This change adds a user selectable option to enable all WiFi SAR
configs that apply to hatch.
BUG=b:138177048
Change-Id: I4b72f90896841e7c556d4a1b8cdad8ca89d01021
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Based on updated schematics, change polarity of USI_INT, and add
the reset and enable GPIOs to the touchscreen ACPI node. The stop
GPIO can't be used with the current implementation of _ON, as the
way it's wired will cause power sequencing to fail.
BUG=b:137133194, b:138240502
BRANCH=none
TEST=Compiles, don't have next board rev to test with
Change-Id: I1dfb8e649418e4c5e9b897fb4bc11393adc21ea2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This change provides an implementation of variant_devtree_update() for
kindred that disable eMMC controller when SKU ID = 1 or 3
BUG=b:132918661
TEST=Verify eMMC is disabled when SKU ID = 1 or 3
Change-Id: I8ccb4dae54f223881e0ced9e034bf45b994cc6f2
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch configures GPIO pin GPP_G7 as NF1 with internal pull down.
As per schematics SD host controller SD_WP pin is not connected to
uSD card connector. Configured gpio pin as NF1 with internal pull down
in order to overcome gpio default state in hatch which makes SoC
SD_WP pin is enable.
BUG=b:137729527
BRANCH=None
TEST=Able to write/read data to/from sd card after mounting card device.
Change-Id: I0187267670e1dea3e1d5e83d0b29967714d6065e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34396
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Following changes are done to enable ALC1011 codec on Helios
1. ACL1011 4 devices to I2C4
2. GPIO H13 is set to GPO as per schematics
Verified SSDT table and i2cdetect from kernel.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Change-Id: I0d71e3bd2d4493d059a33023c1afe1b630181d4f
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change provides an implementation of variant_memory_sku() for
helios that overrides memory ID 3 and 4 to 0 and 1 to workaround the
incorrect memory straps in hardware for board id 0 and unknown.
BUG=b:133455595
Change-Id: I38fab1f91decac5d0a146e5a6c74e88f677af305
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This change adds support for variant_memory_sku() that allows variant
to return memory SKU ID. Current implementation of memory_sku() is
renamed to weak implementation of variant_memory_sku(). Functionally
this change should be the same as before for all hatch variants. This
function will be overriden by helios in a follow-up CL.
BUG=b:133455595
Change-Id: I509c263ec08e0060c12ef1ea9fed673f1e3f3a41
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This patch makes VGPIO_3 GPIO PIN output and low independent of
cnvi is connected or not.
BUG=b:123062346
BRANCH=None
TEST=boot up Hatch device and make sure VGPIO_3 gpio pin is driven low.
Change-Id: I629b99676f56747de1b244724709e14069250097
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34376
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, bluetooth FW is not loaded after a reboot. In order to do
this, we have to disable the bluetooth disable gpio (GPP_C14) in
bootblock and re-enable it in ramstage.
BUG=b:137307516
BRANCH=None
TEST=boot up Hatch device and make sure (in dmesg) that proper
bluetooth FW in loaded
Change-Id: Ic5e447d9de57790f7a100e9e03f36b047c19d8f9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hatch and variants use GPP_A21 for trackpad IRQ and wake. Fix
overridetree.cb to advertise the right IRQ.
Change-Id: Ib87c858b89e8726c3bc80f83be0729ef4625268e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34248
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the AC/DC loadline values for all domains. Using the same
values as in arcada.
BUG=None
BRANCH=None
TEST=Build and Boot hatch EVT
Change-Id: If8ea48794d11dc68e40e6504c0d46a2b273a8ab6
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Before the system enters S0ix or S3, each GPIO community
will have its dynamic clock gating turned on. Upon return
to S0, the dynamic clock gating will be turned back off.
BUG=b:130764684
BRANCH=none
TEST=Used dut-power to verify that the clock gating is enabled
in S0ix and S3. Also used Store(..., Debug) statements in the
ASL code to verify it was getting called.
Change-Id: I20ff2aac035eaa5912af6c946d837567a4918bbf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Include the lpit.asl file in Hatch's DSDT definition.
BUG=b:130764684
BRANCH=none
TEST=S3 suspend/resume and S0ix entry/exit work correctly.
Ran > 200 iterations of suspend_stress_test and no issues found.
Change-Id: If8ebff3db091257e8452869636c0e024f3123e8b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
The dynamic clock gating is causing boards to miss interrupts
whose pulses are shorter than 4us. Disable it using FSP UPDs.
BUG=b:130764684
BRANCH=none
TEST=Compiles
Change-Id: I8f1ec8f7c31192bce2a761ec99b86638435dc27c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
HP_INT_L(GPP_H0) is configured for GPIO IRQ instead of APIC IRQ since
it needs to trigger on both edges. With GPIO IRQ, it is necessary to
configure the trigger type in coreboot to match the ACPI
configuration. This is because:
1. ACPI configuration is used by intel-pinctrl driver in Linux kernel
to re-configure the trigger type for the pad in GPIO DW0 config
register. This is done when kernel driver probes and requests irq for
its device.
2. On resume from S3, the pad configuration gets reset and coreboot
sets the trigger type to LEVEL. However, kernel driver does not probe
again. This results in the trigger type being configured incorrectly.
This change updates the GPIO configuration for GPP_H0 to set the same
trigger type as advertised in ACPI for the kernel.
BUG=b:132672011
TEST=Verified that S3 works fine. Verified that interrupt on GPP_H0
works fine on boot as well as after suspend/resume.
Change-Id: Ieb44c7403a2f4911b4a8f422053dee8bcfb91d85
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34181
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
increase reset off delay time
Goodix touchscreen cannot work in normal mode because PP3300_TOUCHSCREEN_DX
dropped. Configure GPP_D9 as enable pin in the devicetree.cb to fix the power
sequence. Increase reset_off_delay time from 1ms to 3ms to met the HW requirement.
BUG=b:135287161
BRANCH=None
TEST=local build and measure sequence with Goodix touch screen
Change-Id: I33140869990aa4715c780b0fa322921e450530ef
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33808
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the following GPIO settings.
1. Set Native termination for GPP_G0 - G4 SD card pins.
2. Set GPP_B19 to NF1.
BUG=b:123907904
TEST=Verified SD card functionality on hatch. Checked for SD detection,
transferred files to and from SD card.
Change-Id: I4549ac7377d7f58f51cda0eb96a62604fd31d2f2
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Previously, We had to use GPP_A21 for trackpad wake and GPP_D21 for
trackpad interrupts due to ITSS not honoring the INVERT config. Now
that's fixed, we can configure trackpad wake and interrupts on GPP_A21
only.
BUG=b:130436471
BRANCH=None
TEST=1. boot a hatch device and make sure we can move the cursor with the trackpad
2. Run powerd_dbus_suspend and wake by clicking on the trackpad and ensure
through "mosys eventlog list" that the wake source is the trackpad.\
3. Run "echo mem > /sys/power/state", wait until device goes into S3,
click trackpad to ensure device wakes.
Change-Id: I26a99206c42ba442f91ae577b98366fc2fd6c0ca
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Now that ITSS config is fixed, we can set the IOAPIC pad configs
correctly.
BUG=b:123967687
BRANCH=None
TEST=Make sure Hatch is booting and tested out trackpad to make
sure can move cursor and wake by clicking on the trackpad
after running powerd_dbus_suspend.
Change-Id: I0b125996338b6f16e03b7ca184f6337c696a5f64
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct i2c address of trackpad. It should be 0x20.
BUG=None
BRANCH=None
TEST=Verified trackpad works on pre-evt system
Change-Id: I7ded21ce8ff9e907e436777a27edb4273512011d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
A FPMCU power-control pin (GPP_C11) is added to the latest
hatch reference schematic.
Even though this is not implemented in hatch rev1 board, the future
hatch family boards with FPMCU should all have this control pin.
On the old boards without this control pin, GPP_C11 is a floating TP,
and thus this patch should be backward-compatible.
BUG=b:130307667, b:135216932
TEST=build
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: I6a84eeb6aab562258e749a8a5d09dadfa0e43587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is no need to add internal termination (PU/PD) on the
not-connected pads. This change gets rid of the terminations on the NC
pads.
Change-Id: I3df538d7127e5ef75e6e6ff9db3524e26f0450ed
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There is already an external pull-up/down resistor tied to
this pin to identify if the board is single-channel or
dual-channel memory SKU.
BUG=b:135496271
BRANCH=none
TEST=build
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Ie218657fd9dde113ab26cf5551d1dff1b6e392b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Hatch newer board revision do not use USB port5 for discrete BT.
Hence remove the port configuration and UBS2 P5 asl entry. The older
board version would continue to use USB2 P5 hence moved the entry to
overridetree.cb
Change-Id: I98297d6b81e3184b7b0a14710f3790f5df30d68b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Move the memory strap gpios to variant/gpio.h, as the memory straps
are different for helios.
Change-Id: I1833c9539687011ee27fd3e88c0581e30ca59354
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Helios has a number of GPIO changes w/r/t to its baseboard.
Override early, sleep and normal GPIOs as appropriate.
BUG=b:135257452
BRANCH=none
TEST=Compile only (no boards to test with)
Change-Id: I45793ad6515df5af5b925d92106bd943374353d4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gpio_key wakeup_event_action in the ACPI tables was backwards, causing
devices to wake up on pen insertion instead of removal. Changed to
EV_ACT_DEASSERTED.
BUG=b:134547896
BRANCH=none
TEST=Verified in OS, device only wakes up on pen removal
Change-Id: I0816ed9fb23cf00fd8e40bcdd25ff7a9f48badbd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33427
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change the SPD makefile to use the LPDDR3 SPDs. Set up the arrays
for mapping SoC DQS pins to LPDDR3 pins.
BRANCH=none
BUG=b:133455595
TEST=`FEATURES="noclean" FW_NAME="helios" emerge-hatch chromeos-ec
depthcharge vboot_reference libpayload coreboot-private-files
intel-cmlfsp coreboot-private-files-hatch coreboot chromeos-bootimage`
Ensure the firmware builds without error.
Change-Id: Iebaba2ec65dfcf36674b4733b421ada107b22b09
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33456
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch is not actually disabling HECI1 as it requires a dedicated FSP UPD
for WHL/CML SoC code to set this HECI1 chip config.
Change-Id: Ia88f3315a9dc3365d0acc13ed887e7c596c97c91
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Disable dynamic clock gating for the community cr50's IRQ lives on.
That IRQ is pulsed very quickly, and with clock gating enabled pulses
tend to be missed. This is expecially true on the default 0.0.22
firmware that cr50 comes with out of the factory.
BUG=b:130764684 b:130338605
BRANCH=None
TEST=Boot hatch with cr50 "intap" firmware that can vary the pulse width,
observe that even with sub-microsecond pulses no IRQs are missed.
Change-Id: I34d14fb7cc97e33eecfda2c99cc53a541c87662d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
One variant is asking for support for 16G 2666 LPDDR3, so adding
generic SPD for that.
BUG=b:133455595
BRANCH=None
TEST=None as this is not being used yet
Change-Id: If16a101119aabc30d6ea83e95e9ded2e089a982d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
One variant is asking for support for 8G 3200 DDR4, so adding generic
SPD for that.
BUG=b:132920013
BRANCH=None
TEST=None as this is not being used yet
Change-Id: I89cd3287aaf0baf384c4fe82d0881b0c48e09753
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33258
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RW_LEGACY section needs to be minimum 1M. For the 16MB BIOS
region, we had this region set too small, which was causing the
firmware_FMap FAFT test to fail.
BUG=b:133857135, b:129464811
BRANCH=None
TEST=test_that -b hatch <IP> firmware_FMap
Change-Id: Ie6311613ca3bb08e7f058a41d12f9a1153dc9c5e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Enable LTR for NVMe and WiFi PCIe ports so that they can use ASPM L1.2
BUG=b:134195632
TEST=Verified L1 substate with lspci on hatch:
Before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
After: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I7fce60897b78dde12747ac7fb857c988d16118ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33161
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the Kindred variant of Hatch by taking a copy of the Hatch files
as placeholders. Kindred-specific changes will happen in future CLs.
BUG=b:133181366
BRANCH=NONE
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_KINDRED
Change-Id: I09ad3da0505d599fc3797d7fa24b4dc170dcd18b
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There are indeed two temperature sensors hooked up to the EC, but they
are indexed as 0 and 1, not 1 and 2.
BUG=b:132999028
TEST=Boot hatch with hardened EC, observe no more index overflows
Change-Id: Ia7f503bc1dc941635db52fce40f217bf34da6d2b
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently, GPP_H0 gpio input rout is set to GPI_INT.
So, ACPI_GPIO_IRQ is required for GPP_H0 in devicetree
This change also aligns hatch's setting.
BUG=b:131742713
TEST=headset is working
Change-Id: Ie1264641bc4dfa5f98b6dab2d6f2133a6f9cbdb8
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
sarien/arcada:
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D18 IRQ mapped for H1 TPM.
hatch:
GPIO_COMM_0/1/2/3: Enable gpio community all PM configuration
GPIO_COMM_4: Disable RCOMP clock gating due to GPP_C21 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: Ia4d5483847a4d243b9038119d4bb5990591cc754
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The system should boot fine to OS on pressing power button before the
system enters G3. However, on hatch, we observe that the system waits
for few seconds at "Starting kernel" and then resets, with SD card tray
inserted and SD_CD# pad reset config set to DEEP. Hence configuring SD_CD#
pad reset config to PLTRST.
BUG=b:129933011
TEST=Built and verified on hatch.
Change-Id: Ic4466b96332f095ff39b28d98607e95fc3d12d6a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gpio table is only used by depthcharge, and depthcharge rarely
has a need for the "recovery" gpio. On a few boards it does use the
gpio as a signal for confirming physical presence, so on that boards
we'll advertise the board as "presence".
All these strings probably should have been #defines to help avoid
typos (e.g., the "ec_in_rw" in stout seems questionable since everybody
else uses "EC in RW").
Cq-Depend: chromium:1580454
BUG=b:129471321
BRANCH=None
TEST=Local compile and flash (with corresponding changes to depthcharge)
to 2 systems, one with a "presence" gpio and another without. Confirmed
that both systems could enter dev mode.
Change-Id: Id6d62d9e48d3e6646cbc1277ea53f0ca95dd849e
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updated GPP_A8 to be a GPI and SCI source, to support both wake and
notifications.
BUG=b:128941098
BRANCH=none
TEST=Compiles, simulated pen eject with PCH_INT_L signal. Both evtest
and waking from s0ix confirm this works. The output of /proc/interrupts
confirms the correct interrupt is triggered.
Change-Id: I080fb3cbfb3e2f55209ca31824b00ca820d70f78
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Patch corrects IRQ and GPIO configuration for RT5682 codec's Jack INT.
Switching IOAPIC to GpioInt because ACPI Interrupt() doesn't support
jack triggering on both edges.
BUG=b:130180492
TEST=build and boot on a CML EVT board.
Use evtest & verify headset jack detection functions as expected.
Change-Id: Ia9bf8d554b54554f9ac1e78fd44a508964c8a14d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Suggested-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32474
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Ensure Kohaku GPIO pins are configured correctly w/r/t Hatch. Implement the
base/override model for GPIOs (regular and early). The 'hatch' baseboard
contains the base GPIOs, and variants can override individual pads.
BUG=b:129707481
BRANCH=none
TEST=Compiles for all variants.
Change-Id: Ie5c83a0538d367ea11e9499f21cea41891d7a78e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Expose the Bluetooth BT_DISABLE_L signal in Hatch's devicetree,
on both USB2 port 5 and 10.
BUG=b:123293169
BRANCH=none
TEST=compiles, verified kernel is able to find the reset-gpio
Change-Id: I6e4d9786e44f12da71533b6740fdd390f3a57e40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32216
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves the I2C/SPI devices and configs which do not apply
to all variants to override tree. Currently, there are just two
variants. However, as we prepare to add more variants, these devices
need to be moved out of the base devicetree.
BUG=b:129728235
TEST=Verified that I2C/SPI devices are present in static.c for hatch
and hatch_whl.
Change-Id: I9426f6bf5f8514de5f1889e22e57105749fd92de
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32138
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In S3 the PCH is driving the DEVSLP signal low, assuming that the SATA device
is already powered off. However on hatch the SATA power is still enabled. And,
since DEVSLP is low, this causes the SATA device to not enter low power state.
The fix here is to set the pad config to be reset on PLTRST assertion which
will cause the pin to be high impedance state and will be pulled up by the
SATA device.
BUG=b:126611255
BRANCH=None
TEST=Make sure that S3 and S0ix is working fine on hatch.
And also make sure that DEVSLP is pulled high in S3.
Change-Id: Ifb6a71a72244522c8dd8d48e9b9f8dc6feef8981
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adding Kohaku as a variant of hatch.
BUG=b:129706980
BRANCH=NONE
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
make sure HATCH_KOHAKU is built as well.
Change-Id: I5b451f421f6d353005e6b73eac180dcec2e8b0c0
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For HW require to change GPIO_E1.
Change GOIO_E1 setting from NF2(SATAGP1) to NF1(SATAPCIE1).
BUG=b:123730924
TEST=flash BIOS and make sure hatch boots up properly
Change-Id: I0f5569e13b17a2dc713be5031a63436e8f31f911
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32099
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_A12 has a Native3 (SX_EXIT_HOLDOFF#) mode, which allows to delay
resuming to S0. If this pad is not locked and platform was not initially
designed for this functionality, malware could reconfigure this pads
setting under OS (switch to Native3), which would make platform not able
to resume until G3 is applied. To prevent misuse of this pad,
re-configure this pad before entering S3 and S5 to guarantee that the
pad configuration is correct.
BUG=b:128686027
Change-Id: I1e7979baa491acf2c56d223afb4618f0f6429e37
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPP_A12 is being used as FPMCU_RST in hatch. This GPIO is being padlocked in
FSP and cannot used in kernel. Hence unlock the GPIO pads to export this pin
in kernel to be used as FPMCU_RST.
BUG=b:128686027
BRANCH=None
TEST=Read Pad Configuration Lock (PADCFGLOCK_GPP_A_0) register.
localhost /sys/class/gpio # iotools mmio_read32 0xfd6e0080
0x00000000
localhost /sys/class/gpio # echo 212 > export
Change-Id: Ie0439956e6c8e386435e535665ccaf2ab82adeb0
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32126
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Deassert EN_PP3300_WWAN to turn the WWAN module completely off when
entering S5. This is the same fix in commit eeb475c5c for coral board.
BUG=none
BRANCH=none
TEST=On hatch, Perform a quick system power cycle, verify that the modem
is powered cycle and the SIM with PIN lock enabled requests unlocking.
Change-Id: I3ec8ccb7618189b9e8586f5571a68d3309597ee7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds DPTF based Fan speed control for CML based Hatch system.
BUG=None
BRANCH=None
TEST=Built and tested fan speed with different temperatures
Change-Id: I3c2a679dc67eecb17098ce0f0c9703c679473a2d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the latest hatch schematics, BOOT1 for the FP MCU is now connected
to the AP. Configuring it to be the same as BOOT0.
BUG=b:126455006
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a -c max
Change-Id: Ibb451983674a7d812dc562cb8addb1dc50fb155c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set tcc_offset value to 10C. It configures the Thermal Control Circuit (TCC)
activation value to 90C. This prevents any abrupt thermal shutdown by taking
early thermal throttling action when CPU temperature goes above 90C.
Change-Id: Ifee0fcc326530622b04e60af0f3b9cb9e3aea7ea
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31984
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AP communicates with FP MCU through gspi1.
BUG=b:126455006
BRANCH=None
TEST=ensure during bootup we see spi id spi-PRP0001:01 in dmesg
FP MCU fw is not ready yet, so not much testing to be done yet.
Signed-off-by: Shelley Chen <shchen@google.com>
Change-Id: I2eba205d5e63664dca684fbd849454c5a2fe0d0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32017
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SAR0, which is an SX9310. The schematics and layout have a second
SAR1 sensor provisioned on I2C4, with an interrupt of GPP_A6, but this
is not populated.
Signed-off-by: Evan Green <evgreen@chromium.org>
BUG=b:128540461
BRANCH=none
TEST=Boot kernel with sx9310 driver, see it come up happily
Change-Id: I63943cc7da5ff56f6ef6dcbd99bb8f8f031e8bf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the HUNG_TASK as a wakeup host event, as it's used by S0ix failure
detection to wake the system back up if a suspend to S0ix never
asserted S0_SLP#.
BUG=b:123716513
BRANCH=None
TEST=Test S0ix on Hatch with appropriate EC and kernel changes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I447211892df210af97e8df0380bab032b14cbee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32004
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Assign the FSP UPDs for HPD and DDC of DDI ports. FSP assumes that all
DDI ports are enabled and hence configures the HPD and CLK for DDI ports.
This patch initializes only the required UPDs to enable display ports.
BUG=b:123907904
TEST=DP devices working correctly.
Change-Id: Ic0c172cd3d087fc8f49b01ab23feffdababf7166
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We were used to set the same values in the system and board tables.
We'll keep the mainboard values as defaults for the system tables,
so nothing changes unless somebody overrides the system table hooks.
Change-Id: I3c9c95a1307529c3137647a161a698a4c3daa0ae
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
From doc#573387 CML System Memory DQ DQS Rcomp Mapping Information
User Guide, RCompResistor[0] should be 121.
BUG=b:122959294
BRANCH=None
TEST=emerge coreboot and make sure boots up
Change-Id: If69e7fb41e79d88d21b0e50fb65107a1686d696a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31868
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MEM_CH_SEL is used to indicate whether we are on a single or dual
channel device, where MEM_CH_SEL = 1 for single channel skus and
MEM_CH_SEL = 0 for dual channel skus. Initialize single_channel field
(from GPP_F2), which will in turn initialize MemorySpdPtr pointers in
cannonlake soc code. In the first build, we did not use GPP_F2, so we
need to add an internal pulldown as those early devices were all dual
channel devices.
BUG=b:123062346, b:122959294
BRANCH=None
TEST=Boot into current boards and ensure that we have 2 channels as expected
Also, verify that GPP_F2 is set to 0.
Change-Id: I89d022793580be603a93d0b177d73ce968529b5c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The board version is part of EC's EEPROM, select Kconfig items to enable
requesting the EC for board version.
BUG=b:128385395
TEST=Verified the mainboard version is from EC's EEPROM.
Change-Id: I4bc1cac43c6cf73522f3a4bee89cc000a430d996
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31858
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change reads DRAM part number from EEPROM if available and
returns it using the SoC callback (mainboard_get_dram_part_number).
BUG=b:127609572
TEST=Verify that DRAM part number from EEPROM is added to DMI table
17 (dmidecode -t 17).
Change-Id: I6ade6999828b6d67aa78d04199138f195a97ba8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adding Hatch_whl as a variant of hatch. This is a snapshot of the WHL
version of hatch so that we can rebuild the bios images for Hatch with
WHL SoC.
BUG=b:127310803
BRANCH=NONE
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
make sure HATCH_WHL is built as well.
Change-Id: I24510fa226878582a61f1846f0b56a2c65204a92
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Following changes are done to enable audio support on hatch
1. Enable I2C4 device at 400Khz at 1.8V
2. Configure GPIO for HP INT and SPKR_PA_EN
3. Add ACPI entry for RT5682 and MAX98357A
4. Enable I2S0 and I2S1 lines
5. Enable generic max98357a driver in Kconfig
BUG=b:123738217
BRANCH=none
TEST=Check SSDT table for RT5682 & MAX98357a entry.
Verify audio using Sound Open firmware (SOF)
Change-Id: I93f3917c19cc3f0f8fd7b5e1b4d9b24a59f45f84
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In preparation for the transition of hatch from WHL to CML, we are
creating a checkpoint called hatch_whl that we can use for creating
firmware compatible with the WHL hatch variant.
BUG=b:127310803
BRANCH=NONE
TEST=NONE
Change-Id: Iecae584ee6feefcf29955a4720e9c24bdc8abe6d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For Chrome OS (or vboot), The PRESERVE flags should be applied on
following sections:
RO_PRESERVE, RO_VPD, RW_PRESERVE, RW_ELOG, RW_NVRAM, RW_SMMSTORE,
RW_VPD, RO_FSG (b:116326638), SI_GBE (chromium:936768),
SI_PDR (chromium:936768)
With the new PRESERVE flag, we don't need RO_PRESERVE and RW_PRESERVE in
the future. But it's still no harm to use it if there are multiple
sections all needing to be preserved.
BUG=chromium:936768
TEST=Builds google/eve and google/kukui inside Chrome OS source tree.
Also boots successfully on eve and kukui devices.
Change-Id: I6664ae3d955001ed14374e2788d400ba5fb9b7f8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
coreboot did not program all GPIOs from C0 to C7 correctly which are
SMBUS GPIO. Some of the GPIOs are left in default mode which is
native function but we need to configure as GPIO mode and provide proper
configuration as per schematic.
After fixing GPIO, CSME power gating issue also gets fixed since SMBUS was not
getting idle due to GPIO configuration and CSME was not getting power
gated due to SMBUS.
BUG=b:123702553
BRANCH=none
TEST=Check on hatch board. CSME was not getting power gated for s0ix.
After applying this patch CSME is power gated now
Change-Id: I5c6b9310dcc7bade0023abd5524781ce71df28be
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Hatch implements active high SD_PWR_EN and requires a workaround
in _PS0 and _PS3 control methods to make sure SD_PWR_EN stays low
in D3. Select MB_HAS_ACTIVE_HIGH_SD_PWR_ENABLE to enable the same.
BUG=b:123350329
Change-Id: I96ab9660eb50100207fe9a237f5924b65eae0928
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SD_CD# in Cannonlake PCH is also wired to an internal virtual GPIO,
expose that GPIO for kernel to configure card detect IRQ.
BUG=b:123350329
Change-Id: I566cc2eb11dc257366897a1efba905b8ddcf493d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For some reason, wake does not currently work from GPP_D21, but IRQs
are working fine from that gpio. Thus, we have to switch IRQ to
GPP_D21 and wake to GPP_A21, which was previously used for IRQs from
the trackpad. Additionally, we need to use two gpios for irqs and
wake source at the moment because of b:123967687, where FSP is locking
down PCR and configuring ITSS. We need to configure the wake source
gpio as inverted and the IRQ gpio as non-inverted until the bug is
resolved.
BUG=b:121212459
BRANCH=None
TEST=run evtest with trackpad
Use trackpad with ChromeOS UI and make sure it reacts as expected.
Run powerd_dbus_suspend and press trackpad and make sure DUT
wakes.
Change-Id: I7b236136befc05c6586d9ba69185ed4b5d385273
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EC software sync had been disabled because BIOS was not bundling a
useful EC image. This is no longer required. This CL removes that
change so EC software sync is enabled by default.
BUG=b:124208414
BRANCH=None
TEST=Tested with a system that have a different RW image and verified
that this image was overwritten to the one bundled in the BIOS and
that the EC was running its RW image.
Signed-off-by: Scott Collyer <scollyer@chromium.org>
Change-Id: Ic1ffdb62e9fa2cacb3296cb3807082f23e171ab5
Reviewed-on: https://review.coreboot.org/c/31537
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change bumps up the BIOS region to 28MiB to use the hole
between SI_ALL and SI_BIOS. Since this SPI flash part is 32MiB, only
the top 16MiB actually gets memory mapped. Thus, the change ensures
that only RW_LEGACY lies in the 12MiB that is not memory mapped.
BUG=b:123443737
TEST=Verified that hatch still boots up. Ensured that fmap dump looks
correct.
Change-Id: I5832d2b89c7eedfc270755e2add16131cfbddff4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This implementation configures GPIO (GPP_A21, GPP_C21, GPP_D16)
pad in non-inversion mode i.e Rx PAD state is not inverted as
it is sent from GPIO to IOAPIC.
BUG=b:123315212
TEST=Tested for below:
-> Verify touchpad is working fine.
-> TPM init is successful and boot with fixed boot media.
Change-Id: I6034fd07ccc96a19218d57ef8bb9049c4b963ea5
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Traditionally, we have always allocated 1 DRAM ID per part number.
However, on nami, we have run out of DRAM IDs because we have
supported so many different parts. We are now adopting the use of
generic SPD files that are feature-based rather than specific to each
part, allowing us to support multiple parts with a single SPD.
The common SPDs were created by taking current SPDs in Nami (which is
using the same DDR4 parts as Hatch) and zeroing out all the
manufacturer information and part names. Additionally, we zeroed out
bytes 128 (raw card extension, module nominal height), 129 (module
maximum thickness), and 130 (reference raw card used) after verifying
that they are not used in FSP. We verified with these fields zeroed
out, all nami devices could boot up without errors. We also verified
on the two Hatch skus that we have (4G 2400, 8G 2666) that the generic
SPDs boot properly.
BUG=b:122959294
BRANCH=None
TEST=Make sure that we can boot up on both 4G Samsung and 8G Hynix DDR4
devices that we currently have.
Change-Id: I14d9e6b13975b6a65b506e6cd475160711b8f6d4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This implementation adds support to create ACPI package for USB port
capability (_UPC) and physical location of device (_PLD) for USB2 port 10.
BUG🅱️123375275
TEST:Verify _UPC and _PLD ACPI packages gets published for USB2 Port 10
in SSDT and BT is functional in discrete and integrated mode.
Change-Id: Ifeab24505a700e8e4677be20074c7d0400769cec
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31197
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake
the AP from suspend. Also create a task to initialize the hostevent
wake mask properly.
BUG=b:123325238,b:123325720
BRANCH=None
TEST=from AP console: powerd_dbus_suspend
from EC console: hostevent (make sure wake mask set)
from EC console: gpioset PCH_WAKE_L 0
Make sure device wakes up
Also, checked to make sure keyboard press wakes up
device from S3.
Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch enables relevant GPIOs to enable WWAN. WWAN also requires to
enable USB 2 port 6 and USB3 port 5 which is already enabled in device
tree related changes.
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I1559bbc6168aec1a369bf3291d2c1e2f9a2fbe07
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable PCIe WLAN for hatch
1. Enable PCI port 14 for PCIe WLAN
2. Enable CLKREQ, CLK SRC 3 for PCI port 14
3. GPIO pad config for WLAN and BT
USB port for BT has already been enabled so not included in this patch
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I4f2a6eb37a467ad8b8cdde8fe6b657fabb383b04
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
set SaGv = SaGv_Enabled , To Enable System Agent dynamic frequency support
set HeciEnabled = 1, To Enable heci communication
set speed_shift_enable = 1 To Enable Speed Shift Technology support
Change-Id: Iea90a65a77ef5e45a802cfe6fd31e1921163b02b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Most boards currently do not use EC firmware from SPI flash in the
IFD, this hides this option by default and shows it only for boards
that need it.
A new config variable MAINBOARD_USES_IFD_EC_REGION is introduced to
enable this option for boards that need it.
The following list of boards requiring this was provided by
Lijian Zhao:
1. intel/cannonlake_rvp
2. intel/coffeelake_rvp
3. intel/icelake_rvp
4. google/sarien
5. google/hatch
Change-Id: I52ab977319d99a23a5e982cc01479fe801e172a7
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This patch disables the SA IPU for hatch since it is
not using the IPU.
Change-Id: Ib2afc4cc4fd7ef98365b0b98130b0e8bc757ac2a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Correcting order of display related GPIOs and also adding not connected
pin definitions for display GPIOs
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I9498284d263516f65513d6395883b6b09dd70fd5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch enables the SATA for hatch,
* Enable the SATA port 1.
* Configure the GPIO for SATA.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Iaf800d1531688c3d3b82600038ea1d7160ae4b0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30435
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
