With the current timeout of 1000 cycles of 100 microsecond would see
timeout occurs on OCP Delta Lake if the log level is set to values
smaller than 8. Because the prink(BIOS_SPEW, ..) in ipmi_kcs_status()
creates delay and avoid the problem, but after setting the log level
to 4 we see some timeout occurs.
The unit is millisecond and the default value is set to 5000 according
to IPMI spec v2.0 rev 1.1 Sec. 9.15, a five-second timeout or greater
is recommended.
Tested=On OCP Delta Lake, with log level 4 cannot observe timeout
occurs.
Change-Id: I42ede1d9200bb5d0dbb455d2ff66e2816f10e86b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45103
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new memory.c to support DDR4 memory types.
Use the new meminit_ddr() and variant_memory_sku() for eldrid variant
code on memory.c
The initial settings override the baseboard from volteer and fine tune
gpio.c and overridetree.cb on eldrid's configuration.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that Eldrid
can boots. NOTE that tests the ddr4 side of the implementation.
Change-Id: I2c7b30093a8d85bac5aba5b83768af5eb36c4f70
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Allows the AM335X to boot from the coreboot generated MLO by:
- Fixing the load address in the MLO header to be the start of SRAM
- Fixing the way that the bootblock size is calculated (which is
embedded into the MLO so that the MLO knows how much to load into
SRAM). The previous method relied on parsing cbfstool output - the
output has changed format since this was originally written so this no
longer works. Directly using the filesize of the built binary is
probably a more stable way of doing this.
As part of this, the start addresses of SRAM and DRAM were fixed to be
consistent with the AM335x Technical Reference Manual (spruh73, rev Q).
TEST: Booted Beaglebone Black from MLO placed at offset 0x00 on an SD card
Change-Id: I514d7cda65ddcbf27e78286dc6857c9e81ce6f9e
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44381
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The console is initialized before mainboard_init, so the peripheral
should be initialized in bootblock_mainboard_early_init rather than
bootblock_mainboard_init.
Change-Id: I9f4ba29798eb0b1efea76f5ade4a234fb35a2f83
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This is an intermediate step to have SOC_INTEL_COMMON_BLOCK_CPU select
CPU_INTEL_COMMON directly, to avoid dependency problems.
Tested with BUILD_TIMELESS=1: Without including the config file in the
coreboot.rom, both OCP Tioga Pass and Delta Lake remain identical.
Change-Id: I565e75869be730e7c2fe7114b829941bc9890e6c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45041
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This ports Linux commit 71f677a91046599ece96ebab21df956ce909c456
"Handle configuration without P2A bridge".
Quote:
The ast driver configures a window to enable access into BMC
memory space in order to read some configuration registers.
If this window is disabled, which it can be from the BMC side,
the ast driver can't function.
Closing this window is a necessity for security if a machine's
host side and BMC side are controlled by different parties;
i.e. a cloud provider offering machines "bare metal".
P2A stands for primary to AHB.
Tested on Prodrive Hermes, which uses an AST2500. The machine still
boots, has a high resolution framebuffer working in EDK2, and its
boot time has been reduced by 2.5 seconds as it no longer runs into
a timeout due to disabled P2A bridge.
Change-Id: I3293dc35ae89c010154e02eff904ec3a68c96683
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fixes complains about missing INT configuration by the pciexp kernel
modules.
Tested with Linux 5.5 on Prodrive Hermes.
Change-Id: I277f592cd8d2c86a9c7ba4b34d3f703f7d593582
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The three Intel Apollo Lake boards (apl_rvp, leafhill and minnow3) do
not define MAX_CPUS, which would then default to 1. Since this is most
likely an oversight, use the same value as other Apollo Lake boards.
To ensure this does not happen again, factor out MAX_CPUS to SoC scope.
Change-Id: I5ed98a6b592c8010b59eca7ff773ae1ccc4cd7b1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APL does not support Hyper-Threading, and has at most four CPU cores.
Change-Id: Ib2ffadc0c31cdd96bec8eed5364c984acb2e1250
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45143
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update critical and passive policy for TSR0.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I244e1b5cacabf5b73c47b4039ae150cd17fcd0fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45169
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sushi is not a real product, just a test of the new_variant program.
The effort to keep it up-to-date with the rest of Hatch is no longer
worth it. Remove the variant.
BUG=b:168030592
TEST=build bot is successful, hatch-cq builds successfully
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I2b0036f3cbdea4bfaed1274ab87a20d24c75de57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CB:44774 introduced the non-existent SPD path. This is preventing the
device from booting up.
BUG=b:168053219
TEST=Build and boot drawcia board to OS.
Change-Id: I70ca5f4cf2c8e2e88ea5b1514b656caafb732743
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SMBus code is linked unconditionally since commit 0e3c59e. This change
drops that obsolete part from the help text.
Change-Id: I603ab012760684021be1b5eca5d0ddff69463b79
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Most of them are needed for SMBIOS type 17 creation.
Tested=With FSP WW36 verified the printed hob values match
with FSP hob data.
Change-Id: I02f4600f1be39e2576d7c84a5a6b6672ebb7034b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44847
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Support SPI flash dual read funciton which change spi mode (1-1-1)
to dual mode (1-1-2).
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: Iabd3668fc4bc42137b7743144fc1cced4fe72737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44852
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To minimize the quirks the kernel has to apply, the headset mic is set
to its correct value in coreboot.
Tested on lemp9, audio is functional.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I6b59de95f01360a5f7779f87f39edeb75dedc215
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43631
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSTACK2 (IOU3) should be stack number 4, mainboard uses stack number as
the index to access the bus number array read by get_stack_busnos().
Without the fix it would get the wrong bus number (0xb1).
Tested=On OCP Delta Lake, dmidecode -t 9 to verify slots bus number on
IOU3 are correct (0xb2).
Change-Id: I1c9e49bbc9a00de82d1fc67b3b4ed47e03eacdda
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:162232776
TEST=Measured the I2C bus frequency as 389 KHz, high time as 870 ns and
low time as 1580 ns.
Change-Id: I67d2725a7fc8d83e3fa8a56cfa86540c4e6f0971
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45084
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:163743035
TEST=Measured the I2C bus frequency as 384 KHz, high time as 924 ns and
low time as 1680 ns.
Change-Id: I60a5f6814fb9818c724f6b6fe465ea49d0de0f97
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45083
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP v3333 or later, provides a new UPD to Skip configuring
GPIO settings from FSP. coreboot should provide all the
required GPIO configuration for the platform when this UPD
is set.
BUG=b:166790597, b:146390704
BRANCH=none
TEST=build and boot volteer proto2
Cq-Depend:chromium-internal:3240396,chromium-internal:2870145
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: If32f35a188d510db8e4d8973cae78297d49a9240
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44913
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update FSP headers for Tiger Lake platform generated based FSP
version 3333. Previous version was 3313.
Changes Include:
1. Update comments
2. Add new UPD for Gpio Override support
BUG=b:166790597
BRANCH=none
TEST=build and boot volteer proto2
Cq-Depend:chromium-internal:3240396,chromium-internal:2870145
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie3f0688143eef532946c7a2141909c1ac173fc2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44912
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Rename from jasperlake to elkhartlake
2. Remove irelevant devices asls (ipu,ish,camera clock,gpio_op)
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I5e77081d1673cc0ca97edc63e9996c045ab6e9b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44812
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Replace "jsp" with "mcc"
4. Rename structure based on Jasperlake with Elkhartlake
5. Clean up upd override in fsp_params.c will be added later
6. Sort #include files alphabetically as per comment
7. Remove doc details from espi.c until it is ready
8. Remove pch_isclk & camera clocks related codes
9. Add new #define NMI_STS_CNT & NMI_EN as per comment
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I372b0bb5912e013445ed8df7c58d0a9ee9a7cf35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Unlike other platforms, Apollo and Gemini Lake have VmxEnable on FSP-S.
Note that this will enable VMX by default on both of these platforms.
Change-Id: I6a4470e0e64b10f07edfcf270bb02c7cd6a8fa1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This is an intermediate step to have SOC_INTEL_COMMON_BLOCK_CPU select
CPU_INTEL_COMMON directly, to avoid dependency problems.
Tested with BUILD_TIMELESS=1, UP Squared does not change.
Gemini Lake already selects this through SOC_INTEL_COMMON_BLOCK_SGX.
Change-Id: If737fa6d8700f435c8692c80244f0e71657c2236
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
The PRM does not describe the relevant bits, but Linux's i915 driver
handles these bits the same way for both Ironlake and Sandy Bridge.
Change-Id: Ice7412e335752bd7e297ad50f685effcefbd41d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All boards currently have backlight on either LVDS or eDP.
Change-Id: I878bc7f1ff75a2b82b9556e855aff1d4d03e0268
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Configure eldrid to use CSE Lite.
BUG=b:158140797
TEST=cd to volteer's asset_generation folder, execute
"./gen_all_variant_images.sh" and verify that all variant
images are produced.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I357abdac4102f358d3aa1cb50f600312039ef140
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The SMRR MSRs can be locked, so that a further write to them will cause
a #GP. This patch adds that functionality, but since the MSR is a
core-level register, it must only be done once per core; if the SoC has
hyperthreading enabled, then attempting to write the SMRR Lock bit on
the primary thread will cause a #GP when the secondary (sibling) thread
attempts to also write to this MSR.
BUG=b:164489598
TEST=Boot into OS, verify using `iotools rdmsr` that all threads have
the Lock bit set.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4ae7c7f703bdf090144637d071eb810617d9e309
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The IA32_MTRR_CAP register has a bit which indicates that the SMRR MSRs
can be "locked" and this patch adds the definition for that.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1254fb40c790f2a83dd11c2aabcf9bdf922b9395
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The IA32_SMRR_PHYS_MASK MSR contains a 'Lock' bit, which will cause the
core to generate a #GP if the SMRR_BASE or SMRR_MASK registers are
written to after the Lock bit is set; this is helpful with securing SMM.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I784d1d1abec0a0fe0ee267118d084ac594a51647
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For Volteer (and future Tiger Lake boards) we can enable mode S0i3.4
only if we know that the Cr50 is generating 100us interrupt pulses.
We have to do so, because the SoC is not guaranteed to detect pulses
shorter than 100us in S0i3.4 substate.
A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code
running in verstage, which will program a new Cr50 register, provided
that Cr50 firmware is new enough to support the register.
This CL adds code to detect the case when Cr50 is unable to generate
longer pulses, and in that case explicitly disable the S0i3.4 substate
as well as setting gpio_pm_override to all zeroes. This will increase
power usage slightly, but guarantee that the GPIO block in the SoC
does not switch to a slower sampling clock. In practice, this case
will only be encountered in the factory, before the Cr50 chip is
updated to a new RW image.
(Prior to this change, the gpio_pm_override was hardcoded to zero for
Volteer, but the S0i3.4 substate was not disabled. According to my
conversations with Intel engineers, that was not enough to guarantee
detection pulses shorter than 100us. But it is entirely possible that
we have just been "lucky" that the SoC has not gone into low power
mode during the boot process, where most of the cr50 communication
happens.)
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
BUG=b:154333137
Change-Id: Idef1fffd410a345678da4b3c8aea46ac74a01470
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add DTT (Dynamic Tuning Technology) support for Jasper Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=Noe
TEST=Build and boot on jslrvp board
Change-Id: I41409c70d8472c54ca452fc98d5ee9edf3ccd307
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the dooly variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.2).
BUG=b:155261464
BRANCH=puff
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_DOOLY
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Change-Id: I8e714cc9bf4a49266da77db88f8c4a3ca45878d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
3.6 schematic will separate TS power from eDP PP3300 to GPIO
for power control and correct GPIO assignment from GPIO_90 to
GPIO_32 instead.
BUG=b:161579679
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Ieef67e1d04201c5d9e1dc625c519e6d0307c55f0
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds support for line-buffered console output to System76 EC firmware.
Once the print command is received, the EC firmware multiplexes the output
to any enabled console on the EC. This can be a memory ringbuffer, a
parallel port (using the keyboard connector), or i2c (using the battery
connector). Once the entire buffer is sent, it sets the command register
to 0, indicating completion. For more information, please see:
https://github.com/system76/ec/blob/master/doc/debugging.md
Tested on system76/lemp9 with CONSOLE_SYSTEM76_EC enabled.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I861bf3e22f40dd6c3ec7ba1d73711b399358e332
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
On autogenerated FMAPs, there's no `UNIFIED_MRC_CACHE` region. The
current code will print a spurious error message about it, though.
Reduce the log level to BIOS_INFO to avoid confusion.
Change-Id: I0961bb2a7d2d81dc5c0d28f6e6c29b320421fc3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45076
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable SataPortsDevSlp for SATA ports 2 and 3.
Change-Id: Id6c69f4a6fe45cb5c6aad3f42c741a2724c6166c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Enable the I2C HID driver, configure I2C bus 0 and add the touchpad
device to the devicetree.
Tested on lemp9, touchpad confirmed to use i2c-hid driver in Linux
instead of PS/2.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ic3a90fda134b1d53f28ab687b3033ec52fee843b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43623
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
_GPE cannot be anywhere but at the root of the ACPI namespace.
This change ensures that is always the case.
Tested on lemp9, GPE still in correct location.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib31683b06e61da4b1859cd939c36879cebf4c03c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43630
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs required for DeepSx (e.g. SLP_SUS#) are not hooked up on the
lemp9. Therefore, drop the DeepSx settings.
Tested on lemp9, suspend works correctly.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Iab179abd7adc3a65dcfc43ce1b5742d514b711fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43629
Reviewed-by: Michael Niewöhner
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested on lemp9, SA thermal device appears in lspci.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I527e586b1dae5f8087d2364c63c9db5bcb643214
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Fsp configures the USB over-current pin and overrides the according pad
configuration to NF1, regardless of the port being configured as disabled.
Thus, set the OC pin to 0xff ("disabled") in this case to prevent this.
This allows us to skip setting USBx_PORT_EMPTY in the devicetree for
disabled USB ports.
Change-Id: Ib8ea2ea26c0623d4db910e487b37255e907b299d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45112
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Add required SoC programming till bootblock
2. Include only required headers into include/soc
3. Add CPU/PCH/SA EDS document number and chapter number
4. Include ADL-P related DID, BDF
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I204e692fabb84fce297bebee465f4ca624c6fe56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Don't configure USB3 port 4 since it's not used.
Change-Id: I6919f5ec3a5be53373f2ab75063764287b53baf5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner
Currently HECI3 gets enabled by the option Heci3Enabled, but this
duplicates the devicetree on/off options. Therefore depend on the
devicetree for enablement of the HECI3 controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Heci3Enabled setting, and divergent
devicetrees were adjusted.
Change-Id: Ic7d52096aee225c2ced1e1bc29ca850fe5073edc
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44579
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previous CL (1916f8969b) misinterpreted
spec as requiring size alignment on all IVHD device entries. The correct
requirement specifies only for 4-byte entries. The unneeded realignments
result in gaps in the table. The kernel hangs in early boot due to the
malformed table.
Remove 8-byte entry alignment.
BUG=b:166519072
TEST=Boot fully to morphius board with and without amd_iommu kernel
parameter. Confirm IVRS contains no alignment gaps/corruption.
Change-Id: Iddcff98279be1d910936b13391dd2448a3bb2d74
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
ddr_frequency is ambiguous and is interpreted differently in several
places. Instead of renaming this field, this deprecates it and adds
two new fields with unambiguous naming, max_speed_mts and
configured_speed_mts. smbios.c falls back to using ddr_frequency
when either of these fields are 0.
The same value was being used for both configured memory speed and
max memory speed in SMBIOS type 17, which is not accurate when
configured speed is not the max speed.
BUG=b:167218112
TEST=Boot ezkinil, no change to dmidecode -t17
Change-Id: Iaa75401f9fc33642dbdce6c69bd9b20f96d1cc25
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44549
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To allow using the 3 remaining Comet Lake SoCs, add a new Kconfig option
for each of them and configure the paths to FSP header files and FSP
binary.
Change-Id: I4272a6ee08e19769a8a17c93bb3ce2421be0bbc9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Michael Niewöhner
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GPP_F14 should be configured to be routed via APIC and not SCI.
BUG=b:162528549
TEST=verified on a volteer
Change-Id: Ie262ceeaea1c07bcc99e1545f5eb99e0d0dee905
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PSP bootloader and verstage are only used out of the RO region,
so don't build them into the RW sections.
BUG=None
TEST=Build & Boot
BRANCH=zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ic7bcb9a6a78926325e80755c010bb047e4a9485c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
This allows a platform to specify the location of the signing token
for the PSP verstage, and build it into the firmware image.
BUG=b:166108929
TEST=Build file into PSP firmware, verify that it's present and has
the correct ID.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I182ad9b48a2776ccd29ead0f54cfe14c5bf45560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
To use a signed PSP verstage, we're going to need to build it first,
then sign and store the binary. This patch allows the stored (signed)
verstage binary to be used.
BUG=b:166108929
TEST=Build with existing verstage binary instead of re-building it.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5cbceca3b75f05c5460190b1c829d1ffaab2c736
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Move PSP_SHAREDMEM_DRAM_END after _etransfer_buffer to ensure that the
transfer buffer actually lives within the 32KiB that is supported to be
transferred. Resulting symbol address change in bootblock.debug file
summarized below.
BEFORE:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02019000 T _epsp_sharedmem_dram
02019000 T _preram_cbmem_console
0201a600 T _epreram_cbmem_console
0201a600 T _timestamp
0201a800 T _etimestamp
0201a800 T _fmap_cache
0201ac52 T _efmap_cache
0201ac52 T _etransfer_buffer
AFTER:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02014040 T _preram_cbmem_console
02015640 T _epreram_cbmem_console
02015640 T _timestamp
02015840 T _etimestamp
02015840 T _fmap_cache
02015c92 T _efmap_cache
02015c92 T _etransfer_buffer
02019000 T _epsp_sharedmem_dram
BUG=b:167243965
BRANCH=None
TEST=checked 'cbmem -1' for FMAP error after ec reboot
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I9b482aced5deb40bd87d19d9c42585d8a6db5fc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45045
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Trogdor variants power their USB hub from a PMIC LDO that is
already enabled by QcLib, and some have a discrete LDO that is
controlled by GPIO_84. For the latter, let's make sure we assert that
GPIO on boot.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9d206cd7154ded3bf179e68c2b1421d0a8ee89f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
We're moving a lot of pins around on Trogdor again. For firmware this
only affects the RAM and SKU strapping ID pins. Since there are quite a
few of the old devices in circulation this time and some people seem to
care about mosys RAM information working, let's actually check the board
revision and support both cases this time.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7728d8ea4b7f6e7ff6721ade90f975f6efd5ddd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Set tcc offset to 5 degree celsius
2. Apply the DPTF parameters receive from the thermal team.
3. Change PL2 min value from 25W to 15W.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I68fdefe99cf36a39797c29ad84d08321bb8175f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This reverts commit 2ad859988b.
Reason for revert: broke the build
Change-Id: I7e7d917c2e8b698d5c7c3ce0b6d34e80696185f3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44993
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add new SPD file, "samsung_dimm_K4E8E324ED-EGCG.spd.hex".
2. Add SPD support in Rammus memory table, as follows:
SPD_SOURCES += samsung_dimm_K4E8E324ED-EGCG # 0b0110
SPD_SOURCES += samsung_dimm_K4E6E304ED-EGCG # 0b0111
BUG=b:166576463
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I82386507c4e996e0a59c26ce50de3bced45b1196
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44854
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BOOTBLOCK_CONSOLE is already set to yes in console/Kconfig file.
Change-Id: I2a4ee517795bc7b378afc5eae92e2799ad36111b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
1. Apply the DPTF parameters receive from the thermal team.
2. Change PL2 min value from 25W to 15W.
3. Change PL2 max value from 64W to 51W.
BUG=b:166696500
BRANCH=puff
TEST=build and verify by thermal team
Change-Id: I53a4e8809369883c3ba77744fdc05fb510408209
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44903
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
BUG=b:158986928
BRANCH=puff
TEST=duffy boots and dumped SSDT table for quick check.
Change-Id: I45987f44ec381917173f8d2a878edb50da454b4b
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO_144 is REPORT_EN pin for the touchscreen controller where 1 means
enable operation and 0 means stop operation. Override tree exposes
this pin as stop GPIO. Thus, it needs to be configured as active low
i.e. 0 = active (stop), 1 = inactive (enable report).
Change-Id: I349123655260349b78d2f75f846da0ce1dc966fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
4. Clean up upd override in fsp_params.c, will be added later
5. Temporarily remove _weak attributes in fsp_param & romstage.c
6. Add required headers into include/soc/ from jasperlake directory
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: If2bbe0b8a12bb78b3650f9d0a60f002f7eacb513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Clone entirely from Jasperlake
This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/36550
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
6. Add required headers into include/soc/ from JSL directory
Elkhart Lake specific changes will follow in subsequent patches.
1. soc/intel/elkhartlake: Update Kconfig
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I9f91c1efa81a358b1f59e032e209e07b62d54613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The BT instruction stores its result in CF and not ZF so use the
correct jump instruction.
This fixes a hang in postcar on CPUs lacking support for this
instruction. This concerns older pre-SSE2 hardware.
Change-Id: I704e3c579150fb9b9a292ef0e83050e7bf7cb078
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Checked with the schematics that all PCIe clocks have a corresponding
clock enable pin.
BUG=b:149970243
BRANCH=zork
Change-Id: If96cdf95e213682217e46a98fc69c5c2ef4a148d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44892
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the general purpose PCIe clock outputs configurable to be either
permanently enabled, permanently disabled or dynamically enabled via
their corresponding external #CLK_REQx pins in the board's devicetree.
BUG=b:149970243
BRANCH=zork
Change-Id: I3f5760c0b869e8a9416ba9b57d182a88a2eb5e44
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The _SHIFT postfix is a bit clearer than the _SHL one and more in line
with the names used for this kind of defines in coreboot. The
documentation on that register is currently wrong and will hopefully be
fixed in the future; the defines should now match the hardware.
BUG=b:149970243
BRANCH=zork
Change-Id: I977f107d466521484ca13fa1f4dd86a50c8150d7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The code using the macro was found not working after finally enabling
the HDA PCI device on the hermes board.
Fix a typo to generate the correct verbs.
Tested on prodrive/hermes.
Change-Id: I953c2e9fbebc1f02bdf71ce868a95f578300c3a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44900
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replacing the existing defines with macros makes them easier to use in a
function that applies the setting for a certain GPP/GFX clock output.
Also add macros for statically enabling or disabling the clock outputs
and not only for configuring them as controlled by the #CLK_REQx pins.
BUG=b:149970243
BRANCH=zork
Change-Id: I14198f224639721fe6ca71ca3dcd9cb413a587d5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On Picasso MISC_CLK_CNTL1 doesn't contain OSCOUT[12]_CLK_OUTPUT_ENB and
this was probably just copied over from stoneyridge.
BUG=b:149970243
BRANCH=zork
Change-Id: I32f459026c4e8632672123681b20736245f198b2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44886
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Linux kernel drivers bind to "DMI quirks." In this case, the audio
fw_config is added as an OEM string, e.g., "AUDIO-MAX98357_ALC5682I_I2S"
so the audio topology can be correctly discovered.
But add all successfully probed fw_config items as well, because this
makes it easier to view what is selected from userspace.
BUG=b:161963281
TEST=With CBI FW_CONFIG field set to 0x201:
localhost ~ # dmidecode -t 11
# dmidecode 3.2
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: DB_USB-USB4_GEN2
String 2: AUDIO-MAX98373_ALC5682I_I2S
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7b7586b0ebfe7b2fd888f448a50ae086364fa718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a backing cache for all successfully probed fw_config fields that
originated as `probe` statements in the devicetree. This allows recall
of the `struct fw_config` which was probed.
BUG=b:161963281
TEST=tested with follower patch
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0d014206a4ee6cc7592e12e704a7708652330eaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPP_F11 was in the early gpio table, but the definition was missing
from the main gpio_table. This change adds GPP_F11 to the gpio_table
array.
BUG=none
TEST="emerge-volteer coreboot" and verify it builds correctly.
Change-Id: I40f887300a9dfd4f8e790031b77bbee8a014f499
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Add Makefile.inc to include six generic DDR4 SPDs for the following
parts for Eldrid:
DRAM Part Name DRAM ID to assign
H5AN8G6NDJR-XNC 0 (0000)
MT40A512M16TB-062E:J 1 (0001)
H5ANAG6NCMR-XNC 2 (0010)
K4A8G165WC-BCWE 0 (0000)
K4AAG165WA-BCWE 3 (0011)
MT40A1G16KD-062E:E 3 (0011)
Add mem_list_variant.txt as a manifest of eldrid's DRAM parts for use
by gen_spd, the generic DD4 SPD generation tool.
Add dram_id_generated.txt to specify DRAM ID strap settings.
NOTE that Eldrid specified DRAM IDs for the first three parts to be 0
though 2 (i.e. no combined DRAM IDs for parts that use the same SPD).
BUG=b:161772961
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
without error.
Change-Id: Ica62e299ed40e60c2d5928b29ead5d2205b1af66
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44272
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This SuperIO chip is used on the Intel DQ45EK mainboard. Restore the
driver that was deleted in commit d3a1a4171e ("src/superio: Remove
unused superio chips"). Changes from the previous version include:
- Replacing the early serial implementation with Winbond common code,
- Replacing the license boilerplate with SPDX headers, and
- Removing unnecessary header file references.
Change-Id: I0ff1a63c47d5dff2599c83a1cebe1ac5ff2136b1
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable TBT2 setting in overridetree.cb based on schematic.
BUG=b:165175296, b:166060548
BRANCH=none
TEST=Check all USB ports USB2 and USB3 both functional
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I23ecf76a3c2f631211b0ae2898707c68862b374b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Set tcc offset to 5 degree celsius for kaisa and duffy
BUG=b:166696500
BRANCH=puff
TEST=Build, and verify test result by thermal team.
Change-Id: I2bb977b98c0764f0b9cac3543074da56057717cf
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44901
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MODEM_CLKREQ / CNVI_CLKREQ has no external pull-down resistor.
When there is no M.2 card populated, the pin is floating. Thus
enable an internal 20K PD.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I37e0a9d7e9e0a8c8a7ac198abfd3995b8b0f9e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Add CNVi and PCIe wifi devices to the devicetree and enable the wifi
driver and SMBIOS tables in Kconfig.
Test: both CNVi and PCIe wifi devices work fine
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I16e04dbbf5fc3a163ce5a2bb8de646877d5cbc0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43654
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rework the comments:
- fix wrong gpio / net names
- convert all comments to <gpio> / <net name>
- add more information where appropriate
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I51b552fd3255d5627dcc012e677bad51be517cf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43650
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
INTP_OUT can be used as Type-C VBUS sense input/interrupt but is
currently unused in coreboot. It isn't a requirement for PD to work.
Disable it for now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I233fbb562969487dff095ba6589fb9da3301ae4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43647
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable internal pull-ups for SATAXPCIE pads since there are external
ones at the M.2 slot's PEDET pins.
Test: both, SATA and NVME devices work fine on both slots
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6be716620695ac38c44a17abe1c4de97b099b8d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43645
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are pads being unused for various reasons:
a) missing board support (DeepSx: SUSWARN#)
b) unneeded feature ID pins
- currently no known device models without keyboard backlight
- currently no known device models without TPM
c) BOARD_ID (L140CU/L140ZU) is fixed and known at build time
d) DDR_TYPE_*: there is only one known ram model
e) strap-only pads
f) unconnected pads
Configure them as NC with appropriate pull-up if no external pull exists.
The latter was checked by schematics and looking at the board.
When any of the unused ID pins is needed in the future, they can be
reactivated easily (configure as GPI).
Further, convert from use of legacy macro PAD_CFG_NC to PAD_NC.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia370c180d5ae6f48360be14af3cbab29e6814e75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43644
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To support CSE Lite firmware update, CSE RW partition is extracted from
CSE blob binary and added to FW_MAIN_A and FW_MAIN_B.
CSE RW size for TGL is close to 2.3MB; hence, the size of FW_MAIN_A and
FW_MAIN_B is increased to avoid an overflow.
BUG=b:140448618
TEST=build with me_rw binary blob for volteer and boot to kernel.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Ie3c2b657f0426d206dfe3729829ec34ff57812c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43790
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
L140CU has a TPM2 connected via SPI. Add the TPM device to the
devicetree and enable it.
According to Intel doc#615170-001, PIRQ is required for SPI TPM to work.
Since the TPM is connected to GPP_A7, enable NF1 (PIRQA#) and set it as
TPM interrupt in Kconfig.
Note: The PCH maps either LPC TPM or SPI TPM to the same address and
handles either LPC or SPI communication transparently. Thus we can use
MAINBOARD_HAS_LPC_TPM here, which implements TPM via that address.
Tested, but only polling works currently, because there is some upstream
issue with the tpm_tis module in current Linux kernels. [1]
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1770021
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I26d3b396fe1e99368e18fd3a6a9f02e3585b9f6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43641
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows calling GETSEC[CAPABILITIES] during early init, when the MSR
isn't locked yet.
Change-Id: I2253b5f2c8401c9aed8e32671eef1727363d00cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This is a security lock and is required for TXT, among other things.
Tested on Asrock B85M Pro4, still boots.
Change-Id: I7b2e8a60ce92cbf523c520be0b365f28413b9624
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44884
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix an issue the assembler didn't warn about to fix a crash on real
hardware. qemu didn't catch this issue either.
The linker uses the same address for variables in BSS if they aren't
initialized in the code. This results in %edx being set to the value
of %eax, which causes an exception restoring IA32_EFER on real
hardware.
Tested on qemu with KVM enabled.
Change-Id: Ie36a88a2a11a6d755f06eff9b119e5b9398c6dec
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
We can now factor out the essentially duplicated ME functions.
We include a .c file to preserve reproducibility. This is needed because
there are two different `mei_base_address` global variables, and we have
to access the same variables in order for builds to be reproducible.
The duplicate global in `me.c` and `me_8.x.c` will be completely gone
once this new `me_common.c` file becomes a standalone compilation unit.
We are wrapping some things in static inline functions, as they won't be
directly accessible anymore after moving to a separate compilation unit.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 remains identical.
Change-Id: I057809aa039d70c4b5fa9c24fbd26c8f52aca736
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
This PCI ID is required in order for the CML devices to perform
SSDT generation for DPTF.
CML Processor, EDS, Vol 1,
Table 9-5, Section 9.2.
BUG=b:158986928
BRANCH=puff
TEST=builds
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Change-Id: I94aea6b9e0f60656827daada7b2cc2741604b8b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Andrew McRae <amcrae@google.com>
Add vb2ex_hwcrypto_rsa_verify_digest function for verifying rsa
signature against digest using PSP svc.
This function will be later used by vboot to accelerate rsa
verification.
BUG=b:163710320, b:161205813
TEST=build zork firmware with vboot modification, confirm it's booting
and boot time is reduced by ~230ms.
Change-Id: Ic5c1d13092db5a84191642444f3df9c26925e475
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44456
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SATA is currently turned on in the Dalboz and Trembyle base board
variant devicetrees, even though no Google/Zork device uses SATA; for
mass storage they either use eMMC or NVME PCIe SSDs. This patch disables
both the SATA PCIe device and the bus where it was the only enabled
device on. The next patch in this patch train sets a new FSP-M UPD
setting
BUG=b:162302027
Change-Id: Ie7773d9dcb0518c3e01bdd0af23b62268ab64694
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44068
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP has recently added support for a UPD switch to power gate SATA. This
change adds the coreboot side of the feature. To avoid having two SATA
enable options, the value of the sata_enable UPD is determined by the
enable state of the AHCI controller in the platform devicetree.
BUG=b:162302027
BRANCH=zork
TEST=Verify AHCI controller can be hidden/disabled.
Change-Id: I48bf94a7e6249db6079a6e3de7456a536d54a242
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44067
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested on OCP Delta Lake, with FSP WW34 DCI can be connected if enabled.
Change-Id: I8e0dff921cef02dfc66467a2b8fa3e196fb36ac2
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Intel CPX-SP FSP ww34 release added some features:
a. change DDR frequency limit.
b. define MRC debug message verbosity level.
c. enable/disablee of PCH DCI.
In addition, there are some changes to HOB data structures.
Update UPD and HOB header files and adapt soc accordingly.
TESTED=booted on YV3 DVT to target OS command line. Also rebooted okay.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Iadbf5dc850c445f988bc7f07a24165abed2298c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44685
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These parts have not been used in any woomax devices. Removing
so IDs can be assigned more efficiently.
Command to generate files:
go build gen_part_id.go
local variant=woomax
./gen_part_id ../../../src/mainboard/google/zork/spd ../../../src/mainboard/google/zork/variants/${variant}/spd/ ../../../src/mainboard/google/zork/variants/${variant}/spd/mem_parts_used.txt
BUG=b:165611555
TEST=none
Change-Id: I651539c2df8e6d817582573d45b9e77156ece7d4
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These parts have not been used in any berknip devices. Removing
so IDs can be assigned more efficiently.
Command to generate files:
go build gen_part_id.go
local variant=berknip
./gen_part_id ../../../src/mainboard/google/zork/spd ../../../src/mainboard/google/zork/variants/${variant}/spd/ ../../../src/mainboard/google/zork/variants/${variant}/spd/mem_parts_used.txt
BUG=b:165611704
TEST=none
Change-Id: I9020fc9cbbb4a97664b0c969dd841c5696a4d60f
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44871
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These parts have not been used in any dirinboz devices. Removing
so IDs can be assigned more efficiently.
Command to generate files:
go build gen_part_id.go
local variant=dirinboz
./gen_part_id ../../../src/mainboard/google/zork/spd ../../../src/mainboard/google/zork/variants/${variant}/spd/ ../../../src/mainboard/google/zork/variants/${variant}/spd/mem_parts_used.txt
BUG=b:165611271
TEST=none
Change-Id: I605550d44ba57d979df1bd5bef114f8ecc94fa3a
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44846
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Switch all zork boards to use generated generic SPDs from spd_tools.
HMAA1GS6CMR6N-VK is unused by Ezkinil, and all other boards, so it was
removed.
picasso/Makefile.inc was updated to populate the 2nd APCB channel based
on APCB_POPULATE_2ND_CHANNEL. This removes the need to suffix spd
entires with _x1/_x2.
Command to generate files:
$ find src/mainboard/google/zork/variants/ -maxdepth 1 -type d | grep -v '/$' | while read b; do
n=$(basename ${b});
if [ "${n}" = "baseboard" ]; then
continue
fi
go run util/spd_tools/ddr4/gen_part_id.go src/mainboard/google/zork/spd \
src/mainboard/google/zork/variants/${n}/spd \
src/mainboard/google/zork/variants/${n}/spd/mem_parts_used.txt
done
BUG=b:162939176
TEST=Boot ezkinil and dalboz check dmidecod -t17
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I0553858f83d3d1e90cf35bece108768f004a29a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44480
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add mem_list_variant.txt, a list of memory parts used by elemi SKUs.
Add dram_id.generated.txt, a list of dram id's to use for each memory part.
Add Makefile.inc, to specify DDR4 and build the SPD file list.
BUG=b:165461530
TEST=none
Change-Id: I6dbcccf577161cc0c787775e2ac03e0c7039baef
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44650
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add memory parts needed by zork boards. Attributes are derived from data
sheets.
BUG=b:162939176
TEST=Compared generated SPDs with data sheets and checked in SPDs
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I67f205f9af24bbc5c12656be1f363a15fe975955
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44447
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If a memory part is a x16 part that has two dies and only a single
rank, then the x16 describes the part width (since this solution will
need to be a stacked solution) and as such, we must translate the
DeviceBusWidth to the "die bus width" instead.
Change DeviceBusWidth variable name to PackageBusWidth to be more
descriptive
BUG=b:166645306, b:160157545
TEST=run gen_spd and verify that spds for parts matching description
above changed appropriately.
Change-Id: Ia6f3ca109d344b7a015da28125a94ce10d2bdfb8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The TS_DONE_LOADING timestamp description had "(ignore for x86)", but
the implementation in vboot_logic.c will read every bytes, so the
timestamp is correct even for devices with memory mapped boot device
(e.g., x86).
To prevent confusion we should remove the 'ignore for x86' message.
BUG=None
TEST=make -j
BRANCH=None
Change-Id: I01d11dd3dd0e65f3a17adf9a472175752c2b62bc
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44800
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I noticed that re-running the lpddr4x SPD parts id tool that generates
the variants/VARIANT_NAME/memory/Makefile.inc changed the SPD that is
used for the H9HCNNNCPMMLXR-NEE part.
$ go run ./util/spd_tools/lp4x/gen_part_id.go \
src/soc/intel/tigerlake/spd src/mainboard/google/volteer/variants/delbin/memory
src/mainboard/google/volteer/variants/delbin/memory/mem_list_variant.txt
Based on the currently checked in generic SPDs for LPDDR4x, this
operation changes the Makefile.inc to use lp4x-spd-3.hex for the
H9HCNNNCPMMLXR-NEE part instead of lp4x-spd-2.hex.
This change updates that discrepancy in Delbin's memory Makefile.inc.
BUG=none
TEST=none
Change-Id: I9a19ab7b1bcdc3814fdd9c462ca2f590c8ed2935
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44785
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a SPI-NOR flash controller which supports pio mode.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I1e38672a532dd8234b3ef24c84113888c8795810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Change lp4x spd names to include lp4x memory type (eg. lp4x-spd-1.hex).
BUG=b:160157545
TEST=run gen_part_id for volteer variants and verify that it changed
spd names to prepend the "lp4x-" to the filename..
Change-Id: I0c59da7eb78f34640aad2e852ca725d3e8571a8e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44784
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that generic SPD files have the memory type prepended to the
filename, they can be stored in the same location. This CL moves
the generic SPDs to the new location.
Change the ddr4 gen_part_id.go and gen_spd.go tools to use
"ddr4_spd_manifest.generated" instead of "spd_manifest.generated".
Change the lpddr4x gen_part_id.go and gen_spd.go tools to use
"lp4x_spd_manifest.generated" instead of "spd_manifest.generated".
Move TGL DDR4 and LPDDR4x generic SPDs into a common location.
Move JSL DDR4 and LPDDR4x generic SPDs into a common location.
Change the volteer/spd/Makefile.inc to use the new path for the spds.
Change the dedede/spd/Makefile.inc to use the new path for the spds.
BUG=b:165854055
TEST="emerge-volteer coreboot" and verify all variants build correctly.
Change-Id: I83b088cb718d15ffd3012c84a12b5231ae84a3e4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44648
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It seems that GCC's LTO doesn't like the way we implement
DECLARE_OPTIONAL_REGION(). This patch changes it so that rather than
having a normal DECLARE_REGION() in <symbols.h> and then an extra
DECLARE_OPTIONAL_REGION() in the C file using it, you just say
DECLARE_OPTIONAL_REGION() directly in <symbols.h> (in place and instead
of the usual DECLARE_REGION()). This basically looks the same way in the
resulting object file but somehow LTO seems to like it better.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6096207b311d70c8e9956cd9406bec45be04a4a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Enable IPU for Volteer and Volteer2 variants for MIPI camera.
BUG=165340186
BRANCH=None
TEST=IPU is enabled and shows in lspci.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I66d60474e16c7a9aa8006d42b22510c1495dbd84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44628
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set psyspl2 to 97% of adapter rating, based on our experiment results.
BUG=b:160676773
TEST=Built and check firmware log.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4b621a8cc1749ee52a9f16a7ad2ae7a7aa0f7a5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
DRIVERS_WIFI_GENERIC is a dependency for these SAR settings.
However, coreboot.org builders are not failing, but chromium
builders are only for serial configurations. It's not clear as
to why. Either way correct this.
BUG=b:159304570
Change-Id: I978b622a3a5a2490b0e3aaa14c24807d5afdff9a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44825
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The gpio_common.h needs EINT_BASE from addressmap.h.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I20834e38343410526da0a489fed907acbf479d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Most of the code is generated using autoport.
Working:
* booting Arch Linux from SeaBIOS
* PCIe/SATA/USB ports (see overridetree and early_init for lists)
* LVDS, DisplayPort, VGA, 3.5 mm jacks, RJ-45
* keyboard, touchpad
* C-States, S3 suspend
Not working:
* rfkill hotkey
* color of the mute hotkey
* sleep f-key
Untested:
* internal speakers and microphone (defective on my machine)
* FireWire
* docking station
* TPM (SeaBIOS detects it, no further test done)
Signed-off-by: Pablo Stebler <pablo@stebler.xyz>
Change-Id: I916583fad375f16e5b02388cbcad2e8a993e042f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Rename the pch_init function to bootblock_pch_init and romstage_pch_init
according to the stage it is defined in.
TEST=successfully built and booted TGLRVP
Signed-off-by: Alexey Buyanov <alexey.buyanov@intel.com>
Change-Id: Ib7450fcdc3024dfb5e375a54f9bdcdca9bc373d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Returning a const uint32_t doesn't do anything, and it conflicts with the
declaration of sku_id() in include/boardid.h.
Change-Id: I2719e5782c9977f8ca4ce8f1dd781f092aa73d64
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1428708
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44746
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow HW schematic to correct DDSP_HPD1/2/3 and USB_OC3 pin.
BUG=b:165175296
BRANCH=none
TEST=Check all USB ports USB2 and USB3 both functional
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2f941141d761b1b69bc8f9ef0b0c4516062fec4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Removing entry covering root region leads to situation where
num_entries counter is set to 0. This counter is further decremented
in function obtaining address to last entry (see root_last_entry()).
Such negative number may be further used as an index to the table.
Current implementation may lead to crash, when user removes last entry
with imd_entry_remove() and then calls for example imd_entry_add().
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I6ff54cce55bf10c82a5093f47c7f788fd7c12d3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
One of the checks inside imdr_recover() was written with the
assumption that imdr limit is always aligned to LIMIT_ALIGN. This is
true only for large allocations, thus may fail for small regions.
It's not necessary to check if root_pointer is under the limit, since
this is implicitly verified by imdr_get_root_pointer().
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I25d6291301797d10c6a267b5f6e56ac38b995b7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Previously it was allowed to create an imd_entry with size 0, however
algorithm sets the offset of such entry to the exact same address as
the last registered entry.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: Ifa2cdc887381fb0d268e2c199e868b038aafff5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Add a check that root_size provided by the caller accounts for one
imd_entry necessary for covering imd_root region. Without this, we
may end up with writing on unallocated memory.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I0a39d56f7a2a6fa026d259c5b5b78def4f115095
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Get rid of the second check whether r is NULL (this is already done by imdr_has_entry()).
Signed-off-by: Anna Karas <aka@semihalf.com>
Change-Id: Ibee1664ee45b29d36e2eaaa7dff4c7cc1942010b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
