Replace the use of the old device_t definition inside
northbridge/intel/e7505.
Change-Id: Ie819f380ec06667e11bcff3e9e993126a86b2c89
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16469
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
northbridge/intel/fsp_rangeley.
Change-Id: I4c1e6af64fe70211db2fafdba9f39182dfea66fc
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16470
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Previously the ME PCI interface (HECI) was being reported as present in
the DMAR ACPI table even when ME firmware was missing or the PCI device
was hidden and HECI would be unresponsive.
Now we check via the PCI config space itself to verify if the HECI
is present or not.
Note that this test could fail if ME firmware is present but
HECI is disabled in devicetree, because it would not advertise that the HECI
exists even though there is a running ME. Perhaps this behaviour is desirable
because in this case you won't see the HECI in the lspci tree anyway.
Change-Id: Ib692d476d85236b4886ecf3d6e6814229f441de0
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16330
Tested-by: build bot (Jenkins)
Reviewed-by: Swift Geek <swiftgeek@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is necessary for PCI express graphics card add-ons,
otherwise the pci allocator cannot fit the mmio for the
add on card into the space it has available and the OS
turns off the card. Old value was 1GiB.
Change-Id: I606994501b15e636fe209d1ed4b3d3f73b42bf5c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
No more hang on DMI init when wait for DMI is re-enabled.
Previously the virtual channel arbitration table was not being
set up in the south/north bridges causing invalid DMI state.
This has been tested on GA-G41M-ES2L with patches following.
An NVIDIA GT218 card was detected by the OS and displayed using
the nouveau driver with no blobs.
Change-Id: I35e03c40f5f7aa4915afd5d26db7ab053abcf0cd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16491
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
According to "G45: Volume 3: Display Register
Intel ® 965G Express Chipset Family and Intel ®
G35 Express Chipset Graphics Controller" some registries
are set incorrectly in gm45/gma.c.
Some values are changed after comparing them with the values
the i915 linux kernel (3.13 was used) module sets while modesetting.
The values were obtained using 'intel_reg' from intel-gpu-tools,
during a normal boot and with 'nomodeset' as a kernel argument.
Some registers that don't exist on gm45 are set in gma.c, which is
probably the result of copying code from a more recent intel
northbridge.
The result is that that gm45 laptops with wxga displays still work as
before. gm45 laptops with wxga+ or higher resolution now just work,
where previously a black screen was shown.
TEST: build with native graphic init and flash on a gm45 target, like
lenovo x200.
Change-Id: If66b60c7189997c558270f9e474851fe7e2219f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16217
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Replace the use of the old device_t definition inside
northbridge/intel/i945.
The patch has been tested both with the arch/io.h definition of
device_t enabled and disabled in order to ensure compatibility
while the transaction takes place.
Change-Id: I041c150a7b50261e26955ad9287ef05b9a06e412
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16371
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Replace the use of the old device_t definition inside
northbridge/intel/sandybridge.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I35cc76ec7b6baa216666d06f6f325f43ac69067e
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16409
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
On i945 the vram size is the default 8mb. It is also possible
to set it 1mb or 0mb hardcoding the GGC register in early_init.c
The intel documentation on i945, "Mobile Intel® 945 Express Chipset
Family datasheet june 2008" only documents those three options.
They are set using 3 bits. The documententation also makes mention
of 4mb, 16mb, 32mb, 48mb, 64mb but not how to set it.
The other non documented (straight forward) bit combinations allow
to change the VRAM size to those other states.
What this patch does is:
- add those undocumented registers with their respective vram size to
the i945 NB code;
- make this a cmos option on targets that have this northbridge.
TEST: build, flash to target, set cmos as desired and boot linux.
On Debian it can be found using "dmesg | grep stolen".
NOTE: dmesg message about reserved vram are quite different depending
on linux version
Change-Id: Ia71367ae3efb51bd64affd728407b8386e74594f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This allows to set the preallocated memory for the IGD on x4x
using a cmos option.
If no cmos option is found a default value of 64M is used.
TESTED most options on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
352M also works in contrast with gm45 where it is known to cause issues
with certain ram combinations.
Change-Id: I9051d080be82f6dfab37d353252e29b2ed1fca7f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15492
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The Intel documtentation, "Intel ® 4 Series Chipset Family"
mentions the possibility of 1, 4, 8 and 16M of preallocated
memory for the IGD, but does not document this.
This allows to set those undocumented values.
TESTED on ga-g41m-es2l with 2G dimm in one slot and 2x2G.
Change-Id: I92beb8d78907d4514a5aaf69248dd607dcf227c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15491
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now hardcode maximum memory frequency capability to 800MHz, as
all chipsets in x4x family support PC2-6400 according to the datasheet.
CAS latency detection also relies on this, and has been cleaned up.
Ram initialization does not work with FSB 1333MHz / DDR2 800MHz combination,
so disable this combination for now, and reduce to 667MHz instead.
Still don't know why this is the case, but FSB1333/667 works.
These changes should now allow existing configurations to continue working,
while providing support for previously unworking configurations, due to
previous buggy CAS latency detection code.
TESTED: on GA-G41M-ES2L
CPU: E5200 @ 2.50GHz (FSB 800MHz)
2x 1GB 667MHz hynix worked @ 667
1x 2GB 800Mhz ARAM worked @ 800
1x 1GB 667Mhz StarRam worked @ 667
2x 2GB 800Mhz (generic) worked @ 800
Change-Id: I1ddd7827ee6fe3d4162ba0546f738a8f9decdf93
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15818
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Match the definition and use of these variable with haswell, such that
DCACHE_RAM_MRC_VAR_SIZE is not included in DCACHE_RAM_SIZE.
Change-Id: I5af20f63cd0cb631d39f7c7fe0e2a99ebd3ce986
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15761
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix and use the failsafe CAS detection logic rather than
recalulating the values from raw SPDs.
Tested on GA-G41M-ES2L with 2x2GB DDR2-800 DIMMs
(which worked before and still work)
Change-Id: I6af0f1705d099f7bcbff8c9baa94a68dae689e01
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15726
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
If S3 support was implemented for this platform later on, use
romstage handoff structure instead.
Change-Id: I03c1e07a7fcc17c27203d0c4e32e3958f2ba5273
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15716
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
If S3 support was implemented for this platform later on, use
romstage handoff structure instead.
Change-Id: Ib0cf3ad41753baee26354c5ed19294048e7fb533
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15715
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
Previously, any 800MHz DIMMs were being slowed to 667MHz
for no reason other than there was a bug in the maximum
frequency detection code for the MCH.
Change-Id: Id6c6c88c4a40631f6caf52f536a939a43cb3faf1
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15257
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Broken with commit:
5c10abe nb/intel/sandybridge: increase MMCONF_BASE_ADDRESS
Available sandybridge/systemagent-r6.bin has MMCONF hard-coded
at some places and samsung/lumpy fails at boot here:
CBFS: Locating 'mrc.bin'
CBFS: Found @ offset 9fec0 size 2fc94
System Agent: Starting up...
System Agent: Initializing
These are the last lines as captured over USB debug.
Change-Id: I441847f0e71a5e1be9c8ef6a04a81eb7bdd8a6d9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15328
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Without RELOCATABLE_RAMSTAGE have WB cache large enough
to cover the greatest ramstage needs, as there is no benefit
of trying to accurately match the actual need. Choose
this to be bottom 16MiB.
With RELOCATABLE_RAMSTAGE write-back cache of low ram is
only useful for bottom 1MiB of RAM as a small part of this gets used
during SMP initialisation before proper MTRR setup.
Change-Id: Icd5f8461f81ed0e671130f1142641a48d1304f30
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15249
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of programming unsupported CAS use the highest supported
value. Start at DDR3 maximum of CAS 18T.
Increase error message verbosity level.
Useful for overclocking.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
Allows to run a DDR3-1600 DIMM at 933Mhz.
Change-Id: I2e8aadd541f06fa032ad7095c9a2d5e3bb7613f3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15217
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Calculate the value from current DDR frequency.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
Change-Id: I57ffbfeb291fc2fede278d18527993e7432e9bd8
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15184
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Set max_mem_clock_mhz in devicetree to 933Mhz.
Allows to run the memory at up to DDR3-1866.
The same frequency was allowed within the first vendor bios,
but Lenovo than decided to limit it to DDR3-1333.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
The RAM is now running at DDR3-1600 instead of DDR3-1333.
This gives about 4% performance increase in glmark2 using the
Intel GPU.
Change-Id: If15be497402d84a2778f0434b6381a64eda832d6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15158
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This is more of ACPI S3 resume and x86 definition than CBMEM.
Change-Id: Iffbfb2e30ab5ea0b736e5626f51c86c7452f3129
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15190
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Instead of hardcoding the PCI mmio size read it from devicetree.
Set a default value of 2048 MiB and 1024MiB for laptops without
discrete graphics.
Tested on Sandybridge Lenovo T520.
Change-Id: I791ebd6897c5ba4e2e18bd307d320568b1378a13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15140
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove code duplication and use the common function
store_current_mrc_cache instead.
No functionality is changed.
Tested on Sandybridge Lenovo T520.
Change-Id: I4aa5463f1b1d5e1afbe44b4bfc659524d86204db
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15074
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Previously, 0x0 was the value being used for an unpopulated dimm
on spd[62], however some DDR2 dimms have 0x0 as a valid value.
Now use 0xff which is an unused value even on DDR2/DDR3.
Change-Id: I55a91a6c3fe3733a7bb2abc45ca352c955c07c99
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/15058
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Setting the size of the preallocated memory for the igd is done
using a cmos parameter, gfx_uma_size. This was limited to a subset of
all available sizes, that were already implemented elsewhere
in the northbridge code.
What this does is change the cmos parameter to 4 bits instead
of 3 bits to accomodate all vram sizes.
It also adds a sane default of 32mb that already was in place.
The northbridge code that reads this cmos parameter is
also changed for this new cmos settings.
352M is disabled since it causes issues on systems with 4GB or more ram.
TEST: Build, flash target. Clear cmos by corrupting
the checksum (nvramtool -c something).
Set a desired value in gfx_uma_size using nvramtool.
"dmesg | grep stolen" to see what is actually allocated.
Change-Id: Ia6479d03f1abe6d0c94bd7264365505e8f8eaeec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14900
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The values were obtained from vendor bios at runtime.
I am not 100% sure of the sequence required to initiate them,
but guessed from the gm45 code. There may be some status bytes
needed to be polled during the sequence that is missing,
but as I don't have bios writer's datasheet it's very hard
for me to know.
Change-Id: Idd205e0bab5f75e01c6e3a5dc320c08639f52db8
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/14925
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Mask out the bit that doesn't fit in 32bits, so gcc 6.1 is happy
Change-Id: I13e2b41742206b8d86b90314b80cc324c00ae637
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14639
Reviewed-by: Damien Zammit <damien@zamaudio.com>
Tested-by: build bot (Jenkins)
The PLL will never lock if the requested frequency is already set.
As the fallback may request the same frequency again exit early
to prevent a hang.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Change-Id: I625b2956346d8c50cca84def6190c076bf99dbec
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14174
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the following fallbacks:
* Try decreasing clock frequency.
In case of DDR1600 the next possible value of DDR1333 is being used.
* Try decreasing clock frequency.
In case of DDR1333 the next possible value of DDR1066 is being used.
* Disable failing channel.
The system may be able to boot with a single channel enabled.
The fallbacks are untested.
Change-Id: I3be7034ad25312b3ebf47a54f335a3893f8d7cc1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14173
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The LVDS port is configured to accept data from pipe A, but the panel
fitter and VGA were attached to pipe B.
Changes to VGACNTRL:
- select pipe A instead of pipe B.
- disable VGA centering to fix jitter.
TEST=Build and run on Thinkpad X200 in both text and framebuffer modes.
Change-Id: I2356f264580d8b021952c217de3477291d866f98
Signed-off-by: Nick High <nhigh@openmailbox.org>
Reviewed-on: https://review.coreboot.org/14524
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Fix regression introduced by:
Ib48fe8380446846df17d37b22968f7d4fd6b9b13
Don't run channel_test on S3 resume as it overrides memory
that might be in use.
Fixes MCE events reported by the GNU/Linux kernel that
low memory has been modified.
Reset on failed s3 resume.
Change-Id: Ibadea286619c7906225f86a93aaa0b4caf26cabe
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Always use MRC cache if possible.
Added a CRC16 array to make sure the DIMMs haven't been replaced.
In case one of the CRC's doesn't match, start normal RAM training.
Use new fallback in case of broken mrc cache.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Test result:
The system boots a lot faster using the MRC cache.
On swapping DIMMs the CRC16 doesn't match and normal ram training
is started.
Change-Id: Ib48fe8380446846df17d37b22968f7d4fd6b9b13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14172
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In error case die in top level function.
No functionality is changed.
Change-Id: Ie15b01184d40bdbce20d49dcab2f9fb607068c7a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14171
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Return errors to top level ram init function.
Required by the folowing series to implement a fallback.
No functionality is changed.
On error case the system still halts in every test.
Change-Id: I6278c4a1d7b4a96be8988a60671fc3d72cd6cb3d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14170
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
In order to add a fallback mechanism, move the ram training code
into a new function. This function will be called multiple times
and must return error or success to the calling function.
Change-Id: I5ee1b3a528290d8252d236b9152b81291736958a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14169
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
It's required to store the dimm_info in ramctr_timing as only ramctr_timing
is written to mrc cache.
Allows to fill SMBIOS type 17 if mrc cache is used.
Change-Id: I7634b05069df307d471938d9854997a018de81b3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14168
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The Intel i3100 northbridge code is the only user of
cache_ramstage(). Therefore, place it next to the sole
consumer.
Change-Id: If15fb8d84f98dce7f4de9e089ec33035622d8f74
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14097
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of manually including udelay_io.c in each romstage,
select UDELAY_IO for all i3100 boards in the chipset.
Change-Id: Ia66a0561c75777a9e98bb87117859808a2ff3732
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13786
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Instead of manually including udelay_io.c in each romstage,
select UDELAY_IO for all i810 boards in the chipset.
Change-Id: Ifda7dcfdf37b6affce838ee96ca6382b2d4be8c3
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13784
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Instead of manually including udelay_io.c in each romstage,
select UDELAY_IO for all i830 boards in the chipset.
Change-Id: I0a63ddd3c5e43ea65f776385f54eceb6569751ac
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The sourcecode is 99% the same. Only two lines differ, but not
in functionality.
Also rename mrccache.c -> mrc_cache.c
Tested-on: boot + suspend/resume on x220
Change-Id: I36f79d066336f223b608c70c847ea6ea6e4ad287
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14007
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The mrc_cache definition and the struct mrc_container are the same
over all intel platforms.
Change-Id: I128a4b5693d27ead709325c597ffe68a0cc78bab
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/13998
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Commit 71512b2c (northbridge/i945/gma: fix build error with native graphics init)
unintentionally changed the code to ignore the NVRAM setting
`tft_brightness`. Revert that hunk to restore the original behavior.
Change-Id: Iffdfc5272732bad3476f35ddac1f5a7564270531
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14002
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Instead of manually including udelay_io.c in each romstage,
select UDELAY_IO for all i440BX boards in the chipset.
Change-Id: I411191927f3fba1d0749edcf79378e8013fb195a
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13781
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This is a step towards isolating the timer drivers.
Change-Id: I4c9349054be0cf520cd4407be9fb393b664223a4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13922
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Sandy and Ivy Bridge processors use the same socket, and a mainboard
with the socket can support both types of CPUs. However, they use
different native graphics init code for LVDS and cause a crash if
running the wrong code.
This change detects the CPU type and then selects the right code to
run. It will add some more code in ramstage. It also merges the
{SANDY,IVY}BRIDGE_LVDS symbol to one SANDYBRIDGE_IVYBRIDGE_LVDS.
Tested on a Lenovo T520 with i7-2630qm and i7-3720qm
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Change-Id: I4624759f9c92d56d547db1ab4b9a1d611a182a91
Reviewed-on: https://review.coreboot.org/12087
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Tested-by: build bot (Jenkins)
Instead of hardcoding the maximum supported DDR frequency to
800Mhz (DDR3-1600), read the fuse bits that encode this information.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Change-Id: I515a2695a490f16aeb946bfaf3a1e860c607cba9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The code can't handle cyclic zero runs. Make sure it will never
wrap around by setting the top-most bit to constant one.
Fixes "Mini channel test failed (2)".
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Change-Id: I55e610d984d564bd4675f9318dead6d6c1e288a3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13853
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
I first found the missing of #include guards when I tried to include
both sandybridge/gma.h and sandybridge/sandybridge.h, but
sandybridge.h includes gma.h in it and gives a compile error.
Change-Id: I13fdb8014b82e6065be2064137b7ea10062deaca
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/13775
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Improved version of
I1a115a45d5febf351d89721ece79eaf43f7ee8a0
The first version wasn't well tested due to the lack of hardware
and it was to aggressive.
With timC being direct function of timB's 6 LSBs it's critical to match
timC and timB.
Some tests increments the value of timB by a small value,
which might cause the 6bit value to overflow, if it's close
to 0x3F.
Increment the value by a small offset if it's likely
to overflow, to make sure it won't overflow while running
tests and bricks the system due to a non matching timC.
In comparission to the first attempt, only 4 out of 128 timB values
are considered bad.
Needs test on real hardware !
Fixes a "edge write discovery failed" on my test system.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Change-Id: If9abfc5f92e20a8f39c6f50cc709ca1cedf6827d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13714
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some vendors store lower frequency profiles in the regular SPD,
if the SPD contains a XMP profile. To make use of the board's and DIMM's
maximum supported DRAM frequency, try to parse the XMP profile and
use it instead.
Validate the XMP profile to make sure that the installed DIMM count
per channel is supported and the requested voltage is supported.
To reduce complexity only XMP Profile 1 is read.
Allows my DRAM to run at 800Mhz instead of 666Mhz as encoded in the
default SPD.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
Change-Id: Ib4dd68debfdcfdce138e813ad5b0e8e2ce3a40b2
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13486
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Use printram() in more places and use printk() only where
it makes sense.
Remove spamming "MRd: %x <= %x\n".
Use common syntax for timing output.
Change-Id: I38965967a029994112d7ab63afd4d9968a7728c5
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13414
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Issue observed:
The PCIe Root port shows up in GNU/Linux but no PCIe device
is being detected.
Test system:
* Gigabyte GA-B75M-D3H (Intel Pentium CPU G2130)
* Lenovo T530 (Intel Core i5-3320M CPU)
Problem description:
The PEG Root port link training on Ivy Bridge needs to be manually started.
Problem solution:
The bits are set in early_init to meet PCIe reset timeout of 100msec.
The bits should be set in PCI device enable function, but this causes the
PCI enumeration to not detect the card, as it's still booting. Adding
a fixed delay of 100msec resolves this problem, but this would
increase boot time.
Read the PCI base revision mask to make sure it's any IvyBridge CPU.
Don't run the code on MRC path as it has its own PEG initilization code.
Tested with:
* Nvidia NVS 5400M (PCIe2)
* ATI Radeon HD4780 (PCIe2)
* Nvidia GeForce 8600 GT (PCIe1)
Untested:
* PCIe3 devices
Final test results:
The PEG device shows up under GNU/Linux and can be used without issues.
Change-Id: Id8cfc43e5c4630b0ac217d98bb857c3308e6015b
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/11917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Use shared gpio code from common folder.
Bd82x6x's gpio.c and gpio.h is used by other southbridges
as well and will be removed once it is unused.
Change-Id: I8bd981c4696c174152cf41caefa6c083650d283a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13614
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
It looks like the falling timing was missing the shift offset.
Not sure if this was intentional, I guess not.
Tested on my hardware and produced no regressions.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Please test on real hardware !
Change-Id: Id8c60217093a48bf322f406ea258c10a02c936e8
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13682
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Otherwise the image is simply unusable.
Change-Id: I1e2562ba17279d14dc73b05e4f8fa493e06fbcd2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13699
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In the same time remove few native gfx options which were improperly set
and only added dead code to the binary.
Change-Id: I4ed3fec03a1655ae0a779c3aa3845de273cb12e1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13649
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
This is needed for stout EC init.
Change-Id: I5c73499c17763229840152a473a2d820802ee2f6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13535
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This reverts commit 0e06f5bd70.
It breaks gm45 and also does some magic without being asked too. It
disables bridge devices permanently if no device was found on the se-
condary bus. In a simple notebook world this might be ok, but it breaks
hot-plugging and late detection (if a secondary bus device comes up too
slow for the firmware to detect and the OS has to enumerate it).
Change-Id: Ia2010640d7c55b0bdd44164b81c75dd4be50410b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/13609
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Walk the bus and try to find enabled devices.
Disable the PEG port if no devices are attached.
Change-Id: I67fcc831fd78ecc6dba83f4e0662ec7549cc2591
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Issue observed:
The system boots with 4G in channel 0 and 4G in channel 1.
The system doesn't boot with any combination of 4G + 1G in
channel 0 and 4G in channel 1.
In both cases DIMM1 failed, while DIMM0 showed no issues.
Problem description:
The CLK to CMD/CTL was off by a half clock cycle.
The find the issue I X-Y plotted timC vs timB for every
lane on the failing rank.
You can see an offset by 32 units for timB, that is not present on
other ranks.
It turns out that the XOVER CMD/XOVER CTL enable bit for DIMM1 was
missing in program_timings(), which caused the clock offset.
Problem solution:
Add two functions to calculate XOVER CMD and XOVER CTL and use both
to set XOVER in program_timings() and dram_xover().
Final testing result:
The system boots with 4G + 1G in channel 0 and 4G in channel 1.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Change-Id: I88694c86054ade77e9d8bb2f1fdaf7bc559c1218
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13415
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Previously with errors in the ram init, early cbmem was disabled.
Now that the ram is working correctly, set as early cbmem platform
and update all (1) boards to use it.
Tested on GA-G41M-ES2L
Change-Id: I5925c28821537f0e326b4f5a2ac39778e4724a3c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13131
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tidy up the code and move vga_textmode_init() later
Change-Id: I49967e7197416c955ae6c8775eac7d1a60c92d1c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13128
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- Fix bug with msbpos, it was not returning the correct result
due to typo in logic, and unsigned value needed to be negative.
- Add reclaim above 4GiB
- Fix to ME related registers near the end of raminit
Change-Id: I04acd0593a457437ee4a42e14b287b2b17a160af
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13127
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Previously, 0xa0000000 to 0xc0000000 needed to be reserved as
a non-usable memory hole because it would hang on memory i/o.
Memtest86+ now passes with no errors on both channels populated.
Tested on GA-G41M-ES2L with 2x2GiB sticks of ram.
Change-Id: Ib52a63a80f5f69c16841f10ddb896ab3c7d30462
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13125
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
VGA grub console works but display wobbles left/right
drm/i915 driver reports one error:
- [drm:i915_irq_handler] *ERROR* pipe A underrun
- Monitor does not display 1920x1080 after modeset
- Other resolutions look out of sync
Cause: suspect single bug in raminit (chipset init)
Change-Id: I2dcf59f8f30efe98f17a937bf98f5ab7221fc3ac
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12921
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fixes bug that decode_pciebar() function was bypassed due
to PCI_DEV(0,0,0) being detected as zero and function returning 0.
Change-Id: Ia79bcebbe3ba36f479cbb24dbbb163a031d9c099
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13031
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
This just updates existing guard name comments on the header files
to match the actual #define name.
As a side effect, if there was no newline at the end of these files,
one was added.
Change-Id: Ia2cd8057f2b1ceb0fa1b946e85e0c16a327a04d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12900
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Count DIMMs on current memory channel instead of all memory channels.
The current code is only able to correctly handle the following memory
configurations:
One DIMM installed in either channel.
Four DIMMs installed, two in each channel.
Two DIMMs installed, both in the same channel.
For systems that have any other configuration the DRAM On-Die-Termination
setting is wrong.
For example:
Two DIMMs installed, one in each channel.
Test system:
* Gigabyte GA-B75M-D3H (Intel Pentium CPU G2130)
Change-Id: I0e8e1a47a2c33a326926c6aac1ec4d8ffaf57bb6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12892
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Register settings are the same as on newer chips (compare sandy-
bridge), just at different locations.
Change-Id: Iea0359165074298a376e0e2ca8f37f71b83ac335
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Skip everything but the final setting of PP_CONTROL, i.e. triggering
the power up. The settings with PANEL_UNLOCK_REGS are useless as no
lockable registers were touched in between. Also the loop waiting for
the panel power up to finish was a no-op as the registers with the
power timings were never filled (see follow-up commits).
Change-Id: Ife27dcafdf197b2246c4e69f2bf7a3a6765d1d82
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Don't redefine D0F0_PCIEXBAR_LO, use the #define in x4x.h
- Move TPMBASE and TPM32() definitions into iomap.h
- Use "" style include for x4x.h in nortbridge files.
- Move includes of .h files out of x4x.h and into the c files that need
them.
- Protect function definitions in bootblock.
Change-Id: I3fdb579235c5446733a0ffba05fffe1a73381251
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12849
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make the low-power and small form factor (SFF) options overridable
from romstage main. Also disable both options by default. That's ok
as there aren't yet any in-tree users of the GS45 chipset. As a nice
side-effect, this adds X200s support to the lenovo/x200 port.
Change-Id: I94373851262e6d424cf4885ceca7260c31bc9f61
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/12814
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Passes memtest86+ with either one or two sticks of 2GB ram
but memory map needs a hole at 0xa0000000 to 0xc0000000
Change-Id: Ib34d862cb48b49c054a505fffcba1c17aeb39436
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11307
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Boots to console on Gigabyte GA-G41M-ES2L
Ram initialization *not* included in this patch
VGA native init works on analog connector
Change-Id: I5262f73fd03d5e5c12e9f11d027bdfbbf0ddde82
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/11305
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The remainder of the divide operation was being placed into a Local,
but was never being used, causing an IASL warning. Since this
field is optional, just remove the Local.
Fixes IASL warning:
dsdt.aml 640:Divide (Multiply (CTDN, 125), 100, Local0, PL2V)
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: I0b43ef638b1bc3e1163c45f31f8da57aa0d39e22
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12706
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
The ALIGN_CURRENT macro relied on a local variable name
as well as being defined in numerous compilation units.
Replace those instances with an acpi_align_current()
inline function.
Change-Id: Iab453f2eda1addefad8a1c37d265f917bd803202
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12707
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In coreboot, bool, hex, and int type symbols are ALWAYS defined.
Change-Id: I58a36b37075988bb5ff67ac692c7d93c145b0dbc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12560
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Does native ram init for Intel Atom D5xx 8086:a000 northbridge
Tested on Intel D510MO mainboard, board boots linux kernel
- Works fully with both dimms populated (2x2GB), memtest passes 100%
- Almost boots with only one dimm in one of the slots
(suspect bad memory map with one dimm?)
- Reads garbage with only one dimm in other slot
Change-Id: Ibd22be2a959045e0a83aae2a3a0e877013f80711
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12501
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Based on i945. Tested on Intel D510MO mainboard,
board boots to UART console with this code.
Change-Id: I1d92a1aa6d6d767bda8379807dc26b50b9de75c9
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/10073
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Found while doing code review.
Use a function to toggle IO reset signal.
Change-Id: I4cb0885ed9be763fbc4069e4d015a36a7183c823
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: http://review.coreboot.org/11916
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix regression introduced by:
3660c0fc65
"northbridge/intel/sandybridge: Enable PEG clock-gating on demand"
Issue observed:
GNU/Linux kernel crashes in earlyinit on systems without PEG devices.
The crash occurs on every boot in different functions.
There's no problem on systems with PEG enabled.
Test system:
* Lenovo T530
* Intel Core i5-3320M CPU
* Fedora GNU/Linux 4.1
* PEG disabled in devicetree
Problem description:
Tests shows that modifing PEG chicken bit or device enable bits
after setting BIOS_RESET_CPL causes random crashes in GNU/Linux.
Problem solution:
Disable PEG devices before setting BIOS_RESET_CPL.
Final testing results:
No more random kernel crashes.
Change-Id: I4a967c2d00d7d1e4426cf5abdd5f616c21557da7
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: http://review.coreboot.org/12112
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Issue observed:
Coreboot stops at: "Not enough MTRRs available!"
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
* ATI Radeon HD4780
Problem description:
In case the IGD does not claim VGA decode, the code path taken results
in an integer overflow as uma_memory_base isn't initialized.
The MTRR assignment will fail, because of invalid memory regions.
Problem solution:
Properly initialize uma_memory_base to prevent possible integer overflow.
Final testing results:
The system boots again with IGD not claiming VGA decode.
Change-Id: I025be23b1defb6155469a3eee66569e49a695e7f
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: http://review.coreboot.org/11918
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Issue observed:
Intel raminit works in about 50% of all test-cases on lenovo x220.
Problem solution:
Prefer a smaller valid value over the measured one for
initial timB timings.
Final testing result:
Tests on x220 shows that the issue was resolved.
The test system booted successfully ten times in a row.
Tests on Gigabyte GA-B75M-D3H revealed no regressions.
Test system:
* Intel Pentium CPU G2130
* Gigabyte GA-B75M-D3H
* DIMM: "Crucial 2GB 256Mx64 CT2566aBA160BJ"
Change-Id: I1a115a45d5febf351d89721ece79eaf43f7ee8a0
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11248
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
The Intel northbridge must be paired with a southbridge. Add
the ii89xx southbridge header based on the config setting.
Change-Id: Ied708006310efaba31afe6977ab7e57fe4e5ceec
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12167
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The touched workaround for Sandy Bridge reserves two memory regions that
could cause graphics corruption if mapped by the integrated graphics
device. To the best of our knowledge, the workaround is not needed for
Ivy Bridge revisions.
Tested on kontron/ktqm77 (Ivy Bridge): Booted Linux and checked the
memory regions are not reserved. Couldn't test on Sandy Bridge, due to
lack of hardware.
Change-Id: I4273d1d804b490cf93c23426782eb1ffaf29f7d4
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12326
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Tested-by: build bot (Jenkins)
Add a DMAR table to advertise IOMMU and IRQ remapping capabilities to
the OS.
Tested with kontron/ktqm77. Under Linux, the table is detected and
interrupt remapping is enabled automatically.
Change-Id: Id6ee601a0a8543ed09c6bb8d308a3a3549fc34e5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12195
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Sandy Bridge and Ivy Bridge processors have two IOMMU units. One for the
integrated graphics controller and one for all other PCI devices. Assign
resources for both IOMMUs and apply some quirks.
Tested with kontron/ktqm77 and a Muen based system that makes use of the
IOMMUs. Not tested on Sandy Bridge, but register dumps show the same
settings that are applied here.
Change-Id: I43b5e20b750e7529f448acac35de173185678fd9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12194
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add a parameter to acpi_create_dmar() for the flags field and define
flags given by the spec [1].
[1] Intel Virtualization Technology for Directed I/O
Architecture Specification
Document-Number: D51397
Change-Id: I03ae32f13bb0061bd3b9bef607db175d9b0bc5e1
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12191
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All boards using it have been deleted a long time ago.
Change-Id: Ib1c4018ab6ec27868c0e2fdbf9c91323ead076fb
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12236
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Issue observed:
In a multi GPU setup (IGD and PEG) the system still uses the IGD.
CONFIG_ONBOARD_VGA_IS_PRIMARY has no effect on Sandy/Ivy Bridge.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
* ATI Radeon HD4780
Problem description:
The GMA is missing a disable function.
Problem solution:
Add a GMA disable function. Deactivate PCI device until remaining multi
GPU issues are resolved. Do not claim VGA decode any more.
Final testing results:
The system is able to boot using the PEG device as primary VGA
device.
Change-Id: I52af32df41ca22f808b119f3a4099849c74068b3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: http://review.coreboot.org/11919
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
On Broadwell, this reduces the number of 'remarks' in the IASL build
from 222 to 3.
Fixes these remarks:
Object is not referenced (Name is within method [_CRS])
The ACPI compiler is trying to be helpful in letting us know
that we're not using various fields in the MCRS ResourceTemplate
when we define it inside of the _CRS method. Since we're not
intending to use those objects in the method, it shouldn't be an
issue, but the warning is annoying and can mask real issues.
Moving the creation of the MCRS object to outside of the CRS
method and referencing it from there solves this problem.
This change was made for fsp_baytrail in commit 2eaa0d49
fsp_baytrail: Fix ACPI 'Object is not referenced' warnings
Change-Id: I67a1faf963d1868f4133c7747a43a511cd28a44b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We use UNDERSCORE_CASE. For the MTRR macros that refer to an MSR,
we also remove the _MSR suffix, as they are, by definition, MSRs.
Change-Id: Id4483a75d62cf1b478a9105ee98a8f55140ce0ef
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11761
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This chip is still being used and should not have been deleted. It's
a current intel chip, and doesn't even require an ME binary.
This reverts commit 959478a763.
Change-Id: I78594871f87af6e882a245077b59727e15f8021a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11860
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Consolidate some common (and mostly broken) code. Will try to fix things
in separate commits.
Maybe, igd.asl taken from gm45 (the non-PCH case) could also be used for
i945 and sch. But this needs further investigation.
Change-Id: Id3663bf588458e1e71920b96a3149f96947921e9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11702
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Tested-by: build bot (Jenkins)
Only one value would work with corresponding gma code currently (which one
depends on board). Going forward, it's possible to compute which number can
be used, so there is no need to keep this info around.
Change-Id: Iadc77ef94b02f892860e3ae8d70a0a792758565d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/11862
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Based on the info by Felix Held.
Change-Id: Iab84dd8a0e3c942da20a6e21db5510e4ad16cadd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/11857
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Make sure edge write test results are sane.
Check rn.all to make sure rn.start and rn.end are valid.
Most likely the following test is going to fail on the same
rank anyway.
Change-Id: Ifa601406e6c74ceb8d70063be5ce1bf6bc512c18
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11247
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Don't disable PEG bits while turning on IGD.
Fixes PCI device enumeration of PEG devices.
Test system:
* Intel Pentium CPU G2130
* Gigabyte GA-B75M-D3H
Sidenote: This should be taken from a CMOS option instead.
Change-Id: I2d6522504e4404f2d57f9c319351d08317aefdcb
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11058
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Activate PEG clock-gating only if all PEG devices are disabled.
Fixes system hang when trying to access PEG registers.
Test system:
* Intel Pentium CPU G2130
* Gigabyte GA-B75M-D3H
Change-Id: I7d62fbb83c16741965639cea1a0e4978d4e3d6da
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11059
Tested-by: build bot (Jenkins)
Building an image for the Lenovo X201 with native graphics
initialization selected fails due to the changes introduced by commit
a3b898aa (edid: Clean-up the edid struct).
Same as in 11738 / 11585 / 11491
Change-Id: I4233a4ce2f5423c7ebdad68e8059cd34ac61cfaa
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/11787
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
mohonpeak is the reference board for Rangeley. I doubt anyone uses it
or cares about it. We jokingly refer to it as "Moron Peak". It's code
with no known users, so we shouldn't be hauling it around for the
eventuality that someone might use it in the future.
Change-Id: Id3c9fc39e1b98707d96a95f2a914de6bbb31c615
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11790
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
We already have two other code paths for this silicon. Maintaining the
FSP path as well doesn't make much sense. There was only one board to
use this code, and it's a reference board that I doubt anyone still
owns or uses.
Change-Id: I4fcfa6c56448416624fd26418df19b354eb72f39
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11789
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
This is a sad story. We have three different code paths for
sandybridge and ivybridge: proper native path, google MRC path, and,
everyone's favorite: Intel FSP path. For the purpose of this patch,
the FSP path lives in its own little world, and doesn't concern us.
Since MRC was first, when native files and variables were added, they
were suffixed with "_native" to separate them from the existing code.
This can cause confusion, as the suffix might make the native files
seem parasitical.
This has been bothering me for many months. MRC should be the
parasitical path, especially since we fully support native init, and
it works more reliably, on a wider range of hardware. There have been
a few board ports that never made it to coreboot.org because MRC would
hang.
gigabyte/ga-b75m-d3h is a prime example: it did not work with MRC, so
the effort was abandoned at first. Once the native path became
available, the effort was restarted and the board is now supported.
In honor of the hackers and pioneers who made the native code
possible, rename things so that their effort is the first class
citizen.
Change-Id: Ic86cee5e00bf7f598716d3d15d1ea81ca673932f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11788
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Building an image for the Lenovo X200 with native graphics
initialization selected fails due to the changes introduced
by commit a3b898aa (edid: Clean-up the edid struct).
Change-Id: Ifd36571c9c00761b4a2a6deb3c9c4a52d9d13e25
Signed-off-by: Audrey Pearson <apearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11738
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
While the romstage code flow is not consistent across all
mainboards/chipsets there is only one way of running ramstage
from romstage -- run_ramstage(). Move the
timestamp_add_now(TS_END_ROMSTAGE) to be within run_ramstage().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados. TS_END_ROMSTAGE still present in
timestamp table.
Change-Id: I4b584e274ce2107e83ca6425491fdc71a138e82c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11700
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We don't build-test with native VGA init, so if the code is broken by
a commit, we won't see it when it's guarded by #ifdefs. This has
already happened in the past. Instead of gurading entire files, use
the IS_ENABLED() macro, and return early. This at least enables us to
build-test the code to some extent, while linker garbage collection
will removed unused parts.
BONUS: Indenting some blocks also makes the difference between
framebuffer init and textmode init clearer.
Change-Id: I334cdee214872f967ae090170d61a0e4951c6b35
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11586
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Native VGA init no longer compiles from commit:
* 7dbf9c6 edid: Use edid_mode struct to reduce redundancy
Tested on a single X60 machine.
This patch basically copies 11491 which does
the same for north/intel/sandybridge.
Change-Id: I0663f3b423624c67c2388a9cc44ec41f370f4a17
Signed-off-by: Axel Holewa <mono-for-coreboot@donderklumpen.de>
Reviewed-on: http://review.coreboot.org/11585
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Native VGA init no longer compiles from commit:
* 7dbf9c6 edid: Use edid_mode struct to reduce redundancy
Change-Id: I51a4f4874ce77178cab96651eb7caf2edd862aa2
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11491
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The reason for hardcoding the position of the MRC cache was to satisfy
the alignment to the erase size of the flash chip. Hardcoding is no
longer needed, as we can specify alignment directly. In the long term,
the MRC cache will have to move to FMAP, but for now, we reduce
fragmentation in CBFS.
Note that soc/intel/common hardcoding of mrc.cache is not removed, as
the mrc cache implementation there does not use CBFS to find the cache
region, and needs a hardcoded address.
Change-Id: I5b9fc1ba58bb484c7b5f687368172d9ebe625bfd
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The BOOT_STATE_INIT_ENTRY macro can only be used in ramstage, however
the current state of the header meant bad build errors in non-ramstage.
Therefore, people had to #ifdef in the source. Remove that requirement.
Change-Id: I8755fc68bbaca6b72fbe8b4db4bcc1ccb35622bd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11492
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
When building up which files to include in romstage there
were both 'cpu_incs' and 'cpu_incs-y' which were used to
generate crt0.S. Remove the former to settle on cpu_incs-y
as the way to be included.
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built rambi. No include file changes.
Change-Id: I8dc0631f8253c21c670f2f02928225ed5b869ce6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In the gm45 code, IOMMU is always selected to be enabled. Instead
this patch removes the Kconfig symbol and its dependencies. This leads
to the same effect without the need for the symbol.
The symbol is still used in the K8 code as it's not selected, simply
defaulted to being enabled, and one of the mainboards disables it.
Change-Id: Ibc5939cd1e297d497bf71b1787d852f7cc09a551
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11345
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This replaces various timing mode parameters parameters with
an edid_mode struct within the edid struct.
BUG=none
BRANCH=firmware-veyron
TEST=built and booted on Mickey, saw display come up, also
compiled for link,falco,peppy,rambi,nyan_big,rush,smaug
[pg: extended to also cover peach_pit, daisy and lenovo/t530]
Change-Id: Icd0d67bfd3c422be087976261806b9525b2b9c7e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Original-Commit-Id: abcbf25c81b25fadf71cae106e01b3e36391f5e9
Original-Change-Id: I1bfba5b06a708d042286db56b37f67302f61fff6
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/289964
Original-Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11388
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Kconfig symbol CACHE_MRC_BIN was getting forced enabled everywhere
it existed.
Remove the Kconfig symbol and get rid of the #if statements
surrounding the code.
This fixes the Kconfig warning for Haswell & Broadwell chips:
warning: (NORTHBRIDGE_INTEL_HASWELL &&
NORTHBRIDGE_INTEL_SANDYBRIDGE &&
NORTHBRIDGE_INTEL_SANDYBRIDGE_NATIVE &&
NORTHBRIDGE_INTEL_IVYBRIDGE &&
NORTHBRIDGE_INTEL_IVYBRIDGE_NATIVE &&
CPU_SPECIFIC_OPTIONS) selects CACHE_MRC_BIN
which has unmet direct dependencies
(CPU_INTEL_SOCKET_RPGA988B || CPU_INTEL_SOCKET_RPGA989)
Change-Id: Ie0f0726e3d6f217e2cb3be73034405081ce0735a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11270
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
