Intel common PCI driver is handle PCI subsystem ID
programming, hence no need to have an explicit soc
function to do the same.
TEST=PCI subsystem id is getting programming during
pci enumeration.
Change-Id: Iead57a286b26d532e578cfff99f412c23fd4c2fe
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to the PCH BIOS Spec (Doc#549921/Rev-2.3.4),
section 2.5.1.6, it is a requirement to program the same
value programmed in LPC "PCI offset 82h" into "PCR[DMI]+2774h"
to fully enable the Lpc IO enable decoding which is missing in
current source.
Without above changes, Skylake Saddlebrook platform with a
SIO does not boot.
Change-Id: Ief26e2718325b9d74ea0f83d47d2f917e0972173
Signed-off-by: praveen <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/22819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures that all required information for
pch/mch/igd deviceid and revision available in single
stage and make use of local references.
TEST=Build and boot soraka/eve
Change-Id: I6f7f219536831210750a486ee3b3308d6f285451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22756
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
PCI resources MMIO space/bus master enabling is handled inside
pch_dev_enable_resources() from common device code. Hence
no need to have an explicit soc function to do the same.
TEST=lspci from kernel console shows same pci device list
without and without this patch.
Change-Id: I005e486dd435e9c61ae3f5dfe3ff0e8f688d16e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This partially reverts commit a7b97510ae.
For the internal eMMC to be used by Windows for installation,
the CARD device and _RMV methods are required. Without them,
Windows does not see/show the eMMC as a valid installation
target.
TEST: boot google/chell with Tianocore payload and install
Windows 10 to the internal eMMC drive.
Change-Id: I04819ff16ab4cb0d2ea6e1c7f47179f5dacb7cfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22684
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I94d09a28bf1ea07a53cfa04c54752358bafca610
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the ACPI DBG2 table generation for Intel boards. This is
a Microsoft defined ACPI extension that allows an OS to know what
the debug port is on a system when it is not enabled by the
firmware, so it does not show up in the coreboot tables and
cannot be easily found by a payload.
broadwell: Use byte access device, set up only when enabled since
it relies on the port being put in byte access mode and using
this serial port for debug was not standard in this generation.
skylake: Enable for the configured debug port. Skylake uses
intelblocks for UART but not ACPI.
common: Enable for the configured debug port. This affects
apollolake and cannonlake.
Tested by compiling for apollolake/broadwell, tested by reading
the DBG2 ACPI table on kabylake board and using IASL to dump:
[000h 0000 4] Signature : "DBG2"
[004h 0004 4] Table Length : 00000061
[008h 0008 1] Revision : 00
[009h 0009 1] Checksum : 3B
[00Ah 0010 6] Oem ID : "CORE "
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 00000000
[024h 0036 4] Info Offset : 0000002C
[028h 0040 4] Info Count : 00000001
[02Ch 0044 1] Revision : 00
[02Dh 0045 2] Length : 0035
[02Fh 0047 1] Register Count : 01
[030h 0048 2] Namepath Length : 000F
[032h 0050 2] Namepath Offset : 0026
[034h 0052 2] OEM Data Length : 0000
[036h 0054 2] OEM Data Offset : 0000
[038h 0056 2] Port Type : 8000
[03Ah 0058 2] Port Subtype : 0000
[03Ch 0060 2] Reserved : 0000
[03Eh 0062 2] Base Address Offset : 0016
[040h 0064 2] Address Size Offset : 0022
[042h 0066 12] Base Address Register : [Generic Address Structure]
[042h 0066 1] Space ID : 00 [SystemMemory]
[043h 0067 1] Bit Width : 00
[044h 0068 1] Bit Offset : 00
[045h 0069 1] Encoded Access Width : 03 [DWord Access:32]
[046h 0070 8] Address : 00000000FE034000
[04Eh 0078 4] Address Size : 00001000
[052h 0082 15] Namepath : "\_SB.PCI0.UAR2"
Change-Id: If34a3d2252896e0b0f762136760ab981afc12a2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add APIs and required parameters for creating Dialog da7219 SSP
endpoints in NHLT table.
The use of a NHLT table is required to make audio work
on the kabylake SoCs employing the internal DSP. The table
describes the audio endpoints (render vs capture) along with
their supported formats.
BUG=b:68686020
TEST=check that NHLT table for da7219 is created properly
Change-Id: I57b88873f1c59c8aadf8eec3c80a9d95165a2cc3
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The padding has recently been broken in commit 90ebf96df5
("soc/intel/skylake: Add GNVS variables and include SGX ASL") and fixed
again in commit af88398887 ("soc/intel/skylake: Fix broken GNVS offset
for chromeos"). Avoid this bug in the future.
Change-Id: I1bf3027bba239c8747ad26a3130a7e047d3b8c94
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change 90ebf9 (soc/intel/skylake: Add GNVS variables and include SGX
ASL) added new GNVS variables but did not adjust the unused array size
and thus broke chromeos offset.
This change fixes the above issue by reducing the size of unused
array.
BUG=b:68254376
TEST=Verified that chromeos offset is correct. crossystem is able to
read all variables.
Change-Id: I5f76f5bba4f0f50a23a863450743385ad2a82b2b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22176
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit just moves the vboot sources into
the security directory and fixes kconfig/makefile paths.
Fix vboot2 headers
Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Librem13v2 needs to set this parameter to work around
power-related issues with some SATA devices.
Change-Id: I7fcef36ec8662e18834394b72427a0633c6b7e92
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22045
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The ME status is the interpretation of the status registers, but
having the actual status registers printed is important and it doesn't
hurt to show them.
Change-Id: I6ef3401b36fedfa8aed14f4a62bdbec3d8c6d446
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/21960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
- Call sgx_fill_gnvs to update GNVS data, if
CONFIG_SOC_INTEL_COMMON_BLOCK_SGX is set.
- With this patch SGX ACPI device would get pached with enumaretd values
of ECP device status, base address and length
Change-Id: Ief0531fbab34838a3f8adb9cdc7d3fe19203c432
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Add GNVS variables for SGX
- Include SGX ASL if CONFIG_SOC_INTEL_COMMON_BLOCK_SGX is set
- With this patch SGX ACPI device would get created and kernel SGX
driver would let loaded
Change-Id: Ie95eb79a01e1c0005e0f137b015b7fe000c1ab2a
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Avoid calling calculate_dram_base() function to get chipset reserved
memory size during pci resource allocation. Rather use EBDA to store
chipset reserved memory size while calling cbmem_top_int().
This patch avoids one extra calculate_dram_base() call.
BRANCH=none
BUG=b:63974384
TEST=Ensures DRAM based resource allocation has taken care of Intel
SoC reserved ranges.
Change-Id: I52f359db5a712179d7f2accb4d323d759f3b052b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If GPE_STS indicates that the wake source is internal PME, but none of
the controllers have the PME_STS bit set, then try probing individual
XHCI ports to see if one of those was a wake source. In some cases
e.g. gsmi logging with S0ix, pci_pm_resume_noirq runs before gsmi
callback and clears PME_STS_BIT in controller register. In such cases,
xhci port status might provide a better idea about the wake source.
BUG=b:67874513
Change-Id: I841bb2abccfa9bd6553c1513e88a6306b40315e4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Ensure that port_status read is not all 1s to ensure that read from
mmio address returned valid data.
2. If device connect/disconnect shows that it was a wake source, there
is no need to check for usb activity.
BUG=b:67874513
Change-Id: Id8b4a1fec7bfe530fe435a0f52944b273cdd89ad
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds a mask to allow SMI handlers to be run even in SCI
mode. This prevents any SMI handlers from accidentally taking
unnecessary action in SCI mode.
Add APM_STS and SMI_ON_SLP_EN_STS to this mask to allow gsmi and sleep
to work in SCI mode.
BUG=b:67874513
Change-Id: I298f8f6ce28c9746cbc1fb6fc96035b98a17a9e3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds support for logging wake source information in gsmi
callbacks. With this change, all the elog logging infrastructure can
be used for S0ix as well as S3 on skylake.
BUG=b:67874513
Change-Id: Ie1f81e956fe0bbe2e5e4c706f27997b7bd30d5e0
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change moves soc_fill_power_state and soc_prev_sleep_state to
pmutil.c. It allows the functions to be used across romstage and smm.
BUG=b:67874513
Change-Id: I375ac029520c2cdd52926f3ab3c2d5559936dd8c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22085
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change allows the same functions to be used across ramstage and
smm without having to add checks for what stage is using it.
BUG=b:67874513
Change-Id: I3b10c9e8975e8622d8cb0f66d90d39a914ba7e1c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's possible for chipsets utilizing ebda to cache the cbmem_top()
value to be called prior to the object being entirely setup. As
such it's important to check the signature to ensure the object
has been initialized. Do that in a newly introduced function,
retrieve_ebda_object(), which will zero out the object if the
signature doesn't match.
Change-Id: I66b07c36f46ed9112bc39b44914c860ba68677ae
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
If FSP 2.0 is used, then postcar stage is used and the flashconsole
as well as spi drivers needed to be added.
Change-Id: I46d720a9d1fe18a95c9407d08dae1eb70ae6720e
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/21959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable the use of the SataPortsEnable and SataPortsDevSlp registers
which were being ignored from the devicetree and were not affecting
the resulting UPD parameters.
SataPortsEnable was only being copied for the first SATA port, while
the other ports were left ignored.
Change-Id: Iae70a4d6375fa5d1b05ee89f6b97c65dbbf28dda
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/21958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Update gpe handling function names to explicitly mention if they
are operating on:
a. STD GPE events
b. GPIO GPE events
c. Both
2. Update comment block in pmclib.h to use generic names for STD and
GPIO GPE registers instead of using any one platform specific names.
BUG=b:67712608
Change-Id: I03349fe85ac31d4215418b884afd8c4b531e68d3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21968
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change d3476809 (soc/intel/skylake: Add support in SKL for PMC common
code) changed the logic for obtaining previous sleep state by
unconditionally checking for PWR_FLR and SUS_PWR_FLR. In case of deep
S3, SUS_PWR_FLR is set in gen_pmcon_b (just like resume from deep
S5/G3) and hence the check for power failure should be done only when
WAK_STS bit is not set. This is necessary to differentiate wakes from
deep S3 and G3.
This change restores the original logic by performing power failure
check only in cases where WAK_STS bit is not set.
BUG=b:67617726
TEST=Verified following:
1. When WAK_STS bit is not set and SUS_PWR_FLR is set, coreboot
correctly identifies that the system prev sleep state was S5.
2. When WAK_STS bit is set and SUS_PWR_FLR is set, coreboot correctly
identifies that the system prev sleep state was S3.
Change-Id: Ic97bbc9911ba34aa21f4728c77fc20c5bb08f6f9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update FSP header files to version 2.7.2.
New UPDs added
FspmUpd.h:
*CleanMemory
FspsUpd.h:
*IslVrCmd
*ThreeStrikeCounterDisable
Structure member names used to specify memory configuration
to MRC have been updated, SoC side romstage code is updated
to handle this change.
CQ-DEPEND=CL:*460573,CL:*460612,CL:*460592
BUG=b:65499724
BRANCH=None
TEST= Build and boot soraka, basic sanity check and suspend resume checks.
Change-Id: Ia4eca011bc9a3b1a50e49d6d86a09d05a0cbf151
Signed-off-by: Balaji Manigandan B <balaji.manigandan@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/21679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable Skylake to use the new common LPC code. This
will help to reduce code duplication and streamline code bring up.
Change-Id: I042e459fb7c07f024a7f6a5fe7da13eb5f0dd688
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Other than switch to use common gpio implementation for skylake based
platform, also apply the needed changes for purism board.
Change-Id: I06e06dbcb6d0d6fe277dfad57b82aca51f94b099
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/19201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
IMGU and CIO2 devices do support the hardware managed cache
coherency and hence removing the CCA object which was
reporting that cache coherency is not supported.
BUG=none
BRANCH=none
TEST=Build and boot soraka. Dump ACPI tables and verify that
CCA object is not present.
Change-Id: I14b0a92eafe193e9004d2dad0957a3fe8d05d313
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/21678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch implements soc override function to calculate reserve memory
size (PRMRR, TraceHub, PTT etc). System memory should reserve those
memory ranges.
BRANCH=none
BUG=b:63974384
TEST=Ensures DRAM based resource allocation has taken care
of intel soc reserved ranges.
Change-Id: I19583f7d18ca11c3a58eb61c927e5c3c3b65d2ec
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch uses BIOS EBDA area to store relevent details
like cbmem top during romstage after MRC init is done.
Also provide provision to use the same EBDA data across
various stages without reexecuting memory map algorithm.
BRANCH=none
BUG=b:63974384
TEST=Ensures HW based memmap algorithm is executing once in romstage
and store required data into EBDA for other stage to avoid redundant
calculation and get cbmem_top start from EBDA area.
Change-Id: Ib1a674efa5ab3a4fc076fc93236edd911d28b398
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds the support for Kabylake Celeron base SKU
with PCH ID 0x9d50.
BRANCH=none
BUG=b:65709679
TEST=Ensure coreboot could recognize the Kabylake Celeron base
SKU and boot into OS.
Change-Id: I9c6f7bf643e0dbeb132fb677fcff461244101a55
Signed-off-by: Tsai, Gaggery <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quantatw.com>
Reviewed-by: T.H. Lin <T.H_Lin@quantatw.com>
There are a lot errors reported by AER driver for root port 0.
The erors are being caused by an unsupported request from the
device to the upstream port. Enabling LTR on the root port stops
these errors, it is because LTR is enabled on the device side but
not on the root port and hence root port was logging the LTR messages
from the device as unsupported.
The PCIe base spec (v3.1a) section 6.18 also states that:
LTR support is discovered and enabled through reporting and control
registers described in Chapter 7. Software must not enable LTR in an
Endpoint unless the Root Complex and all intermediate Switches indicate
support for LTR. Note that it is not required that all Endpoints support
LTR to permit enabling LTR in those Endpoints that do support it. When
enabling the LTR mechanism in a hierarchy, devices closest to the
Root Port must be enabled first.
If an LTR Message is received at a Downstream Port that does not
support LTR or if LTR is not enabled, the Message must be treated
as an Unsupported Request. FSP has a UPD for enabling/disabling
LTR on root port, use the same for configuring LTR on PCIe root ports.
BUG=b:65570878
TEST=After enbaling LTR on port 0 on the MB devicetree, No errors reported
by AER driver for root port 0.
Change-Id: Ica97faa78fcd991dad63ae54d2ada82194b4202a
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/21547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There's an occasional issue on machines which use CMOS for their
vbnv storage. The machine that just powers up from complete G3
would have had their RTC rail not held up. The contents of vbnv
in CMOS could pass the crc8 though the values could be bad. In
order to fix this introduce two functions:
1. vbnv_init_cmos()
2. vbnv_cmos_failed()
At the start of vboot the CMOS is queried for failure. If there
is a failure indicated then the vbnv data is restored from flash
backup or reset to known values when there is no flash backup.
BUG=b:63054105
Change-Id: I8bd6f28f64a116b84a08ce4779cd4dc73c0f2f3d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to prepare for checking RTC failure in the early boot
paths move the rtc failure calculation to pmutil.c and add a helper
function to determine if failure occurred.
BUG=b:63054105
Change-Id: I88bf9bdba8c1f3a11bc8301869e3da9f033ec381
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21554
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of having each potential caller deal with the differences
of cmos_init() and init_vbnv_cmos() when VBOOT is enabled put the
correct logic within the callee, cmos_init(), for handling the
vbnv in CMOS. The internal __cmos_init() routine returns when the
CMOS area was cleared.
BUG=b:63054105
Change-Id: Ia124bcd61d3ac03e899a4ecf3645fc4b7a558f03
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21549
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UNCORE PRMRR BASE and MASK MSRs are not common, so move to
SOC specific header file and rename the #define to start with MSR_*
Change-Id: I799c43f0b7a9eec5b3b69ab0f5100935c7f3f170
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
To remove chip.h dependency from SGX common code
- Create API soc_fill_sgx_param() and use it in sgx.c
- Implement same API for skylake/kabylake
- define sgx_param structure
Also include intelblocks/sgx.h instead of soc/msr.h
Change-Id: I358f0817bec5dd6cd147a645675b5688969a04e0
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There's no reason to mutate the struct device when determining
the ACPI name for a device. Adjust the function pointer
signature and the respective implementations to use const
struct device.
Change-Id: If5e1f4de36a53646616581b01f47c4e86822c42e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The original purpose of adjust_cpu_apic_entry() was to set
up an APIC map. That map was effectively only used for mapping
*default* APIC id to CPU number in the SMM handler. The normal
AP startup path didn't need this mapping because it was whoever
won the race got the next cpu number. Instead of statically
calculating (and wrong) just initialize the default APIC id
map when the APs come online. Once the APs are online the SMM
handler is loaded and the mapping is utilized.
Change-Id: Idff3b8cfc17aef0729d3193b4499116a013b7930
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch implements soc function to get previous sleep state
using chipset_power_state global structure.
acpi_get_sleep_type is needed in PRE_RAM stage when soc selects
CONFIG_EARLY_EBDA_INIT kconfig option.
Change-Id: I79acbfc09c8d255fbf9d73e49e8c7764f3f3fac6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch fixes klocwork bug due to recent memmap.c
implementation where “Pointer 'dev' returned from call
to function 'dev_find_slot' at line 144 may be NULL.”
Change-Id: I4c74ca410d1a0ba48634ec9928a0d9d1cc20e27a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This changelist adds the capture format to be set for max98927. The
nhlt blob is the same but the format params for capture are different
from the render.
BUG=b:36724448
TEST=IV feedback data is of good quality
Change-Id: I135cf4479e89cd2046ff46027f94c0f71aed650e
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Move ADD_VBT_DATA_FILE to "Devices" menu and rename it to
INTEL_GMA_ADD_VBT_DATA_FILE.
Depend on Intel platforms to avoid confusing users of non-Intel platforms.
The Intel GMA driver will use the vbt.bin, if present, to fill the
ACPI OpRegion.
Change-Id: I688bac339c32e9c856642a0f4bd5929beef06409
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch uses system agent common library to
know tseg region start and size. Unable to remove smm_region()
function from soc code as SMM common library
is not yet available for skylake use.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve successfully.
Change-Id: If98b65805753db2c30d6fea29e401a17cef39799
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to avoid build bot hang issue due to no
active default value for UART_FOR_CONSOLE kconfig
option.
Change-Id: I70ca5dc6c4bde6a119ad59d8c58955c96c042198
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21287
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures skylake device using FSP1.1 can use HW based
DRAM top calculation which was broken due to skylake fsp1.1 not
honoring any UPD to know PRMMR size and default reserving 1MB for PRMRR size.
This WA is not needed for FSP2.0 implementation due to
PrmrrSize UPD is available and considering into hw based dram top
calculation.
BRANCH=none
BUG=b:63974384
TEST=Build and boot lars which is using skylake 1.1 fsp.
Change-Id: Iade0d2cb2a290fc4c9f0e6b1eaadc8afff2fa581
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This patch to ensures that coreboot is performing SPI
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence SPI lock down programming has been moved
right after pci resource allocation is donei, so that
SPI registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure SPIBAR+HSFSTS(0x04) register FLOCKDN bit and WRSDIS
bit is set. Also, Bits 8-12 of SPIBAR+DLOCK(0x0C) register is set.
Change-Id: I8f5a952656e51d3bf365917b90d3056b46f899c5
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/21064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing DMI
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence BIOS Interface lock down through Sideband
access has been moved right after pci resource allocation is done,
so that BILD lock down is getting executed along with LPC and SPI
BIOS interface lockdown settings before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure DMI register offset 0x274c bit 0 is set.
Change-Id: Ie66701d5bd8c8f389e23fb30c8595dd83cf6b1ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing PMC
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence PMC register lock down has been moved
right after pci resource allocation is done, so that
PMC registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure PMC MMIO register 0xC4 bit 31 is set.
Change-Id: Ibd86a38fa78752ce007da63a9ccdd991ca21ab92
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing LPC
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence lpc register lock down has been moved
right after pci resource allocation is done, so that
lpc registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure LPC register 0xDC bit 1 and 7 is set.
Change-Id: I705a3a3c6ddc72ae7895419442d67b82f541edee
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to provide new config options to perform LPC and SPI
lock down either by FSP or coreboot.
Remove EISS bit programming as well.
TEST=Build and boot Eve and Poppy.
Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures that entire system memory calculation is done
based on host bridge registers.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve and poppy successfully with below configurations
1. Booting to OS with no UPD change
2. Enable ProbelessTrace UPD and boot to OS.
3. Enable PRMRR with size 1MB and boot to OS.
4. Enable PRMRR with size 32MB and boot to OS.
5. Enable PRMRR with size 2MB and unable to boot to OS due to
unsupported PRMRR size.
Change-Id: I9966cc4f2caa70b9880056193d5a5631493c3f3d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Sideband Acces locking code is skipped from FSP by setting an
FSP-S UPD called PchSbAccessUnlock. This locking is being done in
coreboot during finalize.c.
This is done because coreboot was failing to disable HECI1 device
using Sideband interface during finalize.c if FSP already locks
the Sideband access mechanism before that.
So, as a solution, coreboot passes an UPD to skip the locking
in FSP, and in finalize.c, after disabling HECI, it removes the
Sideband access.
BUG=b:63877089
BRANCH=none
TEST=Build and boot poppy to check lspci not showing Intel ME
controller in the PCI device list.
Change-Id: I8dba4c97480200507969b0f2873337f97bd2ff6a
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure core PRMRR first on all the cores and then follow
the SGX init sequence. Second microcode load would run the
MCHECK. To pass MCHECK, PRMRR on all cores needs to be
configured first. Hence, PRMRR configuration would be called
from soc_core_init while MP init for each core and then from
soc_init_cpus, BSP would call sgx_configure for each core
(including for itself). This code flow satisfies the MCHECK
passing pre-conditions; and apparently this patch fixes the
behavior of calling configure_sgx() “again” for BSP. (So
removed the TODO comment also).
Change-Id: I88f330eb9757cdc3dbfc7609729c6ceb7d58a0e1
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21007
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove passing microcode patch pointer as param while calling
- soc_core_init()
- soc_init_cpus()
Also change callbacks in apollolake/geminilake and skylake/kabylake
common code to reflect the same function signature.
Change-Id: Ib03bb4a3063d243d97b132e0dc288ef3868a5a7b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21010
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get microcode patch pointer from intel_mp_current_microcode() api
of mp_init and change sgx_configure function signature to drop
microcode_patch param.
Change-Id: I9196c30ec7ea52d7184a96b33835def197e2c799
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21009
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Skylake/Kabylake SOC has two possible ways to make serial
console functional.
1. Legacy IO based access using Port 0x3F8.
2. LPSS UART PCI based access.
This patch to provide option to select index for LPSS
UART port: 0 = LPSS UART0, 1 = LPSS UART1, 2 = LPSS UART2
PCI based LPSS UART2 is by default enabled for Chrome Design.
Change-Id: I9647820fe59b5d1a1001a611b9ae3580946da0ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of enabling power button SMI unconditionally, add a boot state
handler to enable power button SMI just before jumping to
payload. This ensures that:
1. We do not respond to power button SMI until we know that coreboot
is done.
2. On resume, there is no need to enable power button SMI. This avoids
any power button presses during resume path from triggering a
shutdown.
BUG=b:64811381
Change-Id: Icc52dc0103555602c23e09660bc38bb4bfddbc11
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We do not need or use the Management Engine MBP HOB so that
step can be skipped when FSP initializes the ME.
BUG=b:64479422
TEST=boot with FSP debug enabled binary and ensure that the
output indicates this step is being skipped:
Skipping MBP data due to SkipMbpHob set!
Change-Id: I5ea22ec4b8b47fa17b1cf2bf562337bfaad5ec0d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/20951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Need to perform a dummy read in order to activate LPSS UART's
16550 8-bit compatibility mode.
TEST=Able to get serial log in both 32 bit and 8 bit mode through
LPSS UART2 based on CONFIG_DRIVERS_UART_8250MEM_32 and
CONFIG_DRIVERS_UART_8250MEM selection.
Change-Id: I5f23fef4522743efd49167afb04d56032e16e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Add a new variable to GNVS to store information during S3 suspend
whether UART debug port controller is enabled.
2. On resume, read stored GNVS variable to decide if UART debug port
controller needs to be initialized.
3. Provide helpers functions required by intel/common UART driver for
enabling controller on S3 resume.
BUG=b:64030366
TEST=Verified behavior with different combinations:
1. Serial console enabled in coreboot: No change in behavior.
2. Serial console enabled only in kernel: coreboot initializes debug
controller on S3 resume.
3. Serial console not enabled in coreboot and kernel: coreboot skips
initialization of debug controller on S3 resume.
Change-Id: Iad1cc974bc396ecd55b05ebb6591eec6cedfa16c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20886
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Create a new function uart_lpss_init which takes the UART LPSS
controller out of reset and initializes and enables clock.
2. Instead of passing in m/n clock divider values as parameters to
uart_common_init, introduce Kconfig variables so that uart_lpss_init
can use the values directly without having to query the SoC.
BUG=b:64030366
TEST=Verified that UART still works on APL and KBL boards.
Change-Id: I74d01b0037d8c38fe6480c38ff2283d76097282a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In _FSL ACPI notification 0x83 was incorrectly being sent to DPTF.
When there should be no notification on fan speed change.
Change-Id: I66efa7a7feb911a458829a54dbd0afefabd42394
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/20875
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Internal PME is detected when bit PME_B0_STS is set. Following devices
causes internal PME.
- Integrated LAN
- HD Audio/Audio DSP
- SATA
- XHCI ('USB3')
- ME Maskable Host Wake
In SPT, PCIEXPWAK_STS bit isn't getting set due to known bug.
So scan all PCIe RP for PME status bit & update event log accordingly.
BUG=b:36992859
TEST=Build for Soraka, Verify resume due to PME on root port is logged
in elog.
Change-Id: I879a7c332e62ab598942b29d31bad84619b35ea7
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If IGD PCI device is disabled:
1. BAR for the device will be 0.
2. There is no need to allocate framebuffer for this device.
Some early SOCs don't have GFX model fuse by default hence
we need to add a check to ensure PCI device is enable. This
code to avoid die inside coreboot for missing resources.
Change-Id: Ic31d3e57ba730f6b569bf2cc3bdc54cb369b8caf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As per discussion with CSME team, ME is NOT using PCI Config
Space register HFSTS2 Bit 10 to update ME power-gated status.
ME goes to CM0-PG state after ME device becomes idle after
Bit 2 of MMIO register offset 0x800 (D0i3 Control - HECI1_D0I3C)
is being set.
And to retrieve the PG status of ME, one should read from the
PWRMBASE+offset 0x590 (which should give the value 0xF9) and
PWRMBASE+offset 0x594 (which should give the value 0xFF).
But, also it needs some time for the ME FW to go to idle state
and reflect these values in PWRMBASE registers after D0i3 bit
is being set. This does not happen instantly.
So, in coreboot, if we read the ME PG state in finalize.c, which
happens just after FSP Notify phase, where actually ME D0i3 bit
is set, we do not read the correct PG state values (i.e, 0xF9
and 0xFF).
But, once it boots to Kernel, if we read those same registers
through iotool mmio_read32 command, we get correct values.
So, removing the ME PG state prints from coreboot, since it is
actually showing wrong information, although ME Power Gating is
successful.
Change-Id: Idd31a9803b4c9db7d4bb8bbec5374583a8df0c41
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
init_igd_opregion itself is supposed to return cb_err so this adds
error handling, just like other implentations of write_acpi_tables do it.
this had been found by coverity:
*** CID 1378270: Error handling issues (CHECKED_RETURN)
/src/soc/intel/skylake/igd.c: 147 in write_acpi_igd_opregion()
141 /* If IGD is disabled, exit here */
142 if (pci_read_config16(device, PCI_VENDOR_ID) == 0xFFFF)
143 return current;
144
145 printk(BIOS_DEBUG, "ACPI: * IGD OpRegion\n");
146 opregion = (igd_opregion_t *)current;
CID 1378270: Error handling issues (CHECKED_RETURN)
Calling "init_igd_opregion" without checking return value
(as is done elsewhere 5 out of 6 times).
147 init_igd_opregion(opregion);
148 update_igd_opregion(opregion);
149 current += sizeof(igd_opregion_t);
150 current = acpi_align_current(current);
TEST=Built
Change-Id: If6f5d53037f093607d89cfe8faf193d55de7f6c4
Found-by: Coverity (CID 1378270: Error handling issues (CHECKED_RETURN))
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/20766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
The values were verified to be correct with the KabylakeFsp0001 from
github. Skylake FSP documentation disagrees so YMMV.
Change-Id: I1ee04dbbed48d5376dbc24ae70753b059f2646eb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20765
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
coreboot was setting SPI FPR register to protect the
mrc_cache data range stored in flash. This programming was being done
after FSP Notify 1.
But, FSP was locking the SPI by setting FLOCKDN Bit during Notify
phase 1, due to which coreboot was unable to protect that range.
As solution, FSP introduced a new UPD SpiFlashCfgLockDown to skip
the lockdown of flash on interest of bootloader. Set that UPD to 0
to skip the lockdown of FAST_SPI flash from FSP.
The same is being done from coreboot after end of Post at finalize.c
file.
BUG=b:63049493
BRANCH=none
TEST=FPR can be set properly to protect the mrc_cache range. The
issue reported in the bug doesn't come when both software and
hardware WP is enabled with this patch.
Change-Id: I3ffca2f1b05ab2e4ef631275ef7c3a6e23e393aa
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable SOC_INTEL_COMMON_GFX_OPREGION for all FSP versions.
Allows to get rid of opregion.c, as it's no longer needed.
Change-Id: I39190488e12917a09dbf7ee3947a33940ebc290b
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This patch is to provide an additional read LPC pci offset register
BIOS_CONTROL (BC) - offset 0xDC to ensure that the last write is
successful.
Change-Id: I308c0622d348fc96c410a04ab4081bb6af98e874
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
`CONFIG_PRE_GRAPHICS_DELAY` was only applied on a dead code path in
`igd.c` that is guarded by always selected `CONFIG_ADD_VBT_DATA_FILE`.
Nobody missed it for nearly a year, plus, it's not applied on the GOP
path, let's drop it.
Change-Id: I0b70cce3a3f2b50cb4e72c4d927b35510ff362a2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This quirk was superseded a view lines above. Also the whole path is
guarded by `CONFIG_ADD_VBT_DATA_FILE` which is always selected for
nearly a year now.
Change-Id: I7fc5184d6e81e4588616e0302dee410e74bdab5a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
It looks like this code was written with completely different semantics
in mind. Controllers, channels and DIMMs are all presented in their phy-
sical order (i.e. gaps are not closed). So we have to look at the whole
structure and not only the first n respective entries.
Change-Id: I8a9039f73f1befdd09c1fc8e17cd3f6e08e0cd47
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20650
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We've just decided to remove the only known use of the VBSD_SW_WP flag
in vboot (https://chromium-review.googlesource.com/c/575389), since it
was unused and never reliable on all platforms anyway. Therefore, we can
now also remove the coreboot infrastructure that supported it. It
doesn't really hurt anyone, but removing it saves a small bit of effort
for future platforms.
Change-Id: I6706eba2761a73482e03f3bf46343cf1d84f154b
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/20628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
HECI2 and HECI3 devices are “function disable” during FSP
Silicon Init phase. Device will not be visible over PCI bus
hence removing these devices from wake source list.
Change-Id: I0de665e039d74e49e5a22db9714bc9fee734e681
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It should never be globally exposed. Remove the global symbol
and make it static.
Change-Id: I3b85f3bbf6a73d480cdefdcdec26e137e3a3f75f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The FSP 2.0 path uses postcar to decompress ramstage. Since postcar
is entirely RAM based there's no need to have an excessively large
stack for the lzma decompression buffer. Therefore, reduce the stack
required to 1 KiB like apollolake.
Change-Id: I45e5c283f8ae87e701c94d6a123463dddde3f221
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit 5535cead (intel/skylake: Disable SaGv in
recovery mode).
Commit 5535cead disables SaGv in recovery mode to save few seconds
booting time as we were doing memory training on every recovery flow.
Now we don't need to perform MRC training on every recovery boot
due to RECOVERY_MRC_CACHE implementation in place. Hence we don't
need to define different SaGv policy between Normal (developer) mode
and recovery mode to save few seconds.
Using different SaGv parameters between recovery and all other mode
has some significent drawbacks over warm reboot cycle. We are seeing
a MRC traning hang in eve/soraka/poppy devices with below use case.
Step 1: Boot system in developer mode (first time RW_MRC training)
Step 2: Set recovery_request=1 (using crossystem) and issue “reboot”
from OS
Step 3: System will perform recovery mode MRC training and boot to
OS (first time RECOVERY_MRC training)
Step 4: Issue “reboot” from OS console.
Step 5: System wil boot in developer mode (using RW_MRC cache)
Step 6: Set recovery_request=1 (using crossystem) and issue “reboot”
from OS
Step 7: System will pick RECOVERY_MRC_CACHE and will hang during
MRC training.
This patch fixes issue mentioned above and ensures system boot to
OS without any hang if we change mode (dev<->recovery) over warm
reset.
BUG=b:63515071
BRANCH=none
TEST=manual stress testing of dev<->recovery mode over warm boot.
No MRC hang with this fix on eve/soraka/poppy devices.
Change-Id: I8d094a8b6d78ea3bf8f929870a4a179495c29c78
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Don't need this additional 2ms delay as PCR read after sideband write
help to fix original hard hang issue.
This reverts commit d4b6ac19b0.
Change-Id: I4232cba5b92e17f728795f7c282af6161e385e9b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BIOS must ensure to read same PCR offset after PCR write operation
is done.
BUG=b:35587084
BRANCH=eve
TEST=manual stress testing of D0<->D3 transition on eve failing
unit. No hard hang with this fix.
Change-Id: Id3d567aab517b16ff99a526fc29c2d71bf4042d0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The PMC of PCH-H requires a different destination id.
TEST=Run on kontron/bsl6 and observed that PM registers are correctly
dumped at start of romstage.
Change-Id: I862e4df986f1cdea34f8fa45d016fb6b51f29122
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move the generic I/O decode range setup before the console init.
TEST=Run on kontron/bsl6 which requires 0xa80/0xa81 decoded to
initialize serial ports. Serial console works from boot-
block on.
Change-Id: I9829f188c80eb73f6cd91b0c22e1c07da5745ad6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
CONFIG_SOC_INTEL_COMMON_BLOCK_SGX controls building. The SGX feature
is still enabled from devicetree.cb. As of now this SGX init supports
only KBL (SKL not tested). Support of SGX for new SOCs would be added
incrementally in this common code base.
Change-Id: I0fbba364b7342e686a2287ea1a910ef9a4eed595
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/20173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch basically does two things -
1) Remove unnecessary setting of flex_ratio to TDP nominal:
Factory configured (default) Max Non-TURBO ratio(P1) is already cofigured
in MSR_PLATFORM_INFO(0xCE).
If this Maximum Non-TURBO Ratio(P1) needs to be modified, it should be done
using MSR_FLEX_RATIO (0x194).
Here, in this code, the FLEX_RATIO is being modified by the TDP Nominal
Ratio, reading the MSR_CONFIG_TDP_NOMINAL(0x648). But this value is
actually less than the factory configured Maximum Non TURBO Ratio (P1).
So, this code is actually not required.
Also, the Bit 12 in PCH Soft Strap Register is already set in descriptor.
This Bit implies Processor Boot Max Frequency -
0 = Disable Boot Max Frequency
1 = Enable Boot Max Frequency (Default)
This setting determines if the processor will operate at maximum frequency
at power-on and boot.
Thus this patch will avoid one extra platform warm reset now onwards.
2) Remove wrongly setting Max Frequency in Bootblock phase:
In the function set_max_frequency(), the P-State max ratio was set to
TDP Nominal ratio if C-TDP was enabled, else it was set to Max Non
Trbo ratio.
But, when the cpu gets reset, it will operate with the Max-Non Turbo
ratio only, which is greater than the TDP Nominal ratio.
So, no need to set back the ratio to TDP Nominal which is lower than
the currently operating frequency.
BUG=none
BRANCH=none
TEST=Build and boot poppy
Change-Id: I24bfc86ddf0f038d85da938e41e950382fe2a6c3
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There is no choice, if not leaving it with the default the build
will fail.
Change-Id: Id91e3ce87f8ced3001fcd2125f8f6781b270f5bc
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Return CB_SUCCESS and CB_ERR instead of some integer.
Preparation to merge intel/soc and intel/nb opregion implementations.
Change-Id: Ib99fcfe347b98736979fc82ab3de48bfc6fc7dcd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In the D0 and D3 ACPI methods use word access to the PME status and
control register. This brings the code inline with the Intel reference
code and matches how the kernel handles access to this register.
BUG=b:35587084
BRANCH=eve
TEST=manual stress testing of D0<>D3 transition across multiple devices
Change-Id: I53f7465d6ad5da1780a5641ff52056445ebaca8b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For the skylake/kabylake generation of PCH there is an ACPI workaround
for emmc/sd power state that involves disabling and re-enabling dynamic
clock gating after enabling power to the controller, before setting the
power state to D0.
Under certain conditions we have observed that the controller is not
powered and ready by the time the kernel attempts to read the PME
control and status register and so the system will hang while attempting
to read PCI config register 0x84.
To ensure that the controller is ready add a 2ms delay after re-enabling
dynamic clock gating and before setting the power state to D0.
This issue has been observed on eMMC, but the same workaround exists for
the SD card interface so the same delay is added there.
BUG=b:35587084
BRANCH=eve
TEST=manual stress testing of D0<>D3 transition across many devices
shows no hard hang after 2 days.
Change-Id: If0f0323cf5437c54c907c332937b5de9dda2d8f6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
As per latest BWG, ucode reloading should be done at the end
of Mp Init, i.e., after PRMRR and other features are enabled.
No reloading specifically after SMM Relocation is required.
As, in the Common CPU MP Init code, we are already doing a
uCode load at the end of MP Init Feature Programming, hence,
the uCode loading after SMM relocation can be removed.
Change-Id: Ib1957c5fe5a8c83bb20b978a9841670b0c3e8846
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
USB port status register can be used to decide if a particular port
was responsible for generating PME# resulting in device wake:
1. CSC bit is set and port is capable of waking on connect/disconnect
2. PLC bit is set and port is in resume state
BUG=b:37088992
TEST=Verified with wake on USB2.0 port 3, mosys shows:
19 | 2017-06-08 15:43:30 | Wake Source | PME - XHCI (USB 2.0 port) | 3
Change-Id: Ie4fa87393d8f096c4b3dca5f7a97f194cb065468
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There are many good reasons why we may want to run some sort of generic
callback before we're executing a reset. Unfortunateley, that is really
hard right now: code that wants to reset simply calls the hard_reset()
function (or one of its ill-differentiated cousins) which is directly
implemented by a myriad of different mainboards, northbridges, SoCs,
etc. More recent x86 SoCs have tried to solve the problem in their own
little corner of soc/intel/common, but it's really something that would
benefit all of coreboot.
This patch expands the concept onto all boards: hard_reset() and friends
get implemented in a generic location where they can run hooks before
calling the platform-specific implementation that is now called
do_hard_reset(). The existing Intel reset_prepare() gets generalized as
soc_reset_prepare() (and other hooks for arch, mainboard, etc. can now
easily be added later if necessary). We will also use this central point
to ensure all platforms flush their cache before reset, which is
generally useful for all cases where we're trying to persist information
in RAM across reboots (like the new persistent CBMEM console does).
Also remove cpu_reset() completely since it's not used anywhere and
doesn't seem very useful compared to the others.
Change-Id: I41b89ce4a923102f0748922496e1dd9bce8a610f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19789
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FIT is already loading microcode before CPU Reset. So, we need
not update the microcode again in RO FW in bootblock.
But we need to update in RW FW if there is any new ucode version.
So, added the update microcode function in get_microcode_info callback
before MP Init to make sure BSP is using the microcode from cbfs.
BUG=none
BRANCH=none
TEST=Build and Boot poppy
Change-Id: I5606563726c00974f00285acfa435cadc90a085e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20051
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
If the boot media is memory mapped temporarily mark it as write
protect MTRR type so that memory-mapped accesses are faster.
Depthcharge payload loading was sped up by 75ms using this.
Change-Id: Ice217561bb01a43ba520ce51e03d81979f317343
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch perform resource mapping for PCI,
fixed MMIO, DRAM and IMR's based on inputs given by SoC.
TEST=Ensure PCI root bridge 0:0:0 memory resource allocation
remains same between previous implementation and current
implementation.
Change-Id: I93567a79b2d12dd5d6363957e55ce2cb86ff83a7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/19796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add ACPI method GPLD to generate port location data when
passed visiblity info. Will be used by _PLD method in
board-specific USB .asl files.
Change-Id: I14ba3cea821e103208426e9fcaa0833d84157ff8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The word 'coreboot' should always be written in lowercase, even at the
start of a sentence.
Change-Id: I7945ddb988262e7483da4e623cedf972380e65a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Place `tdp_pl2_override` above the FSP options as it's not an FSP option.
Change-Id: Idff2b628d19ce1a80294b28c55c05ba4157d07e0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Provide some enums instead of unreadable comments that are usually
copied all over.
Change-Id: Iff551565647f28ecb226e1df633b4deec0ab0a7f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add config for cpu base clock frequency(Mhz) and replace current
refrence from soc/cpu.h with config option.
Change-Id: Idf8e85f7ae6d965fa987a4f5c4905503ee354d69
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/20016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently, there is no macro to set GPIO interrupt trigger mode.
The purpose is to make coreboot set same trigger mode as GpioInt
BUG=b:62067569
TEST=checked unused interrupt on SD_CD does not happen after s3 resume
Change-Id: I42b9cd80b494e24c55b97e54cdf59bfd24dd9054
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/19992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add more fine-grained details about what device caused the PME wake
event. This requires checking the PME status bit (bit 15) in PCI PM
control and status register for the PCI device.
BUG=b:37088992
TEST=Verifed that XHCI wake source was identified correctly:
135 | 2017-05-25 15:28:17 | ACPI Enter | S3
136 | 2017-05-25 15:28:26 | ACPI Wake | S3
137 | 2017-05-25 15:28:26 | Wake Source | PME - XHCI | 0
Change-Id: I6fc6284cd04db311f1f86b8a86d0bb708392e5d5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19925
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement GPIO ACPI AML generating functions that can be called by
coreboot drivers to generate GPIO manipulation code in AML. Following
API functions are implemented:
1. acpigen_soc_read_rx_gpio
2. acpigen_soc_get_tx_gpio
3. acpigen_soc_set_tx_gpio
4. acpigen_soc_clear_tx_gpio
In addition to the API functions above, helper functions are added to
gpio.asl to set/clear/get Tx value of GPIO.
BUG=b:62028489
Change-Id: I77e5d0decd8929a922d06b02312378f092551667
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19828
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Field Programmable Fuses (FPF) status maintained by
CSME in bits 30:31 of FWSTS6 for Skylake and Kabylake.
FPF committed means CSME has blown the fuses.
Change-Id: If63c7874e6c894749df8100426faca0ad432384b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/19747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
If deep Sx is enabled and prev sleep state was not S0, then if SUS
power was lost, it means that the platform had entered deep Sx. Add an
elog entry for deep Sx variant in this case.
BUG=b:38436041
TEST=Verified that elog entries are updated correctly:
Deep S5:
59 | 2017-05-19 10:39:08 | Kernel Event | Clean Shutdown
60 | 2017-05-19 10:39:09 | ACPI Enter | S5
61 | 2017-05-19 10:39:17 | System boot | 22
62 | 2017-05-19 10:39:17 | EC Event | Power Button
63 | 2017-05-19 10:39:17 | ACPI Deep Sx Wake | S5
64 | 2017-05-19 10:39:17 | Wake Source | Power Button | 0
65 | 2017-05-19 10:39:17 | Chrome OS Developer Mode
Deep S3:
66 | 2017-05-19 10:40:11 | ACPI Enter | S3
67 | 2017-05-19 10:40:16 | EC Event | Power Button
68 | 2017-05-19 10:40:16 | ACPI Deep Sx Wake | S3
69 | 2017-05-19 10:40:16 | Wake Source | Power Button | 0
Normal S3:
77 | 2017-05-19 10:43:22 | ACPI Enter | S3
78 | 2017-05-19 10:43:39 | EC Event | Power Button
79 | 2017-05-19 10:43:39 | ACPI Wake | S3
80 | 2017-05-19 10:43:39 | Wake Source | Power Button | 0
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
