC Serial Bus pins were removed with ICH5 already, so a choice
'irq_on_fsb = 0' would not take effect. The related register BOOT_CONFIG
0x3 is also not documented since ICH5.
For emulation/qemu-q35 with ICH9 the choice INTERRUPT_ON_APIC_BUS was
wrong and ignored as BOOT_CONFIG register emulation was never implemented.
For ICH4 and earlier, the choice to use FSB can be made based on the
installed CPU model but this is now just hardwired to match P4 CPUs of
aopen/dxplplusu.
For sb/intel/i82371eb register BOOT_CONFIG 0x3 is also not defined
and the only possible operation mode there is APIC Serial Bus, which
requires no configuration.
Change-Id: Id433e0e67cb83b44a3041250481f307b2ed1ad18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55257
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This a mainly a preparation for adding the MMIO UART devices to the
chipset devicetree.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I533e4a909fdeb1614dbc5df015440b9df5d83233
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The BMC EEPROM layout has been updated to contain system and mainboard
serial numbers. Use these values in SMBIOS Type 1 and Type 2 tables.
Change-Id: I55b51a856b4ad28fd56b02015b2e1d49cd629735
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55275
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use hostbridge.asl from Haswell instead of Broadwell. Both files are
equivalent. Then, drop the now-unused hostbridge.asl from Broadwell.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I87d51727b75a9c59e2f5f3ba8d48c575ce93c78c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Mainboard information can be found in the included documentation.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ic811e24bd72da84e5ca8f5b09f2eb65872153b72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55111
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable all display related UPDs if IGD is not enabled as FSP
don't need to perform display port initialization while IGD itself
is disabled else assign UPDs based on devicetree config.
TEST=Dump FSP-M display related UPDs with IGD enable and disable
to ensure patch integrity.
Change-Id: I0479904141dfc5e707679109aa18b7ef4264cf96
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add support for the ThinkPad W541 based on Peter Lemenkov's initial W541
port. Compiled and tested with SeaBIOS and Tianocore booting into Arch
Linux 5.10.32-lts. The Haswell mrc.bin blob is required.
Tested working:
- SATA SSD
- SATA DVD drive
- M.2 SATA
- All USB ports
- SD card reader
- Speakers/headphone jack
- Keyboard/touchpad
- libgfxinit
- VGA
- mini DisplayPort (Thunderbolt untested)
- eDP laptop screen
- NVIDIA GPU in Linux
- Camera/Mic
- Smartcard reader
- Internal flashing when IFD is unlocked
- ThinkPad basic dock (VGA, USB, Ethernet)
- CMOS options
- WLAN
- Bluetooth
- Ethernet
- Using me_cleaner
- All DDR3 slots
Not working:
- Keyboard backlight
- First boot can take up to 20s (MRC.bin is slow)
Untested:
- Thunderbolt
- Internal flashing when IFD is locked
- Other ThinkPad docks (DisplayPort, DVI, Audio)
- ExpressCard slot
- Battery thresholds
- WWAN card
- Fingerprint reader
- USB Debug console
Signed-off-by: Justin Wu <amersel@runbox.me>
Change-Id: Ia43070f51bba3cf59ba9b7d9e29e4e778efbeb08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52659
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The system will hang when resuming from S3 if the SSD reset gpio is not
reset early enough.
Change GPP_A11 in baseboard to PLTRST to avoid an S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ia78d813cb6bc689b07e8d8ead1ade6e77f925ce1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The same functionality can be provided through a runtime-generated SSDT.
The remaining parts of device NVS are removed in a follow-up.
Since the SSDTs are only loaded after the DSDT (if loaded at all), using
SSDT-provided objects outside method bodies is not possible: the objects
are not yet in OSPM's ACPI namespace, which causes in ACPI errors. Owing
to this, the operation regions used by the _PS0 and _PS3 methods need to
be moved into the SSDT, as they depend on the SSDT-provided BAR1 values.
Tested on out-of-tree Compal LA-A992P, generated SSDT disassembles with
no errors and contains expected values. Linux does not complain either.
Change-Id: I89fb658fbb10a8769ebea2e6535c45cd7c212d06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Many more asus boards using Panther Point PCH other than Z77 can be
added as variants of this series.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I3e0b5734658912a69ccde94d530399059502c4c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Mainboard information can be found in the included documentation.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ic56ac0e5f93a6e818ef0666e41996718471b1cf6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set register "generic.stop_delay_ms" to 150 to reduce power resume time.
BUG=b:185308246
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Idd90191ee7ecbbc544121dc0b93101bea64f0e5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54275
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD support to elemi for MT40A512M16TB-062E:R
BUG=b:190020997
TEST=FW_NAME=elemi emerge-volteer coreboot chromeos-bootimage
Change-Id: I548ea2ec01dd0a43442a691cf870c2bc1b58bc74
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This is the same settings as voxel.
BUG=None
TEST=FW_NAME=trondo emerge-volteer coreboot chromeos-bootimage
Verify that the image-trondo.bin is generated successfully.
Change-Id: I04df68ce1683fa32195df1a93f5bde2e3efe6090
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Create the gimble variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190334274
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GIMBLE
Change-Id: If425571d95b3b20910f890428fb5726ebad2fdf4
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55300
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the scout variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:187080143
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SCOUT
Signed-off-by: Jeff Chase <jnchase@google.com>
Change-Id: I3be9d2d30821c2c9132ed94c9faf1f33b62bbc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Regenerate SPD for MT53E1G32D2NP-046 WT:B with correct value of ranks.
BUG=b:190692797
TEST=Build and boot to OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Icee095c7114f1d6dd960f2134db3816b367bf987
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The SKU ID for Cherry is retrieved via CBI interface.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Icefa016c2e5f68bd194f76d2252856835c65b8e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
volet don't support usb4, remove it to prevent USBC(P0) issue.
BUG=b:189740531
TEST=build and verify USB(P0) disaply out normal
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia78c7cee76ec2e3a5334ad8805a0d45616aade93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55344
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add EC_HOST_EVENT_HANG_DETECT to S3/S5/S0ix wake mask. This event is
sent when the EC detects the AP didn't fully enter a sleep state.
BUG=b:186571086
TEST=Trigger hang detect while AP is in S0ix, AP wakes from S0ix
Change-Id: I09ccf609fc453c19b4fb1ddaa5a0c86d7a85aad1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The patch updates PMC Descriptor which is part of Descriptor Region if
system equipped with Alder lake A0 silicon. This change allows to use
unified Descriptor Region for Alder lake A0(CPU ID:0x906a0) and B0
(CPUD ID:0x906a1) silicons.
BUG=B:187431859
TEST=Verified PMC Descriptor getting modified for Alder lake B0 silicon if
not updated.
coreboot logs appear as below with this patch:
On First boot after flashing the image:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
CPU: Genuine Intel(R) 0000
CPU: ID 906a0, Alderlake Platform, ucode: 0000001a
..
FMAP: Found "FLASH" version 1.1 at 0x1804000.
FMAP: base = 0x0 size = 0x2000000 #areas = 32
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Erasing flash addr 0 + 4 KiB
Update of PMC Descriptor successful, trigger GLOBAL RESET
Next boot after GLOBAL RESET:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
..
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Update of PMC Descriptor is not required!
VBOOT: Loading verstage.
..
CBFS: Found 'fallback/verstage' @0x2264c0 size 0x16b08 in mcache @0xfef84d38
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6d9a2ce0f0b3e386eefa1962ce706b58f31a8576
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Note that there are assumptions about LAPIC MMIO location
in both AMD and Intel sources in coreboot proper.
Change-Id: I2c668f5f9b93d170351c00d77d003c230900e0b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55194
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently variant_has_fpmcu() is called very early in bootblock, before
eSPI is initialized. When checking CBI for its presence, that causes
an error and nothing else can be read from CBI in bootblock.
Moving it slightly later in bootblock doesn't hurt anything from a
timing standpoint, and allows CBI to be read.
BUG=None
TEST=See CBI get read and the FPMCU field read correctly.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6de44119e92c8820b266f9f07287706c7d4eb505
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Most of the Kconfig files for Intel SOC devices define the MAX_CPUS
value within src/soc/intel/*/Kconfig.
Move the definition there for Tiger Lake and remove from the mainboard
Kconfig files.
Signed-off-by: Andy Pont <andy.pont@sdcsystems.com>
Change-Id: If145b9eb5d99821f4ce513118e4417d05f821ef5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add Realtek audio codec ALC5682I and speaker L/R the same way as in waddledee
BUG=b:188446060
BRANCH=dedede
TEST=Boot to check ALC5682I and speaker L/R are functional
Change-Id: I8173ffbfb1a8f18978a5e35c69972d4a6d8cb04a
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54529
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Provide functions to allow for variants to override only a few pads from
the baseboard table.
BUG=b:189362981
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I3ae6c11ca8614d523f3402f1c1abb7c82124e473
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add low_power_probe config to camera devices so that driver skips initial
probe during kernel boot and hence prevents privacy LED blink.
BUG=b:178060668
TEST=Build and boot to OS on Drawcia. Ensure no blink on privacy LED.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I00dfe2ce0b57ff3eaa258204f49e79a280754dcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52190
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add function to force memory training and add VPD variable to operate
this function.
Tested=On OCP Delta Lake, memory training can be forced via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I53a923b51b36f9f5db491ef142109f58f9a4611d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds a new variant called Pazquel that is identical to Lazor
for now.
BUG=b:187232137
TEST=make
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ib531ea5df19fe91e619f23baada73842554538ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This will tell the kernel to ignore PCI ASPM when suspending the device
and instead place the device into D3. We don't actually have a pin to
control power to the NVMe so we leave it in D3Hot. I'm not sure if
`PCI_RST#` is working correctly on S0i3 suspend/resume. If it's not
acting as expected we can add the reset GPIO and have the OS do it.
BUG=b:184617186
TEST=Run suspend_stress_test on guybrush for 10 cycles
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I29539ac120a9f1b7c1bfeaca745cfc82acfa461a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54967
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Power limits (PL1 and PL2) depend on the specific SKU of the CPU.
By expanding the SoC chip config power_limits_config member to
an array indexed by ADL_*_POWER_LIMITS_*_CORE macros, the
appropriate power limits are applied. Using this the correct
set of power limits are being selected from the array based on
system agent PCI ID. Based on this, chipset.cb file contains
the set of power limits being used by varieties of ADL boards.
These power limit values are as per document 619501.
BUG=None
BRANCH=None
TEST=Built and verified the following console output on below boards
On adlrvp (482):
CPU PL1 = 28 Watts
CPU PL2 = 64 Watts
On adlrvp (682):
CPU PL1 = 45 Watts
CPU PL2 = 115 Watts
On brya (282):
CPU PL1 = 15 Watts
CPU PL2 = 55 Watts
Change-Id: Ic1676e2b4d611cdc85e770f131d5b6d5ecd180be
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
This changes adds the EC_HOST_EVENT_USB_MUX to be dark resume source.
BUG=None
TEST=Build coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I6f4dcbc60a6cb131f28de205bd9ef436f2b508eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55126
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IO MWAIT redirection is not enabled, and C-states are reported using the
_CST ACPI object, which overrides the P_LVLx values.
Change-Id: I737bd58bcda3e7c5f6591e4c2309530ff035e2c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
IO MWAIT redirection is not enabled. The code is missing, but C-states
should instead be reported using the _CST ACPI object.
Change-Id: I21fd2fa6ee4aa1ed57694549d5cb48159f37af26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Using an array reduces the amount of boilerplate code.
Change-Id: Ic6a48a01d3b96e69273dc28bdb6699ce7c0931b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55246
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GSC is connected with AP via i2c bus so we need to enable i2c in
psp_verstage.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5f7b73be67a692ea7de31ae53bd111d0e4b6998c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These PCH PCIe ports are used and should be enabled.
Resolves: https://ticket.coreboot.org/issues/311
Change-Id: I26ace6e043c7c66f8944f0986923014703423b8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Looks like the comments were derived from a preproduction board's
schematics. Production boards use a different port mapping.
Change-Id: I40c267ff048959b131c22c07695212e8bd90c3f4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
shadowmountain board variants.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: I2b769d653ad8ad8ff069a0787d00ff33ead5c912
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
different adlrvp boards.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: Ib9e82d953416c076588974f3167d00ae96f01bb5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Chromebooks the RAM code is implemented by the resistor straps
that we can read and decode from ADC. For Cherry the RAM code can be
read from ADC channel 2 and 3.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4f28bc1c567cb886bd90d930219981a6206b9bb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
This patch adds support for SPM. This adds 43ms to the boot time.
TEST=program counter of SPM is correct value after booting up.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5f17f6d51fc9ad2d23c71c3c5cd29fdc777dc071
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55154
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 2e665eb8da.
Reason for revert: Was submitted too early and out-of-order.
Change-Id: I119b7a81b849bbe3424d73d5fdf9b55481444686
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54971
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I2C4 is not used pn Brya hence make below changes:
1. Disable it in SerialIoI2cMode.
2. Remove I2C4 config in common_soc_config.
TEST=Make sure FSP is not programming I2C4.
Change-Id: I94c72b7fac9d8a001913b5faa2c0c8a3e8b701e9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for LabTop Mk III (kblr) and LabTop Mk IV (cml)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iffa6061b0e600880b0c93746f35b1731e4841e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In order to support no MIPI camera variant, move related configuration into variant folder.
BUG=b:188272162
BRANCH=none
TEST=build no MIPI camera variant without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4e64d078a8e39732ad29443c3b09ca008a7e902f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on schematic and gpio table of volet, update gpio and
devicetree settings for volet Proto.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia0e9557e01ce1e7a49a3dddf6da3e4a29587a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55113
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add 1 port and 1 endpoint
2. Add support for OVTI8856
WFC is on I2C0
BUG=None
BRANCH=None
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Ic5e9c28f255bdf86a68ce80a4f853be4e7c7ccfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=Boot to OS and verify acpi tables.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3c78ac44afa3515acef9ea2d59f22f95e6b45e90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54490
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Reviewed-by: John Zhao <john.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variant mc_apl1 is the only one that uses gpio.c from baseboard. For
this reason, gpio.c is moved from baseboard to mc_apl1.
Change-Id: Ie2ba8181dfe887df9abbbd648f2cbdc6ffc65530
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
With commit 405f229689 (soc/intel/*: drop UART pad configuration from
common code) the UART pad configuration was dropped from common SoC
code. Through a second commit 5ff17ed393 (mb/siemens/mc_apl1: do UART
pad configuration at board-level) the UART pad configuration was made
for mc_apl1 baseboard. This change is also needed for all other mc_apl
boards.
Change-Id: If78726d9b141e4e7580cca3267f49c1a5b95d7fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Upload the FSP-M UPD configs. This CL also updated the chip.h and
devicetree.cb with the relevant variables and configs.
This CL also updated the GPIO related settings (PMC & SD card) in
devicetree.cb.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If6321064b37535b390cf3dd7c41a719c598a0cd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
`mainboard_silicon_init_params()` should *only* be used for configuring
FSP options which can not be configured anywhere else. Therefore, use
the init phase from the mainboard_ops driver for configuring the GPIOs.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Ia01091938ac113cb5cf95f046609a1ebf3620806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48143
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the first version DPTF parameters received from the thermal team.
BUG=b:188936764
TEST=emerge-volteer coreboot chromeos-bootimage
Cq-Depend: chrome-internal:3851737
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Id14b1d0bdd48c65eafbdd2e80b4611c86781be00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These PCIe and DMA ports are not available for adlrvp_m.
BUG=none
TEST=Boot device
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Ic568c692fbb82fb3fc70c0cafc2328f8fa2cd74d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enabling AC connect/disconnect wake events in brya to meet Chrome OS
wake requirements.
These changes are similar to Volteer and Shadowmountain.
BUG=none
BRANCH=None
TEST=manual tested DUT wakes for AC connect/disconnect in S0ix
Change-Id: I14b3efd429e3aa701af534f150baf35fcdeb9f35
Signed-off-by: madhusudanarao amara <madhusudanarao.amara@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54855
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Sooraj Govindan <sooraj.govindan@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initial upload of the GPIO configs for EHL CRB.
This CL also includes the UART GPIO configs in early GPIO table.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ied4cbb34149b0b837597c0fc17dc5956f3ca409e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
We would like to have an easy way to completely disable TPM support on a
board. For boards that don't pre-select a TPM protocol via the
MAINBOARD_HAS_TPMx options, this is already possible with the
USER_NO_TPM option. In order to make this available for all boards, this
patch just removes the whole USER_TPMx option group and directly makes
the TPM1 and TPM2 options visible to menuconfig. The MAINBOARD_HAS_TPMx
options can still be used to select defaults and to prevent selection of
a protocol that the TPM is known to not support, but the NO_TPM option
always remains available.
Also fix some mainboards that selected TPM2 directly, which they're not
supposed to do (that's what MAINBOARD_HAS_TPM2 is for), and add a
missing dependency to TPM_CR50 so it is set correctly for a NO_TPM
scenario.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0a73da3c42fa4e8deffecb53f29ee38cbb51a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id1c6a6cbbdda2cb22e81e2b52b364617d6765e09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54963
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5cbc620001d3c21c538b62ab2811b6e07269feb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54962
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The firmware config field in CBI lets us control initialization
parameters based on the OEM design.
BUG=b:188713024
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I56ddc7218688919f20f41e0f143419c39d83849d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the default for the corresponding UPD of the Picasso FSP is
DXIO_PSPP_POWERSAVE and the devicetree default is DXIO_PSPP_PERFORMANCE,
add a deviectree setting for each board that's using the Picasso SoC
code to not change the setting for the existing boards.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0008ebb0c0f339ed3bdf24ab95a20aa83d5be2c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Not sure which policy we should select here or if that should be done in
the board-specific devicetree overrides instead of the baseboard.
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I792d909ce75cb73571c9fec58c18f749ea3ae029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54933
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All relevant USB phy settings can now be controlled via devicetree.
The given values are the AMD default ones.
For proper tuning procedure and values contact AMD.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ie8d08bde54f8c0cb8202ba111b9c7a9bd33fa03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Configure GPIO CAM_PDN5 (AP_XHCI_INIT_DONE) as output, so that
payloads (for example depthcharge) can assert it to notify EC to enable
USB VBUS.
BUG=b:187149602
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I3bf63f91b8057e35be2780024a8b398c3044729b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54902
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Build of the entire smm-class is skipped if we have
HAVE_SMI_HANDLER=n.
Change-Id: I64bdcb28a996609111861ebafe172493b0650354
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54852
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Rocky Phagura
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
haboki/habokay is the same design as drawlat/drawcia, and differs only
in replacing Cr50 with discrete TPM.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot
Cq-Depend: chrome-internal:3850094
Change-Id: Id866927b7041c5bf1c73fb4f0c03798eb61efa79
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54755
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new memory MT53E512M32D1NP-046 WT:B in the mem_parts_used.txt and
generate the SPD ID for the parts.
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib797af858e8f7ea275291e552102db74f4724aad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 2f8a7046bb.
Reason for revert: CB:54752 makes this unnecessary
Change-Id: I3ad0bcafe50e3eafb9a106720c6c9ea5cb0efc4f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54789
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
