This SOC_INTEL_DISABLE_IGD Kconfig will allow to skip IGD
initialization using FSP GOP and eventually disable the IGD.
TEST=Able to get depthcharge pre-OS splash screen when mainboard
user selects SOC_INTEL_DISABLE_IGD with below HW/FW/SW
configuration:
HW: ADLRVP + AMD Radeon RX 5700 PCI-E DGPU
FW: coreboot with depthcharge as payload for ADLRVP and OpRom for
AMD PCI-E DGPU
SW: Chrome OS RC10 release
Change-Id: I465541cb45c9022d53a5beb3fff1f80660c357c9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This adds interrupt handlers that end up calling x86_exception().
Change-Id: I3dce539b6f1ef300cf16f20224744a75100f60b8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug, so there is no need to specify a MMIO address for the early EHCI
BAR configuration.
Change-Id: I5e904c160c68805a8606a8b2d1ab4fb6172066e7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug.
Change-Id: I2dae22c0db294f5334d9796d90f432d6c8d304df
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The code for setting the LPC generic memory range uses an array of fixed
address ranges not needing explicit decoding, to decide if the address
needs to be written to the LGMR register. Most platforms only mistakenly
add the PCH reserved mmio range, that is not decoded generally,
effectively breaking the mechanism. Only APL uses the array correctly.
That code, in it's current state, does not work (except for APL) and
currently, there is not a single user. Thus, drop it before people start
using it.
Change-Id: I723415fedd1b1d95c502badf7b0510a1338b11ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I795b8da3c5e1efb51c8fe4673f025839a1c630bc
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I2f484d232a46214ff98168f41f96d56b047892e2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I67bdd9a96928b77a9a178afea7dab03dc370312c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I342b9217af0288a3b525e629aac791eb0f880442
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
We need to write some special values to key protection registers before
applying init_setting table and lp_setting table to PMIC. Otherwise,
those settings won't take effect.
After applying init_setting table and lp_setting table, we lock the
settings by writing zero to key protection registers.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I593d4e02bf0b62ac297957caf4ae1c1837f1f38d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Functionality depends of CMAP and CMBP references inside board
specific ASL implementation. Only roda/rk9 and roda/rk886ex has
that.
Change-Id: I4da8292375cb589d67dc68496b1e81971bc2a61f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49274
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Only amd/picasso and amd/stoneyridge have reference to
PCNT and that could be replaced with acpigen.
Remove the PCNT name from GNVS OperationRegion elsewhere.
Change-Id: I7dd45a840b3585fd24c31fd923b991c34ab4d783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000.
Change-Id: Ia6c2ee29e37040ea9b11505e9888c7f6f8da78bc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This memory is used for option roms and BIOS. This matches the ACPI
code.
Change-Id: I53dd4b967569889108352ca70086a12ce252e8e0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: I626989fa6625e0b3613a11e709c614d40a788b0e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: If4e05f496abc05e06a944b244824376f3937a57b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Chrome EC dropped strago support, so we need to disable it here
before updating our Chrome EC submodule.
Change-Id: Ied8905e995fd040b981ce18e95e225ade496d23c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48216
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Struct will be synced with picasso with followups.
Change-Id: I5f460cc3849bf1fad1f6da61169893488ccb2b40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48855
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use the function smbios_mainboard_version()
to query the board revision from the EC.
we need to select GOOGLE_SMBIOS_MAINBOARD_VERSION.
BUG=b:177818769
TEST=1. emerge-volteer coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Change-Id: I2474ee03845356d0775f6da25274f696ad33f935
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SoC code has in implicit dependency on this option, so select it in
the SoC code instead of the mainboard code.
Change-Id: Iea908c142f4a94a107cf74a31d9f5e29668d4b5b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the sasukette variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:175848514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKETTE
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I0a554efe0919dc2f5880f0f7817a37bd4be88ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change enables LTE modem for sasuke.
- Add LTE modem device into devicetree
- Add GPIO control for LTE modem power on and off
BUG=177177967
TEST=Built and verified modem device existence with lsusb
Change-Id: I34ba8ab00b73f24d1786ab014e9981b172a63a27
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49163
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Writing 0 to MSR IA32_BIOS_SIGN_ID before fetching this MSRs content
is required. This is how things are done in
cpu/intel/microcode/microcode.c.
The "Intel® 64 and IA-32 Architectures Software Developer’s Manual"
also recommends this: "It is recommended that this field be preloaded
with 0 prior to executing CPUID" (this field being %edx).
Change-Id: I24a87aff9a699ed8ab2598007c8b8562d0555ac5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DPTF paramerters from thermal team.
1. PL1 max =5.8W
2. PL1 min =3.8W
3. PL2 =20W
BUG=b:177249297
BRANCH=dedede
TEST=build image and verified by thermal team.
Change-Id: I19654b65613817ebecf979ce7ac4f76d370ebdc2
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update SMBIOS type 17 type detail. Define this field by module type.
Tested=Execute "dmidecode -t 17" to check type detail is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I6700056edad5db2b86f6da526329b1343b026385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested=On OCP Delta Lake, verify the VPD values can be read
correctly.
Change-Id: I1c27cb61cd52902c92b3733e53bc8e6fd6a5fe7f
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Given the lack of documentation for this platform, having this info
in coreboot logs (e.g. from board_status) can be pretty useful.
Change-Id: I6a743c1efc1b6da71589460a69bfe4785e3e77a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We found that the switch frequency of vgpu is at 4~5Mhz with high
current case (> 3.5A) and is at 2.5Mhz with low current case(< 2.8A).
The switch frequency of vgpu should be kept at 2.5Mhz.
The root cause is that phase config of vcore is not disabled, it will
affect the switch frequency of vgpu. Corret the phase setting at
initialization.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I48d3729302de9e3343dce79fe6f5ed045d0296a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49005
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After calibration, we can get ddr vendor id or density info from
MR5 or MR8, this helps to make sure the DDR HW is as we expected.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ie62948368716d309aab8149372b2b6093fc33552
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
It looks like we didn't care to reserve the VGA MMIO (a & b segments)
and the c..f segments, initially. It was probably never needed until
the new resource allocator that will make use of any unclaimed space.
Change-Id: Iebdae64914d9f8301cafc67a5aba933c11294707
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It is claimed getac/p470 has this implemented and not
as a TODO.
Change-Id: Ifa9ec5bcb8b25b6334b589e4bc7bcb915e85e349
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49349
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The layout of GNVS has expectation for a fixed size
array for chromeos_acpi_t. This allows us to reduce
the exposure of <chromeos/gnvs.h>.
If chromeos_acpi_t was the last entry in struct global_nvs
padding at the end is also removed.
If device_nvs_t exists, place a properly sized reserve for
chromeos_acpi_t in the middle.
Allocation from cbmem is adjusted such that it matches exactly
the OperationRegion size defined inside the ASL.
Change-Id: If234075e11335ce958ce136dd3fe162f7e5afdf7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 27af8a7e5d.
Reason for revert: This depends on CB:45517 which hasn't landed yet.
Change-Id: I2a6fbf54cfe01bf25e9ea8da84f6f2a17418f0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49647
Tested-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This will remove "CONFIG_FRU_DEVICE_ID=0" from ".config" when unused.
Change-Id: Ic50de165c1f3de3886d3cd1ae66853c9fad35ed2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
According ADL EDS to update the PCH and CPU PCIe RP table.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idcc21d8028f51a221d639440db4cf5a4e095c632
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
L1_substates_control is common define. Move out of soc level.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I54574b606985e82d00beb1a61cce3097580366a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Disable all NIDs other than those for the front combo jack.
Adjust attributes to match jack physical location, appearance, etc.
Correct group number for verbs for HDMI output.
Test: run hdajackretask, verify NID characteristics correct for each
verb. Verify headphone detection and output functional.
Change-Id: If9fca5d9795d56bd38c8ea47f8de985c14ac8fab
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49464
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case of CPU PCIe RPs, the RP numbers might not be contiguous for
all the functions in a slot.
Example: In ADL, RP1 is 00:06.0, RP2 is 00:01.0 and RP3 is 00:06.2 as
per the FSP expectations.
Hence, this change updates the defintion of `struct pcie_rp_group` to
include a `start` member which indicates the starting PCI function
number within the group. All common functions for PCIe RP are
accordingly updated to take the `start` member into account.
Thus, in the above example, ADL can provide a cpu_rp_table as follows:
{
{ .slot = PCIE_SLOT_6, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_1, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_6, .start = 2, .count = 1 },
}
Since start defaults to 0 when uninitialized, current PCH RP group
tables don't need to be updated.
Change-Id: Idf80a0f29e7c315105f76a7460c8e1e8f9a10d25
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49370
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a long time, second parameter 'stop' has been
ignored. The tested range is within 1 MiB above 'start'.
Change-Id: Icbf94cd6a651fbf0cd9aab97eb11f9b03f0c3c31
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48561
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the USB2 port 3/4/9
1. USB2 port3 assign to WWAN, and elemi have no WWAN.
2. USB2 port4/port9 connect to Type-C C1/C0
BUG=b:177483059
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I9affc69cc325b5eb0219b50bfe46f66eb0bb2016
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49473
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: Ie122a441145383b820d96e32ce1581dfc27fa57b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
They all operate on that file, so just add it globally.
Change-Id: I953975a4078d0f4a5ec0b6248f0dcedada69afb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Now that intermediate coreboot.pre manipulation is serialized within
the build system, remove the flock calls.
Change-Id: I8a767918aec5fcb7127ebb19ac46e58bed7967fb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We no longer need the IO-APIC assignments since we use the GNB IO-APIC.
We were also missing the E-H IRQ mapping. I also renumbered them since
IRQ 8 is used by the rtc.
TEST=none
BRANCH=zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia956ae457669aeda6fa49e127373aad3807f7b9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Two configuration files are added:
1. H9HCNNNFAMMLXR-NEE-8GB: new byte mode
2. MT53E1G32D2NP-046-4GB: new single rank mode
Also initialize the rank number field 'rank_num' for all configs.
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: I1786c1e251e8d6e110cbdce79feeb386db220404
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49108
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The fw_config field SPI_SPEED is not used for zork devices.
To define SAR config, use the fw_config bit[23..26].
Then vilboz can loaded different WiFi SAR table for different SKUs.
BUG=b:176858126, b:176751675, b:176538384
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5ba98799e697010997b515ee88420d0ac14ca7ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add code to collect all required information and generate ACPI CRAT
table entries. Publish tables generated from cb, rather than use the
tables created by FSP binary.
BUG=b:155307433
TEST=Boot trembyle and compare coreboot generated tables with tables
that FSP published previously.
BRANCH=Zork
Change-Id: If64fd624597b2ced014ba7f0332a6a48143c0e8c
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Based on voema schematics, two USB2 ports 3 and 5 are assigned to type C
connectors on Voema board.
BUG=b:177483061 b:172535001
TEST=Build and boot Voema.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I12cef85595e511801ab9c563ae4aa26e25875679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
Early gpio configuration was done in romstage, while LPC pads were
configured in bootblock. Instead of adding another dedicated gpio table
for bootblock, move early gpio configuration completely to bootblock on
these boards. This won't hurt, since there is no code touching the pads
in between.
The soc code gets dropped in CB:49410.
Change-Id: I2a614afb305036b0581eac8ed6a723a3f80747b3
Tested-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Command timing is the absolute value of the most negative `pi_coding`
value across all ranks, or zero if there are no negative values. Use the
MAX() macro to ease proving that `cmd_delay` can never be negative, and
then drop the always-false underflow check.
The variable type for `cmd_delay` still needs to be signed because of
the comparisons with `pi_coding`, which is a signed value. Using an
unsigned type would result in undefined and also undesired behavior.
Change-Id: I714d3cf57d0f62376a1107af63bcd761f952bc3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Clock is a differential signal and propagates faster than command and
control, therefore its timing needs to be offset with `pi_code_offset`.
It is also a periodic signal, so it can safely wrap around.
To avoid potential undefined behavior, make `clk_delay` signed. It makes
no difference with valid values, because the initial value can be proven
to never be negative and `pi_code_offset` is always positive. With this
change, it is possible to add an underflow check, for additional sanity.
Change-Id: I375adf84142079f341b060fba5e79ce4dcb002be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Commit 7584e550cc (nb/intel/sandybridge: Clean up program_timings)
introduced this condition along with a comment that says the opposite.
Command and clock timings always need to be computed, so drop both the
nonsensical condition and the equally-worthless corresponding comment.
Change-Id: I509f0f6304bfb3e033c0c3ecd1dd5c9645e004b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Basking Ridge is not ULT, thus does not support C-states deeper than C7.
Replace them with the values used by all other Haswell non-ULT boards to
allow subsequent commits to cleanly factor them out of the devicetree.
Change-Id: Ife34f7828f9ef19c8fccb3ac7b60146960112a81
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46907
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module is not expected to be powered off during warm reset. Hence
configure the LTE_PWR_OFF_ODL (GPP_A10) gpio pad reset configuration to
PWROK and set the TX state to 1.
BUG=b:163100335
BRANCH=dedede
TEST=Verified through the waveforms that power sequence is meeting the LTE module requirements.
Change-Id: I8676da6186559288aabe078b6158fc01075c7b41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Exit early if the chipset power state info isn't in CBMEM. Return -1 in
order to ensure the one caller of this function exits early as well.
Found-by: Coverity CID 1442304
Change-Id: Ifa42ba3024d3144de486d90ed7752820482549bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49359
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module used in metaknight has a specific power on/off sequence.
GPIOs related to power sequence are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: GPP_A10 keeps high, GPP_H17 goes low at least 2ms
Configure the GPIOs based on these requirements.
BUG=b:173671094
TEST=Build and boot Metaknight to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ibff16129dfe2f1de2b1519049244aba4b3123e52
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Use C-style comments everywhere, and follow the coding style.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I3ef96c5f6553ad50cee7d7f5614128b62a89e4ea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The caches have already been enabled during MP-init,
so these function calls are redundant. Remove them.
Change-Id: Ia9be1a3388d8e7c73c35a1c68b3dd5bc488658c2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix C code to match comment and assembly implementation.
Tested on Prodrive hermes:
The microcode spinlock is no longer used.
Change-Id: I21441299f538783551d4d5ba2b2e7567e152d718
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49304
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change affects Intel CPUs only. As most platforms are doing
uCode update using FIT, they aren't affected by this code either.
Update microcode in MP-init using a single spinlock when running on
a Hyper-Threading enabled CPU on pre FIT platforms.
This will slow down the MP-init boot flow.
Intel SDM and various BWGs specify to use a semaphore to update
microcode on one thread per core on Hyper-Threading enabled CPUs.
Due to this complex code would be necessary to determine the core #ID,
initializing and picking the right semaphore out of CONFIG_MAX_CPUS / 2.
Instead use the existing global spinlock already present in MPinit code.
Assuming that only pre-FIT platforms with Hyper-Threading enabled and at
most 8 threads will ever run into this condition, the boot delay is
negligible.
This change is a counterproposal to the previous published patch series
being much more unsophisticated.
Change-Id: I27bf5177859c12e92d6ce7a2966c965d7262b472
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Eaglelake MRC 2.55 does this, and also stalls for less time.
Change-Id: Iaaefd32c341a490e5c129df865407ec3f8da8212
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
To allow other platforms to reuse this code, extract it into a separate
compilation unit. Since HPET is enabled through the southbridge, place
the code in the southbridge scope. Finally, select the newly-added
Kconfig option from i82801gx and replace lpc.c `enable_hpet` function.
Change-Id: I7a28cc4d12c6d79cd8ec45dfc8100f15e6eac303
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On Coffee Lake systems prog_locate_hook() is called with PROG_POSTCAR.
For this reason the early check is not executed.
Add check for prog->type == PROG_POSTCAR, but execute
verified_boot_early_check() once.
BUG = N/A
TEST = Build and boot on Facebook FBG1701 and Intel CoffeeLake system
Change-Id: Ia3bd36064bcc8176302834c1e46a225937d61c20
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48852
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
make olddefconfig on other projects using USE_VENDORCODE_ELTAN results in error.
USE_VENDORCODE_ELTAN unmet direct dependencies.
Remove dependency on VBOOT for USE_VENDORCODE_ELTAN.
TEST = Build and boot on Facebook FBG1701
Change-Id: I5881c334955c73ae0f1a693f95ceb1aee62ee898
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
This struct isn't used anywhere else, so there's no need to name it.
Change-Id: I22eda07f14096d2b7400e6ab715641ffd68fbc08
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49444
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The default value is not sufficient to correctly configure the Type-C
ports as it has all ports disabled by default. On Volteer ports 0
and 1 are enabled so setting this value to 0x3 and correctly
keeping the IomPortPadCfg values at 0 for ports that have a
retimer and ports that are not configured. These values were set
to 0x90000000 to avoid s0ix issues which arose from the UsbTcPortEn
value being incorrect.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that s0ix cycles complete
without any issues
Change-Id: Ib4f2bd0f68debd4e97ccaab9e1d8a873dc4e4d9f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48814
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a requirement of TCSS this setting needs to be correctly set
to determine what Type-C ports are enabled on the platform. Without
this value correctly set there can be adverse effects on the other
TCSS specific values.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that S0ix cycles no longer
fail when the IomPortPad is set to 0
Change-Id: I6c5260cda71041439fe89d15bd3cafd4052ef1e7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
These are no longer really useful. We can also enable Power Resource
ACPI debug in the kernel if we want these messages.
BUG=none
BRANCH=zork
TEST=emerge-zork and verify debug messages are no longer posted
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I936e816266825f1c59377c2e079ffe1a5188838c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Target added to INTERMEDIATE all operate on coreboot.pre, each modifying
the file in some way. When running them in parallel, coreboot.pre can be
read from and written to in parallel which can corrupt the result.
Add a function to create those rules that also adds existing
INTERMEDIATE targets to enforce an order (as established by evaluation
order of Makefile.inc files).
While at it, also add the addition to the PHONY target so we don't
forget it.
BUG=chromium:1154313, b:174585424
TEST=Built a configuration with SeaBIOS + SeaBIOS config files (ps2
timeout and sercon) and saw that they were executed.
Change-Id: Ia5803806e6c33083dfe5dec8904a65c46436e756
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49358
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI part still needs some more code to be in place, so add that
later.
TEST=Together with the currently not merged rest of the amdfw patch
train applied this results in working serial console in bootblock in
Majolica.
Change-Id: Ia844e86a80c19026ac5b47a5a1e91c2553ea5cca
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49378
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the functions that get called by the coreboot console
initialization code aren't in the SOC-specific code anymore, the SOC's
uart.c can be included unconditionally in the build now. This also
replaces the STONEYRIDGE_UART Kconfig option with the common
AMD_SOC_CONSOLE_UART one.
Change-Id: I09c15566a402895d6388715e8e5a802dc3c94fdd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will result in less code duplication when the common AMD SoC UART
support gets used for more AMD SoCs.
Change-Id: Id1786f32324de3e3947d792c599e2019705c5a85
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49373
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This partially reverts commit 6f8f9c969b
by moving CONSOLE_UART_BASE_ADDRESS back to the SoC-specific code, since
the number and base addresses of UARTs turned out to be rather SoC-
specific. The help text for the AMD_SOC_CONSOLE_UART option also
contained those base addresses, so remove that as well.
Change-Id: I01211ec62421c56f22ed611313d6245a05bdea67
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The UARTs in the Picasso SoC are memory mapped, but there is also some
hardware support that isn't used by any board to make the UARTs behave
like the ones found on legacy x86 machines from the 90s.
In the MMIO mode the MMIO address of the UART controller is passed to
the OS via ACPI. The OS expects the base clock of the UART controller to
be 48MHz (see the cz_uart_desc struct in drivers/acpi/acpi_apd.c and
drivers/tty/serial/8250/8250_dw.c in the Linux kernel) in this case. It
is also possible to enable additional decodes from four 8 byte legacy
I/O locations used for serial ports to the different UART controllers,
which doesn't disable the MMIO access though. The legacy I/O-mapped
serial ports are usually expected to have a base clock of 16*115200Hz
which the hardware can also provide to the UART's baud rate generator.
So there are two possible valid configurations to use the UARTs; either
MMIO access in combination with a 48MHz base clock or the legacy I/O
decode with a ~1.8MHz base clock.
The existing code unconditionally generates ACPI objects for all enabled
UARTs, so those shouldn't be put into legacy mode and switching the base
clock to ~1.8MHz was only done in the case that the UART was used as
coreboot console UART which still used the MMIO access, but the lower
base clock. Since no board even selects this option and it's rather
invasive to properly implement this feature, just drop the corresponding
broken code.
TEST=SoC UART console still works on Mandolin.
Change-Id: I26fa8fdfc781b583ba56ac4dbcbbfb6100e84852
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49371
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is causing boot errors on zork:
coreboot-v1.9308_26_0.0.22-18590-g4598a7bed945 Wed Dec 16 17:32:25 UTC 2020 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area FW_MAIN_B found @ 312000 (3137280 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1f2bbdd9c87c4efdfb0042e90a20b489fa0efced
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
While unused, this allows use of a common initialisation
code for GNVS allocation.
Change-Id: Ie84b5a3e16d3baa12bcd5dadac0b1f7edb323272
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update PL1 min and max values for Delbin systems
BUG=b:168958222
BRANCH=None
TEST=Build and verify on delbin system
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: I2152f0dbeb0ae463b78464571b6c434830f0082a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
The S3/S4 workaround is specific to Panther Point stepping A0, and it is
wrongly implemented. Rewrite the whole function as per reference code.
Since this runs in SMM, be overly cautious and double-check everything.
Do not rely on GNVS to determine if xHCI is enabled. Instead, check
whether the corresponding bit in the Function Disable register is set.
Only Panther Point has xHCI, so exit early if this is not the case.
Change-Id: Iabce6c52fac781dc694f5b589fab2e9fe438f3f5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:174338903
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I875f6b32c4053ef6d23ad7606cd35a129a78c306
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49290
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change lets IOM consider all USB connected devices as device
attached(DA) scenario. While connecting a typec-to-a dongle, IOM would
disable TC cold and help to resolve enemuration failure after usb3
device is plugged into the dongle.
BUG=b:173054070
TEST=Build and boot on delbin.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0ad0322693b4f8fbf1000b24eb21dddcebec686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The name `..._index` is confusing since the maximum index of an array is
not `ARRAY_SIZE(array)` but `ARRAY_SIZE(array) - 1`.
Rename `uart_max_index` to `uart_ctrlr_config_size` to make the name
match the variable´s value.
Change-Id: I7409c9dc040c3c6ad718abc96f268c187d50d79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Initiate overridetree.cb based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I31e5ac1703476083ac71dac30b0a3299b38384c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Follow latest schematic to fill gpio table.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a983605b5139ff8510a0cf225e6564b9215cb1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Two USB2 ports 4 and 9 are assigned to type C connectors on Voxel board.
This update configures these USB2 ports for Type C which will allow USB2
port reset message upstream from PCH to CPU to recover a USB3 device
that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Voxel board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia370a449a41701e690c1c507d70bedfce2076a65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
It is only used in one place, and there's two other equivalent macros.
Change-Id: I7c8241e28f688abd2df8180559dd02ee441c7023
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Get rid of using eax and reload counter on race condition.
Change-Id: Ie4b9957d8aa1f272ff1db5caf2c69d1e1f086a03
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47714
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper function `pcie_rp_enable_mask()` that
returns a 32-bit mask indicating the status (enabled/disabled) of PCIe
root ports (in the groups table) as configured by the mainboard in the
device tree.
With this helper function, SoC chip config does not need to add
another `PcieRpEnable[]` config to identify what root ports are
enabled.
Change-Id: I7ce5fca1c662064fd21f0961dac13cda1fa2ca44
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48968
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the definition of config_of_soc() to a macro that
expands to __pci_0_00_0_config instead of accessing the config
structure by referencing the struct device. This allows linker to
optimize out unused portions of the device tree from early stages.
With this change, bootblock .text section size drops as follows:
Platform | Size without change | Size with change | Reduction |
---------------|---------------------|------------------|-------------|
GLK (ampton) | 27112 bytes | 9832 bytes | 17280 bytes |
APL (reef) | 26488 bytes | 17528 bytes | 8960 bytes |
TGL (volteer2) | 47760 bytes | 21648 bytes | 26112 bytes |
CML (hatch) | 40616 bytes | 22792 bytes | 17824 bytes |
JSL (waddledee)| 37872 bytes | 19408 bytes | 18464 bytes |
KBL (soraka) | 31840 bytes | 21568 bytes | 10272 bytes |
As static.h is now included in device.h which gets pulled in during
the unit tests, a dummy static.h is added under tests/include.
Change-Id: I1fbf5b9817065e967e46188739978a1cc96c2c7e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
By default, the HS400 mode of GL9763E is slow mode (150MHz).
Therefore, the slow mode is disabled for HS400 running at 200MHz.
For eMMCs such as Hynix (H26M74002HMR) on HS400, adjust the internal
Rx latch dealy of HS400 to have better compatibility.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: I84844c2432d4223d9929182c5c430915e52875b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The FW config takes 2 bits for USE_FAN[27,28].
So FW_CONFIG_SHIFT_WWAN value should be 29.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ica6d04f9c48aa0800189283608bf57416ac75cf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49236
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 542307b815 (broadwell: Add small delay before Flex Ratio reboot)
introduced a workaround for Broadwell. Implement it on Haswell as well.
Since this is only necessary when a TPM is present on a system, only do
the delay (which is not that small, to be honest) on TPM-enabled builds.
Change-Id: Id8b58e9fa2a1c81989305f5b4b765b82c01e1596
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46941
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 7f28e4ee01 (broadwell: Enable turbo ratio if available) is also
applicable to Haswell, since the MSR definitions are the same for both.
Change-Id: Ic5f30a5b06301449253bbfb9ed58c6b35a767763
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46918
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MSR only needs to be set when IO MWAIT redirection is to be enabled.
This was copied from Sandy Bridge, which already had this inconsistency.
Change-Id: I424333afd654db9a7e180e9a2c31d369e3d92fd6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46917
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:171757619
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I37390535e263b4b9547ad7307278e3360ba836bd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Booting on Kingston (EMMC64G-TA29/TX29-HP) and Hynix (H26M74002HMR) eMMC
currently fails due to R/W error. This is a workaround to finetune the
data latch timing by verdor-specific setting of GL9763E. For improving
the compatibility of GL9763E with these two eMMC.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Change-Id: Iddb145ed6a9edb2d7a50248e64659cda78b88ae6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
Change-Id: Icccd9d15a9e9a22c9bfe7a9843e95d77013c9c8f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49047
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi
- Linux tested on clevo/cml-u
Change-Id: I51fdf52419aa7f059b70a906fd8bdac88d5b6046
Tested-By: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49046
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for the Intel LPIT table to support reading Low Power Idle
Residency counters by the OS. On platforms supporting S0ix sleep states
there can be two types of residencies:
* CPU package PC10 residency counter (read from MSR via FFH interface)
* PCH SLP_S0 assertion residency counter (read via memory mapped
interface)
With presence of one or both of these counters in the LPIT table, Linux
dynamically adds the corresponding attributes to the cpuidle sysfs
interface, that can be used to read the residency timers:
* /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
* /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
The code in src/acpi implements generic LPIT support. Each SoC or
platform has to implement `acpi_fill_lpit` to fill the table with
platform-specific LPI state entries. This is done in this change for
soc/intel/common, while being added as its own compilation unit, so SoCs
not yet using common acpi code (like Skylake) can use it, too.
Reference:
https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi together with CB:49046
- Linux tested on clevo/cml-u, supermicro/x11ssmf together with CB:49046
Change-Id: I816888e8788e2f04c89f20d6ea1654d2f35cf18e
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:176536593
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wayne3_Wang <wayne3_wang@pegatron.corp-partner.google.com>
Change-Id: I69962a5b7c7c464280b35c834f7ee1c9b77db6fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49197
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a minimal chipset tree with only two devices:
1. Domain
2. GNB root complex
This allows sconfig to generate the config structure for SoC root
device that is used by config_of_soc().
Change-Id: I7e08ecf4b9556dc9325bd5a6a51566a949ceb73f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
This change updates various uart_* functions to use simple(_s_)
variants of PCI functions. This is done for a few reasons:
* __SIMPLE_DEVICE__ check can be dropped since the same data type can
be used in early stages and ramstage.
* Removes the requirement on early stage to walk the device tree to
get access to the device structure. This allows linker-based device
tree optimizations for early stages.
As part of this change, uart_get_device() is refactored and a new
function uart_console_get_devfn() is added which returns pci_devfn_t
in MMCONF format. It is then used directly by the _s_ variants of PCI
functions.
Change-Id: I344037828118572ae5eb27c82c496d5e7a508a53
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change renames `struct uart_gpio_pad_config` to `struct
uart_controller_config` and adds a new parameter devfn (which expects
devfn for the UART controller corresponding to the index in
PCI_DEVFN() format). This gets rid of the SoC callback to get `struct
device` pointer to the UART controller device.
Change-Id: Id0712a0038f2cc1a61b8b5a58fa155f14e7949a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49212
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
Tested by checking lspci output on System76 galp3-c (WHL), oryp5 (CFL),
and oryp6 (CML).
References:
- TigerLake FSP Integration Guide
- Intel Document Number 337868-002
Change-Id: Ieaa45ef7fa8e0da4a25b9174ded1ea0c5d9c4b4e
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49104
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Subrata Banik