With chipset_power_state filled in romstage CBMEM hooks and
GNVS allocated early in ramstage, GNVS wake source is now
also filled for normal boot path.
Change-Id: I2d44770392d14d2d6e22cc98df9d1751c8717ff3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Additionally to the PCI IDs of Cezanne it also handles the Renoir ones.
The main difference between those two is that Renoir has two core
complexes while Cezanne only has one core complex. I haven't seen
incompatible changes between those two though, so for example the fabric
IDs are the same and the one that's only present in Renoir is just not
used in Cezanne. Also adding the ACPI parts for those don't have
anything to do with those differences.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3b2517bc15d872f41183a33857333f1972ff2cb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Move `CROS_GPIO_DEVICE_NAME` to a new `chromeos.h` header, because
Lynxpoint uses a different value. Also drop unnecessary includes.
Tested with BUILD_TIMELESS=1, Google Tidus remains identical.
Change-Id: I38baed2c114fb93cfb82535a6ec00fb67e596d64
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50080
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use `lp_gpio.h` from Lynxpoint instead. Subsequent commits will update
the mainboards and then drop all GPIO code from Broadwell.
Tested with BUILD_TIMELESS=1, Google Tidus remains identical.
Change-Id: Idef89037c2ca781ac3e921abb4b3dc3f7c4b3b5f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50079
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move prmrr_core_configure before clearing MCEs.
This is required for the following patch in order to update microcode
after PRMRR has been configured, but before MCEs have been cleared.
According to Document 565432 this should be no issue in regards to
SGX activation.
Change-Id: Id2808a3989adff493aaf4175cbeccd080efaaedf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This function is more convenient to get the value of a single bus number
than get_cpubusnos(). Now get_cpubusnos is not used anywhere, so remove
it.
Change-Id: I71c06c2d69344d97e48609e67a3966ed8c671152
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When USE_PSPSECUREOS isn't selected, we get stuck in FSP-S.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I60d0e5ab0bd9f4d76cc48d08ca05d27c60e898c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
I'm not 100% sure yet if this code will be common for all AMD SoCs, so
I'll add a copy for Cezanne for now. This part of the code should
probably be reworked after the initial bringup of Cezanne anyway.
DF MMIO register configuration at the beginning of
data_fabric_set_mmio_np:
=== Data Fabric MMIO configuration registers ===
Addresses are shifted to the right by 16 bits.
idx control base limit
0 a3 fc00 febf
1 a3 1000000 fffcffff
2 a3 d000 f7ff
3 a0 0 0
4 a3 fed0 fed0
5 a0 0 0
6 a0 0 0
7 a0 0 0
DF MMIO register configuration at the end of data_fabric_set_mmio_np:
=== Data Fabric MMIO configuration registers ===
Addresses are shifted to the right by 16 bits.
idx control base limit
0 a3 fc00 febf
1 a3 1000000 fffcffff
2 a3 d000 f7ff
3 10a3 fed0 fedf
4 a0 0 0
5 a0 0 0
6 a0 0 0
7 a0 0 0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia243a0cad311eb210d14d6242c52f599db22515c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50624
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The number of data fabric MMIO registers is SoC-specific, so we need to
keep that in the SoC code. This also removes a redundant pair of
brackets and moves a loop counter declaration into the head of the loop.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8499f1c1f7bf6849b5955a463de2e06962d5de68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50638
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The exact same mechanism is used on Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3179d8ec35efa29f9bc66854c3690b389d980bba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50619
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix regression with commit aa969e887a ACPI: Move PICM declaration.
While mentioned in the commit message there already, the default
value for AMD boards changed from IOAPIC mode to PIC mode.
ACPI 6.3 spec has this text regarding _PIC method:
If the platform CPU architecture supports PIC mode and the method
is never called, the platform runtime firmware must assume PIC mode.
If MADT has IOAPIC entries, OS will want to change to APIC model. But
the method _PIC was not in the global scope so it could not be called
and therefore _PRT continued to report PIC model interrupt routing.
Already fixed for soc/amd/picasso in commit 839f668.
Change-Id: I7f3bb0d45946cec315694de1d540fea4d828348e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This will be common for all boards, so move it to the chipset device
tree.
TEST=CPU cluster and LAPIC still show up in console logs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia49e7b4cfc09c60b6152b8ccc47f37b6adc1e319
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50613
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MADT doesn't populate the IO-APICs yet since we need FSP to
configure those.
The FADT differs from picasso in the following ways:
* The duty_offset is supposed to be 0
* Don't clear x_firmware_ctl_l
* Make the extended addresses use MMIO
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib6c3a01084a0de33894885b47c637a292d252ed4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
TEST=Boot majolica and see microcode update
CBFS: Found 'cpu_microcode_blob.bin' @0x6900 size 0x15c0 in mcache @0xcf7fe9d8
microcode: patch id to apply = 0x0a50000b
microcode: being updated to patch id = 0x0a50000b succeeded
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If50b1d8b3ebf4b3e6f8a9dd3ab96073e0cb92424
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We also want to support uCode loading on cezanne.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6f10564c93ce72aea7ff52a8565d65d8b56452f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Stoneyridge used CONFIG_MAX_CPUS and CONFIG_MAX_CPUS + 1 directly as
IOAPIC IDs and Picasso had Kconfig options to configure that, but still
used the common SMBus controller code that used CONFIG_MAX_CPUS as ID
for the FCH IOAPIC. If a board overrides the PICASSO_FCH_IOAPIC_ID
Kconfig option to a value that isn't CONFIG_MAX_CPUS, we'll get a
mismatch between the ID that gets written into the FCH IOAPIC register
and the ID in the corresponding ACPI table. In order to avoid that add
defines to each SOC's southbridge.c and use them in all soc/amd code.
Change-Id: I94f54d3e6d284391ae6ecad00a76de18dcdd4669
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50575
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When USE_PSPSECUREOS isn't selected, we don't even get post codes on
Majolica, so remove this option.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0ec976f40d962a2d9f2bd36dc97d86526bd661ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Without this part being present in amdfw the PSP won't enter its normal
operation mode, but goes into recovery mode instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If13b5495e9f246afd0317daaa53c3d2cefbaa4dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
On Picasso we missed setting this bit in coreboot and since the default
after reset is 0, we had to rely on the FSP to set this bit. Stoneyridge
and Cezanne have the HPET decode enable bit in the same position in the
same register. In the ACPI table entry written by
southbridge_write_acpi_tables the HPET entry gets added, so we should
make sure that we enable the decode.
TEST=HPET still works on Mandolin.
Change-Id: Ie98dae1d6036748f700f884d4b9653f2e59c24da
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50512
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The default value of this bit is 0, so set it right before calling
setup_ioapic to make sure that it's set and not to have to rely on FSP
doing the right thing.
Change-Id: Ife886451a6927965769282fc5644c2085abb9585
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50513
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A copy of Picasso's include/nvs.h was added to Cezanne right before the
commit d6ccbb9d48 that removed it for the
other mainboards and SoCs, so apply the equivalent change here as well
to keep everything in sync.
Change-Id: I76b551c05b3c3028a3afb3bc3b77df2401aed7a8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This is another common ACPI setting.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iefecabae1d83996a9a4aaadd2a53c2432441e1b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50558
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is ACPI specific config that applies to all the AMD SoCs. Stoney
doesn't currently use this, but we can add that functionality later.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0be7d917d7c5ba71347aa646822a883e2cf55743
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50557
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is common between stoney, picasso, and cezanne.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5fb40e8c6817773212c5fbd66c5c06bd2bae1eda
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50556
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is common between all the chipsets.
It's also required by common/block/lpc/lpc.c.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I361dfabfe0c04667a2c112955133831a985d5cc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
These definitions were identical to picasso. The only thing I changed
was that I renamed Misc1 and Misc2 to HPET_L and HPET_H.
This change still doesn't write the PCI_IRQ register for all the PCI
devices. We need to refactor the picasso pci_gpp code first.
TEST=Boot majolica and see FCH IRQs being programmed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic7e637f234d3af426959a9bbd82a0dcf25bb3c8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50451
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=Majolica still gets to SeaBIOS. Like before this patch the PSP
still has the recovery flag set in its return value, but we likely still
have some problem in the amdfw part or miss some PSP initialization in
FSP.
Change-Id: I9f343452ef2ea6b01f9b2fd0cf6371218d046046
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The RTC functionality will be used by elog.
Change-Id: I3a8d0a353620f64207d5ba8e17c145090f0c7506
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The same functionality will eventually be needed on Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib49124c2c774ad3352ea2f7d8d827388029be041
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Since SMM is in TSEG on the platforms which is the default, drop the
SMM_TSEG condition for the default of SMM_TSEG_SIZE.
Change-Id: I7bd965c0794efa12ea4886a55522cc5193a1d3ac
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50498
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The corresponding bit is marked as reserved in the PPR. Also there's no
BKDG for Picasso any more; the BKDG was mostly replaced by the PPR. Also
fix the style of the comment.
Change-Id: Iffdbb9e951cb140e4352ab0f198f72a71ba798dc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50495
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variable PICM was not inside GNVS region and can use a static
initialisation value.
For most AMD platforms PICM default changes from 1 to 0.
Fix comments about PICM==0 used to indicate use of i8259 PIC for
interrupt delivery.
Change-Id: I525ef8353514ec32941c4d0c37cab38aa320cb20
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49905
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The value should be set by OSPM using some combination of
_OSI() queris in the \_SB._INI() method.
To maintain previous behaviour with this commit, boards where
GNVS osys initialisation was removed now do the same in ASL.
Change-Id: Id4957b12a72fbf7fa988e7ff039e47abcc072e1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49353
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initialize variable to 1 to indicate AC power supply.
If platform has EC it will set this correctly based on
whether plugged on the charger or not.
Change-Id: I3f834cf7563b9e512fcab34cdb7a27a9f0fd31c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49352
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only the ACPI enable/disable functionality is implemented and sleep is
also not implemented yet. This will be added in future patches.
Change-Id: I7701944023ce2e86586679c32c4138d4488768a1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50488
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This doesn't select HAVE_ACPI_TABLES, so no ACPI tables will be
generated for now. There's also no globalnvs.asl that corresponds to
nvs.h yet. The added nvs.h has some currently unused fields, but still
having them in the struct aligns it with Picasso and also might reduce
the noise in future ACPI patches a bit. When most of the ACPI code for
Cezanne has landed, we need to do a cleanup though.
Change-Id: I3d658d284fa67e4da43a89d74686445fd5e93b1f
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
signed int should only be used when we need negative values and in those
cases the value shouldn't became negative.
Change-Id: Iefac021260ff363c76bf5cd3fe3619ea1dbabdba
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50486
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MCA MSRs aren't getting cleared and no microcode update gets applied
for now. Both will be added later.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I38ce5d11787ffefdd0183c5540ae2683158cbee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50482
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SerialIO is in ACPI mode for google/auron and intel/wtm2, and is
disabled for google/jecht and purism/librem_bdw. Since Broadwell
SerialIO is never used in PCI mode, _ADR can safely be dropped.
Change-Id: I9a99b8209b5c139146012aa4a92f563692b62c5e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The common code gets moved to soc/amd/common/block/cpu/smm, since it is
related to the CPU cores and soc/amd/common/block/smi is about the SMI/
SCI functionality in the FCH part. Also relocation_handler gets renamed
to smm_relocation_handler to keep it clear what it does, since it got
moved to another compilation unit.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I45224131dfd52247018c5ca19cb37c44062b03eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50462
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The old name was misleading, since it doesn't disable the generation of
SMIs, but clears the status registers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iddadbec013091c2e5993a6303e291451c3d1e7ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50459
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This also aligns Stoneyridge with Picasso and Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I35bf9915e3502c22e9dd9efa80b00a1ce70f187d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50436
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setup the config required to support verstage.
The offsets are the same as picasso.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I82874d649db3c9c370e32841e6a9898efb70082e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Required so we pass SPI information down to depthcharge.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4ce819b537333c28d394c925331e3dbf260b7732
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The picasso SPI registers are different than the ones defined in
amdblocks/lpc.h. The BASE_ALIGNMENT has changed and the
PSP_SPI_MMIO_SEL bit has been added.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0b5a0c88c6dbb95cdbc62b949a7d30bfad1fa725
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This is a copy/paste of amdblocks/lpc.h. The registers are different for
picasso and cezanne, so I'm moving them to soc.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4dfadcdc025d3581cb1423e9793a9b2181742b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
PEP table is applicable to Skylake platform as well. It is required to
make the kernel load `intel_pmc_core`. Skylake boards can also use S0ix
hooks.
Tested on an out-of-tree Acer Aspire VN7-572G (Skylake-U),
intel_pmc_core kernel module is loaded and reports statuses predictably
via debugfs.
Change-Id: I08d8c1fde4f447e9292a0508649f802fdc2721e1
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49140
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The transfer buffer is only required when using
VBOOT_STARTS_BEFORE_BOOTBLOCK.
The VBOOT workbuffer is only required when VBOOT_STARTS_BEFORE_BOOTBLOCK
or VBOOT_STARTS_IN_BOOTBLOCK.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I444bede3f2b716e1900e7621453351d7fddadaa3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
southbridge.c was renamed and split into early_fch.c and fch.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie439e746fb3dfe9ec865481a76a09eab378242bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50458
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the PSP didn't like a command this should be at least a warning on
the console and not just a debug message.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If7e5f6320631cca86813e98f82b8c0c21bf18af1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reduces the differences between Lynx Point and Broadwell.
Change-Id: Ib53d73e3f89c538ba0f052a98c7aabe815a59472
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46891
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SCI IRQ is always set to IRQ 9 in the bootblock. To allow using
common MADT code on Broadwell, hardcode it as 9 everywhere.
Change-Id: I84345b7985b1996369cecc4bcb0a3668d002a922
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change uses the following information to determine the
appropriate S0ix states to enable as per PDG document: 607872
for TGL UP3 UP Rev2p2 (section 10.13):
1. SoC - UP3 v/s UP4
2. H/W design - external phy gating, external clk gating, external bypass
3. Devices enabled at runtime - CNVi, ISH
In some cases, it is recommended to use a shallower state for
S0ix even if the higher state can be achieved (e.g. with external
gating not enabled). This recommendation is because the shallower
state is determined to provide better power savings as per the
above document. Deepest state expected on tigerlake up3 based
platforms is S0i3.2.
BUG=b:177821896
TEST=Build coreboot for volteer. Verify that deepest
S0ix substate that is enabled is S0i3.1
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Change-Id: I5f2ac8b72d0c9b05bc02c092188d0c742cc83af9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49766
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Triggering SMI is not part of the semantics of global_smi_enable(), so
move it to the post_mp_init handler. Even without the !acpi_is_wakeup_s3
check we don't get PSP warnings/errors during resume, so we can drop the
workaround introduced in commit 5dbe45e0f5
in this patch.
Change-Id: Id0e7723c2bb9811f80fe36c38199a01445dc1d7d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42987
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 75f6ab35ff.
Reason for revert: The 5.4 Linux kernel is not configured for AMDI0030. This causes an issue where the WP pin is not recognized.
BUG=b:179320024
TEST=WP pin shows up properly in crossystem after reverting this change.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I0850fd085b5ee70522752633900f69d4d3732321
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50052
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a copy/paste of picasso with a few things removed. With this
change we can jump into depthcharge.
Allocated resources:
PCI: 00:00.0 resource base 0 size a0000 align 0 gran 0 limit 0 flags e0004200 index 0
PCI: 00:00.0 resource base a0000 size 20000 align 0 gran 0 limit 0 flags f0000200 index 1
PCI: 00:00.0 resource base c0000 size 40000 align 0 gran 0 limit 0 flags f0004200 index 2
PCI: 00:00.0 resource base 100000 size 1f00000 align 0 gran 0 limit 0 flags e0004200 index 3
PCI: 00:00.0 resource base 2000000 size 1c0000 align 0 gran 0 limit 0 flags f0004200 index 4
PCI: 00:00.0 resource base 21c0000 size cde40000 align 0 gran 0 limit 0 flags e0004200 index 5
PCI: 00:00.0 resource base f8000000 size 4000000 align 0 gran 0 limit 0 flags f0000200 index c0010058
PCI: 00:00.0 resource base 100000000 size 30e340000 align 0 gran 0 limit 0 flags e0004200 index 6
PCI: 00:00.0 resource base 40e340000 size cc0000 align 0 gran 0 limit 0 flags f0004200 index 7
PCI: 00:00.0 resource base 40f000000 size 1000000 align 0 gran 0 limit 0 flags f0004200 index 8
PCI: 00:00.0 resource base 410000000 size 20000000 align 0 gran 0 limit 0 flags f0004200 index 9
PCI: 00:00.0 resource base cfffe000 size 2000 align 0 gran 0 limit 0 flags f0004200 index a
PCI: 00:00.0 resource base ceffe000 size 1000000 align 0 gran 0 limit 0 flags f0004200 index b
TEST=Boot majolica and see depthcharge finally loading:
Starting depthcharge on MAJOLICA...
new_rt5682_codec: chip = 0x1A
Looking for NVMe Controller 0x3004cac8 @ 00:01:07
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I52682ec2a06c7e219c221648f241e18e26a9358e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50339
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The same functionality is needed on Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I40f9d2fe7d144e94369a417225bcca0a299d1f45
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
No PCI or PNP functions are used in here.
TEST=Timeless build results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I577e2ecdc59dbd09e739ae800cbe021168a34812
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50399
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No PCI or PNP functions are used in here.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46851656db1f1866a82f06ceab67c93019cc6af1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
ACPI S3 is a global state and it is no longer needed to
pass it as a parameter.
Change-Id: Id0639a47ea65c210b9a79e6ca89cee819e7769b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Hide the detail of allocation from cbmem from the FSP.
Loading of a BMP logo file from CBFS is not tied to FSP
version and we do not need two copies of the code, move
it under lib/.
Change-Id: I909f2771af534993cf8ba99ff0acd0bbd2c78f04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We can never pass memory location of dynamically loaded BMP files in the
static devicetree. The parameters passed to FSP are filled at runtime.
Change-Id: Ib835ec0d9349ec96d5635e228063f2b7000b70fd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The only reference to CID1 is in common/acpi/wifi.asl and
only two braswell boards include it. Everywhere else
the value in GNVS was unused.
Change-Id: I09ea756fb3743e33d1e221f0a0df3a6fdc3fc3ba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix compilation on GCC 10.2.1 and address the underlying issue. The
printf format specifier for a size_t type is z.
Change-Id: Ieb1db6c0c3eb4947bd3617e418bac238b70ec08f
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Alderlake includes latest VBT (version 237 onwards),which has size of
8.5 KiB. This change is specific to alderlake so utilizing Kconfig option
to increase VBT size specifically for ADL platforms.
BUG=None
BRANCH=None
TEST=Include new VBT and boot the platform. Able to see firmware screen
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Change-Id: I438f4bce0a2dfa208e1cd59d1cd5dd1c5ad50833
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
No board in tree selects a different base address, so this can be
removed from Kconfig and be treated like the other base addresses in the
I/O space that are defines in iomap.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iec3d4476e3a6a5d2b226edef4c41f503a0c81f33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since I'm not sure if there are non-upstream boards that change the
default of the Kconfig value and the comment says that it needs to match
the binaryPI build, I'll do that change in a follow-up patch to allow
easy local reverts of that.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic0f08c6cb951994be6db19e10f73f0c621521c70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Needed so we can reserve the memory.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8f5bb9d97932f75ca4ce22fbe9df4c0148acbea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We need the same functionality for cezanne.
TEST=Boot ezknil
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0800c662bb473eb571c74e76a8247298f534b53f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add support for MP services2 PPIs, which is slight modification
over MP services 1 PPIs. A new API StartupAllCPUs have been added
to allow running a task on BSP and all APs. Also the EFI_PEI_SERVICES
parameter has been removed from all MP PPI APIs.
This implementation also selects the respective MP services PPI version
supported for SoCs
BUG=b:169196864
Change-Id: Id74baf17fb90147d229c78be90268fdc3ec1badc
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change drops the config FSP_PEIM_TO_PEIM_INTERFACE.
FSP_PEIM_TO_PEIM_INTERFACE is used for:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
* Adding ppi to subdirs-y
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
and is selected by SoCs that want to enable MP PPI services.
Instead of using the indirect path of selecting MP PPI services, this
change allows SoC to select FSP_USES_MP_SERVICES_PPI directly. The
above uses are handled as follows:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
--> This is handled by SoC selection of FSP_USES_MP_SERVICES_PPI.
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
--> The guard isn't really required. The Kconfig options in this
file don't present user prompts and don't really need to be guarded.
* Adding ppi to subdirs-y
--> Makefile under ppi/ already has conditional inclusion of files
and does not require a top-level conditional.
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
--> This is set to y if FSP_USES_MP_SERVICES_PPI is selected by SoC.
TEST=Verified that timeless build for brya, volteer, icelake_rvp,
elkhartlake_crb and waddledee shows no change in generated coreboot.rom
Change-Id: I0664f09d85f5be372d19925d47034c76aeeef2ae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50274
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It was commented that the need for the delay was mainly related
to external displays and only with VBIOS execution. Move the
delay such that it is done only when we actually need to execute
the VBIOS aka option rom.
A delay is currently only defined for librem/purism_bdw in
its Kconfig. As the description of the issue sounds like it
would equally happen on other platforms when VBIOS is involved,
promote the Kconfig visible option to global scope.
Change-Id: I4503158576f35057373f003586bbf76af4d59b3d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For the moment, these are most not used but become a necessity
for a unified <soc/nvs.h> approach.
They would be required for the implementation of _SWS method
for OSPM to determine the reason for system waking up. The related
hardware registers are present with these platforms.
It's expected that ACPI power-management related GNVS entries are
grouped together to form a single struct in later works.
Change-Id: I6d31d39ac1017cd6fdf0ac66b418d1fbb1edf8e0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50193
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add UPD for RV2 USB3 phy setting adjust.
Note: it only for RV2 silicon and not available for RV/PCO.
Usb 3.1 PHY Parameters:
1. RX_EQ_DELTA_IQ_OVRD_VAL
-Override value for rx_eq_delta_iq. Range 0-0xF
2. RX_EQ_DELTA_IQ_OVRD_EN
-Enable override value for rx_eq_delta_iq. Range 0-0x1
3. Override value for rx_vref_ctrl. Range 0 - 0x1F
4. Enable override value for rx_vref_ctrl. Range 0 - 0x1
5. Override value for tx_vboost_lvl: 0 - 0x7.
6. Enable override value for tx_vboost_lvl. Range: 0 - 0x1
7. Override value for rx_vref_ctrl. Range 0 - 0x1F
8. Enable override value for rx_vref_ctrl. Range 0 - 0x1
9. Override value for tx_vboost_lvl: 0 - 0x7.
10. Enable override value for tx_vboost_lvl. Range: 0 - 0x1
BUG=b:175192931
TEST=Build/verify the valule will been apply on dirinboz
Change-Id: I1d5f69e840952cc5171af1ce8597628d1bede5cb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50240
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The offsets of ACPI_CPU_CONTROL and ACPI_GPE0_BLK match the ones from
the reference code, but not the PPR. I've submitted a change request for
the PPR, so this mismatch might go away in the future. The case for
HAVE_SMI_HANDLER will be implemented in a future patch. If that one ends
up being identical to the function in soc/amd/picasso, I'll move it to
the common AMD SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If80b841df12d351d5a0c1e0d2e7bf1e31b03447f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This was the only I/O base address in Kconfig, no board changed it and
if a board changed it, it needs to make sure that it won't overlap with
other I/O resources, so just use the same value as constant in the
define instead of the value from Kconfig. Also remove the PICASSO_
prefix from ACPI_IO_BASE.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7ea62f1101ddefa8785da92de5ba2aaf7945694a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Make it clearer all the GPIO bank register programming
parameters originate from the same soc_amd_gpio entry.
Change-Id: I7aa6bd6996fd14dde4b1abcccbd2ae6ef933c87b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42691
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do this to reduce indentation a bit. Also it may be desireable
to group GPIO configuration such that some GPIOs are handled
outside program_gpios() call and would not be included in
gpio_list array.
Change-Id: I46cbe33f4d85cd9c7d70f96df82ee9b8ffe50a00
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42807
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For MT8192 MCUs, replace LZMA compression with LZ4 to speed up boot
process. The loading (plus decompression) time of mcupm.bin and sspm.bin
is consistently reduced by 8ms, respectively.
BUG=b:177389446
TEST=emerge-asurada coreboot
TEST=Hayato booted up
BRANCH=none
Change-Id: Ida35e7f6e0572ad43082e53bcc69bc708cf7da44
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Override SMBIOS type 4 max speed. This field should be maximum speed
supported by the system. 3900MHz is expected for Cooper Lake.
Tested=Execute "dmidecode -t 4" to check max speed is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I67edf657a2fe66b38e08056d558e1b360c4b8adc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Refactor PCIE port config structure. Make it easier to map from
schematic. We don't have to convert the PCIE ports RP number and
CLK source in devicetree. All the convert will be done by SoC level.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0b390e43f8e99b19cfad178139b86a2f77d7a57b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This is what Lynxpoint does. It is equivalent, but simpler.
Change-Id: Ifdbb291a6cea0bb29b4e46c7a33c5abe61dbe86b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47045
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new Kconfig symbols to mark FSP binary as x86_32.
Fix the FSP headers and replace void pointers by fixed sized integers
depending on the used mode to compile the FSP.
This issue has been reported here:
https://github.com/intel/FSP/issues/59
This is necessary to run on x86_64, as pointers have different size.
Add preprocessor error to warn that x86_64 FSP isn't supported by the
current code.
Tested on Intel Skylake. FSP-M no longer returns the error "Invalid
Parameter".
Change-Id: I6015005c4ee3fc2f361985cf8cff896bcefd04fb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Crash Data are collected and sent to the OS via the ACPI BERT.
BUG=None
TEST=Built, and BERT successfully generated in the crashLog flow.
Signed-off-by: Francois Toguo <francois.toguo.fotso@intel.com>
Change-Id: I00e390d735d61beac2e89a726e39119d9b06b3df
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The `_MASK` macros should be using the corresponding `_SHIFT` macros.
Change-Id: I78370e17d2396f77ab820771f93cf15957bcf674
Found-by: Coverity CID 1445928
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
A minimum of 100ms delay is required before sending a configuration
request to the downstream components. Since the kernel already adds
100ms, this change drops the extra 100ms delay in TBT PCIe root ports
_PS0 method in order to improve resume time.
BUG=b:177519081
TEST=Boot to kernel and validated various tests on Voxel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ic392f9af6cd739507a80a4ca3fd126088b513304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Picasso has 32 configurable GPEs, not only 28.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia156e64e7a69764776f3af7597b680b8ddd4e650
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In the case of passing 32 as limit the code returned -1, but should have
continued, since 32 is a valid value here.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6ca341841bad62abcb4ea26a350c539813a29de7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
According to Tigerlake TDP specifications (doc #575683, table 4-2),
TGL supports different TDP levels depends on CPU segement/package,
IA Cores and graphics configuration. For example, UP3 4-Core GT2
suppots base TDP=28W, Configurable TDP-Down_1=15W and Configurable
TDP-Down_2=12W. This configurable value can be used to select
suitable TDP level
Change-Id: I4242575807caac172b6cbe667839bf6c9241f3c5
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
There's no dedicated south bridge any more and now we have integrated
FCHs in the SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I19126da09f034f51b134f8d6ae2006f57fac1b0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50209
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART2 and UART3 don't exist on Cezanne which now has been verified, so
remove the corresponding AOAC offsets.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I67755bd34df3a835cc39929bdc24f711d158b3a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Because ACM already does TPM initialization.
Change-Id: I49cc3b0077b220b0ca0bfa048be1e3d3d7023b05
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
commit 3f2467032e changed this in the APCI
code itself, but the change in the ACPI byte code generation in
pcie_gpp.c was missed and this patch fixes that.
TEST=Fixes the regression on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I60de29581296101947336f70343d6206af97e307
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This define was copied over from Stoneyridge, but isn't present on
Picasso and newer.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ideb144c4bff441cf043a647b3f44a65691038eba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
It's a static value that is neither referenced from SMI handler
nor needs to be updated on S3 resume path.
Change-Id: Ife6611a11e5627d39d59e0e93af9aa2d87885601
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50121
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Baytrail had (only) occurence of DwordMemory vs DWordMemory.
Braswell one had bogus comments about the PCI memory range.
The actual region details are dynamically filled in _CRS.
Change-Id: I8d1bf45c6e5520c0b7643602843c665bfb81f9da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
