Some type-c monitors do not immediately assert HPD. If we continue
to boot without HPD asserted, Depthcharge fails to show pictures
on a monitor even if HPD is asserted later.
Also, if an HDMI monitor is connected, no wait is needed. If only
an HDMI monitor is connected, currently the API always loops until
the stopwatch expires.
This patch will make the AP skip DisplayPort wait loop if it detects
an HDMI monitor. And if an HDMI monitor is not detected, the AP will
wait for DisplayPort mode (like before) but also its HPD signal.
This patch also extends the wait loop time-out to 3 seconds.
BUG=b:72387533
BRANCH=none
TEST=Verify firmware screen is displayed even when a type-c monitor
does not immediately assert HPD. Verify if HDMI monitor is connected,
AP does not wait (and firmware screen is displayed on HDMI monitor).
Change-Id: I0e1afdffbebf4caf35bbb792e7f4637fae89fa49
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/23816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The GPIO pins for UART 0 on Fizz are routed to the add-in card slot
and should not be used as a UART device. coreboot is setting the
pins to GPIO Mode but FSP is re-configuring them for Native Mode
and the behavior is unexpected when the kernel tries to initialize
the UART device.
The UART 0 device is PCI function 0 so it needs to be enabled for
other functions to be visible to the OS so it can't just be disabled.
Instead, set the device to PchSerialIoSkipInit so that FSP will not
change the pin state.
BUG=b:73006317
TEST=Tested with add-in card on fizz hardware to ensure the pin state
does not change when FSP runs or the kernel boots.
Change-Id: Id97c1e482ef0d5642fcf9018d802e1d0e073263d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This reverts commit 2e81f394cf, as it will
have side effect that will make system shutdown failure. System will not
enter S5 sleep state, instead a global reset will be generated.
Once camera driver ACPI framework ready, isclk programing will be moved
into APCI method, in _PS3, isclk will be turned off to save power.
BUG=b.72532565
BRANH=master
TEST=Apply the changes and flash coreboot, on meowth devices, issue
"halt" in OS stage, system can shutdown successfully.
Change-Id: If35697911f97c524d9b52bdf4dae5c9ef1cc8618
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25006
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support for variants to use secondary SPD if
required. This enables a variant to have different types of memory
supported using the same image.
BUG=b:73514687
Change-Id: I3add65ead99c510f2d6ec899fbf2cb9a06c79b0c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Similar to Soraka, this change sets the pch_trip_temp value to
75C. This is important so that PMC can shutdown the thermal sensor
when CPU is in C-state and DTS temp <= pch_trip_temp.
BUG=b:74089135
Change-Id: Ic46fa0681796b821dfb014ab91734c960df7846a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Commit d2d2aef6a3 (sb/intel/{bd82x6,ibexpeak}: Move RCBA macros to a
common location) makes some platforms use the wrong OIC register defi-
nition. It was extended to 16-bit in the corporate version of ICH10.
So let's give the new size and location a new name: EOIC (extended OIC).
This only touches the systems affected by the mentioned change. Other
platforms still need to be adapted before they can use the common RCBA
definitions.
Change-Id: If9e554c072f01412164dc35e0b09272142e3796f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/24924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Turn on pcie ports 9,10. Enable Root Port 9 and set up clkreq 3.
BUG=b:72120814
TEST: Boot to OS via NVMe
Change-Id: I272b63b11e6b00ae5bdbef5a37ee517cc0636f6d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/23208
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2760p: enable PCIe
8470p: enable mSATA
8460p: enable PCIe, also add comments according to circuit diagram
2570p: comment for some USB ports
Change-Id: Ib5209f2dfb249fca5bae89bc6da3b704c8e903dd
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/23357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Intel DCI (direct connect interface) allows debug Intel target using
USB3.0 ports. It will support debug via USB stack (DCI Dbc) using USB3.0
only.
BUG=None
TEST=Turn on DCI trace hub in descriptor.bin and flash the coreboot
image. Using DAL to halt/run CPU.
Change-Id: I39e68dabfcb9e659733019334299e562eee3681d
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
If switch to VT2 on nautilus, screen flicker appears. We found if we
rollback the change of slew rate setting, then the flicker issue will
be gone: https://review.coreboot.org/c/coreboot/+/22588
But nautilus board needs slew rate tuning to reduce EE noise, so we
decided to change only SlowSlewRateForSa to 2 (Fast/8) instead of
rollback the whole change of the CL:22588. It can remove the flicker on
VT2.
BUG=b:71397040
BRANCH=master
TEST=emerge-nautilus coreboot
Change-Id: Id1d4bd8b1316c02c783de708ec4658e030193a26
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/23877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Due to there are some chances USB devices can not be detected.
USB2 port#1 and #4 PHY register need to be overridden for variants
Santa/Lava/Blue/Bruce/Astronaut.
port#1:
PERPORTPETXISET = 4
PERPORTTXISET = 4
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
port#4:
PERPORTPETXISET = 7
PERPORTTXISET = 7
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
BUG=b:72623892
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: I401905685cc3078df657919b162272c3de320296
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/23881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The GPIOs for PCIe reset and power enable for WLAN must be set up before
amdinitearly for wlan to function.
BUG=b:73898539
TEST=Boot, see WLAN controller in lspci
Change-Id: I568a3240a54817ab6dcf15fe39f7f1336943852b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/24916
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- consolidate commonality in meowth and zoombini's SPD makefiles into
a common zoombini/spd/Makefile.inc
- move all SPD hex files into zoombini/spd directory
- move SPD_SOURCES definitions to variants/$(VARIANT_DIR)/Makefile.inc
BUG=b:69011806,b:71776625
BRANCH=master
TEST=Verify 'emerge-meowth coreboot' and 'emerge-zoombini coreboot'
compile and boot successfully.
Change-Id: I2291ebaf0ef5da1b22eb0e8fa7af8dbb50848c29
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23874
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Many generations of Intel hardware have identical code concerning the
RCBA.
Change-Id: I33ec6801b115c0d64de1d2a0dc5d439186f3580a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Coverity scan has found an error where a NULL pointer is dereferenced.
The bug would happen if the devicetree does not contain a valid entry
for PCA9538. In this case the code
* if (dev->path.i2c.device == PCA9538_SLAVE_ADR)
would dereference to a NULL pointer.
This patch fixes this issue. Thanks coverity!
Found-by: Coverity (CID 1386126: Null pointer dereferences (REVERSE_INULL))
Change-Id: I75e271d86c16fa3938420c43575ebba910f6a2fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Our CFM daughter card would like to use individual PCIe lanes for two
different devices on the card.
dlaurie@ has reconfigured PCIe port 9-12 from 1x4 to 1x2 + 2x1 on b2b
connector on fizz to meet the requirement:
https://chrome-internal-review.googlesource.com/571936
We also need to enable the ports on device tree.
BUG=b:72523836
TEST=none
BRANCH=fizz
Change-Id: Icded9850d833752680e0174b6c476e657817b319
Reviewed-on: https://chromium-review.googlesource.com/923867
Commit-Ready: Zhongze Hu <frankhu@google.com>
Tested-by: Zhongze Hu <frankhu@google.com>
Reviewed-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/924860
Commit-Queue: Shelley Chen <shchen@chromium.org>
Tested-by: Shelley Chen <shchen@chromium.org>
Signed-off-by: Zhongze Hu <frankhu@chromium.org>
Reviewed-on: https://review.coreboot.org/23845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
While programming interrupts, a message "perhaps this device was defined
wrong?" shows up twice. This is caused because some devices have
interrupt programmed for APIC mode, but not for non-APIC mode. Fix
mainboard_picr_data table by identifying devices programmed with value
0x1F while programmed differently on mainboard_intr_data table. Do so
only for devices that are used by kahlee or interrupt required by old OS.
BUG=b:70788755
TEST=Build and run kahlee, Verify that message disappears from serial
output.
Change-Id: Ic285036290519ed3ee617dffa616bd26c61575c5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This commit uses newly defined macros to make it easier to read which
iomux function pads are being configured to use.
TEST=Booted grunt, confirmed display backlight came on.
BUG=b:72875858
Change-Id: I24e5091fc7ef696f8e9c932ce04664e6cc3ccb90
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There's no need to set the output enable here; this is already handled
by the native function. I'm making this correction in this change to
prevent the GPIO pin descriptions from getting confusing.
BUG=b:72875858
TEST=Booted, confirmed S5_MUX_CTRL high with and without this change.
Change-Id: I9e047be7169586c59892ef2bdab915683feeebda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Turn on PCH iSCLK for meowth platform.
BUG=None
TEST=Boot up into OS and check register programming with iotools, the
command is iotools mmio_read32 0xfdad8000, returned value is 0x03.
Change-Id: I1e44e3748c9b37c8f60adcc47a866d445d77cfaa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23368
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The EC builds for nyan_big, peach_pit, and smaug (ryu) have been removed
from the latest EC codebase, so don't try to build them by default
anymore.
Change-Id: I53901b32753c5b9b050f517bbf3f10b9071913d4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For variants that have a cr50 tpm, this enables faster polling when
interacting with the tpm.
BUG=b:72838769
BRANCH=none
TEST=verified on grunt that irq is used and not timeouts for tpm
Change-Id: I5786d334b6c1cc70f4c7107c75b07a7e27ac4428
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds the Pmax setting in device tree. The Pmax is from
MAX(PL4_sku1, PL4_sku2, ..) + ROPmax. Given ROPmax is 30W and
the maximum PL4 is from U42, hence the Pmax = 71W + 30W = 101W.
BUG=b:72138778
BRANCH=None
TEST=USE=fw_debug emerge-nami chromeos-mrc coreboot chromeos-bootimage
& ensure the Pmax value is passed to FSP-S.
Change-Id: Ief6a134dc5b6bd2b8e07b4a44450e99ff26402d9
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AmdInitPost returns AGESA_WARNING. This is because AGESA by default
enables bank interleaving, while the HW does not meet the requirements
for it. Disable bank interleaving, thus clearing AGESA_WARNING.
BUG=b:73118857
TEST= Build and run kahlee. Search for "agesawrapper_amdinitpost()
returned AGESA_SUCCESS".
Change-Id: Ice9270f9b10051dbb622344919223cf5439f5d7b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Based on the pictures at http://www.fit-pc.com/web/products/intense-pc/,
the Intense PC does not look like a laptop. In its documentation it is
described as "mini-PC" or "Single Board Computer".
This patches moves the Intense-PC into the correct category on the
Supported Motherboards page.
Due to thermal considerations, I have not removed the "select
SYSTEM_TYPE_LAPTOP" in Kconfig.
Fixes: de7f8d3a19 ("mainboard/compulab: add support for CompuLab Intense-PC")
Change-Id: I4343306a2f82eed8211981cbd3b084f5d112d30b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
... and fix them in the process.
The Kconfig help text seems to be a slightly better place for such
documentation than a comment in Kconfig.
Change-Id: I4114e17ad9c486a9de059040b0e2821540c31aad
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fizz fails to show pictures on a type-c monitor because VBIOS runs
before DisplayPort link is ready.
With this patch, when firmware needs to display something, Fizz calls
google_chromeec_wait_for_display to make sure display is ready.
The penalty is up to 2 sec per boot in dev and rec boot. Normal boot
won't affected unless there is EC update.
BUG=b:72387533
BRANCH=none
TEST=Verify screens are displayed on Fizz as follows:
1. Put DUT in normal mode
2. Flash EC image to trigger EC sync (critical update)
3. Trigger manual recovery (insert)
4. Hit ctrl+d to switch to dev mode (to-dev)
5. Confirm to reboot (dev warning)
6. Warm reboot (dev warning)
7. Cold reboot (dev warning)
8. Flash EC image to trigger EC sync (critical update)
9. Trigger manual recovery (insert)
Change-Id: I90befe94f93e13904987acda50b2598d034b0031
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/23746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This makes the flow for GPIO initialization more closely follow that
what is performed for other boards so that it's easier to read the flow
(and stops relying on BS_WRITE_TABLES).
BUG=b:72875858
TEST=Built and booted grunt, built gardenia.
Change-Id: Ic97db96581a69798b193a6bdeb93644f6a74fc9d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23679
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Soraka, Poppy & Nautilus are designed to operate at max power of
45 Watt. Hence set psys_max to 45W.
BUG=b:66066340
BRANCH=None
TEST=Build and boot soraka.
Change-Id: If6f624733830b462329b5f539c20e2aea664143e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/23757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
The board does no support eMMC so no need to configure it.
Change-Id: If29009a09f39484b1da16fb650b4f9cbee2a6d19
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The board does not have memory down, only 2 DDR4 Slots.
Change-Id: I70eda83fbce7a707da170c7e555ed1a6dc6b1f4a
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Enable the micro-controller interrupt line as a real IRQ.
BUG=b:71986991
BRANCH=none
TEST=on Meowth, run 'ectool --name=cros_fp fpmode capture' and see the
number of interrupts incrementing and the MKBP event happening.
Change-Id: Ic0cf03d2a3508148b6482a5a595eaa213eff52c7
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Turns out the write-protect GPIO polarity for Scarlet is different than
for Kevin/Gru, and nobody ever told us. Also, it must not be configured
with an internal pull-up or we'll not read the correct value. This patch
fixes both issues.
BRANCH=scarlet
BUG=b:73356326
TEST=Booted Scarlet, confirmed that crossystem wpsw_boot returns the
right value in all cases.
Change-Id: Idd348ecdf9da8fff7201b83e869ba097b8570f32
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/23767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change enables DPTF and configures the policy. DPTF parameters were
provided by internal power team.
BUG=b:67877437
BRANCH=master
TEST=emerge-nautilus coreboot
Change-Id: I31b31d5282ab38278bc68045ce75fdc6192f1144
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/23731
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Read cse file was not getting cached and taking about 500ms on every boot.
Change-Id: I8c92eefc64fe146c628d9c104d7dfb016204004c
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/23743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Show mainboard version in the console log so that one can easily see it.
Change-Id: I33bae8b340fce13c0cbe525521828929038b069a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The I/O expander on the mc_bdx1 is used to get the hardware version of
the mainboard. This patch enables the chip driver for the I/O expander.
Change-Id: I98c667fe4dccf0698ab4cb5ede6082f020c70ec6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This format (one hex digit, followed by 'b', followed by binary digits)
is arguably useful, but also confusing. Use the more common format
instead.
Change-Id: Ide7b0a999483a2dd863a70f8aa42cd0865e2babf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Original SPD provided by the vendor had bytes after 254 shifted by 16
bytes. This change fixes the SPD data based on the latest details
received from the vendor.
BUG=b:72749394
TEST=Verified that the device with this memory part boots to OS fine.
Also, mosys is able to dump the right memory information.
Change-Id: I6938dea761c5785048aad69eeeaf50e2d0fa8ca1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Previously, we were seeing device boot into the recovery screen with
error code 0x5a. This was root caused to the SATA GPIOs (specifically
DEVSLP) not being initialized early enough, causing the SATA 1 link
detection to time out and the device to reboot into recovery with
0x5a instead of booting into the OS as usual.
BUG=b:69715162
BRANCH=None
TEST=after flashing BIOS, set gbb flags to 0, then type reboot from
the OS.
Change-Id: I53913d5b7adaeb43edd0ef2d24a7cad92052d68a
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change makes the Nautilus platform update the two fields:
*oem_id* and *oem_table_id*, if the Maxim codec is detected.
Change is made to correct the audio topology file name that is
being read from oem_id fields, loaded and displayed in dmesg.
BUG=b:68686020
TEST=Build, booted nautilus board. Verified kernel reads new strings.
Change-Id: I041f2838f07a2525be7a28fdc69b7f1af46d16f1
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/23648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Previously ECT was disabled in commit 22401, on D0 stepping system and
FSP version 7.x.20.52, disabling ECT will cause memory training failure
and the system is stuck at post code 00D5h.
BUG=b.72473063
TEST=Apply patch and build coreboot image, flash into meowth P0 system
with D0 stepping silicon installed, system can pass memory training and
boot up into OS.
Change-Id: I7dd0a7dfe2993ad9cfaf00050175e5a47468b471
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This change makes Nami platform update the two fields:
*oem_id* and *oem_table_id*, if the Maxim codec is detected.
Change is made to correct the audio topology file name that is
being read from oem_id fields, loaded and displayed in dmesg.
BUG=b:70646770
TEST=Verify kernel reads new strings.
Change-Id: I513a997f312e2d37d76da0379feb017d1f591f9a
Signed-off-by: Kaiyen Chang <kaiyen.chang@intel.com>
Reviewed-on: https://review.coreboot.org/23670
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add support for KBL RVP8 board
* Add KBL RVP8 support in Konfig.
* Add KBL RVP8 config option in make menuconfig.
* Add descriptor and ME binary paths for RVP8 in Kconfig.
* Add RVP8 board name Kconfig.name.
* Add devicetree.cb for RVP8 in the variants path.
* Add gpio.h for RVP8 in variants/include/variant path.
TEST= Build and boot RVP8.
Change-Id: I6ba177c223f6aa3285c0fe5eba0cd55b2a50c4ed
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23383
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The Pmax is calcuated from MAX(Psku1, Psku2), where Psku1, Psku2 are
estimated Pmax power of U42 and U22 skus. For U42 sku, the Pmax is PL4
(71W) + ROPmax (49W) = 120W; for U22 SKU, the Pmax is PL4 (43W) +
ROPmax (49W) = 92W. So Pmax is set to MAX(120W, 92W) = 120W.
BUG=b:71594855
BRANCH=None
TEST=Make sure correct pmax value is being passed into fsp
Change-Id: Ic27fef87c869094b20438e6ee0e1eb0b35122b8d
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23633
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
CMOS layout is not used and can be removed. A change to Kconfig is needed in
order not to break the build.
BUG=b:64207749
TEST=Build gardenia.
Change-Id: I24a71490777b101b069175460f3715ec3ff78240
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change updates the WiFi device wake pin to GPP_E22 from WAKE# (to
match the latest schematic changes).
Since WiFi was the only device using WAKE# pin, DSX_EN_WAKE_PIN is
removed from deep_sx_config as well.
BUG=b:72697650
TEST=Verified:
1. Wake-on-wifi works.
2. Device is able to enter G3 without WAKE# pin causing unwanted wakes
from deep S5.
Change-Id: Ibde81f73cca322f9b8b45baf8ee18ae00521467d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With the new extra detachable UI elements, we're running out of space in
Scarlet's RO CBFS. Thankfully, the GBB is still massively
overdimensioned, so we can steal another half MB from there.
This patch changes the FMAP for some boards that have already had
production firmware releases. However, all the new changes are to the RO
parts of the FMAP, so there shouldn't be a way this could cause a
problem for updates.
Change-Id: Iec182de3e894e56fec2a64b034c0ca65d78a5522
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/23595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
I2C bus rise/fall times were measured as follows. Signals were generated
with:
- bus 0: manual i2c driver in depthcharge
- bus 2,3: i2cdetect -r <bus_number>
and then measured manually with an oscilloscope.
BUG=b:72442912
Change-Id: I291e144249271ec34a93417398e54e68b8e21e23
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
CMOS layout is not used and can be removed. A change to Kconfig is needed in
order not to break the build.
BUG=b:64207749
TEST=Build kahlee.
Change-Id: Ib5d18e80a56111d96c730420db865194c71de1b3
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add `cmos.default` to get rid of four seconds in romstage. Choose 8 MB
for size for video RAM.
Order the entries like in `cmos.layout`.
Change-Id: If2dcc266f6f061807401b62647124ce96e9a3802
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/23468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Enable HotPlug for the PCIe root port that the WiFi device
is on so the OS can re-train the link without needing a reboot
if it goes down unexpectedly at runtime.
BUG=b:72417777
TEST=enable HotPlug on Eve Root Port 0 (WiFi) and check in
linux that it is identified as a HotPlug capable root port.
Change-Id: Id2b7fc92c8c9128f0e28102eb5991bda7fbf6799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23512
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pass in fizz-specific adapter-based PsysPl3 and Pl4 values to avoid
brownouts. According to Intel doc #560604, page 74, the max time
window is 64ms (code=6) and the min duty cycle we can set is 4%.
BUG=b:71594855
BRANCH=None
TEST=Boot to OS and check MSRs using iotools for expected values
Change-Id: I06a4c5bc25f6ec036b79f6941f80e26058d64930
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
On EVT, the USB and MIPI cameras share the same power source. As a result,
when the MIPI camera driver turns off the camera once probed, USB camera will
be disconnected. To make USB camera work on EVT devices, we will need a hack in
coreboot to leave the camera power always-on.
BUG=b:72839352
TEST: Verified the MIPI and USB camera function on DUT board
TODO: This power issue will be fixed on DVT build. Will revert this patch
once confirmed power sources for MIPI and USB camera could be supplied
individually.
Change-Id: Icaaf7e17447492f2e2f2d03eb9a35bcc53667f28
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-on: https://review.coreboot.org/23546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andy Yeh
This patch makes coreboot fetch OEM ID and SKU ID from EC. If it fails,
it falls back to GPIO pins.
BUG=b:70294260
BRANCH=none
TEST=Verify AP log shows expected OEM ID and SKU ID on Fizz.
Change-Id: I06d3a205275b46660b3974bc3673d4be8e13f6d1
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/23548
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface.
BRANCH=none
BUG=none
TEST=Verify masks with ec hostevent command on S0, S3, S5 and S0ix. Also
check that lidclose/lidopen command from EC console wakes system up from
S3 or S0ix.
Change-Id: I60343aaa9e0ddfd38d42b6d0aa2820e2fd880fb7
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23453
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cherry-pick from Chromium:
a60ac10 [Lars: Turn on keyboard backlight in romstage]
Use the keyboard backlight to provide indication that the system is
booting. This is useful for determining that a system is in S0 and
is running BIOS code.
TEST=boot on Lars and see keyboard backlight come on early
Original-Change-Id: I4fede6cff85f4487cedfbccf6cc24c6380d905e0
Original-Signed-off-by: Jenny TC <jenny.tc@intel.com>
Original-Tested-by: Divagar Mohandass <divagar.mohandass@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I4b1fed10d9bd1ae1b265e848417836f816f252f3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Combination of several commits from Chromium tree:
949037c [Lars: coreboot GPIO changes for EVT]
c286789 [Lars: Set USB Type A current limit to 2A]
0f1b26d [lars: set BOOT BEEP GPIO GPP_F_23 to output and Low]
4a0650d [Lili: Support touchscreen]
Disable unused GPIOs based on schematic and
adds GPIO mappings for HSJ_MIC_DET, PCH_BUZZER and AUDIO_INT_WAK.
Set GPIOs USB_A0_ILIM_SEL & USB_A1_ILIM_SEL low to enable 2A
charging from the USB Type-A port.
GPP_F_23 is set to NC currently and is floating, causing the on-board
speaker to have no audio or the audio has noise; set to output/low.
These commits bring lars' GPIO mapping in line with the Chromium tree.
Original-Change-Id: I3bf4aa8599255e5382d99810b4c83b4c97c648b6
Original-Change-Id: I328a8be22dc59492477cbe362a5d5b94aa80a397
Original-Change-Id: I253e55bf2b423363a00347778cabaa4184d85aec
Original-Change-Id: I761f7c5ea5fc7a173c07a8c37da1338a1b2cd269
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Tested-by: Balaji Manigandan <balaji.manigandan@intel.com>
Original-Tested-by: Kuen Liu <kuen.liu@quantatw.com>
Change-Id: Ic2d188fbf913a11fbf6ad1f0eb3a5e72ba4cb1cf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium:
99cd8f8 [lars: Update the MAINBOARD_FAMILY string in Kconfig]
This string was left at the default for kunimitsu and should be
updated to indicate the proper mainboard.
Original-Change-Id: Icc0e162d57242e7b0610fb570ef1a8a45ee16e4f
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia4b70227c8cfdfe939e40ea6258d494337a2907b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Combination of several commits from Chromium tree:
3b875a2 [Lars: Update Memory ID for DVT board]
b6d7c63 [Lili: Update Memory IDs]
f203f99 [Lili: Add new SPD for Hynix H9CCNNN8GTALAR-NUD]
a6571bf [Lili: Update Memory IDs]
80e1841 [Lili: Update Memory IDs]
58d4487 [Lili: Fix memory string show error in spd data]
These commits bring lars' SPD data in line with the Chromium tree.
Original-Change-Id: I54d0e6d2bbe86d5dc2ee5825f332d36abfa99084
Original-Change-Id: I9431393f369a1d2870bdabba1fc55d9cefae5c39
Original-Change-Id: I3b325a1801f49109429eb647d8d98a5537ce1b7b
Original-Change-Id: Ie8a32d8a26ea1054e2df8432084a95d1cb03f991
Original-Change-Id: I64c73950e3bea57b6c5a90257211b3d6d7f1baab
Original-Change-Id: I0e425fa4f0bae544680d5522c2e05a4f7a3be95a
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Tested-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I7cc9b01012b0b9ed72804192bb5953243fc859b4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit:
af3ec09 [Lars: Add sdmode-delay device property for maxim98357a]
Add "sdmode-delay" as a device property for the maxim98357a codec.
This speaker amp requires both SFRM & BCLK to active and stable
before it is unmuted. If there is a BCLK and no SFRM,
that results in a pop noise.
Adding a configurable delay parameter for all Skylake platforms
to allow sufficient time for the BCLK & SFRM on I2S to be stable
before the amp unmutes itself to avoid a pop noise at the start of playback.
Setting the delay to 5ms since the observed delay between SFRM and unmuting
of the amp is around 2ms.
Adaptation needed to account for parameters having moved
from mainboard.asl to devicetree in upstream tree.
Original-Change-Id: I1fff4f86ff816e907553e7a6f1d05713f9d85084
Original-Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I8a1c52ccdb08df9a4ab293e12bb266309e08737b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit:
848ee3a [Lars: Add device properties for Nuvoton codec]
Update sar-threshold, sar-compare-time, sar-sampling-time
properties to match values in lars' Chromium branch.
Adaptation needed to account for parameters having moved
from mainboard.asl to devicetree in upstream tree.
Original-Change-Id: Id0c28e50406a29e6f33d04ca78fd2a3e3974fa90
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Benson Leung <bleung@chromium.org>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Change-Id: I2748a315d27eb947197109808b4d5fa8a82c8cf3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium:
55c0eb3 [Lili: Set new thermal parameters]
Set new parameters of DPTF for both Lars and Lili.
The acoustic will have higher 1.6dB in transition mode,
when using Lili fan table on Lars.
Original-Change-Id: I730ac483e2a6d43c8dcfe94da6761194c14f3163
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Change-Id: I3bf16db43bb90a542c6526f3bc891f820da00ca0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The wifi card was not being powered, and was being held in reset during
PCI enumeration, so it was not being brought up.
BUG=b:72738963
TEST=Verify wlan card shows up in lspci
Change-Id: I5a1e83298af35aa80c67c75cd6ec0a2c3213891e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23552
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is a line artifact in the lower third of the display with the
current initialization code. So update it with code provided by
Innolux to fix this issue.
BUG=b:69689064, b:72191820
TEST=boot on dru with an Innolux panel and artifact line disappear.
Change-Id: I9679c4f7f706fd6cd2e1dba7ec79e772fe3f227a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When booting kahlee, there's an error message: "Warning: Can't write PCI
IRQ assignments because 'mainboard_pirq_data' structure does not exist".
This is generated by write_pci_cfg_irqs due to missing mainboard_pirq_data.
BUG=b:70788755
TEST=Build and boot kahlee. Warning message must be gone.
Change-Id: If07d2f54f06f6cf77566c43eddc8ee8a314e7a3a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The kernel requires the display oprom is loaded *and* ran
in order for the kernel to not panic. Therefore, select the
correct settings such that normal mode works for Chrome OS.
BUG=b:72400950
Change-Id: Ibae5bc6b382cbe71a55c2386a24bb420cb8f313f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23506
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This commit adds an entry for H1/Cr50 into the devicetree for setting up
ACPI entries for H1 communication.
BUG=b:69250772
TEST=See probe messages in dmesg
Change-Id: Id55ce3364ea4acdb62782758e5bcb2a167286cb9
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23514
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This commit removes a manually written asl file in favor of configuring
the trackpad through devicetree.
BUG=b:72121803
TEST=cat /proc/interrupts with trackpad connected
Change-Id: I38afcf89ea64ffaf6a10bb317c41154feda57e50
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23508
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Now SOC code can select the require UDK support package for any
platform going forward with FSP2.0 model.
Change-Id: Ie6d1b9133892c59210a659ef0ad4b59ebf9f1e45
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Turn on power for front camera at startup in coreboot (needs
to be set for factory scan).
BUG=b:69011806
BRANCH=master
TEST=none
Change-Id: I2f31b19dfef5fe386b485dd675f0ff981288acf4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/23503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change GPIO settings for meowth rev 2 boards.
Changes include:
- GPP_B7 set to no-connect
- GPP_C1 set to no-connect
- GPP_D8 set to no-connect
- GPP_D9 (PP3300_WLAN_EN) set as output with initial value high
- GPP_E9 (DCI_CLK) set to no-connect
- GPP_E10 (DCI_DATA) set to no-connect
BUG=b:72202352
BRANCH=none
TEST=none
Change-Id: I2e6d049faaa0a70b40ceb47aaf81a81d820dd4c1
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set USB2 port 0 & 1 to use OC2 and OC3 respectively. Previous settings
were causing false overcurrent conditions as OC0 and OC1 were used for
other purposes.
Remove initialization of unused usb3 ports, and configure the ports we
use (usb3 ports 0 & 1) to use OC2 and OC3, respectively.
BUG=b:72250084
BRANCH=none
TEST=Verify meowth can recognize and boot off a kernel on USB drive.
Change-Id: I528b67d80a1da84e5307facb40de545089979f57
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change selects EC tablet event and provides trip point
temperatures for tablet and non-tablet mode so that DPTF can
be supported depending upon device mode.
BUG=b:65467566
TEST=Verified by changing modes that the trip point temperatures are
updated in the
OS (/sys/devices/virtual/thermal/thermal_zone{2,3,4,5}).
Change-Id: I071868982fa87821550b870a6d8050cf2a030b49
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23463
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This change decouples EC tablet event and TBMC device by guarding
TBMC definition and notification using EC_ENABLE_TBMC_DEVICE. It
allows mainboards to use tablet events without having to define a TBMC
device.
BUG=b:72554519
Change-Id: Ie38b6d68486e8e644dd0d6d406def3ae7fdb5152
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Since the h1 i2c bus is required for verstage mark the bus
as needing to be initialized early. That way, the bus is initialized
in bootblock prior to verstage.
BUG=b:70232394,b:69250772
Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Innolux didn't deliver a working init sequence yet for devices without
OTP programming. The sequence in this change has been derived from a
register dump of a mostly working panel with OTP. It is not meant to
be final, but to make devices with unprogrammed OTP work, while Innolux
is figuring out a proper sequence. There is a known issue with an
artifact line in the lower third of the display.
Change-Id: I7096506208e4cb29c5f31a7ac502231a6c23ac92
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some panels need to transfer initial code, and some of them will be
over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi
dsi transfer function to support it.
Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Set PsysPl2 values to 90% of max adapter power for all types of
adapters (typeC and barrel jack) to account for a 10% power loss from
the adapter to the soc.
BUG=b:71594855
BRANCH=None
TEST=reboot device and make sure Pl2 and PsysPl2 MSRs are properly set
with iotools rdmsr command on both U42 and U22 skus with both
typeC and barrel jack power adapters.
Change-Id: I8425c6d4d669449eccb9324ff58ff6d1662c5c43
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
I measured the rise and fall times for I2C bus 1 from userspace
manually, using "i2cdetect 1" called from userspace and an oscilloscope.
This commit fixes the values there to reflect reality.
BUG=b:72442912,b:70232394
Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23459
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change updates the camera power enable GPIOs as per the latest
schematics. With this update, since one of the enable GPIOs is using a
UART0 pin, set UART0 to PchSerialIoSkipInit in devicetree so that
FSP-S does not re-configure the UART0 GPIOs.
BUG=b:68964831
Change-Id: I5d9126ed8ca2b714f6276f4d3a24c243d7654774
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This commit adds support for an Elan touchscreen device connected over
I2C via devicetree.
BUG=b:72121803
TEST=Confirm the device is probed for.
Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
I2C bus configuration is generally set up in devicetree.cb. This change
establishes listings for the buses so that they can be used (though
followup changes should update the buses to have correct timings).
BUG=b:72121803
Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is required to add support for I2C devices on Kahlee to ACPI tables
via devicetree.cb. Without this, operations are not emitted for I2C
devices and the proper ACPI table entries are not generated.
BUG=b:72121803
Change-Id: I1cfe12f3cc23e90ec74b739678f5a5a73257c2c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Chrome OS reports that "GRUNT TEST XXXX" is an invalid hwid. The 8296
comes from the lower four numbers from running:
$ printf "%d\n" 0x$(crc32 <(echo -n 'GRUNT TEST'))
BUG=b:72436450
Change-Id: Ib0044442396cad65c25c107feb35a30a2f70b769
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23411
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This change disables SATA controller in order to make SATA IP enter
low power status.
BUG=b:72332817
TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
and verify SATA IP enters low power state
Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add config option SOC_ESPI in glkrvp Kconfig. This is to disable LPC
and enable eSPI instead.
TEST=Boot to OS
Change-Id: I3116b656d41d1d7719c254888d1e3640628a97ca
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Audio DMIC_DATA needs to be ON in S0ix to support Wake on Voice.
By doing this, SoC can see the DMIC DATA and use for WoV processing.
Thus configuring GPIO_173 as IGNORE IOSSTATE.
TEST=put DUT in S0ix, verify DUT wakes up
Change-Id: I8bf403564e927deb8fed7f415e334bb230107cb0
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23246
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[] with data
from agesa_board_gpios[], wrap format and delete agesa_board_gpios[].
Finally, make platform_FchParams_reset() an empty function.
BUG=b:64140392
TEST=Build gardenia.
Change-Id: Id2ea63656a7d2f20f55fc5a4c75457db85b80cbd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This patch removes IccMax settings from device tree since they
are handled in SoC code from patch e1a75d.
BUG=b:71369428
BRANCH=None
TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot
chromeos-bootimage" & ensure the IccMax settings passed
to FSP are from SoC code.
Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Turn on the load switch to the FP MCU at startup, so the kernel can
detect it and use it.
The load switch enable pin is connected to the GPP_A11 PCH pin (aka
PCH_FP_PWR_EN).
BRANCH=none
BUG=b:71986991
TEST=on Meowth, see the kernel detecting a cros_fp device at startup:
[ 2.133456] cros-ec-spi spi-PRP0001:00: Fingerprint MCU detected.
[ 2.157420] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Change-Id: Id3c40b965a5f018c63481c2e2eea3fc8307352bd
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure the FP MCU interface on GSPI1.
BRANCH=none
BUG=b:71986991
TEST=boot on reworked Meowth with a ZerbleBarn board attached to
GSPI1 and see the cros_ec kernel driver detecting it.
Change-Id: Ib874ddaf4948a766fd05c11f4675dbfdb679059d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The variable t32 was originally used to do bitwise operations, but it is
not required anymore. Also, it was assigned twice accidentally, which
introduced a new Coverity Scan defect.
Found-by: Coverity (CID 1385126: (UNUSED_VALUE))
Change-Id: I77afd5064304a36991f63cf1328e13820144efb6
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
Mainboards:
src/mainboard/a-trend/atc-6220
src/mainboard/a-trend/atc-6240
src/mainboard/abit/be6-ii_v2_0
src/mainboard/azza/pt-6ibd
src/mainboard/biostar/m6tba
src/mainboard/compaq/deskpro_en_sff_p600
src/mainboard/gigabyte/ga-6bxc
src/mainboard/gigabyte/ga-6bxe
src/mainboard/msi/ms6119
src/mainboard/msi/ms6147
src/mainboard/msi/ms6156
src/mainboard/nokia/ip530
src/mainboard/soyo/sy-6ba-plus-iii
src/mainboard/tyan/s1846
Change-Id: Id895963f9641bcaaa65e8a8cb21213a758a9ad80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23301
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i82810
Mainboards:
src/mainboard/asus/mew-am
src/mainboard/asus/mew-vm
src/mainboard/ecs/p6iwp-fe
src/mainboard/hp/e_vectra_p2706t
src/mainboard/intel/d810e2cb
src/mainboard/mitac/6513wu
src/mainboard/msi/ms6178
src/mainboard/nec/powermate2000
Change-Id: Ib273316c59f499e6cd3a0e4c4dc4c2cce94ff291
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23300
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for new memory stuffing options that will appear on
the P1 meowth boards.
new strap setting - associated SPD file
----------------------------------------
0b001 - Hynix_H9HCNNN8KUMLHR_1GB.spd.hex
0b010 - Samsung_K4F6E3S4HM_2GB.spd.hex
0b011 - Hynix_H9HCNNNCPUMLHR_4GB.spd.hex
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: Ief07f3de351d01cbc195b785c36e96de0cbf7ddb
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Our current U22 skus (celeron and i3) actually don't support PL2,
but making sure that if we do decide in the future to use it to
make sure PL2 and PsysPl2 values are set appropriately.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 90W with barrel jack for U42
and 65W with barrel jack for U22.
Change-Id: I084d0320128a6e05948023520a30c497c41be23b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change the directory of the included cpu.asl file. This board seems to
have been omitted in 0a4e0fd "Fix the PNOT ACPI method".
Change-Id: Idc00197b1544006299e720dca59e02f6bf8f683c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23308
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
Change-Id: I65173104fce258d03956bbb0e80073c47fe80fab
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The PNOT method never notifies the CPU to update it's _CST methods due
to reliance on inexisting variable (PDCx).
Add a method in the speedstep ssdt generator to notify all available
CPU nodes and hook this up in this file.
The cpu.asl file is moved to cpu/intel/speedstep/acpi since it now
relies on code generated in the speedstep ssdt generator. CPUs not
using the speedstep code never included this PNOT method so this is
a logical place for this code to be.
Change-Id: Ie2ba5e07b401d6f7c80c31f2bfcd9ef3ac0c1ad1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Right now the poppy baseboard camera topology allows to add maximum of 2
sensors. The sensors can be of different vendors. The current ASL code
structure doesn't allow sensor customization. Moving PMIC specific objects
from sensor objects to PMIC scope and having separate sensor ASL files will
help in unbinding the PMIC and sensor objects and allow some customizations.
BUG=None
BRANCH=None
TEST=Build and boot soraka, make sure both camera's are working fine
and also verify that the generated DSDT looks fine.
Change-Id: I63ae1a685b78bda212c5c48a4c2dc744164a3cb5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The variant boards can have a custom endpoints, splitting the ASL code
aids customizing the endpoints as per the variant board setup.
BUG=None
BRANCH=None
TEST=build boot soraka, verify that the cameras are working fine and
generated DSDT tables are same as before.
Change-Id: I5f1cded25bfb6a7baf18b211f9773dfecdc2f264
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Boards that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
Removed boards:
amd/dinar
tyan/s2886
supermicro/h8scm
supermicro/h8qgi
Change-Id: I16be3b43fc0c48d58ed8b6667880c9571c6f5510
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
cpu/intel/socket_mFCBGA479
northbridge/intel/i82830
Mainboards:
mainboard/rca/rm4100
mainboard/thomson/ip1000
Change-Id: I9574179516c30bb0d6a29741254293c2cc6f12e9
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i3100
southbridge/intel/i3100
superio/intel/i3100
cpu/intel/socket_mPGA479M
Mainboards:
mainboard/intel/truxton
mainboard/intel/mtarvon
mainboard/intel/truxton
Change-Id: Ic2bbdc8ceb3ba0359c120cf4286b0c5b7dc653bb
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i5000
Mainboards:
mainboard/supermicro/x7db8
mainboard/asus/dsbf
Change-Id: I6614c0033b4439d196f26819998d3f85e6d11c00
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i855
Mainboards:
mainboard/lanner/em8510
Change-Id: Ic9ba0ba7e2b6e602a5749cc531dd705c49e3f08d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
soc/intel/sch
Mainboards:
mainboard/iwave/iWRainbowG6
Change-Id: Ida0570988a23fd0d13c6fcbe54f94ab0668c9eae
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
soc/dmp/vortex86ex
Mainboards:
mainboard/dmp/vortex86ex
Change-Id: Iee7b6005cc2964b2346aaf4dbd9b2d2112b7403f
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
cpu/amd/geode_gx2
northbridge/amd/gx2
southbridge/amd/cs5535
Mainboards:
mainboard/amd/rumba
mainboard/lippert/frontrunner
mainboard/wyse/s50
Change-Id: I81c130f53bbfa001edbfdb7a878ef115757f620c
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some Dock events only need to happen based on the Dock Id (which
functions as a presence detect GPIO).
Inspired by vendor bios DSDT.
This fixes undock ACPI events being issued when pulling out the power
when docked or undocked (but still generates one when forcibly
undocked)
Tested on X200: pull power and see if undock events are generated in
dmesg.
Change-Id: I1eef971d49508bcd94d5d1cf2b70395b7cd80b1c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This source file was mostly copied from ga-945gcm-s2l but had
different IO decode ranges.
Change-Id: I54cb165000fad6984edf13fb33519fb9c9f0350f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Things cleaned up in this patch:
* Add macros for the GENx_DEC registers;
* replace many magic numbers by macros;
* remove many writes to DxxIP since they were 'setting' reset default
values;
* fix some comments about decode ranges.
Change-Id: I9d6a0ff3d391947f611a2f3c65684f4ee57bc263
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add code to support the board ASUS AM1I-A. Tested with multiple payloads
and OSes with satisfactory results. S3 suspend/resume works fine with
Linux but has issues with Windows (an exception is thrown). However,
after manually rebooting, Windows resumes the suspended session.
* Tested with: SeaBIOS 1.11 + Linux 4.10 - OK
* Tested with: tianocore vEDK2017 + MS Windows 8.1 - OK
* Tested with: FILO 0.6.0 - hangs after showing the banner
Details are going to be published on the board's status page.
Change-Id: I3d9432849560df81536bbb2ce4c87cd265b820f7
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs that are being set low had the wrong value getting set.
FCH_GPIO_OUTPUT_VALUE was being set instead of FCH_GPIO_OUTPUT_ENABLE.
BUG=b:70234300
TEST=Build and boot Grunt
Change-Id: I16792b76252506a43aac92738b04096ae3fde01c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Grunt and Kahlee touchpads are on different i2c busses; I2CC and I2CD,
respectively.
Since grunt is the 'baseboard', put its configuration under baseboard, and
include it from the grunt variant.
BUG=b:71820409
TEST=Boot grunt to kernel, use evtest to test trackpad.
TEST=Boot kahlee to kernel, use evtest to test trackpad.
Change-Id: I1aeacf9a840342e73c1e219a825b39a124b4dd57
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23232
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Grunt and Kahlee have different audio codecs.
Create a new audio .asl for the baseboard for grunt's codec, link
to it from the grunt mainboard, and move the kahlee codec table
from the baseboard mainboard to its own .asl in variant/kahlee.
Note, we can't use the generic drivers due to the PCI scope
expectation. The AMD I2C are not PCI devices.
BUG=b:69397774
TEST=Codec driver loads. Check dmesg.
Change-Id: I1cc245357d1f3d444e5a5012466eaa5d75d637eb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23226
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the apci/ to the baseboard and move mainboard.asl to
each variant.
BUG=b:71873651
TEST=build
BRANCH=none
Change-Id: I8a829f2946e4b280cd78574eb8dbda6c2a9a1028
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Meowth uses GPD_2 as a dedicated lan_wake pin, so GPD_2 must
be set to use NF1 instead of gpio.
BUG=b:64395641
BRANCH=none
TEST=none
Change-Id: Iadf7158a792dfae0ea5e824d197a558524cdb5fd
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Intense PC uses FCBGA1023 socket, not rPGA989. Correct the socket
in the devicetree.
Change-Id: Ie657af2f51dfb7add90b19b26c0c37d312d59821
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Enable the UART via SMSC SIO1007 SuperIO, this allows you to see boot
boot messages from coreboot over the integrated RS-232 port (requires
use of included dongle).
Change-Id: I11a4c532ed73a0cf27d6e7bef6e04035c3942567
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The code is based on autoport and that for 8470p.
Tested:
- CPU i5-3437U
- Slotted DIMM 8GiB
- Soldered RAM 4GiB from Hynix (There may be more models here)
- Onboard USB2 interfaces (digitizer, wlan slot, wwan slot, camera)
- Mini pci-e on wlan slot
- On board SDHCI connected to pci-e
- USB3 ports
- USB3 hub on dock (connected to USB3 port 1)
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.13.13-1 within Debian GNU/Linux testing, loaded from
SeaBIOS, or Linux payload (Heads)
Not work:
- An "NFC" device connected to LPC
Not implemented yet:
- Detecting the model of Soldered RAM at runtime, and loading
the corresponding SPD datum (3 observed) from CBFS
Change-Id: Iba9c361591697e6a2b3b7b485f7f1649c2a83524
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/22972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fizz has external Lan on PCIE port.
The Lan device on PCH is not used.
BUG=b:70889517
Change-Id: I99894bedec14a44724ac7c22d0c894132a795b78
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds the EC_GOOGLE_CHROMEEC_SWITCHES option so that we
use the common switch.c file
Change-Id: I93a2ba63015db17989c89ce1b5897de6a93e201f
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/23131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds recovery cache.
TEST:glkrvp boots with this change and also FAFT test
firmware_CorruptRecoveryCache passes.
Change-Id: I9b32628d814693fb0591fc3750348d48cf9e26f1
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/23067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Digitizer power is not controlled by SoC. Also, since the digitizer
uses I2C-HID driver in Linux kernel, the device is put into sleep
anytime system is suspended. Thus, there is no need to control the
reset gpio using ACPI power resource.
TEST=Verified that digitizer device is properly detected on boot-up
and after suspend/resume.
Change-Id: Id11b8412d0ac48b2701d53b0a22ad3b747b544ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of duplicating code in each mainboard that supports HDA use
the common driver and provide the HDA verb table.
This was compile tested for both variants with "abuild -t intel/kblrvp"
Change-Id: Ie3bab7aabcfa040935062b7764853df8fb19b04d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Port initializer had been changed from PortDisabled to PortEnabled,
but engine inializer hadn't been updated from PcieUnusedEngine to
PciePortEngine. Update this so the port works.
Also change disabled port to PcieUnusedEngine.
BUG=b:71818026
TEST=PCIe device now shows up on D2F4
Change-Id: I11eb8c1fbad12fa9cf34d758a4ef3c22ef8ba4f7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23210
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If using type-C charger, then PsysPl2 may be lower than barrel jack
value of 90W, so need to override value to the max power of type-C
charger.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 60W with zinger, but 90W
when using proper barrel jack adapter on and i7.
Change-Id: If955b9af0e23f47719f001f1d73ec37113937cea
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The spd.bin file was not getting generated properly, so moved logic
to variant's makefile.
BUG=b:64395641
BRANCH=none
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully and spd.bin is found when booting.
Change-Id: I4642d6ddb5e65f721d1bde31ca0ca5b4438da554
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The .spd.hex text is added to the name by the build process. This
was causing a failure because we were trying to add the files:
'file.spd.hex.spd.hex' to the build.
Remove the additional .spd.hex text.
BUG=b:71535311
TEST=Build
Change-Id: I11df7a90c979503676a66c6502900a13f1a8e359
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure
that required SPD hex files are included in the SPD binary.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I449ab56dfc7a75752944b58ba6291b5ee32f81ad
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/22205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Since the current hardware revision does not have external pull on the
pen eject signal, this change adds internal pull-up on it.
Change-Id: I426d9833d7efbd8735b6f2b4896d1012b62cb4b8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tony Lin <tonycwlin@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Rainier, a scarlet derived board, was configured to use spi0 for tpm
driver by default. This patch switches it to spi2 to reflect recent
changes in scarlet-derived boards.
Change-Id: Ib67109786512c068bb957890f456bccff7addc86
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/23129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch allows temperature sensors 1 and 2 to function by setting
their type to be thermistor instead of BJT.
Change-Id: I6491171eacc0c9848ba86ba7a62ec440226aae36
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Reviewed-on: https://review.coreboot.org/22922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch adds the temperature sensor type device tree setting,
configured to be the default value as stated in the Fintek f71869ad
datasheet on page 60.
bit 7-4: reserved (0)
bit 3: T3_MODE 1 (default) = BJT, 0 = thermistor
bit 2: T2_MODE 1 (default) = BJT, 0 = thermistor
bit 1: T1_MODE 1 (default) = BJT, 0 = thermistor
bit 0: reserved (0)
This results in a default value of 0x0E
This change is needed to make sure behaviour does not change after
applying change 22935 which adds the temperature sensor type
devicetree configuration option
Change-Id: I42980988267621def6576f771f1d8a853500e867
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Reviewed-on: https://review.coreboot.org/22966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested on Linux 4.13.14:
SuperIO resources show up as reserved in /proc/ioports and friends.
Change-Id: I0363816fe048579413f1325dcfc9a6a8a9e48123
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Grunt's devicetree dropped some entries when it was split from the
kahlee variant. This commit restores:
spd_addr_lookup - memory information for AGESA
dram_clear_on_reset - keeps DRAM contents on reset
uma_mode - needed for vbios
uma_size - needed for vbios
Change-Id: I1d8cdc97594867f1d706318370055087976a5104
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Especially on ICH7 failing to do so results in i2c block read being
unusable. On ICH10 this problem doesn't manifest itself that much.
This moves disabling the watchdog reboot to the northbridge code like
i945 (even though it technically is southbridge stuff).
TESTED on Intel DG41WV: hacking on raminit is much nicer since no
need to do a hard power down for +4s are needed to clear the timeouts.
Change-Id: Icfd3789312704f61000a417f23a121d02d2e7fbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The spd size of DDR4 is 512, but the size empty.spd.hex is 256.
With empty.spd.hex and DDR4, it will cause mainboard_get_spd_data
loads spd data incorrectly due to the offset is wrong.
Change-Id: Iea3f216898525a2a602fabf1835c8a0c1245ee57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change is to enable SataPwrOptEnable.
With this change, we no longer see SError message in kernel during
suspend_stress_test.
BUG=b:70491485
Change-Id: Ieb991f6889c5ff3181a670bc7702314049fa983c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The cmos.layout files are copied from lenovo/x230 with EC options
removed.
It's tested on 8470p and the power_on_after_fail option works.
Change-Id: I0a50a25798fd31b7acccf9872c50dac2718ce895
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/22842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
In commit 7a95204 (intel/dcp847ske: Add Intel NUC DCP847SKE)
the default_irq_route.asl file was removed, but this mainboard
was missed. Follow suit with the original intent of the commit
and fix the build breakage.
Change-Id: I909dad7cfc0fab37e29187b2358f7f056216a403
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22975
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This speeds up the SPD read ('calling FspMemoryInit' phase) from
218ms to 134ms consistently.
Tested on both the Librem 13 v2 and Librem 15 v3.
Change-Id: I44fbe96c256972bd074537159771d61fe7adf082
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
https://ark.intel.com/products/71620/Intel-NUC-Board-DCP847SKE
Created using autoport and manual edits.
mainboard_fill_pei_data copied and adjusted from samsung/lumpy.
Tested:
- RAM slots with 2x4GB Kingston KVR1333D3S9/4G (DDR3-1333 1.5V).
- RAM slots with 2x4GB Kingston KVR16LS11/4G (DDR3L-1600 1.35V).
- SeaBIOS stable payload.
- Linux 4.13.14 payload.
- Booting into Linux 4.13.14 with Debian/unstable installed on the
internal mSATA slot.
- Non-native raminit (works).
- Native raminit
- KVR1333D3S9 doesn't work.
- KVR16LS11 only works at 1.5V.
- Native VGA init, HDMI port detection with libgfxinit.
- Basic ACPI functions (power button event; power-off; reboot).
- Suspend to RAM and resume works.
- PCIe WLAN in half-minicard slot.
- USB device in half-minicard slot.
- PCIe device in full-minicard slot.
- mSATA device in full-minicard slot.
- Fan spins up/down in response to CPU load.
Known issues:
- Native raminit fails timC calibration with the RAM I have.
- Technical Product Specification mentions overcurrent protection
for back panel and front panel USB connectors, but I haven't
been able to trigger it with either native fw or coreboot
(tried up to 2.5A load).
Untested:
- USB debug port.
Change-Id: I6e210310f55c051eaf61e0698fed855eda5d7d90
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch revises LED0 Green light behavior from patch 2ecf3f8c.
For 100Mb link speed, LED0 should be OFF.
BUG=b:65437780, b:68284778, b:69950854, b:65808944
BRANCH=None
TEST=Run DUT with 100Mb and 1000Mb ethernet connection and observe
LED0 is behaving as expected.
Change-Id: Ia805c955711b8ce77eba087a28427a005c456fa1
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22964
Reviewed-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
firmware test team is requesting that default gbb flags set to 0x39
rather than 0x239 so that it's consistent with the default gbb flags
of other platforms.
BUG=b:70392534
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage
gbb_utility --get --flags image-fizz.bin and make sure
that it returns 0x39 instead of 0x239
Change-Id: Ib73e4619b13f6b7c2d01598c926fbbd7d7eb9bef
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22962
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
apu4 is new version of PC Engines platform, which contains 4 Ethernet
ports and 4GB of RAM. In functional way it is very similar to apu3.
Platform tested with booting Linux voyage (kernel 3.16.7) using USB and
SeaBIOS as 1st stage and GRUB as 2nd stage bootloader. Also Debian
(kernel 4.8.5) using iPXE.
Change-Id: Ia7a9971d25d4ecc215c392be1e46dc1c10129ba7
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/22629
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In commit 7f5efd90e (intel/bd82x6x: Use generated ACPI PIRQ)
the default_irq_route.asl file was removed, but this mainboard
was missed. Follow suit with the original intent of the commit
and fix the build breakage.
Change-Id: Iac233b802239e4e5cfc66d9545bb637ec4f9f541
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22958
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch configures the EC_SCI_GPI when ESPI is enabled.Also adds
mainboard espi handler function.
TEST= Boot to OS and SMI/SCI is working when ESPI is enabled/disabled.
Change-Id: I2b3845d54ad7c1f14edc86f71b3f968424711999
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
coreboot console output during POST shows that the EC
replay fails to communicate with the EC. Since the replay
has no effect, it should be removed from the boot process.
coreboot log:
Replaying EC dump
.......Timeout while sending command 0x81 to EC!
.......Timeout while sending data 0x00 to EC!
(snip)
.......Timeout while sending command 0x81 to EC!
.......Timeout while sending data 0xff to EC!
.......Timeout while sending data 0xff to EC!
done
Change-Id: I05fb6358b40f442337f5768afa6253cd9bc32ee1
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There is a potential IMVP8 issue for KBL that affects Intersil VRs
Fizz is using one of the affected parts. The fix is to use an updated
microcode and also send a mailbox box command from FSP.
BUG=b:65499724
BRANCH=None
TEST=Build and boot Fizz
Change-Id: Iebfda02df88ea0d2aaf79e8449b95c0eb2165c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Intel version of ThinkPad X131e can ship with Sandy Bridge or
Ivy Bridge processors. The mainboard uses 8MiB+4MiB flash chips, with
the 8MiB chip containing the IFD and ME, and the 4MiB chip containing
the BIOS. The flash chips can be accessed with an external programmer.
This port was primarily created using autoport, with some parts adapted
from lenovo/x230 and google/stout.
Tested and working:
- Machine type 3367AH5 / Intel Celeron 887 (Sandy Bridge)
- Boots Debian GNU/Linux 9.2 (Linux 4.9.51) via SeaBIOS
- Boot from internal SATA and USB
- Native RAM init
- Native VGA init
- libgfxinit
- VGA and HDMI display output
- Keyboard, trackpoint, touchpad
- Audio (speaker, headphones)
- Ethernet (Realtek)
- Display backlight
- USB 3.0 ports
- "Always on" USB port (EHCI debug)
- SD card reader
- Webcam
- Fan and temperature sensors
- ACPI S3 (Sleep)
- CMOS
- TPM
Not tested:
- WLAN/Bluetooth (Broadcom)
- WWAN/mSATA (no card)
- Other operating systems
Not working or not implemented:
- Fn keys
- ACPI S4 (Hibernation) "Image mismatch: memory size"
Change-Id: If8de3a9308997e2d57aee869023ee9a43a2db872
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/20694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The current fan level should be zero at boot and only be modified by
ACPI or SMI code.
Change-Id: I72b59f05746b28cfb24c4f018aebc2befa9caba6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
SATA was enabled only for internal testing. Since we do not use
SATA on chrome platforms, it can be disabled.
Change-Id: I907b440562b39e6d97f604e7e63b6b99e487aaa8
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/22875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It seems that RAM code 0 has been strapped with an incorrect resistor on
Kevin. The resulting voltage divide still puts it well within the ADC
value bucket reserved for that slot, but a little closer to the edge
than necessary. While this doesn't seem to cause any immediate problems
on its own, it still doesn't hurt to fix it (if only for the
documentation value).
On other boards (at least on my Scarlet) the strapping seems to be
correct.
Change-Id: Ic5199834fbeaf734e725ff45b04f45eefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22891
Reviewed-by: David Schneider <dnschneid@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch shifts some comments around to make it easier to replace
values in the ADC strapping bucket table with compile-time conditionals.
Change-Id: Ic51917d3961a51d4e725ff824fb59aeefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
ACPI bit is not set after an S3 resume, so set it in _WAK. Setting
SLPT bit can make the power LED blink in S3.
Change-Id: I2badc69510275df57938cb8607b3c4e0df50f028
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/22929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This platform shares most hardware components with first-gen Core
Lenovo laptops such as T60/X60, with much smaller EEPROM size as
one of notable differences. The port features Intel graphics,
ATI-based version should work with vendor VBIOS.
Tested peripherals:
- sleep/resume,
- USB ports,
- ACPI Fn key bindings/volume buttons,
- backlight control,
- ethernet,
- wireless (under Linux),
- sound/beep,
- dock handling,
- serial via dock.
Untested peripherals:
- IrDA,
- parallel port,
- PCMCIA,
- S-Video port,
- modem,
- FP reader (should just work),
- IEEE1394.
Linux 3.16 works with native gfxinit perfectly, with Intel VBIOS
console sometimes displays nothing when i915 framebuffer is used.
Windows 7 has an interrupt assignment issue with iw3945, otherwise
tested stuff is fine.
Change-Id: I84c89cc47d3db126d827f92d50270954bc42f224
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
Reviewed-on: https://review.coreboot.org/21019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add initial files to support the Saddle Brook board. This board uses the
Skylake FSP 1.1 image and does not build without the FspUpdVpd.h file.
Most of the code has been taken carried over from kunimitsu with changes
done for Saddle Brook.
Saddle Brook is a reference board for Skylake SOC and has DDR4.
TEST=Build with uefi payload and boot to Linux 4.9 on CRB successfully.
Change-Id: Ie221eb58e8ab8ff15e9ef19c1d145a5eb2921b4e
Signed-off-by: Anuj Mittal <anujx.mittal@intel.com>
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/21436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
As per the latest schematics, this change configures GPP_B0 for WLAN
wake and uses corresponding gpe bit in ACPI node for WLAN. This hasn't
been tested yet.
BUG=b:70775494
Change-Id: I5198b8083a87d00f890b45986e5e3f62b81686c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22928
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Similar to other KBL projects, this change enables AER and LTR for
root port 1 on poppy.
BUG=b:65570878
Change-Id: Iadad3d2fc46cbba575a776071305925c529a6760
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change really fixes the SataMode to select non-RAID mode and
enables SATA which was incorrectly disabled in a71276b
(mb/google/poppy/variants/nami: Fix SataMode configuration in
devicetree).
BUG=b:70160119
Change-Id: Ied6adabdc1d2458972bde628616a198cd41f9f3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Nami uses DEVSLP1 and not DEVSLP0. This change updates the GPIO
configuration for DEVSLP to match the latest version of schematics.
BUG=b:70160119
Change-Id: Ifa181322011a4b8947ecd0fa44dcf790b0d8f657
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch enables customized NIC leds as below:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:69950854
TEST=Boot on fizz dut and observe the LEDs are behaving as expected.
Perform suspend/resume test and the LEDs are still working as expected.
Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
