With USBDEBUG selected, the file is built for both romstage and
ramstage. For the ramstage build, we need to explicitly use the
simple PCI config operations without devicetree.
Change-Id: I2de8d9c77bb458ba797c3aac9e2cd0d653e06684
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3437
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This patch sets a bit in the Yangtze southbridge to enable
the extra protocol necessary to handle port multiplier chips.
This has been turned on during most of Kabini development
without any notable impact. Olive Hill has an optional daughter
board that incorporates Silicon Image Steel Vines chips. This
change has been tested with and without the daughter board. This
change can be regression tested using any Hudson-based motherboard,
although it has no impact on boards with discreet Hudson/Bolton
southbridges.
This was tested for impact on SATA performance in the absence of
a port multiplier using the IOZone benchmarks within the Phoronix
Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were
connected to the ports on Olive Hill without using the port
multiplier card. The test results contained more run-to-run
variation within the same configuration than was seen in the
aggregate results comparing the interface with and without the
port multiplier protocol additions. In other words, the test
had less accuracy than the impact caused by turning on port
multiplier support.
Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3808
Tested-by: build bot (Jenkins)
Yangtze uses Hudson AGESA wrapper code but has some changes.
The changes are necessary and have no effects on Hudson.
Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3812
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Directory intel/common must be conditionally added in the list
of source directories, as the parent directory southbridge/intel
is unconditionally added even for boards without such device.
Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3827
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Split the Parmer, Family 15tn, and Hudson DSDT into groups. This splits
the DSDT table into includable ASL files which carry details specific
to the Family 15tn APU, the Parmer platform, and the Hudson FCH. The
dsdt.asl file in the mainboard directory contains only #include
references to the appropriate files.
Initially, this split was done by moving each piece of functionality
into its own file (e.g. IRQ routing and mapping, processor tree, sleep
states and sleep methods, etc.) and those pieces were #included in
dsdt.asl to ensure an exact match (via acpidump/acpixtract/iasl -d)
with the extant version of the table. Once the new tables were found
to exactly match the existing tables, the pieces were rearranged into
reasonable groups (e.g. fch.asl, northbridge.asl, pci_int.asl, etc.).
Some include files have no content but are left as a template for
other platforms and as placeholders for completing the ACPI
implementation for Parmer (e.g. thermal.asl, superio.asl, ide.asl,
sata.asl, etc.).
Change-Id: I098b0c5ca27629da9bc1cff1e6ba9fa6703e2710
Signed-off-by: Steve Goodrich <steve.goodrich@se-eng.com>
Reviewed-on: http://review.coreboot.org/3629
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Routes IRQs for USB device, SPI1, MOTOR, HD audio, CAN bus.
Change-Id: I995a5c6d3ed6a7dca4f0d21545c928132ccbbc21
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3725
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Without that fix, and with CONFIG_SMM_TSEG, we have:
src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep':
src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1
The fix is modelled after src/cpu/x86/smm/smihandler.c which
ifdefs smi_release_lock().
Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3281
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This mistake was spoted by comparison with the
src/southbridge/intel/bd82x6x/smihandler.c file.
Change-Id: I1516f0131d524bd7d001e6780e9a45402d1814d1
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3303
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an option to mark all SPI regions write protected on each S3 resume.
We were used to lock the SPI interface in the payload which isn't run on
the resume path. So we have to do it here.
For the write protection to be effective, all write opcodes in the
opmenu have to be marked correctly (as write operations) and the whole
SPI interface has to be locked. Both is already done.
Change-Id: I5c268ae8850642f5e82f18c28c71cf1ae248dbff
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3594
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All the additional work that needs to be done in EHCI BAR relocation
is independent of the hardware platform and was functionally identical
in all the copies removed.
When USBDEBUG is not selected, PCI EHCI controllers use standard
pci_dev_read_resources() call.
With USBDEBUG selected, PCI EHCI controller's device_operations
.read_resources is replaced with pci_ehci_read_resources() call,
which in turn will replace the device_operations .set_resources call.
The replacement for .set_resources reconfigures usbdebug driver side,
and calls the original .set_resources to configure hardware side.
Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3412
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch is based on 'AMD S3: Program the flash in a bigger data packet'[1]
Some AMD south bridge can write bigger data when saving S3 info.
In this patch, I use config 'AMD_SB_SPI_TX_LEN' to contral data size.
AMD_SB_SPI_TX_LEN is defined in 'src/southbridge/amd/Kconfig'
and then can be overridden in the Kconfig for specific
southbridges that support larger size.
I have tested on AMD Parmer and Thatcher. We will release a new board
whose south bridge can transfer more than 4 bytes each time.
[1] http://review.coreboot.org/#/c/2306/
Change-Id: Id984955d46eae487e39d45979f1a90054aa9f54b
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3413
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change inserts a type cast to eliminate a compiler warning.
Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3541
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The xHCI controller's MMIO space has a length of 64KiB not 4KiB.
Therefore, setting the xHCI BAR to 0xe8001000 worked the same like
setting it to 0xe8000000, as bit12 is reserved and ignored. This again
interfered with the MMIO space of the first EHCI controller and broke
S3 resume on Ivy Bridge.
AFAIK, the MRC ignores the setting of the xHCI BAR, anyway. So just drop
these lines.
Change-Id: I8af9c2ba34133f15636a9056fc8880b3b6ab95e0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3521
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Current build configuration always wants to include an Intel Management
Engine firmware (me.bin) on Sandy Bridge systems. However, we can have
a working coreboot without it, as long as the factory delivered ME
firmware is kept untouched in the flash ROM. So let the user decide if
a ME firmware will be included in the build.
Change-Id: I9a1cc29d4940ba22355eb9e653606e436f07e04c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3522
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
On newer Intel systems, the flash ROM is shared between the host
processor (BIOS), it's Management Engine (ME) and an integrated ethernet
controller (GbE). The layout of the flash ROM (and other information) is
kept in the so called Intel Firmware Descriptor (IFD). If we only want
to build coreboot to update the BIOS section, all we need is the flash
layout.
This patch adds the option to specify the flash layout in the
mainboard's Kconfig, and thus, to build without the real IFD. However,
with such a build, one has to make sure that the IFD section on the
flash ROM won't be written over (nor any other section that hasn't been
included by coreboot). A patch to write selected sections of a flash ROM
with IFD has been sent to the flashrom mailing list [1].
[1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html
Change-Id: Ia23e439a00a197fb54852263f8e206f16c3e8851
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3524
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
LynxPoint LP has only EHCI controller #1.
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: I95c59fb9d5f09afd152872e9bc0418dc67e4aeb2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3472
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: Ib6f7cfac5acf3f8170508547d1584af90273e8c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3471
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Upgrade the ICH7 bootblock to store an initial timestamp like we do it
since Sandy Brigde. I've checked the datasheets for the used scratchpad
registers and grepped for their usage. I'm pretty sure that they aren't
used on any ICH7 based board (for anything before the usual S3-resume
indication).
Change-Id: I28a9b90d3e6f6401a8114ecd240554a5dddc0eb5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3498
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
To have USB 3.0 support the XHCI controller needs to be enabled
and the xhci.bin firmware needs to be added to CBFS.
Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3464
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
They were hard-coded to be copied from 3rdparty/ which isn't always
the right choice.
Since the defaults stay the same, this should be compatible.
Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3453
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The original lines had contradicting comment and code.
This change follows the code and sets MASTER bit too.
Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3466
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This patch provides the correct SD controller timings for
the Family16 device. It also will remove the SD controller
from PCI space when device 0:14.7 is set to off in devicetree.
This was tested on a AMD Parmer board and a AMD G-series SOC
reference board. The settings were found in the AMD
Hudson2 RRG and family16 BKGD.
Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3348
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In case with EARLY_CONSOLE, this printk is called before any other
console is configured to transmit data. This outputs garbage on
CONSOLE_SERIAL as baudrate is not yet programmed.
For case without EARLY_CONSOLE, the order in which different console
drivers initialize is obscure. Might sometimes work properly.
Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3384
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Setting IRQ delivery to FSB got lost in the rebase process
for commit e6143531.
I captured following error on dmesg and this patch fixes it for
i82801dx.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... works.
Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3371
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to
GPIO0.
Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3436
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the
file `usb_debug.c` is added twice to the build.
This was introduced in
commit 4063ede3fb
Author: Ronald G. Minnich <rminnich@google.com>
Date: Mon Feb 4 20:31:51 2013 -0800
bd82x6x: Fix compiling with USB debug port support
Reviewed-on: http://review.coreboot.org/2784
but was unneeded because it had been already added in
the following commit.
commit 4141993536
Author: Sven Schnelle <svens@stackframe.org>
Date: Sat Jul 28 08:52:44 2012 +0200
bd82x6x: Fix CONFIG_USBDEBUG
Reviewed-on: http://review.coreboot.org/1376
Therefore basically revert that hunk.
There is no policy on how to order these additions, so leave
it to a possible separate commit, unifying this.
Kyösti Mälkki suspects that these additions were meant for
the Intel Lynx Point [1].
[1] http://review.coreboot.org/#/c/3424/
Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3425
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix obvious mistake in cycle that displays GPI status
I hope i found all duplicates of it.
Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3435
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a common implementation of SMBus functionality for early chipsets. Note
however, that existing via chipsets are not ported to this code. Porting
will require hardware testing to make sure everything is fine.
This code is used in the VIA VX900 branch.
Change-Id: If5ad8cd0942ac02d358a0139967e7d85d395660f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: Ica3afbf8277cb025251da7af181f8de0d0036b45
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3389
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There is no need to use everywhere BIOS_ERR.
Change-Id: If33d72919109244a7c3bd96674a4e386c8d1a19e
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3307
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too. Define
`ACPI_EN` in the header file `pch.h`.
As commented by Aaron Durbin, a separate `pch_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I6f2559f1d134590f781bd2cb325a9560512285dc
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3182
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too. Define
`ACPI_EN` in the header file `pch.h`.
As commented by Aaron Durbin, a separate `pch_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I4478b1902d09061ca1db8eab6b71fef388c7a74c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3183
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Apparently the files `smbus.{h,c}`, where never used and therefore
build beforehand. Needing one function in them for the ASUS F2A85-M
the build fails as some headers are missing. Including the headers
`stdint.h` and `io.h` fixes the following errors.
[…]
CC southbridge/amd/agesa/hudson/smbus.romstage.o
In file included from src/southbridge/amd/agesa/hudson/smbus.c:23:0:
src/southbridge/amd/agesa/hudson/smbus.h:67:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:67:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:67:55: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:25: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:44: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:56: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:69: error: unknown type name 'u8'
src/southbridge/amd/agesa/hudson/smbus.h:69:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:69:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:55: error: unknown type name 'u8'
src/southbridge/amd/agesa/hudson/smbus.h:71:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:35: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:49: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:59: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:69: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:35: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:49: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:59: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:32: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:44: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:54: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.c: In function 'smbus_delay':
src/southbridge/amd/agesa/hudson/smbus.c:27:2: error: implicit declaration of function 'outb' [-Werror=implicit-function-declaration]
src/southbridge/amd/agesa/hudson/smbus.c:27:2: error: implicit declaration of function 'inb' [-Werror=implicit-function-declaration]
[…]
Probably all the (AMD(?)) `smbus.{h,c}` suffer from this and
should be fixed. Even better, as these function do not differ
between most boards, the file should be moved out from the
specific southbridge directories.
[1] http://qa.coreboot.org/job/coreboot-gerrit/6168/testReport/junit/(root)/board/i386_asus_f2a85_m/
Change-Id: I285101fa06a365da44fa27b688c536e614d57f50
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3202
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Currently the code in the if statement
if (!byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
only gets executed if `byte == 0x0`, that means only in the
default case where RAM voltage is 1.5 Volts. But the RAM voltage
should be changed when configured for the non-default case.
So negate the predicate to alter the RAM voltage for the
non-default cases.
To prevent the build error
OBJCOPY cbfs/fallback/coreboot_ram.elf
coreboot-builds/asus_f2a85-m/generated/crt0.romstage.o: In function `cache_as_ram_main':
/srv/jenkins/.jenkins/jobs/coreboot-gerrit/workspace/src/mainboard/asus/f2a85-m/romstage.c:106: undefined reference to `do_smbus_write_byte'
collect2: error: ld returned 1 exit status
make: *** [coreboot-builds/asus_f2a85-m/cbfs/fallback/romstage_null.debug] Error 1
add `southbridge/amd/agesa/hudson/smbus.c` providing the function
`do_smbus_write_byte` to ROM stage in `Makefile.inc`. That can
actually be used after the needed header files are included in a
previous commit.
Change-Id: I89542479c4cf6d412614bcf4586ea98e097328d6
Reported-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3200
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In the process of streamlining coreboot code and getting
rid of unneeded ifdefs, drop a number of unneeded checks
for the GNU C compiler. This also cleans up x86emu/types.h
significantly by dropping all the duplicate types in there.
Change-Id: I0bf289e149ed02e5170751c101adc335b849a410
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3226
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove local copies of reading and writing I/O APIC registers by
using already available functions.
This change is similar to
commit db4f875a41
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Jan 31 17:24:12 2012 +0200
IOAPIC: Divide setup_ioapic() in two parts.
Reviewed-on: http://review.coreboot.org/300
and
commit e614353194
Author: Kyösti Mälkki <kyosti.malkki@gmail.com>
Date: Tue Feb 26 17:24:41 2013 +0200
Unify setting 82801a/b/c/d IOAPIC ID
Reviewed-on: http://review.coreboot.org/2532
and uses `io_apic_read()` and `io_apic_write()` too.
As commented by Aaron Durbin, a separate `i82801gx_enable_acpi()` is
not needed: “The existing code path *in this file* is about enabling
the io apic.” [1].
[1] http://review.coreboot.org/#/c/3182/4/src/southbridge/intel/lynxpoint/lpc.c
Change-Id: I104a2d9c2898da14d26f8f2992d5a065ad640356
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3181
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit »haswell: Add initial support for Haswell platforms« (76c3700f)
[1] used `1 << 25` to set the I/O APIC ID of 2. Instead using
`2 << 24`, which is the same value, makes it clear, that the
I/O APIC ID is 2.
Commit »Intel Panther Point PCH: Use 2 << 24 to clarify that APIC ID
is 2« (8c937c7e) [2] is used as a template.
[1] http://review.coreboot.org/2616
[2] http://review.coreboot.org/3100
Change-Id: I28f9e90856157b4fdd9a1e781472cc4f51d25ece
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3123
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The "gigabit ethernet controller" (GEC) block was added to AMD
Hudson A55E to integrate ethernet capabilities into an AMD
southbridge.
The GEC is designed to work with B50610 and B50610M gigabit PHY
chips from Broadcom. These parts may not be generally available
in small quantities for embedded development.
The GEC block requires an opaque firmware blob to function. The
GEC blob is controlled by AMD and Broadcom and is not available
from coreboot.org.
This change removes GEC support from AMD Parmer and AMD Thatcher
mainboards since these boards do not have the Broadcom PHY.
AMD has requested that the GEC be hidden for Hudson FCH since
the PHY parts are not generally available. This Kconfig option
can make it appear that this is a viable and supported way to
add Ethernet to an embedded board. It is possible to use the
Hudson GEC block with other PHYs, but this requires development
of a custom GEC blob and a custom Ethernet driver. A custom GEC
blob has been developed for a Micrel PHY, but there is no
accompanying driver.
Change-Id: I7a7bf4d41e453390ecf987c9c45ef2434fc1f1a3
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3127
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Commit 23023a5 correctly enabled the SB800 GPP PCIe ports but didn't
distribute the 4 GPP PCIe lanes amongst the enabled PCIe ports.
This fix was verified by openvoid on a AsRock E350M1 motherboard.
Change-Id: I0116c5f518e0d000be609013446e53da4112f586
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3104
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Commit »Add support for Intel Panther Point PCH« (8e073829) [1] used
`1 << 25` to set the APIC ID of 2. Using `2 << 24`, which is the same
value, instead makes it clear, that the APIC ID is 2.
[1] http://review.coreboot.org/853
Change-Id: I5044dc470120cde2d2cdfc6e9ead17ddb47b6453
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3100
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Fixing warnings introduced by the following patches:
http://review.coreboot.org/#/c/2684/http://review.coreboot.org/#/c/2739/http://review.coreboot.org/#/c/2714/
These patches were meant to fix the dmesg warning about
the OSC method not granting control appropriately. These
patches then introduced warnings during the coreboot build
process which were missed during the patch submission
process. These warnings are below:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 15 2010]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1088 - ^ Not all control paths return a value (_OSC)
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1081 - ^ Reserved method must return a value (Buffer required for _OSC)
ASL Input: dsdt.ramstage.asl - 1724 lines, 34917 bytes, 889 keywords
AML Output: dsdt.ramstage.aml - 10470 bytes, 409 named objects, 480 executable opcodes
Compilation complete. 0 Errors, 2 Warnings, 0 Remarks, 494 Optimizations
This patch gives the following compilation status:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 1 2012]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
ASL Input: dsdt.ramstage.asl - 1732 lines, 33295 bytes, 941 keywords
AML Output: dsdt.ramstage.aml - 10152 bytes, 406 named objects, 535 executable opcodes
Compilation complete. 0 Errors, 0 Warnings, 0 Remarks, 432 Optimizations
The fix is simply adding an Else statement to the If which checks
for the proper UUID. This way, all outcomes will return a full
control package. This patch has no effect on the dmesg output.
Change-Id: I8fa246400310b26679ffa3aa278069d2e9507160
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3052
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reading the paste of code in a message to the mailing list [1],
a typo was spotted and found in one more place.
$ git grep egnoring
src/southbridge/amd/rs780/cmn.c: * egnoring the reversal case
src/southbridge/amd/sr5650/sr5650.c: * egnoring the reversal case
These typos are there since when the code was committed and are
now corrected.
[1] http://www.coreboot.org/pipermail/coreboot/2013-April/075644.html
Change-Id: I55c65f71e4834f209b60d678f0d44bc2f4217099
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3062
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Split the Persimmon DSDT into common code areas.
For example, split the Southbridge specific code into
the Southbridge directory and CPU specific code into
the CPU directory. Also adding the superio.asl file
to the Persimmon DSDT tree. This file is empty for
the moment but will be necessary in the future. I have
also emptied the thermal.asl file in the mainboard
directory because it does not seem to perform as
intended (fan control does not change when it is
brought back into the code base) and it has been
inside a '#if 0' statement for a long time. Removing
it until it is decided that it is actually necessary.
This change was verified in three different ways:
1. Visual comparison of the compiled DSDT pulled from the
Persimmon after booting into Linux using the ACPI tools
acpidump, acpixtract, and iasl. The comparison was done
between the DSDT before and after doing the split work.
This test is somewhat difficult considering the expanse
of the changes. Blocks of code have been moved, and
others changed.
2. Linux logs were dumped before and after the DSDT split.
Logs dumped and compared include dmesg and lspci -tv.
Neither log changed significantly between the two compare
points.
3. The test suite FWTS was run on the Coreboot build both
before and after doing the DSDT split with the command
'sudo fwts -b -P -u'. The flag -b specifies all batch jobs,
-P specifies all power tests, and -u specifies utilities.
Interactive jobs were not run as most of them consist of
laptop checks. Again, there were no significant changes
between the two endpoints.
These tests lead me to believe that there was no change in
the functionality of the ACPI tables apart from what is
known and expected.
This patch is the first of a series of patches to split the DSDT.
The ASRock patch was merged before this one and breaks the ASROCK
E350M1 build (patch 8d80a3fb: http://review.coreboot.org/#/c/3050/).
Please be aware of this dependency when pulling these patches.
Other patches that depend on this patch are
'AMD Fam14: Split out the AMD Fam14 DSDT'
(http://review.coreboot.org/#/c/3051/)
and 'Fam14 DSDT: Also return for unrecognized UUID in _OSC'
(http://review.coreboot.org/#/c/3052/)
Change-Id: I53ff59909cceb30a08e8eab3d59b30b97c802726
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
src/southbridge/intel/lynxpoint/pmutil.c was committed with two
things that needed fixing.
Change-Id: Ib83343a75840aa29847b607b0275971eb8140f12
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3003
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The ACPI NVS region was setup in place and there was a CBMEM
table that pointed to it. In order to be able to use NVS
earlier the CBMEM region is allocated for NVS itself during
the LPC device init and the ACPI tables point to it in CBMEM.
The current cbmem region is renamed to ACPI_GNVS_PTR to
indicate that it is really a pointer to the GNVS and does
not actually contain the GNVS.
Change-Id: I31ace432411c7f825d86ca75c63dd79cd658e891
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds configuration of SerialIO devices in the Lynxpoint-LP
chipset. This includes DMA, I2C, SPI, UART, and SDIO controllers.
There is assorted magic setup necessary for the devices and
while it is similar for each device there are subtle differences
in some register settings.
These devices must be put into "ACPI Mode" in order to take
advantage of S0ix. When in ACPI mode the allocated PCI BARs
must be passed to ACPI so it can be relayed to the OS. When
the devices are in ACPI mode BAR0+BAR1 is saved into ACPI NVS
and then updated and returned when the OS calls _CRS.
Note that is is not entirely complete yet. We need to update
the IASL compiler in our build environment to support ACPI 5.0
in order to be able to pass the FixedDMA entries to the kernel.
There are also no ACPI methods defined yet to do D0->D3->D0
transitions for actually entering/exiting S0ix states.
This is hard to test right now because our kernel does not support
any of these devices in ACPI mode. I was able to build and test
the upstream bleeding-edge branch of the linux-pm git tree. With
that tree I was able to enumerate and load the driver for the
DesignWare I2C driver and attempt to probe the I2C bus -- although
there are no devices attatched.
I am also able to see the resources from ACPI in /proc/iomem get
reserved properly in the kernel.
Change-Id: Ie311addd6a25f3b7edf3388fe68c1cd691a0a500
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This bit offset is incorrect and should only be set based
on another bit in a different register.
Change-Id: I6037534236e3a4a5d15e15011ed9b5040b435eaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2973
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The new enable_pm1() function was doing 2 things wrong:
1. It was doing a RMW of the pm1 register. This means we were
keeping around the enables from the OS during S3 resume. This
is bad in the face of the RTC alarm waking us up because it would
cause an infinite stream of SMIs.
2. The register size of PM1_EN is 16-bits. However, the previous
implementation was accessing it as a 32-bit register.
The PM1 enables should only be set to what we expect to handle in the
firmware before the OS changes to ACPI mode.
Change-Id: Ib1d3caf6c84a1670d9456ed159420c6cb64f555e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2978
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Previously southbridge_smm_init() was provided that did both
the clearing of the SMM state and enabling SMIs. This is
troublesome in how haswell machines bring up the APs. The BSP
enters SMM once to determine if parallel SMM relocation is possible.
If it is possible the BSP releases the APs to do SMM relocation.
Normally, after the APs complete the SMM relocation, the BSP would then
re-enter the relocation handler to relocate its own SMM space.
However, because SMIs were previously enabled it is possible for an SMI
event to occur before the APs are complete or have entered the
relocation handler. This is bad because the BSP will turn off parallel
SMM save state. Additionally, this is a problem because the relocation
handler is not written to handle regular SMIs which can cause an
SMI storm which effectively looks like a hung machine. Correct these
issues by turning on SMIs after all the SMM relocation has occurred.
Change-Id: Id4f07553b110b9664d51d2e670a14e6617591500
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2977
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When calculating the offsets of the various binary blobs within the
coreboot.rom file, we noticed that using mawk as the awk tool instead
of using gawk led to build issues. This was finally traced to the
maximum value of the unsigned long variables within mawk - 0x7fff_ffff.
Because we were doing calculations on values up in the 0xffxxxxxx
range, these numbers would either be turned into floating point values
and printed using scientific notation, or truncated at 0x7fff_ffff.
To fix this, we print the values out as floating point, with no decimal
digits. This works in gawk, mawk, and original-awk and as the testing
below show, seems to be the best way to do this.
printf %u 0xFFFFFFFF | awk '{printf("%.0f %u %d", $1 , $1 , $1 )}'
mawk: 4294967295 2147483647 2147483647
original-awk: 4294967295 2147483648 4294967295
gawk: 4294967295 4294967295 4294967295
The issue of %d not matching gawk and original-awk has been reported
to ubuntu.
In the future, I'd recommend that whenever awk is used, a format is
specified. It doesn't seem that we can count on the representation
being the same between the different versions.
Change-Id: I7b6b821c8ab13ad11f72e674ac726a98e8678710
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2628
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This reclaims space in ACPI NVS by removing unused fields and
adds new fields for SerialIO BARs which will be used to communicate
the allocated resources to ACPI.
Change-Id: I002bf396cf7b495bc5b7e54b741527e507aff716
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2969
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the following commit
commit ee5c111755
Author: Paul Menzel <paulepanter@users.sourceforge.net>
Date: Tue Mar 12 12:41:40 2013 +0100
AMD CIMx SB800: Enable AHCI mode for SATA controller by default
Reviewed-on: http://review.coreboot.org/2661
I forgot to update the help texts to the new SATA mode default. Do
so now.
Additionally note that help texts for `choice` do not seem to be
shown.
Change-Id: I17f401633a2136efca2b21a621482e0724ff9f04
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Make it more similar to i82801d LPC init.
Change-Id: I7b32747ee8012c220c8628994d749999c144b716
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2545
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The haswell patches that verified correctly were not yet submitted,
but verified correctly. However they still used romcc_io.h which was
dropped in another patch earlier today.
With a lot of development happening in parallel, this is
unfortunately nothing that the gerrit 2.6 Rebase If Necessary submit
type could have fixed.
Change-Id: Ifef9ae05b22c408e78d6cff37defd68e4ed91ed9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2876
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This patch implements support for vboot firmware selection. The vboot
support is comprised of the following pieces:
1. vboot_loader.c - this file contains the entry point,
vboot_verify_firmware(), for romstage to call in order to perform
vboot selection. The loader sets up all the data for the wrapper
to use.
2. vboot_wrapper.c - this file contains the implementation calling the vboot
API. It calls VbInit() and VbSelectFirmware() with the data supplied
by the loader.
The vboot wrapper is compiled and linked as an rmodule and placed in
cbfs as 'fallback/vboot'. It's loaded into memory and relocated just
like the way ramstage would be. After being loaded the loader calls into
wrapper. When the wrapper sees that a given piece of firmware has been
selected it parses firmware component information for a predetermined
number of components.
Vboot result information is passed to downstream users by way of the
vboot_handoff structure. This structure lives in cbmem and contains
the shared data, selected firmware, VbInitParams, and parsed firwmare
components.
During ramstage there are only 2 changes:
1. Copy the shared vboot data from vboot_handoff to the chromeos acpi
table.
2. If a firmware selection was made in romstage the boot loader
component is used for the payload.
Noteable Information:
- no vboot path for S3.
- assumes that all RW firmware contains a book keeping header for the
components that comprise the signed firmware area.
- As sanity check there is a limit to the number of firmware components
contained in a signed firmware area. That's so that an errant value
doesn't cause the size calculation to erroneously read memory it
shouldn't.
- RO normal path isn't supported. It's assumed that firmware will always
load the verified RW on all boots but recovery.
- If vboot requests memory to be cleared it is assumed that the boot
loader will take care of that by looking at the out flags in
VbInitParams.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as well
by choosing the RO path.
Change-Id: I45de725c44ee5b766f866692a20881c42ee11fa8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This configures power management registers according to
the 1.2.0 reference code drop. There are many inconsistencies
with the documentation and I tried to note those with ?.
This does not do the same for LynxPoint-H yet.
Change-Id: I9b8f5c24a8b0931075a44398571c9b0d54cce6a6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2819
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This uses the new helper function added earlier.
Change-Id: Icdb5d5c51f70eeb7e39e11062276ceb3eb3d9473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2818
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is updated to handle LynxPoint-H and LynxPoint-LP
and a new wake event is added for the power button.
Boot, suspend/resume, reboot, etc on WTM2
and then check the event log to see if expected events
have been added.
Change-Id: I15cbc3901d81f4fd77cc04de37ff5fa048f9d3e8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2817
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The kernel ACPI was not happy with the Add inside a
ResourceTemplate (or perhaps within the IO declaration)
Instead make a buffer of IO reservations and turn _CRS
into a method that updates the buffer depending on the
chipset type.
This adds an \ISLP() method that checks the chipset LPC
device ID to see if it is -LP or -H.
It also increases the PM base reservation to 256 bytes
and moves both GPIO and PM base to above 0x1000 on -LP
chipsets.
Change-Id: I747b658588a4d8ed15a0134009a7c0d74b3916ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2815
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was put in for debugging and experimentation on i945
and has been copied around since. Drop it from lynxpoint.
Change-Id: I0b53f4e1362cd3ce703625ef2b4988139c48b989
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2814
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are subtle yet significant differences in some of the
registers in the power management region between LynxPoint-H
and LynxPoint-LP.
In order to reduce code that is accessing these registers and
would need special cases this adds a number of helper functions
that can be used in both ramstage and SMM.
This commit just adds the new functions, subsequent commits will
start to use them.
Change-Id: I411da75da519f5b3198a408078cbf3114e426992
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2813
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These base addresses are used in several places and it
is helpful to have one location that is reading it.
Change-Id: Ibf589247f37771f06c18e3e58f92aaf3f0d11271
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2812
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a helper function pch_is_lp() that will return 1 if
the current chipset is of the new "low power" variant used
with Haswell ULT.
Additionally these functions are added to SMM so it can
be used there.
Change-Id: I9acdea2c56076cd8d9627aba66cf0844c56a38fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2811
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to be able to talk to an EC via standard path.
Change-Id: I3fe76882dec9a0596cbc1c844afa2ddb03ed771c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2810
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I'm not sure if I screwed this up originally or the Intel docs changed
(I didn't bother to go back and check). According to ME BWG 1.1.0 the give
up bit is in the host general status #2 register.
Change-Id: Ieaaf524b93e9eb9806173121dda63d0133278c2d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2808
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
So it can get used in both romstage and ramstage.
Change-Id: Ief9eaafdd91df2a7b668de1a9b83aea3af3ff894
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2802
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
SPI accesses can be slow depending on the setup and the access pattern.
The current SPI hardware setup to cache and prefetch. The alternative
cbfs_load_payload() function takes advantage of the caching in the CPU
because the ROM is cached as write protected as well as the SPI's
hardware's caching/prefetching implementation. The CPU will fetch
consecutive aligned cachelines which will hit the ROM as
cacheline-aligned addresses. Once the payload is mirrored into RAM the
segment loading can take place by reading RAM instead of ROM.
With the alternative cbfs_load_payload() the boot time on a baskingridge
board saves ~100ms. This savings is observed using cbmem.py after
performing warm reboots and looking at TS_SELFBOOT_JUMP (99) entries.
This is booting with a depthcharge payload whose payload file fits
within the SMM_DEFAULT_SIZE (0x10000 bytes).
Datapoints with TS_LOAD_PAYLOAD (90) & TS_SELFBOOT_JUMP (99) cbmem entries:
Baseline Alt
-------- --------
90:3,859,310 (473) 90:3,863,647 (454)
99:3,989,578 (130,268) 99:3,888,709 (25,062)
90:3,899,450 (477) 90:3,860,926 (463)
99:4,029,459 (130,008) 99:3,890,583 (29,657)
90:3,834,600 (466) 90:3,890,564 (465)
99:3,964,535 (129,934) 99:3,920,213 (29,649)
Booted baskingridge many times and observed 100ms reduction in
TS_SELFBOOT_JUMP times (time to load payload).
Change-Id: I27b2dec59ecd469a4906b4179b39928e9201db81
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2783
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At some point, compiles with USB Debug port stopped working. This change makes
a trivial reordering in the code and adds two makefile entries to make it build
without errors. It also works on stout.
Build and boot as normal. Works. Enable CONFIG_USB, connect USB debug hardware
to the correct port (on stout, that's the one on the left nearest the back) and
watch for output.
Change-Id: I7fbb7983a19b0872e2d9e4248db8949e72beaaa0
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2784
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Some initialization steps were done twice
- One step was missing for Panther Point HDA
- Added a 1ms delay after reset
- Increased timeout to 1ms for all codec operations
Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Certain SATA devices claim to support SATA 6 Gbps, but in fact have
bugs. For these devices, add a config option to force the SATA link
speed to something other than default.
Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables power management and clock gating on XHCI.
Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
objcopy -B provides symbols of the form _binary_<name>_(start|end|size).
However, the _size variant is an absoult symbol. If one wants to
relocate the smi loading the _size symbol will be relocated which is
wrong since it is suppose to be a fixed size. There is no way to
distinguish symbols that shouldn't be relocated vs ones that can.
Instead use the _start and _end variants to determine the size.
Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The bd82x6x requires some additional setting on S3/S4 entry.
Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the PCH function to SMM for follow-on SMM patches that
require these functions.
Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These enables are hidden behind IOBP for some reason.
Boot to linux with SDIO disabled and see that
the SDIO driver does not load and crash the system.
Change-Id: Icfbfa117e9e57a51d32db7f6366a9d0d790adcf0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2695
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit updates the Lynx Point resource reservations before
the coreboot allocator assigns resources. There is no need to mark
anything as subtractive decode because there are no devices/buses
linked to the LPC device.
The I/O range reservations consists of claiming the first 4KiB
of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode
ranges are checked against the default claimed range. If those
ranges overlap or fall outside of the default range then those
resources are added.
The MMIO range reservations consist of claiming everything from
the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range
register are then conditionally added if they fall outside of
the default MMIO range.
Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2682
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Add device IDs for lynxpoint mobile and LP variants.
- Update the clock gating setup based on BWG
- Update the SATA programming based on BWG
- Add a DEVSLP0 mux config register
Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2649
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
There are enough subtle differences that it is useful to have
a Kconfig entry to differentiate the ULT/LP chipet from the
desktop/mobile versions.
Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2645
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This commit contains a bevy of updates:
- PCI device id is updated to match Lynx Point EDS in the ME driver.
- Allocate the memory to store the consumption of the MBP.
- me_bios_payload structure is now a structure of pointers that point
into the allocated memory.
- The ICC profile structure was updated to correctly reflect the
documentation.
Verfied that output of MBP reading can handle unknown items.
Change-Id: I43cc45e6b797444c105e7c842eb5684e9c104687
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2641
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
According to the 0.8.0 ME BWG this is a new state. It's not very clear
what exactly it entails, but the Basking Ridge CRB was tripping it when
MRC_DEBUG was enabled (presumably because of a DID timeout).
Instead of 0x17 one can now see the proper message for this state.
Change-Id: I5bda1de7d3d957d38a4760a02dcd170ec48782e9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2640
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is no longer tied to a GPIO but has a proper chipset pin.
Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2643
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2618
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The register that controls global reset is named the Power
Mangement Initialization Regiser (PMIR). Update the defines
to reflect the documentation.
Additionally, there is no core well reset control according to the
EDS. There is, however, a CF9 lock field to lock this register down.
Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2619
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME9 requirements have added some registers and changed some
of the MBP state machine. Implement the changes found so far in
the ME9 BWG. There were a couple of reigster renames, but the
majority of th churn in the me.h header file is just introducing
the data structures in the same order as the ME9 BWG.
Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18
Signed-Off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2620
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This follows the new method outlined in the LPT BWG.
It is also very pedantic about its operation so it
is easier to read and compare against the docs and
the reference code implementation.
Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2694
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The current default is IDE mode which is slower compared to AHCI
mode. Therefore use AHCI mode by default.
A similar change was made for AMD Persimmon in commit
»Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1]
but was indirectly reverted by »sb800: Add sata ahci/raid mode
kconfig option« (d4a0e7d0) [2].
[1] http://review.coreboot.org/220
[2] http://review.coreboot.org/225
Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Add PEI updates and ACPI updates for supporting EHCI to XHCI
USB port support.
Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2519
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The power up default for the 14M_25M_48M_OSC switchable clock output ball of
the SB800 chipset is 14 MHz. sb800/bootblock.c changes this to 48 MHz,
which is the correct value for almost all SIOs. However, not for
'smscsuperio' (SMSC SCH311x), which needs the original 14 MHz and is not
configurable for other clock speeds. A wrong SIO clock supply results in
funny RS232 output (wrong bit speed) and non-working PS/2.
We could switch back to 14 MHz in the mainboard's romstage.c, but then the
clock frequency would change twice. The resulting short 48 MHz burst causes
a handful of rubbish characters on RS232 on every boot until the SIO clock
has stabilized again.
This patch skips the SB800 clock switch if the SIO Kconfig requests 14 MHz.
This does not affect any boards currently in the repository (yet).
Change-Id: Icff41fd88dc41c08f3700ab4f786852f04eff2a4
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2454
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
According to both Haswell and the SandyBridge/Ivybridge
BWGs the save state area actually starts at 0x7c00 offset
from 0x8000. Update the em64t101_smm_state_save_area_t
structure and introduce a define for the offset.
Note: I have no idea what eptp is. It's just listed in the
haswell BWG. The offsets should not be changed.
Change-Id: I38d1d1469e30628a83f10b188ab2fe53d5a50e5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Adding RTC init code to the Southbridge initialization
code in 'lpc_init'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same edit made to the CIMX SB800 titled
'AMD/Persimmon: Add RTC init to CIMX SB800' with commit
ID: c4d3d which can be viewed here:
http://review.coreboot.org/#/c/2488/
Change-Id: Iddb7a3cbabe736b511cde03d7dc0a4a0b1c7fd90
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2510
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Adding RTC init code to the Southbridge initialization
code in 'late.c'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This was tested on a Persimmon but will apply to
other mainboards as well.
Change-Id: I9a11bc3f9e3f53c46e7a4d72e62ebb0a4ba1bfe4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2488
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently the size of the volatile storage for S3 reserved in the
image is hardcoded to 32768 bytes. Make that configurable by
introducing the Kconfig 'S3_DATA_SIZE'.
As the storage space is needed for storing non-volatile, volatile and
MTRR data, add a check if the size is big enough.
Change-Id: I9152797cf0045c8da48109a9d760e417717686db
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2383
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For whatever reason tabs got inserted in the license header text.
Remove one occurrence of that with the following command [1].
$ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,'
[1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt
Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2460
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
REQUIRES_BLOB assumes that all blob files come from the 3rdparty directory,
builds failed when all files were configured to point to other sources.
This change modifies the blob mechanism so that cbfs-files can be tagged as
"required" with some specification what is missing.
If the configured files can't be found (wrong path, missing file), the build
system returns a list of descriptions, then aborts.
Change-Id: Icc128e3afcee8acf49bff9409b93af7769db3517
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2418
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marcj303@gmail.com>
S3_DATA_POS defines address where the whole S3 data is stored.
Change-Id: I4155a0821e74a3653caaead890e5fec5677637aa
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2438
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The "system is legacy free" question accidentally escaped
from the hudson Kconfig where it was intended to stay and
went coreboot-wide. This puts it back inside the boundries
of the hudson southbridge where it belongs.
I also commented the endif statements to make it easier to
tell where things belong.
Change-Id: I49f7a5eadb96d40c6101a93bc390e644617a5654
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2179
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Go through southbridge/amd/agesa/hudson, thatcher and parmer
mainboard directories and change all references to sb800 to
reference hudson instead.
This is just cleanup and should make no functional difference.
Change-Id: Icd6a9a08c4bbf5e1aed394362d24c05811ed1fba
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2177
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Add Kconfig option for Legacy free and hook it into the parmer
AGESA initialization as well as the FADT code. This should really
be done inside the southbridge wrapper and not in the mainboard,
but for now the code to attach it to is inside the mainboard.
Update Kconfig for parmer and thatcher to default to legacy free.
Change-Id: Ib899bd02ddc5506caae4aca2c589cc2526638cb8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2157
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update the southbridge/amd/agesa/hudson FADT generation for ACPI
3.0 compliance similar to what was done for cimx/SB800/fadt.c in
commit 9aa4389.
commit 9aa43892e6
Author: Martin Roth <martin@se-eng.com>
Date: Fri May 25 12:23:32 2012 -0600
Update SB800 CIMX FADT
According to the datasheet, PMA_CNT_BLK is no longer available
and PM2_CNT_BLK should not be used. Setup for these has been
removed from the table and .h file.
Change-Id: Ied8eb1f26b4aa364d051ec5f7ed6f482bb440957
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2140
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The cimx/sb800 IMC Firmware location Kconfig option has
a typo which would could set it to the wrong location.
Change-Id: I38016bebd1bfe6ad6d3f1c02cb1960712fbf4ab2
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2120
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
That code will be used to disable the internal GFX card and enable the
external PCIe card.
The following lines from function `rs780_internal_gfx_enable()` are
taken and reversed.
/* Disable external GFX and enable internal GFX. */
l_dword = pci_read_config32(nb_dev, 0x8c);
l_dword &= ~(1<<0);
l_dword |= 1<<1;
pci_write_config32(nb_dev, 0x8c, l_dword);
It has been tested on the M4A785T-M with the following card inside the
PCIe 16x slot:
02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
Change-Id: I7bd412b987fde98c97464175e2c7a384a8f0fb84
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2065
Tested-by: build bot (Jenkins)
If a 3rd party blob option is selected, make sure that it makes the
user select CONFIG_USE_BLOBS as otherwise the build will fail.
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I04429f23137946525c8577dd9c979bd4a0d17cdc
Reviewed-on: http://review.coreboot.org/2080
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since SB800, USB2.0 debug port is dev 0x12, func 2.
Change-Id: Ie0e33cb2f0833b0baeef81323e1a0634242fbe55
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1880
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
We ship it in the 3rdparty repository.
Change-Id: Ida52bc7e813f8468910c4ea7838ebb863c52b88a
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2060
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Add prefix coreboot_ to let make clean find it and delete it.
Change-Id: Ieba9c0e7ca3d2afec311d64159b22746ba5825c4
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2029
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add configuration for AMD's IMC ROM and fan registers for cimx/sb800
platforms.
- Allows user to add the IMC rom to the build and to configure the
location of the "signature" between the allowed positions.
- Allows for no fan control, manual setup of SB800 Fan registers, or
setup of the IMC fan configuration registers.
- Register configuration is done through devicetree.cb. No files need
to be added for new platform configuration.
- Initial setup is for Persimmon, but may be extended to any cimx/sb800
platform.
Change-Id: Ib06408d794988cbb29eed6adbeeadea8b2629bae
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The file generated when the IMC or XHCI binaries are included in the rom
was named $(obj)/hudson_romsig.bin. The problem with this is that it
doesn't get deleted when the user does a make clean.
changing the name to coreboot_hudson_romsig.bin makes this happen.
Change-Id: I19a40042fbf0f7b5633d7b35339c05ed90d3243b
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1978
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
There was already a special case for the SPI base address in
lpc_set_resources for southbridge/amd/cimx/sb800 and
southbridge/amd/agesa/hudson, but it needed to be modified
to keep from killing the IMC rom during initialization. As
soon as the BAR is disabled by setting the new base address,
the IMC dies. The fix is to make sure it's still enabled
when setting the new base address instead of setting the new
address then re-enabling it.
Change the name SPIROM_BASE_ADDRESS to SPIROM_BASE_ADDRESS_REGISTER
to more accurately describe what we're using.
Change-Id: I216d75b722c4332c239d487111a9880eabf59e91
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1975
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The SB800 and Hudson now support adding the IMC ROM which runs from the same
chip as coreboot. When the IMC is running, write or erase commands sent to
the spi bus will fail, and the IMC will die. To fix this, we send a request
to the IMC to stop fetching from the SPI rom while we write to it. This
process (in one form or another) is required for writes to the SPI bus while
the IMC is running.
Because the IMC can take up to 500ms to respond every time we claim the
bus, this patch tries to keep the number of times we need to do that to a
minimum. We only need to claim the bus on writes, and using a counter for
the semaphore allows us to call in once to claim the bus at the beginning
of a number of transactions and it will stay claimed until we release it
at the end of the transactions.
Claim() - takes up to 500ms hit
claim() - no delay
erase()
release()
claim() - no delay
write()
release()
Release()
Change-Id: I4e003c5122a2ed47abce57ab8b92dee6aa4713ed
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1976
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Remove the old, unflexible code for storing S3 data in SPI flash.
Refer to flashrom. Tested on Parmer.
Change-Id: I60a10476befb4afab2b4241f01a988f4a8bb22cd
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1920
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
As we move to supporting other systems we need to get rid of assembly
where we can. The log2 function in src/lib is identical to the assembly
one (tested for all 32-bit signed integers :-) and takes about 10 ns
to run as opposed to 5ns for the non-portable assembly version. While speed
is good, I think we can spare the 15 ns or so we add to boot time
by using the C version only.
Change-Id: Icafa565eae282c85fa5fc01b3bd1f110cd9aaa91
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1928
Tested-by: build bot (Jenkins)
This broke because those components were not yet
committed when the patch to drop the driver class
was made.
Change-Id: I29948223503a6c4b196eafa169c064cd26da1be1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib4401897570f9e4d31c18d05144b5deb6f4523bc
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1873
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for ICH9 southbridge
Change-Id: I70612431101bf48d9dcc96ee1b37d257c9ad2ee2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1690
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
e.g.
-#if CONFIG_LOGICAL_CPUS == 1
+#if CONFIG_LOGICAL_CPUS
This will make it easier to switch over to use the config_enabled()
macro later on.
Change-Id: I0bcf223669318a7b1105534087c7675a74c1dd8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1874
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
hard_reset was indeed consolidated and moved into the southbridge
code a while ago, but the config variable was still kept alife, with
some duplicate code.
Change-Id: I60d4a87de916667f6e89353dfbe1a7b9eca380f7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The search for save state was comparing the entire RAX
value when it needs to just operate on the bottom byte
so it can find the GSMI command in bits 7:0 but not the
extended command code in bits 15:8.
Change-Id: I526c60e6b3732fa3680a17a4bed2a2ef23ccf94f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1774
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of hijacking some random memory addresses to
relay the GNVS pointer to SMM we can use EBX register
during the write to APM_CNT register when the SMI is
triggered.
Change-Id: I79a89512c40353d72ad058cbf2e6a23a696945da
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1766
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is currently used by the ELOG GSMI interface but is a
good way to pass data to SMM so move the current searching code
to a separate function and make it a bit more versatile with the
checks it does to find a match so it can be used in other
situations.
Change-Id: I5b6f92169f77c7707448ec38684cdd53c02fe0a5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM GNVS pointer is normally updated only when the
ACPI tables are created, which does not happen in the
resume path.
In order to restore this pointer it needs to be available
at resume time. The method used to locate it at creation
time cannot be used again as that magic signature is
overwritten with the address itself. So a new CBMEM ID
is added to store the 32bit address so it can be found
again easily.
A new function is defined to save this pointer in CBMEM
which needs to be called when the ACPI tables are created
in each mainboard when write_acpi_tables() is called.
The cpu_index variable had to be renamed due to a conflict
when cpu/cpu.h is added for the smm_setup_structures()
prototype.
Change-Id: Ic764ff54525e12b617c1dd8d6a3e5c4f547c3e6b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For reasons of security and testing we want to be able to
enable/disable ME section locking through a config option.
Change-Id: I341c577cdae86be62c0e3d32bbd6b3333c004a5f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1798
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Right now coreboot's build process produces images that are
not booting on actual hardware because they are smaller than
the actual flash device and also don't have an IFD nor an ME
firmware in them. In order to produce bootable images, you
needed a wrapper script / extra step until now. With this
change, the resulting coreboot.rom is actually bootable.
Change-Id: I82714069fb004d4badc41698747a704bd9fed4da
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1771
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a basic romstage driver that can be used for the
MRC cache code on systems where we do not have the MRC cache
stored in a flash region that is memory mapped.
It uses the hardware sequencing interface to avoid having
to know anything about the flash chip itself.
BUG=chrome-os-partner:15031
BRANCH=stout
TEST=manual: this was tested with debug code added to romstage
that attempted to read the MRC cache at offset 0x3e0000.
SPI READ offset=003e0000 size=64 buffer=ff7fba00
SPI ADDR 0x003e0000
SPI HSFC 0x3f00
SPI READ: 0=4443524d
SPI READ: 1=00000bb0
SPI READ: 2=00008e24
SPI READ: 3=00000000
SPI READ: 4=001c8bbb
SPI READ: 5=0c206466
SPI READ: 6=0a043220
SPI READ: 7=000058b4
SPI READ: 8=00000000
SPI READ: 9=00000000
SPI READ: 10=00100000
SPI READ: 11=00100005
SPI READ: 12=20202025
SPI READ: 13=000e0001
SPI READ: 14=00000000
SPI READ: 15=00000000
Change-Id: I5f78f53111f912ff5dda52bbf90fdc1824b82681
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1777
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Fix handling of 5-byte Fast Read command in the ICH SPI
driver. This fix is ported from the U-boot driver.
- Allow CONFIG_SPI_FLASH_NO_FAST_READ to be overridden by
defining a name for the bool in Kconfig and removing the
forced select in southbridge config
- Fix use of CONFIG_SPI_FLASH_NO_FAST_READ in SPI drivers
to use #if instead of #ifdef
- Relocate flash functions in SMM so they are usable.
This really only needs to happen for read function pointer
since it uses a global function rather than a static one from
the chip, but it is good to ensure the rest are set up
correctly as well.
Change-Id: Ic1bb0764cb111f96dd8a389d83b39fe8f5e72fbd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1775
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Intel PCH can override the ASPM settings via the MPC2 register.
Add a chip override for F0-F7. Mainboards may implement this as
needed.
This also fixes the final PM setup being done too early. It was
being done prior to the PCIe ASPM setup, which happens in the
bridge scan.
Change-Id: Idf2d2374899873fc6b1a2b00abdb683ea9f5bd6b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1796
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Right now the SPI bus is getting set to 20mhz for transactions
initiated with the software sequence interface.
In order to be able to do reasonable fastread/write/erase we
can bump this up to a higher value at boot before it gets
locked at 20mhz.
To do this read out the speed set in the SPI descriptor for
hardware sequencing and apply it to software sequencing.
Change-Id: I79aa2fe7f30f734785d61955ed81329fc654f4a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The chips we are using do not use BE52 (block erase 0x52)
so we can use that opcode menu location to enable fast read.
Change-Id: I18f3e0e5e462b052358654faa0c82103b23a9f61
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And move the pre-hardwaremain post code to 0x79
so it comes before hardwaremain at 0x80.
Emit these codes from ACPI OS resume vector as well
as the finalize step in bd82x6x southbridge.
Change-Id: I7f258998a2f6549016e99b67bc21f7c59d2bcf9e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The sleep type is 5 for S3 and 7 for S5.
Change-Id: I7ffdb3d27b6994ac4a12a343caf4d7abb82fe6ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These bits are used by the IGD OpRegion code
Change-Id: I89a11fc5021d51e0c1675ba56f6a3bc3b79bb8aa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1751
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In order to support Intel's IGD Opregion standard, we need
an additional set of flags shared between firmware, ACPI, SMM, and the
graphics driver.
Change-Id: I1a9b8dff5e5ee8d501b6672bc3bcca39ea65572e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the driver is initialized before the lockdown then it will
fail to work after the lockdown bit is set.
Change-Id: Idc05d33d8d726bf29cb3c9b1b4604522bd64170a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In case tseg_relocate() is called again on a pointer we should not
relocate it again.
Change-Id: Ida1f9c20dc94b448c773b14d8864afe585369119
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We are seeing ME disabled and ME error events on some devices
and this extended info can help with debug.
Also fix a potential issue where if the log does manage to get
completely full it will never try to shrink it because the only
call to shrink the log happens after a successful event write.
Add a check at elog init time to shrink the log size.
Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The handling of write enable was not entirely correct,
the opcode needs to be skipped when the controller is
locked down.
Addresses were not getting set properly for erase commands
which seemed to mostly work when the previous command had
set an address.
Tested by adding events to the event log at runtime on a
freslhy flashed device (with locked down SPI controller)
until the log log shrink happens to ensure it does not hang:
hexdump -C elog.event.kernel_clean
00000000 01 00 00 00 ad de 00 00 00 00
for x in $(seq 1 232); do
cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog
done
mosys eventlog list | tail -6
154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
158 | 2012-09-01 13:54:43 | Log area cleared | 1030
159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that WREN prefix is handled properly ELOG is able to write
when the SPI controller is locked down.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: If6d0dced7cb0f5ca7038b3d758f31b856826d30b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1712
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
The code that attempts to use the opmenu needs to have a special
case for write enable now that it is handled as an atomic prefix
and not as a standalone opcode.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1710
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
This appears to fix an infrequent resume hang on Ivybridge.
Tested on 2 devices with 15k suspend/resume cycles each
Change-Id: I53618bc7966824413f1720a2be3cbd2550e29473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1704
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Every line of text after a 'help' label in a Kconfig
file must have the same whitespace preceding it, otherwise
it's no longer considered help text.
Change-Id: I97093bee72b295b315d78d4c26d7186bf1017fda
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1687
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Unfortunately the reference tool chain was updated
without ever even testing it on an abuild run. This
broke a number of ports.
This change gets coreboot at least compiling again
for all supported systems.
Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1670
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Some 32 bit machines print integer higher than 0x80000000
as negative number.
Change-Id: Ieb512ed2a7499ce7e91e45e4075d4f119780b57d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1547
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Try
sh> printf %d 0x005500AA | LC_ALL=C awk '{printf("%c%c%c%c", \
$1 % 256, $1/256 % 256, $1/65536 % 256, $1/16777216);}' | \
od -Ax -t x
On Linux with gawk, we get
000000 005500aa
000004
On FreeBSD with nongnu-awk, we get
000000 000055aa
000002
In awk, all the numbers are floating point number. So division doesn't
round the result from 0.75 (3/4) to 0.
And, There is a fact that, for the FreeBSD awk,
sh> awk 'BEGIN {printf("%c", 0.75)}';
produces nothing, instead of 0.
Here we need to convert the floating point number to
integer by int(X), which is an awk built-in function, instead of GNU
extension.
Change-Id: I3470d5f13e7ea59a978d5575a54c0d56368dc78d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1529
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
TRACE has redefined warnings in src/southbridge/amd/cimx/sb700/Platform.h,
so we do some changes to remove such warnings.
Change-Id: I24979e08b83434f91a8fa37cd9f16303fa0b298d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1499
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Command expr in some systems only take 32bit as integer, which
value is at 0x7FFFFFFF ~ -0x80000000. Use awk as alternate way to
calculate.
And some system doesnt take hex value in Makefile, even in awk instruction.
Change-Id: Ie35d6a5b96eea4192bd9cab857af4d4dcb37b9ed
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1527
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Forgot to change the code back after debugging.
Change-Id: Iaf58d65c14d53ca77958080faf6ab85d60992226
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1491
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Prior to this change the setting would be zeroes and
would cause a BSOD in 64 bit versions of Windows.
Change-Id: I2d422ef9667457af53f9fd055799e489ed2b25db
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1475
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Maybe sooner or later python is not a default tools to build coreboot.
Most of the work is done by awk now. GNU extension of gawk is not used, isn't?
echo, expr, printf, cat, awk, test, mv are the external tools.
If XHCI, IMC or GEC firmware is not available and not defined, this script can skip
integrating them.
Change-Id: I9944b22b0b755672a46d472c355d138abafd6393
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1417
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
The names were set at various times during development, but
the way the code works, you might end up with the wrong name
being displayed in the logs. Instead of doing magic, just
display both names for each component
Change-Id: I1f8ce44d156442f5f7d717e1a2b47ed1218d4527
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1413
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Move beep commands to board-specific area as they need to be different for
different codecs.
Change-Id: I2a1ac938c49827cc816a95df10793a7e234942bf
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: http://review.coreboot.org/1410
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use IORESOURCE_RESERVE to exclude the region from system RAM table.
Change-Id: I61b51022165e1304a41554f67af75b3089d892af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1393
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Apply the change
http://review.coreboot.org/1390
to all the AMD southbridge.
Change-Id: I8e94014f8883a0408b68355d9aa33aea4373881f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1406
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In accordance to PCH EDS 14.1.35.1
Change-Id: I2e6cec6d4f49f404e33a171a8fbd6e4880327896
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1411
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Parmer and thather hang at windows 7 booting process. Setting the
valid date in CMOS can fix that.
Change-Id: I5e427cfb42430ebebdb4c1e48bd25860c0fec45f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The code in rs690 or rs780 is always used with K8 or AMDFAM10
northbridge. Without GFXUMA, both of these set the same static value
indirectly using the variable uma_memory_base.
Make the register setting with immediate value, to remove the obscure
use of variable uma_memory_base.
Change-Id: I5354684457a76e73013b4e34a4538a6d122eee8d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1246
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Compilation fails with set_debug_port undeclared in ramstage and
smm code. Fix that by adding usb_debug.c to the appropriate stages.
Change-Id: I2a037d3c5fab76ae6ea65c3a7f4d4e7561bb6d34
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1376
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Modelled after http://review.coreboot.org/#/c/443 to get bd82x6x in
sync.
Change-Id: I36d715310157b9f9074f2a1c80710f85833020b4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1324
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This will log if the ME is disabled or has an error.
1) disable ME via EC console: gpioset PCH_HDA_SDO 1
2) boot the device
3) read eventlog with "mosys eventlog list"
71 | 2012-07-13 10:10:55 | Management Engine | Disabled
Change-Id: I9f6ee452d2aea76e6a5ea2cd50a50ff36245692a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will allow various teams to select which thermal sensor
will control the thermal zones.
Also add a method to notify the thermalzones of a change
so these threshold/sensor methods take effect.
Needs a modified BIOS that uses the NVS TMPS value in
the thermalzone to read a different sensor.
Then, use a kernel driver that contains the following:
/* Adjust temperature sensor id to 2 */
union acpi_object param;
struct acpi_object_list input;
param.type = ACPI_TYPE_INTEGER
param.integer.value = 2
input.count = 1;
input.pointer = ¶m;
acpi_evaluate_object(NULL, "\\TMPU", &input, NULL);
And ensure that the temperature sensor that is being
monitored switches to ID 2.
Change-Id: I6319741358ba31eb8a3dc635d64f3f0acf683386
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME device was being sent EOP and the PCI device hidden during
coreboot so it was not available in the SMI finalize step.
This also flips the PCI vendor/device dword around for the match.
Boot on Panther Point with serial and SMI debugging enabled and see
that ME EOP message is sent and the device is hidden at end of
U-boot and before the kernel loads.
Finalizing Coreboot
SMI# #0
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PM1_STS: TMROF
PM1_EN: 120
Starting kernel ...
Change-Id: I230038c62c50db2a1c94078c0a2a67bdc232440e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1338
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The LPC bus normally allocates the range for legacy devices,
0-0x1000. Some devices on LPC are above that range and need to
be accounted for. Check the decode range settings for addresses
> 0x1000 and reserve them.
Change-Id: Idba800d7cee3185296f29dd237ba306f3de8de55
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1337
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Events are logged for SMIs that trigger ACPI sleeps state
entry and when the power button press triggers an SMI such
as at the developer/recovery screens.
Generate ACPI sleep state events and power button
events and verify they show up in the log:
153 | 2012-06-23 17:12:59 | ACPI Enter | S5
184 | 2012-06-23 17:15:50 | ACPI Enter | S3
216 | 2012-06-23 17:28:58 | Power Button
Change-Id: Iba134d619780e459bce189d36d57844997ffb009
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1320
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Unfortunately the drive strength values are very much board
specific and different between mobile and desktop so we don't
try to do any fancy detection here but let it be specified
directly in the devicetree.
Change-Id: I66674bff0de04ecd088fb09afad1cf801a374df2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to support the GSMI interface the SMI handler needs
to find and use the state save area from the same CPU that
initiated the SMI. In this case it is a synchronous SMI
resulting form an IO write to port 0xB2.
To find the right CPU state save area iterate over the region
until the "IO Misc Info" field reports the expected value and
then proceed to use that state save area.
This is needed because the coreboot SMI handler only executes on
one core, and that core is non-deterministic. It is likely that
the core executing the C SMM handler is not the same one that
actually did the IO write to 0xB2 and generated the SMI.
The GSMI parameter buffer is passed as a pointer to EBX in the
tate save area, and the GSMI command is extracted from EAX before
it is used as the return value.
This interface is tested by enabling CONFIG_GOOGLE_GSMI in the
kernel and generating events and verifying that they end up
in the event log.
159 | 2012-06-23 16:22:45 | Kernl Event | Clean Shutdown
184 | 2012-06-23 17:14:05 | Kernl Event | Oops
185 | 2012-06-23 17:14:05 | Kernl Event | Panic
Change-Id: Ic121ea69e9f50c88467c435e095c3e3629989806
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a temporary workaround so the SPI bus can be accessed
at runtime in SMM code until the SPI opcode menu is used
properly.
Change-Id: I93d188c55b66d8dce49fa91a1de53ee195944b30
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is called from the SMI handler install because those
setup functions clear many of these registers.
Ensure that these events show up in the log as appropriate.
Example log output:
159 | 2012-06-23 14:31:54 | SUS Power Fail
160 | 2012-06-23 14:31:54 | System Reset
161 | 2012-06-23 14:31:54 | ACPI Wake | S5
Change-Id: I48c423c10ee7e6c2829bcc95f6cfabb4979c25a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is exported so it can be used in other
places that need similar relocation due to TSEG.
Change-Id: I68b78ca32d58d1a414965404e38d71977c3da347
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1310
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was introduced when porting the SPI driver over from u-boot but it
is not needed. Hence drop the extra typedef and use device_t instead.
Change-Id: I3ab797a8e482d1c9aa1d004e488e99aeaffcdd8b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1331
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
CPUs with configurable TDP will run the TSC at the max non-turbo
ratio for the maximum TDP value, which can cause issues if another
TDP is desired. To deal with this we set the flex ratio to the
nominal TDP ratio early in the boot and then configure the Soft
Reset Data registers so the PCH can tell the CPU what frequency
to run at after a reset.
This is done very early in the bootblock because it is necessary
to reset the system after setting a flex ratio.
The end result is that the TSC will now increment at the max
non-turbo frequency for the nominal TDP.
On some system with 1.8GHz CPU ensure that the kernel
detects the CPU speed as ~1800mhz rather than ~2300mhz:
> dmesg | grep "MHz processor"
[ 0.004000] Detected 1795.801 MHz processor.
Change-Id: I8436dced9199003b6423186a2b041e3f7b84ab8c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are enough differences that it is worth defining the
proper map for the sandybridge/ivybridge CPUs. The state
save map was not being addressed properly for TSEG and
needs to use the right offset instead of pointing in ASEG.
To do this properly add a required southbridge export to
return the TSEG base and use that where appropriate.
Change-Id: Idad153ed6c07d2633cb3d53eddd433a3df490834
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1309
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- add Kconfig option for CONFIG_SPI_FLASH_SMM
- compile subsystem and chip drivers for smm if enabled
- change mdelay(1) to udelay(500) since mdelay is not defined
in SMM and a 1ms delay is worth avoiding
- make flash chip structure non-const so the probe function
pointers can be relocated for use in TSEG
- Make SMM PCI access possible in southbridge SPI code
Change-Id: Icfcbbe8e4e56658769d46af0b5bf6c79a6432641
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1313
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME needs to be talked to through the PCIe memory mapped config
space.
Change-Id: Ic2c5a572a126722a08a82d95df13d11507586c6b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1284
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In the short term there might be devices with Sandy Bridge CPUs
on mainboards with Panther Point PCHes. While this configuration
option is perfectly valid, coreboot currently ties Sandy Bridge to
Cougar Point and Ivy Bridge to Panther Point. One occurence is in
the ME handling code.
To make coreboot most flexible, compile both ME handlers into
coreboot and decide at runtime which one to use.
Change-Id: Icffe2930873f67c99c3f73e37e7a967f4f002b88
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1280
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- On Cougar Point there may have been stack corruption during the
ME hash verification
- On Panther Point the ME firmware hash was not passed on to the
OS
Change-Id: I73fc10db63ecff939833fb856a6da1e394155043
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The PCIe device enable function prints when it disables a device.
The PCIe ports(bridges) use a different routine that didn't print
the message. Add it to be consistent and to provide better debug
output.
Change-Id: I8462c48e7f4930db68703f0bfb710c01c9643a98
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1326
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to
"disable",
power-off, replug device -> device turns on; and similar cases).
Modelled after http://review.coreboot.org/#/c/444
Change-Id: I2b8461dff1ae085c1ea4b4926084268b4da90321
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1323
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The function was too eager shifting stuff around, this change corrects
the problem.
Change-Id: I4c13dbe86cb627835dae05bb74af9867c28e143d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1291
Tested-by: build bot (Jenkins)
There are enough subtle differences in the magic values that
it is easier to make a separate function.
This fixes a reset hang with pantherpoint chipset.
Change-Id: I02b03cb37e5fd5ee2fd62067644f0a62dc2cd26a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1322
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This makes it available early in romstage without having to
worry when the different romstagse enable it.
Check for extended CMOS to be enabled in early romstage.
This is used by a later commit which uses the extended
CMOS region for stoage.
Change-Id: I9e026d48499c63d6503c2b020d4cc3047126fa93
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1306
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Convert all PCI ID lists to new scheme
- Unify code (variable names)
- add missing PCI IDs for Panther Point PCIe root ports.
Change-Id: I6357f6ebce7ddffe45a3ec642b0c594147f6134c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1301
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
With this patch it is possible to use the smbus in ramstage. The
biggest part of the patch is a simple code split into a general
part (smbus.h) and the concrete users (early_smbus.c and cs5536.c).
After the switch from romstage to ramstage the smb base address
has changed, but that is no problem as the new base address is
stored in bar0 of the ISA bridge. It could also be read via msr,
but via PCI it is simpler. I used the following patch as
reference on how to readout the new base address:
http://lists.laptop.org/pipermail/commits-kernel/2006-November/000178.html
Change-Id: I9f86a1e474368c62f9ed3a95edfb3e63117aa156
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1243
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We don't ever free memory in coreboot, hence drop spi_flash_free() and
spi_free_slave()
Change-Id: I0ca3f78574ceb4516e7d33c06ab1a58abfb3b0ec
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1273
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Hudson code has been integrated from CIMx to AGESA. This patch is about the wrapper.
Change-Id: I63d951982140b82a3a77a97eb3d55fc75fc0caa3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1157
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
awk on Cygwin created the UTF-8 value for the 0xff code point,
which makes it two bytes wide. This broke the build.
Change-Id: I4937ae7ce1136ba7a76d05b42f9dd2771203175d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1164
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Required for Supermicro X7DB8, which needs the FBDIMM clock generator
setup during romstage.
Change-Id: I30ca8354087e851487aee0614595782131d4d9bc
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1116
Tested-by: build bot (Jenkins)
i3100/i5000 have a second IOAPIC which handles IRQs for PCI-X.
Add code to enable it.
Change-Id: Ib447628f501b152c8adc9c7c89bd09b5615b9e5a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1118
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The constant value 0x100000000 is used in linker scripts to calculate
offsets from the end of 32-bit-addressed memory. There is nothing
wrong with it, but 32-bit versions of ld do the calculation wrong.
Change-Id: I4e27c6fd0c864b4d98f686588bf78c7aa48bcba8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1129
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
- Add #define to allow the FADT PM Profile to be overridden.
- Change the location of the PMA_CNT_BLOCK_ADDRESS to match
current documentation.
- cst_cnt should be 0 if smi_cmd == 0
- add a couple of default access sizes.
- Add a couple of #define values for unsupported C2 & C3 entries.
- Add PM Profile override value into amd/persimmon platform.
This does not use the #defines in acpi.h so that the files that
include this don't all need to start including acpi.h.
Change-Id: Ib11ef8f9346d42fcf653fae6e2752d62a40a3094
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1055
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This change adds utility functions which allow to read any GPIO pin,
as well as a vector of GPIO pin values.
As presented, these functions will be available to Sandy Bridge and
Ivy Bridge systems only.
There is no error checking: trying to read GPIO pin number which
exceeds actual number of pins will return zero, trying to read GPIO
which is not actually configured as such will return unpredictable
value.
When reading a GPIO pin vector, the pin numbers are passed in an
array, terminated by -1. For instance, to read GPIO pins 4, 2, 15 as a
three bit number GPIO4 * 4 + GPIO2 * 2 + GPIO15 * 1, one should pass
pointer to array of {4, 2, 15, -1}.
Change-Id: I042c12dbcb3c46d14ed864a48fc37d54355ced7d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1049
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Right now coreboot compilation fails when SPI flash debugging is
enabled. Fix it by using the right set of memory functions.
Change-Id: I5e372c4a5df53b4d46aaed9e251e5205ff68cb5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1044
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Experiments have shown that writing plain value of 6 at byte io
address of 0xcf9 causes the systems to reset and reboot reliably.
Change-Id: Ie900e4b4014cded868647372b027918b7ff72578
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1050
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The fadt legacy free logic was backwards.
Change-Id: Ieb21ef335f7514ced70248d0bf8668ddb73cf59f
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1030
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
The FADT iapc_boot_arch indicates the available information
for accessing legacy devices. By default, the setting supports
legacy. LEGACY_FREE and/or the iapc_boot_arch field may be
customized.
Change-Id: I5679741e1f8db923d3c00b57f6a5d813550f3a5e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1024
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
The South Station recieved updates that fix a number of fadt problems.
South Station now uses the southbridge fadt.
Change-Id: Ib990a69a359a4b7eae3431bb4323acd537acda1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1021
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
This driver is taken from u-boot and adapted to match
coreboot. It still contains some hacks and is ICH specific
at places.
Change-Id: I97dd8096f7db3b62f8f4f4e4d08bdee10d88f689
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/997
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change source file modes from 755 to 644
The following files have been grepped for changes:
*.c
*.h
*Kconfig*
*Makefile*
Change-Id: I275f42ac7c4df894380d0492bca65c16a057376c
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1023
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The fadt.c is the same across all the platforms using the sb800
cimx southbridge wrapper.
Change-Id: Ifbbfc238732aa46aef96297eaa188b77d27151f3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1019
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are the PMIO & PMIO2 read & write routines from
src/southbridge/amd/sb800/sb800.c & sb800.h for use in the cimx
tree. Currently most platforms using CIMX are calling WritePMIO()
directly from the src/vendorcode/amd/cimx/sbX00 directories
instead of using a wrapper function.
These functions only do byte reads & writes.
Change-Id: I881a6e2d4ddbba3dbdf4dd33e06313fe88b3682a
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/981
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current early PM setup that attempts to configure dynamic clock
gating relies on PCIe functions to be enabled that may not be.
Instead of reading port 0 or 4 directly to determine the link width
use the register that refelects the soft strapping options as this
will always be available.
Also add a clear register assignment and break for port 0 in the
switch statement instead of falling through to port 4 as that could
end up setting the slot power limit based on port 4 values instead
of based on port 0.
register 0xE1=0x3f and all other root ports should have 0xE1=0x03.
When port 0 and 4 are disabled they will have 0xE1=0x3C before
being disabled by the pch enable handler.
LUMPY default:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 3 0xe1
0x03
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 1 0xe1
0x03
Change-Id: I33a37b0ec0c8e570cf5d9dda2c06e0225fee135c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/980
Tested-by: build bot (Jenkins)
Background: The PCI spec (3.0-3.2.2.3.4) requires that PCI devices
implement function 0. The Linux Kernel therefore will not enumerate
a PCI device if it does not present a valid config space at function 0.
If a board does not have anything connected to root port 0 and it is
desired to disable the unused ports in order to save power then this
will cause the other downstream PCIe devices to go missing as they
will not be enumerated.
Intel chipsets provide a way to map root port numbers to different PCI
function numbers, thereby avoiding this issue and allowing root port 0
to be turned off.
This change adds a new chip config option 'pcie_port_coalesce' that
will collapse the enabled root ports into a linear map starting at
zero. This option defaults to disabled as it can have a confusing
effect on the system as the declared static devicetree may not match
what is seen at runtime. This option is also forced on if the static
devicetree disables port 0.
When each root port is processed in the early enable stage it looks
for a lower numbered root port that has been disabled and then swaps
the two assigned function numbers.
However the mapping register is write-once so it has to keep track of
the proposed mapping changes until all ports have been processed
before writing out the final map value. At this point it also updates
the function numbers in the static device tree so they are consistent
with the new layout.
There are a few other closely related fixes in this change:
1) There is a power savings opportunity if an entire bank of ports
(0-3 or 4-7) are disabled. This was checking the chipset revision to
look for CougarPoint B1+ stepping and that was not passing on
PantherPoint where this should always be applied. To fix this I added
a function to determine the chipset type based on comparing the upper
byte of the device ID.
2) Apply the same chipset type check fix to the IOBP programming.
3) There is another power savings opportunity to enable dynamic clock
gating on shared PCIe resources which only applies to ports 0 and 4.
However if 0 or 4 is disabled then the later check to enable this
would fail as that device is already hidden.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
Change-Id: I828aa407fdc9c156c1c42eda8e2d893c0aa66eef
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/979
Tested-by: build bot (Jenkins)
The chipset enforces static-defined interrupt swizzling on PCIe root
ports so if a port is remapped to a different function it needs to
still report the proper interrupt map to the OS instead of assuming
that function number is equivalent to root port number.
This change also includes an update to the PCH function disable
register which was incorrect for CPT/PPT and would cause unpredictable
behavior if used.
The kernel command line was changed to add 'nomsi' in order to force
PCIe devices to use IO-APIC assigned interrupts and not MSI to ensure
that the mapping is correct.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 41518 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 720 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 38988 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 347 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
Change-Id: Ia5f6bb8888b5c38a5dbc88bb25ecdf1fca41ee3e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/978
Tested-by: build bot (Jenkins)
The sata controller comes up in legacy/normal mode and
is currently put into AHCI mode in romstage.
If that is removed and the controller is left alone until the
ramstage driver (like we do on Stumpy/Lumpy) then the resource
allocator will have configured the device for IDE mode with an
IO address in BAR5. Then when the ramstage driver puts the
controller into AHCI mode it will not have the correct resources
to do the rest of the AHCI setup.
So the controller mode needs to be changed in the enable stage
rather than in the init phase. This same register contains
the port map and it is a R/WO (write once) field so the configured
port map must be written at the same time. For non-AHCI mode
the devicetree map was ignored before but it is used now.
Since the port map register is now written at enable step it
does not need to be written again during init.
With this change the sata port map can be reduced to just port 0
and then U-boot does not have to probe all available ports.
Change-Id: I977952cd88797ab4cea79202e832ecbb5c37e0bd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/977
Tested-by: build bot (Jenkins)
The OS does not re-execute the APMC 'enable ACPI' SMI
on resume so this has the potential to leave things
in an unknown state.
Change-Id: Iaf0fcb99f699e9e0ecacaab3f529026782a95151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds the PCI device id of the LPC controller identifying the
QPRJ/QS stepping of the Panther Point southbridge.
Change-Id: Idcaa7dbd30224e3690ea469c6cb74f75de287631
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Many PCI devices share the very same driver despite having different
PCI device IDs, which causes a lot of copy and paste of driver
definitions.
This change introduces a way to specify the array of acceptable
device IDs in a single driver entry. As an example the Intel
{Sandy|Ivy} Bridge SATA driver is being modified to use a single
driver structure for all different SATA controller flavors, a few
more Ivy Bridge IDs are being added as well.
BUG=none
TEST=manual
. modified coreboot brought up an Ivy Bridge platform all the
way to Linux login screen.
Change-Id: I761c5611b93ef946053783f7a755e6c456dd6991
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
post_code() was added in our internal tree by duplicating code. It's not of
much use at this point, since the code is quite well tested, so avoid bloating
the bootblock (since compiled with ROMCC).
Also add some missing include files that didn't seem to be needed with an
older version of coreboot.
Change-Id: Id62b838728a247e8bcadb4f1db17269be0d4f3f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
rename from mainboard_apm_cnt to mainboard_smi_apmc to match the function
naming scheme of the other handlers. Add prototype for mainboard_smi_sleep
(mainboard specific S3 sleep handlers in SMM) that is required by Sandybridge.
Change-Id: Ib479397e460e33772d90d9d41dba267e4e7e3008
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/933
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add early_smbus.c for romstage-y list and remove respective
include on mainboard romstage.c files.
Tested on AOpen board.
Change-Id: I1c7e6cb32e3a9d7cc9b6037dc27e59149d492001
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/909
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
S3.rom is useless for all the other boards which don't use flash to
save sleep/wakeup settings. AGESA-based boards other than persimmon
haven't been validated the S3 resume. They don't need S3.rom yet.
Change-Id: I12693e9556ca6f8e0d80b2ab2dca5c85bdb97685
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/902
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some places still hardcoded the address instead of using IO_APIC_ADDR.
Change-Id: I3941c1ff62972ce56a5bc466eab7134f901773d3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It is for S3, storing the recovring data in the nonvolatile storage,
i.e., flash.
Change-Id: Ie9e4f42a80c93d92d2e442f0e833ce06d88294f9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/620
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
So far it just setups things right for Bifferboard. We may change it
in the future to fit other hardware.
Change-Id: I1c4ccff4e47b9cb9e31a738f038fc4f4ebe59087
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/808
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to "disable",
power-off, replug device -> device turns on; and similar cases).
Change-Id: If1d88c1c34c3333b636ed3ec1e1fb9bea394e615
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/444
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Change-Id: Ib83aa07a3e55bed075150354a060317ebc9d5ba7
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/443
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use separate Kconfig option to select a driver directory for
build and the specific type of southbridge to support.
Change-Id: I9482d4ea0f0234b9b7ff38144e45022ab95cf3f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Also mark the corresponding lint test stable.
Change-Id: Ib7c9ed88c5254bf56e68c01cdbd5ab91cd7bfc2f
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Southbridge SP5100 support was compiled with SB700 code, but static
device info structure would use sp5100/chip.h. To solve this drop
support for separate chip sp5100 and adjust the relevant Kconfig
options.
Removes chip directory:
src/southbridge/amd/sp5100/
Rename Kconfig option
from: SOUTHBRIDGE_AMD_SP5100
to: SOUTHBRIDGE_AMD_SUBTYPE_SP5100
Change-Id: I873c6ad3624ee69165da6ab7287dfb7e006ee8e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/679
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I16b27e40ca1a201b2f968f8ce303eaafe43804c0
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/660
Tested-by: build bot (Jenkins)
If PCI config cycles use MMIO instead of I/O in the SB600 bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O and
configures the southbridge decode range to what is defined by the
mainboards Kconfig.
Change-Id: I85297237f32f37b3fc1ff5b488cca0a43bcf20fd
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/632
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If PCI config cycles use MMIO instead of I/O in the SB700
bootblock code the cycles will go nowhere since the MMIO feature
hasn't been configured yet. This change forces the cycles to use
I/O and configures the southbridge decode range to what is specified
by the mainboards Kconfig.
Change-Id: I15a89a27645edf594d14ef20f129f75a315e9672
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/631
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If PCI config cycles use MMIO instead of I/O in the bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O.
Change-Id: I93dec45f7cd6764cef7736c774a4d4e61bf7d7e0
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/630
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Extend the Family10 revisions checked byt the printk message.
Change-Id: Ia94daeefb1aabfb128c577b1e0aa52cf63d5cf44
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/633
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ibfb7b294aa5007ac2f767d85e090572f85148bad
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/659
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I7a7a1919b7a555156b8da21e8db7dd8f682d68e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/661
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ifba0b65d81af60774f368d151e935ae1cc768336
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/662
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I9762ef01fc10c453ef643599c1c5dc8ee78081c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/663
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I83105e92d1cc5d2d12aede564a1ab9c5d912ac56
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/664
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I521deecf58e5d5de303f1ef2f5ff7e965294de18
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/665
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge. (cimx/sb800 is a "different"
chipset)
Change-Id: If7cf2a141a1f2df60f687c51fbd760aa405c8480
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/666
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The current directory is always part of the search path of cpp when
using #include "..."
Change-Id: I74fe39e0c79835e4b9a927afcbeab21040d8ae52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/648
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix issues reported by new lint test.
Change-Id: I077a829cb4a855cbb3b71b6eb5c66b2068be6def
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
No in-tree amd8111-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: Iabbaa4cd2fd367ed6decec7ef5cdcbae3b264d52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/654
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
No in-tree 82801dx-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: I69671cb6411a6cd9c791059ae9546dff3aff702c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/655
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
without it, you can't boot from PCI devices like scsi controllers
which require an interrupt set. So preconfigure all pci devices.
Change-Id: I2cd781227701e8363d83bd90e0e36994359fc194
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/603
Tested-by: build bot (Jenkins)
BIOS needs to set the bit mask which ports are iplemented on the
board. Without setting this option, seabios fails to boot from
SATA.
Change-Id: I21de3fde3a9cff7c590226f70fa549274f36e2a8
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/601
Tested-by: build bot (Jenkins)
i3100 misses the magic SATA init sequence, which makes all
requests fail. Captured from the vendor BIOS, which writes
those bits on all configurations.
Change-Id: I293b7d9cd681181311ecaced6d7df9b2706c711f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/600
Tested-by: build bot (Jenkins)
Change-Id: Id34615f0c229d276d72cdf984cf82ea8cc1a85bb
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/523
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We used to put the id section at -0x10, with some boards overriding
this to avoid collisions with romstraps.
Hardcode the location at -0x80, at the possible expense of some space
(0x70 bytes).
This also makes the section easier to find in a binary image.
At some point, CONFIG_ID_SECTION_OFFSET can be removed, so this option
is moved to src/Kconfig.deprecated_options.
Change-Id: I6ce2d6e94e57717939bda070bfe0c9df80ca2a89
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/549
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Change-Id: Ie3872c57990f9784aafda14f8c7fc842b3a65260
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Kyösti Mälkki