These functions are no longer used and may be removed:
* vboot_handoff_check_recovery_flag
* vboot_get_handoff_flag
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ie05652ef1288eef74bd2e7e8bea79fd29d523859
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33533
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two functions retrieve vboot recovery_reason:
* vboot_handoff_get_recovery_reason
* vboot_get_recovery_reason_shared_data
Previously, when CBMEM comes online, a vboot_handoff data
structure is created, and depending on the architecture,
coreboot may eventually lose access to vboot_working_data.
After implementing vboot_working_data CBMEM migration,
vboot_working_data is always guaranteed to be accessible.
vboot_get_recovery_reason_shared_data is corrected to also
allow accessing vboot_working_data in ramstage and postcar.
Now, vboot_handoff_get_recovery reason returning a valid recovery
reason implies that vboot_get_recovery_reason_shared_data should
*also* return a valid recovery reason. Thus we may remove the
former.
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Iac216dc968dd155d9d4f8bd0f2dfd5034762f9a0
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The default voltage of vsim2 is set to 2.76V for sim card usage.
In general, 2.76V of vsim2 is composed of 2.7V main voltage and 0.06V calibration voltage.
However, vsim2 is used for the tx_ovdd power of display port IT6505 on the kukui board design which needs 2.7V.
So we set it to 2.7V with modifying calibration value.
BUG=b:126139364
BRANCH=none
TEST=measure vsim2 voltage with multimeter
Change-Id: I4dffdde89cbde91286d92e6c2b445f0b3d0ad2fe
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Intel Braswell supports i2c block writes using SMBus controller.
This support is missing in actual smbus routines.
Add do_i2c_block_write() which is a based on do_smbus_block_write() but
also write first byte to SMBHSTDAT1.
The caller needs to configure the SMBus controller in i2c mode.
In i2c mode SMBus controller will send the next sequence:
SMBXINTADD, SMBHSTDAT1, SMBBLKDAT .. SMBBLKDAT
To ensure the the command is send over the bus the SMBHSTCMD register must
be written also
BUG=N/A
TEST=Config eDP for LCD display on Facebook FBG-1701
Change-Id: I40f8c0f5257a62398189f36892b8159052481693
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Hatch newer board revision do not use USB port5 for discrete BT.
Hence remove the port configuration and UBS2 P5 asl entry. The older
board version would continue to use USB2 P5 hence moved the entry to
overridetree.cb
Change-Id: I98297d6b81e3184b7b0a14710f3790f5df30d68b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch configures FSP UPD values for HPD and DDC of DDI ports for
WHLRVP.
BUG=none
TEST=Tested that eDP & DP works on WHLRVP
Signed-off-by: Usha P <usha.p@intel.com>
Signed-off-by: sridhar <sridhar.siricilla@intel.com>
Change-Id: I576469f5564e3e56159762752dbe4557e9dc1912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33435
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LONG_FADT is not used at all. So remove it and use sizeof(acpi_fadt_t) for
header length.
Change-Id: I433d1b2e0f3b9505d7c52eb14f1a476fbe52a284
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The clock was previously set to 52MHz to workaround the fact that
depthcharge didn't support tuning.
Tuning has now been enabled in depthcharge:
https://chromium-review.googlesource.com/c/chromiumos/platform/depthcharge/+/1655553
BUG=b:122244718
TEST=Verified on grunt that it speeds up boot by 130ms
Change-Id: If847cea2a7848bcd175958db86e652d4f710201a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This commit follows up on commit commit 89989cf6 with Change-Id:
I1f44ffeb54955ed660162a791c6281f292b1116a ("src: Drop unused include
<arch/acpi.h>").
Change-Id: I3dc12373b32b95d25ba7b302cbca5f927678315d
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33365
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit follows up on commit 8b7a1614 with Change-Id:
I73c557d6ef009fb2cac35fdea500dee76f525330 ("src/mainboard: Remove
unneeded include <arch/io.h>").
Change-Id: I7f307bf5b6cdcfebe1a290ce344b962fcecc8781
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Change the SMBIOS Version from 2.7 to 2.8. Necessary changes were
already pushed in https://review.coreboot.org/c/coreboot/+/33031
Change-Id: I237cdee7d43e814397b958e4cf941bf58949088d
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Print I2C SAR device info so that it is available in cbmem logs.
BUG=none
BRANCH=none
TEST=Boot up and check cbmem -c can find the SAR I2C info
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia143932bb660ed2c2cea76310f11ede2b727adf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33432
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
data &= !BIT0 will clear data, since !BIT0 evaluates to 0 (oops). We
only want to clear bit 0, not the whole thing, so use bitwise negation
instead.
Change-Id: I2179119e0d2d4aceaf4f8b499bf4c5baf4ef677f
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1241812
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This was done to update the global variable g_ichspi_lock but this is
now removed in favor of reading the lock bit during runtime instead of
keeping track of the state.
Change-Id: I8cb69a152b0e050d64d8979ee92de2d24136f8dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33390
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SPI swseq controller can be locked in other parts of the code, for
instance when it's locked down in the finalize section. The driver
has to be made aware of that. The simpler solution is to not keep
track of the state and simply read out the lock bit on each SPI
transfer.
Change-Id: Ifcd5121b89d6f80fc1c1368786982d0d9fa1bf61
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We had a value that was overloaded thrice.
By moving them in a common structure and ordering them by value such
issues are hopefully avoided in the future.
Also add a few values to libpayload that were only defined in
commonlib.
Change-Id: I227d078eebee2d92488454707d4dab8ecc24a4d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32958
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Set abort command define
* Set debug level to SPEW
* Support zero length data packet in ipmi_kcs_send_message
That's required for commands like GET_DEVICE_ID, which have no
additional data to send.
* Read reply even if given no receive buffer
* Prevent buffer overflow in read reply processing
Tested on Wedge100s.
Change-Id: Iefddd88a744c3b96751d3fe8c2951ca2115548ce
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33488
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The temperature delta between on-board thermistor and
surface temp change, so update DPTF parameter accordingly.
BUG=b:113101335
TEST=Tested in thermal chamber by thermal team.
See comment 148 / 153 in the bug.
Change-Id: Ie18be94fc1e7476755fb0e6947cce559854a82dd
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
The sandybridge systemagent-r6 blob is modified:
- To be more flexible about the location of the stack w.r.t. the heap
- Place the MRC pool right below the MRC_VAR region
- to work with the same DCACHE_RAM_BASE from the native raminit (could
make the CAR linker symbols easily compatible if desired)
This allows CAR setup compatibility between mrc.bin and native
bootpath and also allows for BIOS/memory mappeds region larger than
8MB.
This changes the semantics of CONFIG_DACHE_RAM_MRC_VAR_SIZE to also
include the pool on top of MRC_VAR region.
TESTED on T520 (boots and resumes from S3 with mrc.bin).
Change-Id: I17d240656575b69a24718d90e4f2d2b7339d05a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33228
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix 'do not use assignment in if condition'.
Change-Id: I6e1b81a1b87de4315391618968c59cc3d3a66a77
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Move the memory strap gpios to variant/gpio.h, as the memory straps
are different for helios.
Change-Id: I1833c9539687011ee27fd3e88c0581e30ca59354
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
All usage of pci_read_config8 was removed in commit d44d4f0f with
Change-Id Ia959eb5b747846048396e66d4c926c96c27f3878 ("mb/lenovo/*:
Remove useless smihandler code"). So we don't need this include anymore.
Change-Id: Ic4f038c80e17799016ae7e92a5675cfe7c71e400
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This patch ensures to boot platform without onboard GFX (PCI B0:D2:F0)
enabled from mainboard devicetree.cb.
TEST=Previously platform was dying at "GMADR is not programmed!" with
IGD disabled.
Change-Id: I8c907ee25db4538a84890f2ccc3187afa86604b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33449
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Selecting which cbfs prefix to load is only implemented with the romcc
bootblock.
Change-Id: I09523b94605f00ab15b5f0ea3986ac08e3a6afc6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
"if (_pcidata != 0xFFFFFFFF || _pcidata != 0)", is always true.
The right test should be && not ||.
Error found using -Wlogical-op warning option.
Change-Id: I537fa4867499e1e6e5f662086fabc99b91aa0c70
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
These if statements can be combined to merge the two branches of the
conditional and remove the duplicate pDCTstat->Speed == 3 check.
Change-Id: I41aa19b4b7ed7b1a0e4f83f72e66869760e677dd
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229583
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Helios has a number of GPIO changes w/r/t to its baseboard.
Override early, sleep and normal GPIOs as appropriate.
BUG=b:135257452
BRANCH=none
TEST=Compile only (no boards to test with)
Change-Id: I45793ad6515df5af5b925d92106bd943374353d4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change tcc offset from 0 to 10 degree celsius for bloog.
BUG=b:135225497
BRANCH=octopus
TEST=Build and verify test result by thermal team.
Change-Id: I4cbff846914a776c67692005f8b40cd73cfaf231
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Memory id's are 1-indexed for DDR4, so we need to check that the SPD
index is non-zero before converting it to the 0-indexed value in the
bitmap.
Change-Id: Icc542239d91c39b89c23f31856c28e7c20b2fc4d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1387028
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Rather than force the user to create the RW_MRC_CACHE FMAP region,
simply select CACHE_MRC_SETTINGS so it's done automatically for them.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: Iaa1da6015c1bfafe8ea81ca34ef8851f0c689487
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The gpio_key wakeup_event_action in the ACPI tables was backwards, causing
devices to wake up on pen insertion instead of removal. Changed to
EV_ACT_DEASSERTED.
BUG=b:134547896
BRANCH=none
TEST=Verified in OS, device only wakes up on pen removal
Change-Id: I0816ed9fb23cf00fd8e40bcdd25ff7a9f48badbd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33427
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change the SPD makefile to use the LPDDR3 SPDs. Set up the arrays
for mapping SoC DQS pins to LPDDR3 pins.
BRANCH=none
BUG=b:133455595
TEST=`FEATURES="noclean" FW_NAME="helios" emerge-hatch chromeos-ec
depthcharge vboot_reference libpayload coreboot-private-files
intel-cmlfsp coreboot-private-files-hatch coreboot chromeos-bootimage`
Ensure the firmware builds without error.
Change-Id: Iebaba2ec65dfcf36674b4733b421ada107b22b09
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33456
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We are seeing an EC interrupt after setting the EC RAM offset that
indicates that the EC should transition to S0ix mode and this is
preventing the kernel from going into S0ix on the first try.
As a workaround if we read back from the EC RAM while still in the
_DSM handler it seems to prevent this problem.
BUG=b:130644677
BRANCH=sarien
TEST=ensure s0ix entry works on the first try with sarien
Change-Id: Id607c4c2b14b79d0cd1bcea0c2032be2f2c0c141
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33455
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These 4 GPIOs are being disconnected in the next board so use the
board ID to configure these pins as not connected to ensure
they do not cause leakage.
Also remove the ACPI _PTS S5 code that was configuring the GPIOs.
This does mean they will cause small leakage in S5 on existing boards,
but it will not affect the new boards.
BUG=b:132393441
TEST=boot on sarien with fake board ID and ensure that coreboot
configures these pads as expected.
Change-Id: I6ac04b9a635829811a09aeab7cba3bb58cfcff47
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
These two functions try to access arrays of lengths 32 and 64 at indices
of at most 259 and 71 (respectively). Something here is seriously wrong.
This code was introduced in 2007, and aside from cosmetic changes, has
had no modifications since then. I don't know what this code is supposed
to do, and asking around on IRC, no one else did either. Until someone
has the interest and time to work on it, let's at least add a die() to
prevent the out of bounds access and alert the user that something is
wrong.
Change-Id: I5fc15a50a9f0e97add31e3a40da82a15f7427358
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 12296{79-82}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch is not actually disabling HECI1 as it requires a dedicated FSP UPD
for WHL/CML SoC code to set this HECI1 chip config.
Change-Id: Ia88f3315a9dc3365d0acc13ed887e7c596c97c91
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch provides an additional option to skip HECI function
disabling using SMM mode for WHL and CML platform, where FSP has
dedicated UPD to make HECI function disable.
User to select HECI_DISABLE_USING_SMM if FSP doesn't provided dedicated
UPD.
Right now CNL and ICL platform will use HECI_DISABLE_USING_SMM kconfig
to make HECI disable and WHL/CML has to rely on FSP to make HECI
disable.
Change-Id: If3b064f3c32877235916f966a01beb525156d188
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
As per Icelake EDS PCI device B:D:F (0:0x1f:0) referred as ESPI,
hence modify SoC code to reflect the same.
This patch replaces all SoC specific PCI LPC references with ESPI
except anything that touches intel common code block.
Change-Id: I4990ea6d9b7b4c0eac2b3eea559f5469f086e827
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
No C_ENVIRONMENT_BOOTBLOCK support for Braswell is available.
Enable support and add required files for the Braswell Bootblock in C.
The next changes are made support C_ENVIRONMENT_BOOTBLOCK:
- Add car_stage_entry() function bootblock-c_entry() functions.
- Specify config DCACHE_BSP_STACK_SIZE and C_ENV_BOOTBLOCK_SIZE.
- Add bootblock_c_entry().
- Move init from car_soc_XXX_console_init() to bootblock_soc_XXX_Init()
Removed the unused cache_as_ram_main() and weak car_XXX_XXX_console_init()
BUG=NA
TEST=Booting Embedded Linux on Facebook FBG-1701
Building Google Banos
Change-Id: Iab48ad72f1514c93f20d70db5ef4fd8fa2383e8c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Recovery path should finalize work context, and trim
vboot_working_data buffer_size. Otherwise, depthcharge ingests
the full 12 KB workbuf in recovery path.
BUG=chromium:972528, b:134893812
TEST=Build with vboot_reference CL:1584488. Check that USB disks
are properly verified in recovery path.
BRANCH=none
Change-Id: Icf2600d2eb5d846a26aec35a153946dd2f7f128c
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable dynamic clock gating for the community cr50's IRQ lives on.
That IRQ is pulsed very quickly, and with clock gating enabled pulses
tend to be missed. This is expecially true on the default 0.0.22
firmware that cr50 comes with out of the factory.
BUG=b:130764684 b:130338605
BRANCH=None
TEST=Boot hatch with cr50 "intap" firmware that can vary the pulse width,
observe that even with sub-microsecond pulses no IRQs are missed.
Change-Id: I34d14fb7cc97e33eecfda2c99cc53a541c87662d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It was determined through testing that 16MB of reserved VRAM is
sufficient. Additional RAM for the graphics driver is allocated out
of system memory.
BUG=b:123579702
TEST=Boot Grunt, watch VRAM usage with graphics driver logging.
Change-Id: I44b640f015b45c0dc3d701929549f3a1082a9268
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33368
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The prototype of vprintk() is currently declared unconditionally, which
prevents it from being used in situations where the console is disabled.
The code will compile correctly, but not link, since the definition in
console.c isn't being provided. This adds a shim around the declaration
so that, like printk(), a call to vprintk() in this situation will expand
to a no-op function instead.
Change-Id: Ib4a9aa96a5b9dbb9b937ff45854bf6a407938b37
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
die() currently only accepts a fixed message string, which is rather
inconvenient when there is extra information that would be helpful to
print in the error message. This currently requires an extra call to
printk(), which is somewhat awkward:
printk(BIOS_EMERG, "Bad table, opcode %d at %d", id, i);
die(""); // what do I say here?
die() already has a printk() inside it to print the error message, so
let's just make it variadic to combine the two.
die("Bad table, opcode %d at %d", id, i); // much better
Forwarding variadic arguments from one function to another is rather
tricky, so die_with_post_code() is redefined as a variadic macro
instead.
Change-Id: I28b9eac32899a1aa89e086e0d3889b75459581aa
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Keith Short <keithshort@chromium.org>
This patch removes all possible dependencies in order to build platform
with CONFIG_RAMPAYLOAD enable(without ramstage).
A. Create coreboot separate stage kconfigs
This patch creates seperate stage configs as below
1. HAVE_BOOTBLOCK
2. HAVE_VERSTAGE
3. HAVE_ROMSTAGE
4. HAVE_POSTCAR
5. HAVE_RAMSTAGE
B. Also ensures below kconfigs are aligned with correct stage configs
1. COMPRESS_RAMSTAGE and RELOCATABLE_RAMSTAGE are now enable if
CONFIG_HAVE_RAMSTAGE is selected.
2. COMPRESS_BOOTBLOCK will enable if CONFIG_HAVE_BOOTBLOCK is set
3. COMPRESS_PRERAM_STAGES will enable if CONFIG_HAVE_VERSTAGE
|| CONFIG_HAVE_ROMSTAGE is selected.
C. Also fix compilation issue with !CONFIG_HAVE_RAMSTAGE
On x86 platform:
Case 1: ramstage do exist: CONFIG_HAVE_RAMSTAGE=1
>> rmodules_$(ARCH-ramstage-y) will evaluate as rmodules_x86_32
Case 2: ramstage doesn't exist: CONFIG_HAVE_RAMSTAGE=0
>> rmodules_$(ARCH-ramstage-y) will evaluate as rmodules_
This patch fixes Case 2 usecase where platform doesn't select
CONFIG_HAVE_RAMSTAGE.
Also add option to create sipi_vector.manual based on $(TARGET_STAGE)
variable.
$(TARGET_STAGE)=ramstage if user selects CONFIG_HAVE_RAMSTAGE
$(TARGET_STAGE)=postcar if user selects CONFIG_RAMPAYLOAD
Change-Id: I0f7e4174619016c5a54c28bedd52699df417a5b7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a method for the soc/amd/<product> to indicate what AcpiMmio
ranges are supported. Induce a build error if soc or mainboard
code is added which attempts to use an unsupported block.
This patch attempts to dissuade accessing unsupported blocks without
requiring the complexity of structures or reinitializing at the
beginning of a new stage.
TEST=boot grunt, force build errors by removing blocks in iomap.h
BUG=b:131682806
Change-Id: I2121df108fd3caf07e5588bc3201bcdd8dcaaa00
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
This patch adds support for the Dual SPI feature (SDR 2-bit in Qualcomm
terminology) to the QSPI controller.
Change-Id: I7aed2ccd9627f5de5dd760b418f74d56d2c031d3
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33284
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support to read SPI flash in Dual SPI mode, where both
MISO and MOSI lines are used for output mode (specifically Fast Read
Dual Output (0x3b) where the command is still sent normally, not Fast
Read Dual I/O (0xbb) whose additional benefit should be extremely
marginal for our use cases but which would be more complicated to
implement). This feature needs to be supported by both the flash chip
and the controller, so we add a new dual_spi flag (and a new flags field
to hold it) to the spi_flash structure and a new optional xfer_dual()
function pointer to the spi_ctrlr structure. When both are provided,
Dual SPI mode is used automatically, otherwise things work as before.
This patch only adds the dual_spi flag exemplary to all Winbond and
Gigadevice chips, other vendors need to be added as needed.
Change-Id: Ic6808224c99af32b6c5c43054135c8f4c03c1feb
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
All SPI flash chip drivers currently in coreboot use the generic read
functions (spi_flash_cmd_read_fast()/_slow()) as their read callback.
The only use case for specialized read callbacks we have left is with
specialized flash controllers like Intel fast_spi (which sort of
impersonate the flash chip driver by implementing their own probe
function).
This patch unifies the behavior for all normal flash drivers by making
the read callback optional and letting them all fall back to a default
read implementation that handles normal fast/slow reading. Most of the
drivers used to install the respective callback after checking
CONFIG_SPI_FLASH_NO_FAST_READ, but some hardcoded either slow or fast
writes. I have found no indications for why this is and spot-checked
datasheets for affected vendors to make sure they all support both
commands, so I assume this is just some old inaccuracy rather than
important differences that need preserving. (Please yell if you
disagree.)
Also take the opportunity to refactor some of the common spi_flash.c
code a bit because I felt there are too many nested functions that don't
really do enough on their own, and centralizing stuff a bit should make
it easier to follow the code flow. (Some of this is in preparation for
the next patch.)
Change-Id: I2096a3ce619767b41b1b0c0c2b8e95b2bd90a419
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch changes the Gigadevice SPI flash driver to adopt the same
structure packing improvements for the hardcoded parameters of
individual chips that was implemented for Winbond last year. This cuts
the size of the hardcoded info nearly in half and should save us a few
hundred bytes in every stage.
Change-Id: I9910dcb9b649f51b317f3f8fcba49e5e893f67d2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SPI transfer speed logging in cbfs_spi is super useful, doesn't get
in the way (just adding one line per stage, essentially) and should have
no notable overhead. Let's enable it by default for the BIOS_DEBUG log
level rather than having to recompile to get it.
Also fix an issue with building this code on MIPS due to lack of 64-bit
division primitives. (This means MIPS and arm32 board may display
incorrect results when reading more than 4MB in a single transfer, which
sounds very unlikely.)
Change-Id: I03c77938afe01fdcecf917e8c4c25cc29cdc764e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for generating IndexField, which is similar to Field.
Change-Id: If66a627e64953696b0b68488256bd5c141e4c205
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33032
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
One variant is asking for support for 16G 2666 LPDDR3, so adding
generic SPD for that.
BUG=b:133455595
BRANCH=None
TEST=None as this is not being used yet
Change-Id: If16a101119aabc30d6ea83e95e9ded2e089a982d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
One variant is asking for support for 8G 3200 DDR4, so adding generic
SPD for that.
BUG=b:132920013
BRANCH=None
TEST=None as this is not being used yet
Change-Id: I89cd3287aaf0baf384c4fe82d0881b0c48e09753
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33258
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Skip GT specific programming in coreboot to support early
parts without GT enable.
Change-Id: I231e13367cbfbafbfb0cb4235487dbcbcae76820
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33189
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RAMPAYLOAD symbol added by 7e893a02c0 (Kconfig: Create RAMPAYLOAD
kconfig) is shown unconditionally for all x86 systems. It generally
creates a lot of confusion to prompt for something that isn't imple-
mented or not working. So guard it with another Kconfig that can be
selected by platforms that actually support it.
Change-Id: I6d158382d1000b8b40ca1368e2efff0c39884f15
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33263
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Select ONBOARD_VGA_IS_PRIMARY in driver/lenovo/hybrid_graphics to fix
disabling iGPU in 'Dual Graphics' on Lenovo T430.
* Remove ONBOARD_VGA_IS_PRIMARY in mainboards that already select
DRIVERS_LENOVO_HYBRID_GRAPHICS.
Change-Id: I6594fbb957c9a8135fe670d38b5755adf29d2dff
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Move the contents of iommu.c to early_init.c.
* Name the functions like done in intel/soc/common.
* Move PAMx register setup to own function
Preparations for integration in soc/intel/common/*
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I3ec395bf6722bceb84316e92733dcfcd7a093639
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32068
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the Return statement within the PS0, PS3 methods. PS0/3 are not
allowed to return anything. Even an empty return will be resolved to
Return(Null). In order to be conform with the specification, the code
has been refactored to remove the return statements.
Change-Id: I7b4820e8dd40a9169a7facce67282b8af5af67af
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33293
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add Skylake C236 to the PCH Table. The one which was already in there is
actually the CM236 and not the C236. This can be checked in datasheet:
100-series-chipset-datasheet-vol-1 p. 25.
Change-Id: I435927f15e9d3219886375426b09c68632dfe3d9
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change adds support for the UCSI specification in order to
provide information about the Type-C port and an interface to
perform power and data role swap.
This change is split across the DSDT and SSDT, with the shared
memory and operation region declared in the SSDT after being
allocated in CBMEM.
The OS will fill in the registers in the system memory region and
then call the _DSM method wtih a read or write argument. The DSM
method will copy the required registers to/from the system memory
and the EC and perform the write or read action.
Responses from the EC will generate a new SCI with event code 0x79
which will notify this UCSI ACPI device and the OS driver will take
action to read status from the EC.
BUG=b:131083691
Change-Id: I438a2bdfaf6720acd8354e0339dcef2844b63a4e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The USB Type-C Connector System Software Interface (UCSI) defines a
required memory oregion for the OS UCSI driver to use to communicate
with the BIOS and EC.
This provides a CBMEM ID that can be used by drivers to allocate this
shared memory region for the UCSI driver to use.
BUG=b:131083691
Change-Id: Id5b7fa19436443bc11a6ebe3ce89cd552cee4d85
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SD controller seems to take some time after restarting
the clock at 1.8V before it actually switches from 3.3V to
1.8V. Add a _DSM method that simply sleeps when switching
between 3.3V and 1.8V. Otherwise, the kernel times out too
quickly waiting for the card to acknowledge the 1.8V switch.
The card itself is waiting until it sees the clk signal being
driven at 1.8V.
BUG=b:125441242
TEST=Boot Hatch with SD card and CR2 removed, observe voltage
switch succeeds.
Change-Id: I15090ed9f9bc90b35dfcba47c913e3d37b799d0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signef-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These are documented in the Intel Datasheet entitled
"6th Generation Intel® Processor Datasheet for S-Platforms"
"6th Generation Intel® Processor Datasheet for H-Platforms" (Volume 2)
Without them, coreboot fails to properly inform the payload of the
amount of available memory.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Change-Id: I5b810c6415c4aa0404e5fa318d2c8db292566b8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The values are generated from the respective VBTs.
Change-Id: Ic74e9dac898c17ce64a94b06682997a39daeff69
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30247
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Logs from Linux' i915 suggest that not even the FSP/GOP takes proper
care of this. The sequence is mostly the same as on older platforms,
with a slightly different configuration of the backlight PWM.
We light the panel up with 50% PWM duty cycle. This often results in
an already rather high perceived brightness, but shouldn't be too
blinding.
Change-Id: I762a77c8df023a4c14af502af5edfeeb961da1ae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Modify the 16 and 32 bit BIOS RAM access functions that had been
originally moved from stoneyridge. This was suggested in the
review of
69486cac7: Create AcpiMmio functionality from stoneyridge
Change-Id: I5b491da6f263cbab2b549301e16a7e19896f2428
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32932
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Document the AcpiMmio individual blocks better. This is in response
to a request in gerrit for
69486cac7: Create AcpiMmio functionality from stoneyridge
Correct comments that were inadvertently left in place from older
patches.
Change-Id: I4c16a866de5622e8cfbd3a08816b9d3182950d0e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32931
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable VBOOT MIGRATE_WORKING_DATA so that the data
required by depthcharge is copied into the coreboot tables
and made available to depthcharge after BOOT_IMEM is cleansed.
Change-Id: I0317b73d24b07553672695998589f86677e0be64
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add PRESERVE flag to preserve the VPD data.
Change-Id: I78ab4de31030465345c5ae58813bfed5e27494fb
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33020
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change all arguments named "offset" to "reg" to match the others.
These should have gone into change
69486cac7: Create AcpiMmio functionality from stoneyridge
Change-Id: Ifdd00d0a5d1e03bfa68a13eeece2d2cfd56aa39d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32930
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reorder the biosram prototypes to match the rest of the file. Remove
prototypes for asf 32-bit functions that have not been implemented.
Change-Id: Ic2663158d8a71952c26eb37f34342a6ea5e58a42
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32929
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Relocate the alink access functions out of stoneyridge where they
were dead code. This source maintains the ability to access all
register spaces, however more modern APUs define only ABCFG in
the BKDGs.
BUG=b:131682806
Change-Id: I5c558ccc64bd04a66399c678d43beb0a97e72f63
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32663
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the address and replace the hardcoded value in the ASL code.
Change-Id: If0b99de78d8c5948e2e5f2aa50dfc2efc1bd1ba1
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32662
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Separate chipset-specific source from sata_init(), and modify it
to better match coreboot conventions. A subsequent patch will
move the generic portion to soc/amd/common.
The support for enabling port multipliers appears to have been
first added for Kabini. Although missing from the documentation,
the ability to affect the HBA Capabilities Register seems to remain
for Stoney Ridge.
Change-Id: I5dd9f613d36badc3e4d185a22b4475cb82ce187e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32660
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Obsolete pm_acpi_pm_cnt_blk(), and remove it and pm_acpi_pm_evt_blk().
Relocate the remaining functions to get/save UMA information to
southbridge.c.
Change-Id: I90c4394e3cf26f4ad60a078948a84303bda693d0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32659
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the function into common code. Convert it to use the memory-
mapped access type. Convert vboot_platform_is_resuming() to call it
instead of duplicating the source.
BUG=b:131682806
Change-Id: I245bebb8dc2d331cdd56acfb245a004536b792ab
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32658
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The AcpiMmio block allowing direct access to the ACPI registers
has remained consistent across AMD models. Move the support from
soc//stoneyridge to soc//common.
BUG=b:131682806
Change-Id: I0e017a71f8efb4b614986cb327de398644599853
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32655
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The halt.c file relies on the ACPI register block in the AcpiMmio
range. This register block is consistent across AMD device
generations, so to prepare for moving additional stoneyridge support
to this directory by changing the file name and add a Kconfig symbol
to control the build.
BUG=b:131682806
Change-Id: I2f7442dd78bced7f69b0416a8cd751291f82151f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32654
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AMD devices traditionally have the LPC-ISA bus at 14.3 and the
definition has been very consistent. Relocate the feature from
stoneyridge into common/block.
BUG=b:131682806
Change-Id: I8d7175b8642bb17533bb2287b3e3ee3d52e85a75
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32653
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A subsequent patch will move the soc//stoneyridge LPC functionality to
a common directory. Prepare by reworking the SPI BAR configuration
function in southbridge.h. The SPI BAR is not a typical PCI BAR, and
is at D14F3xA0.
Change-Id: I73ddb4afaf9e67ca0522ecb6085b23c92fedc461
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32652
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The banked GPIO functionality in the AcpiMmio block has been consistent
since the Mullins product. Move the basic support into a common
directory.
Each product's pin availability, MUXes, and other details must remain
specific to the product.
The relocated source also drops the weak configure_gevent_smi() that
reports SMI is not available. The stoneyridge port relies on SMI
to do its initialization, similar to modern soc/intel devices. This
is the plan for future soc/amd ports, so make a missing function a
build error instead of a runtime warning.
BUG=b:131682806
Change-Id: I9cda00210a74de2bd1308ad43e2b867d24a67845
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch makes smm related files compile independent of
ramstage getting compiled.
If user selects RAMPAYLOAD to boot without ramstage, there
will be need for smm code to get compiled independently.
Change-Id: I17a3eb80a4d5ef86e0319357c01b6bf5b90ef15b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33115
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows to port C_ENVIRONMENT_BOOTBLOCK to sandybridge separately
from nehalem.
Change-Id: If3c6619cf22d1e2995eb19823b0f3f969d252b3b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
* Add initial board commit based on HP8200 SFF.
* Add documentation.
* Serial and PCIe slot are working.
Tested on HP Z220.
Change-Id: I75987a7ea9a008a64281f0d5ab27e5148d36a4ec
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33207
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ECC Support and VDD Voltage to dimm_info struct. Now Bus Width
and ECCSupport will be propagated correctly in SMBIOS Type 17 Entry.
Change-Id: Ic6f0d4b223f1490ec7aa71a6105603635b514021
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33031
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because of some differences to the baseboard this board variant needs
its own GPIO table.
Change-Id: Ie3424cb0b867c5d43cd7db9e9ae654196cef5e90
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This automatically detects whether the southbridge supports AHCI.
If AHCI support is selected it will be used unless "sata_no_ahci" is
set in the devicetree to override the behavior.
Change-Id: I8d9f4e63ae8b2862c422938f3103c44e761bcda4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The RW_LEGACY section needs to be minimum 1M. For the 16MB BIOS
region, we had this region set too small, which was causing the
firmware_FMap FAFT test to fail.
BUG=b:133857135, b:129464811
BRANCH=None
TEST=test_that -b hatch <IP> firmware_FMap
Change-Id: Ie6311613ca3bb08e7f058a41d12f9a1153dc9c5e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Initial support for Facebook FBG-1701 system.
coreboot implementation based on Intel Strago mainboard.
Configure 'Onboard memory manufacturer' which must match HW.
BUG=N/A
TEST=booting SeaBIOS and Linux 4.15+ kernel on Facebook FBG-1701
Change-Id: I28ac78a630ee705b1e546031f024bfe7f952ab39
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
hexdump() is not available in postcar stage.
Add hexdump() functionality to postcar stage.
BUG=NA
TEST=Booting Embedded Linux on Facebook FBG-1701
Change-Id: Ibdce911065c01b0a1aa81dc248557257d0e420b0
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Coverity detects pointer fih as FORWARD_NULL. Add sanity check
for fih to prevent NULL pointer dereference.
BUG=CID 1401717
TEST=Built and boot up to kernel.
Change-Id: Ia6853e5302c87d9ffe52b942f067be56f6e77406
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Clang Static Analyzer version 8.0.0 detects null pointer argument
in call to memory copy function. Add sanity check for pointer header
to prevent null pointer dereference.
TEST=Built and boot up to kernel.
Change-Id: I7027b7cae3009a5481048bfa0536a6cbd9bef683
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Some variants only support 4 PCIe ports so there is no need to have
those unavailable ports in the devicetree.
Change-Id: I154cae358fb7f862fc0c8eaa620474b37b5e6484
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30821
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:133389422
TEST=check SSD's power off sequence to meet PCIE requirement.
SSD's reset should be cleared before clearing SSD's power EN Pin.
Change-Id: Ia106b805deafb8a442b56bcce91b51135cb32988
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33182
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We keep its definition in libpayload, though, to maintain compatibility
with existing payload code. For now.
Change-Id: I8fc0d0136ba2316ef393c5c17f2b3ac3a9c6328d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The code in cpu/intel/car/romstage.c Does most of the things like
setting up timestamps, stack guards, entering postcar.
A functional difference is that the FSP header is searched for twice
instead of passed from the CAR entry to the C code. When using
C_ENVIRONMENT_BOOTBLOCK this needs to be done anyway (or a special
linker symbol kept across multiple stages is needed, which is likely
not worth the speedup).
Change-Id: I0f03e5a808f00157fdd807b104417a54e4bde7b2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
FDT property data should not be const -- sometimes we need to update it,
for example when fixing up phandles in an overlay. On the other hand
it's occasionally desirable to put a string constant in there without
having to strdup() it all the time... let's just live with the tiny
implicit assumption that the data we'd want to modify (phandle
references, mostly) will never be added from string constants, and put a
cast in dt_add_string_prop().
Change-Id: Ifac103fcff0520cc427ab9a2aa141c65e12507ac
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32868
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the device tree dumping functions (not compiled by
default but available for debugging) to output properties and nodes in a
format similar to .dts files that is very close to what dtc outputs when
you decompile a .dtb with it. This makes it easier to match device tree
dumps from coreboot with device tree dumps generated by other device
tree tooling.
This patch was adapted from depthcharge's http://crosreview.com/1536386
Change-Id: Ib40e50d906aff05473a70c4fc9b124d63232558c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32867
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support to lookup nodes via the "/aliases" mechanism in
device trees. This may be required for overlay support (don't quite
remember tbh) and is also just a generally useful feature. It was
adapted from depthcharge's http://crosreview.com/1249703 and
http://crosreview.com/1542702.
Change-Id: I1289ab2f02c4877a2d0111040384827e2b48a34a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32866
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently DT paths are *not* expected to start with '/'. This is not
what the spec says (see Devicetree Specification v0.2, 2.2.3 Path Names)
and also not what is done by Linux.
Change dt_find_node_by_path() to expect paths to start with '/' and add
a leading '/' to all DT path strings. Besides the compatibility with the
spec this change is also needed to support aliases in the future.
This patch was adapted from depthcharge's http://crosreview.com/1252770
Change-Id: Ibdf59ccbb4ead38c6193b630642fd1f1e847dd89
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32865
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Besides looking up a node with an absolute path dt_find_node_by_path()
currently also supports finding a sub-node of a non-root node. All
callers of the function pass the root node though, so it seems there
is no real need for this functionality. Also it is planned to support
DT path names with aliases, which would become messy in combination with
the lookup from a sub-node.
Change the interface of dt_find_node_by_path() to receive the DT tree
object instead of a parent node and adapt all callers accordingly.
This patch was adapted from depthcharge's http://crosreview.com/1252769
Change-Id: Iff56be4da2461ae73a7301dcaa315758d2a8c999
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32864
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
