Some efuse settings would not be applied automatically, so we need
set the settings manually. The low power consumption would not be
optimal without correct efuse settings.
BUG=b:172636735
BRANCH=none
TEST=see 'pmic_efuse_setting: Set efuses in 11 msecs'
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Ideb862c3cb0f1fee183804aed74fcf141bf1f5df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
For pq module size registers such as DISP_AAL_SIZE, the high bits
should be HSIZE, while low bits should be VSIZE. Fix the incorrect
settings for these registers where width and height are reversed.
According to MediaTek, there is no practical impact on mt8183 devices,
but it's still nice to get this fixed to avoid future confusion.
BUG=b:171167210
TEST=none
BRANCH=kukui
Change-Id: I4b6aedf9a3ca133fcbe9cb88b99a13d228233e24
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46626
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is located below TOLUD. The size is configured in ESMRAMC but can
also be configured with "-global mch.extended-tseg-mbytes=5" command
line argument. Note that the size in ESMRAMC needs to be 'invalid' (3)
for this to take action.
coreboot will leave TSEG at the default 1MiB.
Note that even if TSEG does not end up being used, it is likely a good
idea to not put anything there as if SMM gets locked down by something
else it will suddenly be inaccessible.
Change-Id: I5fd82a42d6602f1369bb3c69556c46f537542705
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Broadwell code unconditionally enables timed MWAIT, but not all Haswell
steppings support it. In preparation for merging Haswell and Broadwell,
also enable timed MWAIT on Haswell code, but only if it is supported.
Change-Id: I1d11d62f1801d65ae4d5623994fd55fd35e8f34a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46916
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The old code was broken and register 0x90 didn't even exist any more in
the config space of the SMBus PCI device, so just always return the MMIO
base address of the SMBus controller. As far as I've seen, no board in
tree uses this functionality at the moment.
Change-Id: Ib80d5c928da6022427afb8ccc969fb2aac953c2d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a bootblock gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: Iad40b6315a29e7aea612a3e1a169372d296d1d6c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49443
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I357099f797be178543a9e6637335cd0a68633071
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49441
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I8b30eb5d70c34ae3e2ed24ab52dd1357a54c5ae7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49439
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I0b956427a9cec56d06b03f7f05138f75137b4ea3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49437
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ibc727302109456eb1d86652c947ce85b3a64c5b2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I80369ab70d5510cb4f388f3029119e7148361af4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49435
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Id6b55d7f3d3fbfc5b55497708f24006614760d03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49434
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I130fd26944169430a84c3609432b1b5283581c99
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49432
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ie3878b47b8e20c51b928a38df9ccedf2d50d478e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49431
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib19a4f64eaf25bf2eb47ee60748a68538fc0729a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49430
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I279956f30cbb6fb031cdfe6aaa09b644b6b7d3e7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49427
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LPC/eSPI pad configuration is already done at board-level. Thus,
drop redundant configuration by dropping the call to lpc_configure_pads.
Change-Id: Ib9e62bf19e6f1fbe32a340e4802c13504a0d6def
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49417
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie1e53e72c65fdcfe4be2e01134873aa7858c28ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49416
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding one missing pad to the early gpio table and
dropping the call to the soc function.
The soc code gets dropped in CB:49410.
Change-Id: I210633d4520fcfab59f68268bd7991557433ce38
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49415
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: If0693a4419c58dde3c4536698940f03c30304b9d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49414
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding missing pads to the bootblock gpio table.
The soc code gets dropped in CB:49410.
Change-Id: I95993b1bd4f1fd8b4ac7b21fb89ec4d196b0240a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49412
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I62ffbe36bd7b7675aa0f41a8c6e9214d04ad4ae5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49428
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I6fedcebea3bb31d992bac1e3b21382fea93a8b82
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49429
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ieeb738afd54e77ee853ee109009f611411aa0d4a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49426
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5482f44b361925b7d2dbcbf1065c1be035c68b0b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49424
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I7dcf88d61c305f0598a0a79f8cfa46ef5009564b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie33bae481f430a1c4410a0a4e2b2a34a3e78adaa
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49411
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `mobile` suffix is misleading, since desktop CPUs share the same
CPUIDs. Remove unused stepping IDs and add the full CPUIDs instead.
Finally, add Broadwell CPUIDs in preparation for merging CPU code.
Note that steppings for Haswell in various comments are incorrect.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I19e56b8826b1514550ae95e6363b0df2d08e3cb7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46915
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Backport Broadwell's s0ix support to Haswell in preparation to unify
both platforms' CPU code. Note that only ULT variants support s0ix.
This option is currently unused, but will be put to use in subsequent
commits, when switching Broadwell mainboards to use Haswell's CPU code.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I91c6f937c09c9254a6f698f3a6fb6366364e3b2b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46924
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `clear` command for SMMSTORE version 1 does not require a parameter.
Change-Id: I992b7ce5962bf7ee62b7e1970ae7aa1b975ef42e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49724
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow MRC training in SA GV.
BUG=b:177779469
BRANCH=firmware-volteer-13672.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Idc9f634135b489450f53f8cd28d80649309d0f70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Assigned USB2 port to type-c use.
BUG=b:177483060
BRANCH=firmware-volteer-13672.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I9bd820406124927d56296508be05033217c0d472
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49638
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On FSP1.1 platform cbmem_initiailze() is called in
chipset_teardown_car_main(). This causes double
call op cbmem_initialize().
Add call to cbmem_online() to avoid double CBMEM init.
BUG = N/A
TEST = Build and boot on Facebook FBG1701
Change-Id: I449ddfc94f1099d7c0e9005e6a5cf509e1433bb1
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
prog_locate() will load FSP, before CBMEM is initialized.
The vboot workbuffer is used for loading, but
CBMEM_ID_VBOOT_WORKBUF is not available.
A NULL pointer is returned as workbuffer resulting in error
'Ramstage was not loaded!' at second boot.
Initialize CBMEM before calling prog_locate().
BUG = N/A
TEST = Build and boot on Facebook FBG1701
Change-Id: I2f04a326a95840937b71f6ad65a7c011268ec6d6
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For the time being every soc/intel selects ACPI_SOC_NVS
and pwrs is a required field for the common initialisation
implementation of followup work.
Change-Id: I4a0c7eb35f0646898e49fad15c6448607c398731
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49493
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
0 is converted to not used, so use a special value to allow using PCIe
root port #1.
Change-Id: I2d64afc9bb4627913492edad8f36566e7fb18166
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change updates pcie_rp.h to reflow the comment blocks to fit
within 80 columns to match the original style of the file. This
addresses comment received on
CB:49370 (https://review.coreboot.org/c/coreboot/+/49370/comment/0f3fe10d_4e218b5f/).
Change-Id: I565ad602e0e3a2ee09e8345479d82e2ce0a31fd0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Increase DCACHE_RAM_SIZE to 32kB and remove "NO_CBFS_MCACHE".
It’s quite safe to increase DCACHE_RAM_SIZE. All LGA775 targets
should have at least 256K L2 cache. That is plenty for XIP RO cache of
bootblock + romstage and a 32K CAR.
Change-Id: I393b2727bd90a990c3108a4dbead62b17d7fc531
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Correct GPIO settings as below reason:
1. GPP_G7 not being used but set to NF.
2. GPP_C22 and GPP_C23 is set to NC but internal pull down to 20K
BUG=b:177283756
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage and boot into emmc
Change-Id: Idf25674efa2336bde98c5abaff278484fd71ea8b
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to NC
BUG=b:175932166
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage and boot into emmc
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id7780d5332551ed3fd20ef14f8b5d31164f16385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This SOC_INTEL_DISABLE_IGD Kconfig will allow to skip IGD
initialization using FSP GOP and eventually disable the IGD.
TEST=Able to get depthcharge pre-OS splash screen when mainboard
user selects SOC_INTEL_DISABLE_IGD with below HW/FW/SW
configuration:
HW: ADLRVP + AMD Radeon RX 5700 PCI-E DGPU
FW: coreboot with depthcharge as payload for ADLRVP and OpRom for
AMD PCI-E DGPU
SW: Chrome OS RC10 release
Change-Id: I465541cb45c9022d53a5beb3fff1f80660c357c9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This adds interrupt handlers that end up calling x86_exception().
Change-Id: I3dce539b6f1ef300cf16f20224744a75100f60b8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug, so there is no need to specify a MMIO address for the early EHCI
BAR configuration.
Change-Id: I5e904c160c68805a8606a8b2d1ab4fb6172066e7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug.
Change-Id: I2dae22c0db294f5334d9796d90f432d6c8d304df
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The code for setting the LPC generic memory range uses an array of fixed
address ranges not needing explicit decoding, to decide if the address
needs to be written to the LGMR register. Most platforms only mistakenly
add the PCH reserved mmio range, that is not decoded generally,
effectively breaking the mechanism. Only APL uses the array correctly.
That code, in it's current state, does not work (except for APL) and
currently, there is not a single user. Thus, drop it before people start
using it.
Change-Id: I723415fedd1b1d95c502badf7b0510a1338b11ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I795b8da3c5e1efb51c8fe4673f025839a1c630bc
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I2f484d232a46214ff98168f41f96d56b047892e2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I67bdd9a96928b77a9a178afea7dab03dc370312c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I342b9217af0288a3b525e629aac791eb0f880442
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
We need to write some special values to key protection registers before
applying init_setting table and lp_setting table to PMIC. Otherwise,
those settings won't take effect.
After applying init_setting table and lp_setting table, we lock the
settings by writing zero to key protection registers.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I593d4e02bf0b62ac297957caf4ae1c1837f1f38d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Functionality depends of CMAP and CMBP references inside board
specific ASL implementation. Only roda/rk9 and roda/rk886ex has
that.
Change-Id: I4da8292375cb589d67dc68496b1e81971bc2a61f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49274
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Only amd/picasso and amd/stoneyridge have reference to
PCNT and that could be replaced with acpigen.
Remove the PCNT name from GNVS OperationRegion elsewhere.
Change-Id: I7dd45a840b3585fd24c31fd923b991c34ab4d783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000.
Change-Id: Ia6c2ee29e37040ea9b11505e9888c7f6f8da78bc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This memory is used for option roms and BIOS. This matches the ACPI
code.
Change-Id: I53dd4b967569889108352ca70086a12ce252e8e0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: I626989fa6625e0b3613a11e709c614d40a788b0e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: If4e05f496abc05e06a944b244824376f3937a57b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Chrome EC dropped strago support, so we need to disable it here
before updating our Chrome EC submodule.
Change-Id: Ied8905e995fd040b981ce18e95e225ade496d23c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48216
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Struct will be synced with picasso with followups.
Change-Id: I5f460cc3849bf1fad1f6da61169893488ccb2b40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48855
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use the function smbios_mainboard_version()
to query the board revision from the EC.
we need to select GOOGLE_SMBIOS_MAINBOARD_VERSION.
BUG=b:177818769
TEST=1. emerge-volteer coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Change-Id: I2474ee03845356d0775f6da25274f696ad33f935
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SoC code has in implicit dependency on this option, so select it in
the SoC code instead of the mainboard code.
Change-Id: Iea908c142f4a94a107cf74a31d9f5e29668d4b5b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the sasukette variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:175848514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKETTE
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I0a554efe0919dc2f5880f0f7817a37bd4be88ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change enables LTE modem for sasuke.
- Add LTE modem device into devicetree
- Add GPIO control for LTE modem power on and off
BUG=177177967
TEST=Built and verified modem device existence with lsusb
Change-Id: I34ba8ab00b73f24d1786ab014e9981b172a63a27
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49163
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Writing 0 to MSR IA32_BIOS_SIGN_ID before fetching this MSRs content
is required. This is how things are done in
cpu/intel/microcode/microcode.c.
The "Intel® 64 and IA-32 Architectures Software Developer’s Manual"
also recommends this: "It is recommended that this field be preloaded
with 0 prior to executing CPUID" (this field being %edx).
Change-Id: I24a87aff9a699ed8ab2598007c8b8562d0555ac5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DPTF paramerters from thermal team.
1. PL1 max =5.8W
2. PL1 min =3.8W
3. PL2 =20W
BUG=b:177249297
BRANCH=dedede
TEST=build image and verified by thermal team.
Change-Id: I19654b65613817ebecf979ce7ac4f76d370ebdc2
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update SMBIOS type 17 type detail. Define this field by module type.
Tested=Execute "dmidecode -t 17" to check type detail is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I6700056edad5db2b86f6da526329b1343b026385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested=On OCP Delta Lake, verify the VPD values can be read
correctly.
Change-Id: I1c27cb61cd52902c92b3733e53bc8e6fd6a5fe7f
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Given the lack of documentation for this platform, having this info
in coreboot logs (e.g. from board_status) can be pretty useful.
Change-Id: I6a743c1efc1b6da71589460a69bfe4785e3e77a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We found that the switch frequency of vgpu is at 4~5Mhz with high
current case (> 3.5A) and is at 2.5Mhz with low current case(< 2.8A).
The switch frequency of vgpu should be kept at 2.5Mhz.
The root cause is that phase config of vcore is not disabled, it will
affect the switch frequency of vgpu. Corret the phase setting at
initialization.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I48d3729302de9e3343dce79fe6f5ed045d0296a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49005
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After calibration, we can get ddr vendor id or density info from
MR5 or MR8, this helps to make sure the DDR HW is as we expected.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ie62948368716d309aab8149372b2b6093fc33552
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
It looks like we didn't care to reserve the VGA MMIO (a & b segments)
and the c..f segments, initially. It was probably never needed until
the new resource allocator that will make use of any unclaimed space.
Change-Id: Iebdae64914d9f8301cafc67a5aba933c11294707
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It is claimed getac/p470 has this implemented and not
as a TODO.
Change-Id: Ifa9ec5bcb8b25b6334b589e4bc7bcb915e85e349
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49349
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The layout of GNVS has expectation for a fixed size
array for chromeos_acpi_t. This allows us to reduce
the exposure of <chromeos/gnvs.h>.
If chromeos_acpi_t was the last entry in struct global_nvs
padding at the end is also removed.
If device_nvs_t exists, place a properly sized reserve for
chromeos_acpi_t in the middle.
Allocation from cbmem is adjusted such that it matches exactly
the OperationRegion size defined inside the ASL.
Change-Id: If234075e11335ce958ce136dd3fe162f7e5afdf7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 27af8a7e5d.
Reason for revert: This depends on CB:45517 which hasn't landed yet.
Change-Id: I2a6fbf54cfe01bf25e9ea8da84f6f2a17418f0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49647
Tested-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This will remove "CONFIG_FRU_DEVICE_ID=0" from ".config" when unused.
Change-Id: Ic50de165c1f3de3886d3cd1ae66853c9fad35ed2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
According ADL EDS to update the PCH and CPU PCIe RP table.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idcc21d8028f51a221d639440db4cf5a4e095c632
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Hsin-Hsiung Wang