amd_generate_powernow is never called by in lpc_slave_ops.
Move it to lpc_ops like on all other AMD southbridges.
TESTED on Gigabyte ga-m57sli-s4
Change-Id: I7db036e681d591a19e15dd3eaafb88b72a41bea1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17977
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Write gpio level twice to make sure the level is set
after pins have been configred as GPIO and to minimize
glitches on newer hardware.
Required to set correct GPIO layout on T500.
Tested on T500.
Change-Id: I691e672c7cb52ca51a80fd29657ada7488db0d41
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18012
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with
the ability to perform tx and rx of flash command and response at the
same time. Instead of introducing this notion at SPI flash driver layer,
clean up the interface to SPI used by flash.
Flash uses a command-response kind of communication. Thus, even though
SPI is duplex, flash command needs to be sent out on SPI bus and then
flash response should be received on the bus. Some specialized x86
flash controllers are capable of handling command and response in a
single transaction.
In order to support all the varied cases:
1. Add spi_xfer_vector that takes as input a vector of SPI operations
and calls back into SPI controller driver to process these operations.
2. In order to accomodate flash command-response model, use two vectors
while calling into spi_xfer_vector -- one with dout set to
non-NULL(command) and other with din set to non-NULL(response).
3. For specialized SPI flash controllers combine two successive vectors
if the transactions look like a command-response pair.
4. Provide helper functions for common cases like supporting only 2
vectors at a time, supporting n vectors at a time, default vector
operation to cycle through all SPI op vectors one by one.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17681
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Initial work based on db-ft3b-ls and code released by Eltan. Board
boots with some limitation.
Now the AGESA binary is harcoded and board specific until it's fixed
by the SoC vendor.
memtest86+ from external repo skips looking for SPD on SMBus, which when
performed cause memtest86+ to hang. Still didn't tried whole test suit.
SeaBIOS 1.9.3 have some problems with USB which lead to no booting in
some cases. Full log:
https://gist.github.com/pietrushnic/787cbf63f610ff4f6b4ac13e5c20b872
SeaBIOS from PC Engines repository (https://github.com/pcengines/seabios)
works fine. Those changes are planned for upstream.
Information about obtaining and booting Voyage Linux:
https://github.com/pcengines/apu2-documentation#building-firmware-using-apu2-image-builder
Change-Id: Id23e448e27f4bba47b7e9e7fa7679e2690c6e4bc
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/14138
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Select this to provide menu in menuconfig to add flash
descriptor file. ME or GbE firmwares themselves are not
required, but integrated NIC MAC and SPI configuration
fields are still useful.
Change-Id: I14b86e2f38ec39924d2cbf0932d82f66ed356a03
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17805
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Scratchpad register was read too
late in ramstage so acpi_is_wakeup_s3() did not evaluate
correctly.
This fixes low memory corruption at 0x1000-0x102c and the lack
of coreboot tables (util/cbmem not working) after S3 resume.
This also fixes console log from reporting early in ramstage
"Normal boot" while on "S3 resume" path.
Change-Id: I2922a15a90d2f8272c3482579bdd96f8f33e9705
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17675
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Also fixes console log from reporting
early in ramstage "Normal boot" while on S3 resume path.
Change-Id: I4e2eabc59ff87b7ed40cfc9885bbe0256fe4a695
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17674
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The value for _size was not evaluated correctly if ramstage
is relocated, make the calculation runtime.
While touching it, move symbol declarations to header file.
Change-Id: I4402315945771acf1c86a81cac6d43f1fe99a2a2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17784
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Make sure relocation code reaches DRAM before issuing any
SMIs. Snooping and cache coherency may have undefined
behaviour as CPUs do not have uniform MTRR layout yet.
Change-Id: I47a7d684e05ff8c1c2f1f6a5bf8c0bbc561d9eac
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17712
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CHIPSEC found that the TCO_Lock was not set.
This is used to prevent changing the TCO_EN bit.
Change-Id: I42364dbef2511e656662566cf94591e76c6847ed
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Reviewed-on: https://review.coreboot.org/17351
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Doing PCI config operations via MMIO window by default is a
requirement, if supported by the platform. This means chipset
or CPU code must enable MMCONF operations early in bootblock
already, or before platform-specific romstage entry.
Platforms are allowed to have NO_MMCONF_SUPPORT only in the
case it is actually not implemented in the silicon.
Change-Id: Id4d9029dec2fe195f09373320de800fcdf88c15d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17693
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
I liked the style of code in pci_mmio_cfg.h more, and used those to
replace the ones in io.h.
Change-Id: Ib5e6a451866c95d1edb9060c7f94070830b90e92
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17689
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The code originates from times before __SIMPLE_DEVICE__ was
introduced. To keep behaviour unchanged, use explicit PCI
IO operations here.
Change-Id: I44851633115f9aee4c308fd3711571a4b14c5f2f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17720
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
Change-Id: If62537475eb67b7ecf85f2292a2a954a41bc18d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17545
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
Change-Id: I943e354af0403e61263f1c780f02c7b463b3fe11
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17529
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit 36b81af (spi: Pass pointer to spi_slave structure in
spi_setup_slave) changes the way spi_setup_slave handles the spi_slave
structure. Instead of expecting spi controller drivers to maintain
spi_slave structure in CAR_GLOBAL/data section, caller is expected to
manage the spi_slave structure. This requires that spi_flash drivers
maintain spi_slave structure and flash probe function needs to make a
copy of the passed in spi_slave structure.
This change fixes the regression on Lenovo X230 and other mainboards.
Change-Id: I0ad971eecaf3bfe301e9f95badc043193cc27cab
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17728
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
These headers & comments indicating a lack of functionality don't help
anything. We discourage copyrights and licenses on empty files, so
just clear these.
Change-Id: Id2ab060a2726cac6ab047d49a6e6b153f52ffe6d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17657
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
1. Define a new structure spi_ctrlr that allows platforms to define
callbacks for spi operations (claim bus, release bus, transfer).
2. Add a new member (pointer to spi_ctrlr structure) in spi_slave
structure which will be initialized by call to spi_setup_slave.
3. Define spi_claim_bus, spi_release_bus and spi_xfer in spi-generic.c
which will make appropriate calls to ctrlr functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb2326e3aab1e8f4bef53f553f82b3836358c55e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17684
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For spi_setup_slave, instead of making the platform driver return a
pointer to spi_slave structure, pass in a structure pointer that can be
filled in by the driver as required. This removes the need for platform
drivers to maintain a slave structure in data/CAR section.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ia15a4f88ef4dcfdf616bb1c22261e7cb642a7573
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17683
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Use size_t instead of unsigned int for bytes_out and bytes_in.
2. Use const attribute for spi_slave structure passed into xfer, claim
bus and release bus functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ie70b3520b51c42d750f907892545510c6058f85a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17682
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This allows us to set MMCONF_SUPPORT_DEFAULT since we enable
MMCONF early in romstage.
Change-Id: I380cf483bfe4e2d64969110ae6d5d04c3ced2418
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17532
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This allows us to set MMCONF_SUPPORT_DEFAULT since we enable
MMCONF early in romstage.
Change-Id: I994bb257db96300c2eb8872be6fae2a92bbabab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17531
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SSCN and FMCN methods provide the optimal HCNT/LCNT timing values to
the driver, and are necessary when using I2C devices (eg, trackpad and
touchscreen) in ACPI (vs PCI) mode. Add these methods using the
timing values from Broadwell, which work for Haswell/Lynxpoint as well.
TEST: build google/peppy with trackpad/touchscreen devices in ACPI mode,
observe proper operation under Windows [8.1/10] and Linux [Mint 18]
Change-Id: I25f07ac474b041358315530e5f391bb33d9c4d04
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17620
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Prabal Saha <coolstarorganization@gmail.com>
The defines of device IDs reflects the vendor namespace
the ID has been allocated from.
Change-Id: Id98f45d5984752a9e8c0484d4cb94e93e55b12f6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17510
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
flash_programmer_probe is a property of the spi flash driver and does
not belong in the spi_slave structure. Thus, make
spi_flash_programmer_probe a callback from the spi_flash_probe
function. Logic still remains the same as before (order matters):
1. Try spi_flash_programmer_probe without force option
2. Try generic flash probing
3. Try spi_flash_programmer_probe with force option
If none of the above steps work, fail probing. Flash controller is
expected to honor force option to decide whether to perform specialized
probing or to defer to generic probing.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I4163593eea034fa044ec2216e56d0ea3fbc86c7d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17465
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
RW flag was added to spi_slave structure to get around a requirement on
some AMD flash controllers that need to group together all spi volatile
operations (write/erase). This rw flag is not a property or attribute of
the SPI slave or controller. Thus, instead of saving it in spi_slave
structure, clean up the SPI flash driver interface. This allows
chipsets/mainboards (that require volatile operations to be grouped) to
indicate beginning and end of such grouped operations.
New user APIs are added to allow users to perform probe, read, write,
erase, volatile group begin and end operations. Callbacks defined in
spi_flash structure are expected to be used only by the SPI flash
driver. Any chipset that requires grouping of volatile operations can
select the newly added Kconfig option SPI_FLASH_HAS_VOLATILE_GROUP and
define callbacks for chipset_volatile_group_{begin,end}.
spi_claim_bus/spi_release_bus calls have been removed from the SPI flash
chip drivers which end up calling do_spi_flash_cmd since it already has
required calls for claiming and releasing SPI bus before performing a
read/write operation.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Idfc052e82ec15b6c9fa874cee7a61bd06e923fbf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17462
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently, the coreboot log of a Lenovo X60, not having any IDE devices
connected, there is a trailing whitespace in the output.
[…]
PCI: 00:1f.1 init ...
i82801gx_ide: initializing...
PCI: 00:1f.1 init finished in 11 usecs
[…]
Reorder the whitespaces, so they are added when needed.
Change-Id: I640e514c89fe0246a847d1fd088def1c88e864f8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/11870
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There is mismatch of VENDOR_ID_AMD with DEVICE_ID_ATI, also
the device IDs have not been defined.
Change-Id: I3076cb08e3181e7f86de38deb18f1661f037bc38
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17508
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
There is mismatch of VENDOR_ID_AMD with DEVICE_ID_ATI, also
the device IDs have not been defined.
Change-Id: I0d85893169fe877e384746931605f563c50308b2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17509
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
If this information is needed, use make V=1. That will print the actual
command, not a command that needs to be updated with every addition if
it's going to stay in sync.
Change-Id: I64d33d93c7fad3359d8ef78657bdb86d1fb4d4a1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/17328
Tested-by: build bot (Jenkins)
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
amdfwtool was getting the ROM size as a #define when it was built.
It has been updated to pass it in as a command line parameter, so
now it can be built just once for abuild as a shared tool.
Update the calls to amdfwtool to pass the ROM size.
All platforms using amdfwtool had the output verified using
a binary compare.
This reverts commit 0529236ed2
(Makefile.inc: Don't share amdfwtool between platforms)
Change-Id: I188b34e08249f2d00bd48957ced750b21f1ec348
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/17327
Tested-by: build bot (Jenkins)
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801dx.
Change-Id: I32888930d3742432a73dfc0a32c6586186e6757c
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/17297
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since IFD format is floating, ifdtool needs to be parameterized with a
chipset it is dealing with. Add -p <chipset> argument to ifdtool
invocations if chipset provides it.
Change-Id: I4fd1783b5d994617912aedcf17adc2a98c97227b
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17258
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add Stoney specific code subtree and fix Makefles and Kconfig files.
Author: Charles Marslett <charles@scarlettechnologies.com>
Original-Signed-off-by: Marc Jones <marcj303@gmail.com>
Original-Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Tested-by: Marshall Dawson <marshalldawson3rd@gmail.com>
(cherry picked from commit c3a469d11e4676b3b63d11a30955113291d00ec8)
Change-Id: Ic4d97a3745f7fc5a637ae6da17a9009b9757136e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/17217
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Carrizo (00660F01), Merlin Falcon (00660F01), and Stoney Ridge (00670F00)
locate the HD audio controller on the northbridge root complex at 9.2
instead of the FCH. This duplicates the existing ASL into the northbridge
directories and reports the correct address.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit f68206c2b42c90076efd968a99f4d3a49e403438)
Change-Id: I6d42bb40ad58c7f35e8c88ff27ebd327d656c021
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/17216
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The Stoney processor can use multiple directory structures. Turn
this feature on in the makefile.
Original-Signed-off-by: Marc Jones <marcj303@gmail.com>
Original-Tested-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
(cherry picked from commit a3334632fd53c07a046c9b23161f6ee67e5cb16e)
Change-Id: I40a9ef2e6bed51bc339d3f9ae7c6f316192c4a78
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/17149
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Zheng Bao <fishbaozi@gmail.com>
Make the PSP2 smufirmware2 name unique so the command-line option
gets picked up.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: <marcj303@gmail.com>
(cherry picked from commit 98cf3880797f72aeb7169c3f8718a10092af9624)
Change-Id: I5430cf8b81fb03c95e6ee9d7e53455e6224256ff
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/17146
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Replace the use of the old device_t definition inside
southbridge/broadcom/bcm5785.
Change-Id: I091b07439ff918efa52cf8f8270484131fd0cec5
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16690
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
- Update lines to make them shorter than 80 chaacters
- Update using #defines from acpi_ivrs.h
Change-Id: I1bf6cdac00e28f5b0969fd8f98e37c66f8e43110
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16568
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Functionally, this should be roughly the same. The only real difference
should be removing the 4 bytes of padding from the end of the 4 byte
entries. The spec mentions a boundary for the 4 byte entries (which we
are ignoring), but doesn't mention a boundary for the 8 byte entries,
and I can't think of any other reason that the padding might be needed.
- Wrap long lines.
- Combine if statements to clean up indentation.
- Use #defines from acpi_ivrs.h to make commands easier to understand.
- Remove padding from 4 byte entries that made them 8 bytes in length.
- Set the pointer p at init, and clear the value at p if the device
we're looking at is enabled instead of setting p in every if statement.
- Look at the command type to update current and length.
- Treat malloc & free as if they were typical instead of coreboot
specific versions. Check to make sure the malloc worked and only
free on the last loop instead of every time.
Change-Id: I79dd5f9e930fad22a09d1af78f33c1d9a88b3bfe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16532
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Replace the use of the old device_t definition inside
southbridge/amd/agesa/hudson.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I39cd2afe5e2b6ee3963fd3e949eab1db9e986d71
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16401
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/ibexpeak.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ic569aada9301b37e73196872584e191d553acd86
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16408
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801gx.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ia257318a7068b54739f319bfbba35f2a07826940
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16370
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801ix.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ibf20e6c08994b09d2a2e68a1a1d38a7a477493aa
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16403
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/via/vt8237r.
Change-Id: I9c1211e698ef35f56dd71c2c021dea680091c1ee
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16489
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/sis/sis966.
Change-Id: I9e731fedc6f21eaa2685f794ea2172eb4800628b
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16488
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/nvidia/mcp55.
Change-Id: I98ac468940eaf6c456fa95540ec3e718edfe26a7
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/nvidia/ck801.
Change-Id: I43d4d2175f0b6b9e7e2e6fe665ba3d99d792427c
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16486
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb800.
Change-Id: I488cde4504128331106f50b34869905e30f5ab83
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16480
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb700.
Change-Id: I44b0be2070719066dd18bbf2882c417caef5d8b2
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16479
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb600.
Change-Id: I0227cc0c611324f513f8170c9d8819a88af39b39
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16478
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/rs780.
Change-Id: Ia9929baeec7423e9e2f06324038ddfbec006beb7
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16477
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/rs690.
Change-Id: Ief43393f62312bfe82e960faf56b1e2ec048f4ff
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16476
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/pi/hudson.
Change-Id: I8b22a8d9f0e90afaf0f218c5c0924a78883b7498
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/cimx.
Change-Id: Ibe2766b956b0ca02be63621aee9a230b16d9923b
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16474
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/amd8111.
Change-Id: I76cdc32171b7ce819b53c534b3a5e57e9dd5f3dd
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16473
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801dx.
Change-Id: Ic08a23f672f8b5e40b837d49a9475d52c728a306
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16485
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801ax.
Change-Id: I46f0cc92e1034f045988b42df7246f5d0c8d24fc
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16484
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82371eb.
Change-Id: Ie15a656c817a2ffe0f44ee3a89659d138a1bf212
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16483
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i3100.
Change-Id: Ic9616d5135cfb7206e086e51aaf82eb66540c4bb
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16482
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/fsp_rangeley.
Change-Id: I6665f85c74eb3e37d78f6eecbec977dc21a5ad12
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16481
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Defining this OpRegion for SMBus controller prevents linux kernel
driver i2c-i801 from registering SMBus under sysfs, with following
error in dmesg:
ACPI Warning: SystemIO range .. conflicts with OpRegion .. (\_SB.PCI0.SBUS.SMBI)
Solution taken from intel/bd82x6x. Worth noting we do not
define ENABLE_SMBUS_METHODS anywhere currently.
Removed remaining reference to HSTS from GETAC P470.
Change-Id: I7c13d344b0343387681b46019cc5061b1435b46b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16266
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
The field that was previously named 'efr' is actually the iommu feature
info field. The efr field is a 64-bit field that is only present in
type 11h or type 40h headers that follows the iommu feature info field.
Change-Id: I62c158a258d43bf1912fedd63cc31b80321a27c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16508
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/bd82x6x.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I7166bfab7904f80b745855d3bbcfb910cbc89f56
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16407
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The recent changes to this file from commit 6e5421d2
(sb/amd/sb700: Add option to increase SPI speed to 33MHz)
were accidentally removed in a code cleanup patch:
commit ba28e8d7 (src/southbridge: Code formating).
Change-Id: I6cf3e8f29d5c0384d35637f35e051be40318d20f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16384
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: build bot (Jenkins)
Some SB700-based systems and ROMs support high speed (33MHz) SPI
access instead of the power-on default 16.5MHz. Add an option
to enable high speed SPI access in the bootblock, and set the
default value to Disabled. This greatly decreases boot time on
SB700-based systems, especiall when a large payload is in use.
On a KGPE-D16 with a Petitboot (Linux + initramfs) payload, the
command prompt was accessible within 20 seconds of power on, which
incidentally is faster than the proprietary BIOS on the same machine
could even reach the GRUB bootloader.
Change-Id: Iadbd9bb611754262ef75a5e5a6ee4390a46e45cf
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Test: Booted KGPE-D16 with Linux payload
Reviewed-on: https://review.coreboot.org/16306
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Since RTC is now a Kconfig ensure RTC is selected on the
x86 chipsets which are in Chrome OS devices. This allows
the eventlog to have proper timestamps instead of all
zeros.
BUG=chrome-os-partner:55993
Change-Id: I24ae7d9b3bf43a5791d4dc04aae018ce17fda72b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Port commit e08493 to the SB700 platform
Change-Id: Ie18c6cc0ccb31a0d16a80fcb4c2e147c19e228fe
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/16054
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The PIC was not initialized, leading to hangs when booting
Linux as a payload. This error was hidden by both SeaBIOS
and GRUB due to both payloads initializing the PIC as a
matter of routine.
Change-Id: I9a3b9bd831d4dafdd0bb82ea023026a10fe7efca
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/16018
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Without this patch, eDP output is non-functional pre-graphics driver
regardless of payload (SeaBIOS, Tianocore) or video init method
(VBIOS, GOP driver) and once the standard Windows Intel HD graphics
driver is loaded.
Test: Boot Windows on peppy and auron_paine, install Intel HD
Graphics driver, observe functional eDP output with full video
acceleration.
Debugging method: adjust location of call to run VBIOS within
coreboot, observed that eDP output functional if the VBIOS is run
before the power optimizer lines, broken if run afterwards.
Change-Id: I6d8252e3de396887c84533e355f41693b9ea7514
Signed-off-by: Prabal Saha <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/15261
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
That only makes deviceid == 0 (because shifting a 16bit value by 16
bits, well...)
Change-Id: Iddca1de20760f92f70fe2d05886b488e5b48313d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1229558
Reviewed-on: https://review.coreboot.org/15960
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use the ACPI generator for creating the Chrome OS gpio
package. Each mainboard has its own list of Chrome OS
gpios that are fed into a helper to generate the ACPI
external OIPG package. Additionally, the common
chromeos.asl is now conditionally included based on
CONFIG_CHROMEOS.
Change-Id: I1d3d951964374a9d43521879d4c265fa513920d2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15909
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I195fd3a9c7fc07c35913342d2041e1ffef110466
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There are several different macros available to convert a PCI device and
function to a single 8 bit value. One is PCI_DEVFN and is defined in
device/pci_def.h. The other is DEV_FUNC and is defined in several intel
fsp based chipset implementations. In fsp_broadwell_de DEV_FUNC is even
used without being defined at all. This patch unifies the situation so
that only PCI_DEVFN is used.
Change-Id: Ia1c6d7f3683badc66d15053846936d88aa836632
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15546
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a universal hybrid graphics driver compatible with
all supported lenovo devices.
Hybrid graphics allows to connect the display panel to
either of one GPUs.
As there are only two GPUs one GPIO needs to be toggled.
In case the discrete GPU is activated the panel is routed to it.
On deactivation the panel is routed to the integrated
GPU.
On lenovo laptops the dGPU is always connected to PEG10 and it is
save to disable the PEG slot on dGPU deactivation.
Use common gpio.c for southbridge I82801IX.
Tested on Lenovo T520 using Nvidia NVS 5200m.
Removed Lenovo T430s from the list of supported devices,
as the T430s only supports "muxless Optimus".
Depends on change id:
Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
I8bd981c4696c174152cf41caefa6c083650d283a
Iaf0c2f941f2625a5547f9cba79da1b173da6f295
I994114734fa931926c34ed04305cddfbeb429b62
Change-Id: I9b80b31a7749bdf893ed3b772a6505c9f29a56d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
After we skip the bytes we send, the fifo pointer is at
right position. Reseting the fifo will change it to a
wrong place.
Please view the flashrom code, which tells the same thing.
https://code.coreboot.org/p/flashrom/source/tree/HEAD/trunk/sb600spi.c#L257
Change-Id: I31d487ce32c0d7ca3dead36d2b14611e73b1ad60
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/14955
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Having CFLAGS with -Os disables -falign-function, for
unlucky builds this may delay entry to ramstage by 600ms.
Build the low-level IO functions aligned with -O2 instead.
Change-Id: Ice6781666a0834f1e8e60a0c93048ac8472f27d9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14414
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Allow the platform to override the input clock for the UART by
implementing the routine uart_platform_refclk and setting the Kconfig
value UART_OVERRIDE_REFCLK. Provide a default uart_platform_refclk
routine which is disabled when UART_OVERRIDE_REFCLK is selected. This
works around ROMCC not supporting weak routines.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: If4afc45a828e5ba935fecb6d95b239625e912d14
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14612
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fixes two issues:
1. In (the unlikely) case that dev->chip_info is NULL, the output was
depending on an unknown value near the start of the address space.
2. Output for the secondary interface actually printed the primary
interface's configuration.
Change-Id: Id0f499a85e6e2410b4efd63baf7fffb2fcaa3103
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14361
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: Id6d11d1cea3ebde4adf63e3d98ac603d85591d5b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14331
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I61938b42c5aa75d1c7706a1c5ae45dace6704c86
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14330
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I9689bf4ccc5f639bd98d6277bdd27afe4bb4295b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14329
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I7a19ed8cf16b9424190800940d2b8ec1a96c5ce9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14328
Reviewed-by: Myles Watson <mylesgw@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The SB700 family has the ability to report the last reset
reason. This is useful in the context of handling MCEs
and recovering from fatal errors / sync floods.
Add a function to retrieve the last reset flags.
Change-Id: I754cb25e47bd9c1e4a29ecb6cb18017d1b7c3dc4
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14263
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The logic to enable reset on sync flood per RPR guidelines
somehow ended up guarded on the SATA AHCI setup. Unconditionally
enable reset on sync flood per the RPR.
Change-Id: I62d897010a8120aa14b4cb8d096bc4f2edc5f248
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14260
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
SP5100 devices are affected by an erratum that can lock up the
EHCI ports under certain conditions. Add an optional CMOS
option to enable a workaround at the expense of performance.
Change-Id: I305d23dfa50f10a3dcb5c731e8923305c8956dde
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14241
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
In the board status repository, there is trailing whitespace in the
coreboot log of the board ASUS KFSN4-DRE.
```
SATA S SATA P
```
Remove it, as it’s unnecessary.
Change-Id: I5c505eb7c734dca3fa18235e2bc0bc82b5b50b16
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/14175
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Use shared gpio code from common folder.
Remove the now unused bd82x6x/gpio.c.
Needs test on real hardware !
Change-Id: Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13616
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Use shared gpio code from common folder, except for
INTEL_LYNXPOINT_LP, which has it's own gpio code.
Needs test on real hardware !
Change-Id: Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13615
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The PCIe slot uses Message Signaled Interrupts (MSI) as the
IGD does and doesn't use hardware INT lines.
Adding the IRQ entry for PEG slot fixes a warning showing up in
GNU/Linux dmesg.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Change-Id: I5ac40e7bea9a659c6c89262aac4552bc8177a9e5
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13612
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use shared gpio code from common folder.
Bd82x6x's gpio.c and gpio.h is used by other southbridges
as well and will be removed once it is unused.
Change-Id: I8bd981c4696c174152cf41caefa6c083650d283a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13614
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add a common southbridge gpio code to reduce existing
duplicated code.
By adding it to ram-stage, GPIOs can be changed any time,
without the need of direct register access.
The files are based on bd82x6x and lynxpoint gpio.c.
Change-Id: Iaf0c2f941f2625a5547f9cba79da1b173da6f295
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12893
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On certain Winbond SuperIO devices, when a PS/2 mouse is not
present on the auxiliary channel both channels will cease to
function if the auxiliary channel is probed while the primary
channel is active. Therefore, knowledge of mouse presence
must be gathered by coreboot during early boot, and used to
enable or disable the auxiliary PS/2 port before control is
passed to the operating system.
Add auxiliary channel PS/2 device presence detect, and update
the Winbond W83667HG-A driver to flag the auxiliary channel as
disabled if no device was detected.
Change-Id: I76274493dacc9016ac6d0dff8548d1dc931c6266
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/13165
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
This tidies up the setting of the PCS register.
An assumption is made that bit 4 of this register is read-only,
which according to the ICH7 datasheet, it is.
Change-Id: Ia9b7d38a87e26236f6ebc951c169cae12b13139f
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13015
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
This just updates existing guard name comments on the header files
to match the actual #define name.
As a side effect, if there was no newline at the end of these files,
one was added.
Change-Id: Ia2cd8057f2b1ceb0fa1b946e85e0c16a327a04d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12900
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested on Intel D510MO
Before this patch, I was unable to get the SATA controller into AHCI
mode. That is, I could never see PCI ID 8086:27c1 appearing on the bus.
With sata_ahci set, controller now goes into AHCI mode and works. 8086:27c1
Tested on X60 with AHCI enabled 8086:27c5 (AHCI mode for mobile ich7)
No regressions detected.
Change-Id: I4a3eabb5773106a0825fa2f30ee400fbfe636c7f
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12923
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This continues what was done in commit a73b93157f
(tree: drop last paragraph of GPL copyright header)
Change-Id: Ifb8d2d13f7787657445817bdde8dc15df375e173
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12914
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code committed in GIT hash
* 1eaaa0 southbridge/amd/sr5650:Add MCFG ACPI table support
did not correctly locate the CPU MMCONFIG resource, leading to failures
with operating systems and firmware (e.g. SeaBIOS) when the PCI
extended configuration space option was activated.
Due to the southbridge routing not being set up, MMCONFIG accesses were
targetting DRAM and therefore the PCI devices were not being configured.
The failure normally manifests as a system hang immediately after PCI
configuration starts.
Search for the CPU MMCONFIG resource on all domains below the root
device.
Change-Id: I0df2f825fef2de46563db87af78d0609ab3d8c5a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12821
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Non-code flow assembly stubs do not have to be included in
bootblock.S, now that we have more freedom in bootblock linking.
Rather than bringing these stubs to the config system, just link them
in the bootblock.
Note that we cannot fully remove CHIPSET_BOOTBLOCK_INCLUDE at this
point, as some intel SOCs use this stub for code flow.
objdump -h build/cbfs/fallback/bootblock.debug on a few random boards
confirms that the appropriate sections are still included in the
final binary.
Change-Id: Id3f9ece14e399c1cc83090f407780c4a05a076f0
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: https://review.coreboot.org/11856
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Upcoming versions of IASL give a warning about unused methods. This
adds an operation after the read to use the local variable and avoid
the warning.
The warning can be completely disabled on the command line, but as it
can find real issues, my preference is to not do that.
Fixes warnings:
dsdt.aml 640: Store (CTMP, Local0)
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: If55bb8e03abb8861e1f2f08a8bcb1be8c9783afe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As the southbridge largely controls the PCI[e] configuration space
this patch moves the resource allocation from the northbridge
to the southbridge when the extended configuration space region
is enabled.
Change-Id: I0c4ba74ddcc727cd92b848d5d3240e6f9f392101
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12050
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
The SB600 code had the base address of the HPET hardcoded throughout.
It looks like the plan was to have it be updated in ACPI if needed,
but this wasn't ever implemented. The variable names being used to
do this update were the same, causing an IASL warning. Because of
this, the operation to update the HPET address actually did nothing.
This was fine, because it didn't actually need to be updated.
- Replace all that code with a #define.
- Add and update some comments in the same area.
Fixes IASL warning:
dsdt.aml 1505: Store(HPBA, HPBA)
Warning 3023 - ^ Duplicate value in list (Source is the
same as Target)
Change-Id: I9ba5fe226a4a464e0045ce7d3406898760df5e5a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12705
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
The ALIGN_CURRENT macro relied on a local variable name
as well as being defined in numerous compilation units.
Replace those instances with an acpi_align_current()
inline function.
Change-Id: Iab453f2eda1addefad8a1c37d265f917bd803202
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12707
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 640: If (CondRefOf (^GBUF, Local0)) {
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: Iddf46a4faab19019882847917397eee0614302b9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12695
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make the definitions of rules compliant with
others.
Change-Id: Ieef3a9c3fae5beaa1ea3e14e890cfb9145090c3b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/12685
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
At some point in the past disconnected PCIe bridges were completely
disabled to work around a hang on bridge probe. This hang was
resolved at some point, and the disconnected PCIe bridges should
be enabled to receive a bus number per the RPR.
This resolves a slew of warnings in the Linux boot log regarding
invalid bridge configurations for disconnected bridge devices.
Change-Id: Ic26e2d62ec5ddb9f22275c2afec7d560326263c7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12673
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It seems that no one add period in Kconfig.
Change-Id: Ie9c585a8e6f1a73036b92b2873dc19284d82dc39
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/12668
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Add a Kconfig option to set the firmware descriptor to allow EM100 use.
Change-Id: If5d7cd6ad671f0328ee5be0b5e660dbc837fcac3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12637
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kconfig symbols CONFIG_ACPI_INCLUDE_PMIO and CONFIG_ACPI_INCLUDE_GPIO
were never added to the coreboot codebase when the Rangeley code was
brought in from Sage. These symbols disabled ACPI code that was unused
because it caused dmesg warnings due to conflicts with drivers trying to
claim the same addresses as the ACPI code. Because it could be used on
some other platforms, it was left in instead of being completely
removed.
- Change the Kconfig symbol names to simple #defines in the mainboard
code.
- Add the #defines along with comments to the reference platform.
- Hook everything together in dsdt.asl
- Update new mainboard littleplains the same way.
Change-Id: I1f62157c6e447ea9b7207699572930e4711fc3e0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12552
Reviewed-by: David Guckian <david.guckian@intel.com>
Tested-by: build bot (Jenkins)
The folder southbridge/intel/common/firmware is already being included
so does not need to be added a second time here.
Change-Id: I60d795a60c772547278a5a5e0c9a023a93f90417
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Existence of requested PCI device was not checked when enabling
IDE mode on the SP5100. Fix incorrect PCI device ID and check
for device existence before attempting setup.
Change-Id: I726c355571b5c67c9a13995be2352601c03ab1e4
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12572
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The function delay in uart8250mem.c is not enough for hudson. I guess
there are some problems in lapic_timer(). I uploaded a patch to gerrit
to show the way to enable UART feature.
http://review.coreboot.org/#/c/12343/4
Currently the HUDSON_UART is unchecked by default. Select HUDSON_UART to
enable this feature.
The UART is test at BIOS stage.
Since it is not a standart UART device, the windows internal UART driver
doesnt support it. I guess we need a driver to use it on windows.
Change-Id: I4cec833cc2ff8069c82886837f7cbd4483ff11bb
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11749
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It works as an ICH7 on Intel D510MO mainboard
Change-Id: Ib8c76c001dffee8f93e3d6aa3156d4413b2e842a
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/12431
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The Bolton FCH needs different firmware files than the Hudson FCH.
A small patch to vendorcode is probably needed to make the XHCI controller work.
XHCI_DEVID in pci_devs.h is probably wrong for Hudson.
Change-Id: Ib81c0881979edcde717217dc89d8af415520d7e5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/9623
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. Use write_pci_int_table to write registers 0xC00/0xC01.
2. Add GPIO, I2C and UART interrupt according
"BKDG for AMD Family 15h Models 60h-6Fh Processors",
50742 Rev 3.01 - July 17, 2015
3. The interrupt valudes are moved from bettong/mptable.c.
All devices work in Windows 10.
Change-Id: Iad13bc02c84a5dfc7c24356436ac560f593304d7
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/11746
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
The Intel cave creek chipset needs to have port 80 routing configured
before any post codes can be sent to port 80h. Sending post codes out
before the routing is done will hang the system.
This patch allows us to disable the first couple of post codes that go
out before the routing can be configured.
The Kconfig symbol is selected by the cave creek chipset (fsp_i89xx).
Change-Id: I9bf41669ec32744f87a1ed2de011d31c72ea38da
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12422
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: York Yang <york.yang@intel.com>
On the ASUS KGPE-D16 it was noted that the pin straps did not properly
configure the lane director hardware, causing link training failure
on NIC B. Forcing coreboot to always reconfigure the lane director
on startup resolves this problem.
Change-Id: I5b78cef84960e0f42cc3e0406a7031d12d21f3ad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12014
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The SB700 silicon is somewhat buggy; if the links come up in an
incorrect state after POR the silicon cannot automatically recover.
If a disk fails to come online, reset the associated link and try
disk detection again.
Change-Id: I29051af5eca5d31b6aecc261e9a48028380eccb3
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In AHCI mode SeaBIOS randomly fails to detect disks (AHCI timeouts),
with the probability of a failure increasing with the number of disks
connected to the controller. Resetting the SATA controller appears to
show the true state of the underlying hardware, allowing the drive
detection code to attempt link renegotiation as needed.
Change-Id: Ib1f7c5f830a0cdba41cb6f5b05d759adee5ce369
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11998
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
SeaBIOS AHCI drive detection randomly fails for drives present
on the secondary channel of each AHCI SATA BAR. Forcing native
drive detection in AHCI mode resolves this issue.
Change-Id: I34eb1d5d3f2f8aefb749a4eeb911c1373d184938
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11997
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The AMD Register Programming Reference states that the user should
have the option to disable Active Link Power Management for two
reasons. First, some drives may not function correctly with the
ALPM implementation of the SP5100, and second there are some
situations where low latency access is more important than the
power savings created by using ALPM.
Allow the user to disable ALPM if desired.
Change-Id: I88055cbb4df4d7ba811cef7056c0a6ca2612fcb0
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11993
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds CC6 power save support to the AMD Family 15h
support code. As CC6 is a complex power saving state that
relies heavily on CPU, northbridge, and southbridge cooperation,
this patch alters significant amounts of code throughout the
tree simultaneously.
Allowing the CPU to enter CC6 allows the second level of turbo
boost to be reached, and also provides significant power savings
when the system is idle due to the complete core shutdown.
Change-Id: I44ce157cda97fb85f3e8f3d7262d4712b5410670
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11979
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Intel i89xx is a communications chipset that pairs with
Sandy(Ivy)bridge processors. It has a lot in common with
the bd82x6x chipset, but fewer devices and options.
Change-Id: I11bcd1edc80f72a1b2521def9be0d1bde5789a79
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12166
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This cast only hides errors in matching the API properly.
Change-Id: Ic396dfb572a50ac5ce5c1c83424e1f17f15bad1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/12270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ic3cdfa6086a45aa231aa817d5ef6998823589818
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7108
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Assign unique bus/dev/fn values for the I/O APIC and each HPET. The
values are taken from an example DMAR table. They are used as source-id
for MSI requests and as completer-id for reads from the device' MMIO
space [1, 2]. The former is usefull for source-id verfication during
interrupt remapping.
[1] Intel 6 Series Chipset and Intel C200 Series Chipset
Datasheet
Document-Number: 324645
[2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH)
Datasheet
Document-Number: 326776
Change-Id: Ib46f8cfb7d966dd1cf2b026f671bc45ffcc43d25
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12193
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The acpi_get_sleep_type function in SB700 ramstage is only needed
for boards / CPUs that require late CBMEM initialization.
Providing this function in early CBMEM-compatible boards breaks
building of the ACPI S3 code due to multiple definitions of
acpi_get_sleep_type.
Change-Id: Ieebc2640a586812e3e2bfd410987205d64147314
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12267
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
