Since the h1 i2c bus is required for verstage mark the bus
as needing to be initialized early. That way, the bus is initialized
in bootblock prior to verstage.
BUG=b:70232394,b:69250772
Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Innolux didn't deliver a working init sequence yet for devices without
OTP programming. The sequence in this change has been derived from a
register dump of a mostly working panel with OTP. It is not meant to
be final, but to make devices with unprogrammed OTP work, while Innolux
is figuring out a proper sequence. There is a known issue with an
artifact line in the lower third of the display.
Change-Id: I7096506208e4cb29c5f31a7ac502231a6c23ac92
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some panels need to transfer initial code, and some of them will be
over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi
dsi transfer function to support it.
Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Set PsysPl2 values to 90% of max adapter power for all types of
adapters (typeC and barrel jack) to account for a 10% power loss from
the adapter to the soc.
BUG=b:71594855
BRANCH=None
TEST=reboot device and make sure Pl2 and PsysPl2 MSRs are properly set
with iotools rdmsr command on both U42 and U22 skus with both
typeC and barrel jack power adapters.
Change-Id: I8425c6d4d669449eccb9324ff58ff6d1662c5c43
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
I measured the rise and fall times for I2C bus 1 from userspace
manually, using "i2cdetect 1" called from userspace and an oscilloscope.
This commit fixes the values there to reflect reality.
BUG=b:72442912,b:70232394
Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23459
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change updates the camera power enable GPIOs as per the latest
schematics. With this update, since one of the enable GPIOs is using a
UART0 pin, set UART0 to PchSerialIoSkipInit in devicetree so that
FSP-S does not re-configure the UART0 GPIOs.
BUG=b:68964831
Change-Id: I5d9126ed8ca2b714f6276f4d3a24c243d7654774
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This commit adds support for an Elan touchscreen device connected over
I2C via devicetree.
BUG=b:72121803
TEST=Confirm the device is probed for.
Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
I2C bus configuration is generally set up in devicetree.cb. This change
establishes listings for the buses so that they can be used (though
followup changes should update the buses to have correct timings).
BUG=b:72121803
Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is required to add support for I2C devices on Kahlee to ACPI tables
via devicetree.cb. Without this, operations are not emitted for I2C
devices and the proper ACPI table entries are not generated.
BUG=b:72121803
Change-Id: I1cfe12f3cc23e90ec74b739678f5a5a73257c2c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Chrome OS reports that "GRUNT TEST XXXX" is an invalid hwid. The 8296
comes from the lower four numbers from running:
$ printf "%d\n" 0x$(crc32 <(echo -n 'GRUNT TEST'))
BUG=b:72436450
Change-Id: Ib0044442396cad65c25c107feb35a30a2f70b769
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23411
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This change disables SATA controller in order to make SATA IP enter
low power status.
BUG=b:72332817
TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
and verify SATA IP enters low power state
Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This patch removes IccMax settings from device tree since they
are handled in SoC code from patch e1a75d.
BUG=b:71369428
BRANCH=None
TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot
chromeos-bootimage" & ensure the IccMax settings passed
to FSP are from SoC code.
Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Turn on the load switch to the FP MCU at startup, so the kernel can
detect it and use it.
The load switch enable pin is connected to the GPP_A11 PCH pin (aka
PCH_FP_PWR_EN).
BRANCH=none
BUG=b:71986991
TEST=on Meowth, see the kernel detecting a cros_fp device at startup:
[ 2.133456] cros-ec-spi spi-PRP0001:00: Fingerprint MCU detected.
[ 2.157420] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Change-Id: Id3c40b965a5f018c63481c2e2eea3fc8307352bd
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure the FP MCU interface on GSPI1.
BRANCH=none
BUG=b:71986991
TEST=boot on reworked Meowth with a ZerbleBarn board attached to
GSPI1 and see the cros_ec kernel driver detecting it.
Change-Id: Ib874ddaf4948a766fd05c11f4675dbfdb679059d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for new memory stuffing options that will appear on
the P1 meowth boards.
new strap setting - associated SPD file
----------------------------------------
0b001 - Hynix_H9HCNNN8KUMLHR_1GB.spd.hex
0b010 - Samsung_K4F6E3S4HM_2GB.spd.hex
0b011 - Hynix_H9HCNNNCPUMLHR_4GB.spd.hex
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: Ief07f3de351d01cbc195b785c36e96de0cbf7ddb
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Our current U22 skus (celeron and i3) actually don't support PL2,
but making sure that if we do decide in the future to use it to
make sure PL2 and PsysPl2 values are set appropriately.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 90W with barrel jack for U42
and 65W with barrel jack for U22.
Change-Id: I084d0320128a6e05948023520a30c497c41be23b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
Change-Id: I65173104fce258d03956bbb0e80073c47fe80fab
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Right now the poppy baseboard camera topology allows to add maximum of 2
sensors. The sensors can be of different vendors. The current ASL code
structure doesn't allow sensor customization. Moving PMIC specific objects
from sensor objects to PMIC scope and having separate sensor ASL files will
help in unbinding the PMIC and sensor objects and allow some customizations.
BUG=None
BRANCH=None
TEST=Build and boot soraka, make sure both camera's are working fine
and also verify that the generated DSDT looks fine.
Change-Id: I63ae1a685b78bda212c5c48a4c2dc744164a3cb5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The variant boards can have a custom endpoints, splitting the ASL code
aids customizing the endpoints as per the variant board setup.
BUG=None
BRANCH=None
TEST=build boot soraka, verify that the cameras are working fine and
generated DSDT tables are same as before.
Change-Id: I5f1cded25bfb6a7baf18b211f9773dfecdc2f264
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs that are being set low had the wrong value getting set.
FCH_GPIO_OUTPUT_VALUE was being set instead of FCH_GPIO_OUTPUT_ENABLE.
BUG=b:70234300
TEST=Build and boot Grunt
Change-Id: I16792b76252506a43aac92738b04096ae3fde01c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Grunt and Kahlee touchpads are on different i2c busses; I2CC and I2CD,
respectively.
Since grunt is the 'baseboard', put its configuration under baseboard, and
include it from the grunt variant.
BUG=b:71820409
TEST=Boot grunt to kernel, use evtest to test trackpad.
TEST=Boot kahlee to kernel, use evtest to test trackpad.
Change-Id: I1aeacf9a840342e73c1e219a825b39a124b4dd57
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23232
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Grunt and Kahlee have different audio codecs.
Create a new audio .asl for the baseboard for grunt's codec, link
to it from the grunt mainboard, and move the kahlee codec table
from the baseboard mainboard to its own .asl in variant/kahlee.
Note, we can't use the generic drivers due to the PCI scope
expectation. The AMD I2C are not PCI devices.
BUG=b:69397774
TEST=Codec driver loads. Check dmesg.
Change-Id: I1cc245357d1f3d444e5a5012466eaa5d75d637eb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23226
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the apci/ to the baseboard and move mainboard.asl to
each variant.
BUG=b:71873651
TEST=build
BRANCH=none
Change-Id: I8a829f2946e4b280cd78574eb8dbda6c2a9a1028
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Meowth uses GPD_2 as a dedicated lan_wake pin, so GPD_2 must
be set to use NF1 instead of gpio.
BUG=b:64395641
BRANCH=none
TEST=none
Change-Id: Iadf7158a792dfae0ea5e824d197a558524cdb5fd
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fizz has external Lan on PCIE port.
The Lan device on PCH is not used.
BUG=b:70889517
Change-Id: I99894bedec14a44724ac7c22d0c894132a795b78
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Digitizer power is not controlled by SoC. Also, since the digitizer
uses I2C-HID driver in Linux kernel, the device is put into sleep
anytime system is suspended. Thus, there is no need to control the
reset gpio using ACPI power resource.
TEST=Verified that digitizer device is properly detected on boot-up
and after suspend/resume.
Change-Id: Id11b8412d0ac48b2701d53b0a22ad3b747b544ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Port initializer had been changed from PortDisabled to PortEnabled,
but engine inializer hadn't been updated from PcieUnusedEngine to
PciePortEngine. Update this so the port works.
Also change disabled port to PcieUnusedEngine.
BUG=b:71818026
TEST=PCIe device now shows up on D2F4
Change-Id: I11eb8c1fbad12fa9cf34d758a4ef3c22ef8ba4f7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23210
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If using type-C charger, then PsysPl2 may be lower than barrel jack
value of 90W, so need to override value to the max power of type-C
charger.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 60W with zinger, but 90W
when using proper barrel jack adapter on and i7.
Change-Id: If955b9af0e23f47719f001f1d73ec37113937cea
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The spd.bin file was not getting generated properly, so moved logic
to variant's makefile.
BUG=b:64395641
BRANCH=none
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully and spd.bin is found when booting.
Change-Id: I4642d6ddb5e65f721d1bde31ca0ca5b4438da554
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The .spd.hex text is added to the name by the build process. This
was causing a failure because we were trying to add the files:
'file.spd.hex.spd.hex' to the build.
Remove the additional .spd.hex text.
BUG=b:71535311
TEST=Build
Change-Id: I11df7a90c979503676a66c6502900a13f1a8e359
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure
that required SPD hex files are included in the SPD binary.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I449ab56dfc7a75752944b58ba6291b5ee32f81ad
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/22205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Since the current hardware revision does not have external pull on the
pen eject signal, this change adds internal pull-up on it.
Change-Id: I426d9833d7efbd8735b6f2b4896d1012b62cb4b8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tony Lin <tonycwlin@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Rainier, a scarlet derived board, was configured to use spi0 for tpm
driver by default. This patch switches it to spi2 to reflect recent
changes in scarlet-derived boards.
Change-Id: Ib67109786512c068bb957890f456bccff7addc86
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/23129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Grunt's devicetree dropped some entries when it was split from the
kahlee variant. This commit restores:
spd_addr_lookup - memory information for AGESA
dram_clear_on_reset - keeps DRAM contents on reset
uma_mode - needed for vbios
uma_size - needed for vbios
Change-Id: I1d8cdc97594867f1d706318370055087976a5104
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The spd size of DDR4 is 512, but the size empty.spd.hex is 256.
With empty.spd.hex and DDR4, it will cause mainboard_get_spd_data
loads spd data incorrectly due to the offset is wrong.
Change-Id: Iea3f216898525a2a602fabf1835c8a0c1245ee57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change is to enable SataPwrOptEnable.
With this change, we no longer see SError message in kernel during
suspend_stress_test.
BUG=b:70491485
Change-Id: Ieb991f6889c5ff3181a670bc7702314049fa983c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch revises LED0 Green light behavior from patch 2ecf3f8c.
For 100Mb link speed, LED0 should be OFF.
BUG=b:65437780, b:68284778, b:69950854, b:65808944
BRANCH=None
TEST=Run DUT with 100Mb and 1000Mb ethernet connection and observe
LED0 is behaving as expected.
Change-Id: Ia805c955711b8ce77eba087a28427a005c456fa1
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22964
Reviewed-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
firmware test team is requesting that default gbb flags set to 0x39
rather than 0x239 so that it's consistent with the default gbb flags
of other platforms.
BUG=b:70392534
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage
gbb_utility --get --flags image-fizz.bin and make sure
that it returns 0x39 instead of 0x239
Change-Id: Ib73e4619b13f6b7c2d01598c926fbbd7d7eb9bef
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22962
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is a potential IMVP8 issue for KBL that affects Intersil VRs
Fizz is using one of the affected parts. The fix is to use an updated
microcode and also send a mailbox box command from FSP.
BUG=b:65499724
BRANCH=None
TEST=Build and boot Fizz
Change-Id: Iebfda02df88ea0d2aaf79e8449b95c0eb2165c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It seems that RAM code 0 has been strapped with an incorrect resistor on
Kevin. The resulting voltage divide still puts it well within the ADC
value bucket reserved for that slot, but a little closer to the edge
than necessary. While this doesn't seem to cause any immediate problems
on its own, it still doesn't hurt to fix it (if only for the
documentation value).
On other boards (at least on my Scarlet) the strapping seems to be
correct.
Change-Id: Ic5199834fbeaf734e725ff45b04f45eefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22891
Reviewed-by: David Schneider <dnschneid@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch shifts some comments around to make it easier to replace
values in the ADC strapping bucket table with compile-time conditionals.
Change-Id: Ic51917d3961a51d4e725ff824fb59aeefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
As per the latest schematics, this change configures GPP_B0 for WLAN
wake and uses corresponding gpe bit in ACPI node for WLAN. This hasn't
been tested yet.
BUG=b:70775494
Change-Id: I5198b8083a87d00f890b45986e5e3f62b81686c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22928
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Similar to other KBL projects, this change enables AER and LTR for
root port 1 on poppy.
BUG=b:65570878
Change-Id: Iadad3d2fc46cbba575a776071305925c529a6760
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change really fixes the SataMode to select non-RAID mode and
enables SATA which was incorrectly disabled in a71276b
(mb/google/poppy/variants/nami: Fix SataMode configuration in
devicetree).
BUG=b:70160119
Change-Id: Ied6adabdc1d2458972bde628616a198cd41f9f3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Nami uses DEVSLP1 and not DEVSLP0. This change updates the GPIO
configuration for DEVSLP to match the latest version of schematics.
BUG=b:70160119
Change-Id: Ifa181322011a4b8947ecd0fa44dcf790b0d8f657
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch enables customized NIC leds as below:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:69950854
TEST=Boot on fizz dut and observe the LEDs are behaving as expected.
Perform suspend/resume test and the LEDs are still working as expected.
Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Melfas kernel TS driver (melfas_mip4.c) will look up "ce"
GPIO during driver probe in ACPI _DSD.
But FW does not report "ce-gpios" but "enable-gpios" in _DSD.
Kernel will obtain GPIO from _CRS by index "0" without ID.
Melfas driver does not have separate condition
for MIT-410 so driver will set TS IC power off in probe.
FW now may need to add back "reset" pin in order to hack
this condition to let Melfas driver get "useless" GPIO
so TS IC power (VTSP) will be not off during driver probe by itself.
BUG=b:70149336
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: Icf0451ff0c3df97cb2474e30542a2f46ba67d82a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For Fizz, the default should be AHCI mode and not RAID
mode. Additionally, there is only one drive connector, so
attaching several drives for a RAID is hard.
BUG=b:70146894
Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22837
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
This change selects Kconfig option to disable native SD card
controller in ACPI tables, since it is not used on nami.
BUG=b:70160119
Change-Id: I6180c2b342c69e6a7c357f10b6297d67ea0211d7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add INNOLUX P097PFG panel timing. According to Scalet schematic,
if GPIO3_D4 get low status, it will use INNOLUX P097PFG panel;
if GPIO3_D4 get high status, it will use KD097d04 panel.
Change-Id: I43fa5d859a9a529a84c58a953b37d03953ce648a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move AGESA related headers in soc/amd/common to
soc/amd/common/block/include/amdblocks.
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, headers moved).
Change-Id: I5d3064625ddf8caaf370aabaf93165c6817f1ca0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change provides implementation of variant_memory_params for
nami. Since it uses DDR4 memory, DQ-DQS mapping table is not
required. Also, Rcomp resistor values are provided based on SDP v/s
DDP memory.
BUG=b:70188937
Change-Id: Ic1d0cfdb7d8b02fa0be0a4c54b20057a4c2fc3ce
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change updates scl_lcnt value for I2C5 to bring the bus frequency
closer to 400kHz.
BUG=b:65062416
TEST=Verified that I2C5 frequency is between 389-396kHz.
Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and
spi.c. The remaining files are AGESA related and will be part of a separate
issue/commit.
BUG=b:62240201
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Due to a schematic error, our code was written to configure more I2S0
pins than are actually used. We're also pinmuxing the whole bank of pins
over to the I2S controller even though we don't need them all. Restrict
the GPIO initialization and pinmuxing to the pins we really need so the
other ones can be correctly used as SKU ID pins on Scarlet.
Also, move the "audio" IO voltage domain selection to the other such
selections in the bootblock, since that covers two whole banks of GPIOs
and there's no guarantee that they're all used for audio (and thus not
needed before ramstage).
BUG=b:69373077
TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2.
Change-Id: I9314617e725fe83d254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
These pins need to be pull-ups. I forgot.
BUG=b:69373077
Change-Id: I9314617e01d35898254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds Maxim98357a support for Nautilus using the generic driver
in drivers/generic/max98357
BUG=b:68686020
TEST=With entire merged audio should be enabled on max98357
speaker codec.
Change-Id: I958bf7c1395259b3e3fb30332882fd51a48dc0cc
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Nautilus board uses max989357a speaker codec and 4CH DMIC.
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on Speaker and captures on 4CH DMIC
Change-Id: Ie90af02e0935029f53f9020bd78027b6eb31a187
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the original Chromium source, PcdMemorySpdPtr is only set for
cyan, but none of the other Braswell variants. When upstreamed,
it was left set for all boards as it didn't appear to be problematic.
In wider testing, I came across one reks board for which it caused
FSP memory init to fail, so restricting the parameter to cyan only
as it was originally.
TEST: build/boot google/reks with Micron EDF8132A3MA-JD-F RAM,
observe board now successfully boots where it did not previously.
Change-Id: Iacfbd4bc89fa04717baf85704181d346bca2ed2f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22782
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- The touchscreen interrupt was moved from the GPIO 3, as originally
suggested to GPIO 11. This changes the gevent from 2 to 18.
- Add EMMC reset on GPIO 93.
- Add EMMC bridge PCIe reset on GPIO 40.
- Set device enables to high.
- Remove extra SCI comment from GPIO 130.
- Set individual device PCIe reset pins to high.
- Enable global PCIe reset on GPIO 26.
- Mark LPC_CLK1 as unused.
- Update net names based on latest schematics.
- Set Direction and level/edge correctly for SCIs/SMIs.
- Remove SCI for pen detect.
- Add comments.
BUG=b:70234300, b:69681660, b:69305596
TEST=build grunt
Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on
PCIe port 1, so move the OemCustomize file into the variant directory.
- Add comments in baseboard version so it's easier to understand.
- Update reset pins, put the definitions in gpio.h
BUG=b:70255003
TEST=Build and boot Kahlee. Build Grunt.
Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
This patch makes coreboot set the max current and voltage for barrel jack
adapters.
BUG=b:64442692
BRANCH=none
TEST=Boot Fizz. Use chgsup console command to verify the max current and
voltage are set as expected.
Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22623
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow overriding specific GPIOs by SKU ID. Override two GPIO settings
for nasher to save the power consumption when the system in S0ix.
Change as below:
AVS_DMIC_CLK_A1: IGNORE -> Tx1RXDCRx0.
AVS_DMIC_CLK_B1: IGNORE -> Tx1RXDCRx0.
BUG=b:69025557
BRANCH=master
TEST=compile/verify the power consumption change from ~150mW to ~100mW
on clamshell SKU and from ~200mW to ~100mW for convertible SKU.
Change-Id: I9e0674f206426fddb3947273754774b310106334
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With the old timing, the hblank time isn't large enough,
it may cause display artifacts. So fix it.
BUG=b:70160653
TEST=panel work on Scarlet rev2 board
Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In preparation to deleting early_setup,c, change early_ec_init() to use new
southbridge.c function sb_set_wideio_range and remove <#ifdef __PRE_RAM__>.
BUG=b:64033893
TEST=Build, boot and check serial output, search for "Covered by wideIO xx",
which should match earlier message "Range assigned to wide IO xx" generated
within modified early_ec_init().
Change-Id: Iaea17f4f636aab6bd8b05b1b3bed53a677164e74
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change updates memory SPD handling code in baseboard poppy to
allow variants to define either LPDDR3 or DDR4 memory types. In
addition to that, it also updates the function to print SPD info
considering offsets that might be different across the two memory
types.
BUG=b:70188937
Change-Id: Iefad01719c62264fb0d7e987904e77647d6026c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Until now, nautilus was using the DQ-DQS mappings provided by the
baseboard. However, based on schematics, these values are not
correct. This change adds DQ-DQS mapping tables for nautilus.
BUG=b:70188533
Change-Id: Ife6ba19b8fe8873ab8cca977ca8f34a4d86e8e6e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22706
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: shkim <sh_.kim@samsung.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch switches the board_id and ram_code helper framework to use
weak functions rather than Kconfigs to determine whether the board
supplies these IDs. This cuts down on the amount of boilerplate Kconfigs
many boards have to set and also gives them more flexibility, such as
being able to determine at runtime whether a given ID is present.
Change-Id: I97d6d1103ebb2a2a7cf1ecfc45709c7e8c1a5cb0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22695
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Merge the different coreboot table strapping ID structures into one
because they're really just all the same, and I want to add more. Make
the signature of the board_id() function return a uint32_t because
that's also what goes in the coreboot table. Add a printk to the generic
code handling strapping IDs in ramstage so that not every individual
mainboard implementation needs its own print. (In turn, remove one such
print from fsp1_1 code because it's in the way of my next patch.)
Change-Id: Ib9563edf07b623a586a4dc168fe357564c5e68b5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The BOARD_ID_MANUAL and BOARD_ID_STRING options were introduced for the
Urara board which is now long dead, and have never been used anywhere
else. They were trying to do something that we usually handle with a
separate SKU ID these days, whereas BOARD_ID is supposed to be reserved
for different revisions of the same board/SKU. Get rid of it to make
further refactoring of other options easier.
Also shove some stuff back into the Urara mainboard that should've never
crept into generic headers.
Change-Id: I4e7018066eadb38bced96d8eca2ffd4f0dd17110
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22694
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variants nautilus and soraka currently provide the exact same
definition for variant_cros_gpios as provided by the baseboard. This
change removes the function defintions from variants so that the weak
definition in baseboard can be used.
Change-Id: Ic88623f34039792f0f9fb46842b24e4f1290981b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22705
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a new config option VARIANT_HAS_CAMERA_ACPI to allow
variants to define ACPI tables for camera support. It also prevents
boards that do not need this from unnecessarily providing dummy files
for camera ACPI support.
Change-Id: I91f8e407e0f021071eeadbde8c2695e2a6d69e06
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change the prefix for TPM options from POPPY_USE_* to
VARIANT_HAS_*. This makes it clear that these are variant specific
options.
Change-Id: I6fd120a34a5b0c1f018164d5c2b60548da1d0f61
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to allow variants to select different Kconfig options, this
change adds VARIANT_SPECIFIC_OPTIONS_${VARIANT_NAME} which can be
selected by each variant in Kcnonfig.name.
Change-Id: I15db2fdac5c9e55f9698c8a0c083d6467afae245
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change removes the dynamic disabling of TPM based on config
options. Poppy and its variants will have only one type of TPM
supported and so there is no need to update it dynamically.
Change-Id: Ie82825fcf7092e845583edaac9ba0d3fc9d1dd80
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22704
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the USB over current pins for the Grunt baseboard and
Kahlee mainboard. Removes the ACPI ASL OC code, which is not
used on Stoney Ridge SOC.
BUG=b:69229635
TEST=Build and boot Kahlee. Not tested with OC test fixture.
Change-Id: I5a9b3409d9c91b89fd02f8eecf9e04c435f14342
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
There is some confusion with old RAMID table, make it clear,
and let's no longer tangle it in future.
Change-Id: I44215b4a6668074575a5df691ac1ff8fa3d15492
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch enables WOL feature.
BUG=b:69290148
BRANCH=None
TEST=powerd_dbus_suspend && sudo etherwake -i eth0 $MAC to make sure
the system could be woken up by WOL packet.
Change-Id: I1178a776db2cdb448fe6650d49ae6c0281ac1128
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Lava numbers are in.
BUG=b:69990330
BRANCH=none
TEST=verified that USB signal is within spec
Change-Id: I7416ec8d058271700ebe43f8d92af61c6c0d6b42
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These files aren't needed for the overcurrent functionality.
BUG=b:69305596, b:69229635
TEST=Build Grunt & Kahlee. Overcurrent wasn't yet enabled so no other
testing was needed.
Change-Id: I8dcd50a249e387ccf1142949b359cee09942460a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Update the variable ${CONFIG_VARIANT_DIR} to use parens instead. Either
is valid, but since we use parentheses everywhere else, it's better to
be consistent.
BUG=b:69691210
TEST=Build grunt & kahlee
Change-Id: Ieffabaae5516a893f1dc1f7195a17c4cdeae8853
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22656
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change disables DPTF until the support is properly added in
dptf.asl
Change-Id: I68f2442e00718a4edbb34661d31d3a415d41c29f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I6246300a4376a0194950d4de277af040b10b6c1f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add synaptics touchscreen in the device tree so that the correct ACPI
device is created.
BUG=b:66462881
BRANCH=master
TEST=compiled/verify the touchscreen works
Change-Id: I6e89a5db0e9f8ae777eed661f3bf89d653a937e6
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the mainboard_spd_read function in romstage and call the variants
function. Grunt is the baseboard and has soldered down memory, so add
it for the default weak SPD functions and build the SPDs in cbfs.
Kahlee overrides the weak SPD function and falls back to the soc
I2C SPD functions.
BUG=b:67845441
TEST=Build and boot Kahlee.
Change-Id: I789002bfadc1a2b24f9046708986d29c0e2daf33
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The GPIOs used in board_id are meant to indicate the memory
configuration. Rename board_id to memory_skus.
Report the board_id received from the EC.
BUG=b:69649438
Change-Id: I84bacead3daf829c97f595c4c11a243953243c29
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22561
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change disables camera devices until camera support is properly
added for nautilus.
Change-Id: I7de37cbf9c32fa063f55a2e54986e33b66acfa3b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds infrastructure to allow variants to define their own
camera.asl file.
- Poppy and soraka use the one provided by baseboard.
- Dummy file is added for nautilus since it does not have camera
support enabled yet.
TEST=Verified that DSDT table remains the same with and without this
change.
Change-Id: I0f0b489e74739aa4708283d58d8b7626b77a89a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: shkim <sh_.kim@samsung.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Support kd097d04 dual mipi panel on Scarlet.
Change-Id: Ie8bc0cbb79840f1924a8cc111f2511292203731f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
it uses backlight enable pin as backlight gpio currently,
correct it and define the right backlight gpio.
Change-Id: I7c5abfd5bbbae015b899f3edc8892ea32bf82463
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Refactor the mipi driver, so we can support dual mipi panel.
And pass the panel data from mainboard.c, that we can
support different panel with different board.
Change-Id: Id1286c0ccbe50c89514c8daee66439116d3f1ca4
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add "speed_config" for each I2C port configuration to set speed to
400KHz.
BRANCH=master
BUG=none
TEST=compiled/verified
Change-Id: Icb48733b87cefc92577547b1eab661a8cbb12be6
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22589
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On shutdown, Soraka enters Deep S5 and not S5 state. Setting
pad reset config of a gpio to RSMRST will not preserve
the gpio config across deepSx and the gpio should be configured again.
The WLAN_PE_RST signal should be brought up early in the bootflow
for giving the device enough time to initialized before PCIE init in FSP-S.
Hence, the gpio WLAN_PE_RST (GPP_B8) pad configuration is done in
early pad configuration in bootblock also.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S5, S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I5c7a4a3871a3bff69c1136379c78a8368c6258a6
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
- Remove SI_ALL section. This is no longer needed as the PSP dirctory
is placed into the RO coreboot section.
- Add 1MB Legacy section.
- Add Memory cache section. These sections are called "MRC", which is
an Intel term, but AMD platforms will use the same regions for saving
the same sort of data.
BUG=b:65497959, b:67035984
TEST=Build & boot kahlee
Change-Id: I5e41a0aa6bd4b29b8014c6559126a29cd7ed45d8
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Follow the schematic and Doc 573387 to correct the rcomp and
rcomp target settings for fizz
TEST= boot ok and the system can enter and resume from S3.
Change-Id: Iffa90461509cfadaca20e335a6655e549e79e749
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We are disabling tpm over i2c, so the configs are not needed
anymore.
BUG=b:65056998
BRANCH=None
TEST=emerge fizz and make sure can still boot up.
Change-Id: Id88f32fa952801749544534442fc15d85fc1a892
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
As cr50 has now switched to using SPI, no need to enable the i2c1
anymore. Additionally, disabled unused I2C devices -- I2C0, I2C2 and
I2C3.
BUG=b:69374421
BRANCH=None
TEST=test on fizz celeron. Make sure /dev/tpm0 created on (many)
reboots. cat /proc/interrupts. Make sure # interrupts for 16
after booting is reasonable (not > 10k) and idma64.0,
i2c_designware.0 are not listed with that interrupt line anymore.
Should look something like this:
16: 1174 0 IO-APIC 16-fasteoi i801_smbus, snd_soc_skl, AudioDSP
Change-Id: Iac3e31264a937a1d7ed6bd41632e7e065317781b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some Google boards are missing this selection, leading them to being
incorrectly identified as type 'Desktop' in SMBIOS type 3 table.
Correct this by adding 'select SYSTEM_TYPE_LAPTOP' to the boards'
Kconfigs.
TEST: boot Linux and check correct chassis type listed via dmidecode
Change-Id: Ib1145e314812a3f300cfd1a435a687aa0862158a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These typos were found through manual review and grep.
Change-Id: Ia5a9acae4fbe2627017743106d9326a14c99a225
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently, mosys just returns "fizz" as model/chassis values.
Returning proper OEM IDs so that mosys can return the proper
variant.
BUG=b:67732053
BRANCH=None
TEST=mosys platform model; mosys platform chassis;
Make sure returns the right variant string and not fizz.
Change-Id: I42e293e833b0f7c9870dc275561ad13256836e60
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ChromeEC is getting ready to bump up the hostevents and wake masks to
64-bits. The current commands to program hostevents/wake masks will
still operate on 32-bits only. A new EC host command will be added to
handle 64-bit hostevents/wake masks. In order to prevent individual
callers in coreboot from worrying about 32-bit/64-bit, the same API
provided by google/chromeec will be updated to accept 64-bit
parameters and return 64-bit values. Internally, host command handlers
will take care of masking these parameters/return values to
appropriate 32-bit/64-bit values.
BUG=b:69329196
Change-Id: If59f3f2b1a2aa5ce95883df3e72efc4a32de1190
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Rainier is a scarlet-derived board but uses eDP as opposed to MIPI. Using
GRU_BASEBOARD_SCARLET is enough, except for display related logic. In
those cases, use board specific logic instead of baseboard.
Change-Id: I596f7ca6bc26312ecaeb261c96cebd46974c2cdf
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/22542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Request from commit 519680948b (move carrizo_fch.asl code to soc), merge
several includes into a single file in soc directory.
Rename soc_fch.asl to sb_fch.asl. Rename fch.asl to sb_pci0_fch.asl.
Then copy the required section from dsdt.asl into a new soc.asl.
Affected boards: amd/gardenia and google/kahlee.
BUG=b:69368752
Change-Id: I83d850cf9457f7c2c787336823d993ae2e9d28ce
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22541
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit c09c2a4 [mb/google: Add Chromebook marketing names] added
marketing names for many ChromeOS devices; add some that were left out,
correct some errors, and try to format model names/numbers consistently
(or as consistently as the manufacturers allow).
Change-Id: Ia13858e2e6ba7d7e025f25fad33e6338250498e5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable separate MRC cache for recovery mode. This requires change in
flash layout to accomodate another region for RECOVERY_MRC_CACHE.
BUG=b:69473883
TEST=Verified following scenarios:
1. Boot into recovery does not destroy normal mode MRC cache.
2. Once recovery MRC cache is populated, all future boots in recovery
mode re-use data from the cache.
3. Forcing recovery mode to retrain memory causes normal mode to retrain
memory as well.
Change-Id: Icdfac3698507d89d98a51cfc3d756a56d2a2d648
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is merit in having new boards use the pinouts and controls
in scarlet. This adds a config so new scarlet-derived boards can
easily use scarlet structure without going through every file
and adding new logic.
TEST=Run "emerge-scarlet coreboot"
Signed-off-by: egemih@chromium.org
Change-Id: I5808f93f4563033ce93050e1eedb6eac2b52c3b3
Reviewed-on: https://review.coreboot.org/22517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Remove ugly camel case in the soc/amd/common and Stoney Ridge
SPD files and functions. Update the related mainboards.
Also, remove a unreferenced function prototype, smbus_readSpd().
Change-Id: I51045b6621f0708d61a570acbdcb4e6522baa1ea
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The mainboard directory is included through the PI makefile - most
mainboard directories aren't in the include path at all. Move the
ec.h file into the baseboard/variant directory that is already in
the include path.
BUG=b:69220826
TEST=Build
Change-Id: I89d361b700c66ba576de724927574fdab9461fc6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All AGESA headers should be included only through agesawrapper.h
I missed this file in the Kahlee cleanup.
BUG=b:66818758
TEST=Build gardenia; Build & boot kahlee
Change-Id: Id9b303cb3cee8088fb5cca5257566c033d28c692
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This fixes some issues with the initial implementation that was copied
from reef.
- The board ID value shouldn't be size_t - it's not a size.
- Kahlee doesn't even need the memory.c file - it uses an SoDIMM.
BUG=b:68293392
TEST=build stoney platforms, boot kahleebo
Change-Id: Ife5660d36912e887edfd0365a9f16c5a172c9c86
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22515
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's sometimes hard to find the code name of a Chromebook. Add the
marketing names to Kconfig, since they are easily available.
Information (mostly) taken from:
https://www.chromium.org/chromium-os/developer-information-for-chrome-os-devices
Unknown boards (unreleased, etc.):
* Fizz
* Foster
* Nasher, Coral
* Purin
* Rotor
* Rowan
* Scarlet, Nefario
* Soraka
* Urara
* Veyron_Rialto
Baseboards:
* Glados
* Gru
* Jecht
* Kahlee
* Nyan
* Oak
* Poppy
* Rambi
* Zoombini
White label boards:
* Enguarde
* Heli
* Relm, Wizpig
TODO: How does this interact with the board_status code?
Change-Id: I20a36e23bd3eea8c526a0b3b53cd676cebf9cd86
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set the EC SCI reporting mask to include the power plug reporting.
BUG=b:65637324
TEST=Check power_supply_info on AC/DC.
Change-Id: I58814fc495081ffe8e47162da0fa4fbeba49d67b
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Code within carrizo_fch should be SOC specific instead of board specific.
BUG=b:64034810
Change-Id: I5de2020411794bfcd3730789f62af9c9834a018b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22455
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This feature was enabled at the kernel level, but that is triggering an
issue where FSP expects it to be disabled so it forces a cold reboot on
every warm reboot. Since we want this enabled anyway just set it this
way in the BIOS so it matches what the kernel expects.
BUG=b:68666100
TEST=pass firmware_FWtries on Eve with R63 OS image
Change-Id: I294e34d25406365d591da06ce4c931b710cfbbaa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: I964d3d30392d130e808f37a661f2c89ec926cf58
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/749733
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tune PCH I2C4 hold times to ensure the frequency is always <400KHz.
BUG=b:67029862
TEST=boot on eve and measure I2C4 at Tp262 to be 385KHz
Change-Id: Ie93c5c40bc74069b285f6c3ee311f1bd7cefcaf1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Iceabc806a17b9e6a144a4f6288c6cca790d03950
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/739841
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AER and LTR must be enabled individually on ports that need it,
in this case it should be enabled for WiFi and NVMe.
BUG=b:65457528
TEST=Wifi team verified that the performance is better with these changes.
Change-Id: I0d688fe07a1f3117c1ca617c2ce78e0d024a3510
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ib059517fa782ccc18ba5ef1f76058a1898b7bf7a
Original-Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/671211
Original-Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Commit-Queue: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/22447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the rt5663 driver and provide values for the offsets which are
needed for providing manual values to compensate the DC offset for
L and R channels between headphone and headset.
BUG=b:62712227
TEST=build and boot on eve and ensure rt5663 is functional.
Change-Id: I88113616e4b7c79cff840168b7c54ae754dfa75f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ica4090636c1ff29f0298114e62c9cc6fe167a425
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/611606
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Hsinyu Chao <hychao@chromium.org>
Reviewed-on: https://review.coreboot.org/22446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change the touchscreen power control back to coreboot instead of
under the ACPI _ON/_OFF methods, and switch the TOUCHSCREEN_STOP_L
pin back to an output.
This reverts previous changes to touchscreen GPIOs that were made
to get back to a known good/working state. Having ACPI control these
pins was resulting in a small percentage of touchscreen not being
discovered at boot. This platform is not intending to use S0ix so
the ACPI control is not needed.
BUG=b:63718744
TEST=manual testing on Eve devices.
Change-Id: I3fd64a435a053da1558ef736fe7baceee3c8f3a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ia1e2ae7ca2a8b668c60fbda2aa50373e580646b2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/572692
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Commit-Queue: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/22445
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
All Stoney AGESA headers should be included only through agesawrapper.h
BUG=b:66818758
TEST=Build and boot tested
Change-Id: I642f5caf8a37ae4042c32fec3a92e0995193cb7a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of getting the address of the GPIO function with an extern,
add a getter function and make the GPIO arrays static.
TEST=Build Grunt; Build & boot Kahlee
BUG=b:69164070
Change-Id: I3defcb66696459b915d7d4f43234d5c08ab7d417
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
mainboard.h only had a single function definition. Move it into
baseboard/variants.h and get rid of the file.
TEST=Build grunt/kahlee
BUG=b:69164070
Change-Id: I6b7d50d5c949733d77c42b4daf56ed1f97ed6954
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update common files and add files for grunt to the variant directory.
BUG=b:68293392
TEST=Build only
Change-Id: I7b80e470058872d6613e66e64c8dd1494942e9b9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Several SPD hex files for chell were missing from upstream coreboot
(as compared to the Chromium tree/branch), which resulted in the
incorrect type and amount of RAM being reported on chell boards
with > 4GB RAM. Add these missing files and their Makefile entries.
TEST: boot google/chell m7/16GB config and observe correct RAM
type and amount reported via dmidecode and cbmem console log.
Change-Id: I37d708c96e754b438e40fc413420aa64bf234c29
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22402
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the UMA memory size to 128 MiB. This value was empirically tested
by AMD as the lowest value one could use.
BUG=b:64927639
TEST=default, and 64, 128, 256, 384MB non-legacy configurations.
Change-Id: I2bc808d8b402c3eb16a1a5962f3fa9d6b224cf52
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/21335
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a #define for MB_DIMM_SLOTS and verify it doesn't exceed the max
supported for the device. AGESA's DRAM procedures follow the BKDG and
may vary depending on the number of slots on the motherboard. DIMM
numbering and ordering is also affected by this value.
Replace hardcoded integers with defined values for DIMM slots and
number of channels.
Change-Id: I4f7336da80b4e3d7f351502a63de0652e9ff5395
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21853
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kahlee needs to keep its DRAM contents after a reset. Move this
override out of the OemCustomize.c file to a devicetree register
setting.
Change-Id: I3196cb8b94bec64e8ce59e4285cf8d97f442bd3d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/21858
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Astronaunt, after the system enters the S5 power state, there is a
10-second timeout before the system transitions the power state from S5
to G3. The EN_PP3300_DX_LTE_SOC signal, which is controlled by GPIO_78
on the APL platform, remains on during that period. If the system is
powered back on before going to G3, the built-in modem won't go through
a power cycle as EN_PP3300_DX_LTE_SOC is never de-asserted.
Keeping the modem, and indirectly the SIM, powered during a quick system
power cycle may sometimes be undesirable. For instance, we would like a
SIM with PIN lock enabled to require unlocking each time the system is
powered on. After the SIM receives a PIN, it may remain unlocked until
its next power cycle.
Also, it is often desirable to power cycle the modem when the system
goes through a power cycle. For instance, a user may power cycle the
system to recover a wedged modem.
BUG=b:68365029
TEST=Tested the following on an Astronaunt device:
1. Verify that the modem is powered on after the system boots from cold.
2. Suspend the system to S0ix. Verify that the modem remains powered on
when the system is in S0ix. After the system goes back to S0, verify
that the SIM with PIN lock enabled doesn't request unlocking, and the
modem can quickly reconnect to a network.
3. Configure the system to suspend to S3 instead of S0ix, and then
repeat (2).
4. Perform a quick system power cycle, verify that the modem is powered
cycle and the SIM with PIN lock enabled requests unlocking.
Change-Id: Ie60776d5d9ebc6a69aa9e360bd882f455265dfa2
Signed-off-by: Ben Chan <benchan@chromium.org>
Reviewed-on: https://review.coreboot.org/22415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch enables customized NIC leds as follows:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:65437780, b:68284778
TEST=Make sure the registers are programmed as expected and observe the
LEDs are behaving as expected. Perform suspend/resume test and the
LEDs are still working as expected.
Change-Id: I9bb1367a4c742c2755d620e14ee6dfe70ee7f34b
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
