Use common P2SB driver. This is needed to address a problem when
enumerator does not see p2sb device (since it is hidden) but it
is active and BAR is decoded.
Change-Id: I9cb821a5684f15f1e1486872bf806a6ee3d0676f
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40920
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:152019429
BRANCH=None
TEST=1. provision dram_part_num field of CBI
2. modify mainboard - dedede to report DRAM part number from CBI
3. check DRAM part number is correct in SMBIOS for memory device
Change-Id: I509d06a81bd005c5afe6e74a2da2ca408dee7b29
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Fix FSP CAR on platforms that have ROM_SIZE of 32MiB.
CodeRegionSize must be smaller than or equal to 16MiB
to not overlap with LAPIC or the CAR area at 0xfef00000.
Tested on Intel CFL, the new code allows to boot using FSP-T.
Change-Id: I4dfee230c3cc883fad0cb92977c8f5570e1a927c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Unlike prior AMD devices, picasso cannot rely on the cache-as-RAM
setup code to properly enable MTRRs. Add that capability to the
bootblock_c_entry() function. In addition, enable an MTRR to cache
(WP) the flash boot device and another for WB of the non-XIP bootblock
running in DRAM.
BUG=b:147042464
TEST=Boot trembyle to payload and make sure bootblock isn't abnormally
slow.
Change-Id: I5615ff60ca196e622a939b46276a4a0940076ebe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38691
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: Iad0ba94fea019623a5b98fff0cb4a2cd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot jslrvp with NVMe
Change-Id: Iad0b394fea019223a5b98fff0cb4a2bd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Add support to generate ACPI operations to get/set/clear RX/TX GPIOs.
BUG=b:152936541
TEST=Build and boot the mainboard. Ensure that there are no errors in
the coreboot logs regarding unsupported ACPI GPIO operations.
Change-Id: Ibc4846fbd9baf4f22c48c82acefed960669ed7d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change enables support for em100 for Picasso platform. Since
em100 requires lower SPI speed, this change configures speed in all
modes as 16MHz.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that em100 works fine on trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib5ea1fe094fda9b8dba63e94b37e61791629564f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40825
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds options to allow mainboard to configure SPI speed for
different modes as well as the SPI read mode.
BUG=b:153675510,b:147758054
BRANCH=trembyle-bringup
TEST=Verified that SPI settings are configured correctly for trembyle.
Change-Id: I24c27ec39101c7c07bedc27056f690cf2cc54951
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Rob Barnes <robbarnes@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40421
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper sb_spi_init() that makes all the required
calls for configuring SPI to ROM.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic5b395a8d3bdab449c24b05d1b6b8777e128b5e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40824
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds enums for spi_read_mode and spi100_speed in
preparation for adding these to chip.h in follow-up CLs. This makes it
easier to reference what the mainboard is expected to set for these
SPI configs.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7f9778b41bd059a50f20993415ebd8702a1ad58e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40823
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
southbridge.h does not really need chip.h. So, this change removes the
inclusion of chip.h from it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I09c87b975ecd5f7798da8dd858be0c729aef42de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40822
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 285975dbba.
Reason for revert: VB2_RECOVERY_TRAIN_AND_REBOOT was never meant to have
any special effect on memory training behavior. It was just supposed to
be a "reboot automatically after reaching kernel verification" recovery
reason. On x86 devices this was used to prime the separate recovery
MRC cache in the factory (make sure it is initialized before shipping).
This isn't used on Kukui anyway, but in order to make sure nobody copies
this code and keep the behavior consistent between platforms, let's
remove it.
Change-Id: I5df5e00526e90cb573131de3c8bac9f85f4e3a5f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40623
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It seems that all SC7180 boards we have can well handle 37.5MHz of SPI
flash speed, so bump that up from the current 25MHz so that we don't
leave boot speed on the table. (The next step would be 50MHz which
currently doesn't work on all boards so we're not going there yet.)
BUG=b:117440651
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id6e98fcbc89f5f3bfa408c7e8bbc90b4c92ceeea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Check SPD is not NULL before print. This can prevent the system
from hanging up.
BUG=b:154445630
TEST=Check NULL SPD is not print.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iccd9fce99eda7ae2b8fb1b4f3c2e635c2a428f04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40560
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a Kconfig option PSP_UNLOCK_SECURE_DEBUG which
when enabled includes secure debug unlock blobs and sets the required
softfuses and options for amdfwtool. By default this is set to 'N'.
BUG=b:154880818
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I47d8af67989b06242d662c77b7d9db97f624edd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change updates Makefile.inc to use a helper function set-bit to
set a bit for the soft fuses. It gets rid of the different checks that
were done to set soft fuses to magic values in different places.
This is still not the best way to handle the fuses and instead this
logic should be embedded within the amdfwtool by making it aware of
specific platforms. But until that happens, we want to avoid having to
add PSP_SOFTFUSE setting in various places with different values.
BUG=b:154880818
TEST=Verified that the softfuse values are same with and without this
change.
Change-Id: I73887eb9c56ca5bb1c08d298fa818d698da1080b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40700
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the PSP Kconfig options that are prompted to the user should
really be selected by mainboard. This change updates such options to
not make them user-visible any more.
BUG=b:154880818
Change-Id: Iaff02fb1e720e0562b740799593322e59b022212
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
PSPTRUSTLETS_FILE was including a binary for fTPM which according to
BIOS architecture design guide is the firmware enabled TPM. Chrome OS
does not really use firmware enabled TPM. Also, this is an option
which is mainboard dependent.
This change drops the addition of PSPTRUSTLETS_FILE to PSP
directory. If this is something that is required by any mainboard,
there should be a separate Kconfig to include the required files.
BUG=b:154880818
TEST=Verified that trembyle still boots
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Iaa2126c879986d00c921c85fb5cb5257c7065006
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change drops the addition of PUBSIGNEDKEY_FILE to PSP
directory. This file is used to add OEM key for BIOS, however this is
currently unused for upcoming zork board. In the future, if any
mainboard needs this, it can be added based on some Kconfig selection.
BUG=b:154880818
TEST=Verified that trembyle still boots up fine.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Icd97856a94a100898678702d99bbe29b82956004
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40682
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Inclusion of MP2 firmware is optional and dependent on mainboard. Set
default option for including MP2 firmware in PSP directory to 'n'.
BUG=b:154880818
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I1ff7527a409d8ac7f4d30e69eafc53975b63e49b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change adds support in common block HDA driver to add a PCI
device for HDA in SSDT and removes the HDA device from DSDT for
Stoneyridge and Picasso.
_INI method is still retained in stoneyridge since I am unsure why it
was added. In order to support the _INI method, HDA driver makes a
callback hda_soc_ssdt_quirks() to allow SoCs to add any quirks
required for the HDA device. This callback is implemented by
Stoneyridge to provide the _INI method which retains the same
functionality for HDA device.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769,b:155132752
TEST=Verified that audio still works fine on Trembyle.
Change-Id: I89dc46b92fdcb785bd37e18f0456935c0e57eff5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40785
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
_INI method for AZHD device for Picasso family was just copied from
Stoneyridge as part of initial change. There is no evidence that this
is required for Picasso. Also, removing the _INI method works
perfectly fine. Thus, this change drops the _INI method for AZHD
device on Picasso.
Since the _INI method was the only entity using the OperationRegion
fields, this change also drops the operation region.
BUG=b:155132752
TEST=Verified that audio still works on Trembyle
Change-Id: If42abf91ee5cd47a881b0a3b4ca1916ea5169261
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40782
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds .acpi_name() callback to HDA driver that returns
"AZHD" as the ACPI device name for HDA controller. Since this is now
done by the common HDA driver, this change also removes the HDA device
name returned by stoneyridge in chip.c.
BUG=b:153858769
Change-Id: I89eaa799518572f3c46c7ce9ef8dd3f85daa12bb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40781
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a cosmetic change to use tabs to align hda_audio_ops and
hdaaudio_driver entries.
Change-Id: I8e398706cbe7087d0178b2433606f8984651c0d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40780
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change sets ops_pci for hda_audio_ops to default pci_dev_ops_pci
and removes the custom lops_pci since the driver does not really need
a custom ops_pci.
BUG=b:153858769
Change-Id: I4b46e22ef556c0f49152c41a07f3c54c513ae37a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40779
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCI device PCI_DEVICE_ID_AMD_FAM17H_HDA0 does not really use the same
vendor ID as PCI_VENDOR_ID_AMD. Thus, drop this device from the list
of pci_device_ids[] that are supported by the common hda driver.
BUG=b:153858769
Change-Id: If41dc7179e1e5b476878ee24c8a355b1cde762eb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40778
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original plan for Picasso was to combine the features of bootblock
with romstage due to its unique way of coming out of reset. Early in
development, all bootblock support was removed from the directory.
All Picasso designs will now use a bootblock as their first stage. The
reason being that it requires less invasive changes than using a hybrid
romstage.
Add a basic bootblock back to the directory, and compatible with the
design of lib/bootblock.c. The files support RESET_VECTOR_IN_RAM
and add appropriate settings in Kconfig. Make Makefile.inc calculates
the size and base of bootblock from known parameters.
* Future work may attempt to streamline this further, in conjunction
with changes in amdfwtool. See b/154957411.
BUG=b:147042464, b:153675909
Change-Id: I1d0784025f2b39f140b16f37726d4a7f36df6c6c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37490
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds GPID, a helper method to look up GPIO community ID for
an index.
This patch also includes Intel's common GPIO ASL code. CGPM method in
the common code uses the GPID method introduced in this patch.
BUG=b:148892882
BRANCH=none
TEST="BUILD volteer and ripto"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Id6a00fb8adef0285d6bbc35cd5a44539bd3be6b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40478
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds CGPM, a helper method to configure GPIO power management
bits that are part of miscellaneous config. This is needed for
configuration of these bits on S0ix entry and exit.
BUG=b:148892882
BRANCH=none
TEST="BUILD volteer and ripto"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Iac3a269d3071eb5d4100d516249eeb5ce23c02fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40260
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change sets .ops_pci for sata device_operations to default
pci_dev_ops_pci. It is required to set the subsystem IDs making the
behavior consistent with default_pci_ops_dev.
BUG=b:153858769
Change-Id: I695ac8961c92a3061beca890f5d47413b251e22b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40777
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables the use of AMD common block SATA driver for
Picasso. Since the common driver provides ACPI device name and PCI
device for SATA in SSDT, these are removed from picasso chip.c and
sb_pci0_fch.asl.
BUG=b:153858769
TEST=Verified that "STCR" device is correctly reported on trembyle in
SSDT.
Change-Id: Icfdcf9f5e08820b565aa9fcdd0cdc7b5c9eadcd5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40770
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support in common block SATA driver to add a PCI
device for SATA in SSDT and removes the SATA device from DSDT.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769
Change-Id: I16ac36d997496ff33c5b44ec9bd2731b2b8799eb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40769
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds .acpi_name() callback to SATA driver that returns
"STCR" as the ACPI device name for SATA. Since this is now done by the
common SATA driver, this change also removes the SATA device name
returned by stoneyridge in chip.c.
BUG=b:153858769
Change-Id: I5e0998be3016febbb3b0e91940750a38edb6a9e7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40768
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a cosmetic change to use tabs to align sata_ops and
sata0_driver entries.
Change-Id: Ia9eabd0cd64ecc9cbff0d4c3e3c6b71bbf29e3a9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40767
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
sata.c was being added to ramstage based on the selection of
CONFIG_SOC_AMD_COMMON_BLOCK_HDA which is not correct. This change
fixes the error by including sata.c based on selection of
CONFIG_SOC_AMD_COMMON_BLOCK_SATA.
BUG=b:153858769
Change-Id: I5d23e5817872ddbb3d8d4f7dcabbaafcee4d51f4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40766
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pointer passed to print_spd_info() from meminit.c needs to be
dereferenced first, so this change dereferences it.
BUG=b:154352883
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, login to kernel and execute the following cbmem command:
localhost ~ # cbmem -c | grep LPDDR4X
and verify it returns "SPD: module type is LPDDR4X"
Change-Id: I5ff64121f0d50947c4946e9e02460dfb7319d01a
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
.acpi_inject_dsdt() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
acpi_inject_dsdt as const.
Change-Id: I3b096d9a5a9d649193e32ea686d5de9f78124997
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40711
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.acpi_fill_ssdt() does not need to modify the device structure. This
change makes the struct device * parameter to acpi_fill_ssdt() as
const.
Change-Id: I110f4c67c3b6671c9ac0a82e02609902a8ee5d5c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40710
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
intel_igd_get_controller_info() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
intel_igd_get_controller_info() as const.
Change-Id: Ic044a80e3e2c45af6824a23f3cd0b08b94c0f279
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
sd_fill_soc_gpio_info() does not need to modify device
structure. Hence, this change makes the struct device * parameter to
this function as const.
Change-Id: I237ee9640ec64061aa9ed7c65ea21740c40b6ae2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
dw_i2c_soc_dev_to_bus() does not need to modify the device
structure. Thus, this change makes the struct device * parameter to
dw_i2c_soc_dev_to_bus as const.
Change-Id: Ibf5c8d8127dff2ab2ccbd1f6b4f553e98e81955f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40704
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.write_acpi_tables() should not be updating the device structure. This
change makes the struct device * argument to it as const.
Change-Id: I50d013e83a404e0a0e3837ca16fa75c7eaa0e14a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change:
1. Adds PCI device for graphics controller in ACPI SSDT tables using
acpi_device_write_pci_dev().
2. Gets rid of IGFX device from picasso acpi/northbridge.asl.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769
Change-Id: I3a967cdc43b74f786e645d3fb666506070851a99
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change selects common block graphics driver for Picasso and also
adds PCI ID for Family 17h graphics controller to the graphics
driver.
Since the common driver provides .acpi_name() callback for graphics
device, soc_acpi_name() no longer needs to provide the ACPI name for
graphics device.
BUG=b:153858769
Change-Id: Id3ffcb05d8f8a253a0b27407d52d7907c507cabb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds a common graphics block device driver for AMD
SoCs. In follow-up CLs, this driver will be utilized for Picasso.
This driver is added to enable ACPI name and SSDT generation for
graphics controller.
BUG=b:153858769
Change-Id: I45e2b98fede41e49158d9ff9f93785a34c392c22
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change adds all the missing PCI device IDs for AMD Family
17h. IDs that were already present are updated to include _FAM17H_ in
the name instead of _PCO_ and _DALI_. This ensures that the PCI IDs
match the family and models as per the PPR. In cases where the
controller is present only on certain models, _MODEL##H_ is also
included in the name.
BUG=b:153858769
BRANCH=None
TEST=Verified that trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ia767d32ec22f5e58827e7531c0d3d3bac90d3425
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
IOMMU for AMD Family 17h Model 10-20h uses the same PCI device ID
0x15D1. This change updates the name to indicate that the PCI device
ID is supported for FP5(Model 18h) and FT5(Model 20h).
BUG=b:153858769
BRANCH=None
TEST=Trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I17c782000ed525075a3e438ed820a22d9af61a26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Set SPD array NULL if no DIMM present. do_smbus_read_byte returns
negative value if SMBus transaction fails.
BUG=b:154445630,b:151702387
TEST=Check SPD is NULL if no DIMM in the slot.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie81adbfab5bb1d5c557fe549a158cb68e26b1162
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to doc 621880, it suggests setting 40 ohm in byte 185 in extCSD.
This commit provides _DSM method for driver to query driving strength.
TEST=mmc extcsd read |grep HS_TIMING and found bit[7:4] is set to 4
BUG=b:154159888
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I1b4df8b0d1d2cad3a7f521ad47ee5a4b3320c767
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Populate SMBIOS type 17 tables using data from SPD and read via IOSF.
Refactor print_dram_info() to pass thru SPD data and channel/speed info.
Move call to print_dram_info() after cbmem initialization so the SMBIOS
data has somewhere to go.
Test: build/boot google/swanky, verify via dmidecode.
Change-Id: I1c12b539c78d095713421b93115a4095f3d4278d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For DDR4, FSP expects channel 0 to set SPD for index 0 and channel 1
to set SPD for index 4. This change adds a helper macro to translate
DDR4 channel # to the index # that the FSP expects.
BUG=b:154445630
TEST=Verified that memory initialization for DDR4 is successful.
Change-Id: I2b6ea2433453a574970c1c33ff629fd54ff5d508
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Assuming given system is populated with multiple CPUs of same SKUs,
calculate number of threads based on MAX_SOCKET.
This is a stop gap solution until proper way of identifying total
number of sockets is determined.
Change-Id: I7ebad3d57c47b9eeb7d727ffb21bc0a1a84734fd
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Currently FSP-M does not implement the spec completely, e.g it is unable
to use user-provided heap location in CAR. While this is being resolved,
this workaround is a stop-gap solution that allows multi-socket usage.
TEST=tested on OCP Sonora Pass EVT and Intel Cedar Island CRB
Change-Id: Ia2529526a8724cf54377b0bd2339b04fa900815a
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40555
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We need to allow motherboards to configure certain parameters that
are specific to it. Hence, invoke this function. Also, provide a
weak motherboard implementation that does nothing.
Change-Id: Ifa2824811273236a66e742404856fbe17d4cf496
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40552
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I2C0&1 are either not available or not functional. Add place holders
instead, so that the array index matches the I2C controller number. I2C4
is slave device only, so do not initialize it as I2C host controller.
Also do some slight refactoring.
BUG=b:153152871
BUG=b:153675916
Change-Id: I397b074ef9c14bf6a4f6680696582f5173a5d0d3
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Paul Ma <magf@bitland.corp-partner.google.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1897071
Reviewed-on: https://chromium-review.googlesource.com/2057468
Reviewed-on: https://chromium-review.googlesource.com/2094855
Reviewed-on: https://chromium-review.googlesource.com/2149870
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40247
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When CONFIG_SEPARATE_VERSTAGE=n, all verstage code gets linked into the
appropriate calling stage (bootblock or romstage). This means that
ENV_VERSTAGE is actually 0, and instead ENV_BOOTBLOCK or ENV_ROMSTAGE
are 1. This keeps tripping up people who are just trying to write a
simple "are we in verstage (i.e. wherever the vboot init logic runs)"
check, e.g. for TPM init functions which may run in "verstage" or
ramstage depending on whether vboot is enabled. Those checks will not
work as intended for CONFIG_SEPARATE_VERSTAGE=n.
This patch renames ENV_VERSTAGE to ENV_SEPARATE_VERSTAGE to try to
clarify that this macro can really only be used to check whether code is
running in a *separate* verstage, and clue people in that they may need
to cover the linked-in verstage case as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2ff3a3c3513b3db44b3cff3d93398330cd3632ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add Type-C subsystem power management support for RTD3.
BUG=b:140290596
TEST=Include "tcss.asl" in platform "dsdt.asl" for coreboot build
with the firmware CM. Added acpi debug and booted to kernel. Probed
devices PM_STATE transition from D0 to D3 entry/exit while system at S0.
TBT PCIe root ports: 00:07.0/00:07.1/00:07.2/00:07.3, offset:0xA4, PM_STATE:D3HT.
xhci:00:0d.0, offset:0x74, PM_STATE:D0D3.
dma:00:0d.2/00.0d.3, offset:0x84, PM_STATE:PMST.
Verified xhci/dma/pcie root ports power runtime_status to be suspended and suspended
time tick through /sys/bus/pci/devices/bus:device:func/power.
Change-Id: I127d3700ad426a44639ee93b4477be6638b42e1b
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This implements the SPI driver for the QUP core.
Change-Id: I86f4fcff6f9537373f70a43711130d7f28bd5e09
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36517
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This implements the UART driver in SoC
Developer/Reviewer, be aware of this patch from Napali:
https://review.coreboot.org/c/coreboot/+/25373/78
Change-Id: I6494daa108197c030577ac86dab71f9ca6c21bdb
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35500
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The frequency to be used by UART client is 7.3728MHz, thus define it in
the clock header to be used by the driver.
Tested: UART frequency request by client driver.
Change-Id: I1ced350fe9826ea05b03ffc11aced2c21fe85c9e
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Remove explicit setting of iDisp Link parameters. These settings are
related to configuration for the link between HD-Audio controller and
Display unit for purposes of HDMI/DP Audio playback. During PO,
observed that without setting these params display part was not
binding. With the latest code verified that we dont need to explicitly
set these parameters anymore. HDMI/DP audio playback works fine with
default settings.
BUG=b:151451125
BRANCH:none
TEST= build and boot volteer/ripto and verify HDMI/DP audio playback
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie003d119918d363e2ff9172936b70416fd73c7f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40263
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jairaj Arava <jairaj.arava@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Changing the local pointer "start" has no effect.
Changing the value it points to has.
Change-Id: I1b689896fcf255b795b27d7a7163849d6dfdb00e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds _DSM Method in LPIT table for entering and exiting
S0ix. This method get injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
BUG=b:148892882
BRANCH=none
TEST="BUILD"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib58f2e33a33bac9cc5f6aca28e85a8066413a5cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
The error message has been copy-pasted across various functions, so it
is nearly impossible to know which function printed it. So, use __func__
to print that information.
Change-Id: I55438c2b36cc3b21f3f168bf98b0aca5fd50bbbc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40446
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allocate storage for the BERT reserved memory in cbmem, and add it in
response to a romstage hook. Add a Kconfig option for adjusting the
size reserved. This is different from the Stoney Ridge implementation
where it was intentionally oversized to ease MTRR use and to keep TSEG
aligned.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4759154d394a8f5b35c0ef0a15994bbef25492e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38694
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tigerlake platform does not have built in eMMC/SD support so all
this code is unused and can be removed.
Change-Id: I70ff983d175375171d5a649378f32f1062c0876d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The eMMC/SD interface is not present in all Intel platforms so this
change removes the default enable for the storage controller and
instead enables it in the specific SoCs that do provide it.
Currently this includes all platforms except Tigerlake.
Change-Id: I8b6cab41dbd5080f4a7801f01279f47e80ceaefd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Adds a new macro that allow to set the DRIVER or ACPI as host software
ownership for the GPI pad using the parameter own. Thus, this macro can
define more variants for pad configuration than others.
This is necessary to describe in more detail the configuration for the
Tioga Pass OCP server [1] and other boards. In addition, these changes
will be used to automatically generate macros [2] and great simplify
this task.
[1] https://review.coreboot.org/c/coreboot/+/39427
[2] https://review.coreboot.org/c/coreboot/+/35643
Change-Id: I9c191fb6935e94da6e296f8fee0b91a973534e1a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
psp_print_cmd_status only needs data from the mbox buffer header and not
the whole buffer. This avoids type casts when the buffer type isn't
mbox_default_buffer.
BUG=b:153677737
Change-Id: I8688b66fefe89fc4f3ce2207d4360ceb2dbaef12
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40412
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement the MboxBiosCmdSmmInfo function to inform the PSP of the SoC's
SMM configuration. Once the BootDone command is sent, the PSP only
responds to commands where the buffer is in SMM memory.
Set aside a region for the core-to-PSP command buffer and the
PSP-to-core mailbox. Also add an SMM flag, which the PSP expects to read
as non-zero during an SMI.
Add calls to soc functions for the soc to populate the trigger info and
register info (v2 only).
Add functions to set up the structures needed for the SmmInfo function
in Picasso support. Issue a SW SMI, and add a new handler to call the
new PSP function.
BUG=b:153677737
Change-Id: I10088a53e786db788740e4b388650641339dae75
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add C621A, C627A and C629A SKU IDs. C621A is used in the Whitley Product.
We need to add device ID for setting LPC resources.
Refer to Intel C620 series PCH EDS (547817).
Change-Id: I19a4024808d5aa72a9e7bd434613b5e7c9284db8
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40395
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new psp.c file so the base address can be determined, and select
the common/block/psp feature.
BUG=b:153677737
Change-Id: I322fd11a867a817375ff38a008219f9236c4f2ea
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://chromium-review.googlesource.com/2020368
Tested-by: Eric Peers <epeers@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40296
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This function is only needed and valid for the 1st generation PSP
interface used on stoneyridge.
BUG=b:153677737
Change-Id: Ia1be09c32271fe9480a0acbe324c4a45d8620882
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
TCSS TBT PCIE root ports scope type was mistakenly set to PCI_ENDPOINT.
Fix the scope type to be PCI_SUB.
BUG=b:141609884
TEST=Booted to kernel and verified no TBT PCIE root ports scope
type mismatch error in kernel log.
Change-Id: I844e7e9583992be496223fb51f24c5aa24fc7d21
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Provide the option to disable XHCI LFPS power management.
If the option is set in the devicetree, the bits[7:4] in
XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated
from default 9 to 0.
BUG=b:146768983
BRANCH=None
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: Ic603e3b919d8b443c6ede8bb5e46e2de07fcb856
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: I7ba635f5504ba288308d7d7a4935f405f289aa8d
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a function to dump ME Host Firmware Status registers.
In tigerlake, Manufacturing mode is “No” if below conditions are satisfied, indicating
end of manufacturing. Otherwise, manufacturing mode is "Yes".
1. Intel fuses are programmed (Indicated by HFSTS6[30] bit set)
2. The SPI flash descriptor region is locked. (Indicated by HFSTS1[4] cleared)
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: I831a51f9f482425bd3b97ef1d2404b1d06844d07
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Make use of print_me_fw_version() which is defined in the CSE lib to
print ME firmware version information for icl,tgl.
BUG=None
BRANCH=None
TEST=Build and boot iclrvp, tglrvp boards.
Change-Id: Ief75403c490eee499a84372e54fa38ea3016cc11
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add LTR and AER configuration to the root ports config.
BUG=b:151166040
TEST= build and boot volteer and check LTR and AER value
from FSP log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I668f2e5fea15019a9e5ae06fb4d55fa2aea69e8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40262
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the revision 4 FADT fields were already updated to ACPI
spec revision 6, but not all of them. In addition the advertised
FADT revision was 3.
Implement all fields as defined in version 6 and bump the advertised
FADT revision to 6.
Also set all used access_size fields and x_gpe0_blk to sane values
as Windows 10 verifies those fields starting with FADT revision 5.
Fixes: https://ticket.coreboot.org/issues/109
Tested on Windows 10.
Change-Id: Ic649040025cd09ed3e490a521439ca4e681afbbf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Family 17h redefines the PSP command and status, and therefore the
steps required to send commands via the mailbox. Convert the existing
version into a v1 and add a v2. New Kconfig options allow the soc to
choose v1 vs. v2.
The v2 PSP begins responding to the mailbox command when the full
bit range is written. Define the new mailbox as a union of a u32
and a structure.
Additional PSP details may be found in the NDA publication (#55758)
AMD Platform Security Processor BIOS Architecture Design Guide for
AMD Family 17h Processors
Change the existing two soc functions that return pointers to void
pointers.
BUG=b:153677737
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4d358fdae07da471640856f57568059e9487f6a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change disables MrcSafeConfig option during MRC training.
MrcSafeConfig was enabled as part of the early testing.
Now with FSP 2527, there is no need to set this config anymore.
BUG=b:150357377
BRANCH=master
TEST=build and boot ripto/volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I4e4069d83754aaf1e4885d6912ab2a6d506c5269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40106
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current pin-ctrl kernel v5.4 driver expects the firmware to publish
single GPIO ACPI device. Until kernel pin-ctrl driver implementation is
updated to consume community based GPIO ACPI device, update the current
ACPI code to comply with pin-ctrl driver requirement.
BUG=b:150154277
TEST=Verify intel pin-ctrl driver can successfully load in OS
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: Ifcc92adaee550182ab405541ea85019f31bb8658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
`.read_resources` and `.set_resources` are the only two device
operations that are considered mandatory. Other function pointers
can be left NULL. Having dedicated no-op implementations for the
two mandatory fields should stop the leaking of no-op pointers to
other fields.
Change-Id: I6469a7568dc24317c95e238749d878e798b0a362
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40207
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Providing an explicit no-op function pointer is only necessary for
`.read_resources` and `.set_resources`. All other device-operation
pointers are optional and can be NULL.
Change-Id: I3d139f7be86180558cabec04b8566873062e33be
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40206
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Support to configure DDR4 memory variant.
-Add support to read SPD data based on different memory topology.
-Initialize FSP UPD's for DQ and DQS mapping.
BUG=b:151702387
Signed-off-by: Varun Joshi <varun.joshi@intel.corp-partner.google.com>
Change-Id: I47a5dcad3ee316871a6103b9d53ef7f6fc88d7d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39847
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set IgdDvmt50PreAlloc to zero if InternalGfx is disabled. It's 'correct'
to do it like this, otherwise the FSP would always allocate memory for
the IGD even if it is disabled. In addition the FSP enables the graphics
panel power even if no IGD is present which leads to a crashing FSP.
Thus, if no IGD is present we switch off the panel via UPDs.
Refer to this issue on IntelFSP for details:
https://github.com/IntelFsp/FSP/issues/49
Tested on:
* CFL platform with IGD
* CFL platform without IGD
Change-Id: I6f9e0f9855224614471d8ed23bf2a9786386ddca
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
get_soc_config was a reimplementation of config_of_soc, so drop
get_soc_config and cfg_util.c.
Change-Id: I007c83cfe5063130c18819925844b6c643cf0232
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
get_soc_config was a reimplementation of config_of_soc.
Change-Id: I73c6a84703e22d6778b830f4bb82419361c85ff7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Allow the use of the common/gpio driver to create Lewisburg PCH pad
configurations for server motherboards with Skylake-SP processors.
This patch should only be applied after adding Lewisburg PCH definitions
to the soc/intel/xeon_sp code [1].
[1] https://review.coreboot.org/c/coreboot/+/39425
Change-Id: I4a8e83cad0729bbbb50ba5a2b336f6cf7c1eca13
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allow to print a debug error message when the GPIO community does not
contain the pad number from the motherboard configuration.
Change-Id: I21fb389a5d29e11b1fbc24e836d91e17957047f1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Adds definitions that allow to use the common GPIO driver to configure
the Lewisburg PCH pads. Using the GPIO configuration from common/gpio,
unlike the FSP-style definitions from Intel RefCode [1] definitions,
is more understandable and makes the motherboards code much cleaner.
In addition, we can use utilities, such as inteltool, to analyze the
configuration of proprietary firmware to add support for new server
motherboards with Skylake-SP processors.
The pin layout in this patch corresponds to the pinctrl driver in the
Linux kernel v4.14 for the Lewisburg PCH GPIO controller [2].
[1] https://designintools.intel.com/product_p/stlgrn45.htm
[2] drivers/pinctrl/intel/pinctrl-lewisburg.c
These changes are in accordance with the documentation:
[*] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US.
Change-Id: Idde32fdd53f1966e3ba6b7f5598ae8f51488d5a5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39425
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on volteer /
dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: If940a76d36a7645a7441ba418aa7aec9af9f6319
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I482715c166ccf5d2f3cc25118d25b07dbfd6650a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I3fdfa159194cccf15c0284700f554d2241dad6cd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I2efdeb224c478995d393aa3eaac762c876832391
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I1edbc8bb0efaad033385f29f8a4747bd178296b9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ib1e226e7816efbc5cffc95563b440fb2ad5b1f95
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I48422453735d50eb9292f39a3c031073d647a17c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I8995372760543e9cf2c845019f7a063046c55e9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ib41169395ab239e520f6047ac6bd307ec50776d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ic5a920bfe1059534566ceab85a97219dd56f069e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I45d746ed374361036d59167293a90d8e557754fa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I7354edb15ca9cbe181739bc2a148f16bb85ab118
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I703a656c397345025dab398fb642f3de7bbb61fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40220
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I3c6daa484a4aa133ff2ad79eb2b8efa159da3523
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I773cc57197b29fd3f4522aece4c83b3dc9e646e0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I25b9bbe320be891985e5fb42a0c3f1c763a833db
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40136
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I3d872f63d56711d39c8320ace2642cea2a23f545
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Id987662ba96ad7e78e76aa5a66a59b313e82f724
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40133
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is use to skip GT specific programming in ICL, TGL and JSL.
In following patches use of SKIP_GRAPHICS_ENABLING is removed.
b6a523927d (soc/intel/jasperlake: Remove DDI A lane programming)
e5565c45cb (soc/intel/{icelake, tigerlake}: Remove DDI A lane programming)
TEST=checked iclrvp, jslrvp and tglrvp compilation.
Change-Id: Ie337fd727d72118c43aa869da1446ea4fceadc5b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
For newer Intel graphics (>=11), the DDI port max lanes default to 4.
And kernel driver no longer relies on coreboot to provide information
via DDI_BUF_CTL_A (for DDI port A) register programming. Hence removing
this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp compilation and boot.
Change-Id: I4c171ec6a57d6fc53bee88420bfb3c0fbc5dc057
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40038
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move more Kconfig declarations to drivers/intel/fsp2_0/ and document
them properly. This way, we don't have to repeat dependencies and have
the prompts in a common place. We can also easily hide the prompt for
the header path in case the FSP repository is used.
SP platforms were skipped as their Kconfig is too weird but they
shouldn't hold other platforms back.
Change-Id: Iba5af49bcd15427e9eb9b111e6c4cc9bcb7adcae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This change updates memory configuration on Tiger Lake Platform to
replace "Reserved9" with "DisableDimmCh#" UPD in init_spd_upds().
For reference https://review.coreboot.org/c/coreboot/+/39797 added
"DisableDimmCh#" UPD.
BUG=b:152000235
BRANCH=none
TEST= build volteer and boot to kernel
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie0b5783a8bef02ec8c265fa5b47ce532a77b9675
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40061
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I7c3c75eaf2d7a64e7d833541bcf168b93921a142
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ie78224f9bedd6ec3f0f10a58bb5dceeb35b73241
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I149d06d6241f81b535f64720d61bbd0c198caeda
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I1b7a4fd5c6049230799d9e77903382812bc9768d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I22fffa0eab006be2bad4d3dd776b22ad9830faef
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Unmentioned fields are initialized with 0 (or NULL) implicitly. Beside
that, the struct has grown over the years. There are too many optional
fields to list them all.
Change-Id: Icb9e14c58153d7c14817bcde148e86e977666e4b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40126
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add minimal MP init. No SMM, no turbo, not c/p states.
TEST=boot linux kernel, observe CPUs are online, schedule tasks
and perform useful work. Tested on Cedar Island CRB with only 1
socket populated
Change-Id: I0af374ab3956009e9208917d911d29eb21db6069
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
There are boards that do not need a specific domain_vr_config because
the defaults provided by the soc code are sufficient. Currently, this
means that these boards can't benefit from lower power states (PSI 3
and 4) because the settings default to being disabled since at the time
the defaults have been defined (2015) there were bugs in FSP in this
regard.
Set the default values of psiXenable to 1 for boards that do not have a
domain_vr_config setting in their devicetree, just like Cannon Lake
does.
Boards that have a domain_vr_config and set their specific settings are
not affected at all. Currently, there are only three boards that have
no domain_vr_config:
- supermicro/x11-lga1151-series
These boards have a MPS MP2955 which we can assume support for PS3
(the MP2965 and MP2935 support it, too).
S-series CPUs with a 1151 socket do not have C9/C10 but only C8 and
since only C10 makes use of PS4, those CPUs won't ever request PS4.
That means we do not need to disable it explicitly for these boards.
- 51nb/x210:
Needs testing and/or VR datasheet check for PS3/PS4 support
Change-Id: I5b5fd9fb3b9b89e80c47f15d706e2dd62dcc0748
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39980
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add hook to generate ACPI methods in SSDT for screen backlight control.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: I0adccc6c8bee71d3c1b7840518308c8dc8ea2d81
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add hook to generate ACPI methods in SSDT for screen backlight control.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: I0b7fc45bda3aaf89306bedb579fb1e9f8ce07926
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add framework to generate ACPI methods in SSDT for
screen backlight control. Adjust params for gtt_ methods
to match prototypes in i915.h and avoid conflicts.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: If93b7690ef36b5d19ca43957e8a1bef91ec5821d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These two identifiers were always very confusing. We're not filling and
injecting generators. We are filling SSDTs and injecting into the DSDT.
So drop the `_generator` suffix. Hopefully, this also makes ACPI look a
little less scary.
Change-Id: I6f0e79632c9c855f38fe24c0186388a25990c44d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: David Guckian
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds new memory topologies (SODIMM, MIXED) that are
supported by DDR4 and macros required for DDR4 support.
Memory initialization support for DDR4 will be added in a follow-up
change.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I4b565c3d71bbf437da64ac29597cc19e58f1b98a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This change reorganizes memory initialization code for LPDDR4x on
TGL to allow sharing of code when adding support for other memory
types. In follow-up changes, support for DDR4 will be added.
1. It adds configuration for memory topology which is currently only
MEMORY_DOWN, however DDR4 requires more topologies to be
supported.
2. spd_info structure is organized to allow mixed topologies as well.
3. DQ/DQS maps are organized to reflect hardware configuration.
TEST=Verified that volteer still boots and memory initialization is
successful.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib625f2ab30a6e1362a310d9abb3f2051f85c3013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The initialization code in common//psp is very specific to Family 15h.
Move this to the stoneyridge directory.
BUG=b:130660285
TEST: Verify PSP functionality on google/grunt
Change-Id: Ice3d06d6437f59a529c26fc2359565c940d39482
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://chromium-review.googlesource.com/2020365
Reviewed-by: Eric Peers <epeers@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The commands used in Family 15h for loading the SMU FW blobs out of
flash had already been defined differently in Family 17h. To begin
removing Family 15h dependencies from the common/psp, change the
definitions of blob type to no longer match the Family 15h commands.
Consolidate the two functions used for interpreting the command and
applying the command into a single one.
BUG=b:130660285
TEST: Verify PSP functionality on google/grunt
Change-Id: Ic5a4926175d50c01b70ff9b10908c38b3cbe8f35
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://chromium-review.googlesource.com/2020364
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Tested-by: Eric Peers <epeers@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Switch to using Jasper Lake SoC code from soc/intel/jasperlake and stop
referring from soc/intel/tigerlake.
Addtionally mainboard changes are done to support build.
BUG=b:150217037
TEST=Build and boot waddledoo. Build jasperlake_rvp and volteer board.
Change-Id: I39f117bd66cb610a305bcdb8ea65332fd0ff4814
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Include types.h in src/soc/intel/common/block/include/intelblocks/cse.h
to use type bool.
Without this, there can be a build error like below,
src/soc/intel/common/block/include/intelblocks/cse.h:208:1:
error: unknown type name 'bool'; did you mean '_Bool'?
bool cse_is_hfs1_com_soft_temp_disable(void);
^~~~
_Bool
src/soc/intel/common/block/include/intelblocks/cse.h:214:1:
error: unknown type name 'bool'; did you mean '_Bool'?
bool cse_is_hfs3_fw_sku_custom(void);
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I92ee533bca7dc255f7a341b2a68bbc09900996a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
After measured boot is decoupled from verified boot in CB:35077,
vboot_platform_is_resuming() is never vboot-specific, thus it is
renamed to platform_is_resuming() and declared in bootmode.h.
Change-Id: I29b5b88af0576c34c10cfbd99659a5cdc0c75842
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
For quite a bit now we are extending the FSP_USE_REPO option to be
available for all Intel SoCs. This results in a list being not only
hard to maintain but also prone to errors.
To change that behaviour this commit introduces the
HAVE_INTEL_FSP_REPO config option for SoCs that are supported from within
3rdparty/fsp.
If a SoC selects HAVE_INTEL_FSP_REPO the config option FSP_USE_REPO is
selected by default, but can be still deselected by the user in menuconfig.
Change-Id: I68ae373ce591f06073064aa75aac32ceca8fa1cc
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37582
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For newer Intel graphics(>=11), The DDI port max lanes are set to 4 by
default. And kernel driver no longer relies on coreboot to provide
information via DDI_BUF_CTL_A(for DDI port A) register programming.
Hence removing this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp and tglrvp compilation and boot.
Change-Id: I32692501b60f48a07b8fbb9bb3a755b18f4b3ea9
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39313
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We're running into more and more situations where we need to tell one
SOC type from another, and instead of rewriting them every time, just
add some helper functions to the picasso SOC directory.
Change-Id: I24b73145cdfa80c09fbe036d1fb6079696c6d013
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051514
Reviewed-on: https://chromium-review.googlesource.com/2060904
Reviewed-on: https://chromium-review.googlesource.com/2060905
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FSP UPD TcssAuxOri is used for setting the IOM_TYPEC_SW_CONFIGURATION_3.
Configure TcssAuxOri to retimer enabled on the port 2 Type-C port.
This setting informs the SoC that a retimer is taking care of SBU
orientation therefore it does not need to do any flipping.
The IOM_TYPEC_SW_CONFIGURATION_3 is a bitfield that controls the aux
orientation settings for the Type-C ports. The TGL EDS describes this
setting and what each bit represents.
Reference section 3.6.5 in TGL EDS #575681
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on volteer,
Connecting Type-C display should work regardless of Type-C cable
orientation.
Change-Id: Iae356113cbdc72983f800060b1ebebe3c66b9daf
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39459
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pollock uses the FT5 footprint, so add the Kconfig option to
allow us to differentiate the chips.
Change-Id: Ia4663d38f1824786f14b6aa000adf27d64e70b5f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051509
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT. Hook into soc/common framework
by implementing intel_igd_get_controller_info().
Change-Id: I70e280e54d78e69a335f9a382261193c593ce430
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add framework to hook up the generic src/drivers/intel/gma ACPI
backlight control for platforms using SOC_INTEL_COMMON_BLOCK_GRAPHICS.
Add a weak function to get the struct i915_gpu_controller_info needed
to generate the SSDT, defaulting to NULL, which SoC's will override.
Each SoC will need to override intel_igd_get_controller_info, and
individual boards will need to populate the struct in order for
the backlight control methods to be added to the SSDT.
Change-Id: I993770fdcd0a28cee756df2bd6a795498f175952
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32549
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a follow-up patch to initial copy patch for Jasper Lake SoC.
Remove all Tiger Lake specfic code from Jasper Lake SoC code.
BUG=b:150217037
Change-Id: I44dc6bf55ca18a3f0c350f5c3e9fae2996958648
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39824
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a copy patch from Tiger Lake SoC code.
The only changes done on top of copy is changing below configs:
1. SOC_INTEL_TIGERLAKE -> SOC_INTEL_TIGERLAKE_COPY
2. SOC_INTEL_JASPERLAKE -> SOC_INTEL_JASPERLAKE_COPY
3. SOC_INTEL_TIGERLAKE_BASE -> SOC_INTEL_TIGERLAKE_BASE_COPY
We started with initial assumption that JSL and TGL can co-exist.
But now we see the SoC code in Tiger Lake is relying on too many
compile-time directives to make two SoCs co-exist. Some of the
differences are listed below:
-> Kconfig: Multiple Kconfig options using
if SOC_INTEL_{TIGERLAKE/JASPERLAKE}
-> GPIO: GPIO communities have their own differences.
This requires conditional checks in gpio.asl, gpio.c, gpio*.h,
pmc.h and gpio.asl
-> PCI IRQs: Set up differently for JSL and TGL
-> PCIe: Number of Root ports differ.
-> eMMC/SD: Only supported on JSL.
-> USB: Number of USB port are different for JSL and TGL.
-> Memory configuration parameters are different for JSL and TGL.
-> FSP parameters for JSL and TGL are different.
The split of JSL and TGL SoC code is planned as below:
1. Copy Tiger Lake SoC code as is, and change SoC Kconfig
to avoid conflicts with current mainboard builds.
2. Clean up TGL code out of copy patch done in step 1.
Make it JSL only code. The SoC config still kept as
SOC_INTEL_JASPERLAKE_COPY.
3. Change JSL SOC Kconfig from SOC_INTEL_JASPERLAKE_COPY to
SOC_INTEL_JASPERLAKE, dedede and jasperlake_rvp boards can
bind to SoC code from soc/intel/jasperlake. This step establishes
Jasper Lake as a separate SoC.
4. Clean up current JSL code from TGL code. This step establishes
Tiger Lake as a separate SoC.
BUG=b:150217037
Change-Id: I9c33f478a2f8ed5e2d8e7815821d13044d35d388
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This adds barebones support.
What works:
* Linux kernel boots fine
* SIRQ and PCH interupts work fine (only in IOAPIC mode)
* PCH devices are usable
What doesn't:
* MP init is not there yet, only 1 CPU is up
* SMM is not supported
* GPIO is not available
* All IIO and extended bus numbers enumeration is not yet available
* Warm reset flow is untested
* MRC cache save/load
TEST=boots into Linux
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I7c987badc3c53f16ad178369c7e0906d6596e465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39713
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use early serial output we need to enable P2SB BAR0, because
that allows PCR access to PCH registers.
TEST=tested on OCP Tioga Pass
Change-Id: I476f90b2df67b8045582f0b72dd680dea5a9a275
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Make use of the publicly-available FSP binaries and headers for Comet
Lake. Also, remove the Comet Lake header files from src/vendorcode,
since they are no longer necessary.
Change-Id: I392cc7ee3bf5aa21753efd6eab4abd643b65ff94
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39372
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
