The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In order to support no MIPI camera variant, move related configuration into variant folder.
BUG=b:188272162
BRANCH=none
TEST=build no MIPI camera variant without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4e64d078a8e39732ad29443c3b09ca008a7e902f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on schematic and gpio table of volet, update gpio and
devicetree settings for volet Proto.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia0e9557e01ce1e7a49a3dddf6da3e4a29587a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55113
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add 1 port and 1 endpoint
2. Add support for OVTI8856
WFC is on I2C0
BUG=None
BRANCH=None
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Ic5e9c28f255bdf86a68ce80a4f853be4e7c7ccfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Update the first version DPTF parameters received from the thermal team.
BUG=b:188936764
TEST=emerge-volteer coreboot chromeos-bootimage
Cq-Depend: chrome-internal:3851737
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Id14b1d0bdd48c65eafbdd2e80b4611c86781be00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling AC connect/disconnect wake events in brya to meet Chrome OS
wake requirements.
These changes are similar to Volteer and Shadowmountain.
BUG=none
BRANCH=None
TEST=manual tested DUT wakes for AC connect/disconnect in S0ix
Change-Id: I14b3efd429e3aa701af534f150baf35fcdeb9f35
Signed-off-by: madhusudanarao amara <madhusudanarao.amara@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54855
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Sooraj Govindan <sooraj.govindan@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We would like to have an easy way to completely disable TPM support on a
board. For boards that don't pre-select a TPM protocol via the
MAINBOARD_HAS_TPMx options, this is already possible with the
USER_NO_TPM option. In order to make this available for all boards, this
patch just removes the whole USER_TPMx option group and directly makes
the TPM1 and TPM2 options visible to menuconfig. The MAINBOARD_HAS_TPMx
options can still be used to select defaults and to prevent selection of
a protocol that the TPM is known to not support, but the NO_TPM option
always remains available.
Also fix some mainboards that selected TPM2 directly, which they're not
supposed to do (that's what MAINBOARD_HAS_TPM2 is for), and add a
missing dependency to TPM_CR50 so it is set correctly for a NO_TPM
scenario.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0a73da3c42fa4e8deffecb53f29ee38cbb51a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5cbc620001d3c21c538b62ab2811b6e07269feb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54962
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The firmware config field in CBI lets us control initialization
parameters based on the OEM design.
BUG=b:188713024
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I56ddc7218688919f20f41e0f143419c39d83849d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the default for the corresponding UPD of the Picasso FSP is
DXIO_PSPP_POWERSAVE and the devicetree default is DXIO_PSPP_PERFORMANCE,
add a deviectree setting for each board that's using the Picasso SoC
code to not change the setting for the existing boards.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0008ebb0c0f339ed3bdf24ab95a20aa83d5be2c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Not sure which policy we should select here or if that should be done in
the board-specific devicetree overrides instead of the baseboard.
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I792d909ce75cb73571c9fec58c18f749ea3ae029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54933
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All relevant USB phy settings can now be controlled via devicetree.
The given values are the AMD default ones.
For proper tuning procedure and values contact AMD.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ie8d08bde54f8c0cb8202ba111b9c7a9bd33fa03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Configure GPIO CAM_PDN5 (AP_XHCI_INIT_DONE) as output, so that
payloads (for example depthcharge) can assert it to notify EC to enable
USB VBUS.
BUG=b:187149602
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I3bf63f91b8057e35be2780024a8b398c3044729b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54902
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
haboki/habokay is the same design as drawlat/drawcia, and differs only
in replacing Cr50 with discrete TPM.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot
Cq-Depend: chrome-internal:3850094
Change-Id: Id866927b7041c5bf1c73fb4f0c03798eb61efa79
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54755
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new memory MT53E512M32D1NP-046 WT:B in the mem_parts_used.txt and
generate the SPD ID for the parts.
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib797af858e8f7ea275291e552102db74f4724aad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 2f8a7046bb.
Reason for revert: CB:54752 makes this unnecessary
Change-Id: I3ad0bcafe50e3eafb9a106720c6c9ea5cb0efc4f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54789
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update ACPI HID to 10025682 for Machine driver probe
BUG=b:187912480
TEST=Build and boot to OS in Mancomb. Ensure that the sound card probed.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5dc87c7a8fb876adc26165655f8f2d4157aa68c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54749
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:188446049
TEST=Build and boot to OS in mancomb. Ensure that the system can suspend
and resume successfully. Ensure that the sleep state GPIOs are
reflecting the state as expected.
Change-Id: I43e86a07075fe66f89c2c5665adc209e985e4f04
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Drawper support LTE+HDMI,
so use DB_PORTS_1A_HDMI_LTE to select HDMI VBT output for it.
BUG=b:186393848
BRANCH=dedede
TEST=Build and boot to OS check HDMI output works.
Change-Id: Ibf34cce1e3cbfce8a71dce880c50f85db9295b1e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: I9d6e606763798afc6b797d7d24ee7cae09f9e33f
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54681
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: Iefc4b5b489cb8caf59f21dd4333d7af66ba47c32
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54282
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UI monitors this input event and sends global mic mute command to CRAS
when the physical switch is toggled.
BUG=b:184593945
BRANCH=puff
TEST=build image and verify with evtest on DUT.
Apply crrev.com/c/2870806 with chrome cmdline flag and verify global
mute is triggered.
Verify sequences of switch toggle and suspend/resume.
Change-Id: Id89947885fdd96c5b5d598bda6db127daf298dc3
Signed-off-by: Ben Zhang <benzh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The time constant values were taken from the zork thermal.asl.
BUG=b:186166365
TEST=Boot guybrush to OS and verify logs look correct
thermal-0294 thermal_trips_update : Found critical threshold [3641]
thermal-0321 thermal_trips_update : No hot threshold
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal-0219 thermal_get_polling_fr: Polling frequency is 100 dS
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [TM00] (33 C)
thermal-0200 thermal_get_temperatur: Temperature is 3070 dK
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaeed75bdaa16b117d0fa7144ede98db1388f74f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Modify the value of "SPEAKER_GPIO_NAME" in katsu as rt1015p sdb
BUG=None
BRANCH=kukui
TEST=Speaker can work normally in katsu during firmware stage
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ib3672383ab34bb07b4e5eb7f7e8b4549e13c67b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54642
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct the Realtek ALC3254 codec name in the comment. The name is used
in the original commit message, and is also present in the Linux kernel
(`sound/pci/hda/patch_realtek.c`).
The file was an exact copy of
`src/mainboard/google/sarien/variants/arcada/include/variant/hda_verb.h`
added in commit 95370e1f (mb/google/sarien: Add HD Audio verb table).
Change-Id: I43cd73a14e07eb4518e3d44b6f81dff5016da721
Fixes: e3443d87 ("mb/google/drallion: Add new mainboard")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Correct the Realtek ALC3254 codec name in the comment. The name is used
in the original commit message, and is also present in the Linux kernel
(`sound/pci/hda/patch_realtek.c`).
Change-Id: Id8a099297bd8bcebf9734e1beee2449fdcca75c5
Fixes: 95370e1f ("mb/google/sarien: Add HD Audio verb table")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel. Also configure Audio Co-processor(ACP) to operate in I2S TDM mode.
BUG=b:187860242
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I528f90d81a418236e512a1e0840ff44c3a3a983e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The handler is the same on all Bay Trail mainboards. Factor it out.
Change-Id: Ia1b6faaca4792cda5f14948d23498182bf4bb2c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54415
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Máté Kukri <kukri.mate@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move discrete TPM in the devicetree to avoid emitting the following
message: "Using default TPM ACPI path: '\_SB_.PCI0.LPCB'"
There is no corresonding ACPI device for 1f.5 PCI device. Therefore,
move the discrete TPM to a device that has the corresponding ACPI
device node. Functionality should remain the same.
BUG=b:187518267
Change-Id: Ie9ec70336d5651c87f06f8b357abd1bfdb1cc06b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
In order to use the USB WWAN module in USB mode (as opposed to PCIe),
the PCIe RP must be turned off at the FSP level. The `probe` statement
in the devicetree unfortunately takes effect too late, because the UPDs
for disabling/enabling PCIE RP belong to FSP-M (romstage), whereas
fw_config probing for devicetree is done in ramstage.
Add a new variant-specific file which will handle manually setting the
UPD based on FW_CONFIG instead.
BUG=b:180166408
TEST=set CBI FW_CONFIG field to LTE_USB, see message in console,
set field to LTE_PCIE, do not see message in console.
Change-Id: Ica2f64ec99fa547e233012dc201577a14f6aa7d7
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54633
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This changes updates mainboard properties by adding DFP number, PLD
and power_gpio for each DFP.
BUG=b:186521258
TEST=Validated Retimer firmware upgrade along with upstream kernel under
no device attached scenario.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I18f29ce5f8450a8b0f8208a60b8b607f9f0d8817
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52714
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Along with upstream kernel for Retimer firmware update, coreboot defines
power control for each DFP respectively under host router. This change
removes the power_gpio from baseboard. Individual DFPx power_gpio will
be added once the dependent definition is complete.
BUG=b:186521258
TEST=Build image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Iec2437ab20d283d080752a80aa4514aa9af6897e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52711
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We recently added GPIO definition for PCIE vGPIO for Alder Lake.
We also need to disable GPIO dynamic PM for this community which is
already done for other communities as well.
BUG=b:188392183
BRANCH=None
TEST=Code compiles and Check if dynamic PM for GPIO COMM3 is also
disabled
Change-Id: I2f8645b8f4a9995e727a7623af97531c5de52892
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54383
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most boards use `device lapic 0 on` with zero written in decimal.
For the sake of consistency, update the remaining boards to follow suit.
Change-Id: I1d3b1ac107e33aae11189cdd5e719b8e48b10f08
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Enable/disable LTE function based on LTE bit of FW_CONFIG.
The LTE function settings are included GPIO settings, USB port settings and
power off sequence.
BUG=b:187797408
BRANCH=dedede
TEST=Build and test the change on cret.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib926e99aaf9df433a7cff71180ee55431d69f718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
TEST=execute `echo b > /proc/sysrq-trigger` to reboot system
Change-Id: I1a55216c0d5a00bbdb373d931bd50ebe7ca5694f
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Configure DDI-0 connector type to DP.
BUG=b:187856682
TEST=Build and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ic8af14509b0d246c5c2da6e1a48991384471e69f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
TCSS OC pins have not been correctly configured for volteer.
This patch fills the value from devicetree to correct the OC pins
mapping.
BUG=b:184660529
BRANCH=None
TEST="emerge-volteer coreboot chromeos-bootimage", flash volteer2 and
verify CpuUsb3OverCurrentPin UPDs get set correctly.
Change-Id: I12da755a1d3b9ec3ed0a2dbfb0782313dd49c7e9
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Initialize and calibrate DRAM in romstage.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.com>
Change-Id: Ib7677baef126ee60bf35da3a4eaf720eaa118a27
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
volta will use different wifi SAR from voxel.
Using clamshell mode of fw config to decide to load volta wifi sar.
BUG=b:184820057
TEST=build and verify wifi power as expect.
Cq-Depend: chrome-internal:3824093
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I000aefca63346c70556688f232ca54360b3badef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54051
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCIE6 only needed when use the PCIE LTE.
BUG=b:180166408
BRANCH=none
TEST=FM350 can/can't be detected when enable/disable this config.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9dce05fdb6eb956a054d3815ff706b94f0d3fc37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure USB HUB_RESET_L gpio to high.
BUG=b:187485847
TEST=Build and boot from USB to OS, check the USB function.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I94e4806c7463030df31f8d819510f9533a622f2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The CBFS mcache size default was eyeballed to what should be "hopefully
enough" for most users, but some recent Chrome OS devices have already
hit the limit. Since most current (and probably all future) x86 chipsets
likely have the CAR space to spare, let's just double the size default
for all supporting chipsets right now so that we hopefully won't run
into these issues again any time soon.
The CBFS_MCACHE_RW_PERCENTAGE default for CHROMEOS was set to 25 under
the assumption that Chrome OS images have historically always had a lot
more files in their RO CBFS than the RW (because l10n assets were only
in RO). Unfortunately, this has recently changed with the introduction
of updateable assets. While hopefully not that many boards will need
these, the whole idea is that you won't know whether you need them yet
at the time the RO image is frozen, and mcache layout parameters cannot
be changed in an RW update. So better to use the normal 50/50 split on
Chrome OS devices going forward so we are prepared for the eventuality
of needing RW assets again.
The RW percentage should really also be menuconfig-controllable, because
this is something the user may want to change on the fly depending on
their payload requirements. Move the option to the vboot Kconfigs
because it also kinda belongs there anyway and this makes it fit in
better in menuconfig. (I haven't made the mcache size
menuconfig-controllable because if anyone needs to increase this, they
can just override the default in the chipset Kconfig for everyone using
that chipset, under the assumption that all boards of that chipset have
the same amount of available CAR space and there's no reason not to use
up the available space. This seems more in line with how this would work
on non-x86 platforms that define this directly in their memlayout.ld.)
Also add explicit warnings to both options that they mustn't be changed
in an RW update to an older RO image.
BUG=b:187561710
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I046ae18c9db9a5d682384edde303c07e0be9d790
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable DPTF functionality for Alder Lake based brya
BRANCH=None
BUG=b:188028732
TEST=Built and tested on brya board
Change-Id: I33266c85aa30869466034ccbab04a3c7820ae2b0
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Select touchscreen(s) based on touchscreen source provisioned in SSFC of CBI (higher 32 bits of FW_CONFIG in coreboot).
The reason is to avoid to enable multiple touchscreen ICs with the same slave address.
BUG=b:186609348
TEST=build and boot to OS.
Change-Id: I087ea677a8865fc8c5b3f7c9773bd7f97924dbb3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Remove TSR2 and use DPTF parameters from internal thermal team.
BUG=b:175938681
TEST=build and boot to OS.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If0ec1ec48b8971efe87f1f8d10332a9c16352122
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
In order to support wake on WLAN events, configure the wake resource.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that WiFi power resource
is added to SSDT.
Device (\_SB.PCI0.GP20.WF00)
{
Name (_UID, 0x38B82CBC) // _UID: Unique ID
Name (_DDN, "WIFI Device") // _DDN: DOS Device Name
Name (_ADR, 0x0000000000000000) // _ADR: Address
}
Scope (\_SB.PCI0.GP20.WF00)
{
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x08,
0x03
})
}
Change-Id: Ic238d9606aea20c058e9b47093693f10b14e6288
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The 448KB size of the GBB is larger than is needed, so adjust it down
to the minimum size needed.
BUG=b:186761897
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7a24945cd9ecc8872871f57b09ca71fc40e92473
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add audio codec module RT5682 in project and define GPIO_137 in the
override_table for SSFC framework to adjust IRQ configuration.
BUG=b:182221327
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682I or DA7219 then check whether device tree is updated correspondingly by disabling unselected one.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I202f71f57ad2db84fb90b52f9ffd7a1fd05494a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Create the chronicler variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:187318819
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_CHRONICLER
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Iebfea87b7c4cfc2a83e88a6c479a0842774ae018
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Probe the fw_config for RT1015 speaker amplifier operation mode and
enable it accordingly in the device tree.
BUG=b:180570923
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Change-Id: I756bfa6f604ed320de9a515821979aa95c869ebf
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add support for GPIO and SPD driver for pirika
BUG=b:184157747
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: Id367a83b04aad62b7deabae99b3f91905a2fc46c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Update LTE USB port configuration at run-time after probing the firmware
config. By default the concerned USB port takes the Type-A port
configuration.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight
Change-Id: I5ad5a1670adef54075923cf912fb41a1ce776155
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
This callback is required to update the devicetree config at run-time
after probing the firmware config.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight.
Change-Id: I857211bfc4beb36ab225f3786c1707336a34aae9
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Enable Display Controller Engine Audio endpoint to enable HDMI audio.
BUG=b:186479763
TEST=Build and boot to OS in guybrush.
Change-Id: I5e35440e8e70ee125d37c7ac30c9219ec69c7c6e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Everybody wants a stylish stylus. Enable the power system to it.
BUG=b:186267293
TEST=connect multimeter to PP5000_PEN and see it go from 0 to 1. MAGIC!
Signed-off-by: Eric Peers <epeers@google.com>
Change-Id: I11d05c118ec9451d26136c320f3650c489e02c59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Both mt8192 and mt8195 use MT659P RTC. Move mt8192/rtc.c to common
folder and rename to rtc_mt6359p.c.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I73ea90512228a659657f2019249e7142c673e68e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53897
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PIC IRQs are required so we can correctly set up the PCI_INT
registers. This only matters when booting in PIC mode. We don't need to
set the IO-APIC registers since the linux kernel will auto-assign those
to reduce conflicts.
BUG=b:184766519
TEST=Boot guybrush with `pci=nomsi,noacpi amd_iommu=off noapic` and
verify xhci and graphics continue to work.
$ cat /proc/interrupts
12: 285064 XT-PIC nvme0q0, nvme0q1, rtw88_pci
13: 100000 XT-PIC xhci-hcd:usb1
14: 4032 XT-PIC amdgpu, xhci-hcd:usb3
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d66ccd08a86a64242dbc909c57ff9685828f61f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52915
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mcache is overflowed in the latest build. In order
to fix the mcache overflow, we increase the mcache size
to 0x4000 and adjust the percentage to 50% for the ro/rw
mcache. This change is for all of the volteer variants
as we see many of the volteer variants which use the
latest bios having the mcache overflow issue.
BUG=b:187095474, b:187095765, b:187234881, b:162052593
TEST=no mcache overflow in the bios log
Change-Id: If9552bc9fa5d36b1ca662c9da030ae7b137b60a8
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add backlight support in sn65dsi86bridge through the AUX channel using
eDP DPCD registers, which is needed on the GOOGLE_HOMESTAR board.
Change-Id: Ie700080f1feabe2d3397c38088a64cff27bfbe55
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52663
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace `3` with `SaGv_Enabled`, which has the same value.
Change-Id: I05cfddfefc45ba5bfb0e684445a6d8e02d7865e3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Create the volet variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:186334008
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLET
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ic6ca9a78494e3819b0fb39c0bcc70fed95c2c589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Add SPD support to elemi for K4AAG165WB-BCWE
BUG=b:187379245
TEST=FW_NAME=elemi emerge-volteer coreboot chromeos-wqbootimage
Change-Id: I839447a9e7c7b6558b2d0877c67dc9cf89ee792a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Mancomb uses DDR4 SODIMMs, but the default cezanne configuration is for
the LPDDR4 version. This changes to use SODIMMS.
Further changes may be needed for platform customization, so I put the
config file in variants/baseboard instead of the root mancomb directory.
BUG=b:187094481
TEST=Build only
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icc4dc8aec2053cb177765f57e57cac7a099508fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
DISABLE_KEYBOARD_RESET_PIN - This pin goes to a test point and is not
used for the reset.
DRIVERS_UART_ACPI - Add the UART ACPI code
FW_CONFIG - Mancomb uses the firmware config interface
PSP_DISABLE_POSTCODES - The PSP is not yet initializing eSPI correctly
to send post codes to the EC, so disable them for now.
BUG=None
Test=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I39efcc8d1e0fb1e7ac0b0541a49db0ac0ee56481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
This same patch was added for Guybrush at CB:52673
BUG=b:186045622, b:181139095
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac86d2ef5bdd21fbb0a0d4e235efe4fe621023b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52948
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:186380809
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I0975a8b64452c3f636e6c5937c6918518ec5b4e9
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
TGL boards using the Type-C subsystem for USB Type-C ports without a
retimer attached may require a DC bias on the aux lines for certain
modes to work. This patch adds native coreboot support for programming
the IOM to handle this DC bias via a simple devicetree
setting. Previously a UPD was required to tell the FSP which GPIOs were
used for the pullup and pulldown biases, but the API for this UPD was
effectively undocumented.
BUG=b:174116646
TEST=Verified on volteer2 that a Type-C flash drive is enumerated
succesfully on all ports. Verified all major power flows (boot, reboot,
powerdown and S0ix/suspend) still work as expected.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I70e36a41e760f4a435511c147cc5744a77dbccc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pen Detect GPIO is exported through GPIO keys driver to the kernel so
that stylus tools is popped on pen eject event. Hence enable the GPIO
keys driver and configure the devicetree.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that PRP0001 device is
added to the ACPI SSDT table. Ensure that the Pen Eject events are
detected.
Event: time 1620159356.243180, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1620159356.243180, -------------- SYN_REPORT ------------
Event: time 1620159356.735316, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Ensure that when the device is suspended, it wake on Pen Eject event and
does not wake on Pen Insert event.
Change-Id: I4d2aa29c0f1839c563b40734527a687a5618ba5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=Wake system from S0i3 with EC and see GPE 3 increment.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If7f9d2c13503c01fb9d834c436dac723f2c3b24c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Now the bootblock is not limited to 64K so integrating vboot into the
bootblock reduces the binary size.
Change-Id: Ic92ecf8068f327a893d20924685ce571752d379f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52787
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure GPP_A20 as PAD_CFG_GPI_IRQ_WAKE to enable interrupt and wake routes for touchscreen device.
BUG=b:186070097
BRANCH=puff
TEST=Build and make sure TS works to wakeup suspend/resume.
Change-Id: I2bbaab56924849a22a4d05ce53bf5bdcf00265dd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Disable HDMI 2.0 for Vilboz and then support display resolution 4K 30Hz
BUG=b:179170193
BRANCH=firmware-zork-13434.B
TEST=verified that the resolution of the display is 4K 30Hz
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ib0dc0d584f0e87bc9c3da85a583cb8c8bed76440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib956fc299fe21cd7ea0b465cbdc5c8da830a668d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Default VBT supports only integrated Display port. Magister supports a
HDMI port and hence support a separate VBT for Magister.
BUG=b:180666608
BRANCH=dedede
TEST=Build and boot to OS.
Cq-Depend: chrome-internal:3661227
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I52c10452887312959f68cfc4e25d5897dae388f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51279
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mancomb will have the boot flash on a daughterboard, so the SPI speeds
need to be low for now.
BUG=b:182211161
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Icacb68d65fb414197d7b8d45799527d8d2568dc7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Guybrush is pretty definitely alive, so this can be removed, as the
TODO line said.
BUG=180721202
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I14f89f3e6f780c2da2136a838950ef2bcebc4c3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
There is no lid switch in mancomb so remove it.
Will replace the lid switch with a fake gpio in depthcharge.
BUG=b:182211161
TEST=Depthcharge no longer halts complaining that coreboot didn't sample
the pin
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ifd0fcec9557bf7ebad64ce9342d3b50eb511522b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The usage of external oscillator has got nothing to do with Audio
Co-processor (ACP). Hence move it out of common config and put it into
the SoC config where it is being used.
BUG=None
TEST=Build Dalboz and Vilboz mainboards.
Change-Id: I8c5d98addfba750f9ddb87a846599541b4a8340a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Follow the FP6 IRM(#56328) to set the stapm parameter
and allow other mancomb variants boards can customize those parameters.
BUG=b:1181157669
TEST=build.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ib3ed76e5212a5a8b5fb4fcc3d6884ceff82377b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The boolean is stored in ChromeOS NVS, not GNVS.
Change-Id: I5c424a052d484228a456f8f0ad4fb0bed3165e09
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Brya uses CBI to store dram part number. So enable the config.
BUG=b:186571840
BRANCH=none
TEST=dmidecode -t 17 can show the dram part number.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1b4fc4da31d8964763c3e671d84be71996fa5e2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
According to SED team provided ELAN touch screen SPEC. IRQ trigger
method need set with level trigger, that modify IRQ trigger to level
from edge.
BUG=b:174972088
TEST=Build FW and boot to OS and check with test result.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I9237d9aad6166a5754afe464ce8453129a58d283
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
guybrush and mancomb don't configure any GPIO as PAD_SMI. Since
mainboard_smi_gpi will only get called for a GEVENT that will cause a
non-SCI SMI, this isn't expected to be called. For the unexpected and
very unlikely case that it still does get called, put a printk into
mainboard_smi_gpi to see what is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd6e3348ecc078932bf6cf5b0830b4b034d274bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52360
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
zork doesn't configure any GPIO as PAD_SMI. Since mainboard_smi_gpi will
only get called for a GEVENT that will cause a non-SCI SMI, this isn't
expected to be called. For the unexpected and very unlikely case that it
still does get called, put a printk into mainboard_smi_gpi to see what
is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14c67b21a83b334558cdd54ebf700924aa9d0808
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52359
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure Audio Co-processor(ACP) to operate in I2S TDM mode. Also fix
the scope in which ACP is defined in the devicetree.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Change-Id: Ic90fd82e5c34a9feb9a80c4538a45e7c2fb91add
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Audio Co-processor driver is similar for both Picasso and Cezanne SoCs.
Hence move it to the common location.
BUG=None.
TEST=Builds Dalboz, Trembyle, Vilboz, Mandolin and Bilby mainboards.
Change-Id: I91470ff68d1c183df9a2927d71b03371b535186a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
All guybrush boards should have system_configuration set to 2, so
put this in the main devicetree.
BUG=b:185209734
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I1ce2acb3b4ed51aa9a0aa379ed125f0b04f04d31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
From ANX7625 spec, the delay between powering on power supplies and GPIO
should be larger than 10ms. Since it takes about 4ms for the previous
GPIO EN_PP3300_EDP_DX to be pulled up, increase the delay from 2ms to
14ms.
BUG=b:157716104
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: If73747bdaec5ac069b048920d27e27178bc3cedc
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Follow L850GL spec to adjust power sequence. RST need to drive low
before power on then drive to high.
SPEC:FIBOCOM_L850-GL Hardware User Manual_V1.0.8
BUG=b:186374631
TEST=WWAN is detected by lsusb.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I13357677bb1ab185abf1d4c915a762a9d6894312
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This changes adds the EC_HOST_EVENT_USB_MUX to be dark resume source.
BUG=b:183140386
TEST=In S0ix, remove DP dongle, system does dark resume. AP and EC
synchronized. AP got port partner disconnection.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I53bd4fee21e2e2d1f16f558ab0341a50ef9a0e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52716
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Reviewed-by: Abe Levkoy <alevkoy@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Define TOUCH_RPT_EN pin(GPP_A11) as the stop_gpio for the touch screen
and control TOUCH_RPT_EN pin to keep low.
BUG=b:176253069
TEST=Build and boot metaknight to OS, confirm GPP_A11 pin keep low.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I816e29eccac0f1935aeaa3b94c907870e2451e3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52653
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Brya uses CNVi WiFi module, PCIE setting is not required.
TEST=WiFi is functional in the OS.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib82c98905ed3b30075e9830c1a2638817f140abe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
BUG=b:186045622, b:181139095
TEST=`lpc sci` on EC console and see /proc/interrupts increase by 1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I764b9ec202376d5124331a320767cbf79371dc07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Roll back CPU slow slew rate setting to Intel default "SLEW_FAST_2"
Because baseboard modify slow slew rate setting to "SLEW_FASE_8"
for all project, but Lindar and Lillipup is using "SLEW_FAST_2",
so this setting need to roll back.
BUG=b:186140230
TEST=Build FW and boot to OS checking with CPU log.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I7de252b26c75f8dad218f3eb79a0988e60964f4c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52620
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5e3e9fe21f44b832e26b0942759ae2ec96ec6c82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add dynamic fan table mechanism for Lindar and Lillipup.
Create different fan tables that provided from thermal team.
BUG=b:185308432
TEST=Build FW and boot to OS modify CBI test with DPTF tool.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I1b79dbe1ae6ee7aa41cef832b4ee305cc8f4b753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
BUG=b:185939089
TEST=Build and boot to OS in Guybrush. Enter S0i3 after passing the
sleep state configuration from the mainboard.
Change-Id: I4b23b014ca45bd09c76b626b73b0332586dec056
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Enable GL9755 SD card reader.
BUG=b:185397257
TEST=SD card is functional in the OS.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib3be54274ca796bedda76ce807a0bd630d1d8e4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently, it fails to dump the nvme data by test command.
It reports the following error:
cat: '/sys/bus/i2c/devices/i2c-PRP0001:01/eeprom': Connection timed out
So increase the value from 0x0400 to 0x2000 and double the address width from 0x08 to 0x10 to solve this problem.
BUG=b:177393430
TEST=1. cat /sys/bus/i2c/devices/i2c-PRP0001:01/eeprom > /tmp/ov8856_eeprom.bin
2. hexdump -C /tmp/ov8856_eeprom.bin > ov8856_eeprom_dump.log
3. cat ov8856_eeprom_dump.log
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ia933927981f07e0f7954a4bc6d82f0bdd70181f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52048
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: ShawnX Tu <shawnx.tu@intel.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The next guybrush build uses 2 new LPDDR4X memory chips:
- Micro MT53E1G32D2NP-046 WT:B
- Hynix H9HCNNNBKMMLXR-NEE
The MT53E2G32D4NQ-046 WT:A chip has been added to the global LPDDR4X
list since the last time guybrush was updated, so that's brought into
the guybrush SPD directory as lp4x-spd-10.hex, but it's not used.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ia5efd548f8b9442fb3703518387175aba8933a33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add cs42l42 codec support in fleex.
BUG=b:184103445
TEST=boot to check cs42l42 is functional.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1571003f8b272a573e6ab9fb525f17659bae8c4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch includes changes to enable display and DSP audio UPD.
BUG=b:181219097,b:183482000
TEST=Audio sound card is detected and listed by the linux kernel.
Audio playback and capture is working on the Brya.
Change-Id: I3dab02bedb6df995b1efd27332d3aa26985e188e
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch has changes to support multiple cameras modules, based on
the value set in the SSFC_CONFIG.
BUG=b:176065425
TEST=Tested the changes with magolor 5MP and 8MP camera.
Change-Id: I764abf70bacbe61452e7b0fd59c1b375227b5748
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add PSP_DISABLE_POSTCODES and PSP_POSTCODES_ON_ESPI kconfig options for
cezanne. Select PSP_DISABLE_DISABLE_POSTCODES and unselect
PSP_POSTCODES_ON_ESPI for guybrush. Port80 codes from PSP can cause bus
errors on guybrush.
BUG=b:185514903, b:184356693
TEST=Boot guybrush, observe no port80 codes from PSP
Change-Id: I7241e47ec1b89782e699135370c796eb251afcaa
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52401
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All related mainboards are setting DIMM_SPD_SIZE to 512. Therefore,
default to 512 in the SoC Kconfig and drop it from related mainboard
Kconfigs.
Change-Id: Idb6a0e42961eeb490afd76b4aa7d940961991733
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52513
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the DPTF parameters. Modify TDP, Critical Policy and Active Policy setting.
BUG=b:177777472
BRANCH=firmware-volteer-13672.B
TEST=build test firmware and verified by thermal team.
Change-Id: Ib57de5535f3d37765ac7051c17445c311c098927
Signed-off-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ariel Chang <ariel_chang@pegatron.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Replace CONFIG(CHROMEOS) with CONFIG(CHROMEOS_NVS) for cases where
the conditional and dependency are clearly about the presence of
an ACPI NVS table specified by vendorcode. For couple locations also
CONFIG(HAVE_ACPI_TABLES) changes to CONFIG(CHROMEOS_NVS).
This also helps find some of the CONFIG(CHROMEOS) cases that might
be more FMAP and VPD related and not about ChromeOS per-se, as
suggested by followup works.
Change-Id: Ife888ae43093949bb2d3e397565033037396f434
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the measurement, adjust the delay time between the main power rail and reset signal to 7ms in order to match the spec. of touch controller, eKTH7918U.
BUG=b:184126265
BRANCH=firmware-volteer-13672.B
TEST=build test firmware and verified by EE team.
Change-Id: Iea84046c1b1f3fe6ab8bb89d86d00b1e89325f71
Signed-off-by: Hao Chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add control charging current from TSR0 and correct charger_perf table value.
BUG=b:179067801
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Ie0d969898defe76952e5c136fa93b7edffe51de3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Edward Doan <edoan@google.com>
Condition use of RO_VPD for LAN MAC address on CONFIG_VPD rather
than CONFIG_CHROMEOS.
Test: build/boot google/{beltino,jecht} with RO_VPD propagated from
stock firmware, verify MAC address set correctly.
Change-Id: I1606fe1936ccee6e03dee145901767c8e73bfe2d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52517
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Metaknight has two daughter-board (DB_PORTS_1A_HDMI and
DB_PORTS_LTE_HDMI), LTE and USB Type A use the same usb port,so needs to
probe daughter-board to avoid USB device cannot recognize correctly.
BUG=b:184809456
TEST=build and verify USB device can recognize correctly
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie42d12c7ce5c7341751c3cf92b5f37b6cd4d479f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Kaiyen Chang <kaiyen.chang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 1e36dc078e. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Change-Id: I921dc5c814e5187dce283eeff43075b59885723a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52418
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Ensure the ChromeOS FMAPs are used only when CONFIG_CHROMEOS
is selected, so non-ChromeOS targets use the default x86 FMAP.
Change-Id: Id5d3e7a44973f2fadba3ea15e0e544eee7fa53e6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
EN_SPKR is routed to SD pin in the ALC1019 speaker amplifier. The
concerned pin has a voltage rating of 1.8V whereas the EN_SPKR GPIO has
a voltage rating of 3.3 V. The schematics has been updated to bridge the
gap. So enable the speaker amplifier by default and add a gpio override
table to disable the speakers before board version 2.
Also update the codec ACPI HID name for the kernel machine driver to
probe the codec successfully.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the GPIO output state
is high.
Change-Id: I32b29bfae9bc94b5119b33a535d8bc825ef89445
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52355
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the ACPI objects for
machine driver is populated.
Change-Id: I8ed474d25273082d1e0742ba93746d97930deb19
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI code to enable the backlight when we enter the OS.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3e0a6c06120ac5abf0a0d82494e03d9cf80c1f8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52113
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both touchpads supported by zork use level-triggered wakeup signal.
BRANCH=zork
BUG=b:172846122,b:182911201
TEST=1. cros build-ap -b zork
2. both Synaptics and ELAN touchpads work fine on Vilboz
3. Wakeup source is correctly reported on Vilboz
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: Icc2b5ad3bd434c9759a0fdfc121aa3c94f46630e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52367
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the datasheet provided by ELAN, the /INT pin is "low active"
and "indicates touchpad likes to send data to system(host) when low".
The signal is level-triggered.
BRANCH=zork
BUG=b:172846122
TEST=cros build-ap -b zork
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I1f2182aaf483932304591ab14592f35214ea6efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52366
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add uart controller to chipset.cb and leave it off by default.
Turn uart0 on for console for mainboards.
BUG=none
TEST=builds and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Iaeb7fea4b92bd89331c7ae7c1c000f8d9961fe9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
TCSS OC pins has not been correctly configured for brya.
This patch fills the value from devicetree to correct the OC pins
mapping
BUG=b:184653645
BRANCH=None
TEST=check if UPD value has been reflected correctly
Change-Id: Ia21cdbf5768ad7516ea52bff7e247291a7d2ebd1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add log to show the codec has been disabled.
BUG=b:185193926
TEST=cbmem -c | grep disabled, can find the codec name
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8ce7e435ce73beb2a5cbf5883905554227b1989b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
This is the same as zork.
BUG=b:184126844
TEST=Boot guybrush in developer mode and switch to normal mode.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib11c255ab7e937de334ecd18dc030006f7724275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
platform_descriptors.h is unrelated to the contents of baseboard/gpio.h
where it was included, so move the includes to the files where it is
actually needed.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94e59b5aac2df834d956106ac953eebfc5cf6921
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52357
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The board's ec.h file defined EC_SCI_GPI as GEVENT_24, so use that
definition in all places in the mainboard code instead of a mix of the
board specific define and the SoC's GEVENT number define.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46525ed24e9993acd3d850959dd63761a690d5df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Enable CRFP power control in gpio table. RST needs to drive low
before PWR enable. Since reset signal is asserted in bootblock,
it results in FPMCU not working after a S3 resume. This is a known issue.
BUG=b:181377402
BRANCH=None
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8a8fae80c3cc186e0a097ab2007abb656f382cbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:175364713,b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I9cf4d51f42fe250340bcb642db07796c9a480c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52312
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I102c1c5f8215a6c5f7a4451f5731167c32e27c90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52313
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
