This patch enables TPM2 on LPC and adds the needed devicetree entry for
TPM for mc_apl4.
Test=mc_apl4 flashed, booted into Linux and checked via dmesg if TPM is
present
Change-Id: I9af7e1a8623302eca46f5ecd8e498678ccda92ad
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These boards need a working VTD therefore enable this feature.
Change-Id: I74c64bf1bd66188c4c32b85c66683dafd0e1fd38
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Because of Intel's faulty LPC clock, the SERIRQ mode must be corrected.
By removing this entry from devicetree, the default value (quiet mode)
is used. The problem is described in Intel document 334820-007 under
point APL47.
Change-Id: I7a45e0e5fcde17a20abd19a33282b8a9215b1480
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31138
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TPM chip is connected to the SPI interface of APL. The proper chip
select pin needs to be used in order to access the TPM in the memory
mapped space. This needed chip select is internally (inside APL)
routable to GPIO 106. Therefore the change of GPIO 106 mode is needed to
make the TPM work on SPI bus.
TEST=Build coreboot for mc_apl2 board and check the TPM console output.
In addition the TPM was correctly verified by our Linux driver.
Change-Id: I2b0d5a6f2c230187857c2428a70de61f21da6724
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
With the commit a96e66a (soc/intel: Clean mess around UART_DEBUG), an
adjustment is necessary for this mainboard.
Change-Id: I0fb6288959f8bcb45c4cc93cc132f31a5ab2a5ad
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Enaebl the RTC driver to be used on mc_apl4.
Change-Id: Ib8d2a9f6b8cea47cd10db4dfcc59eec1b21c7993
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
On this mainboard there are legacy PCI device, which are connected to
different PCIe root ports via PCIe-2-PCI bridges. This patch disables
the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges.
Change-Id: Id36e39c4568f5dd241cd864d2e75365abd0f2a91
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29882
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I4ab40e34253c20adaacfdf42050314e06547eefb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard also has a SD slot.
Change-Id: I969e8ecb27aee4c8be212e67dfe6bd807ecd3b2f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard has four connected PCIe devices. The required root ports
are switched on and configured.
Change-Id: I82b13e1d245a172762ebd689ae136a762027033f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29810
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An additional read of PTN configuration data at the end of the
ptn3460_init function is not necessary.
Change-Id: I5f7f647242e94b1af13757d00e80ed9813d435d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The power budget for this mainboard is very limited while the
performance demand is low. Set the CPU clock to the lowest value to
enable maximum efficiency and thus lowest power dissipation.
Change-Id: I23c7c5393deb676b94f2b0ac25e21a7a44cd8cb3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard is based on mc_apl1. In a first step, it contains a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl5 mainboard will follow in separate commits.
Change-Id: Icdbb116a822ffa7a3bfb7026a5d1164db56a0c46
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Currently, there is nothing for this mainboard to do in ramstage.
Change-Id: Id74a5f3f0a0583dc6bc81044913b8bb83d3b0b93
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard is equipped with LPDDR4 modules. The corresponding memory
swizzle data must be set for this purpose.
Change-Id: I4017de0713f0df5e614086912fc39d8eb6562702
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Pöche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard also has a SD slot.
Change-Id: Id56bc1be60ec8c2be0e5543d1d8851610b7248e0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard also has an external RTC chip, but not on this bus. The
topic is currently in clarification and will be published with a later
patch. In a first step we enable all I2C busses.
Change-Id: I9ec9631ed15ab30cc6a4594531521f4a1419ad00
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Enable all PCIe root ports for this mainboard.
Change-Id: I7f6feb2f0d4c45f32d9454838e67e1a244b2712b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Ib7c4e3251545b2d32368dd56206e3b4844a24800
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
All PCIe root ports of this mainboard do not have an associated CLKREQ
signal. Therefore the ports are marked with "CLKREQ_DISABLED".
Change-Id: I834b3b0c77223d81c950e27ccfff8e9aeece2aa4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are legacy PCI device, which are connected to
different PCIe root ports via PCIe-2-PCI bridges. This patch disables
the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges.
Change-Id: I2212c1080b72a656b5c8e68b040108a7adbec608
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard provides customer hardware reset button. A feature of
this button is that it holds the APL in reset state as long as the reset
button is pressed. After releasing the reset button the APL should
restart again without the need for a power cycle. When Bit 3 in Reset
Control Register (I/O port CF9h) is set to 1 and then the reset button
is pressed the PCH will drive SLP_S3 active (low).
Change-Id: Ib842f15b6ba14851d7f9b1b97c83389adc61f50b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I1ef4a7774d4ca75c230063debbc63d03486fed6f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
For this mainboard the correction of transmit voltage swing from SATA
interface is not necessary.
Change-Id: I900d0d44b88585c223182d85c78cf3ff1e3e9159
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 2 and 3 over two
lanes (Device 13.0 and 13.1).
The following routing is required:
INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#->PIRQC#
Change-Id: I5028c26769a2122b1c609ad7789c9949e3cb7a87
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29513
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard is based on mc_apl1. In a first step, it concerns a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl4 mainboard will follow in separate commits.
Change-Id: I3dfdccc8198f3a23a45d319ede6080803a46f7f6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard variant requires GPIO adaptations to match the hardware.
Change-Id: I16387358d6c6fa15efd16f7ba7f6b89740477e9d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Disable I2C7 because there is no device connected.
Change-Id: Ie9877d40b06f4a849163a873fd308ff03995fcdc
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Enable all PCIe root ports for this mainboard.
Change-Id: I62c7ba5048b4c2288bb502a78b9621edda333f2a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Ib9ad4d9026267d2079e95245994d84c163b28dbb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
All PCIe root ports of this mainboard do not have an associated CLKREQ
signal. Therefore the ports are marked with "CLKREQ_DISABLED".
Change-Id: I59c1132c6d273ccefeb1be6243577e1ae5064ef4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard variant requires GPIO adaptations to match the hardware.
Change-Id: I4ba475e7d387f46ed5f41b7a691c7933edbc50c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard is based on mc_apl1. In a first step, it concerns a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl3 mainboard will follow in separate commits.
Change-Id: I963ec63bccf71296c3fdabfcf9f3009c2febc791
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The assignment of header->checksum was in some cases done twice, or
unnecessarily split into two lines.
Change-Id: Ib0c0890d7589e6a24b11e9bda10e6969c7d73c56
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to make the macro name consistent for all PAD_CFG1_IOSSTATE_*
macros, this change uses lower case x for *RXD*. It helps avoid
confusion when using the macros.
Change-Id: I6b1ce259ed184bcf8224dff334fcf0a0289f1788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to enable the OS SPI driver to use the software interface of
this controller the OPCODE menu has to be set up properly before
locking the controller. This is done on baseboard level so that all
variants will get this done as well.
Change-Id: I0bf0619ff0610c00325f03d13b6794aee8a62504
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/28834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
In order to minimize Electromagnetic Interference (EMI) on the LVDS
interface driven by PTN3460, clock spreading must be activated for
mc_apl1 mainboard. The modulation ratio is set to 1 % of the nominal
frequency.
Change-Id: Ie457fcdbb6239dc0b25e2c35ad7a310ee80383f9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28761
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard is based on mc_apl1. In a first step, it contains a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl2 mainboard will follow in separate commits.
Change-Id: I0af60ab0dfe556dd95da2cf1a49c685a8f0ae4eb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
In preparation for a future MC Apollo Lake board which will be equipped
with LPDDR4 modules, it is necessary to make the swizzle data
configurable. Starting from the mc_apl1 baseboard, which is equipped
with DDR3L memory and therefore does not need swizzle data, the
structures are initialized with zero.
Change-Id: I4954d0a00d1d5fc28a8dda45a9fb27f98d5c3f1e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3.
Change-Id: I116802cd2a944658fc3022e948eba43cebe52bb4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As far as I can see this Kconfig option was used wrong ever since it
was added. According to the commit message of 107f72e (Re-declare
CACHE_ROM_SIZE as aligned ROM_SIZE for MTRR), it was only necessary
to prevent overlapping with CAR.
Let's handle the potential overlap in C macros instead and get rid
of that option. Currently, it was only used by most FSP1.0 boards,
and only because the `fsp1_0/Kconfig` set it to CBFS_SIZE (WTF?).
Change-Id: I4d0096f14a9d343c2e646e48175fe2127198a822
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Platforms with LATE_CBMEM_INIT were agreed to be
removed with 4.7 release late 2017.
Change-Id: I0ecbb40f8c7ebdf68217f50af5624905d9005c64
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Since the SIOW method doesn't use any arguments, don't pass it any,
and initialize it as not using any.
Change-Id: I3fa2ab8afb7d09c176a94bbd1db27587c36030cd
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use of device_t has been abandoned in ramstage.
Change-Id: If67ea25a9e1363dde8aefe62b92ee7a61f0458b0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Change OEM ID values to 6 characters to fix error compiling with IASL
version 20180427.
Also update table creator to 8 characters from 7.
Change-Id: Id6c9a7b08dc4a9efeb69011393e29aa5a6bc54c4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The following things are specific characteristic of mc_apl1 board
variant:
- initialization for the eDP to LVDS converter
- enable decoding address range for COM 3
- legacy IRQ routing for PCI devices
- wait function for old legacy devices
- set coreboot ready LED
Change-Id: I5c853e6caae6cc880ead436f232cabddeee6d09a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25822
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Siemens will provide further boards based on Apollo Lake. These differ
only slightly. To avoid copying the complete directory of the reference
board we simply create variants that only contain the differences, like
google/reef does.
To further the ability of multiple variant boards to share code provide
a place to land the split-up changes. This patch provides the tooling
by using a new Kconfig value, VARIANT_DIR, as well as the Make plumbing.
The directory layout with a single variant mc_apl1 (which is also the
baseboard) looks like this:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/mc_apl1 - code
variants/mc_apl1/include/variant - headers
New boards would then be added under their board name within the
'variants' directory.
No split has been done with providing different logic yet. This is
purely an organizational change.
Change-Id: Ia3c1f45daee3b9690a448b82edbeec552ee05973
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Due to an accuracy issue on IMON in the IDT PMIC, the reported system
power consumption was higher than the actual consumption. To prevent
this problem, a logic must be implemented in mainboard_init(). This logic
consists of slope and offset as constants for Vcc and Vnn, which need
to be programmed by coreboot. This fix compensates for the accuracy
issue.
Change-Id: I77faf95951d03ac6ce97a6721dba6e8466122a25
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
By storing the FSP-M DRAM configuration parameter in the hwinfo block,
one becomes more flexible in case of a change of the DRAM type.
The configuration data from hwinfo block is a one-to-one representation
of the FSPM_UPD data starting with parameter 'Package' (offset 0x4d) and
ending before parameter 'Ch0_Bit_swizzling' (offset 0x88).
Change-Id: I58c1df0954a436710ecb59487ece07a0832b0de6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This change uses an array pcie_rp_clkreq_pin for accepting CLKREQ#
from mainboards instead of defining a separate property for each root
port. This allows us to use memcpy to copy the entire array into FSP
params as well as new properties for PCIe root ports can be added as
arrays in future CLs.
BUG=b:74633273
BRANCH=reef,coral
Change-Id: Ifa05f1e38fcfd95063ec327712e472cdbd12dbb7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Coverity scan has found an error where a NULL pointer is dereferenced.
The bug would happen if the devicetree does not contain a valid entry
for PCA9538. In this case the code
* if (dev->path.i2c.device == PCA9538_SLAVE_ADR)
would dereference to a NULL pointer.
This patch fixes this issue. Thanks coverity!
Found-by: Coverity (CID 1386126: Null pointer dereferences (REVERSE_INULL))
Change-Id: I75e271d86c16fa3938420c43575ebba910f6a2fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Show mainboard version in the console log so that one can easily see it.
Change-Id: I33bae8b340fce13c0cbe525521828929038b069a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The I/O expander on the mc_bdx1 is used to get the hardware version of
the mainboard. This patch enables the chip driver for the I/O expander.
Change-Id: I98c667fe4dccf0698ab4cb5ede6082f020c70ec6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
For internal measurements this mainboard needs a marking inside the NC
FPGA when coreboot is ready and payload has been loaded.
Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The default setting for I2Cx is 400kHz. On this mainboard there is a
device on I2C0 which requires a lower clock rate to work correctly. For
this reason we set the frequency to 100kHz.
Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard has its own coreboot ready LED. The LED is switched on
via GPIO CNV_RGI_DT.
Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are PCI devices, which are connected to the PCIe
root port via a PCIe-2-PCI bridge. One of the devices only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 4 (Device 14.0).
The following routing is required:
INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA#
Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add GPIO initialization for mc_bdx1 mainboard. Call init_gpios() as
early as possible as FSP will set up things (like hiding PCI devices)
rather early. If connections on the mainboard are dependent on GPIO
settings then FSP can screw things up (e.g. disabling not yet connected
PCI root ports).
Change-Id: I003277cfb871f861900b7fcdc5ec851d4c1c1e6a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/22035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Like happend in commit efd0eb35af
(siemens/mc_apl1: Add delay to wait for legacy devices) add the
feature to mc_bdx1 as it uses the same legacy devices.
Change-Id: I355a53ce7aea70098d7bc08f24dc6a4e43d1d618
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/21933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
IRQ 9 is used for different purpose on this mainboard so move SCI away
to IRQ 10.
Change-Id: I7f055447f5d92bc4696b38e8103a7aebde95d9d3
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There are old legacy onboard devices which are too slow for a coreboot
boot with log level BIOS_ERR. In this case coreboot is so fast that these
devices do not have enough time to become visible on the PCI bus and
this in turn leads to missing resource allocation for this devices. The
most generic way to work around this problem on existing hardware is to
introduce a delay right before the PCI enumeration starts. The needed
delay time depends on the hardware and will therefore be get from
hwinfo.
Change-Id: Ia91babc81e3a347bbc498c3def97b2ea70e10922
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/21518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
APL internal UARTs are not used on this mainboard.
Change-Id: I39118262fc6f37b45785538a3f2d1d31d42cbe86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is one on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I45202937eba11da3bea14fef6ebed70599804335
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Note that all boards incorrectly had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add LPC common code to be shared across Intel platforms.
Also add LPC library functions to be shared across platforms.
Use common LPC code for Apollo Lake soc. Update existing Apollolake
mainboard variants {google,intel,siemens} to use new common
LPC header file.
Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The mc_apl1 mainboard needs to disable the RAPL algorithm for a constant
power management of the processor package. An active RAPL algorithm
leads to negative effects with our real time software.
Change-Id: I09ca56a034fd3896a000e64cac35f12fb507a682
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This mainboard is equipped with DDR3L modules which support ECC. The
BWG says that for activating ECC the FSP-M parameter MemoryDown must be
set to 5.
Change-Id: Idc68df1e2bae2396c9b9788d4a026a75b7d9119b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The OS of this mainboard needs the _PIC method for the selection of the
type of interrupt routing.
Change-Id: Ic82ba1b368aff0030422d9602ebc882247a2191b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20618
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
SDCARD is not used on this mainboard.
Change-Id: I28d23cdb3652bf736b19daf67c7057c396230e24
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Set RX6110SA RTC backup mode to primary cell. This mode reduces the
backup current consumption of the RTC.
Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The used RTC6110SA has issues to enter backup mode when the power supply
decreases too slow when the mainboard is turned off. Switch to backup
mode "primary cell" to make sure backup mode will be entered correctly
on power-off. In addition set IOCUTEN to minimize the backup current
consumption of the RTC.
Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There are up to two on-board PCI devices where bus master has to be
enabled in PCI config space. As there is no need for a complete PCI
driver for these devices just set the bus master bit in
mainboard_final().
In a perfect world that would be the task of the runtime driver which
unfortunately don't do that.
Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It does not work to enable the LPC range in the function
mainboard_init() because the LPC bus driver closes the range during PCI
enumeration again. For this reason, enabling decoding of the address
range for COM 3 will be done at a later point in time -
mainboard_final().
Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
With enabled XDCI support we are not able to use USB port 0 over XHCI
driver. For this reason, we disable XDCI into devicetree.cb.
Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
To unify the hwinfo handling along all Siemens MC boards the hwinfo
files have to be removed from the mainboard directory. They will be added
to cbfs in site-local/Makefile.inc.
Change-Id: Ia3dcb2e0118527b37aed872740273c4fa7004aef
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The prior used RTC PCF8523 is replaced with RX6110SA on this mainboard.
Switch to the new RTC in Kconfig and adapt devicetree to the new chip.
Change-Id: I7c4911191cae254900f9a958da42ecd18497484c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Program eMMC DLL settings for mc_apl1 mainboard, after that system can
boot up with eMMC successfully.
Change-Id: I3d60f66ec5c7e09540ccda59f244aac6f78bf954
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The mainboard siemens/mc_apl1 uses an external I/O port for console
output. For this reason we need to activate the 8250 LPC UART.
Change-Id: Ib5616a116aec6135191bdce95f9f9566ce13d6f1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This mainboard contains an external RTC chip RX6110 SA. Enable usage of
this chip and set some initialization values to device tree.
Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
- set GPIO_183 to high level for enabling the power of SD card
- delete all GPIOs for JTAG interface because they lead to problems with
Lauterbach debug hardware
Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
soc/i2c.h does not need to be included in this compilation unit.
Change-Id: Ife11642d2e69af7235c93fc54bba38853b046169
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This needs some extra headers in amdk8/raminit.c that were otherwise
provided by that file.
Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19360
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
For this debug.c needs to be linked too.
Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is needed if one wants to use the header more than once.
Change-Id: I375d08465b6c64cd91e7563e3917764507d779ba
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19029
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This mainboard uses a LVDS connection for LCD panels. Apollo Lake SoC
provides a display controller with three independent pipes (1x eDP and
2x DP/HDMI). PTN3460 is an embedded DisplayPort to LVDS bridge device
that enables connectivity between an eDP source and LVDS display panel
(http://www.nxp.com/documents/data_sheet/PTN3460.pdf).
The bridge contains an On-chip Extended Display Identification Data
(EDIT) emulation for EDIT data structures.
This patch sets up PTN3460 to be used with the appropriate LCD panel.
Change-Id: Ib8fa79bb608f1842f26c1af3d7bf4bb0513fa94d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adjust gpio settings according to the hardware layout.
Change-Id: I2f440e863c2e6f59298c500ac5aefa3b7386bcdf
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18995
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Currently, it’s impossible for the user to select `NO_POST`, for boards
selecting `CONSOLE_POST` in their config.
```
warning: (BOARD_SPECIFIC_OPTIONS) selects CONSOLE_POST which has unmet
direct dependencies (VENDOR_SIEMENS && BOARD_SIEMENS_MC_BDX1 || !NO_POST)
```
This is currently done for Intel Camelback Mountain and Siemens MC-BDX1.
Selecting the option `CONSOLE_POST` in board specific configuration is
not a good idea, as this should be user configurable over Kconfig, and
also the tree-wide defaults should be the same for these options.
Kconfig is different, as commit 97535558f1 (mainboard/{google,intel}:
Change config option selection) only touch the Intel board.
Change-Id: I91c1e0cb92ed218b6bbc7c33759b91f748cf6f51
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18878
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch make some general adaptations in relation to commit 6a489237
(mainboard/intel/leafhill: Clean up).
- add necessary defaults to Kconfig
- remove irrelevant entries from FMD file
- include romstage file for better understanding
Change-Id: I190d648a7ffeca11acc6560db85ff03c78e85b21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18808
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard uses two i210 Ethernet controller. Therfore we enable the
usage of the i210 driver and have to provide a function to search for a
valid MAC address for all i210 devices by using Siemens hwilib.
Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18380
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This commit makes a basic adjustment for GPIOs, device tree, flash map and
MRC settings. With these basic settings the mainboard boots into
Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow.
Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18292
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with minimum changes. Special adaptations for MC APL1
mainboard will follow in separate commits.
Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18272
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
Baytrail SoC has a bug where in some cases the DisplayPort can hang
leading to a non-working display (it just stays black). To avoid this
hang, a patch was introduced in 02/2016
(1c3b1112fa - fsp_baytrail: Fix a possible hanging DisplayPort)
but per default not switched on so that each
mainboard can decide if it wants to use this patch or not.
Recently a new case of this bug was reported by Benoit Sansoni
(benoit.sansoni@kontron.com) and he requested to enable this fix per
default as it costs him a lot of time to find the cause and even the
already available fix in coreboot. To avoid this effort for someone
else in the future we can enable this fix per default as no negative
side effects are known and it is now tested at Siemens and at
Kontron on different mainboards with success.
As the goal is to enable this code permanently the config switch is not
longer needed and is removed.
Change-Id: I15bd682218d0dc887945cc91ee3e5488945a6355
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/18109
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do not abort the initialization of PTN3460 if HW-ID could not be
retrieved and just assume that the HW-ID does not match 7.9.2.0.
In this case PTN3460 will be setup to a working condition even
if this field is missing.
This makes this driver more robust with faulty blocks.
Change-Id: I301fb165a7924768e44182d92be820294beb0280
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/17671
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Due to some LVDS cable constraints even and odd lanes needs
to be swapped on certain hardware. The hardware ID will be used to
distinguish between these two cases. The swapping itself will be done by
PTN3460, which is configurable for that.
Change-Id: I339b2321a8ed1bc3bbf10aa8e50eb598b14b15fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/17576
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
I guess it was dropped because its concept was misunderstood. The idea
is to always have it set to `Yes` in the cmos.default. Users can then
ack the loading of the defaults by setting it to `No`. If the defaults
ever get loaded again, they'll be notified by the default `Yes`.
Change-Id: I1aa6d75bd5aa153c7b11a6b74564272eaa7cc523
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17355
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Due to different LCD panel requirements the delay between LVDS becomes
active and the backlight is switched on needs to be increased to 500 ms.
Change-Id: I09029624469aef412141c7b46224d48557ba4af1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16875
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Since this mainboard provides 4 COM ports on LPC, enable decoding of
the corresponding addresses using the generic LPC decode registers.
Change-Id: I0e93d40dca01d55f3567a18c7ec02269e3bec466
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16535
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Almost all of the places where we have the degree symbol '°', it's
encoded as 0xc2 0xb0 (utf-8 encoding). There are a few places where it
is encoded as just a high ascii byte: 0xb0. Editors that support the
high ascii 0xb0 seem to support the utf-8 0xc2 0xb0 encoding as well,
but the opposite does not seem to be true.
Change the high-ascii degree symbols to utf-8 encoding.
Change-Id: I3d06289b802f45e938dc72b4c437fca56235b62b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15978
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard contains an external RTC chip PCF8523. Enable usage of
this chip and add some initialization values to device tree.
Change-Id: I25c0a017899ee904f3aa02bdc7dcaf61dee67e3a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15642
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
IRQ 9 is used for different purpose on this board so move
SCI away to IRQ10.
Change-Id: I107bfb5ec8cd05f844ee75550779be7746e77a88
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15563
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Since SPI controller opcode registers are locked by FSP, they need to be
initialized to a known good state before ReadyToBoot event and after
every SPI flash access (e.g. for MRC cache) has been finished in order
to enable the OS to use SPI controller without constraints.
Change-Id: I0a66344cd44e036c3999ae98d539072299cf5112
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15547
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Enable the usage of DRIVER_INTEL_I210 and provide a function to search
for a valid MAC address for all i210 devices using hwilib.
Change-Id: Ic0f4f1579364cf5b0111334a05a8a0926785318b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15517
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The function mainboard_get_mac_address() is used to get a MAC address
for a given i210 PCI device. Instead of passing pure numbers for PCI
bus, device and function pass the device pointer to this function. In
this way the function can retrieve the needed values itself as well as
have the pointer to the device tree so that PCI path can be evaluated
there.
Change-Id: I2335d995651baa5e23a0448f5f32310dcd394f9b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15516
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The LCD panel type is read using 4 GPIOs. Of these 16 possible
combinations only 5 are supported right now. If the GPIO setting encodes
an unsupported panel type, there will be no matching hwinfo.hex in cbfs.
Therefore it makes no sense to try to initialize the DisplayPort-2-LVDS
converter. Leave the function instead in this case.
Change-Id: If8c67a3f5be762758d516c4939dd1de4ff1c8ba5
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14743
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The verb *set up* is written with a space [1]. So correct that in the
function descriptions.
[1] http://www.merriam-webster.com/dictionary/set%20up
Change-Id: Icf5aa7eca2c379fdf7ff1935d71efc347f5ce6fa
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/14701
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Assigning the value `1` to `status` in the default branch of the switch
statement is not needed, as the stored value is overwritten before it
can be used.
Change-Id: I532b0e217ff4ed315cd30b08d339c755c6df7539
Found-by: Coverity, CID 1355008: Code maintainability issues (UNUSED_VALUE))
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/14699
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add new mainboard for MC BDX1 board which is based on Intel Camelback
Mountain. This mainboard is an industry type board and has several
Ethernet interfaces among with two USB3.0 connectors. It uses 24V DC
power supply and has its own form factor which does not match any
standard.
This commit adds the new mainboard and prepares the Kconfig
environment so that this board can be selected and generated.
Although the generated image can boot into Linux and DOS,
not all functions are implemented yet.
Forthcoming commits will add more functionality.
Change-Id: I29011cfd3b0d13bcf163223f657e02f69978e39a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14516
Tested-by: build bot (Jenkins)
Reviewed-by: York Yang <york.yang@intel.com>
Switch all types to uint8_t and the like instead of u8.
Change-Id: Ia12c4ee9e21e2d3166c2f895c819357fa2ed9a94
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14515
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use hwilib in vendorcode/siemens/hwilib to get fields from hwinfo
instead of having mainboard specific hwinfo code.
This patch does not change the functional behavior in any way.
Change-Id: Idb226a82a08b1b753f654c5cde106236e72f33c3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14506
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The used Baytrail-M SoC on TCU3 tend to have issues
with DisplayPort if the graphic power gate is not set up
in coreboot. To avoid this error, use the graphic init
code on this board.
Change-Id: I973bbaa7d86c1ede1f2884b3a08ccb31f7d85087
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/13774
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
- Add CONFIG_ prefix to two symbols.
- Remove the use of the third symbol as it will never be matched.
Change-Id: Ifa7f6884001cb05fb8397f193c4b08a0161f498c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13539
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use CBFS_AUTOGEN_ATTRIBUTES for mc_tcu3 to enable position
and alignment attributes in cbfs.
Change-Id: I6c39bb02ab641d7e22e20e77a72a577f159549dd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/13123
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The usage of the pin has changed and therefore this pin needs
to be set up as output and drive low initially.
Change-Id: Ie3eb9cc703f7f73d59fad52ea9e514997d84606a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/12754
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is to match the layout of the non-fsp baytrail to make comparisons
easier and possibly remove duplicate files.
Change-Id: I9a94842d724ab3826de711d398227e7bdc1045ff
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-on: https://review.coreboot.org/12686
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The SB600 code had the base address of the HPET hardcoded throughout.
It looks like the plan was to have it be updated in ACPI if needed,
but this wasn't ever implemented. The variable names being used to
do this update were the same, causing an IASL warning. Because of
this, the operation to update the HPET address actually did nothing.
This was fine, because it didn't actually need to be updated.
- Replace all that code with a #define.
- Add and update some comments in the same area.
Fixes IASL warning:
dsdt.aml 1505: Store(HPBA, HPBA)
Warning 3023 - ^ Duplicate value in list (Source is the
same as Target)
Change-Id: I9ba5fe226a4a464e0045ce7d3406898760df5e5a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12705
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
The newer versions of IASL are unhappy when an operator
has the same object as both source and destination.
The warning can be completely disabled with a command
line argument, but in general, I'd really rather not
just disable warnings.
The bits in this register are write 1 to clear, so reading and
writing the same register is what we want to do. Instead, store
it in a temporary register then write it in a second operation.
Fixes warning:
dsdt.aml 1396: Store(PWST, PWST)
Warning 3023 - ^ Duplicate value in list
(Source is the same as Target)
Change-Id: I52d73d4431db237be83016d67cd397f31b53d9c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Devices that have their interrupt routing set to A, A, A, A don't get
any interrupt values assigned because that series evaluates to 0. The
code that sets the interrupt values checks to make sure a value is set
by verifying that it's not 0. On Bay Trail, these are all
single-function graphics devices, so by changing one of the unused
interrupt lines from A to any other value, it assigns the values
correctly.
This issue did not affect ACPI interrupt routing.
This is just a workaround, and the root issue still needs to be fixed.
Change-Id: I78866e3e0079435037e457a4fb04979254b56ee2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12629
Tested-by: build bot (Jenkins)
Reviewed-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Clear the precomputed checksums in hwinfo as they
will be updated in manufacturing process.
Change-Id: I952ca8f1ca32831c4b296de633c0d58da111ccba
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: http://review.coreboot.org/12475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The obsolete and removed getpir utility remarked in its output that the
data is autogenerated. The tool was removed because it wasn't very
reliable, so there's no need to point that anymore.
Change-Id: I5d624931ba7872b1fefa8fa3c270ae7367e069fa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12354
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Remove dummy data from hwinfo.hex as it is not needed
anymore in the system.
Change-Id: I4f328a4ef61741039eb2c030e23fea33f539c2bb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: http://review.coreboot.org/11763
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Since microcode was moved to 3rdparty/blobs, we need to select
USE_BLOBS in Kconfig to get the submodule 3rdparty/blobs automaticaly.
Change-Id: I25e574fd90b830448cacccd16d01a5a2dbc8517d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: http://review.coreboot.org/11764
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The reason for hardcoding the position of the MRC cache was to satisfy
the alignment to the erase size of the flash chip. Hardcoding is no
longer needed, as we can specify alignment directly. In the long term,
the MRC cache will have to move to FMAP, but for now, we reduce
fragmentation in CBFS.
Note that soc/intel/common hardcoding of mrc.cache is not removed, as
the mrc cache implementation there does not use CBFS to find the cache
region, and needs a hardcoded address.
Change-Id: I5b9fc1ba58bb484c7b5f687368172d9ebe625bfd
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Update hwinfo.hex (add dummy data and update checksums).
2. Delete version.hex from mainboard directory. It can be added
in site-local if needed.
Change-Id: I7af9c4a5f606b96177a8ed4e3edf52535f2f1ec7
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: http://review.coreboot.org/11484
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
These are all Kconfig symbols that have been removed or renamed.
USE_PRINTK_IN_CAR was removed in commit 8c4f31b3
Drop the USE_PRINTK_IN_CAR option. It's a bogus decision...
DYNAMIC_CBMEM was removed in commit e2b0affd
Remove Kconfig variable that has no effect
MAINBOARD_HAS_BOOTBLOCK_INIT was removed in commit 342535cc
Remove Kconfig variable that has no effect
CACHE_ROM was removed in commit 4337020b
Remove CACHE_ROM.
SMM_MODULES was removed in commit 44cbe10f
smm: Merge configs SMM_MODULES and SMM_TSEG
INCLUDE_MICROCODE_IN_BUILD was removed in commit eb73a218
soc/fsp_baytrail: Fix use of microcode-related Kconfig variables
CAR_MIGRATION was removed in commit cbf5bdfe
CBMEM: Always select CAR_MIGRATION
REQUIRES_BLOB was removed in commit 70c85eab
build system: Retire REQUIRES_BLOB
CPU_MICROCODE_IN_CBFS was renamed to SUPPORT_CPU_UCODE_IN_CBFS in commit
66e0c4c8 - cpu: Rename CPU_MICROCODE_IN_CBFS to SUPPORT_CPU_UCODE_IN_CBFS
CONSOLE_SERIAL_UART was renamed to CONSOLE_SERIAL in commit afa7b13b
uart: Redefine Kconfig options
CONSOLE_SERIAL8250MEM was renamed to DRIVERS_UART_8250MEM in commit
afa7b13b - uart: Redefine Kconfig options
Change-Id: I8952ca8c53ac2e6cec5f9c77d2f413f086bfab9d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10766
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
- Add the common/firmware subdir to the baytrail & fsp_baytrail
makefiles and remove the code it replaces.
- Update baytrail & fsp_baytrail Kconfigs to use the common code.
- Update the IFD Kconfig help and prompts for the TXE vs ME.
- Whittle away at the CBFS_SIZE defaults. All the fsp_baytrail
platforms have their own defaults.
Change-Id: I96a9d4acd6578225698dba28d132d203b8fb71a0
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10647
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Because of a misunderstanding of how Kconfig files are parsed, the
OVERRIDE_MRC_CACHE_LOC symbol was added to make sure that the value
was correctly set. This is not needed unless for some reason the
Kconfig parser is suddenly rewritten to parse everything differently.
At some point, the value in the FSP's Kconfig file was updated to
OVERRIDE_CACHE_CACHE_LOC, while the entries in the mainboard
Kconfig files were not updated. This resulted in the default values
not getting set correctly by default on the FSP Bay Trail boards.
This removes the whole bunch of incorrect and unnecessary symbols and
just sets the default for the MRC cache location directly.
Change-Id: I1cec758576866b7e0677272b8309bfde8d4a1ee4
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10611
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I3fc8e0339fa46fe92cc39f7afa896ffd38c26c8d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9597
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If SB_HT_CHAIN_ON_BUS0 is selected, HyperTransport chain for System Bus
is the first to scan and it will be assigned with bus number 0.
If HT_CHAIN_DISTRIBUTE is selected, each link will reserve a fixed range
of bus numbers instead of assigning consecutive numbers across all the links.
All fam10 have SB_HT_CHAIN_ON_BUS0 selected under northbridge.
Follow-up can easily drop this if we find this is dictated by architecture.
Change-Id: I8deddcb4c3fd679b6b27e2879d9dba3895c4dd6f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8366
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
A new CBFS API is introduced to allow making CBFS access
easier for providing multiple CBFS sources. That is achieved
by decoupling the cbfs source from a CBFS file. A CBFS
source is described by a descriptor. It contains the necessary
properties for walking a CBFS to locate a file. The CBFS
file is then decoupled from the CBFS descriptor in that it's
no longer needed to access the contents of the file.
All of this is accomplished using the regions infrastructure
by repsenting CBFS sources and files as region_devices. Because
region_devices can be chained together forming subregions this
allows one to decouple a CBFS source from a file. This also allows
one to provide CBFS files that came from other sources for
payload and/or stage loading.
The program loading takes advantage of those very properties
by allowing multiple sources for locating a program. Because of
this we can reduce the overhead of loading programs because
it's all done in the common code paths. Only locating the
program is per source.
Change-Id: I339b84fce95f03d1dbb63a0f54a26be5eb07f7c8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9134
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
