The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(JEP106W), adds some device IDs and provides information about
non-conforming IDs.
The EON change is left to the patch adding EON chips.
This patch should have no effect on code generation.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
page size. Fix that. Page size is uniform 256 bytes for SPI.
A sector/block size field in struct flashchip would be nice, though.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
output is specified.
Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PC97317 has SID = 0xdf. PC87371/PC97371 do not seem to exist.
Signed-off-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2999 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing contributors to the README.
- Drop obsolete -D option from manpage.
- Only list contributors who added non-trivial amounts of code as copyright
holders (and do not list those who merely provided register dump support
for Super I/Os). Those contributors are still listed in the README,
of course. See discussion in the thread starting at
http://www.linuxbios.org/pipermail/linuxbios/2007-October/025516.html
- Make a function static.
- Fix incorrect URL in code comment. Drop obsolete comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Attached is a patch that enables AMD Geode CS5536 chipset support. I
have tested it successfully on a MSM800 board from digital logic.
Signed-off-by: Lane Brooks <lbrooks@mit.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a delay of 10 us after entering ID mode and this was insufficient for
the 29C020. The data sheet claims we have to wait 10 ms, but tests have
shown that 20 us suffice. Allow for variations in chip delays with a
factor of 2 safety margin.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Small cosmetic fixes (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2956 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is the common style in both Linux as well as in LinuxBIOS.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2922 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2904 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add support for the Fujitsu MBM29F400TC flash part.
Detection and reading works, writing is not tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.
So I created a very quick patch (attached).
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2897 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
making the output of "make -s" finally usable.. (still trivial, doesn't
change any logic or remove any code)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2894 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
status register instead.
This has been tested by Harald Gutmann <harald.gutmann@gmx.net> with a
MX25L4005 chip.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2876 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip the code was tested and verified with is the Macronix MX25L4005,
but other chips should work as well.
Timeouts are still hardcoded to data sheet maxima, but the status
register checking code is already there.
Thanks to Harald Gutmann for the initial code on which this is loosely
based.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the --dump option, it just means lots of additional work for no gain, IMO.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2872 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We often want to know the exact version number of superiotool which
was used to gather a certain output/dump.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Install binary in /usr/sbin (not /usr/bin), as it's a root-only tool.
- Rename manpage from flashrom.1 to flashrom.8, as section 8 contains
"System administration commands (usually only for root)".
- Actually install the manpage upon 'make install'.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2866 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Michael van der Kolff <mvanderkolff@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
has a slightly different format than that of the W83697UF/UG so we have
to hack around it a bit.
This patch has been verified to work on real hardware by
Idwer Vollering <idwer_v@hotmail.com> on IRC (thanks!).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2861 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Move SPI code out of board_enable.c where it started its life. The SPI
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2858 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2857 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of the Winbond chips from being detected (trivial fix).
This is verified on real hardware and works fine now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2855 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
went wrong in one of the recent commits.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2842 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, dump support for the NSC PC87351.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
about where to send additional register dumps.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2834 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: David Hendricks <david.hendricks@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2833 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
be detected, as it needs a non-standard init sequence.
Minor other fix: Drop incorrect 0x2b from LDN 5 of the ITE IT8705F.
Signed-off-by: Robinson P. Tryon <bishop.robinson@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2825 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add notes which IDs were taken from sensors-detect (as where we lack
datasheets, thus cannot verify them) and which we support but sensors-detect
does not (yet). I'll post patches on the lm-sensors list to sync up
the detected chips between superiotool and sensors-detect.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2824 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Improve the --verbose output a bit more. Print the "Probing..." text for
all Super I/Os and if a Super I/O is not known, show the data we were
able to read from the chip (what data this is is very vendor/chip specific).
* Thus the common no_superio_found() is dropped, it's not useful.
The "read from 0x20" part was wrong for all Super I/Os other than the
NSC ones anyway.
* Winbond: For the 'olddevid' only use bits 3..0, mask away the others.
* SMSC: Print which ID registers we try to read (in --verbose mode).
* Minor cosmetic fixes.
* Rename PC8374 to PC8374L (as per datasheet).
* Rename probe_idregs_simple() to probe_idregs_nsc().
* Rename dump_readable_ns8374() to dump_readable_pc8374l().
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2821 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The help implied that writes happen by default, which they don't. Fix
the text, and say something when we dont specify any commands.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
way. It introduces a generic SPI host driver for the IT8716F Super I/O
which will enable easy SPI programming without having to care for the
peculiarities of the SPI host.
To activate probing for the IT8716F, you have to use the gigabyte:m57sli
mainboard override. SPI support will then use the gathered SPI host data
to access the SPI flash.
This has been tested sucessfully by Ward Vandewege <ward@gnu.org> on the
GA-M57SLI v2.0, which has a MX25L4005 SPI flash part.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Make the -V output more informative.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2814 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Super I/Os from SMSC. Otherwise not all of them are detected (and there
could theoretically be _two_ of them in a system, so we should probe
for both types anyway).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to ITE IT8716F Super I/O. Right now this is hardcoded to the Gigabyte
M57SLI board. It works only with rev 2.0 of the board, but it will bail
out on earlier versions, so no damage can occur.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
dump support for the SMSC DME1737 and the ASUS A8000. Random minor fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2803 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
contents in human-readable form (e.g. "COM1 enabled" etc.) instead
of the hex-table format from -d / --dump.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add common 'enter configuration mode' function for most Winbond/Fintek/ITE
chips which use the 0x87 0x87 sequence for that reason.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2794 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pure luck (and broken code elsewhere). Needs some more fixing.
Add more LDN descriptions to various Super I/Os.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2793 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Minor coding style changes and code simplifications.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2791 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Various minor fixes and improvements (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2789 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
them. Reduce code duplication a bit by improved 'no dump available' handling.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
use different config ports.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2782 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Here's what a register dump looks like on my test system:
No Super I/O chip found at 0x002e
No Super I/O chip found at 0x004e
No Super I/O chip found at 0x002e
No Super I/O chip found at 0x004e
No Super I/O chip found at 0x002e
No Super I/O chip found at 0x004e
Super I/O found at 0x03f0: id=0x28, rev=0x01
SMSC FDC37N769
idx 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
val 20 90 80 f4 00 00 ff 00 00 00 40 00 0e 28 01 00 00 00 00 00 02 00 01 03 00 00 00 00 00 00 80 00 00 00 00 00 00 ba 00 00 03 00 00 23 03 03 00 00
def 28 9c 88 70 00 00 ff 00 00 00 00 00 02 28 NA 00 00 80 RR RR NA NA NA 03 RR RR RR RR RR RR 80 00 3c RR RR 00 00 00 00 00 00 00 RR 00 00 03 00 00
Probing 0x0370, failed (0xff), data returns 0xff
I'm self-acking this as it's pretty simple stuff, but please let me
know if anything could be improved here, or if you think this
is not trivial enough to warrant self-acking.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2781 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
generic, so that we can use it for other Super I/Os, too.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2779 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
all Super I/Os can (and should!) use this (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As there will be lots more supported Super I/Os soon, the file is
really getting way too big...
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2777 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-ack'ing this, as the origin of the code in udelay.c (and thus
the license and copyright owner) is pretty clear.
The code which is now in udelay.c was split out from flash_rom.c in r1428,
and flash_rom.c, in turn, has been around since the beginning and had a
'Copyright 2000 Silicon Integrated System Corporation' line as well as the
usual GPLv2-or-later license header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
project (being packaged by distros, among other things).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Flesh out Makefile with all the usual stuff, e.g. install targets etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2759 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rename it to superiotool while we're at it.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2758 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The default for LDN 5 (keyboard), index 0xF0 is not 0x00
but rather 0x08 as per datasheet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes minor coding style issues and prepares the table for supporting
more chips of the ITE IT87xx Super I/O family.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2750 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Common code sequences have been factored out, the code has been made
more generic, has better handling of corner cases and is actually much
shorter.
It also adds probing for almost all recent (since 1999) ITE Super I/O
chips to probe_superio. I did verify against all ITE datasheets
(including those not available any more) that the probing was
non-destructive.
For the ITE IT8712F, the complete configuration is dumped and as
comparison the default value from the data sheet is printed.
More information can be extracted easily, however this needs loads of
datasheet surfing.
This code has been tested extensively, dumping for other ITE chips will
follow as a separate patch.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2749 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The first byte of the flash chip was read at the start of the function
and later written back to address 0 if the flash chip was not identified
as SST28SF040, which means most of the time. This write caused corruption
of flash contents when verifying a SST49LF160C part.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M50FLW080B, M50FW080, M50FW016, M50LPW116, M29W010B flash chips made
by ST to flashrom.
The patch is based on the data sheets of the chips and has not been
tested at all.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only reading from the chips was tested; writing support is untested.
Thanks to Gürkan Sengün <gurkan@linuks.mine.nu> for testing!
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Same board enable as Asus A7V8-MX. Tested by Reinhard Max.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The previous code was pretty unreadable, undocumented and did some totally
unrelated things (such as mucking with the game port or port 0x92).
This version is tested with a 256 KB chip and should work for the
CS5530 and CS5530A.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Give decent names to virt_addr and virt_addr_2
* add some comments
* move virtual addresses to the end of the struct,
so they dont mess up the initializer.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2689 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The format specifier in the printf statements have been changed from
%08lx to %08llx or similar where uint64_t are being displayed.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2679 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Add support for the ALi M1533 to chipset_enable.c
* Add some SMBus poking needed for the ASUS P5A, to board_enable.c
Since PCI subsystem IDs are worthless with this board, people will
have to name the board directly.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2677 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
indent -npro -kr -i8 -ts8 -sob -l80 -ss -ncs *.[ch]
Some minor fixups were required, and maybe a few more cosmetic
changeѕ are needed.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* These helpers severely clear up winbond superio usage.
* Removed board_iwill_dk8_htx as it can be replaced by
board_agami_aruma (Mondrian Nuessle).
* Renamed board_agami_aruma to w83627hf_gpio24_raise.
* Clarified comments in w83627hf_gpio24_raise, and added
some things from the old iwill code.
* Moved all board functions name argument to const.
(warning breaks build)
* Moved iwill entry in board_pciid_enables.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2627 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to set the right GPIO pins, so write protection is disabled.
Signed-off-by: Mondrian Nuessle <nuessle@uni-mannheim.de>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it fixes. It seems many of the other boards run out of space for the
payload.
Thus, this patch only increases the image size for the three boards
- tyan/s2912
- nvidia/l1_2pvv
- gigabyte/m57sli
by adding a custom Config-abuild.lb file for each of them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Comment out code which currently doesn't compile. Needs fixing later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
instead of stdout (trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2610 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It shows the remaining space in an image now.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2604 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
all.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2603 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm guessing nobody has tried compiling it with 64bit userspace?
Patch makes it compile cleanly and stops a "SEGV instead of working"
issue.
I also added a few checks for errors on system calls.
Signed-off-by: Jeremy Jackson <jerj@coplanar.net>
Reworked and
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2602 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Drop empty file (0 bytes) northbridge/amd/amdk8/cpu_rev.c
and references to it.
* move config option decision to preprocessor instead of code
since config options can not change during runtime
* slightly more verbose output in built_opt_tbl.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Only open /dev/mem once and do it early.
* Drop extern for function prototypes.
* Minimize ts5300 impact in probe_flash()
This cleanup will making ICH7 SPI support quite some easier.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2585 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This splits up the ROM Write enable code into chipset specific and
board specific parts. This of course means that a lot of code is
plainly moved about.
* Allows for linuxbios name matching and pci-subsystem id matching.
The latter uses a double set to properly distuinguish boards despite
of some known vendors being lax about it.
* Fixes GPIO15 being raised on every VT8235 southbridge, regardless of what
that line actually controls; rom on EPIA-M, backlight on mitac 8999 laptop.
* Adds flashrom support for Asus A7V400-MX (KM400 + VT8235)
* Island aruma was renamed agami aruma, the board specific code now got
adjusted. A set of pci-ids was retrieved from source code.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2581 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashrom. 0x0360 is needed to support the DFI LANParty NF590SLI, and I
am deducing the others based on pci_ids.h in the Linux kernel.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2570 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Fix harmless but worrying warning where the return value of
pci_write_byte is misinterpreted.
* Hash together VT8231 and VT8235 code into VT823x. VT8231 is the better
implementation, but lacked the write protect disable code that's
apparently needed for VT8235.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2568 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: David Hendricks <david.hendricks@gmail.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2565 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is installed, but the test also fails if zlib-devel is missing. This
patch changes the error message accordingly.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2553 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
tree to make it compilable independant of the LinuxBIOS source code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2551 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* flash.h:
- add a license header
- add system definitions
* flash_enable.c:
- put io priviledge access in one single place
- add includes required for Solaris.
* lbtable.c, flash_rom.c, 82802ab.c:
- use MEM_DEV so it works on Solaris
* sst49lfxxxc.c, sharplhf00l04.c, sst_fwhub.c, 82802ab.c
- drop unneeded include to sys/io.h
* Makefile
- adapt to Solaris specifics.
Signed-off-by: Adam Kaufman <adam.kaufman@pinnacle.com>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Adam Kaufman <adam.kaufman@pinnacle.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2550 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2539 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also add suport for NVIDIA MCP55.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2537 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
into /usr/local/bin. Closes#54.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2524 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fixed write_page_write_jedec() in jedec.c. Added a check-reprogram loop
in the same function, to come around the high page write failure rate on
some boards.
This patch includes the changes suggested by Ron to simplify the control
flow.
It also includes trivial changes by me to make flashrom build on newer
systems (libpci needs libz now). I also made a small type case compile fix
and proper return code handling in one or two places.
Signed-off-by: Giampiero Giancipoli <gianci@email.it>
Signed-off-by: Ronald G Minnich <rminnich@gmail.com>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2505 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flash chips to flashrom (closes: #50).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2501 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and leaving enough room for a real payload (not /dev/null)
This is a wonderful example why "uses" sucks.
* add Config-abuild.lb for those boards that dont build with
the default settings and a real payload:
arima/hdama, amd/quartet, amd/serengeti_cheetah, ibm/e326
* if lzma is installed and a real payload is used, try compressing
it.
* fix a small bug in "abuild --help"
This patch is acked by me because its due to infrastructural changes only.
Flames welcome.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2496 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will detect any improper erase, closes#31
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2494 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add detailed instructions on how and where to get the datasheet,
its name, and order number (Closes#34).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2493 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on real hardware, reading, detecting and writing various chips works.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2489 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by Uwe Hermann <uwe@hermann-uwe.de>
X-Signed-Off-By: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2450 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
from Uwe Hermann <uwe@hermann-uwe.de>
X-Signed-Off-By: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2449 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by Roman Kononov <kononov195-lbl@yahoo.com>.
X-Signed-Off-By: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2448 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The make dependency rule for Makefile and Makefile.settings was completely broken. No way it ever worked.
OLPC buildrom flushed out this issue.
If you updated the Config.lb file in your target/<mfg>/<mainboard> directory and then switched to
target/<mfg>/<mainboard>/<target> and ran 'make' you would get a permission denied error due to the
make file trying to run 'config.py' directly rather than 'python config.py'
We never saw this because we always run target/buildtarget <target> and that sets up everything
correctly.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2373 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You may specify '-d bus:dev.func' or '-d dev.func'. If you do '-d <value>'
then the behavior reverts back to the orginal where <value> is taken to be
the 16-bit packed notation of busdevfn.
It also add a sanity check to try and detect when people have not specified
the -d option and they should have, or when the -d bus:dev.fn evals to a packed
busdevfn of 0x0000.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2271 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* https://openbios.org/roundup/linuxbios/issue99 - add ICH4-M support to flashrom
both from scott.tsai <AT> arima.com.tw
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2230 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Support for ATI SB400 (RS480 chipset)
* Support for Intel ICH7 (from Scott Tsai, scott.tsai <AT> arima.com.tw)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2229 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- support for flashing technologic system ts5300 SBC (needs -DTS5300 in
the makefile)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2205 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Make the error in buildrom a lot more informative -- how big are the
things that did not fit? it now tells you.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2162 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* do case insensitive comparison of mainboards, as wished on the
mailinglist
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2146 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Special version for HDAMA rev G with 33Mhz test and reboot out.
- Support for CPU rev E, dual core, memory hoisting,
- corrected an SST flashing problem. Kernel bug work around (NUMA)
- added a Kernel bug work around for assigning CPU's to memory.
r2@gog: svnadmin | 2005-08-03 08:47:54 -0600
Create local LNXI branch
r1110@gog: jschildt | 2005-08-09 10:35:51 -0600
- Merge from Tom Zimmerman's additions to the hdama code for dual core
and 33Mhz fix.
r1111@gog: jschildt | 2005-08-09 11:07:11 -0600
Stable Release tag for HDAMA-1.1.8.10 and HDAMA-1.1.8.10LANL
r1112@gog: jschildt | 2005-08-09 15:09:32 -0600
- temporarily removing hdama tag to update to public repository. Will
reset tag after update.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- optimize_link_read_pointers compiles now on the solo so don't disable it.
- Start sorting out the confusion between and object and an initobject on the ppc ports
- Major bugfix release of romcc to support to remove preprocessor deficiencies.
The line and column numbers are computed are now correct. But watch out
the error messages sometimes report the location of the next token so things
are still a little skewed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1784 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
crt0.S.lb: Modified so that it is safe to include console.inc
console.c: Added print_debug_ and frieds which are non inline variants of the normal console functions
div64.h: Only include limits.h if ULONG_MAX is not defined and define ULONG_MAX on ppc
socket_754/Config.lb Conditionally set config chip.h
socket_940.c We don't need and #if CONFIG_CHIP_NAME we won't be linked in if there are no references.
slot_2/chip.h: The operations struct need to be spelled cpu_intelt_slot_2_ops
slot_2/slot2.c: The same spelling fix
socket_mPGA603/chip.h: again
socket_mPGA603/socket_mPGA603_400Mhz.c: and again
socket_mPGA604_533Mhz/Config.lb: Conditionally defing CONFIG_CHIP_NAME
socket_mPGA604_800Mhz/chip.h: Another spelling fix
socket_mPGA604_800Mhz.c and again
via/model_centaur/model_centaur_init.c: It's not an intel CPU so don't worry about Intel microcode uptdates
earlymtrr.c: Remove work around for older versions of romcc
pci_ids.h: More ids.
malloc.c: We don't need string.h any longer
uart8250.c: Be consistent when delcaring functions static inline
arima/hdama/mptable.c: Cleanup to be a little more consistent
amdk8/coherent_ht.c:
- Talk about nodes not cpus (In preparation for dual cores)
- Remove clear_temp_row (as it is no longer needed)
- Demoted the failure messages to spew.
- Modified to gracefully handle failure (It should work now if cpus are removed)
- Handle the non-SMP case in verify_mp_capabilities
- Add clear_dead_routes which replaces clear_temp_row and does more
- Reorganize setup_coherent_ht_domain to cleanly handle failure.
- incoherent_ht.c: Clean up the indenation a little.
i8259.c: remove blank lines at the start of the file.
keyboard.c: Make pc_keyboard_init static
ramtest.c: Add a print out limiter, and cleanup the printout a little.
amd8111/Config.lb: Mention amd8111_smbus.c
amd8111_usb.c: Call the structure usb_ops not smbus_ops.
NSC/pc97307/chip.h: Fix spelling issue
pc97307/superio.c: Use &ops no &pnp_ops.
w83627hf/suerio.c: ditto
w83627thf/suerio.c: ditto
buildrom.c: Use braces around the body of a for loop. It's more maintainable.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Preprocessor constant expression evaluation is no long a special case so
unsigned long values can not be used.
- Undefined macros are not converted to 0. But a big warning is printed.
- Garbage at the of an #include directive is now done in tokens instead of
in characters.
This allows comments after an #include directive.
- Repaired a previously unnoticed regression in constant expression
evaluation. Logical expressions can now be evaluated again.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The static device tree is not built properly at all yet, but at least we get through it.
FIXME (What is the proper way to handle add in boards?)
- Add generic div64 support and ppc div64 support
- Fix abuild so it properly generates the CC line when cross compiling.
- Add one more possible ppc cross compiler target
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
generated Makefile has correct dependencies and is somewhat complete.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- add option to force rebuilds even if they were previously ok
- add option to build on target only
- play around
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1746 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ram linuxbios_ram instead of linuxbios_c and linuxbios_payload...
- Reordered the linker sections so the LinuxBIOS fallback image can take more the 64KiB on x86
- ROM_IMAGE_SIZE now will work when it is specified as larger than 64KiB.
- Tweaked the reset16.inc and reset16.lds to move the sanity check to see if everything will work.
- Start using romcc's built in preprocessor (This will simplify header compiler checks)
- Add helper functions for examining all of the resources
- Remove debug strings from chip.h
- Add llshell to src/arch/i386/llshell (Sometime later I can try it...)
- Add the ability to catch exceptions on x86
- Add gdb_stub support to x86
- Removed old cpu options
- Added an option so we can detect movnti support
- Remove some duplicate definitions from pci_ids.h
- Remove the 64bit resource code in amdk8/northbridge.c in preparation for making it generic
- Minor romcc bug fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix the hdama Config.lb to not longer use the link keywords oops,
and instead to have it nest everything properly.
- Update config.g to not support the link keyword
- update config.g to not support northbridge/southbridge/cpu/pmc noise words
we can just use chip now.
- Remove old link handling from the code
- Detect and handle duplicate paths so we generate one device with multiple links
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Set the bootstrap processor flag in the mptable.
- Implement 64bit support in our print statements
- Fix the reporting of how many cpus we are waiting to stop.
It is the 1 less than the actual number of cpus running.
- Actually enable cpu_initialization.
- Fix firstsiblingdevice in config.g
- Add IORESOURCE_FIXED to all of the resources set by config.g
- Fix the apic_cluster rule to add an apic_cluster path not an apic path.
- Add a div64.h to assist in the 64bit printf.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This includes more test cases
Lots of small bug fixes
A built in C preprocessor
Initial support for not inlining everything
__attribute__((noinline)) works
Better command line options and help
Constants arrays can be read at compile time
Asm statements that are not volatile will now be removed when their outputs go unused
Loads and stores that are not volatile will be removed when their values go unused
The number of FIXMES in the code is finally starting to go down.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1582 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. Exportable options ('export used') used to be exported if referred to in
a 'uses' statement. These options will now only be exported if the
option is set, or the default value is changed.
2. Options marked as 'export always' with no default value ('default none')
used to generate defines with no values 'export k8:='. This behavior
has changed so that the option will ONLY be exported if it has a value
assigned using 'set' or 'default'. Otherwise it is an error.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1467 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
than for loop. Please forgive me, I was too young 4 years ago.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1458 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
use standard product ID exit method for w49f002u
move udelay stuff into its own file
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1433 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. Options can only be set with 'option' statement in the target
configuration file. Options can be set as many times as needed.
2 Option DEFAULT values can be changed (or set) in any configuration file.
Changing a default value will display a warning message.
3. A default value is changed with the statement 'default <op> = <val>'.
4. Setting an option overrides the default value.
5. The 'mainboard' and 'arch' statements now set options implicitly. No
'uses' statement is required.
The idea is that parts will define default values for options that
they need/use. Option overrides are only done in the target file.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1258 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Support for compiling romcc on non x86 platforms
- new romc options -msse and -mmmx for specifying extra registers to use
- Bug fixes to device the device disable/enable framework and an amd8111 implementation
- Move the link specification to the chip specification instead of the path
- Allow specifying devices with internal bridges.
- Initial via epia support
- Opteron errata fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1200 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
- Updates to config.g so that it works more reliably and has initial support
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
killed src/sdram/generic_dump_spd.inc
killed src/sdram/generic_dump_spd.inc
- Updated the arima/hdama to build with the new configuration system
- Updated config.g to list all of the variables with make echo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1093 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cpu of a certain type and to eliminate the
cpu p5
cpu p6
cpu k7
nonsense in the old config files.
Next step is to hook into Eric's pci device stuff.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
device arrangement that can be statically configured during boot.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1058 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The object rules now have four members, this is getting KLUDGY!
[object, source, type (i.e. suffix), base]
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1006 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- SMP cleanups (remove SMP only use CONFIG_SMP)
- Minor tweaks to romcc to keep it from taking forever compiling
- failover fixes
- Get a good implementation of k8_cpufixup and sizeram for the opteron
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Moved payload into romimage
More flexible romimage declaration
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@983 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Greg help me, I've screwed up the tree, things are in there more than once, dammit!
screwup in partobj.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked the transformation into ssa form and now I catch all unitialized
variable uses.
- Several more test cases
- Bumped the version to 0.34
- Verified that -O2 the scc_transform now works.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@934 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
properly. And a few long standing bugs have been rooted out and removed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add several more test cases.
- Bump the version number to .32
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@919 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I set USE_FALLBACK_IMAGE to 1 in the top-level Config, but when it is tested
in arima/hdama/Config.lb, it is acting as though it is zero.
Also added a print command so it is easier to trace 'if' behavior.
Usage:
print "string"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@913 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more fixes to various Config.lb
one last problem and we're there
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Register allocator bug fixes.
* coalesce_live_ranges now also updates the interference graph of live instructions
* resolve_tangle now avoids copies to phi
* correct_tangles is now called in a loop so that all tangles get fixed
- Bug the version of romcc to 0.30
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add an additional consistency check to romcc and fix the more obvious problems it has uncovered
With this update there are no known silent failures in romcc.
- Update the memory initialization code to setup all 3 of the memory sizing registers properly
- In auto.c test our dynamic maximum amount of ram.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@885 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Minor romcc fixes
- In smbus_wail_until_done a romcc glitch with || in romcc where it likes
to run out of registers. Use | to be explicit that I don't need the short
circuiting behavior.
- Remove unused #defines from coherent_ht.c
- Update the test in auto.c to 512M
- Add definition of log2 to romcc_io.h
- Implement SPD memory sizing in raminit.c
- Reduce the number of memory devices back 2 to for the SOLO board.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Update apic.h to include the APIC_TASK_PRI register definition
- Update mptable.c to have a reasonable board OEM and productid
- Additional testfiles for romcc.
- Split out auto.c and early failover.c moving their generic bits elsewere
- Enable cache of the rom
- Fixes to amd8111_lpc.c so that we successfully setup virtual wire mode on the ioapic
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implementation of fallback/normal support for the amd solo board
- Minor bugfix in romcc
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Carl-Daniel Hailfinger