Add SPD support to elemi for K4AAG165WB-BCWE
BUG=b:187379245
TEST=FW_NAME=elemi emerge-volteer coreboot chromeos-wqbootimage
Change-Id: I839447a9e7c7b6558b2d0877c67dc9cf89ee792a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Mancomb uses DDR4 SODIMMs, but the default cezanne configuration is for
the LPDDR4 version. This changes to use SODIMMS.
Further changes may be needed for platform customization, so I put the
config file in variants/baseboard instead of the root mancomb directory.
BUG=b:187094481
TEST=Build only
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icc4dc8aec2053cb177765f57e57cac7a099508fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
DISABLE_KEYBOARD_RESET_PIN - This pin goes to a test point and is not
used for the reset.
DRIVERS_UART_ACPI - Add the UART ACPI code
FW_CONFIG - Mancomb uses the firmware config interface
PSP_DISABLE_POSTCODES - The PSP is not yet initializing eSPI correctly
to send post codes to the EC, so disable them for now.
BUG=None
Test=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I39efcc8d1e0fb1e7ac0b0541a49db0ac0ee56481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
This same patch was added for Guybrush at CB:52673
BUG=b:186045622, b:181139095
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac86d2ef5bdd21fbb0a0d4e235efe4fe621023b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52948
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:186380809
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I0975a8b64452c3f636e6c5937c6918518ec5b4e9
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
TGL boards using the Type-C subsystem for USB Type-C ports without a
retimer attached may require a DC bias on the aux lines for certain
modes to work. This patch adds native coreboot support for programming
the IOM to handle this DC bias via a simple devicetree
setting. Previously a UPD was required to tell the FSP which GPIOs were
used for the pullup and pulldown biases, but the API for this UPD was
effectively undocumented.
BUG=b:174116646
TEST=Verified on volteer2 that a Type-C flash drive is enumerated
succesfully on all ports. Verified all major power flows (boot, reboot,
powerdown and S0ix/suspend) still work as expected.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I70e36a41e760f4a435511c147cc5744a77dbccc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pen Detect GPIO is exported through GPIO keys driver to the kernel so
that stylus tools is popped on pen eject event. Hence enable the GPIO
keys driver and configure the devicetree.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that PRP0001 device is
added to the ACPI SSDT table. Ensure that the Pen Eject events are
detected.
Event: time 1620159356.243180, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1620159356.243180, -------------- SYN_REPORT ------------
Event: time 1620159356.735316, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Ensure that when the device is suspended, it wake on Pen Eject event and
does not wake on Pen Insert event.
Change-Id: I4d2aa29c0f1839c563b40734527a687a5618ba5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=Wake system from S0i3 with EC and see GPE 3 increment.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If7f9d2c13503c01fb9d834c436dac723f2c3b24c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Now the bootblock is not limited to 64K so integrating vboot into the
bootblock reduces the binary size.
Change-Id: Ic92ecf8068f327a893d20924685ce571752d379f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52787
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure GPP_A20 as PAD_CFG_GPI_IRQ_WAKE to enable interrupt and wake routes for touchscreen device.
BUG=b:186070097
BRANCH=puff
TEST=Build and make sure TS works to wakeup suspend/resume.
Change-Id: I2bbaab56924849a22a4d05ce53bf5bdcf00265dd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Disable HDMI 2.0 for Vilboz and then support display resolution 4K 30Hz
BUG=b:179170193
BRANCH=firmware-zork-13434.B
TEST=verified that the resolution of the display is 4K 30Hz
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ib0dc0d584f0e87bc9c3da85a583cb8c8bed76440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib956fc299fe21cd7ea0b465cbdc5c8da830a668d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Default VBT supports only integrated Display port. Magister supports a
HDMI port and hence support a separate VBT for Magister.
BUG=b:180666608
BRANCH=dedede
TEST=Build and boot to OS.
Cq-Depend: chrome-internal:3661227
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I52c10452887312959f68cfc4e25d5897dae388f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51279
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mancomb will have the boot flash on a daughterboard, so the SPI speeds
need to be low for now.
BUG=b:182211161
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Icacb68d65fb414197d7b8d45799527d8d2568dc7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Guybrush is pretty definitely alive, so this can be removed, as the
TODO line said.
BUG=180721202
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I14f89f3e6f780c2da2136a838950ef2bcebc4c3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
There is no lid switch in mancomb so remove it.
Will replace the lid switch with a fake gpio in depthcharge.
BUG=b:182211161
TEST=Depthcharge no longer halts complaining that coreboot didn't sample
the pin
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ifd0fcec9557bf7ebad64ce9342d3b50eb511522b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The usage of external oscillator has got nothing to do with Audio
Co-processor (ACP). Hence move it out of common config and put it into
the SoC config where it is being used.
BUG=None
TEST=Build Dalboz and Vilboz mainboards.
Change-Id: I8c5d98addfba750f9ddb87a846599541b4a8340a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Follow the FP6 IRM(#56328) to set the stapm parameter
and allow other mancomb variants boards can customize those parameters.
BUG=b:1181157669
TEST=build.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ib3ed76e5212a5a8b5fb4fcc3d6884ceff82377b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The boolean is stored in ChromeOS NVS, not GNVS.
Change-Id: I5c424a052d484228a456f8f0ad4fb0bed3165e09
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Brya uses CBI to store dram part number. So enable the config.
BUG=b:186571840
BRANCH=none
TEST=dmidecode -t 17 can show the dram part number.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1b4fc4da31d8964763c3e671d84be71996fa5e2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
According to SED team provided ELAN touch screen SPEC. IRQ trigger
method need set with level trigger, that modify IRQ trigger to level
from edge.
BUG=b:174972088
TEST=Build FW and boot to OS and check with test result.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I9237d9aad6166a5754afe464ce8453129a58d283
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
guybrush and mancomb don't configure any GPIO as PAD_SMI. Since
mainboard_smi_gpi will only get called for a GEVENT that will cause a
non-SCI SMI, this isn't expected to be called. For the unexpected and
very unlikely case that it still does get called, put a printk into
mainboard_smi_gpi to see what is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd6e3348ecc078932bf6cf5b0830b4b034d274bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52360
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
zork doesn't configure any GPIO as PAD_SMI. Since mainboard_smi_gpi will
only get called for a GEVENT that will cause a non-SCI SMI, this isn't
expected to be called. For the unexpected and very unlikely case that it
still does get called, put a printk into mainboard_smi_gpi to see what
is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14c67b21a83b334558cdd54ebf700924aa9d0808
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52359
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure Audio Co-processor(ACP) to operate in I2S TDM mode. Also fix
the scope in which ACP is defined in the devicetree.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Change-Id: Ic90fd82e5c34a9feb9a80c4538a45e7c2fb91add
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Audio Co-processor driver is similar for both Picasso and Cezanne SoCs.
Hence move it to the common location.
BUG=None.
TEST=Builds Dalboz, Trembyle, Vilboz, Mandolin and Bilby mainboards.
Change-Id: I91470ff68d1c183df9a2927d71b03371b535186a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
All guybrush boards should have system_configuration set to 2, so
put this in the main devicetree.
BUG=b:185209734
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I1ce2acb3b4ed51aa9a0aa379ed125f0b04f04d31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
From ANX7625 spec, the delay between powering on power supplies and GPIO
should be larger than 10ms. Since it takes about 4ms for the previous
GPIO EN_PP3300_EDP_DX to be pulled up, increase the delay from 2ms to
14ms.
BUG=b:157716104
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: If73747bdaec5ac069b048920d27e27178bc3cedc
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Follow L850GL spec to adjust power sequence. RST need to drive low
before power on then drive to high.
SPEC:FIBOCOM_L850-GL Hardware User Manual_V1.0.8
BUG=b:186374631
TEST=WWAN is detected by lsusb.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I13357677bb1ab185abf1d4c915a762a9d6894312
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This changes adds the EC_HOST_EVENT_USB_MUX to be dark resume source.
BUG=b:183140386
TEST=In S0ix, remove DP dongle, system does dark resume. AP and EC
synchronized. AP got port partner disconnection.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I53bd4fee21e2e2d1f16f558ab0341a50ef9a0e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52716
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Reviewed-by: Abe Levkoy <alevkoy@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Define TOUCH_RPT_EN pin(GPP_A11) as the stop_gpio for the touch screen
and control TOUCH_RPT_EN pin to keep low.
BUG=b:176253069
TEST=Build and boot metaknight to OS, confirm GPP_A11 pin keep low.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I816e29eccac0f1935aeaa3b94c907870e2451e3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52653
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Brya uses CNVi WiFi module, PCIE setting is not required.
TEST=WiFi is functional in the OS.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib82c98905ed3b30075e9830c1a2638817f140abe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
BUG=b:186045622, b:181139095
TEST=`lpc sci` on EC console and see /proc/interrupts increase by 1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I764b9ec202376d5124331a320767cbf79371dc07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Roll back CPU slow slew rate setting to Intel default "SLEW_FAST_2"
Because baseboard modify slow slew rate setting to "SLEW_FASE_8"
for all project, but Lindar and Lillipup is using "SLEW_FAST_2",
so this setting need to roll back.
BUG=b:186140230
TEST=Build FW and boot to OS checking with CPU log.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I7de252b26c75f8dad218f3eb79a0988e60964f4c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52620
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5e3e9fe21f44b832e26b0942759ae2ec96ec6c82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add dynamic fan table mechanism for Lindar and Lillipup.
Create different fan tables that provided from thermal team.
BUG=b:185308432
TEST=Build FW and boot to OS modify CBI test with DPTF tool.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I1b79dbe1ae6ee7aa41cef832b4ee305cc8f4b753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
BUG=b:185939089
TEST=Build and boot to OS in Guybrush. Enter S0i3 after passing the
sleep state configuration from the mainboard.
Change-Id: I4b23b014ca45bd09c76b626b73b0332586dec056
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Enable GL9755 SD card reader.
BUG=b:185397257
TEST=SD card is functional in the OS.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib3be54274ca796bedda76ce807a0bd630d1d8e4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently, it fails to dump the nvme data by test command.
It reports the following error:
cat: '/sys/bus/i2c/devices/i2c-PRP0001:01/eeprom': Connection timed out
So increase the value from 0x0400 to 0x2000 and double the address width from 0x08 to 0x10 to solve this problem.
BUG=b:177393430
TEST=1. cat /sys/bus/i2c/devices/i2c-PRP0001:01/eeprom > /tmp/ov8856_eeprom.bin
2. hexdump -C /tmp/ov8856_eeprom.bin > ov8856_eeprom_dump.log
3. cat ov8856_eeprom_dump.log
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ia933927981f07e0f7954a4bc6d82f0bdd70181f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52048
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: ShawnX Tu <shawnx.tu@intel.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The next guybrush build uses 2 new LPDDR4X memory chips:
- Micro MT53E1G32D2NP-046 WT:B
- Hynix H9HCNNNBKMMLXR-NEE
The MT53E2G32D4NQ-046 WT:A chip has been added to the global LPDDR4X
list since the last time guybrush was updated, so that's brought into
the guybrush SPD directory as lp4x-spd-10.hex, but it's not used.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ia5efd548f8b9442fb3703518387175aba8933a33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add cs42l42 codec support in fleex.
BUG=b:184103445
TEST=boot to check cs42l42 is functional.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1571003f8b272a573e6ab9fb525f17659bae8c4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch includes changes to enable display and DSP audio UPD.
BUG=b:181219097,b:183482000
TEST=Audio sound card is detected and listed by the linux kernel.
Audio playback and capture is working on the Brya.
Change-Id: I3dab02bedb6df995b1efd27332d3aa26985e188e
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch has changes to support multiple cameras modules, based on
the value set in the SSFC_CONFIG.
BUG=b:176065425
TEST=Tested the changes with magolor 5MP and 8MP camera.
Change-Id: I764abf70bacbe61452e7b0fd59c1b375227b5748
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add PSP_DISABLE_POSTCODES and PSP_POSTCODES_ON_ESPI kconfig options for
cezanne. Select PSP_DISABLE_DISABLE_POSTCODES and unselect
PSP_POSTCODES_ON_ESPI for guybrush. Port80 codes from PSP can cause bus
errors on guybrush.
BUG=b:185514903, b:184356693
TEST=Boot guybrush, observe no port80 codes from PSP
Change-Id: I7241e47ec1b89782e699135370c796eb251afcaa
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52401
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All related mainboards are setting DIMM_SPD_SIZE to 512. Therefore,
default to 512 in the SoC Kconfig and drop it from related mainboard
Kconfigs.
Change-Id: Idb6a0e42961eeb490afd76b4aa7d940961991733
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52513
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the DPTF parameters. Modify TDP, Critical Policy and Active Policy setting.
BUG=b:177777472
BRANCH=firmware-volteer-13672.B
TEST=build test firmware and verified by thermal team.
Change-Id: Ib57de5535f3d37765ac7051c17445c311c098927
Signed-off-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ariel Chang <ariel_chang@pegatron.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Replace CONFIG(CHROMEOS) with CONFIG(CHROMEOS_NVS) for cases where
the conditional and dependency are clearly about the presence of
an ACPI NVS table specified by vendorcode. For couple locations also
CONFIG(HAVE_ACPI_TABLES) changes to CONFIG(CHROMEOS_NVS).
This also helps find some of the CONFIG(CHROMEOS) cases that might
be more FMAP and VPD related and not about ChromeOS per-se, as
suggested by followup works.
Change-Id: Ife888ae43093949bb2d3e397565033037396f434
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the measurement, adjust the delay time between the main power rail and reset signal to 7ms in order to match the spec. of touch controller, eKTH7918U.
BUG=b:184126265
BRANCH=firmware-volteer-13672.B
TEST=build test firmware and verified by EE team.
Change-Id: Iea84046c1b1f3fe6ab8bb89d86d00b1e89325f71
Signed-off-by: Hao Chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add control charging current from TSR0 and correct charger_perf table value.
BUG=b:179067801
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Ie0d969898defe76952e5c136fa93b7edffe51de3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Edward Doan <edoan@google.com>
Condition use of RO_VPD for LAN MAC address on CONFIG_VPD rather
than CONFIG_CHROMEOS.
Test: build/boot google/{beltino,jecht} with RO_VPD propagated from
stock firmware, verify MAC address set correctly.
Change-Id: I1606fe1936ccee6e03dee145901767c8e73bfe2d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52517
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Metaknight has two daughter-board (DB_PORTS_1A_HDMI and
DB_PORTS_LTE_HDMI), LTE and USB Type A use the same usb port,so needs to
probe daughter-board to avoid USB device cannot recognize correctly.
BUG=b:184809456
TEST=build and verify USB device can recognize correctly
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie42d12c7ce5c7341751c3cf92b5f37b6cd4d479f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Kaiyen Chang <kaiyen.chang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 1e36dc078e. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Change-Id: I921dc5c814e5187dce283eeff43075b59885723a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52418
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Ensure the ChromeOS FMAPs are used only when CONFIG_CHROMEOS
is selected, so non-ChromeOS targets use the default x86 FMAP.
Change-Id: Id5d3e7a44973f2fadba3ea15e0e544eee7fa53e6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
EN_SPKR is routed to SD pin in the ALC1019 speaker amplifier. The
concerned pin has a voltage rating of 1.8V whereas the EN_SPKR GPIO has
a voltage rating of 3.3 V. The schematics has been updated to bridge the
gap. So enable the speaker amplifier by default and add a gpio override
table to disable the speakers before board version 2.
Also update the codec ACPI HID name for the kernel machine driver to
probe the codec successfully.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the GPIO output state
is high.
Change-Id: I32b29bfae9bc94b5119b33a535d8bc825ef89445
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52355
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the ACPI objects for
machine driver is populated.
Change-Id: I8ed474d25273082d1e0742ba93746d97930deb19
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI code to enable the backlight when we enter the OS.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3e0a6c06120ac5abf0a0d82494e03d9cf80c1f8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52113
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both touchpads supported by zork use level-triggered wakeup signal.
BRANCH=zork
BUG=b:172846122,b:182911201
TEST=1. cros build-ap -b zork
2. both Synaptics and ELAN touchpads work fine on Vilboz
3. Wakeup source is correctly reported on Vilboz
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: Icc2b5ad3bd434c9759a0fdfc121aa3c94f46630e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52367
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the datasheet provided by ELAN, the /INT pin is "low active"
and "indicates touchpad likes to send data to system(host) when low".
The signal is level-triggered.
BRANCH=zork
BUG=b:172846122
TEST=cros build-ap -b zork
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I1f2182aaf483932304591ab14592f35214ea6efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52366
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add uart controller to chipset.cb and leave it off by default.
Turn uart0 on for console for mainboards.
BUG=none
TEST=builds and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Iaeb7fea4b92bd89331c7ae7c1c000f8d9961fe9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
TCSS OC pins has not been correctly configured for brya.
This patch fills the value from devicetree to correct the OC pins
mapping
BUG=b:184653645
BRANCH=None
TEST=check if UPD value has been reflected correctly
Change-Id: Ia21cdbf5768ad7516ea52bff7e247291a7d2ebd1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add log to show the codec has been disabled.
BUG=b:185193926
TEST=cbmem -c | grep disabled, can find the codec name
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8ce7e435ce73beb2a5cbf5883905554227b1989b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
This is the same as zork.
BUG=b:184126844
TEST=Boot guybrush in developer mode and switch to normal mode.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib11c255ab7e937de334ecd18dc030006f7724275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
platform_descriptors.h is unrelated to the contents of baseboard/gpio.h
where it was included, so move the includes to the files where it is
actually needed.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94e59b5aac2df834d956106ac953eebfc5cf6921
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52357
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The board's ec.h file defined EC_SCI_GPI as GEVENT_24, so use that
definition in all places in the mainboard code instead of a mix of the
board specific define and the SoC's GEVENT number define.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46525ed24e9993acd3d850959dd63761a690d5df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Enable CRFP power control in gpio table. RST needs to drive low
before PWR enable. Since reset signal is asserted in bootblock,
it results in FPMCU not working after a S3 resume. This is a known issue.
BUG=b:181377402
BRANCH=None
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8a8fae80c3cc186e0a097ab2007abb656f382cbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:175364713,b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I9cf4d51f42fe250340bcb642db07796c9a480c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52312
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I102c1c5f8215a6c5f7a4451f5731167c32e27c90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52313
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The first CSE Lite SKU is available, therefore enable the Kconfig
option to have the CSE reboot the system into its RW FW during a cold
boot.
BUG=b:183826781
TEST=50 cold reboot cycles
Cq-Depend: chrome-internal:3758108
Change-Id: Ib3a1a9f8ac51bdab8858b2764d5bc0f6f07987cc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Lillipup add two sku for OLED panel.
Additional VBT is necessary to modify PWM source from VESA eDP AUX
interface
BUG=b:183630802
TEST=emerge-volteer coreboot-private-files-baseboard-volteer
check vbt_oled.bin is under build folder and check in CPU log.
Cq-Depend: chrome-internal:3744227
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I576297b8296def3c37a01ae0223fa332aa9f02b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52150
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Sync from guybrush.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ica4e6511a5106a958567565b96d5888b8c829ff2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
To update the sx9324 registers after RF team fine-tuned the parameters.
BUG=b:172397658
BRANCH=firmware-zork-13434.B
TEST=build coreboot and verify the sx9324 function
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ief85bc61952144a1d7a151100d89938517078ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51936
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To enable WWAN we want to release it from reset start.
BUG=b:180166408
TEST=WWAN enumerates on brya
Change-Id: I4f9884d3b2fc8822dda1a6fe743c863aa6c696da
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52199
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable I2C2 in devicetree and fill ACPI information for Codec.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib75ef99cbca8b2f38268705704e7616b456f19d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7661dea682cbe0ae5e169d87e794ed6ed3c83b5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The intel/soc/broadwell smihandler has no handler for this APM call.
Change-Id: I2bcec7cce00d433a197a9e2fb01434a2998e1452
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52167
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
On Hayato Chromebook this can save ~100ms in total.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f58d203e969dc1a13a479d7dc63b1b162a9ae3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51973
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the ACPI name from AMDP1015 to 1002105 based on b/177971830#180.
AMDI1015 -> AMD platform with RT1015
10021015 -> AMD platform with RT1015p
Reference:
https://www.spinics.net/lists/alsa-devel/msg124694.html
BUG=b:177971830
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage, then verify with ALC1015 AMP
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id8f378ad6f3328d7db949ecdb609a2f16acd3884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52127
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Guybrush doesn't have a PS/2 mouse.
BUG=none
TEST=boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I87e51d23b69cfd6ad7bb88b364714d679e92728f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
WFC Camera driver will control the power sequence.
Therefore, set default to low.
BUG=b:184024459
TEST=abuilds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7ce25b83a715a022e36289dc0abf0d39f5798eb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is a temporary workaround for a bug that breaks graphics due to
some power management issue.
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c8ff8e827901112fd8b2e993898006bc133241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52141
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
pcie_rst isn't working correctly, so use the AUX resets to reset the
PCIe devices before training.
BUG=b:182202136
TEST=See PCIe devices train & enumerate
Change-Id: I6db21c79dcbd40c7a8c3f01c60b02882a3851278
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I07d5c46d6ea6dc2bc9ab265d0c01772d653884cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit 52e6194558.
Reason for revert: Graphics actually works now. I should have abandoned this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I83aac3a2c616bb434706f23e36549760bc764080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Enable Bayhub SD card reader power-saving mode for Lindar and Lillipup.
BUG=b:173676531
TEST=Boot to OS and test with SD card function.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I923d6e1beacd007c0e501f39c1f434c3e1085b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Config ANX7625 line data end same time on all line.
BUG=b:173603645
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: Ia1dc217138a98a79ef2f31225b52ba2b1aaf8672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This is locking up the OS. For now this will unblock booting.
BUG=b:183971103
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id2b96eedf38c9038169407418c6d36f13299fb62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Current get panel_id is over sku_id() >> 4, but sku_id is combined with
wfc_id/lcm_id/sku_id, so the panel_id value is wfc_id << 4 | lcm_id()
in fact. When wfc_id is not 0, the panel_id will be wrong. So only get
the low 4 bits for the panel_id.
BUG=b:183779755
BRANCH=kukui
TEST=emerge-kukui
Change-Id: I63e0c8a2719462a9b979afe52a27c78b9fc804e8
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The EDID and initial code are provided by STA (the vendor).
BUG=b:183969078
TEST=Boots on Chromebook Katsu and displayed developer firmware screen
successfully.
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I54e72c072b47d2be264ed7f0700812a6c704a104
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51918
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The recent refactor of console UART GPIOs to mainboard's bootblock
caused brya boards to lose the first ~5 lines of the logs from
bootblock. Rename bootblock_mainboard_init to
bootblock_mainboard_early_init so that the UART pads will be ready
by the time the console is initialized.
BUG=b:184319828
TEST=First lines from report_platform.c are now seen in UART output
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a4fadcc091bf9b1c9894f9afaf42baff63c73a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Enable I2C2 in devicetree and fill ACPI information for Codec and
Speaker amplifiers. Pass correct IRQ GPIO for headset jack.
BUG=None
BRANCH=None
TEST=Ensure that the Codec and Speaker Amplifiers are detected in
i2cdetect.
Change-Id: I1ae52a8bbaa0181c906cd14a94de22e0250ed4c1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52046
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
Add USB ACPI configuration for BT device.
BUG=b:182201890
TEST=Build and boot to OS.
Change-Id: I647c301e2db6d4a7c5c8cb31cbc47a44cba5e734
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure camera power GPIO to high
BUG=b:182207799
TEST=Build and boot to OS then checked camera device existence with lsusb
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ie894167e3c4f8efdb3710599c6ff3a9fc975adb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Initialize all eSPI signals including PCIE_RST0_L early for EC
communication.
- Set PCIE_RST0_L to a GPIO and set it high to release the bus. This is
a temporary workaround until PCIE_RST_L comes up on its own.
- Make sure all GPIO muxes initialized early are re-initialized.
BUG=b:183340503
TEST=Boot Guybrush
Change-Id: I512cb8b435dc8412cd46189e741ad94e5a24699e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51675
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mancomb does not have a dedicated SCI pin so it uses VW.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id315ab448209d9c93494f7689361e45f8a6ed001
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Configure I2C rise/fall time in device tree to ensure I2C CLK runs
accurately at I2C_SPEED_FAST (< 400 kHz).
Measured I2C frequency just as below after tuning:
I2C0(touchpad): 385 kHz
I2C4(audio): 380 kHz
BUG=b:180335053
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: Ic92ee0379456e80260a8026bc38ee41325dad6d2
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
There are forthcoming designs that will be utilizing
a discrete TPM 2.0 solution. Split the existing dedede
configuration options so future mainboard variants can
easily select the appropriate Kconfig option using the
newly introduced options:
- BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50
- BOARD_GOOGLE_BASEBOARD_DEDEDE_TPM2
The existing variants all select the former option,
BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50 since all those
designs currently utilize Cr50.
BUG=b:184151664
Change-Id: I2bdb1ca4fd78cc0628256d49678ea042c55f6fba
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52030
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP v2081 has a bug where it uses the information about south XHCI
ports to enable TCSS XHCI ports. This change works around this bug by
enabling south XHCI ports 1 and 2 in brya baseboard devicetree. brya0
already enables south XHCI port 1 in overridetree.cb, however, it is
still enabled in baseboard/devicetree in case more variants are added
to brya before FSP is fixed.
BUG=b:184324979
TEST=Verified that TCSS XHCI ports 1 and 2 are now enabled.
Change-Id: I4b86a98b18234ba309ddf2f30b80d78472951637
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There's no good reason to use values smaller than 2 GiB here. Well, it
increases available DRAM in 32-bit space. However, as this is a 64-bit
platform, it's highly unlikely that 32-bit limitations would cause any
issues anymore. It's more likely to have the allocator give up because
memory-mapped resources in 32-bit space don't fit within the specified
MMIO size, which can easily occur when using a discrete graphics card.
Change-Id: If585b6044f58b1e5397457f3bfa906aafc7f9297
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52072
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that the EC Software Sync
is complete.
Change-Id: Id8655b6f805e14ce3cb71777c1cc175f45841fcc
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable Touchpad by configuring the enable GPIO to logic high. Add
touchpad configuration for ELAN touchpad.
BUG=b:182207444
TEST=Build and boot to OS in Guybrush. Ensure that the trackpad events
are detected using evtest.
Change-Id: Ib47fbb33f2b181eb85f6ded98a5b0ce08fbc7b64
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51962
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change disables touchpad interrupt, as it sends spurious wake signal
via GPP_F14 and immediately wakes the system from S3. It happens because
touchpad's power is gated by deassertion of PLTRST#. The behaviour for
S0ix is unchanged.
BUG=183738135
TEST=manually
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ia7d282f38d205a94cc43eaa1832729f4606437c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51831
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change exposes the PCH_INT_ODL line in GPP_F17 as interrupt resource for
CREC device
BUG=none
TEST=manual test
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I0c05160cb7894b5f7beee93a0c93776f973eae56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
PCH_INT_ODL (GPP_F17) is used to wake AP from S3, however it was configured
to reset state on PLT reset assertion. This change reconfigures the pad
using DEEP instead of PLTRST to retain pad configuration across S3.
BUG=b:178545523
TEST=manual: verified that asserting PCH_INT_ODL wakes system and the wake
source is GPP_F17
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I8df5dafedabc7b6af74c39621f0e1eb7019a9a17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We've mostly stopped using Trogdor-rev0 now and are starting to bring up
rev2 instead. Therefore, the default revisions this builds for should be
the newer ones.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie433ebb2a03fb1636b5012b4a0567ba6f982579d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52007
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The is used for AMD Grunt board which uses ALC5682 and MAX98357 codec.
kernel driver will need to retrieve MISC FCH memory resource for CLK
enabling per different CID/HID.
BUG=b:171755306
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I5f29a2d784a9fc749fff61a9c96c0a487b71a2d7
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51659
Reviewed-by: Yu-hsuan Hsu <yuhsuan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Acoustic noise mitigation for lantis and set slew rate to 1/4
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:183561593
BRANCH=dedede
TEST=EE verify acoustic noise test passes.
Change-Id: I5e5f24ed934910726c220678068d085b6ee2bcf6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Needed so get_lid_switch will actually call the EC. Otherwise it
returns -1.
BUG=b:183524609
TEST=Depthcharge no longer halts complaining that coreboot didn't sample
the pin
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4639b3713d726192e251dcffa14381dd92518fa2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
It looks like we are having SI issues on eSPI at 33 MHz. Switching to 16
MHz makes everything a lot more stable.
BUG=b:183524609
TEST=Boot to OS and run `ectool version` 1000 times and see no problems.
Before with 33 MHz there was an error every few cycles.
declare -i i=0; while ectool version; do i+=1; echo "$i"; sleep .11; done; echo "Finished: $i"
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ab515629703a157c1d1ac6adcf5cf379e80f8ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Move the parts of romstage.c that populate the UPD-M data structure to
the newly created fsp_m_params.c file. Since
platform_fsp_memory_init_params_cb gets called from the FSP driver and
not directly from car_stage_entry the two code parts in romstage.c
weren't directly interacting. Since soc/romstage.h only contains the
mainboard_updm_update function prototype, rename it to soc/fsp.h. This
patch also removes a few unused includes.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I52c21f13520dbdfab37587d17b3a8a3b1a780f36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Now that we have the DISABLE_KEYBOARD_RESET_PIN Kconfig option, select
it and remove the temporary workaround that was implemented in the
mainboard code in commit 39ef890336.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I634d11290dad8c93f10979f06243b1bf84737ae2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Thermal sensor2 defined in baseboard do not exist in boten.
With the format the DPTF policies are defined in boten, all the entries
from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI table
and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in boten. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Change-Id: I63c781e0a439f1e7a3525fa7cf290fa9300cb066
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original Stamp_boost parameter will cause boost time over 2500sec(3960sec)
To pass balance performance and skin temperature test, decrease stamp_boost:
2500 -> 1640
BUG=b:182753072
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test
Change-Id: I43c104ef912aafecadf9497f9ea20c8478c0e920
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The Type-C subsystem ("TCSS") IP block is similar between TGL and
ADL. For pre-boot purposes, the limited amount of functionality required
appears to be common between the two, therefore move the functionality
to intel/common/block and rename from `early_tcss to `tcss` along the way.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1c6bb9c7098691f0c828f9d5ab4bd522515ae966
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51753
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Caroline has a Wacom W9013 digitizer on I2C2, which was
incorrectly disabled in commit d957d12e6
[mb/google/glados: clean up variant devicetrees]
as part of preparation for converting to overridetree format.
Test: build/boot, verify digitizer now available under Linux
Change-Id: I234bc0126b5d13c22a663d6544382890b312ce63
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds support zinitix touchpad for sasuke.
BRANCH=dedede
BUG=None
TEST=built and checked touchpad worked on sasuke
Change-Id: I85794311c49e33c4683482e125bea5ca2dbacfa8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ANX7625 requires customized hs_da_trail time.
So override the data trail for ANX7625.
BUG=b:173603645
BRANCH=kukui
TEST=Display is normal on Jacuzzi
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I620035363507daaa19e3c272a44059c17be29af1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Lists of changes:
1. Rename MISCCFG_ENABLE_GPIO_PM_CONFIG -> MISCCFG_GPIO_PM_CONFIG_BITS
2. Move MISCCFG_GPIO_PM_CONFIG_BITS definition from intelblock/gpio.h to
soc/gpio.h. Refer to detailed description below to understand the
motivation behind this change.
An advanced GPIO PM capabilities has been introduced since CNP PCH,
refer to 'include/intelblock/gpio.h' for detailed GPIO PM bit definitions.
Now with TGP PCH, additional bits are defined in the MISCCFG register
for GPIO PM control. This results in different SoCs supporting
different number of bits. The bits defined in earlier platforms
(CNL, CML, ICL) are present on TGL, JSL and ADL too. Hence, refactor the
common GPIO code to keep the bit definitions in intelblock/gpio.h, but
the definition of MISCCFG_GPIO_PM_CONFIG_BITS is moved to soc/gpio.h so
that each SoC can provide this as per hardware support.
TEST=On ADL, TGL and JSL platform.
Without this CL :
GPIO COMM 0 MISCCFG:0xC0 (Bit 6 and 7 enable)
With this CL :
GPIO COMM 0 MISCCFG: 0x00 (Bit 6 and 7 disable)
Change-Id: Ie027cbd7b99b39752941384339a34f8995c10c94
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set default USB2 HS disconnect threshold to maximum to avoid false
disconnects that eventually lock up the xHCI controller
BUG=b:174538960
TEST=suspend_stress_test -c 50 on vilboz and morphius.
Sample set of USB2 HS devices connect and disconnect
successfully
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ic921d850a0bdd717a2a7e50e9e6f65e39e0607bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51265
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The previous "PCIe port" numbering was incorrect and resulted in several
PCIe devices failing to enumerate. With lane reversal, these numbers are
all backwards. This explains the confusing mapping of Clock Source #1 to
Root Port #9 in https://review.coreboot.org/c/coreboot/+/50101. We were
confusing "Root Port" vs "PCIe Lane".
This change addresses the port vs. lane confusion in the device tree
configurations. It also adds more detailed documentation to a future
reader (i.e., me) to avoid this blunder.
BUG=b:181633452,b:181635072,b:177752570
TEST=build AP firmware; flash device
BRANCH=none
Change-Id: I47edf0b0af1bdcf86b89f17ad2a1f128ef9e9f7a
Signed-off-by: Joe Tessler <jrt@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
After revisiting the genesis GPIO table and schematics for EVT closure,
I discovered several missing and/or incorrectly documented GPIO pin
mappings.
Now the GPIO pin names and functions should match what's written in the
latest schematics.
BUG=b:181633452,b:181635072,b:177752570
TEST=build AP firmware; flash device
BRANCH=none
Change-Id: I73e6733bce761b00717091834c7a49e85154f80b
Signed-off-by: Joe Tessler <jrt@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51677
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With this change, only raminit.c uses pei_data.h definitions. With MRC
cornered, making it optional is just a matter of writing a replacement.
USB config definitions will be moved to Lynx Point code in a follow-up.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4bc405213e9b0828d9ced18677335533c7dd381d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add memory table to "mem_list_variant.txt", and command to generate files:
go run ./util/spd_tools/lp4x/gen_part_id.go src/soc/intel/tigerlake/spd src/mainboard/google/volteer/variants/collis/memory/ src/mainboard/google/volteer/variants/collis/memory/mem_list_variant.txt
DRAM Part Name ID to assign
MT53D512M64D4NW-046 WT:F 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
BUG=b:182227204
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I773c65c0b6d5e868572530305ab8a61a0dd1532d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. H9HCNNNBKMMLXR-NEE
2. MT53E512M32D2NP-046 WT:F
3. K4U6E3S4AA-MGCR
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iacfdd9a27f126ba4b97d1a6493bcc09bb31454a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51619
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow schematic to modify USB port settings.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 0
USB2 [3]: LTE
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: Camera WFC
USB2 [7]: Integrated Bluetooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: LTE
BUG=b:182973703
BRANCH=dedede
TEST=Build the coreboot image.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I80447d6ac3422f858a9022f550b4f42353819405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change allows guybrush EC communication while other patches
in the SOC code are worked on.
BUG=b:183149183
TEST=Boot guybrush with EC comunication
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I56fb64d4c065cf0665025346218cc66d77dacb52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51665
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO129 is muxed with KBRST, so setting GPIO129 to low causes reset
when KBRSTEN is set to 1. Since reset value of KBRSTEN is 1 we need a
logic to clear it.
BUG=b:183340503
TEST=build
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I194e8432a14d6105f6bcf12111647f5aad4e2de2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Modify power sequence of touchpad to meet the definition in the spec.
BUG=b:178353432
BRANCH=firmware-volteer-13672.B
TEST=build test firmware and verified by EE team.
Change-Id: I8b8e383223d017223c36044efdf21738fe26d2ea
Signed-off-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51514
Reviewed-by: Hao Chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the MRC cache API for asurada, and sync dramc_param.h with dram
blob (CL:*3674585). With this change, the checksum, originally stored in
flash, is replaced with a hash in TPM. In addition, in recovery boot,
full calibration will always ne performed, and the cached calibration
data will be cleared from flash.
This change increases ROMSTAGE size from 236K to 264K. Most of the
increase is caused by TPM-related functions.
Add new API mtk_dram_init() to emi.h, so that 'dramc_parameter' can be
moved to soc folder.
With this CL, there is no significant change in boot time. Normal AP
reboot time (fast calibration) is consistently 0.98s as before, so
this change should not affect the result of platform_BootPerf.
BUG=b:170687062
TEST=emerge-asurada coreboot
TEST=Hayato boots with both full and fast calibration
BRANCH=none
Cq-Depend: chrome-internal:3674585, chrome-internal:3704751
Change-Id: Ief942048ce530433a57e8205d3a68ad56235b427
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This patch makes all Octopus variants resume from S0ix/S3 on AC plug
and unplug.
Change-Id: Iab054d77368bf2047b6d523188b8c401a7643aaa
Signed-off-by: Derek Basehore <dbasehore@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It's common to use the raw, unshifted I2C address in coreboot. Adapt
mainboards accordingly and perform the shift in MRC glue code.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4e4978772744ea27f4c5a88def60a8ded66520e1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51458
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
eDP panel flicker during system idle state is observed.
Disabling USB2 SUS well power gating can remove flicker symptom.
Please refer to doc#634894 for more details.
BUG=b:182323059
BRANCH=None
TEST=Boot and confirm no display flicker.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: Icadf9c494fab82b219317c3ca3b04f633b543083
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add SPD support to eldrid for DDR4 memory part H4AAG165WB-BCWE.
Eldrid should use DRAM_ID strap ID 4 (0100) on SKUs populated
with H4AAG165WB-BCWE DDR4 memory parts.
BUG=b:181732562
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Change-Id: I38cfe3eb26b00563ce17df3a3ac2a0a846f2ae00
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51667
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the cret variant of the waddledoo reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:181325655
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CRET
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I700201cf81b25c6776df3ec9fc843cd9bd8c88c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Do not use the same name as the non-LP GPIO config. This allows checking
at build-time that a mainboard uses the correct GPIO config format.
Without this commit, there are no build-time errors when using the wrong
format of GPIO config, but there would be undefined behavior at runtime.
Tested by trying to build asrock/b85m_pro4 and hp/folio_9480m after
toggling the `INTEL_LYNXPOINT_LP` Kconfig option (and trimming down the
USB config arrays for asrock/b85m_pro4). In both cases, building failed
because the necessary GPIO config global is not defined, as expected.
Change-Id: Ib06507ef8179da22bdb27593daf972e788051f3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51661
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To append SSFC to top 32 bits of fw_config.
BUG=b:177971830
BRANCH=firmware-zork-13434.B
TEST=Build coreboot and get the value of SSFC.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Iab1596f1cc8fbbf45e6a9269351bf422a43f3583
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51655
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add USB Port configuration into devicetree for storo
BUG=b:177389444
BRANCH=dedede
TEST=built firmware and verified USB3.0 function is OK
Change-Id: I1527c7178ffac9b2322eb65aab6e2086d949e47c
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Not all of dalboz variants support the this amp. Thus, move out of baseboard.
BUG=b:182815488
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If708574f5fb18dd3b4f2ef978529a16a40d5dc0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-hsuan Hsu <yuhsuan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
The logic behind I2C bus initialization, I2C MMIO base address getter
and setter, I2C bus ACPI name resolution are identical for all the AMD
SoCs. Hence moving all the SoC agnotic parts of the driver into the
common driver and just configure the SoC specific parts into individual
I2C drivers.
BUG=None
TEST=Build Dalboz and Grunt. Boot to OS in Dalboz. Ensure that the I2C
peripherals are detected as earlier in Dalboz. Verify some I2C
peripheral functionality like trackpad and touchscreen.
Change-Id: Ic9c99ec769d7d8ad7e1e566fdf42a5206657183d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Suggested-by: Kyosti Malkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51509
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a new variant called Marzipan that is identical to Lazor
for now.
BUG=b:182181519,b:182018606
BRANCH=master
TEST=make
Change-Id: I92b667c63b0a06255d1e9511d7486293d8b4426a
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add support SPI_FLASH_GIGADEVICE for some project.
BUG=b:182246432
BRANCH=trogdor
TEST=emerge-strongbad and test with power on.
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Change-Id: I6ab948909f4e17b4b992be6d699646f7a62bef7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
elemi does not use the GPP_B7/GPP_B8, so config to NC.
Currently, there is no functional impact.
BUG=b:182981460
TEST=emerge-volteer coreboot, boot into OS, and suspend/resume
successfully.
Change-Id: I7b491fd595b0e77e6dcce08e3172dbe592f63c37
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. Adjust `mb_get_spd_map` to take a pointer to
a struct instead of an array, and update all the mainboards accordingly.
Currently, the only board with memory-down in the tree is google/slippy.
Mainboard code now obtains the SPD index in `mb_get_spd_map` and adjusts
the channel population accordingly. Then, northbridge code reads the SPD
file and uses the index that was read in `mb_get_spd_map`, and copies it
to channel 0 slot 0 unconditionally. MRC only uses the first position of
the `spd_data` array, and ignores the other positions. In coreboot code,
`setup_sdram_meminfo` uses the data of each SPD index, so `copy_spd` has
to account for this.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Ibaed5c6de9853db6abd08f53bbfda8800d207c3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51448
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MRC only uses the SPD data for the first index, and ignores the rest.
Moreover, index 1 corresponds to the second DIMM on the first channel,
which does not exist on ULT (only one DIMM per channel is supported).
Copy the SPD to the first DIMM on channel 1 instead. Adjust northbridge
code to retrieve the serial number from the correct SPD data block.
Tested on Google Wolf, both channels are still correctly detected.
Change-Id: Ic60ff75043e6b96a59baa9e5ebffb712a100a934
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SLP_S0_GATE# signal is used in conjunction with the PCH's SLP_S0# to
provide an indication to the rest of the platform when the system is
entering its software-initiated low-power state (i.e. S0ix). This lets
the platform distinguish between opportunistic S0ix entry and the runtime
suspend mechanism.
BUG=b:180401723
TEST=abuild
Change-Id: I7fe2e3707465778baf56283617a8485a94f2dbca
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50881
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I9896db41dbe2812856357510bc4420482e73ab3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51547
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure early GPIOs in verstage if it is run in PSP otherwise
configure them in bootblock.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic1faeea59462319c1652c69034b4dde01669e13b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
In pursuit of the goal of eliminating the proliferation of raw region
devices to represent CBFS files outside of the CBFS core code, this
patch removes the get_spd_cbfs_rdev() API and instead replaces it with
spd_cbfs_map() which will find and map the SPD file in one go and return
a pointer to the relevant section. (This makes it impossible to unmap
the mapping again, which all but one of the users didn't bother to do
anyway since the API is only used on platforms with memory-mapped
flash. Presumably this will stay that way in the future so this is not
something worth worrying about.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iec7571bec809f2f0712e7a97b4c853b8b40702d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently, if `get_wifi_sar_cbfs_filename()` returns NULL, then
`get_wifi_sar_limits()` assumes that the default filename is used for
CBFS SAR file. This prevents a board from supporting different models
using the same firmware -- some which require SAR support and some
which don't.
This change updates the logic in `get_wifi_sar_limits()` to return
early if filename is not provided by the mainboard. In order to
maintain the same logic as before, current mainboards are updated to
return WIFI_SAR_CBFS_DEFAULT_FILENAME instead of NULL in default
case.
Change-Id: I68b5bdd213767a3cd81fe41ace66540acd68e26a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51485
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that SAR support in VPD is deprecated in coreboot, there is no
need for a separate Kconfig `WIFI_SAR_CBFS` as the SAR table is only
supported as a CBFS file. This change drops the config `WIFI_SAR_CBFS`
from drivers/wifi/generic/Kconfig and its selection in
mb/google/.../Kconfig.
wifi_sar_defaults.hex is added to CBFS only if
CONFIG_WIFI_SAR_CBFS_FILEPATH is not empty because current mainboards
do not provide a default SAR file in
coreboot. Thus, CONFIG_WIFI_SAR_CBFS_FILEPATH is updated to have a
default value of "".
BUG=b:173465272
Cq-Depend: chromium:2757781
Change-Id: I0bb8f6e2511596e4503fe4d8c34439228ceaa3c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
If we spot any error in the file, treat it as untested and
broken copy-paste.
Change-Id: Idd13b8b006fce7383f3f73c3c0a5d51a71c0155b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38313
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add USB Port into devicetree for storo
BUG=b:177389444
BRANCH=dedede
TEST=built firmware and verified USB3.0 function is OK
Change-Id: I4d5160ff23d2bd386cb33164b580e6d6f3bf30fd
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add camera support in devicetree and associated GPIO configuration.
BUG=b:181729304
BRANCH=dedede
TEST=built blipper firmware and verified camera function is OK
Change-Id: I806ec207a454d4383aca093159553b7e618e16b2
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add G2 and ELAN touchscreen into devicetree for blipper.
BUG=b:181098785
BRANCH=dedede
TEST=built blipper firmware and verified touchscreen function is ok
Change-Id: Ie0bfc2972fc1a33a6f02495d3976b816209e956b
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configuring GPP_B7 as GPO_HIGH.
Sasuke doesn't have SAR sensor, GPP_B7 is routed to the LTE module
and is kept high so that the LTE module uses the default emission power.
BUG=b:180492044
BRANCH=firmware-dedede-13606.B
TEST="FW_NAME=sasuke emerge-dedede coreboot"
Change-Id: Ib38c649830db2291b3a2a771f5c884acf37dcbeb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51049
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Guybrush does not have a dedicated SCI pin so it uses VW.
BUG=b:181134664
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I12fb7c23718ad2350478b89b321e9f0aa099e53b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51238
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the temperature sensors defined in baseboard do not exist in
magolor. With the format the DPTF policies are defined in magolor, all
the entries from the baseboard are included and then the overrides
applied. This causes the non-existent DPTF devices to be exported in
the ACPI table and in turn OS reading invalid temperatures. Fix the
format for DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in magolor. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I43f0b188e49e24657db055ce898ce159d499a22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Some of the temperature sensors defined in baseboard do not exist in
madoo. With the format the DPTF policies are defined in madoo, all the
entries from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI
table and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=b:182513022
BRANCH=dedede
TEST=Build and boot to OS in madoo. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Idc5d0b357d61b9346b4d20ec8322b124c9655b4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Disable SA GV, because factory used Samsung memory with wrong date code.
So we need to use board version to identify build MB phase to disable SA GV.
Disable SA GV when board version equal one.
BUG=b:179747696
BRANCH=firmware-volteer-13672.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I51f4adcf0dd8dbf1cf39d8aec6e4303565551e5f
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add P-sensor into devicetree for storo according to
configuration information provided by the vendor.
BUG=b:177392203
BRANCH=dedede
TEST=built storo firmware and verified P-sensor function
Change-Id: Iced4ab7d94b38ef8b1807955cbb887454accb1e8
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
To support mipi camera.
1. enable DRIVERS_INTEL_MIPI_CAMERA/SOC_INTEL_COMMON_BLOCK_IPU
2. add IPU/VCM/NVM/CAM1 into devicetree
To support usb camera.
add camera support in devicetree and associated GPIO configuration.
BUG=b:177393430, b:177388006
TEST=Build and boot to OS. Camera function is OK.
Change-Id: I98d5708d1955406c2e46db972903057bb3d12dcc
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50995
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the CNVi BT PCI config and add BT flag. There is no PCI host interface
in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS to make sure BT is
enumerated.
Change-Id: Ic700021d7a09be63ffc2715f31992257e2e893af
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50898
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
update the DPTF parameters received from the thermal team.
BUG=b:181627614
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: Ied6b71d9285662a70446af2e781b630e184c3b19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joe Tessler <jrt@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Remove the CNVi BT PCI config and add Bt flag.
There is no PCI host interface in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS.
Change-Id: I7e8ca1bb6a57721a72478137612d7a9c391ca0b2
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the collis variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:182227204
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_COLLIS
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ibcf8b59b38d02517cea0a3ee474ff82fc0a2a958
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This patch overrides the get_wifi_sar_cbfs_filename()
to return different sar table according to the sku id.
BUG=b:173465272
TEST=checked bios log and the correct sar table was loaded.
Change-Id: Ia30d760b1a029197d470818c73bfd2c00514652d
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use gpio_keys driver to add ACPI node for pen eject event.
Also setting gpio wake pin for wake events.
BUG=b:175519097
BRANCH=firmware-volteer-13672.B
TEST=build and verify on a Copano
Change-Id: Id0a132aa398abde4983af123d00e355ac61839a8
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51249
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Lindar/Lillipup uses the WIFI_SAR_ID field in FW_CONFIG to pick which
SAR table to load.
BUG=b:178302811
BRANCH=volteer
TEST=build and test no lindar/lillipup
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ibe829062033ba8246b9d9550cdcdc360f5f67dd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Add FW_CONFIG WIFI_SAR_ID fields in devicetree.
BUG=b:178302811
BRANCH=volteer
TEST=build and test on lindar/lillipup
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I7ec37b80ffca6924f1f0952dcfbc43c378a70923
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51386
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fleex will use SSFC to support RTL5682.
BUG=b:178653122
TEST=abuild
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icb06eabe297c5562bd2171b52cc9671c342e6dfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Update GPP_A10 and GPP_H17 configuration to meet LTE power sequence
specification.
- FCPO (GPP_A10) should not turned off during warm reset.
BUG=b:177177967
BRANCH=dedede
TEST=Verified LTE power signal waveforms during powering on and off
Change-Id: I469f9c94ebd6bf2b68a0edc74f229158d82d0ef8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Since no board overrides the weak get_gpe_table function,
gpe_configure_sci wasn't called for any variant, so drop the function.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3de204cc808449b625e1fa1e79fe653608e4b88a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the brya0 mainboard.
TEST=snippet from dmesg logs shows the correct resources being allocated:
PCI: 00:07.0 resource base 27fc00000 size 1c000000 align 20 gran 20 limit 29bbfffff flags 60181202 index 24
PCI: 00:07.0 resource base 83000000 size c200000 align 20 gran 20 limit 8f1fffff flags 60080202 index 20
PCI: 00:07.1 resource base 29bc00000 size 1c000000 align 20 gran 20 limit 2b7bfffff flags 60181202 index 24
PCI: 00:07.1 resource base a0000000 size c200000 align 20 gran 20 limit ac1fffff flags 60080202 index 20
PCI: 00:07.2 resource base 2b7c00000 size 1c000000 align 20 gran 20 limit 2d3bfffff flags 60181202 index 24
PCI: 00:07.2 resource base ac200000 size c200000 align 20 gran 20 limit b83fffff flags 60080202 index 20
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6b520ae50f19a730263de7918594718f3b4b1c1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51455
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 87a1bd696d.
Reason for revert: skin temperature is overheating due to boost time is too long
BUG=b:175364713
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I31db06f4bcb986398e7bd2ac2858ffbedb257e2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
The SKU ID for Asurada should come from AP ADC channel 5 and 6.
BUG=None
TEST=make; boots on asurada
Change-Id: I6a00c555f20aca4cd7f8bcee46ee81c17ef6ca3c
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Move the initialization from bootblock to romstage for following reasons:
- Follow MT8183 initialization sequence.
- PMIC and RTC functions are only called after verstage.
- Reduce bootblock size.
- PMIC initialization setting is complex and may need to be changed by
an RW firmware update.
TEST=boot to kernel successfully
Change-Id: I3e4c3f918639590ffc73076450235771d06aae91
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xi Chen <xixi.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This enables the standard library method of adding SPDs to CBFS.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I2ec94fd866409e1dfa5cb65f6960ea07cbe22f2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51022
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the option to build guybrush firmware with support for EM100.
This will assist in bringup of the new board.
BUG=b:180723776
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I2246d2952f341cd8fff8fd486cf989cdb7929411
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51071
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since not all mainboards based on the Cezanne SoC have to support ACPI
resume, select this option in the mainboard's Kconfig and not in the
SoC's Kconfig.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I988276ccb5b61837d7f3f015d1d1aba783324b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds the Guybrush APCBs into the AMD firmware binary.
BUG=b:182510885
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iba40cab1d68e9f8d7291e7d715be185a3b6249f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Configure early GPIOs in verstage if it is run in PSP otherwise
configure them in bootblock.
BUG=b:181961514, b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ib9410089592776ffe198901f2de914fd04bdbade
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
2. Add TOUCH_RPT_EN pin(GPP_A11) control to fix TOUCH_RPT_EN pin
keep high after system suspend.
BUG=b:181711141
TEST=Build and boot boten to OS.
Confirm TOUCH_RPT_EN pin keep low after system suspend.
Change-Id: I98efbe68dab538906802647582eba0e068d9c11f
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51254
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure I2C bus 5 high and low time for p-sensor device.
BUG=b:181727056
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Change-Id: I4b6d78d84b8ea145093f52bbb13684e2c6aa979c
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Function is identical for all mainboards, so factor it out.
Change-Id: Ibe08fa7ae19bfc238d09158309f0a9fdb31ad21c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50028
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
