Tune I2C bus 1 clock and insure it meets I2C spec.
BUG=b:142683257
TEST==flash coreboot to the DUT and measure I2C bus 1 clock
frequency less than 400KHz
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Id4cdbad4dd9d451763fb536988402d6e6fe3a378
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update power sequence to meet spec.
BUG=b:142710867
TEST=touchscreen work, and make sure power sequence to meet
spec with vendor.
Change-Id: I98f8b095374caa8c3540307a51f9d3b69baec905
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36060
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the SPD data for MT40A1G16KD-062E:E
BUG=b:139397313
TEST=Compile successfully.
Change-Id: I3d1ae9269ff3129845a7f53dbacbab6e1b66b6d5
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This sets up some common default LPC decode ranges in a common place.
This may set up more decode ranges than needed but that typically does
not hurt. Mainboards needing additional ranges can do so in the
mainboard pch_enable_lpc hook.
Change-Id: Ifeb5a862e56f415aa847d0118a33a31537ab8037
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Port the backlight-PWM handling from Skylake instead of the previously
used Haswell version. We use a 200Hz PWM signal for all boards. Which
is higher than the previous devicetree value, 183Hz, but that was over-
ridden by the VBIOS anyway. 200Hz is still very low, considering LED
backlights, but accurate values are unknown at this time.
Lynx Point, the PCH for Haswell and Broadwell, is a transition point
for the backlight-PWM config. On platforms with a PCH, we have:
o Before Lynx Point:
The CPU has no PWM pin and sends the PWM duty-cycle setting
to the PCH. The PCH can choose to ignore that and use its own
setting (BLM_PCH_OVERRIDE_ENABLE).
We use the CPU setting on these platforms.
o Lynx Point + Haswell:
The CPU has an additional PWM pin but can be set up to send
its setting to the PCH as before. The PCH can still choose
to ignore that.
We use the CPU setting with Haswell.
o Lynx Point + Broadwell:
The CPU can't send its setting to the PCH anymore. BLM_PCH_
OVERRIDE_ENABLE must always be set(!) if the PCH PWM pin is
used (it virtually always is).
We have to use the PCH setting in this case.
o After Lynx Point:
Same as with Broadwell, only BLM_PCH_OVERRIDE_ENABLE is
implied and the bit not implemented anymore.
Change-Id: I1d61d9b3f1802ebe18799fc4d06f1f1d3b54c924
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On some configuration coreboot boots too fast and the EC reports the
max temperature, resulting in Linux shutting down immediately.
Change-Id: I610c7c9fbf2130566d3c2c758f1796314d3a0973
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Enable wifi sar feature and set wifi sar name for dragonair sku.
BUG=b:142109545
TEST=emerge-hatch coreboot chromeos-bootimage
1. Check wifi_sar-dragonair.hex in /cbfs-rw-raw/dratini
2. Add iwlwifi.debug into kernel params.
3. check SAR value from dmesg only when sku id is 21/22
Change-Id: I0e08610b7c7d2d8da5a749d278bcde26af590e31
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
On Hyper-Threading enabled platforms the MSR_PRMRR_PHYS_MASK was written
when already locked by the sibling thread. In addition it loads microcode
updates on all threads.
To prevent such race conditions only call the code on one thread, such
that the MSRs are only written once per core and the microcode is only
loaded once for each core.
Also add comments that describe the scope of the MSR that is being
written to and mention the Intel documents used for reference.
Fixes crash in SGX MP init.
Tested on Supermicro X11SSH-TF.
Change-Id: I7102da028a449c60ca700b3f9ccda9017aa6d6b5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35312
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The port is based on the x201 / t410s.
2537-vg5 / i5, no discrete gpu
Tested and working:
* Native raminit
* Native gfxinit
* Booting Seabios 1.12.1
* Booting from EHCI
* Running GNU/Linux 5.0.0
* No errors in dmesg
* EHCI debug on the devices left side, bottom-right
* Keyboard
* Fn keys (Mute, Volume, Mic)
* Touchpad
* TPM
* Wifi
* Sound
* USB
* Ethernet
* S3 resume
* VBOOT
Testing in progress.
Untested:
* VGA
* Displayport
* Docking station
Bugs:
* AC adapter can't be read from ACPI
* TPM not working with VBOOT and C_ENV BB
Details for flashing externally:
1. Disconnect all power
2. Connect the external flasher
3. Connect the power cord (This fixes internal power control)
4. Remove the power cord
Change-Id: Id9d872e643dd242e925bfb46d18076e6ad100995
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/11791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This does the following:
- Add gen[1-4]_dec options to the devicetree to set up generic LPC
decode ranges in the southbridge code.
- Move setting up some default decode ranges to a common place. If
somehow a board needs to override this behavior it can happen in the
mb_setup_superio() hook (that will be renamed when moving to
C_ENVIRONMENT_BOOTBLOCK).
Change-Id: I3d904b1125bc410c11aa73a89b1969284e88dac1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
A few notable changes:
- Microcode init is done in assembly during the CAR init.
- The DCACHE_BSP_STACK_SIZE is set to 0x2000, which is the same size
against which the romstage stack guards protected.
- The romstage mainboard_lpc_init() hook is removed in favor of the
existing bootblock_mainboard_early_init().
Change-Id: Iccd7ceaa35db49e170bfb901bbff1c1a11223c63
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The NO_POST option covers more than classical port 80 output, hence
selecting it seems wrong in any case. The default is still rather
user patronizing, but let's keep it.
As a side effect, this fixes the ability to override the default
for NO_POST which Kconfig rejected while these boards selected it.
(Seems like a bug in Kconfig, though.)
Change-Id: I896b08812b1aa6ce249d7acc8073ebcc0f72eace
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Some boards with the G41 chipset lacked programming CIR, so this
change add that to those boards too.
Change-Id: Ia10c050785170fc743f7aef918f4849dbdd6840e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
The vendorcode/eltan mboot and verified boot options only build if a
few other Kconfig options are defined.
Change-Id: Ie333d2fbf294e23ec01df06ee551e2d09541c744
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35954
Reviewed-by: Wim Vervoorn
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The next board rev will have a new option for an Elan touchscreen. Add
support for this in the devicetree, as well as use the 'probed' property
on both touchscreen options.
BUG=b:141957731
BRANCH=none
TEST=compiles (next board rev not available yet)
Change-Id: I135e693304cbb8dffc0caf4c07846033d6802208
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Update GPIO_138 and GPIO_139 setting to fix EMR function.
BUG=b:141729962,b:141281846
BRANCH=octopus
TEST=verify EMR function in Grob360S.
Change-Id: I28cef592374fb4aeee2f3d3010cc0e237d62a2fd
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Load the calibration params from flash first and check the correctness
of the params. If the params have correct format, perform DRAM fast
calibration with these params to reduce bootup time. Otherwise, load the
DRAM blob and perform DRAM full calibration.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I8de29b14b1fb24b3b4f351c855c5c4d8f350cc34
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Load calibration params from flash. If the format of the params is
correct, use these calibration params for fast calibration to reduce the
bootup time.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I9ef4265dd369a1c276bb02294696556df927e7bc
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35164
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FreeBSD's sh (basic posix shell) did not interpret the '\%o' escape
in the same way bash/zsh do. As a result, the decoded files ended up
with ASCII numbers instead of the decoded binary data.
Change-Id: I95b414d959e5cd4479fcf100adcf390562032c68
Signed-off-by: Greg V <greg@unrelenting.technology>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Minimize use of hard-coded value for acpi_table_header->length to soft
code. Replace length of acpi_header_t with sizeof(acpi_fadt_t).
Change-Id: Ibcae72e8f02497719fcd3f180838557e8e9abd38
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The superio driver that was linked in is nct6779d but static
devicetree expected symbol superio_nuvoton_nct5572d_ops.
Change-Id: I648b7680bb39b9ff5b38cc3bd5147bd336e0b282
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Applying reset_gpio config of stylus for kohaku. GPP_A19 has been assigned in
the latest schematics.
We would keep GPP_A10 as output high for old revision devices temporarily.
BUG=b:141914474
BRANCH=none
TEST=verified stylus works internally
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I61f0f9a4378f47bf455f0726d44beeaf2f67197b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Add PRESERVE to UNIFIED_MRC_CACHE so that we don't retain the memory
training data upon a FW update unless we need to. We have had users
complaining that a 15 second memory training upon update makes them
believe that their device is not booting, thus many of them hard
resetting before bootup.
BUG=b:142084637
BRANCH=None
TEST=flash RW_SECTION_A, RW_SECTION_B, and WP_RO sections and make
sure memory training doesn't occur on following bootup.
Change-Id: Ia5eb228b1f665a8371982544723dab3dfc40d401
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35803
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change does the following:
- Move PCH init code from the common romstage to sb code, this allows
for easier reuse in bootblock
- Provide a common minimal LPC io decode setup, mainboards can
override this in the mainboard_lpc_init if required
- Set up LPC generic IO decode up in romstage based on devicetree
settings
- Remove the ramstage LPC generic IO decode from ramstage as this is
now done in romstage.c
- Get rid of unneeded setup of spi_read configuration in BIOS_CNTL as
this is already done in the bootblock.
Change-Id: I3f448ad1fdc445c4c1fedbc8497e1025af111412
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move the mainboard_romstage_entry to a common location and provide
mainboard specific callbacks.
Change-Id: Ia827053617cead5d2cf8e9f06cb68c2cbb668ca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is based on the sandybridge settings.
The current lookup table comes from the x201 vendor lookup table.
Tested: USB mouse and webcam still work and current registers are the
same as before. USB IR are not but the code follows EDS instead of the
register replay.
Change-Id: Icea9673623a62e7039d5700100a2ee238478abd1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35762
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The values read back in those ranges are identical before and after
this change and the Lenovo Thinkpad X201 still boots fine.
Change-Id: I406510e0573ac97003da7d97181abdfbfd2a872f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35760
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RCBA registers 0x3400-0x3500 are all handled elsewhere
in the code, so no need to have a 'replay' of those.
The remainder now consist of USB setup and undocumented bits
that should likely not be touched at all.
Change-Id: I69fc8a5e16f7cf0e1068d0d2ed678a6c2f6e70a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This does the following:
- implement a PCH disable function that will be called by the PCI
drivers as part of their chip_ops
- removes the iobp_x calls as those don't exist on ibexpeak
- complete the devicetree with to be disabled PCI devices for the
chip_ops to be called
- Clean up some code copied from bd82x6x
Change-Id: I78d25ffe9af482c77d397a9fdb4f0127e40baddc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This properly sets up the chipset initialization registers, instead of
replaying an RCBA dump.
The information is taken from the EDS and from the thinkpad x201
vendor BIOS disassembly and from an HP UEFI.
TESTED on Thinkpad X201. Seems stable at booting, rebooting and resume
from S3.
Change-Id: I21c2beaf70da27dbe6a56e2612df2c257c05fc62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The extra PCI bus RST# and 200ms delay there was workaround
for custom add-on hardware.
Change-Id: I38c4677cfb41d620498be8e0c257b517995bad5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Minimize use of hard-coded value for acpi_table_header->revision to soft
code. Replace with macro defined in arch/acpi.h for FADT and with the
get_acpi_table_revision function for SSDT.
Change-Id: I99e59afc1a87203499d2da6dedaedfa643ca7eac
Signed-off-by: Sourabh Kashyap <Sourabhka@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ONBOARD_MICRON_MEM and ONBOARD_SAMSUNG_MEM are available.
These are used to determine if Samsung or Micron onboard memory is
assembled. This can not detected run-time.
Choice is replaced by one config.
Only oldest HW revision contains Samsung module, so set
CONFIG_ONBOARD_SAMSUNG memory to default No.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: Id65e92bd4b8d4fe3a6b87dec9bf77e3a62e1be96
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
No support is available in mainboard.
Add support to mainboard:
- Add mb_log_list[]
- Add routine mb_crtm()
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: I5120ffb6af0b41520056e1773f63b7b2f34a2460
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The vendorcode for verified boot is uploaded, but not used by a mainboard.
Add support to the mainboard for verified boot.
The items to be verifed are placed in board_verified_boot.c
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701 rev 0-2
Change-Id: I3ea0a95287977df0dea13e05acedd5406538a6ee
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33463
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously all boards using eSPI for the Chrome EC just called it
LPC as the code for the chrome EC is the same between the two
busses.
I'm adding a new Kconfig symbol to specify eSPI, so switch the
boards that actually use eSPI to that symbol and add the LPC
symbol to all the others.
The EC_GOOGLE_CHROMEEC_LPC symbol will no longer default
to enabled for x86 platforms, so one symbol or the other needs to be
specified for each platform.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Icf242ca2b7d8b1470feda4e44b47a2cdc20680f2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Connected 4K monitor is not configured at max resolution. The
framebuffer size is too small.
Increase the framebuffer size to 64MB. This is sufficient for max
configuration of 1 HDMI monitor combined with internal LCD panel.
BUG=N/A
TEST=4K HDMI monitor and LCD working fine on Facebook FBG-1701
Change-Id: I25d2cd696830fc5bda84ea2b87538f526373998e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
PCB version is determined using inb() in actual code.
Create function mainboard_read_pcb_version to read pcb version.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: I7c16627f468d84ca4ad2aab8bf9fb555f50dc23c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The previously provided device path made no difference, all
integrated PCI devices point back to the same chip_info
structure.
Change reduces the exposure of various SA_DEVFN_xx and
PCH_DEVFN_xx from (ugly) soc/pci_devs.h.
Change-Id: Ibf13645fdd3ef7fd3d5c8217bb24d7ede045c790
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Disable memory channel by HW strap pin. Using for factory
debug.
BUG=b:139773082
BRANCH=N/A
TEST=Rework HW strap pin and check /proc/mem_info
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic5f53f0ba3bd432fbcb7513d2a8aa49d42f7a23e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35241
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two fields of struct sdram_params are renamed for future CL of DRAM full
calibration. Field 'impedance' is also removed.
BUG=none
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I2f9673fd5ea2e62ee971f0d81bdd12aaf565e31c
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35738
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the the FSP Parameter PchHdaVcType a devicetree setting and make
use of it in the devicetrees of all boards that currently set it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ibafc3b6bd2495658f2bd634218042ec413a89f5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
A missing definition of gameport base (PNP io 0x60) will cause
an automatic address assignment during PCI/PNP enumeration, which
won't obey limit 0x7ff. This will cause the enumeration to fail
as other devices already have the values enabled.
The symptoms are: not working USB, PS/2, garbled UART console,
not working PCIe GPUs and crashes. Probably because of wrongly
assigned IO ports.
Example of log (shortened):
Done reading resources.
Setting resources...
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.0 1c * [0x0 - 0xfff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.1 1c * [0x1000 - 0x1fff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.2 1c * [0x2000 - 0x2fff] io
!! Resource didn't fit !!
aligned base 400 size 10 limit 2e7
40f needs to be <= 2e7 (limit)
PCI: 00:1f.2 20 * [0x3080 - 0x308f] io
!! Resource didn't fit !!
...
ERROR: PCI: 00:02.0 14 io size: 0x0000000008 not assigned
...
ERROR: PCI: 00:1f.2 10 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 14 io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 18 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 1c io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 20 io size: 0x0000000010 not assigned
...
PCI: 00:1b.0 subsystem <- 8086/27d8
PCI: 00:1b.0 cmd <- 102
PCI: 00:1c.0 bridge ctrl <- 0003
PCI: 00:1c.0 subsystem <- 8086/27d0
PCI: 00:1c.0 cmd <- 107
PCI: 00:1c.1 brids70c01mcu0PeC: 0
dV0i8s0immicrocode: upd10a00000y0025 x666600CPU physiaB 0 0 e k
MTRR cheaeu60zeAttemfWaiting for 1st Sot AP: slot 1 apic_L0ecl0zsax a
aInitiNntt kac:oIG0 Ua dUrSGSGL Ct0C07fintel_vga_int15_h
VGA Option ROM wa7..Azalia0Azalia: codkAbCiPCI: 00:1c.0 init finished
We can see the ports probably started to collide after the activation
of 00:1c.0 device. A debug run with compiled SPEW shows the problem
with enumeration:
PCI: 00:1f.1 18 * [0x50b8 - 0x50bf] io
PCI: 00:1f.2 10 * [0x50c0 - 0x50c7] io
PCI: 00:1f.2 18 * [0x50c8 - 0x50cf] io
PCI: 00:1f.1 14 * [0x50d0 - 0x50d3] io
PCI: 00:1f.1 1c * [0x50d4 - 0x50d7] io
PCI: 00:1f.2 14 * [0x50d8 - 0x50db] io
PCI: 00:1f.2 1c * [0x50dc - 0x50df] io
PNP: 002e.7 60 * [0x50e0 - 0x50e0] io <-- gameport base
DOMAIN: 0000 io: base: 50e1 size: 40e1 align: 12 gran: 0 limit: 7ff done
Notice a weird base for DOMAIN, along with the limit.
Adding a definition of gameport (0x220) as a workaround fixes
the problems.
The gameport should be still disabled thanks to disable bits
(W83627THF datasheet is little bit chaotic). I didn't find any info
if the gameport is available on some pads of the motherboard.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Change-Id: Ie8e42552ac5e638e91e5c290655edcce1f64e408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is a PCI standard register, no need to alias its
definitions under different names.
Change-Id: Iea6b198dd70fe1e49b5dc0824dba62628dedc69a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This also reworks the interface to override OPs from the devicetree to
match the interface in sb/intel/common/spi.
Change-Id: I534e989279d771ec4c0249af325bc3b30a661145
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
To support mt8183 power saving during suspend to RAM, this patch loads
SPM firmware to support SPM suspend. SPM needs its own firmware to do
these power saving in the right timing under correct conditions. After
linux PM suspends, SPM is able to turn off power for the last CPU and do
more power saving for the SoC such as DRAM self-refresh mode and turning
off 26M crystal.
BUG=none
BRANCH=none
TEST=suspend/resume passes for LPDDR4 3200
Change-Id: I3393a772f025b0912a5a25a63a87512454fbc86e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This removes the "ifdef ACPI" which is not needed here as we currently
don't include gpio.h in any asl file.
Change-Id: I803bbee5933eda9423a9bc9fcaea9e905e3ac78e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35543
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes the warning that power_on_after_fail could not be found,
adds a default config and adds the parameter hyper_threading.
Change-Id: I10b0aa71fa7916b01e93e16cbd81e427fd14f6a4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35526
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CONFIG_GBB_HWID can be generated automatically now so we can remove
the test-only HWIDs set in board config files.
BUG=b:140067412
TEST=Built few boards (kukui, cheza, octopus) and checked HWID:
futility gbb -g coreboot.rom
Change-Id: I4070f09d29c5601dff1587fed8c60714eb2558b7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35635
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: Iee12a5d1781c869b20bc14a52ecbf23474caa3fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cometlake pch EDS vol1 section 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on drallion platform, able to boot up into OS and stay
at power up state.
Change-Id: Idd1befeb14a251b7c0542ca1f99049d07b28fb98
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Per google/stout.
Tested with SanDisk SSD U110.
Change-Id: I7cc9837f572236acac2007e95990e64c25a5d6e2
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Based on schematic and register dumps.
Change-Id: I91fc47022988cfe986fb8c1ed21dc073ee7d16bc
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The vendor id option set here is useless as most SSVID registers get
filled with 0x8086 (their VID) by default, anyway.
Besides that the Kconfig option isn't meant for retrofit ports, cf.
commit 7e1c83e31b (Add Kconfig options to override Subsystem Vendor and
Device ID). The right place would be the devicetree.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If67c679bb342f63096902535734106e4f1651118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Most of the X11 boards with socket LGA1151 are basically the same boards
with just some minor differences like different NICs (1 GbE, 10 GbE),
number of NICs / PCIe ports etc.
There are about 20 boards that can be added, if there is a community for
testing.
To be able to add more x11 boards easily like x11ssm (see CB:35427) this
restructures the x11ssh tree to represent a "X11 LGA1151 series". There
were multiple suggestions for the structure like grouping by series
(x10, x11, x...), grouping by chipset or by cpu family.
It turned out that there are some "X11 series" boards that are
completely different. Grouping by chipset or cpu family suffers from the
same problem. This is why finally we agreed on grouping by series and
socket ("X11 LGA1151 series").
The structure uses the common baseboard scheme, while there is no "real"
baseboard we know of. By checking images, comparing logs etc. we came to
the conclusion that Supermicro does have some base layout which is only
modified a bit for the different boards.
X11SSH-TF was moved to the variants/ folder with it's gpio.h. As we
expect the other boards to have mostly the same device tree, there is a
common devicetree that gets overridden by each variant's overridetree.
Besides that some very minor modifications happened (formatting, fixing
comments, ...) but not much.
Documentation is reworked in CB:35547
Change-Id: I8dc4240ae042760a845e890b923ad40478bb8e29
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35426
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify IRQ pin from D21 to A21 and support wake-up from touchpad
BUG=b:141519690
TEST=build bios and verify elan touchpad works fine
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6cc5b780ffcee24f1f2a04e88c30628ceb5904e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35551
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
new DDR particle:
1. Samung K4A8G165WC-BCWE
2. Hynix H5AN8G6NCJR-XNC
BUG=b:139085024
BRANCH=master
TEST=rework new source to DUT and re-flash bios to DUT and
verify DUT will bring up successfully
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I0d039af53938086733308a081a77a7398e7bf5d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the configuration 'Juniper' for the new mainboard.
BUG=b:137517228
TEST=make menuconfig; select 'juniper' and build
Change-Id: I94e3ac7f6de3fecf177e344cb217eaecf6362d69
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All variants of hatch are using Comet Lake and so the selection can be
done in Kconfig without requiring each variant to do the same.
Change-Id: Ief34296334ede5ba0f5f13381e92427ccc440707
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Sort the names of all variant mainboards in an ascending order.
Change-Id: I19d502298744c0e0cbc91eb836c62ca90cdb9a5c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: I3d58094256d2730dbd249291a8f1ed8df9dfe62d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The implementation of udelay() with LAPIC timers
existed first, as we did not have calculations
implemented for TSC frequency.
Change-Id: If510bcaadee67e3a5792b3fc7389353b672712f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34200
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Razer Blade Stealth H2U is a KabyLake System using:
- Intel KBL 7500U
- ITE8528E SuperIO
- Intel 600P Series NVMe SSD
- Either four MT52L1G32D4PG (16GB) or MT52L512MB32D4PG (8GB)
of soldered memory in dualchannel mode
- (Optional) Touchscreen
- HDMI 2.0a via DP-1: Paradetech PS175
- AlpineRidge Thunderbolt 3 controller
- TPS65982 USB-PD power switch / multiplexer
Even though it has a 16MB chip equipped (W25Q128.V) only the first 8MB
are used and mapped via IFD. The rest is left empty (0xFF). The flash is
not secured in any way and can be read via flashrom. It should be the
source for this port's IFD and ME blobs.
Working:
- USB-A Ports left and right
- Speakers
- Touchscreen (USB)
- Onboard Keyboard in Linux
- NVMe SSD
- SeaBIOS, Tianocore and Grub Payloads
- Webcam
- Powersaving Modes
- Battery state and LID switch, sometimes slow to update.
- Touchpad (I2C-HID)
- Headphones
Not part of this commit:
- Thunderbolt / USB-C (Requires advanced EC signaling)
- Full HDMI support (Currently requires plugged connection at boot)
Change-Id: I7ede881d631e1863f07f5130f84bc3b8ca61a350
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Disable root port IOU0 to which built-in NIC is attached.
TEST=on OCP monolake, hide built-in NIC and make sure OS does not report
built-in NIC
Change-Id: I2384e7dd073355f0ced2902ac2d8418996b1c5aa
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
- configure DMA fw_cfg
- add support to read using fw_cfg_dma
- provide fw config version id info in logs
BUG=N/A
TEST=Build and boot using qemu-i440fx.
Change-Id: I0be5355b124af40aba62c0840790d46ed0fe80a2
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fill the dimm info struct to make SMBIOS type 17 appear.
TESTED=Up Squared
Change-Id: I4de63362c8fea8a886594cdcf0eec48421afb605
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34564
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop unused CNF2_LPC_EN, as there is no device which uses IO 0x4e/4f.
Do not use the mainboard model to set COMA_LPC_EN. Make use of
NO_UART_ON_SUPERIO instead, as it is more future-proof.
Change-Id: Iac49250b0f509a42012f82db8aa85ba85559c66f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
BUG=b:140545732
TEST=build bios and spd index set to 6, verify DUT bring up normally
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I337b0bdcd37a9c4baacccbc6786968031a41b31e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35511
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CdClock does not need to be set because the board does not use IGD.
Change-Id: I6835ccdf80530f9efc6fdeb0363dcf9267f99d21
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Implement Locator and Bank fields (as reported by dmidecode) to match
vendor BIOS.
TEST=on OCP monolake, run dmidecode tool and see that "Locator" field
matches expectation.
Change-Id: Ia271ff1e596ba469cf42e23d8390401c27670a27
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The specified CBFS_SIZE does not make sense.
The boards BIOS region is 0xb00000. Correct the value.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia3014c7fd081030607790ced6bb55323086f1161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35458
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A closer read of the EDS indicates that when GPIO Driver mode is
selected, GPIO input event updates are limited to GPI_STS only.
GPI_GPE_STS updates are therefore masked, and we don't want to enable
this behavior. It masks the GPE and does not allow us to see this GPE
as a wake source, obscuring the reason that the system woke up.
Also switch the IRQ from level-triggered to edge-triggered,
otherwise the system will auto-wake from any sleep state when the
pen is ejected from the garage.
BUG=b:132981083
BRANCH=none
TEST=Wake up system from S0ix using pen eject, verify that mosys
eventlog shows GPE#8 as the S0ix wakeup source. Wake up system from S3
via pen eject, and verify that the wakeup source shows as GPE#8.
Change-Id: If017e12e23134f5cfed7cbb6047cc9badd9bf7e8
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35459
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implementing logic base on sensor detection to determine SKU id.
BUG=b:140472369
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5e71ae6b97378b78055735bbf4b6b55ffe38b978
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35366
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initialize the input_hertz and uart_pci_addr fields of the lb_serial
struct to prevent later undefined reads in lb_add_serial(). This was
done for exynos5420 in commit ff94e00362 (soc/samsung/exynos5420/uart.c:
Init new serial struct variables), and this patch finishes the rest.
Note that not all of the drivers can have the UART PCI address
configured at build time, so a follow-up patch will be needed to correct
those ones.
Change-Id: I733bc8185e2f2d28a9823495b53d6b09dce4deb1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1354778
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34548
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add DPTF based thermal control for ambient sensor for CML based
Helios system. Also, update other sensor names information.
BUG=b:139335207
BRANCH=None
TEST=Build and Boot on Helios board and check all sensor details.
Change-Id: I322d53536fbdf6db70f5a24afb322d9f206eaeac
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update DPTF thermal temperature threshold values for CML based
Helios system. This updates CPU active cooling temperature
threshold to appropriate values which addresses the issue of
running the Fan at lower CPU temperature as per bug.
Also, added active cooling temperature thresholds for other
TSR sensors.
BUG=b:141087272
BRANCH=None
TEST=Build and boot on Helios board to check the fan functionality.
Change-Id: I5c8502f8c9e6121c18024d2a8d5a4f7680797b8d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35446
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no board named X11SSH+-TF.
Change-Id: Ide01a8d59c09747dfe7d59fd9e17bd5194fb14e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Add SKU#18 to config power sequence below:
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:134854577,b:137033609
BRANCH=octopus
TEST=build
Change-Id: I58e07518f6daaf608684c9fa1b1c88fc592ea117
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds SPD files for Drallion. Use spd_index
matrix to correspond mem_id. This can save the dummy spd index
to reduce the size of SPD.bin.
BUG=b:139397313
TEST=Compile successfully
Change-Id: I2f7e75fdbca4183bcd730e40fef4bfe280ab900b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35346
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some T430s variants have a Thunderbolt controller wired to PCIe port
The controller hotplugs itself to the chipset when a downstream device
is hotplugged into it, so the hotplug capability should be enabled on
PCIe port #5.
TODO: find the correct gpio pin to detect the Thunderbolt controller
at runtime.
There are 3 variants of mainboard for Thinkpad T430s: Basic type
(Wistron LSN-4 11263-1), Boards with an additional discreet GPU,
Boards with an additional TB controller (Wistron LSN-4 11271-1),
each of which has a different schematic.
The gpio27 on the last type is set as set as GPIO-INPUT, compared
with GPIO-OUTPUT-HIGH on the basic type boards.
Change-Id: I61f41db100f398069e50e2da8a378b3a8d1c84bf
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This Kconfig symbol is set at a default of 36 in cpu/x86 and is now
only used in the romcc bootblock to set up caching to upgrade the
microcode. It's not mainboard specific.
Change-Id: I29d3a8308025e586a823603f8d6edafd30cb9d95
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and ATF(BL31) can get this parameter.
Change-Id: Iefa70dc0714a9283a79f97d475b07ac047f5f3b0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This change overrides USB port settings for kohaku.
Some port settings are same with baseboard, but I'd like to describe all
settings here to be aware of current setting and usage of USB ports on
kohaku.
BUG=none
BRANCH=none
TEST=built and measured SI of USB ports internally
Change-Id: I5ac05485d1cd94416e5a0aecf7fa6769bd7c9e84
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Information based on superiotool dump.
Change-Id: I24ae9b1a7eab3095518341354544efe613912a6a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enables and configures GPIOs in the NCT6791D chip. The values for
registers taken from the superiotool dump.
Change-Id: I5968a6c20cc013697d64bfbe4fc2e7b2390b72b0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch uprevs the Arm Trusted Firmware submodule to the new upstream
master (commit 42cdeb930).
Arm Trusted Firmware unified a bunch of stuff related to BL31 handoff
parameters across platforms which involved changing a few names around.
This patch syncs coreboot back up with that. They also made header
changes that now allow us to directly include all the headers we need
(in a safer and cleaner way than before), so we can get rid of some
structure definitions that were duplicated. Since the version of entry
point info parameters we have been using has been deprecated in Trusted
Firmware, this patch switches to the new version 2 parameter format.
NOTE: This may or may not stop Cavium from booting with the current
pinned Trusted Firmware blob. Cavium maintainers are still evaluating
whether to fix that later or drop the platform entirely.
Tested on GOOGLE_KEVIN (rk3399).
Change-Id: I0ed32bce5585ce191736f0ff2e5a94a9d2b2cc28
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
drallion_ish.bin is updated for drallion GPIO changes
and not compatible with arcada_cml.
TEST=Build and boot arcada_cml
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Change-Id: Idb35c33425bfd50533df74349dd645db18a65bc5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Even though GT7375P programming guide rev0.4 only requires a reset delay
of 120ms, in practice, we have to increase the reset delay to 500ms, or
Goodix FW update would fail.
This is a workaround. In the long run, we hope Goodix can fix the power
sequence in touch firmware.
BUG=b:138795891, b:138796844
TEST=boot helios board and verify Goodix FW update succeeded
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Ic0049bf240de0a1c7f1b1f39bf155d48bb76fb86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35350
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will increase ME region size and reduce the BIOS region size.
BUG=b:140665483
TEST='compile successfully'
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5be2580d280569421d0870a06f9b93124b564b6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35304
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PchPwrOptEnable FSP UPD is for internal testing and not really available
in externally released FSP source hence assigning this UPD using devicetree
config dmipwroptimize doesn't do anything.
TEST=Build and boot sarien/arcada.
Change-Id: I6da2a088fb697e57d12008fa18bd1764b3da7765
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
With the current devicetree the kernel doesn't provide any serial
after serial init.
Update the devicetree to resolve this issue.
Tested on HiFive Unleashed.
Change-Id: I4427d34a12902e0eaa2186121a53152b719cadff
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Drallion uses the same touch panel as Sarien. Copy the deivce
from Sarien.
BUG=b:140415892,b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8e6d2dcf4bd2ed2325137a05811af03692d40342
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35305
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MT8183_DRAM_EMCP is enabled for devices using eMCP to run at a high DRAM
frequency (e.g., 3600Mbps).
BUG=b:80501386
BRANCH=none
TEST=Memory test passes on EMCP platform
Change-Id: Icf875427347418f796cbf193070bf047844d2267
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34433
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setup EC_PCH_ARCORE_INT_L, tied to GPP_D17, and define as EC_SYNC_GPIO..
- change GPP_D17 definition to PAD_CFG_GPI_APIC_INVERT as
EC_PCH_ARCORE_INT_L is active low
- add EC_SYNC_GPIO to the group of chromeos_gpios for use by depthcharge
BUG=b:139384979
BRANCH=none
TEST="emerge_nocturne coreboot depthcharge chromeos-bootimage",
flash & boot nocturne in dev mode, verify that volume up and down
buttons work in the dev screen and that the device boots properly into
the kernel.
Change-Id: Ia43c622710fde8686c60b836fb8318931d79eb61
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
pull in the FPU VDDIO turn on to fix the power leakage problem
on FPU VDDIO and FPU CS during power on sequence.
BUG=b:138638571
BRANCH=none
TEST=emerge-hatch coreboot chromeos-bootimage
Signed-off-by: Frank_Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I3f6bf3676922e987c2e282b697a2333e2d90289e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tune I2C bus 1, 2 and 3 clock and make them meet spec.
BUG=b:140665478
TEST==flash coreboot to the DUT and measure I2C bus 1,2,3 clock
frequency less than 400KHz
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6b2a51a866e57d13fe528452e4efdcf17a72317f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35298
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. SKU1 for eMMC
2. SKU2 for SSD
BUG=b:140008849, b:140573677
TEST=Verify SSD is disabled when SKU ID = 2/4/21/22
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I827e6f1420801d43e0eb4708b8b8ad1692ef7e9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35204
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From DDR4 SPD spec:
Byte 4 (0x004): SDRAM Density and Banks
Bits [7, 6]:
00 = 0 (no bank groups)
01 = 1 (2 bank groups)
10 = 2 (4 bank groups)
11 = reserved
Bit [5, 4] :
00 = 2 (4 banks)
01 = 3 (8 banks)
All others reserved
Separate DDR3 and DDR4 banks. And extened capmb, rows, cols and ranks.
Separate DDR3 and DDR4 ORGANIZATION/BUS_DEV_WIDTH offset.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5f56975ce73d8ed2d4de7d9fd08e5ae86993e731
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on HW schematic to modify USB setting.
Drallion has two type C on left and two type A on right.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I925de209635d92ef61ccb9114efebb4b10f30e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Sets all unused sata ports to disable in the device tree
Note:
SATA4 and SATA5 are located at the bottom of the board, but there
is no connector for this. Apparently, a board with an increased
number of ports is very rare. Perhaps this is a separate variant
of the Asrock motherboard. For this reason, these ports are also
disabled
Change-Id: I5b3ad372f1d6607cc7b4a78e3c59d2a5ae1d2cf5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable spi0, i2c0 and i2c1 in the “SerialIoDevMode” register for the
following reasons:
1. when the AMI BIOS is used, these pci devices are disabled in
lspci.log;
2. there are no pads in the inteltool.log that use the functions of
these buses
Change-Id: I01ab10eb3fd41e81a1726805247c2b472d72287c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35070
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The string "register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" was mistakenly
taken from the Intel KBL-RVP8 devicetree.cb. Remove it, since the i2c4
bus is disabled in the "SerialIoDevMode" register
Change-Id: I44ecd5c22efd66b02a2851dc14a1a95421f39a71
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1) VR domains current limit Icc max for Sky/Kaby Lake S is set based
on the processor TDP [1]. Updates information about this
2) Sets VR voltage limit to 1.52V, as described in the datasheets [2,3]
[1] Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
[2] page 112-119, 6th Generation Intel(R) Processor Families
for S-Platforms, Volume 1 of 2, Datasheet, August 2018.
Document Number: 332687-008EN
[3] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I6e1aefde135ffce75a5d837348595aa20aff0513
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Based on HW schematic to modify PCIE setting.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia744a6f3cba76c507c1c43b0a981cb6d89c1a40f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Use sku-id to load the SAR values for Bloog device.
BUG=b:138180187
BRANCH=octopus
TEST=build and verify load Bloog SAR by sku-id
Cq-Depend: chromium:1771477
Change-Id: Id0bc2609fd1c4eaeb380f8f1532ab30d34e2aeb3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To avoid possible panel failures due to incorrect timing settings for
PTN3460, the internal graphic device should be disabled.
Change-Id: Ie0b9ed99fb78461bb48d6f2ff328643cd8c2cd15
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Rename the table from Liara specific to simply specifying
that it's using 2T command rate
BUG=139841929
TEST=build and do stress test
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6e10b95c8aea50e68d8a3b710f30dda4f6b807d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
override 'uint32_t sku_id(void)' so that lib_sysinfo.sku_id get a
correct value in depthcharge
BUG=b:140010592
BRANCH=none
TEST=boot treeya board, in depthcharge stage, lib_sysinfo.sku_id
print correct value.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I631f62021e8104a69a43667a811c9c23e3105596
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Magf - <magf@bitland.corp-partner.google.com>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Padmelon board code was written for Merlin Falcon (family 15h models 60h-6fh),
but as the needed binaries are not yet merged (commit 33615), a config
HAVE_MERLINFALCON_BINARIES was added. If the binaries are not available,
the board defaults to Prairie Falcon, which use the same binaries as Stoney
Ridge. Once the binaries are merged, the config will be eliminated. Fan
control is done through F81803A SIO, and IRQ/GPIO and other board
characteristics are the same regardless of Merlin Falcon or Prairie Falcon.
Padmelon board was created to accept Prairie Falcon, Brown Falcon and Merlin
Falcon. The requested development was for Merlin Falcon. There are some small
spec changes (such as number of memory channels) between SOCs. Brown Falcon
was not investigated, Prairie Falcon is very similar to Stoney Ridge.
Started from Gardenia code, added changes created by Marc Jones and finally
revised against schematic, which added changes to GPIO settings.
BUG=none.
TEST=Both versions tested and boot to Linux using SeaBIOS.
Change-Id: I5a366ddeb4cfebd177a8744f6edb87aecd4787dd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Select NO_UART_ON_SUPERIO as the SoC internal UART is used.
The current code is working, so this is just a cosmetic fix to remove
some unused options from Kconfig.
Change-Id: I206557c397da74b572e669feb1e38f0c8473d0d9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35151
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drallion will use soldered down memory and use
GPP_F12 to GPP_F16 indicates mem_id.
BUG=b:139397313
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib5ada54fd2b8f358b59de8089e5405cf3e34825a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Its entirely no-op and is getting in the way of real hardware timers for
power9/talos ii.
Change-Id: I2d21d4ac3d1a7d3f099ed6ec4faf10079b1ee1d1
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35082
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per GT7375P programming guide rev0.4, we want to enforce a delay
of 120ms after the reset is completed, before HID_I2C starts.
BUG=b:140276418
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Id69a9db996bcd9001ef850c50898fbd55327b4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Summary:
This patch calls monolake board specific function to query
settings stored in VPD binary blob to configure FSP UPD
variable HyperThreading.
Test Plan:
* Build an OCP MonoLake coreboot image, run following command
to initialize RW_VPD and insert HyperThreading key:
vpd -f build/coreboot.rom -O -i RW_VPD -s 'HyperThreading=0'
* Flash the image to MonoLake, boot and observe following
message in boot log:
Detected 16 CPU threads
If RW_VPD partition does not exist, or if HyperThreading
key/value pair does not exist, the boot log has:
Detected 32 CPU threads
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I799d27734fe4b67cd1f40cae710151a01562b1b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Remove duplicated code and instead use the IPMI KCS driver, which provides
the same functionality.
Change-Id: I419713c9bef02084cca1ff4cf11c33c2e3e8d3c1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 [1]
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The pad configuration in this patch was
generated using the pch-pads-parser utility [2]. The inteltool dump
before and after the patch is identical (see notes)
Notes:
1. For some reason, GPIO RX State (RO) for the GPP_F4 and GPP_G10
changed the value to 0, but this doesn't affect the motherboard
operation. Perhaps this is because PAD_CFG1_GPIO_DRIVER is set to
PAD_CFG_GPI_INT(), and the pad is not actually connected. So far I
haven't circuit diagram to check this out.
2. According to the documentation [1], the value 3h for RXEVCFG is
implemented as setting 0h.
3. If the available macros from gpio_defs.h [3] can't determine the
configuration of the pad, the utility [2] generates common
_PAD_CFG_STRUCT() macros
[1] page 1429,Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 2 of 2,
February 2019, Document Number: 332691-003EN
[2] https://github.com/maxpoliak/pch-pads-parser/tree/stable_1.0
[3] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
Change-Id: I01ad4bd29235fbe2b23abce5fbaaa7e63c87f529
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add support for the X11SSH-TF which is based on Intel KBL.
Working:
* SeaBIOS payload
* LinuxBoot payload
* IPMI of BMC
* PCIe, SATA, USB and M.2 ports
* RS232 serial
* Native graphics init
Not working:
* TianoCore doesn't work yet as the Aspeed NGI is text mode only.
* Intel SGX, due to random crashes in soc/intel/common
For more details have a look at the documentation.
Please apply those patches as well for good user experience:
Ica0c20255f661dd61edc3a7d15646b7447c4658e
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Change-Id: I2edaa4a928de3a065e517c0f20e3302b4b702323
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Adjust CID to allow for Windows driver to attach without breaking
functionality under Linux. Same change made as to google/cyan
(which uses same Realtek RT5650 codec) in commit 607d72b.
Test: build/boot Windowns 10 on google/buddy, observe audio
drivers correctly attached to codec and Intel SST devices.
Change-Id: I839acc8427ee9b5c425885858a513e9b0b9d0f93
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Drallion will change debug port UART from 2 to 0. Followed HW
schematic to modify it.
BUG=b:139095062
BRANCH=N/A
TEST=Build without error
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib2bcded8de3c9fb2c0a4ccbd002b1f219bccceb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Enable acoustic noise mitgation for hatch platform, the slow slew rates
are fast time dived by 8 and disable Fast PKG C State Ramp(IA, GT, SA).
BUG=b:131779678
TEST=waveform test and reduce the noise level.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I49e834825b3f1e5bf02f9523d7caa93b544c9d17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This removes the need to select ARCH_ARM in SOC Kconfig
Also don't define the default as this result in spurious lines in the
.config.
Change-Id: I1ed4a71599641db606510e5304b9f0acf9b7eb88
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31313
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current HWID for drallion is reported as invalid by chrome, generate
new valid HWID with the following command and taking last 4 digits.
`printf "%d\n" 0x$(crc32 <(echo -n '$1'))`
BUG=b:140013681
Change-Id: I410d37fc3f3372e9420d674b65f2c9a704b670f2
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
During boot sequence sometime touchscreen reset keeps failing. Also, kernel
dmesg shows "dmesg:i2c_hid i2c-GDIX0000:00: failed to reset device" message.
This adds around 4 more seconds to the boot sequence. Setting the appropriate
delay of 120ms between enable and reset for Goodix Touchscreen helps to
synchronize and address this failure. This value is 120 ms as per Goodix Spec.
BUG=b:138413748
BRANCH=None
TEST=Built and tested on Hatch system
Change-Id: I15005c568f285ec7bad9a0bec4498e2fdd20782b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34626
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is LVDS bridge, I assume this was lost while upstreaming
or converting boards to variants.
Change-Id: I816a6b4035c4e935150cc77089c4224eee719c10
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Device is present in devicetree but not included in
the build.
Change-Id: I8555d94902e94c623d8fbe6f1a4ffe7637988530
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
New emmc DLL values for Kindred
BUG=b:136784418
BRANCH=none
TEST=Boot to OS 100 times on Kindred proto 1 board.
Change-Id: I52acb445c47fcdb9b60512dd501d810b1ae4dc10
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35041
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drallion doesn't have on board LAN, remove GBE bin file config.
BUG=b:139906731
TEST=emerge-drallion coreboot chromeos-bootimage and check
image-drallion.bin not include GBE region
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ifbc295afd8d875b5098b0ce75252b51523a5c76e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mathew King <mathewk@chromium.org>
Drallion will use soldered down memory. Add dummy spd file.
BUG=b:139397313
BRANCH=N/A
TEST=Build and check cbfs has the dummy spd.bin
Change-Id: Ife59c2dd689d72b117f30e832a3ce7eed4fa4220
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35113
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The file chip.h has a special purpose for defining the
configuration structure used in static devicetree.
Change-Id: If0289c29ca72768009c1b7166311bc4c3cee4171
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This provides stack guards with checking and common
entry into postcar.
Change-Id: If0729721f0165187946107eb98e8bc754f28e517
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34973
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This provides stack guards with checking and common
entry into postcar.
The code in cpu/intel/car/romstage.c is candidate
for becoming architectural so function prototype
is moved to <arch/romstage.h>.
Change-Id: I4c5a9789e7cf3f7f49a4a33e21dac894320a9639
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34893
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These are required to cover the absensce of .data and
.bss sections in some programs, most notably ARCH_X86
in execute-in-place with cache-as-ram.
Change-Id: I80485ebac94b88c5864a949b17ad1dccdfda6a40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Board has CAR_GLOBAL_MIGRATION=n and can use .bss for a
variable that was previously declared with CAR_GLOBAL.
Test for !defined(__PRE_RAM__) can be transformed into
ENV_RAMSTAGE here as the warnings about invalid bmcinfo
structure do not need to be repeated in SMM console, which
is generally disabled anyways due to DEBUG_SMI=n.
Change-Id: I6b63213484107fa0eeb0d952d8766916b44a3c4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Kukui AP doesn't remember if the last AP reset was due to AP watchdog.
We need to enable CHROMEOS_USE_EC_WATCHDOG_FLAG so that it will query
the reset reason from EC.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=1. run 'mosys eventlog clear; stop daisydog; echo > /dev/watchdog'
2. wait for watchdog reset
3. check 'mosys eventlog list | grep watchdog'
Change-Id: I053cc7664bbaf0d3fcae26ba9481a0ad700dca90
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
EFP1 is configured as 'DisplayPort with HDMI/DVI
compatibility'. Using this setting 4K monitor is configured
into lower resolution.
Change EFP1 setting to 'HDMI/DVI'
The next addtional small changes are made in VBT:
UEFI GOP Driver
Child Device 2 = LFP
Child Device 3 = EFP1/LFP
LFP Panel configuration Y-Res of Panel #10 = 1920
BUG=N/A
TEST=LCD and HDMI on Facebook FBG1701
Change-Id: Idc694b15ff94b83291a8c8252e269b7e6d96f87b
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35043
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Changes to the sandybridge memory init code (both MRC
and native) now require SPD data on all populated channels
in order for dimms to be detected properly, so copy
spd_data[0] to spd_data[2], as LINK always has 2
channels of memory down.
Test: boot google/link, observe onboard RAM correctly
detected on both channels
Change-Id: Id01d57d5e5f928dfc1cd9063ab1625c440ef2bbe
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DRAM_SIZE_MB should be the maximum size (255GiB / -m 261120M)
that’s possible with QEMU on AArch64 virt because it tries to search
the DRAM_SIZE_MB range to find the true memory size.
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Change-Id: Id479c0b18d1e1adceecdcca13e36119b95617e6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In the next board version, we will use GPP_D9 as enable control for touch
screen.
BUG=b:137133946
TEST=build
Change-Id: I213d0878bfca1ce4059ec0393f59d8e79e1b274c
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
sx9310 and FPMCU are not used in Kindred.
BUG=none
TEST=build
Change-Id: Ied09d4bdb899d991131a75d7c848ff8637022f53
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When upstreamed, GPIO and RAM config for clapper variant was taken
from an older branch, leading some boards to fail to boot.
Update based on chromium branch firmware-clapper-5216.199.B,
commit 362d845 [baytrail: implement baytrail technical advisory 556192]
Change-Id: I099ee2cd0833e4b9ab093663c4549c79ec044127
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 38dbd68920.
Reason for revert:
ODM helped to verify w/ BT runtime suspend disabled + revert this change
And issue is gone. so I revert this change
see the test result in
https://partnerissuetracker.corp.google.com/issues/136039607#comment32
Change-Id: I248e9613cc39247a2bb88270c234c7d36d0ff60f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
These variants are to support the sarien and arcada boards
with CML SOC, the drallion variant will be used to support the
upcoming drallion board.
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: I766bdccb6f8b6924d6ae1abbe57035f4ff1f6f17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Declare the following panel for Kodama:
- AUO B101UAN08.3
BUG=b:139699622
TEST=builds Kodama image and working properly
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I3f688ffd0ece6afac08d353ab5a6cf1cf876b32f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35001
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The panel description may be pretty large (for example, 1.3k for BOE
TV101) due to init commands and we should only load the right config
when display is needed.
BUG=None
TEST=make -j; boots and see display on Krane.
Change-Id: I2560a11ecf7badfd0605ab189d57ec9456850f75
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
These platforms use different signature for this function, so
declare them with different name to make room in global namespace.
Change-Id: I77be9099bf20e00ae6770e9ffe12301eda028819
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34909
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Treeya doesn't support the keyboard backlight.
BUG=b:135551210
BRANCH=grunt
TEST=emerge-grunt coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I02dfc77d3cb7ac00b3f10d577d92775db99c1bdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Use AGPIO 10 as the EC sync interrupt for MKBP events for sensor data.
Reference to Aleena project.
BUG=b:135551210
BRANCH=grunt
TEST=emerge-grunt coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ie0b719ebce90710bca2109b7ff255e19329f9cac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Enable ACPI TBMC notification on tablet mode change to support
convertible treeya devices.
BUG=b:135551210
BRANCH=grunt
TEST=emerge-grunt coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Id0618c8df66267b88008dc5057892de6b530629f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Synaptics touchscreen
BUG=b:139699619
TEST=emerge-grunt coreboot chromeos-bootimage
flash bios image to DUT and make sure the touchpad and
touchscreen can work
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I002badd49e678e1c32c802352923ca51efb45cef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
coreboot would clear CMOS by request via IPMI command, for example
BMC can issue "bios-util server --boot_order enable --clear_CMOS"
to set the request and reboot the system, then coreboot would clear CMOS
on the next boot.
Tested on Mono Lake
Change-Id: I21d44557896680cfac3c3b6d83e07b755b242cad
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34857
Reviewed-by: Johnny Lin
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Port_List is an array of 8 elements, and GCC 9 is warning that there
are no 'others' when all 8 elements are explicitly initialized, which is
causing the build to fail. Remove the 'others => Disabled' clause to
silence this.
Change-Id: Id082e7a76641438f3fb4c4d976dbd254a7053473
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34918
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Print an error message and die if the PCI device cannot be found.
Change-Id: I10c58502658ebf12d1a8fe826ee7d47a618fd1c8
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1403000
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
DqByteMapCh0 and DqByteMapCh1 are declared adjacently in the
FSP_M_CONFIG struct, so it is tempting to begin memcpy at the address of
the first array and overwrite both of them at once. However, FSP_M_CONFIG
is not declared with the packed attribute, so this is not guaranteed to
work and is undefined behaviour to boot. It is cleaner and less tricky
to copy them independently. The same is true for DqsMapCpu2DramCh0 and
DqsMapCpu2DramCh1, so we change those as well.
Change-Id: Ic6bb2bd5773af24329575926dbc70e0211f29051
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 136538{8,9}, 140134{1,4}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33135
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DqByteMapCh0 and DqByteMapCh1 are declared adjacently in the
FSP_M_CONFIG struct, so it is tempting to begin memcpy at the address of
the first array and overwrite both of them at once. However, FSP_M_CONFIG
is not declared with the packed attribute, so this is not guaranteed to
work and is undefined behaviour to boot. It is cleaner and less tricky
to copy them independently. The same is true for DqsMapCpu2DramCh0 and
DqsMapCpu2DramCh1, so we change those as well.
Change-Id: If394f14c4a39d6787ae31868241229646c26be7a
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1365730, 14013{38,39,40,42,43}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It probably doesn't make sense to continue if the CK804 isn't found, and
doing so would perform uninitialized reads of the busn and io_base
arrays anyway, so let's return early.
Change-Id: I13c663314496caf51a57da7f27f9ea24e3d7fcbd
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1370586
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Level trigger is recommended setting for touchscreen interrupt of
kohaku, so we would change it as the recommedation.
BUG=b:139179200
BRANCH=none
TEST=Verified touchscreen works on kohaku
Change-Id: Ibbcdbe3ab555d014048f66ff527e539c5b566187
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When entry to romstage is via cpu/intel/car/romstage.c
BIST has not been passed down the path for sometime.
Change-Id: I345975c53014902269cee21fc393331d33a84dce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is based on the hatch variant
BUG=b:138879565
TEST=FW_NAME="akemi" emerge-hatch coreboot depthcharge intel-cmlfsp
chromeos-bootimage look for image-akemi.*.bin generated under the
/build/hatch/firmware/
Change-Id: I1a868839e2c598f8052d37c99713bc58b21e887c
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Disable SATA controller and SATA port 1 for eMMC SKUs
BUG=b:132918661
TEST=Verify SSD is disabled when SKU ID = 2/4/21/22
Change-Id: I6d95ff94b079a564f74c19739370101899843f00
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34789
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Peichao Wang