Change Setup Stage of control messages to have no retries, while data
and status stages may retry until timing out after 1000 retries.
The correct amount of retries might vary by endpoint and device dongle
used, so make it a variable.
Change-Id: I63313f994d0bd3444a3aab527ca942da5de9e6fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3882
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Transaction consistently completes with 80 to 150 status reads on my
setups. Hardware should always be able to complete this within 125us
as the debug port is serviced at the beginning of each microframe.
Timeout is set to DBGP_MICROFRAME_TIMEOUT_LOOPS=1000 status reads. Do not
retry transactions if this timeout is reached as the host controller
probably needs full re-initialisation to recover.
If this timeout is not reached, but a transaction is corrupted
on the wire, or it is otherwise not properly delivered to the USB device,
transaction is retried upto DBGP_MICROFRAME_RETRIES=10 times.
Change-Id: I44bc0a1bd194cdb5a2c13d5b81fc39bc568ae054
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3881
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
These allow to define a kernel image, initrd and command line.
Change-Id: I40155b812728a176b6d15871e1e6c96e4ad693c8
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3893
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
It wasn't even hooked up to the build system anymore.
Change-Id: I4b962ffd945b39451e19da3ec2f7b8e0eecf2e53
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3892
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Add support for control messages with a write of data stage.
Add status stage after a read of non-zero length data stage.
Do not retry control message if device responds with STALL.
Change-Id: I16fb9ae39630b975af5461b63d050b9adaccef0f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3867
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
USB defines a mechanism to detect certain cases of lost handshakes
using an alternating data sequence number, referred to as data
toggling. This patch fixes each pipe to have its own tracking of
the data toggle state.
Change-Id: I62420bdaeadd0842da3189428a37eeb10c646900
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3865
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Add allocation for endpoint0 as a pipe for control messages.
Endpoint number was already stored in the pipe object, place devnum
there too, although all pipes will use same devnum==127.
Change-Id: I299d139bdd8083af8b04a694e8e41435ec026a25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3864
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Add option to choose one of the EHCI controllers in recent
intel chipsets for usbdebug use.
Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in
rcba_config() for some mainboards, check the PCI class code
for match.
Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3440
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Two new nvram variables control disabling the two non-ME NICs
on the mainboard. This is implemented by disabling their PCIe bridge.
Change-Id: I086f0d79de3ad0b53fa0ec40648d63378070e3bd
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3870
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Collect early timestamps in Lenovo X60’s romstage.
Selecting the option `COLLECT_TIMESTAMPS` in Kconfig and then
doing `cbmem --timestamps` should output the timestamps.
Change-Id: I7bd30f03a1b85c38e89c19cdf88b2d20b24abed8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3587
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The northbridge defines it already and to the same value.
Change-Id: Ia5d856258fac52ea0b249142f70a89123ca04f82
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3876
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested on Ubuntu 12.10. S3 is supported. No HD Audio.
Mainboard details: http://www.asrock.com/ipc/overview.asp?Model=IMB-A180
Change-Id: I75254194ab5da8e5c61383d8f85aa4e300815637
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3880
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
src/southbridge/amd/agesa/hudson/Kconfig config default value,
mainboard Kconfig config value for specific mainboard.
bit 1,0 - pin 0
bit 3,2 - pin 1
bit 5,4 - pin 2
bit 7,6 - pin 3
Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3879
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Add a function to test if pci_devfn_t matches with a device
instance of struct device, by comparing bus:dev.fn.
Change-Id: Ic6c3148ac62c7183246d83302ee504b17064c794
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3474
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PNP access
functions for ramstage using the inlined functions from romstage.
Change-Id: I2a0bd8194acaf9c4c7252a29376eec363397e3a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3871
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PCI access
functions for ramstage using the inlined functions from romstage.
Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
After an USB device sees USB bus reset on the bus, it will reset to
device number 0. Per the EHCI debug port specification, a debug
dongle device may reset to the fixed debug device number of 127 instead.
Thus there is no need to try device numbers from 1 to 126.
Do a sanity-check on a returned debug descriptor as I experienced
some USB flash memory to respond on this request with zero-fill data.
Change-Id: I78d58f3dc049cd8c20c6e2aa3a4207ad7e6a6d33
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3861
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Resetting an EHCI controller when it is not halted can have
undefined behaviour. This mostly fixes a case where calling
usbdebug_init() twice would fail to reset the USB dongle device
properly.
On amd/persimmon it still requires one extra retry, but at least it
is now possible to have usbdebug enabled for both romstage and
ramstage.
Change-Id: Ib0e6e5a0167404f68af2edf112306fdb8def0be9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3862
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Ported from spi/winbond.c.
Fixes this error:
ICH SPI: Too much to write.
Does your SPI chip driver use CONTROLLER_PAGE_LIMIT?
Change-Id: I50db8fd1104d3b7d319b278b14f97e3ff9cb6404
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3877
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This quirk is needed with a DIY debug dongle using obsolete
CY7C68013 (aka FX2) USB chips. Old revision of chip requires a
SET_CONFIGURATION to be sent, while this is not required in EHCI
debug port specs.
Change-Id: I4926eb19b7e991d6efeef782682756571ad006b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
When we create low-level debugging of EHCI controller registers,
we call printk() within printk(). In ramstage this would leave us
with deadlock waiting on the console spinlock.
Change-Id: Idbe029af9af76de27094bb2964c60d9ccfdd96e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3860
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If ramstage is not compressed, the CBFS module in romstage doesn't
need to support LZMA. Removing the LZMA module in this case can save
about 3000 bytes in romstage.
Change-Id: Id6f7869e32979080e2985c07029edcb39eee9106
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3878
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The AMD AGESA function to move the stack from cache-as-ram to
actual RAM doesn't need any help. The current implementation has
an INVD instruction just before cache-as-RAM is torn down. It isn't
needed for Trinity processors and makes Kabini boot unreliable.
Change-Id: Ibe9e4105eee032471ccbb2d537471d5fa5847d22
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3852
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
It still pointed to the old binary despite implementing the newer interface
Change-Id: Iebd5dae98168f5568f3ad6a18c5ebde9abc3ece0
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3869
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Drop unused and commented out variable, and fix a comment while at it.
Change-Id: I1bd7d10aca949c8579433ea1c91264fd816a3fb4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3873
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
SEABIOS_PS2_TIMEOUT needs a default, otherwise the "allyesconfig" target
hangs in an endless loop.
The given default is correctly overridden by the (currently sole) user,
the lenovo/x60 target.
Change-Id: I3f5e347c29ccbb4d711a489d067b6c909f030bd0
Reported-by: Kyösti Mälkki
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3874
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Add Kconfig option SQUELCH_EARLY_SMP and have it enabled by
default.
Console drivers have unpredictable results if multiple threads
attempt to share same resources without spinlock. Serial UARTs
have not had huge problems, only distorted output, but those
relying on cache-as-ram (CBMEM and usbdebug) may require this.
Change-Id: I7f406fdea7b6dc6a341c4da2fab56f7b7ff568b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3854
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Move the floppy drive enumeration from _INI() and PROB(),
which stored the enumeration results into _FDE into _FDE().
_INI is called by any ACPI-capable OS on boot while _FDE
is rarely used. So it's better to run the enumeration when
requested rather than unconditionally.
Change-Id: Icf1e2a551806592faa8ba8d80fa8d02681602007
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The parallel port of the W83627HF can be configured on any port
between 0x100 and 0xFFC with 4 byte alignment for traditional modes
and 8 byte alignment for EPP mode. As the ACPI specification says
that the maximum acceptable starting address has to be a multiple
of the alignment granularity, correct the maximum starting address
from 0xFFC to 0xFF8.
Change-Id: I272e09d091149791f2867b1d06e4fc27bc1bb2cd
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/2942
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows mainboards to preconfigure a ps2-keyboard-spinup
timeout when SeaBIOS is chosen as the payload.
The Kconfig option can be changed manually if CONFIG_EXPERT is set.
Change-Id: I5732b18ef04f4bdef6236f35039656ad02011aec
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3734
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The slightly hackish ioapic ressource reservation is needed for i440fx
emulation only, for q35 the ich9 southbridge driver handles this just
fine.
[ Side note: The i440fx chipset emulated by qemu is pimped up with alot
of stuff which never existed on real hardware, which leads
to tweaks like this one. ]
Change-Id: I06bf54cbc247ccf17aa9063fb7dee9def323c605
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3850
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The board name in that variable name is not necessary, as it is not board
dependent, that means using the file as a template for making a new
coreboot port for another motherboard the variable does not need to be
changed, and just increases the code differences between AMD Parmer,
AMD Thather and ASUS F2A85-M. So use a generic name.
The same was done for AMD Persimmon (and inherited by the LiPPERT
FrontRunner/Toucan-AF) in the following commit.
commit 5e70766f14
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Tue Feb 26 15:56:11 2013 +0100
AMD Fam14 boards: reduce unnecessary differences, 2nd attempt
Reviewed-on: http://review.coreboot.org/2529
The board name is *not* removed from the `CODEC_ENTRY` variable name as
the verb table not only depends on the codec but also on the board [1].
Having the board name in the variable name is a good indicator that the
pin configuration needs to be adapted when taking this file as a template
for a new port. If it was board independent, a default chip configuration
could be used and shared between all boards, which is unfortunately not
the case.
[1] Unfortunately I was not able to find Jens’ comment in my mail archive
and in the Gerrit Web interface. Not sure where it is, but I am sure
he made that comment.
Change-Id: I440a306cf4ff0a5b1b61d1983d70c66d129904d0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3199
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
As Nico noticed for the W83627DHG, the power management bits to power down
individual logical devices on Winbond superios are named counterintuitively
and need to be set when the logical device should be powered.
This corrects the power management methods for the W83627HF.
Change-Id: I98bccd550a0513c62bfa9480275f88c566691bc8
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3605
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For reasons explained in a previous CL, it might be necessary to "load" a file
from CBFS in place. The loading code in CBFS was, however, zeroing the area of
memory the stage was about to be loaded into. When the CBFS data is located
elsewhere this works fine, but when it isn't you end up clobbering the data
you're trying to load. Also, there's no reason to zero memory we're about to
load something into or have just loaded something into. This change makes it
so that we only zero out the portion of the memory between what was
loaded/decompressed and the final size of the stage in memory.
Change-Id: If34df16bd74b2969583e11ef6a26eb4065842f57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The ThinkPad keyboard controller sometimes needs a while in order
to initialize, so let's ask SeaBIOS to wait for it.
This change ensures that the internal keyboard always functions
correctly on the ThinkPad when coreboot is built with SeaBIOS as
payload.
Change-Id: I562475ec98b0c1f5d0debf6e9b597748a420f068
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3735
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
QEMU has a bunch of non-standard virtual devices on various I/O ports.
Allocate resources for them so the coreboot resource management knows
those ports are used.
Change-Id: I51a85967cf2dcd634b0c883210bb52c0c34c8283
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The _OSC method is used to tell the OS what capabilities it can
take control over from the firmware. This method is described
in chapter 6.2.9 of the ACPI spec v3.0. The method takes 4
inputs (UUID, Rev ID, Input Count, and Capabilities Buffer) and
returns a Capabilites Buffer the same size as the input Buffer.
This Buffer is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control Dword.
The OS will request control of certain capabilities and the
firmware must grant or deny control of those features. We do not
want to have control over anything so let the OS control as much
as it can.
The _OSC method is required for PCIe devices. During Linux boot,
an error is logged to dmesg if _OSC is not found.
Change-Id: Icf6e7a82284d03d23fd30ee7b7db17754e988c9a
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3823
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the AMD FCH ACPI code.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
Change-Id: Ib2d36f69a26b715798ef1ea17deb0905fa0cad87
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3822
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Split the Family16 (Kabini) DSDT file into logical regions.
Olive Hill is the only mainboard and Kabini is the only NB/CPU
currently using Family16 AGESA code.
Change-Id: I9ef9a7245d14c59f664fc768d0ffa92ef5db7484
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3821
Tested-by: build bot (Jenkins)
Hook this up into the DMP Vortex86EX. Before under Windows XP
the microphone did not work. With the new logic it does. Now
line-in,line-out and microphone all work.
The verb data table is generated by Realtek.
Change-Id: I1bcef898a15547c86c12c4b52ce0069d13e23c84
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3855
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This module uses cim_verb_data to detect and initialize HD audio
codecs.
The module source code is based on southbridge/intel/sch/audio.c and
southbridge/nvidia/mcp55/azalia.c.
Change-Id: I810fef6fdcf55d66f62da58c3d7d99f006559d6e
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3844
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Add option to log changes in USB 2.0 EHCI debug port connection.
For romstage move usbdebug as the last initialised console so one
actually can see these messages.
Init order of consoles in ramstage is undetermined and unchanged.
Change-Id: I3aceec8a93064bd952886839569e9f5beb6c5720
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3387
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
These Kconfig entries were forgotten from the commit
that re-enabled usbdebug for these southbridges.
Change-Id: Ia17f1dd3340408da7c033c2c949404d2636bed44
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3849
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Rearranged the F2A85-M DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the F2A85-M dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for F2A85-M.
Change-Id: Ic72cb6004538ca9d9f79826b9b3c8d6aeb25017c
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3805
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Rearranged the Thatcher DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the Thatcher dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for Thatcher.
Change-Id: Ie44a32959cc547840914365e872416d4624d33df
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3804
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Support code for sb700 and sb800 existed already, but Kconfig and
compile-time issues prevented from enabling USBDEBUG for boards
with the affected AMD southbridges.
Change-Id: I49e955fcc6e54927320b9dc7f62ea00c55c3cedf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
With USBDEBUG selected, the file is built for both romstage and
ramstage. For the ramstage build, we need to explicitly use the
simple PCI config operations without devicetree.
Change-Id: I2de8d9c77bb458ba797c3aac9e2cd0d653e06684
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3437
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This change brings back the possibility to disable console
output while in romstage, like before commit d2f45c65.
For some platforms (AMD multi-socket) USBDEBUG and/or CBMEM
CONSOLE do not work correctly for romstage due the way
cache-as-ram is set up, but might already work for ramstage.
Change-Id: Id8d830e02a18129af419d3b5860866acf315d531
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3846
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Copied from a similar commit for Family 10h AGESA [1]
Remove the fourth argument in the comments. Luckily the compiler,
at least gcc, warns about a wrong number of arguments, and therefore
no incorrect code resulted from the wrong documentation.
[1] 07e0f1b AMD AGESA: Fix argument list for `PCIE_DDI_DATA_INITIALIZER` in comments
[2] fc47bfa Revert "AMD f14 vendorcode: Fix warning"
Change-Id: I3806e368a823e4a40d22e99b91bf3598d9ed2f15
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3840
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
This is the same patch as an earlier one applied to family 15 [1].
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
[1] e44a89f amd/agesa/f15/Lib/amdlib.c: Add missing breaks ...
Change-Id: Ibd1ae6f2b52fde07de3d978d174975f4d93647ab
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3839
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Change-Id: I7f6f6ff444fda4bdf233db1383919772afe6b635
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3815
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Olive Hill does not have a Super I/O or keyboard controller.
Change-Id: I8c1e5d8c20c4a964fe8d98df920b416382a26d9d
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3848
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
The VBIOS device ID is set by processor family using the
map_oprom_vendev() function in the northbridge code. There
is rarely a reason why this should be overridden by the mainboard.
Since Kabini includes a default VBIOS vendor/device ID in the
northbridge Kconfig code, remove the setting from the Olive Hill
mainboard settings.
Change-Id: Icd69155f5b51105d564dd82c89e4bb54a6118a82
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3816
Tested-by: build bot (Jenkins)
Add CONST modifiers to read-only pass-by-reference function
parameters in AGESA. This allows the use of "const" modifiers
on the declaration of lookup tables that are pass-by-reference.
These will be used to identify tables that are copied onto the
HEAP but don't need to be.
This same change was made for AMD Trinity APUs (Family15tn) [1].
[1] 283ba78 AGESA: Add "const" modifier to function parameters
Change-Id: I2bdd9fc5e027e938de9df0f923b95da934bb48dc
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3837
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This changelist was cherry-picked from merged community code
for Parmer [1] and the paths modified so that the Parmer
modification is applied against Olive Hill.
[1] 0086162 AMD SATA: Correct _them implement_ ... in comments
Change-Id: I9849e9a75dacfde15331c4200d72343a59036f14
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3841
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I14285f0677003fbf8b9b112207af202658807894
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Bruce Griffith <bruce.griffith@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3806
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Change-Id: Ifc180e6fcd594dbedc2512ea5bef283a3ad689d3
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3814
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Eliminate an unnecessary copy of the DDI descriptor list and
the PCIe port descriptor list. As descriptor tables, these
tables do not need dynamic updating and should be used from
ROM without runtime copying.
There will be a corresponding patch for AGESA that adds CONST
modifiers to function parameters that are pass-by-reference
"IN" values (read-only pointers).
Change-Id: I7ab78e58041e9247db22d0f97a6f76d45f338db0
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3818
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This patch sets a bit in the Yangtze southbridge to enable
the extra protocol necessary to handle port multiplier chips.
This has been turned on during most of Kabini development
without any notable impact. Olive Hill has an optional daughter
board that incorporates Silicon Image Steel Vines chips. This
change has been tested with and without the daughter board. This
change can be regression tested using any Hudson-based motherboard,
although it has no impact on boards with discreet Hudson/Bolton
southbridges.
This was tested for impact on SATA performance in the absence of
a port multiplier using the IOZone benchmarks within the Phoronix
Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were
connected to the ports on Olive Hill without using the port
multiplier card. The test results contained more run-to-run
variation within the same configuration than was seen in the
aggregate results comparing the interface with and without the
port multiplier protocol additions. In other words, the test
had less accuracy than the impact caused by turning on port
multiplier support.
Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3808
Tested-by: build bot (Jenkins)
Yangtze uses Hudson AGESA wrapper code but has some changes.
The changes are necessary and have no effects on Hudson.
Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
src/arch/x86/boot/tables.c and src/include/device/pci_ids.h are also
changed because these two files depend on F16kb northbridge macros
Change-Id: Iedc842f0b230826675703fc78ed8001a978319c5
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Bruce Griffith <bruce.griffith@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3782
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Change-Id: I4a1d2118aeb2895f3c2acea5e792fbd69c855156
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Mike Loptien <mike.loptien@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3781
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3812
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The Kconfig variable EXTERNAL_MRC_BLOB is not used.
Drop it.
Change-Id: I3caa5c2b6bcf5d2c13b6987da8ab3987bad0e506
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3829
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Directory intel/common must be conditionally added in the list
of source directories, as the parent directory southbridge/intel
is unconditionally added even for boards without such device.
Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3827
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The added device.h file was indirectly picked from cpu.h, which will
have this include removed in a follow-up patch.
Change-Id: Ifc0a4800de3b1ef220ab1034934f583be8c527b0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3826
Tested-by: build bot (Jenkins)
The EC expects the temperature in 64ths degree C. Alter
it8516e_set_fan_temperature() to just export this interface and
make the calculation more obvious.
Change-Id: Ibe241b7909f4c02b30b1e1200a1850d47695a765
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3785
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an option to set minimal and maximal PWM percentages when the fan is
in temperature controlled mode. Also fix a non-ascii flaw.
Change-Id: I85ae244bee2145bf17d6c29e93dd4871540985c8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3774
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC firmware expects a 255th while we provide a percentage.
Change-Id: Ib06a061b431ac728329043179800729e39e6166b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3773
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The IT8516E firmware of Kontron supports some selected external sensors
attached to the EC via SMBUS or GPIO16.
Change-Id: I4c451c360a393e916430e3bea04a95847455cef7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3772
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Removed the execute bit on all files in mainboard/amd/parmer/acpi
Change-Id: I85ffa66e0beb9c4bfe826b72968f7f633c224487
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3807
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change all PCI configuration accesses to MMIO in qemu-q35
emulation
To enable MMIO style access, add (move) explicit PCI IO config write
in the bootblock. As there is no northbridge/x/x/bootblock.c
file, a mainboard/x/x/bootblock.c file is added for this purpose.
Change-Id: I979efb3d9b2f359a9ccbd1b4f6c05f83bab43007
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3599
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Taking device_t as a parameter, this allows to alter the PCI config
access handlers. This is useful to add tracing of PCI config writes
for devices having problems to initialise correctly.
On older AMD platform PCI MMIO may not be able to fully configure all
PCI devices/nodes, while MMIO_SUPPORT_DEFAULT would be preferred due
to its atomic nature. So those can be forced to IO config instead.
Change-Id: I2162884185bbfe461b036caf737980b45a51e522
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3608
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Refactor the structure to better support receive and another
set of endpoints over usbdebug.
Change-Id: Ib0f76afdf4e638363ff30c67010920142c58f250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3726
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The code to figure out how to set num_starts was
starting to get kludgy. It's a constant for a given
CPU; constants should be constant; make it a config variable.
This change includes an example of how to override it.
Build but not boot tested; drivers welcome.
Change-Id: Iddd906a707bb16251615c7b42f2bfb5a044379b4
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3796
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
This is the first of a series of patches to provide support
for a new mainboard, Gigabyte GA-B75M-D3V.
This patch provides early serial for the superio and has been
tested on this mainboard. The code is based on IT8718F superio.
Change-Id: I5636199b49314166ed3b81e60b41131964dd44ff
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/3794
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Change-Id: If1fa39db79eeecbef90c8695143d2fe2adf2f21a
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3732
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The Linux thinkpad_acpi.c driver looks for this string while
reading information about the system it is running on.
This commit does not make the module load but it is one of
several things that the module looks for on a ThinkPad.
The use of 3 defines for the serial number template
seems odd but it's done in a way that eliminates
magic numbers, yet avoids use of strcpy, strlen,
strindex, strchr, or strspan: we can have some
correctness assured at compile time. Also, the
defines can be copy/pasted for other mainboards
and we should void errors due to people not changing
magic numbers.
Change-Id: Ief5f28d2e27bf959cb579c4c8eea9eecc9a89a7c
Signed-off-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3620
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
CBFS_ROM_OFFSET was declared in both the am335x config and the beaglebone
config. This removes it from the beaglebone config.
Change-Id: I657cb8e83a1ee961d8bdc995a41f303920bc53f9
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3771
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Split the Parmer, Family 15tn, and Hudson DSDT into groups. This splits
the DSDT table into includable ASL files which carry details specific
to the Family 15tn APU, the Parmer platform, and the Hudson FCH. The
dsdt.asl file in the mainboard directory contains only #include
references to the appropriate files.
Initially, this split was done by moving each piece of functionality
into its own file (e.g. IRQ routing and mapping, processor tree, sleep
states and sleep methods, etc.) and those pieces were #included in
dsdt.asl to ensure an exact match (via acpidump/acpixtract/iasl -d)
with the extant version of the table. Once the new tables were found
to exactly match the existing tables, the pieces were rearranged into
reasonable groups (e.g. fch.asl, northbridge.asl, pci_int.asl, etc.).
Some include files have no content but are left as a template for
other platforms and as placeholders for completing the ACPI
implementation for Parmer (e.g. thermal.asl, superio.asl, ide.asl,
sata.asl, etc.).
Change-Id: I098b0c5ca27629da9bc1cff1e6ba9fa6703e2710
Signed-off-by: Steve Goodrich <steve.goodrich@se-eng.com>
Reviewed-on: http://review.coreboot.org/3629
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
It might be the case that a file is being loaded from a portion of CBFS which
has already been loaded into a limitted bit of memory somewhere, and we want
to load that file in place, effectively, so that it's original location in
CBFS overlaps with its new location. That's only guaranteed to work if you use
memmove instead of memcpy.
Change-Id: Id550138c875907749fff05f330fcd2fb5f9ed924
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3577
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SOC's built in ROM loads the bootblock and the ROM stage into the on chip
memory before handing over control to the bootblock. To avoid having to add
one or more driver to the bootblock so that it can re-load the ROM stage from
whatever media Coreboot is stored on, we can just take advantage of the copy
that's already there. Loading the RAM stage/payloads won't be so simple,
so the ROM stage and the RAM stage will have to have different media drivers.
Change-Id: Id74ed4bc3afd2063277a36e666080522af2305dd
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3583
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This variable wasn't being defined and was defaulting to zero when used in the
ROM stage's linker script. This change defines it as a variable, and gives it
a value which is slightly beyond the end of the bootblock. By making the ROM
stage request to be loaded slightly farther into memory than it was loaded by
the SOC's masked ROM, we ensure that it's moved away from the stage's metadata
instead of on top of it. When it moves the other way, it clobbers important
values like the entry point vefore the bootblock has had a chance to use them.
Change-Id: I027a1365d05f1d79d7fc1e1349965ccb7d4e81b9
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3582
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The placeholder code in beaglebone's romstage.c didn't do anything, it just
immediately tried to load the RAM stage and jump into it. That doesn't
currently work, and there's no indication whether you actually successfully
got into the ROM stage or not.
This change adds a few lines which initialize the console and say "Hi" so that
we can tell that the ROM stage is running.
Change-Id: I45a0908c3ac65b21e0e5020428696d2e54933d0e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3581
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At least when building with the gnu toolchain, the headers the linker
automatically generate save space for the actual ELF headers in one of the
loadable segments. This creates two problems. First, the data you intended to
be at the start of the image doesn't actually show up there, it's actually the
ELF headers. Second, the ELF headers are essentially useless for firmware
since there's currently nothing to tell you where they are, and even if there
was, there isn't much of a reason to look at them. They're useful in userspace
for, for instance, the dynamic linker, but not really in firmware.
This change adds a PHDRS construct to each of the linker scripts used on ARM
which define a single segment called to_load which does not have the flag set
which would tell the linker to put headers in it. The first section defined in
the script has ": to_load" to tell the linker which segment to put it in, and
from that point on the other sections go in there by default.
Change-Id: I24b721eb436d17afd234002ae82f9166d2fcf65d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3580
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The vendor and part name from coreboot is normally stored in these
SMBIOS structure fields, but it can be useful to override them.
On Lenovo ThinkPads an override is e.g. needed to convince the Linux
thinkpad_acpi.c driver that it is actually running on a ThinkPad.
Change-Id: I0dfe38b9f6f99b3376f1547412ecc97c2f7aff2b
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1556
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This is needed for the Linux thinkpad_acpi.c driver to load.
Change-Id: I3d9549395556ffb0abfc3cb52b3d01386c34caa5
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3731
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This version is taken from arch/arm/lib/memmove.S in the Linux kernel.
Change-Id: Ic875d0cf5b1cb407606530b7f465c406b134f0fa
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is from memcpy_32.c in the Linux kernel. There was no copyright header
in the original file either.
Change-Id: Ifd259cb8a87615dce79ed1e551cc4bacb0414b4f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I4b6a57e7d8e7e685c609b1d85368585b9dd197dc
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
mainboard_enable() is now modelled after google/parrot where the
enable function only sets dev->ops->init for the root device to
point to a mainboard_init() function, which in turn is called in a
later pass over the device tree to do the actual initialization.
Change-Id: Iaf9187532a1e432b991260201b95dda85cc312c5
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3619
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The options that keep track of whether there are arch versions of the standard
string functions shouldn't be in the arch/x86 directory since they apply to
all architectures. Move them into the higher level, shared Kconfig defaulting
to off. Then, in each applicable arch (currently all of them) they can be
selected to on.
Change-Id: I7ea64a583230fdc28773f17fd7cc23e0f0a5f3d6
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some kernel assembly code uses a W macro to optionally add a .w to
instructions that need to be 32 bit thumb. The gnu assembler doesn't seem to
need the .w and won't assemble if it's provided.
Change-Id: I0a288177788b5c61810ee7bd3d2debea66835de2
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
With EARLY_CBMEM_INIT and CAR_MIGRATION selected, cbmemc_reinit()
was called twice during romstage. This effectively deleted output
of romstage in CBMEM console.
Change-Id: I21072a319c0e4a5f695b0573bc017bf7921fc663
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3609
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Split PCI IO configuration and MMIO configuration cycles to separate
files. Modern hardware does not use IO cycles for PCI configuration
after initial setup in bootblock.
Note that the pci_mmio_ and pcie_ functions were different in masking
the alignment for register address. PCI standard requires that 16-bit
and 32-bit configuration register writes do not cross boundaries.
Change-Id: Ie6441283e1a033b4b395e972c18c31277f973897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3554
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
PCI bus operations are static through the ramstage, and should be
initialized from the very beginning. For all the replaced instances,
there is no MMCONF_SUPPORT nor MMCONF_SUPPORT_DEFAULT selected for
the northbridge, so these continue to use PCI IO config access.
Change-Id: I658abd4a02aa70ad4c9273568eb5560c6e572fb1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3607
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Routes IRQs for USB device, SPI1, MOTOR, HD audio, CAN bus.
Change-Id: I995a5c6d3ed6a7dca4f0d21545c928132ccbbc21
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3725
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Store EHCI Debug Port runtime variables in CAR_GLOBAL.
For platforms without CAR_MIGRATION, logging on EHCI Debug Port is
temporarily lost when CAR is torn down at end of romstage.
On model_2065x and model_206ax ehci_debug_info was overlapping the MRC
variable region and additionally migration used incorrect size for
the structure.
Change-Id: I5e6c613b8a4b1dda43d5b69bd437753108760fca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3475
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There are other uses for EHCI debug port besides console, so move
EHCI relocation code from console to lib.
Change-Id: I95cddd31be529351d9ec68f14782cc3cbe08c617
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3626
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move ehci_debug_info allocation from console to lib, as console code
was only built for ramstage.
Implement dbgp_ehci_info() to return the EHCI context. Alread alias this
as dbgp_console_input() and _output() to return the console stream context
later on.
Change-Id: Id6cc07d62953f0466df61eeb159e22b0e3287d4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3625
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Output to usbdebug console needs to be disabled until hardware is
initialized and while EHCI BAR is relocated. Add separate field
ehci_info to point to back to EHCI context when hardware is ready
to transfer data.
Change-Id: If7d441b561819ab8ae23ed9f3f320f7742ed231e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3624
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The display port bridge on pit is different from the one on snow and needs to
be initialized differently. Instead of waiting for the chip to come up on its
own and assert the hotplug detect, we need to access it over i2c and get it up
and running ourselves.
Change-Id: I4bc911cb8e4463edff7beabd2f356cb70ae9f507
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3723
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This driver is basically the same as the one in U-Boot but without the device
tree stuff. That driver is, in turn, a straightforward implementation of the
sequence of register writes described in the data sheet. Comments were added
in U-Boot which helpfully describe what the register writes are actually
doing and are kept.
Change-Id: I64ba6b373478853bb2120f0553a43de901170d02
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/3753
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Data is intended to be a byte array, so it should be described by a type which
has a fixed size equal to an 8 bit byte. Also, the data passed to write
shouldn't be modified and can be const.
Change-Id: I6466303d962998f6c37c2d4006a39c2d79a235c1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3721
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was removed from ramstage a little while ago and should have been removed
from here as well.
Change-Id: I6a40ed4a98bedac39e5492e4b1aed3427ab4e08b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3720
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This appears to be needed, though we have no way to test yet.
Change-Id: I39033581011e056258193f2cdff78814361a8d55
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3719
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In resume path, if memory setup takes too long without setting PS_HOLD, EC watch
dog may power off or reboot the system. To prevent that, we should enable
PS_HOLD in same timing as cold boot - right before starting memory setup.
Change-Id: I5c294fa7ae015f8cff57b1fd81e5b80902647b15
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3718
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which manipulated the tps65090 were removed a while ago because
it isn't accessible directly from the AP, it's on an I2C bus that has to be
accessed by the EC on our behalf. Now that that capability has been added, we
can rewrite the small portion of the the tps65090 we actually used but using
the EC passthrough commands.
Also, we should not be configuring the hardware display port hotplug detect
line since we're using it as a GPIO for other purposes. The GPIO we're using
instead defaults to being an input, but to be safe we should probably
explicitly configure it as one anyway.
Change-Id: I7f8a8a767e3cccb813513940a5feceea482982f5
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3717
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ChromeOS EC for peach_pit is connected to SPI2 bus, not I2C.
Change-Id: Ifeb8a626aa4fc3d3a181a7bc016e3f91be948ae5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3716
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The workaround of re-opening device in exynos_spi_read has been fixed by the new
correct open/close and xfer procedure. It's safe to be removed now.
Change-Id: I6b1bf717c916903999a137998a578b0a866829bd
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3715
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switch spi_xfer and exynos_spi_read to use the new spi_rx_tx function.
Change-Id: I01ab43509df1319672bec30dd111f98001d655d0
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3714
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SPI driver (exynos_spi_rx_tx) was implemented with only "read" ability and
only full-duplex mode. To communicate with devices like ChromeOS EC, we need
both output (tx) and half-duplex (searching frame header) features.
This commit adds a spi_rx_tx that can handle all cases we need.
Change-Id: I6aba3839eb0711d49c143dc0620245c0dfe782d8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3713
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The original Exynos SPI open/close procedure was copied from U-Boot SPL with
some assumptions that only works in SPL stage. For example, it tries to always
work in 4-byte transmission mode with only RX data is swapped, and claims a
packet for initial address command (and with incorrect size).
This commit revises open/close and reset so only the required SPI registers are
configured.
Change-Id: Ieba1f03d80a8949c39a6658218831ded39853744
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3712
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fill the SPI device parameters for spi_setup_slave on Exynos 5420.
Change-Id: I10b4b9e6cfe46d7bfa34e80e3727c7e7da99ba9d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3711
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SPI module in Exynos 5420 didn't follow Coreboot's SPI API standard
(spi-generic.h) and will be a problem when we want to share SPI drivers.
This commit replaces exynos_spi_* by spi_* functions.
Note, exynos_spi_read is kept and changed to a static function because its usage
is different from the standard API "spi_xfer".
Change-Id: I6de301bc6b46a09f87b0336c60247fedbe844ca3
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3710
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove unused header and constant definition in SPI module.
Change-Id: I339e603f48186e4a356e83518b0d0b4c907f11b8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3709
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add SPI0 and SPI2 to Exynos 5 SPI list, and correct structure names.
Also removed the un-enumerated devices (SPI_BASE, base_spi()).
Change-Id: Ica6d9a41f9619c8c61eab664d5e988dd4a428e09
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3708
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For devices with ChromeOS EC on SPI bus, use the standard SPI driver interface
(see spi-generic.h) to exchange data.
Note: Only EC protocol v3 is supported for SPI bus.
Change-Id: Ia8dcdecd125a2bd7424d0c7560e046b6d6988a03
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3751
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the new Chrome EC protocol version 3 to Coreboot.
Note, protocol version 3 is not applied on any bus implementations yet.
LPC (x86) and I2C (arm/snow) are still using v2 protocol. The first one to use
v3 protocol will be SPI bus (arm/pit). LPC / I2C will be updated to v3 only
when they are ready to change.
Change-Id: I3006435295fb509c6351afbb97de0fcedcb1d8c4
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3750
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since EC protocol v3, the packet format will be the same for all buses (inclding
I2C, SPI, and LPC). That will simplify the implementation in each individual bus
driver source file.
To prepare for that, we will move the protocol part into crosec_proto.c:
crosec_command_proto, with bus driver in callback "crosec_io".
Change-Id: I9ccd19a57a182899dd1ef1cd90598679c1546295
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3749
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Embedded Controller (EC) for Pit is connected via SPI2, and needs to be
configured before we can talk to it.
Change-Id: I1f8e921b4616f15951f3e5fae1ecbf116de4ba90
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3707
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some initialization / shutdown commands should be paired correctly in a SPI I/O
session. For example, setting CS should be enabled and disabled in each read;
and the bus width (byte or word) should be configured only when opening /
closing the SPI device.
Change-Id: Ie56b1c3a6df7d542f7ea8f1193ac435987f937ba
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3706
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4feabc448945c4664d3114c0c8afdad48338230a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3705
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which checked the status of a transfer would return success if
the bus was no longer occupied, even if it's no longer occupied because the
transfer failed. This change modifies those functions to return three possible
values, 0 if the transfer isn't done, -1 if there was a fault, and 1 if the
transaction completed successfully.
Change-Id: Idcc5fdf73cab3c3ece0e96f14113a216db289e05
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The exynos manual suggests hooking the mmc ip blocks to the mpll. They had
been set to use a different pll. This changes them over and modifies the
divider so that the frequency stays the same.
Change-Id: I85103388d6cc2c63d1ca004654fc08fcc8929962
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3703
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows us to set different speeds for each HSI2C bus.
Change-Id: I50cc257aad9ef50025d0837b0516940b956efc02
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3701
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adjusts some clock settings so that they match U-Boot. There are
three different changes.
1. Change the source for psgen from the oscillator clock to the pclk.
2. Change the pll feeding the SPI busses from epll to mpll, as suggested in
the manual.
3. Change the SPI prescaller.
Change-Id: Ib54a255bc14fc286629dac86db9b8cf8e75a610b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3700
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The clock divider was being read from registers incorrectly which meant that
the periph rate was wrong.
Change-Id: I50efb62849ef29bdfb0efc56c49642d3edca094c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3699
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Wait for UART FIFO to be ready.
(Credit to dhendrix for finding the bits to test with.)
Change-Id: Ib6733e422cbc1c61b942bd90d85f88a3f412d6ff
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3698
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Chrome EC protocol V3 has several new command structure and constants defined.
Simply cherry-picking changes from upstream.
Change-Id: I7cb61d3b632ff32743e4fa312e0cc691c1c4c663
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3748
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
(forward ported from https://gerrit.chromium.org/gerrit/#/c/55554)
Change-Id: I5a20864689efd0c0149775e6d85b658e0cc6715c
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3697
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
Change-Id: I7eb19003c9e96efb5fa7a3f97c7b15f3ef332687
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I5cddffc2e524aae7a31a8f94f67e03a5b7e15c82
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3695
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Otherwise we have to worry about hand off between bootblock and
romstage. Too much complexity
Change-Id: I89bf8a229dba7e1330accadf9a732d831ebc4827
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3694
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is already called in ARMv7 bootblock_simple.c so we don't
want to do it twice
Change-Id: I80cb41035b8a77787e04f2ea58a1cd372cea97d8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I6b28bb95c7decbe3eed33b5b5a029bee48bbe403
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently, the exception handling code on ARM turns on alignment checks as an
easy way to generate an exception for testing purposes. It was leaving it on
which disabled unaligned accesses for other, unlreated code running later.
This change adjusts the code so the original value of the alignment bit is
restored after the test exception.
Change-Id: Id8d035a05175f9fb13de547ab4aa5496d681d30c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The GPIOs used by vboot and setting up the display and backlight were still
the ones for snow. This change updates them so they're correct for pit.
Change-Id: I06ba773da3af249efec723bb90c2e9e8075a777a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MAX_CPUS option is only used on x86 currently, so there's no reason to
have it in the pit config.
Change-Id: I270bbfd3aff781d88304791b1d9735777643caab
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3688
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
That part isn't used on pit.
Change-Id: I48f3a10f7e6eb89b1e9630d2372b6865b4c12a7f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3687
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On pit, the tps65090 is connected to the EC and has to be accessed by proxy.
Until we have that implemented, this change removes calls to tps69050 which
will never succeed, and stops compiling in the driver.
Change-Id: I7218f85f9f26623bd13aaaf8ded0638b3b2f874a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3686
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The members data structures in dmc.h are intended to have a particular size.
Rather than assume that particular types are the right size, we should use
types that are guaranteed to be the right size. Also, since the registers are
at particular offsets as well, the structures should be packed.
Change-Id: I9cc11d7451f92ba3eb85c6be88ecbc62c7a5652d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3685
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The previous driver was a bit awkward and not entirely correct. This change
primarily replaces the read/write functions with simpler and more robust
(hopefully) version.
Change-Id: I55f0ad8faec2de520e27577bd6dad9c0118d8171
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For all other CPUs, we unconditionally include the CPU Kconfig
files in the CPU directory, not in the vendor directory. Do the
same thing for the Exynos CPUs. This allows us to make CPU dependent
changes in the directory of that CPU alone.
Also, drop some unused Kconfig variables from the Exynos Kconfig
files.
Change-Id: I4e4c22a0693988834e619dd33d121bf994ed57e8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3683
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The dmb should be executed before reading operations, and before/after writing
operations.
Change-Id: I572136a2f9a07eb2c38a112f5deeb2de0c0fd46c
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3682
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the low-level I2C code to handle the new high-speed
HSI2C/USI inteface. It also outputs a bit more error information
when things go wrong. Also adds some more error prints. Timeouts
really need to be noted.
In hsi2c_wait_for_irq, order the delay so that we do an initial
sleep first to avoid an early-test that was kicking us out of the
test too soon. We got to the test before the hardware was ready
for us. Finally, test clearing the interrupt status register every time
we wait for it on the write. Works.
Change-Id: I69500eedad58ae0c6405164fbeee89b6a4c6ec6c
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3681
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the setup_power() function to actually set up the PMIC
which is on this board (the MAX77802).
Change-Id: I9c6f21f183dacc0bca71277e681e670834412d78
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3680
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds register offsets and important values for the Maxim
MAX77802 PMIC.
Change-Id: I3724b82bcb235b6684d2b976876f628f1ffbed3f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3747
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We saw a problem on x86 last year in which setting direction, then value,
glitched the output and caused problems. Change this code to set the output,
then the direction.
Change-Id: I3e1e17ffe82ae270eea539530368a58c6cfe0ebe
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3679
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The 5420 clock code still had a data structure in it for the 5250 clock
registers which was used by some of the clock functions. That caused some
clocks to be configured incorrectly, specifically the i2c clock which was
running at about 80KHz instead of about 600KHz as configured by U-Boot.
Also, the registers and bit positions used to set up the SPI bus were not
consistent with U-Boot, and if the bus clock rate were set to 50MHz, a rate
which has historically worked on snow, loading would fail. With these fixes
the clock rate can be set to 50MHz and the device boots as much as is
expected. I haven't yet measured the actual frequency of the bus to verify
that it's now being calculated correctly.
Change-Id: Id53448fcb6d186bddb3f889c84ba267135dfbc00
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3678
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested and working. Gets us to ramstage.
Change-Id: Ib9ea4a6c912e8152246aaf4f1f084a4aa1626053
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds entries for I2C8-10 to giant switch statement in
clock_get_periph_rate(). It also eliminates the I2C peripheral's
usage of clk_bit_info since it's confusing and error-prone.
Change-Id: I30dfc4c9a03fbf16d08e44e074189fb9021edb6d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3676
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code has been there for quite a while but was never enabled.
Change-Id: I4ec3dcbb3c03805ac5c75872614e5d394df667cf
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3675
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The pinmux code for the exynos5250 was all bundled into a single, large
function which contained a switch statement that would set up the pins for
different peripherals within the SOC. There was also a "flags" parameter, the
meaning of which, if any, depended on which peripheral was being set up.
There are several problems with that approach. First, the code is inefficient
in both time and space. The caller knows which peripheral it wants to set up,
but that information is encoded in a constant which has to be unpacked within
the function before any action can be taken. If there were a function per
peripheral, that information would be implicit. Also, the compiler and linker
are forced to include the entire function with all its cases even if most of
them are never called. If each peripheral was a function, the unused ones
could be garbage collected.
Second, it would be possible to try to set up a peripheral which that function
doesn't know about, so there has to be additional error checking/handling. If
each peripheral had a function, the fact that there was a function to call at
all would imply that the call would be understood.
Third, the flags parameter is fairly opaque, usually doesn't do anything, and
sometimes has to have multiple values embedded in it. By having separate
functions, you can have only the parameters you actually want, give them
names that make sense, and pass in values directly.
Fourth, having one giant function pretends to be a generic, portable API, but
in reality, the only way it's useful is to call it with constants which are
specific to a particular implementation of that API. It's highly unlikely that
a bit of code will need to set up a peripheral but have no idea what that
peripheral actually is.
Call sights for the prior pinmux API have been updated. Also, pinmux
initialization within the i2c driver was moved to be in the board setup code
where it really probably belongs. The function block that implements the I2C
controller may be shared between multiple SOCs (and in fact is), and those
SOCs may have different pinmuxes (which they do).
Other places this same sort of change can be made are the pinmux code for the
5420, and the clock configuration code for both the 5250 and the 5420.
Change-Id: Ie9133a895e0dd861cb06a6d5f995b8770b6dc8cf
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3673
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The memset and memcpy functions are assembled as ARM code, likely because
that's the default of the assembler. Without special annotation, the assembler
and linker don't know that those symbols are functions which need special
handling so that ARM/thumb issues are handled properly. This change adds that
annotation which gets those functions working in Coreboot which is compiled as
thumb. Libpayload and depthcharge are compiled as ARM so they don't *need* the
annotation since it just works out in ARM mode, but it's the safe thing to do
in case we change that in the future.
We should explicitly select ARM vs. thumb when assembling assembly files to be
consistent across builds and toolchains.
Change-Id: I814b137064cf46ae9e2744ff6c223b695dc1ef01
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3672
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It might be that you want an early console in romstage before RAM is up, but
you can't or don't want to support the console all the way back in the
bootblock. By making the console in those two different environments
configurable seperately that becomes possible.
On the 5250 console output as early as the bootblock works, but on the 5420 it
only starts working in the ROM stage after clocks have been initialized.
Change-Id: I68ae3fcb4d828fa8a328a30001c23c81a4423bb8
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3671
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5420. Don't
always print all of them per default.
Change-Id: I2152ab760e31a335dbcd9d6ad32cd1eaae4b89bc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3670
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
remove some unused code
Change-Id: I41602fb391c1910c588a4f9dcc7c2edefe8ab5bc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3669
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If we clear the framebuffer and then flush it back to memory using cache
operations, the writes are going to be full cachelines at a time. If we
make it uncacheable first, the writes will be serialized writes of
whatever sized chunks memset uses, probably 4 bytes or less.
Change-Id: I960f87a370e97f9e91236ad796d931573bb3dbb8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3668
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At one time it seemed to be necessary to disable and then re-enable the
MMU when setting the framebuffer to be uncache-able due to bugs in the
MMU management code. Since those bugs have been fixed, this is no longer
necessary.
Change-Id: I7ce825cf5eaaa95119364d780cba0935752e4632
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/3667
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already
known when that structure was put together. Eliminate the extra space,
and pass the single value instead of the structure.
Change-Id: I29bc17488539dbe695908e47f0b80c07e102e17d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/3666
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code which figured out the rate of the input clock to a peripheral was
doing several things wrong. First, it was using the wrong values when
determing what the source of a clock was set to. Second, it was using the
wrong offset into that register to find the current source setting.
This change fixes the constants which select a clock source which get some
more things working, but doesn't attempt to fix the bit position table.
Change-Id: Id7482ee1c78cec274353bae3ce2dccb84705c66a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3665
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Not all ARM systems need "BL1", and the layout of BL* and bootblock may be
different (ex, Exynos 5250 may use a new BL1 with variable length checksum
header).
To support that better, define the real base address (and ROM offset) of boot
block, and then we can post-processing ROM image file by filling data / checksum
and any other information.
Change-Id: I0e3105e52500b6b457371ad33a9aa546acf28928
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3664
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On x86 there is a 16-byte alignment requirement for the
addresses containing the CPU microcode. The cbfs files
containing the microcode are used in memory-mapped fashion
when loading new mircocode. Therefore, the data payload's
address/offset of a cbfs file in flash dictates the resulting
alignment. Fix this by processing the CPU microcode cbfs
file separately as it uses $(CBFSTOOL) to find the proper
location within the provided rom image.
Change-Id: Ia200d62dbcf7ff1fa59598654718a0b7e178ca4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The LPC-based ChromeOS EC uses several ioport regions to communicate with
the AP. In order for the new unified userspace access method to work, we
need them to be reserved by the BIOS.
Before /proc/ioports shows:
0800-0803
0804-08ff
We'd like just a single 256-byte region at 0x800, but ASL can't handle that.
So this will work:
0800-087f
0880-08ff
Change-Id: I3f8060bff32d3a49f1488b26830ae26b83dab79d
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: http://review.coreboot.org/3746
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5250. Don't
always print all of them per default.
Change-Id: Ie349f2a4117883302b743027ed13cc9705b804f8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3661
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Chrome EC still does not tolerate SERIRQ in quiet mode
and so the keyboard does not work properly.
Change-Id: I9ab052187c9926ce0e2c86b86dfe987dd6564c1b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/3745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Now that we are executing VbInit() in coreboot we can end up
in a situation where the recovery reason is consumed during
VbInit (end of romstage) and then the EC is rebooted to RO
during ramstage EC init, thereby losing the recovery reason.
Two possiblities are to remove the EC check+reboot from ramstage
and let it happen in depthcharge. This however means that the
system has to boot all the way into depthcharge and then reboot
the EC and the system again.
Instead if we do a check in romstage before VbInit() is called
then we can reboot the EC into RO early and avoid booting all
the way to depthcharge first.
This change adds a ramstage version the EC init function and
calls it from the shared romstage code immediately after the
PCH decode windows are setup.
Change-Id: I30d2a0c7131b8e4ec30c63eea36944ec111a8fba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/3744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This stuff is not used, so let's drop it.
Change-Id: I671a5e87855b4c59622cafacdefe466ab3d70143
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3660
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With only 19 source files it doesn't make a whole lot of sense to
create sub directories in arch/armv7, especially since the files
were distributed somewhat randomly.
Change-Id: I029c7848e915edf1737e1c401c034837c95d179d
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3659
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new code is stolen from U-Boot with little or no understanding of how it
works.
Change-Id: I3de7d25174072f6068d9d4fdaa308c0462296737
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This function had been declared in a public header file, but was marked
static when actually defined.
Change-Id: Ia551a5a12e7dbaf7bc00861e085695145ab7b91a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3657
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Don't initialize console twice in the bootblock
- remove printk in memory init that would mess up the UART
- unconditionally run console_init() in romstage, as it is
also unconditionally run in the bootblock.
Change-Id: I983d011c6ca602445f447d17799c1b2a33e8bd1d
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With LynxPoint-LP the SCI GPE is no longer a GPIO
that is offset by 16. Remove the Add and fix up
the link definition so it is still accurate.
Change-Id: I091141183a09345b5ffe28365583e48019f9f5e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/3742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If we clear the framebuffer and then flush it back to memory using cache
operations, the writes are going to be full cachelines at a time. If we make
it uncacheable first, the writes will be serialized writes of whatever sized
chunks memset uses, probably 4 bytes or less.
Change-Id: I1b81731cfed00ae091ba6357451ab186d16f559e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At one time it seemed to be necessary to disable and then re-enable the MMU
when setting the framebuffer to be uncache-able due to bugs in the MMU
management code. Since those bugs have been fixed, this is no longer
necessary.
Change-Id: I5f7b9bd14dc9929efe1834ec9a258d388b8c94e9
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3654
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When modifying the page tables, use writel to ensure the writes happen, flush
the page tables themselves to ensure they're visible to the MMU if it doesn't
look at the caches, and invalidate the right TLB entries.
The first two changes are probably safer but may not be strictly necessary.
The third change is necessary because we were invalidating the TLB using i
which was in megabytes but using an instruction that expects an address in
bytes.
One symptom of this problem was that the framebuffer, which was supposed to be
marked uncacheable, was only being partially updated since some of the updates
were still in the cache. With this change the graphics show up correctly.
Change-Id: I5475df29690371459b0d37a304eebc62f81dd76b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3653
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already known
when that structure was put together. Eliminate the extra space, and pass the
single value instead of the structure.
Change-Id: Ia6a41cefdf8b29fe7d68f9596a156eced6eb5df8
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3652
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Coreboot knows that, for the snow board, certain pins are to be connected to
bus controllers in the SOC and to the wires of a bus external to the SOC. It
can configure them as such and free its payload from having to know how to
set everything up.
Change-Id: I1bb127c810e9ee077afc4227a6f316eaa53d6498
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3650
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Change-Id: I53a40d114aa2da76398c5b97443d4096809dcf36
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3730
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I1fef27c4a16ee4358ace8014a8d6e9fa92c4f790
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3728
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ifea10f0180c0c4b684030a168402a95fadf1a9db
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3727
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The page tables need to be aligned to a 16KB boundary and are 16KB in size.
The CBMEM allocator only guarantees 512 byte alignment, so to make sure
things are where they're supposed to be, the code was allocating extra space
and then adjusting the pointer upwards. Unfortunately, it was adding the size
of the table to the pointer first, then aligning it. Since it allocated twice
the space of the table, this had the effect of moving past the first table
size region of bytes, and then aligning upwards, pushing the end of the table
out of the space allocated for it.
You can get away with this if you push things you don't care about off the
end, and it happened to be the case that we were allocating a color map we
weren't using at the start of the next part of cbmem.
Change-Id: I6b196fc573801b02f27f2e667acbf06163266651
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3651
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These pins will be driven by the internal controller which shouldn't have pull
ups or downs in the pin fighting with them.
Change-Id: I579aed84ace45d8f5f1d3ca64c064d98de842b57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3649
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Guard console_init() with CONFIG_EARLY_CONSOLE in bootblock
- Don't initialize console twice in the bootblock
- remove printk in memory init that would mess up the UART
- unconditionally run console_init() in romstage, as it is
also unconditionally run in the bootblock.
Change-Id: I8f0d60877433162367074d0e55e01f935fd81f8e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3647
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adds a pit mainboard which is mostly a copy of snow, except that
mentions of the 5250 were replaced with the 5420, and mentions of snow were
replaced with pit.
Change-Id: I8eb0ce379eb2fa353bb88d5656a0c5e2290afbf0
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some of the settings which were defaulted to or automatically selected for the
exynos5420 which were inherited from the exynos5250 were not correct for this
SOC.
Change-Id: I11ffd8a6b80628405ac493fe2139f79c05d15d7e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3645
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change creates an exynos5420 directory with code that will eventually
implement support for the exynos5420 cpu from Samsung. Currently it's a copy
of the exynos5250 directory with the name changed. There are going to be some
problems where headers in src/cpu/samsung/exynos-common include headers in the
exynos5250 directory directly.
Change-Id: Ia8d7244310d32499238bbc171c0c668ec48178e1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Exynos GPIO code has three different APIs that, unfortunately,
were widely used throughout the code base. This patch is cleaning
up the mess.
Change-Id: I09ccc7819fb892dbace9693c786dacc62f3f8eac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3643
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When starting the Exynos5250 port, a lot of unneeded u-boot code
was imported. This is an attempt to get rid of a lot of unneeded
code before the port is used as a basis for further ARM ports.
There is a lot more that can be done, including cleaning up the
5250's Kconfig file.
Change-Id: I2d88676c436eea4b21bcb62f40018af9fabb3016
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3642
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ice28114e5f53f510d305cd85d095044e2f4bd7b2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3740
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
The enumeration results are stored as five DWORDs in one 20 byte buffer.
Bytes 3, 7, 11 and 15 were used to set the lowest bit of each DWORD.
ACPI uses little endian, so 1, 4, 8 and 12 are the correct indices.
Change-Id: I793225cb1bb62fd148ecfa1e61e02f5d7be62cdb
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3602
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It turns out that the exynos5-common code previously imported from
u-boot is not common code at all but very specific to the 5250 and
not compatible with the 5450. Hence, unify the directories exynos5250
and exynos5-common. We will try to factor out common code while
progressing with the 5450 port.
Change-Id: Iab595e66fcd01eda8365c96fb8bef896f7602f03
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3641
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch unfortunately incorporates a number of changes,
all of which are making future ARM ports easier.
- drop cruft that came in with u-boot
- move serial console from mainboard Kconfig to Exynos Kconfig
- factor out non-board specific wakeup code
- move generic bootblock code from mainboard to Exynos
- actually call arch_cpu_init()
- remove dead code
- fix up copyright messages
- remove snow_ prefix from a lot of code to reduce the noise
when creating a new mainboard based on that code.
Change-Id: Ic05326edf5a7e1a691c5ff841a604cb9e351b562
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3640
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... and drop the wrapper on ARMv7
Change-Id: If3ffe953cee9e61d4dcbb38f4e5e2ca74b628ccc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3639
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In ram stage, all code flow should be tied to the resource allocator.
Stuff that has to happen before everything else goes into the mainboard
enable function in mainboard.c. This patch empties the main() wrapper
around hardwaremain.c, allowing to get rid of this special case in the
ARM port.
Change-Id: Ide91a23f1043b64acf64471f180a2297f0f40d97
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3638
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We've got enough of a handle on this to realize some things:
drm_dp_helper.h is by design device and architecture independent
i915.h is common to most intel graphics chipsets going back several years
i915_reg.h is as well
Move these files to src/include/device, and adjust the .c files accordingly.
Change-Id: I07512b3695fea0b22949074b467986420783d62a
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3637
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add three functions to edid.c:
void set_vbe_mode_info_valid(struct edid *edid, uintptr_t fb_addr)
takes an edid and uintptr_t, and fills in a static lb_framebuffer struct
as well as setting the static vbe_valid to 1 unless some problem
is found in the edid. The intent here is that this could be called from
the native graphics setup code on both ARM and x86.
int vbe_mode_info_valid(void)
returns value of the static vbe_valid.
void fill_lb_framebuffer(struct lb_framebuffer *framebuffer)
copies the static edid_fb to lb_framebuffer.
There is now a common vbe.h in src/include, removed the two special ones.
In general, graphics in coreboot is a mess, but graphics is always a
mess. We don't have a clean way to try two different ways to turn on
a device and use the one that works. One battle at a time. Overall,
things are much better.
The best part: this code would also work for ARM, which also uses EDID.
Change-Id: Id23eb61498b331d44ab064b8fb4cb10f07cff7f3
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The default for this variable should be n, it should only depend on
EC_GOOGLE_CHROMEEC, and it should be (and is) explicitly enabled when
needed. This prevents it from being turned on when the EC bus is SPI.
Change-Id: Idc6651a764be4f055341a36b9b4a58990f050b0c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3737
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Define at one place whether to use IO 0xcf8/0xcfc or MMIO via
MMCONF_BASE_ADDRESS for PCI configuration access funtions in ramstage.
The implementation of pci_default_config() always returned with
pci_cf8_conf1. This means any PCI configuration access that did
not target bus 0 used PCI IO config operations, if PCI MMIO config
was not explicitly requested.
Change-Id: I3b04f570fe88d022cd60dde8bb98e76bd00fe612
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3606
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Without that fix, and with CONFIG_SMM_TSEG, we have:
src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep':
src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1
The fix is modelled after src/cpu/x86/smm/smihandler.c which
ifdefs smi_release_lock().
Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3281
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This mistake was spoted by comparison with the
src/southbridge/intel/bd82x6x/smihandler.c file.
Change-Id: I1516f0131d524bd7d001e6780e9a45402d1814d1
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3303
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an option to mark all SPI regions write protected on each S3 resume.
We were used to lock the SPI interface in the payload which isn't run on
the resume path. So we have to do it here.
For the write protection to be effective, all write opcodes in the
opmenu have to be marked correctly (as write operations) and the whole
SPI interface has to be locked. Both is already done.
Change-Id: I5c268ae8850642f5e82f18c28c71cf1ae248dbff
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3594
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This code is the initial version of FUI for haswell and wtm2.
The code is simplified from before in many ways. I've gotten rid of
the opcode table, because it obscured meaning and I don't think it is
needed any more. Register sets, mainly used for reset, are just lines
of code -- not many of them. There are a bunch of not-yet-documented
registers here; the VBIOS seemed to think they were necessary and
testing shows they seem to be right.
As a bit of added paranoia, we always include the VBIOS code as our
emergency recovery path. You have to run it now anyways, so this is no
regression from our current situation; and, if all goes well, in a
week (or so), you'll never have to run it again, but like the Force
and nose hair, it will be with you always.
The code can return in three ways. The first, best way is success:
panel is up and the VBIOS need not run. The second mode is that we
tried to light up the panel but could not, for some reason, but will
return with the panel partly up. In this case, it's ok not to power
cycle the panel. The third, worst case, which will NEVER happen, ha
ha, is that we have to turn the panel off and wait the required 600ms
for it to cycle. Life sucks sometimes. This failure mode is in the
'hang on we're going to fix it' category now that we have ramstage in
RW.
The Big Goal here is to create something other coreboot ports can use
as well. The guys doing the x60 report that the link FUI works,
without too many mods, on that chipset, so it seems Intel is keeping
things from changing too much over time.
Also, again, please note: this and the next 3 versions will ALWAYS fail.
The goal is to verify the correctness of the recovery path.
The bizarre tab-space formatting in drm_dp_helper.h is from the original,
as in i915_reg.h
Change-Id: I6ecf454633029d185c29d470980b5a0f3114a8ce
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3635
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This lights up the display. We don't get graphics but we are missing the gttsetup
at this point, so that is no shock. The real shock is that anything works at all.
Change-Id: I03fc470334e96878aeb8465044b3cc9c90378735
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3634
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch was started by Dave Hendricks and implements the procedure for
setting up the UART as described in the manual. Some unused code was removed.
Change-Id: If26a424cac401ef3eafaec081147f41184fbcee9
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3490
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The PnP's logical device activation normally resides at 0x30. This might
have been overlooked as 0x29 looks very close to 0x30 in human eyes.
Change-Id: Id5d5a92f2683ebe1808b943f686c062151d216da
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3592
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The enumeration method tried to evaluate an one-byte OperationRegion
instead of a field in this OperationRegion, which resulted in an
AE_TYPE error at runtime.
Indexing the OperationRegion with a single field fixes this error.
Change-Id: I15dd7aa6ecafb3a215d165d2b721003446815025
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change all PCI configuration accesses to MMIO on two boards
with i5000 chipset. To enable MMIO style access, add explicit
PCI IO config write in the bootblock.
Change-Id: I26f1c2da5ae98aeeda78bdcae0fb1e8c711a3586
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3601
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I missed the board with gm45 when I moved MMCONF_SUPPORT lines.
Also, the intel/i3100 does not have MMCONF_SUPPORT implemented
even though it was previously selected for intel/eagleheights board.
Change-Id: I9c7f6b0a150b4d54288a1e015277b9d98467fca4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3598
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change all PCI configuration accesses to MMIO on all boards
with SandyBridge and IvyBridge. To enable MMIO style access,
add explicit PCI IO config write in the bootblock.
Change-Id: I8f957a80bf57df000897c5a080dd5ff131b1ec0d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3576
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Move/remove MMCONF_SUPPORT reference under mainboard Kconfig, as
that feature originates from northbridge and cannot be disabled
for a single mainboard.
Change-Id: I6d6861079876ddddaff90b10f18edb6936e93bd0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3589
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The W83627DHG has some power managements bits to power down individual
logical devices. These are called `* Power Down`. Counterintuitively and
in contrast to `Immediate Power Down` (bit to power down the whole chip),
these bits are set when the respective logical device is powered.
Unfortunately, our ACPI code set them wrong which led to disabled
devices after a S3 suspend/resume. Adding an option how to set the PM
bits and setting them to zero for the W83627DHG, corrects it.
Tested with kontron/ktqm77.
Change-Id: I8a472d480d4277721bd17c9f7c2ce44fa84e8ae2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3590
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use the same indentation, comment placement and spelling of words.
Run `indent -linux …`.
Change-Id: Id5765c45b28058cdd50ee4c0a1fd9f645ad7f3f8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3220
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The MAX_PIRQ_LINKS is defined in src/Kconfig with a default value
of 4. The src/northbridge/via/vx900/Kconfig also defines
MAX_PIRQ_LINKS with a default of 8 and it ends up giving us
a value of 8 for non-VIA platforms.
Change-Id: Iee1938d38a93ab7c35c8cb6fe9656a92cf3fa21e
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3586
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add comments in PAR0._PRS explaining which dependent resource
descriptor puts the parallel port into EPP or SPP mode.
Change-Id: If4e224dbaf6f9105cde88d995d2e7c74fbf14502
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3495
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Set up the pinmux to enable the pins and the clocks for whichever UART is
currently configured.
Change-Id: Iac13f16d9d84320555b99734ea83eafd0a2803fe
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3573
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The pinmux register data structure describes a subset of the control module
registers, but the address which pointed to the base of the pinmux registers
was actually being set to the beginning of all the control module registers,
not just those having to do with the pinmux. With this address fixed, the UART
now works on the beaglebone black.
Change-Id: I7c99b6f37d7da359af074127cd0c1a86fda2d9a0
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3574
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All the additional work that needs to be done in EHCI BAR relocation
is independent of the hardware platform and was functionally identical
in all the copies removed.
When USBDEBUG is not selected, PCI EHCI controllers use standard
pci_dev_read_resources() call.
With USBDEBUG selected, PCI EHCI controller's device_operations
.read_resources is replaced with pci_ehci_read_resources() call,
which in turn will replace the device_operations .set_resources call.
The replacement for .set_resources reconfigures usbdebug driver side,
and calls the original .set_resources to configure hardware side.
Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3412
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch is based on 'AMD S3: Program the flash in a bigger data packet'[1]
Some AMD south bridge can write bigger data when saving S3 info.
In this patch, I use config 'AMD_SB_SPI_TX_LEN' to contral data size.
AMD_SB_SPI_TX_LEN is defined in 'src/southbridge/amd/Kconfig'
and then can be overridden in the Kconfig for specific
southbridges that support larger size.
I have tested on AMD Parmer and Thatcher. We will release a new board
whose south bridge can transfer more than 4 bytes each time.
[1] http://review.coreboot.org/#/c/2306/
Change-Id: Id984955d46eae487e39d45979f1a90054aa9f54b
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3413
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Without that fix we have:
src/drivers/elog/elog.c: In function 'elog_is_header_valid':
src/drivers/elog/elog.c:213:3: error: format '%u' expects argument of type 'unsigned int', but argument 4 has type 'long unsigned int' [-Werror=format]
Change-Id: I71b80a94c03a04eedb688ae107d92c05a878315e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3551
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Thanks to Bruce's great work, we can finally drop this workaround.
Change-Id: Ie92d1e53ef867fa34aa2489ccfb682d73195b213
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3569
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Users of mptable_write_buses() pass two pass-by-reference
parameters reflecting a maximum bus number and a search bus
number. These bus numbers are expected to be held in "int"
variables and are updated by the function. Both of the
Supermicro boards define the search bus number as a
byte value in mptable.c.
For now, change the two Supermicro boards to use "int"
to hold the search bus index.
Change-Id: Ie71850719c1fa3cda0ac9c8773bb80650de95c70
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3546
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix a bunch of compiler-generated warning messages. These fixes are
mainly braces for grouping initializers. These changes are not
intended to change any code functionality. There are two changes where
function prototypes are added, and two cases where unused variables are
eliminated.
Change-Id: I93cef8899170b5575e7fb7c55181b381a7bcd9d8
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3545
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The existing code for setting Azalia configuration assumes that
the configuration bits are contiguous within a single byte and
can be set using a byte copy addressed into the lowest 2-bit
subfield.
The fix in Family 14 defines a union that can be addressed as a
byte to overlay the bit fields. Since the offset of the four
subfields is not necessarily fixed, change the code to initialize
each of the four subfields individually.
Change-Id: I1dff20bb8bd3e1bcd8b4e6b0537e20779d2a3521
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Copy a type cast from the other cases of the same switch statement
to eliminate compiler warning messages.
Change-Id: I8d0a88892f6a5f8e43227ab5f830041894b07f6a
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3543
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On Dinar, H8SCM, and H8QGI, add <cpu/amd/amdfam15.h> as an
include to pick up the prototype definition of get_bus_conf().
Change-Id: Ie4887670ac52aa194745881362df19cd1d75773e
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3542
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change inserts a type cast to eliminate a compiler warning.
Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3541
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change replaces a redefinition of NULL with the standard
definition from <stddef.h> to eliminate a compiler redefinition
warning.
Change-Id: I441fa569f545c0efb00284b5ee58aa27cb6617ba
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3540
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change eliminates an unused variable that causes a build warning.
Change-Id: I02487c7dd80d458f562d7afe1827eefcc0fb678b
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3526
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This requires a new system agent binary (v6 / v11 on haswell).
Note that the existing system agent binaries are long time obsolete
and won't work with current coreboot, so this update is overdue.
Change-Id: I48d8649576ca84d2b85ab082ce06f3462e189059
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3568
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
Change-Id: I3d43acaf64e2e2d9717421cb547fec35e582cf8b
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change is mostly type casts to eliminate compile time
warnings. These specific changes are mostly cherry-picked from
AMD Family 14 code and, as such, contain artifacts copied over
from F14. For example, there are a number of UINT64 casts that
are commented out rather than removed. This is to maintain
consistency between AGESA versions. Ultimately, this is in
preparation for turning on warnings as errors for AMD Family 15
server parts.
Change-Id: Ic73d0b6ebab18d97015a9dd1130aff4e5e432fb7
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3525
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This reverts commit d358a506c4http://review.coreboot.org/#/c/3514/ comments:
The pei_data version changed to 6, so new binaries are needed.
However, demand for new binary blob is not referenced with this commit nor is git submodules hash updated. Also the new binary blob almost doubles its size and no longer fits in the allocation sandybridge defines.
Change-Id: I84eb70517d5b9278c611fdfa587a71f6ca0f657f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3553
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The xHCI controller's MMIO space has a length of 64KiB not 4KiB.
Therefore, setting the xHCI BAR to 0xe8001000 worked the same like
setting it to 0xe8000000, as bit12 is reserved and ignored. This again
interfered with the MMIO space of the first EHCI controller and broke
S3 resume on Ivy Bridge.
AFAIK, the MRC ignores the setting of the xHCI BAR, anyway. So just drop
these lines.
Change-Id: I8af9c2ba34133f15636a9056fc8880b3b6ab95e0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3521
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
BIOS write protects 8 bytes of CMOS, which nvramtool can't cope with.
This makes initial installation harder, so just mark those as reserved
to work around the issue.
Change-Id: I210861dff8572e226a0f250556a3b811671ea8f2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3531
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
6021 is Vortex86DX northbridge PCI device ID, not for Vortex86EX.
Change-Id: I9bea799c9033adbcfacc8ad47052280a32f9ee59
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3529
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Current build configuration always wants to include an Intel Management
Engine firmware (me.bin) on Sandy Bridge systems. However, we can have
a working coreboot without it, as long as the factory delivered ME
firmware is kept untouched in the flash ROM. So let the user decide if
a ME firmware will be included in the build.
Change-Id: I9a1cc29d4940ba22355eb9e653606e436f07e04c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3522
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
For iwave/iWRainbowG6 using intel/sch, MMCONF_BASE_ADDRESS was unused
and different from hardware setting. Change that to match hardware
programming.
Change-Id: I3324b7ea0e6f092206d4b6b791476d538e826657
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3507
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
On newer Intel systems, the flash ROM is shared between the host
processor (BIOS), it's Management Engine (ME) and an integrated ethernet
controller (GbE). The layout of the flash ROM (and other information) is
kept in the so called Intel Firmware Descriptor (IFD). If we only want
to build coreboot to update the BIOS section, all we need is the flash
layout.
This patch adds the option to specify the flash layout in the
mainboard's Kconfig, and thus, to build without the real IFD. However,
with such a build, one has to make sure that the IFD section on the
flash ROM won't be written over (nor any other section that hasn't been
included by coreboot). A patch to write selected sections of a flash ROM
with IFD has been sent to the flashrom mailing list [1].
[1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html
Change-Id: Ia23e439a00a197fb54852263f8e206f16c3e8851
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3524
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are no files to build left under AMD nortbridge/x/root_complex
directories. For some cases, even the Kconfig file was no longer sourced.
Remove all such references and empty files.
For devicetree.cb treat component paths with "/root_complex" in them valid
even when the directory does not exists. This is because AMD boards us this
dummy chip component as the root node in their devicetree.cb.
The generated devicetree file static.c remains unchanged.
Change-Id: I9278ebb50a83cebbf149b06afb5669899a8e4d0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3434
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The IOMMU needs IRQs assigned. So add those.
Change-Id: Ic9f02e28aac593cddf7d222a8abb780a10572d32
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3318
Tested-by: build bot (Jenkins)
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The IOMMU AGESA needs a reserved scratch space and it wants
to allocate the stuff for runtime. So provide a simple
allocator for 4 KB CBMEM page.
Change-Id: I53bdfcd2cd69f84fbfbc6edea53a051f516c05cc
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3315
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
