Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Replace the use of the old device_t definition inside
southbridge/broadcom/bcm5785.
Change-Id: I091b07439ff918efa52cf8f8270484131fd0cec5
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16690
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
- Update lines to make them shorter than 80 chaacters
- Update using #defines from acpi_ivrs.h
Change-Id: I1bf6cdac00e28f5b0969fd8f98e37c66f8e43110
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16568
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Functionally, this should be roughly the same. The only real difference
should be removing the 4 bytes of padding from the end of the 4 byte
entries. The spec mentions a boundary for the 4 byte entries (which we
are ignoring), but doesn't mention a boundary for the 8 byte entries,
and I can't think of any other reason that the padding might be needed.
- Wrap long lines.
- Combine if statements to clean up indentation.
- Use #defines from acpi_ivrs.h to make commands easier to understand.
- Remove padding from 4 byte entries that made them 8 bytes in length.
- Set the pointer p at init, and clear the value at p if the device
we're looking at is enabled instead of setting p in every if statement.
- Look at the command type to update current and length.
- Treat malloc & free as if they were typical instead of coreboot
specific versions. Check to make sure the malloc worked and only
free on the last loop instead of every time.
Change-Id: I79dd5f9e930fad22a09d1af78f33c1d9a88b3bfe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16532
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Replace the use of the old device_t definition inside
southbridge/amd/agesa/hudson.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I39cd2afe5e2b6ee3963fd3e949eab1db9e986d71
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16401
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/ibexpeak.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ic569aada9301b37e73196872584e191d553acd86
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16408
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801gx.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ia257318a7068b54739f319bfbba35f2a07826940
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16370
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801ix.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Ibf20e6c08994b09d2a2e68a1a1d38a7a477493aa
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16403
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/via/vt8237r.
Change-Id: I9c1211e698ef35f56dd71c2c021dea680091c1ee
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16489
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/sis/sis966.
Change-Id: I9e731fedc6f21eaa2685f794ea2172eb4800628b
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16488
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/nvidia/mcp55.
Change-Id: I98ac468940eaf6c456fa95540ec3e718edfe26a7
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/nvidia/ck801.
Change-Id: I43d4d2175f0b6b9e7e2e6fe665ba3d99d792427c
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16486
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb800.
Change-Id: I488cde4504128331106f50b34869905e30f5ab83
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16480
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb700.
Change-Id: I44b0be2070719066dd18bbf2882c417caef5d8b2
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16479
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/sb600.
Change-Id: I0227cc0c611324f513f8170c9d8819a88af39b39
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16478
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/rs780.
Change-Id: Ia9929baeec7423e9e2f06324038ddfbec006beb7
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16477
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/rs690.
Change-Id: Ief43393f62312bfe82e960faf56b1e2ec048f4ff
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16476
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/pi/hudson.
Change-Id: I8b22a8d9f0e90afaf0f218c5c0924a78883b7498
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/cimx.
Change-Id: Ibe2766b956b0ca02be63621aee9a230b16d9923b
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16474
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/amd/amd8111.
Change-Id: I76cdc32171b7ce819b53c534b3a5e57e9dd5f3dd
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16473
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801dx.
Change-Id: Ic08a23f672f8b5e40b837d49a9475d52c728a306
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16485
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82801ax.
Change-Id: I46f0cc92e1034f045988b42df7246f5d0c8d24fc
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16484
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i82371eb.
Change-Id: Ie15a656c817a2ffe0f44ee3a89659d138a1bf212
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16483
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/i3100.
Change-Id: Ic9616d5135cfb7206e086e51aaf82eb66540c4bb
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16482
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/fsp_rangeley.
Change-Id: I6665f85c74eb3e37d78f6eecbec977dc21a5ad12
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16481
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Defining this OpRegion for SMBus controller prevents linux kernel
driver i2c-i801 from registering SMBus under sysfs, with following
error in dmesg:
ACPI Warning: SystemIO range .. conflicts with OpRegion .. (\_SB.PCI0.SBUS.SMBI)
Solution taken from intel/bd82x6x. Worth noting we do not
define ENABLE_SMBUS_METHODS anywhere currently.
Removed remaining reference to HSTS from GETAC P470.
Change-Id: I7c13d344b0343387681b46019cc5061b1435b46b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16266
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
The field that was previously named 'efr' is actually the iommu feature
info field. The efr field is a 64-bit field that is only present in
type 11h or type 40h headers that follows the iommu feature info field.
Change-Id: I62c158a258d43bf1912fedd63cc31b80321a27c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16508
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Replace the use of the old device_t definition inside
southbridge/intel/bd82x6x.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I7166bfab7904f80b745855d3bbcfb910cbc89f56
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16407
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The recent changes to this file from commit 6e5421d2
(sb/amd/sb700: Add option to increase SPI speed to 33MHz)
were accidentally removed in a code cleanup patch:
commit ba28e8d7 (src/southbridge: Code formating).
Change-Id: I6cf3e8f29d5c0384d35637f35e051be40318d20f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16384
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Tested-by: build bot (Jenkins)
Some SB700-based systems and ROMs support high speed (33MHz) SPI
access instead of the power-on default 16.5MHz. Add an option
to enable high speed SPI access in the bootblock, and set the
default value to Disabled. This greatly decreases boot time on
SB700-based systems, especiall when a large payload is in use.
On a KGPE-D16 with a Petitboot (Linux + initramfs) payload, the
command prompt was accessible within 20 seconds of power on, which
incidentally is faster than the proprietary BIOS on the same machine
could even reach the GRUB bootloader.
Change-Id: Iadbd9bb611754262ef75a5e5a6ee4390a46e45cf
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Test: Booted KGPE-D16 with Linux payload
Reviewed-on: https://review.coreboot.org/16306
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Since RTC is now a Kconfig ensure RTC is selected on the
x86 chipsets which are in Chrome OS devices. This allows
the eventlog to have proper timestamps instead of all
zeros.
BUG=chrome-os-partner:55993
Change-Id: I24ae7d9b3bf43a5791d4dc04aae018ce17fda72b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Port commit e08493 to the SB700 platform
Change-Id: Ie18c6cc0ccb31a0d16a80fcb4c2e147c19e228fe
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/16054
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The PIC was not initialized, leading to hangs when booting
Linux as a payload. This error was hidden by both SeaBIOS
and GRUB due to both payloads initializing the PIC as a
matter of routine.
Change-Id: I9a3b9bd831d4dafdd0bb82ea023026a10fe7efca
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/16018
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Without this patch, eDP output is non-functional pre-graphics driver
regardless of payload (SeaBIOS, Tianocore) or video init method
(VBIOS, GOP driver) and once the standard Windows Intel HD graphics
driver is loaded.
Test: Boot Windows on peppy and auron_paine, install Intel HD
Graphics driver, observe functional eDP output with full video
acceleration.
Debugging method: adjust location of call to run VBIOS within
coreboot, observed that eDP output functional if the VBIOS is run
before the power optimizer lines, broken if run afterwards.
Change-Id: I6d8252e3de396887c84533e355f41693b9ea7514
Signed-off-by: Prabal Saha <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/15261
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
That only makes deviceid == 0 (because shifting a 16bit value by 16
bits, well...)
Change-Id: Iddca1de20760f92f70fe2d05886b488e5b48313d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1229558
Reviewed-on: https://review.coreboot.org/15960
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use the ACPI generator for creating the Chrome OS gpio
package. Each mainboard has its own list of Chrome OS
gpios that are fed into a helper to generate the ACPI
external OIPG package. Additionally, the common
chromeos.asl is now conditionally included based on
CONFIG_CHROMEOS.
Change-Id: I1d3d951964374a9d43521879d4c265fa513920d2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15909
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I195fd3a9c7fc07c35913342d2041e1ffef110466
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There are several different macros available to convert a PCI device and
function to a single 8 bit value. One is PCI_DEVFN and is defined in
device/pci_def.h. The other is DEV_FUNC and is defined in several intel
fsp based chipset implementations. In fsp_broadwell_de DEV_FUNC is even
used without being defined at all. This patch unifies the situation so
that only PCI_DEVFN is used.
Change-Id: Ia1c6d7f3683badc66d15053846936d88aa836632
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15546
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a universal hybrid graphics driver compatible with
all supported lenovo devices.
Hybrid graphics allows to connect the display panel to
either of one GPUs.
As there are only two GPUs one GPIO needs to be toggled.
In case the discrete GPU is activated the panel is routed to it.
On deactivation the panel is routed to the integrated
GPU.
On lenovo laptops the dGPU is always connected to PEG10 and it is
save to disable the PEG slot on dGPU deactivation.
Use common gpio.c for southbridge I82801IX.
Tested on Lenovo T520 using Nvidia NVS 5200m.
Removed Lenovo T430s from the list of supported devices,
as the T430s only supports "muxless Optimus".
Depends on change id:
Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
I8bd981c4696c174152cf41caefa6c083650d283a
Iaf0c2f941f2625a5547f9cba79da1b173da6f295
I994114734fa931926c34ed04305cddfbeb429b62
Change-Id: I9b80b31a7749bdf893ed3b772a6505c9f29a56d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
After we skip the bytes we send, the fifo pointer is at
right position. Reseting the fifo will change it to a
wrong place.
Please view the flashrom code, which tells the same thing.
https://code.coreboot.org/p/flashrom/source/tree/HEAD/trunk/sb600spi.c#L257
Change-Id: I31d487ce32c0d7ca3dead36d2b14611e73b1ad60
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/14955
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Having CFLAGS with -Os disables -falign-function, for
unlucky builds this may delay entry to ramstage by 600ms.
Build the low-level IO functions aligned with -O2 instead.
Change-Id: Ice6781666a0834f1e8e60a0c93048ac8472f27d9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14414
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Allow the platform to override the input clock for the UART by
implementing the routine uart_platform_refclk and setting the Kconfig
value UART_OVERRIDE_REFCLK. Provide a default uart_platform_refclk
routine which is disabled when UART_OVERRIDE_REFCLK is selected. This
works around ROMCC not supporting weak routines.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: If4afc45a828e5ba935fecb6d95b239625e912d14
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14612
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fixes two issues:
1. In (the unlikely) case that dev->chip_info is NULL, the output was
depending on an unknown value near the start of the address space.
2. Output for the secondary interface actually printed the primary
interface's configuration.
Change-Id: Id0f499a85e6e2410b4efd63baf7fffb2fcaa3103
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14361
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: Id6d11d1cea3ebde4adf63e3d98ac603d85591d5b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14331
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I61938b42c5aa75d1c7706a1c5ae45dace6704c86
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14330
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I9689bf4ccc5f639bd98d6277bdd27afe4bb4295b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14329
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I7a19ed8cf16b9424190800940d2b8ec1a96c5ce9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14328
Reviewed-by: Myles Watson <mylesgw@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The SB700 family has the ability to report the last reset
reason. This is useful in the context of handling MCEs
and recovering from fatal errors / sync floods.
Add a function to retrieve the last reset flags.
Change-Id: I754cb25e47bd9c1e4a29ecb6cb18017d1b7c3dc4
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14263
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The logic to enable reset on sync flood per RPR guidelines
somehow ended up guarded on the SATA AHCI setup. Unconditionally
enable reset on sync flood per the RPR.
Change-Id: I62d897010a8120aa14b4cb8d096bc4f2edc5f248
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14260
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
SP5100 devices are affected by an erratum that can lock up the
EHCI ports under certain conditions. Add an optional CMOS
option to enable a workaround at the expense of performance.
Change-Id: I305d23dfa50f10a3dcb5c731e8923305c8956dde
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14241
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
In the board status repository, there is trailing whitespace in the
coreboot log of the board ASUS KFSN4-DRE.
```
SATA S SATA P
```
Remove it, as it’s unnecessary.
Change-Id: I5c505eb7c734dca3fa18235e2bc0bc82b5b50b16
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/14175
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Use shared gpio code from common folder.
Remove the now unused bd82x6x/gpio.c.
Needs test on real hardware !
Change-Id: Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13616
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Use shared gpio code from common folder, except for
INTEL_LYNXPOINT_LP, which has it's own gpio code.
Needs test on real hardware !
Change-Id: Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13615
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The PCIe slot uses Message Signaled Interrupts (MSI) as the
IGD does and doesn't use hardware INT lines.
Adding the IRQ entry for PEG slot fixes a warning showing up in
GNU/Linux dmesg.
Test system:
* Intel IvyBridge
* Gigabyte GA-B75M-D3H
Change-Id: I5ac40e7bea9a659c6c89262aac4552bc8177a9e5
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13612
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use shared gpio code from common folder.
Bd82x6x's gpio.c and gpio.h is used by other southbridges
as well and will be removed once it is unused.
Change-Id: I8bd981c4696c174152cf41caefa6c083650d283a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13614
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add a common southbridge gpio code to reduce existing
duplicated code.
By adding it to ram-stage, GPIOs can be changed any time,
without the need of direct register access.
The files are based on bd82x6x and lynxpoint gpio.c.
Change-Id: Iaf0c2f941f2625a5547f9cba79da1b173da6f295
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12893
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On certain Winbond SuperIO devices, when a PS/2 mouse is not
present on the auxiliary channel both channels will cease to
function if the auxiliary channel is probed while the primary
channel is active. Therefore, knowledge of mouse presence
must be gathered by coreboot during early boot, and used to
enable or disable the auxiliary PS/2 port before control is
passed to the operating system.
Add auxiliary channel PS/2 device presence detect, and update
the Winbond W83667HG-A driver to flag the auxiliary channel as
disabled if no device was detected.
Change-Id: I76274493dacc9016ac6d0dff8548d1dc931c6266
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/13165
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
This tidies up the setting of the PCS register.
An assumption is made that bit 4 of this register is read-only,
which according to the ICH7 datasheet, it is.
Change-Id: Ia9b7d38a87e26236f6ebc951c169cae12b13139f
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13015
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
This just updates existing guard name comments on the header files
to match the actual #define name.
As a side effect, if there was no newline at the end of these files,
one was added.
Change-Id: Ia2cd8057f2b1ceb0fa1b946e85e0c16a327a04d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12900
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested on Intel D510MO
Before this patch, I was unable to get the SATA controller into AHCI
mode. That is, I could never see PCI ID 8086:27c1 appearing on the bus.
With sata_ahci set, controller now goes into AHCI mode and works. 8086:27c1
Tested on X60 with AHCI enabled 8086:27c5 (AHCI mode for mobile ich7)
No regressions detected.
Change-Id: I4a3eabb5773106a0825fa2f30ee400fbfe636c7f
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12923
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This continues what was done in commit a73b93157f
(tree: drop last paragraph of GPL copyright header)
Change-Id: Ifb8d2d13f7787657445817bdde8dc15df375e173
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12914
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code committed in GIT hash
* 1eaaa0 southbridge/amd/sr5650:Add MCFG ACPI table support
did not correctly locate the CPU MMCONFIG resource, leading to failures
with operating systems and firmware (e.g. SeaBIOS) when the PCI
extended configuration space option was activated.
Due to the southbridge routing not being set up, MMCONFIG accesses were
targetting DRAM and therefore the PCI devices were not being configured.
The failure normally manifests as a system hang immediately after PCI
configuration starts.
Search for the CPU MMCONFIG resource on all domains below the root
device.
Change-Id: I0df2f825fef2de46563db87af78d0609ab3d8c5a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12821
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Non-code flow assembly stubs do not have to be included in
bootblock.S, now that we have more freedom in bootblock linking.
Rather than bringing these stubs to the config system, just link them
in the bootblock.
Note that we cannot fully remove CHIPSET_BOOTBLOCK_INCLUDE at this
point, as some intel SOCs use this stub for code flow.
objdump -h build/cbfs/fallback/bootblock.debug on a few random boards
confirms that the appropriate sections are still included in the
final binary.
Change-Id: Id3f9ece14e399c1cc83090f407780c4a05a076f0
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: https://review.coreboot.org/11856
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Upcoming versions of IASL give a warning about unused methods. This
adds an operation after the read to use the local variable and avoid
the warning.
The warning can be completely disabled on the command line, but as it
can find real issues, my preference is to not do that.
Fixes warnings:
dsdt.aml 640: Store (CTMP, Local0)
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: If55bb8e03abb8861e1f2f08a8bcb1be8c9783afe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As the southbridge largely controls the PCI[e] configuration space
this patch moves the resource allocation from the northbridge
to the southbridge when the extended configuration space region
is enabled.
Change-Id: I0c4ba74ddcc727cd92b848d5d3240e6f9f392101
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12050
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
The SB600 code had the base address of the HPET hardcoded throughout.
It looks like the plan was to have it be updated in ACPI if needed,
but this wasn't ever implemented. The variable names being used to
do this update were the same, causing an IASL warning. Because of
this, the operation to update the HPET address actually did nothing.
This was fine, because it didn't actually need to be updated.
- Replace all that code with a #define.
- Add and update some comments in the same area.
Fixes IASL warning:
dsdt.aml 1505: Store(HPBA, HPBA)
Warning 3023 - ^ Duplicate value in list (Source is the
same as Target)
Change-Id: I9ba5fe226a4a464e0045ce7d3406898760df5e5a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12705
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
The ALIGN_CURRENT macro relied on a local variable name
as well as being defined in numerous compilation units.
Replace those instances with an acpi_align_current()
inline function.
Change-Id: Iab453f2eda1addefad8a1c37d265f917bd803202
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12707
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 640: If (CondRefOf (^GBUF, Local0)) {
Warning 3144 - Method Local is set but never used ^ (Local0)
Change-Id: Iddf46a4faab19019882847917397eee0614302b9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12695
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make the definitions of rules compliant with
others.
Change-Id: Ieef3a9c3fae5beaa1ea3e14e890cfb9145090c3b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/12685
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
At some point in the past disconnected PCIe bridges were completely
disabled to work around a hang on bridge probe. This hang was
resolved at some point, and the disconnected PCIe bridges should
be enabled to receive a bus number per the RPR.
This resolves a slew of warnings in the Linux boot log regarding
invalid bridge configurations for disconnected bridge devices.
Change-Id: Ic26e2d62ec5ddb9f22275c2afec7d560326263c7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12673
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It seems that no one add period in Kconfig.
Change-Id: Ie9c585a8e6f1a73036b92b2873dc19284d82dc39
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/12668
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Add a Kconfig option to set the firmware descriptor to allow EM100 use.
Change-Id: If5d7cd6ad671f0328ee5be0b5e660dbc837fcac3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12637
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kconfig symbols CONFIG_ACPI_INCLUDE_PMIO and CONFIG_ACPI_INCLUDE_GPIO
were never added to the coreboot codebase when the Rangeley code was
brought in from Sage. These symbols disabled ACPI code that was unused
because it caused dmesg warnings due to conflicts with drivers trying to
claim the same addresses as the ACPI code. Because it could be used on
some other platforms, it was left in instead of being completely
removed.
- Change the Kconfig symbol names to simple #defines in the mainboard
code.
- Add the #defines along with comments to the reference platform.
- Hook everything together in dsdt.asl
- Update new mainboard littleplains the same way.
Change-Id: I1f62157c6e447ea9b7207699572930e4711fc3e0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12552
Reviewed-by: David Guckian <david.guckian@intel.com>
Tested-by: build bot (Jenkins)
The folder southbridge/intel/common/firmware is already being included
so does not need to be added a second time here.
Change-Id: I60d795a60c772547278a5a5e0c9a023a93f90417
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Existence of requested PCI device was not checked when enabling
IDE mode on the SP5100. Fix incorrect PCI device ID and check
for device existence before attempting setup.
Change-Id: I726c355571b5c67c9a13995be2352601c03ab1e4
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/12572
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The function delay in uart8250mem.c is not enough for hudson. I guess
there are some problems in lapic_timer(). I uploaded a patch to gerrit
to show the way to enable UART feature.
http://review.coreboot.org/#/c/12343/4
Currently the HUDSON_UART is unchecked by default. Select HUDSON_UART to
enable this feature.
The UART is test at BIOS stage.
Since it is not a standart UART device, the windows internal UART driver
doesnt support it. I guess we need a driver to use it on windows.
Change-Id: I4cec833cc2ff8069c82886837f7cbd4483ff11bb
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11749
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It works as an ICH7 on Intel D510MO mainboard
Change-Id: Ib8c76c001dffee8f93e3d6aa3156d4413b2e842a
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/12431
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The Bolton FCH needs different firmware files than the Hudson FCH.
A small patch to vendorcode is probably needed to make the XHCI controller work.
XHCI_DEVID in pci_devs.h is probably wrong for Hudson.
Change-Id: Ib81c0881979edcde717217dc89d8af415520d7e5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/9623
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. Use write_pci_int_table to write registers 0xC00/0xC01.
2. Add GPIO, I2C and UART interrupt according
"BKDG for AMD Family 15h Models 60h-6Fh Processors",
50742 Rev 3.01 - July 17, 2015
3. The interrupt valudes are moved from bettong/mptable.c.
All devices work in Windows 10.
Change-Id: Iad13bc02c84a5dfc7c24356436ac560f593304d7
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/11746
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
The Intel cave creek chipset needs to have port 80 routing configured
before any post codes can be sent to port 80h. Sending post codes out
before the routing is done will hang the system.
This patch allows us to disable the first couple of post codes that go
out before the routing can be configured.
The Kconfig symbol is selected by the cave creek chipset (fsp_i89xx).
Change-Id: I9bf41669ec32744f87a1ed2de011d31c72ea38da
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12422
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: York Yang <york.yang@intel.com>
On the ASUS KGPE-D16 it was noted that the pin straps did not properly
configure the lane director hardware, causing link training failure
on NIC B. Forcing coreboot to always reconfigure the lane director
on startup resolves this problem.
Change-Id: I5b78cef84960e0f42cc3e0406a7031d12d21f3ad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12014
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The SB700 silicon is somewhat buggy; if the links come up in an
incorrect state after POR the silicon cannot automatically recover.
If a disk fails to come online, reset the associated link and try
disk detection again.
Change-Id: I29051af5eca5d31b6aecc261e9a48028380eccb3
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In AHCI mode SeaBIOS randomly fails to detect disks (AHCI timeouts),
with the probability of a failure increasing with the number of disks
connected to the controller. Resetting the SATA controller appears to
show the true state of the underlying hardware, allowing the drive
detection code to attempt link renegotiation as needed.
Change-Id: Ib1f7c5f830a0cdba41cb6f5b05d759adee5ce369
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11998
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
SeaBIOS AHCI drive detection randomly fails for drives present
on the secondary channel of each AHCI SATA BAR. Forcing native
drive detection in AHCI mode resolves this issue.
Change-Id: I34eb1d5d3f2f8aefb749a4eeb911c1373d184938
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11997
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The AMD Register Programming Reference states that the user should
have the option to disable Active Link Power Management for two
reasons. First, some drives may not function correctly with the
ALPM implementation of the SP5100, and second there are some
situations where low latency access is more important than the
power savings created by using ALPM.
Allow the user to disable ALPM if desired.
Change-Id: I88055cbb4df4d7ba811cef7056c0a6ca2612fcb0
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11993
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds CC6 power save support to the AMD Family 15h
support code. As CC6 is a complex power saving state that
relies heavily on CPU, northbridge, and southbridge cooperation,
this patch alters significant amounts of code throughout the
tree simultaneously.
Allowing the CPU to enter CC6 allows the second level of turbo
boost to be reached, and also provides significant power savings
when the system is idle due to the complete core shutdown.
Change-Id: I44ce157cda97fb85f3e8f3d7262d4712b5410670
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11979
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Intel i89xx is a communications chipset that pairs with
Sandy(Ivy)bridge processors. It has a lot in common with
the bd82x6x chipset, but fewer devices and options.
Change-Id: I11bcd1edc80f72a1b2521def9be0d1bde5789a79
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12166
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This cast only hides errors in matching the API properly.
Change-Id: Ic396dfb572a50ac5ce5c1c83424e1f17f15bad1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/12270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ic3cdfa6086a45aa231aa817d5ef6998823589818
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7108
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Assign unique bus/dev/fn values for the I/O APIC and each HPET. The
values are taken from an example DMAR table. They are used as source-id
for MSI requests and as completer-id for reads from the device' MMIO
space [1, 2]. The former is usefull for source-id verfication during
interrupt remapping.
[1] Intel 6 Series Chipset and Intel C200 Series Chipset
Datasheet
Document-Number: 324645
[2] Intel 7 Series / C216 Chipset Family Platform Controller Hub (PCH)
Datasheet
Document-Number: 326776
Change-Id: Ib46f8cfb7d966dd1cf2b026f671bc45ffcc43d25
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12193
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The acpi_get_sleep_type function in SB700 ramstage is only needed
for boards / CPUs that require late CBMEM initialization.
Providing this function in early CBMEM-compatible boards breaks
building of the ACPI S3 code due to multiple definitions of
acpi_get_sleep_type.
Change-Id: Ieebc2640a586812e3e2bfd410987205d64147314
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12267
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All mainboards using this southbridge have been removed from
the tree already.
Change-Id: I4398ef1e270bd0f36c5dd1c6ec3bfec6c2c091e6
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12238
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All boards using this southbridge have been removed from
the tree already.
Change-Id: I08269931d845d1f57b34174238bcce245ad77894
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a comment explaining what `abcfg_reg(0xc0, 0x01FF, 0x0F4)` does.
This is a follow-up for commit 24501cae (AMD cimx/sb800: Initially
enable all GPP ports).
Change-Id: I5ac263ee088d36a7f7a2d03c1454ed647faa7147
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/12190
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
LPC decodes were not enabled, leading to a failure of POST 80 cards
and similar debugging devices. Enable the relevant LPC decodes
to allow debugging.
Additionally, the SMBUS controllers were not properly set up.
Enable both the primary and auxiliary controllers.
Finally, K10 and higher CPUs were hanging during boot due to
a misconfigued IOAPIC. Properly configure the IOAPIC.
Change-Id: I9ffb6542ce445ac971fb81f4f554e7f1313e6a98
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12177
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are needed for the hardware-sequencing function of the PCH SPI
interface. Values are specific to the flash chip used on a board.
Change-Id: Id06766b4bac2686406bc09b8afa02f311f40dee7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11798
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Do not hardcode the CPU downstream non-posted request limit; the
value of this register is CPU family specific and is set appropriately
in the corresponding CPU driver code.
Change-Id: I432b942f114243cba23c9a8d916cf6d07bc4740b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11935
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This chip is still being used and should not have been deleted. It's
a current intel chip, and doesn't even require an ME binary.
This reverts commit 959478a763.
Change-Id: I78594871f87af6e882a245077b59727e15f8021a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11860
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The x86 bootblock linking is a mess. The bootblock is treated in
a very special manner, and never received the update to link-time
garbage collection.
On newer x86 platforms, the boot media is no longer memory-mapped.
That means we need to do a lot more setup in the bootblock. ROMCC is
unsuitable for this task, and walkcbfs only works on memory-mapped
CBFS. We need to revise the x86 bootflow for this new case.
The approach this patch series takes is to perform CAR setup in the
bootblock, and load the following stage (either romstage or verstage)
from the boot media. This approach is not new, but has been done on
our ARM ports for years.
Since we will be adding .c files to the bootblock, it is prudent to
use link-time garbage collection. This is also consistent to how we
do things on other architectures. Unification FTW!
Change-Id: I16b78456df56e0053984a9aca9367e2542adfdc9
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11781
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The EM100Pro allows the debug console to be sent over the SPI bus.
This is not yet working in romstage due to the use of static variables
in the SPI driver code. It is also not working on chipsets that have
SPI write buffers of less than 10 characters due to the 9 byte
command/header length specified by the EM100 protocol.
While this currently works only with the EM100, it seems like it would
be useful on any logic analyzer with SPI debug - just filter on command
bytes of 0x11.
Change-Id: Icd42ccd96cab0a10a4e70f4b02ecf9de8169564b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
mohonpeak is the reference board for Rangeley. I doubt anyone uses it
or cares about it. We jokingly refer to it as "Moron Peak". It's code
with no known users, so we shouldn't be hauling it around for the
eventuality that someone might use it in the future.
Change-Id: Id3c9fc39e1b98707d96a95f2a914de6bbb31c615
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11790
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
We already have two other code paths for this silicon. Maintaining the
FSP path as well doesn't make much sense. There was only one board to
use this code, and it's a reference board that I doubt anyone still
owns or uses.
Change-Id: I4fcfa6c56448416624fd26418df19b354eb72f39
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11789
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
This is a sad story. We have three different code paths for
sandybridge and ivybridge: proper native path, google MRC path, and,
everyone's favorite: Intel FSP path. For the purpose of this patch,
the FSP path lives in its own little world, and doesn't concern us.
Since MRC was first, when native files and variables were added, they
were suffixed with "_native" to separate them from the existing code.
This can cause confusion, as the suffix might make the native files
seem parasitical.
This has been bothering me for many months. MRC should be the
parasitical path, especially since we fully support native init, and
it works more reliably, on a wider range of hardware. There have been
a few board ports that never made it to coreboot.org because MRC would
hang.
gigabyte/ga-b75m-d3h is a prime example: it did not work with MRC, so
the effort was abandoned at first. Once the native path became
available, the effort was restarted and the board is now supported.
In honor of the hackers and pioneers who made the native code
possible, rename things so that their effort is the first class
citizen.
Change-Id: Ic86cee5e00bf7f598716d3d15d1ea81ca673932f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11788
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Add some missing devices to device tree and header.
Remove the obsolete devices.
Change-Id: Ieeca06c68fe8c8eef6be4fab43193b898aebf013
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11378
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of selecting the Kconfig option and adding the subdir
entry within each chipset auto include the common/firmware
directory as it's guarded by HAVE_INTEL_FIRMWARE.
BUG=chrome-os-partner:43462
BRANCH=None
TEST=Built glados.
Change-Id: I166db67c41b16c4d9f0116abce00940514539fa5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11734
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
While the romstage code flow is not consistent across all
mainboards/chipsets there is only one way of running ramstage
from romstage -- run_ramstage(). Move the
timestamp_add_now(TS_END_ROMSTAGE) to be within run_ramstage().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados. TS_END_ROMSTAGE still present in
timestamp table.
Change-Id: I4b584e274ce2107e83ca6425491fdc71a138e82c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11700
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This switches the final 4 Intel platforms that use ME firmware from
using code specific to the platform to the common IFD Kconfig and
Makefile.
braswell, broadwell, bd82x6x (cougar point & panther point) and ibexpeak
Change-Id: Id3bec6dbe2e1a8a90f51d9378150dbb44258b596
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10876
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The build system was previously determining the flow
and linking scripts bootblock code by the order of files
added to the bootblock_inc bootblock-y variables.Those
files were then concatenated together and built by a myriad of
make rules.
Now bootblock.S and bootblock.ld is added so that bootblock
can be built and linked using the default build rules.
CHIPSET_BOOTBLOCK_INCLUDE is introduced in order to allow the
chipset code to place include files in the path of the bootblock
program -- a replacement for the chipset_bootblock_inc
make variable.
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built vortex, rambi, and some asus boards.
Change-Id: Ida4571cbe6eed65e77ade98b8d9ad056353c53f9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11495
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
coreboot has no CREDITS file.
Change-Id: Iaa4686979ba1385b00ad1dbb6ea91e58f5014384
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11514
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The BOOT_STATE_INIT_ENTRY macro can only be used in ramstage, however
the current state of the header meant bad build errors in non-ramstage.
Therefore, people had to #ifdef in the source. Remove that requirement.
Change-Id: I8755fc68bbaca6b72fbe8b4db4bcc1ccb35622bd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11492
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add support to the Intel common firmware Kconfig and Makefile.inc to
allow the Gigabit Ethernet (GBE) blob to be added to the final
binary.
Change-Id: Id5fab3061874dad759750b67d3339eb8c99a62d6
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10875
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Drop old incomplete, broken and hardcoded sata.asl properties.
The new sata acpi generator only needs a proper defined device.
Change-Id: Id3eca5551a070dfdd6fa674e1d5b6627e28ab5a7
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9710
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Drop old incomplete, broken and hardcoded sata.asl properties.
The new sata acpi generator only needs a proper defined device.
Change-Id: I2be76097ebd27f2529e3fbbecefd314a0eea3cb0
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9709
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The location of the AMD ROMSIG binary was being checked and warnings
were being printed even when the ROMSIG file wasn't being used.
These false warnings are avoided by moving the warnings into the
block where the CBFS file for the ROMSIG is generated.
Change-Id: Ie44a2ad97ff3b15df6dc9b8166992de6ed837997
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11161
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When the user's primary group contains a space ls -l and awk get the
wrong value for the file size. This results in padding the
coreboot_psp_directory_combine_pubkey.bin file too much which ultimately
means RtmPubSigned.key can not be placed at the necessary offset.
Changing from ls -l to ls -ln seemed like the most minimal,
POSIX-friendly way to effect this change.
Change-Id: Icbeaad476753924626adb6de53dc9a30052d91a6
Signed-off-by: Dan Christensen <opello@opello.org>
Reviewed-on: http://review.coreboot.org/11242
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As acpi_write_hpet() uses CONFIG_HPET_ADDRESS in the HPET table we
need to use CONFIG_HPET_ADDRESS when assigning it to the device.
Change-Id: I656f917658f1c1717bb3653fa048a6d36fca2454
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10925
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some FSF addresses found their way back into our tree.
Change-Id: I34b465fc78734d818eca1d6962a1e62bf9d6e7f3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/11145
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Add functions to support fan control.
2. When IMC firmware is added, the current firmwares' layout
cause build error. There is not enough space to add some firmwares,
so HUDSON_PSP_OFFSET is added to fix this problem.
Change-Id: Ie470a88cb9da256d9f72ea56bf268c15df195784
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10720
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Based on the observations that AMD Fam10h with both Nvidia CK804 (Asus
KFSN4-DRE) and MCP55 (Sun Ultra 40 M2) need to avoid adjusting the LPC
bridge register 0x78 (particularly the 0x7b byte) to get to ramstage:
Assume that there's something about this register that adjusting it the
way we do for K8 is something that can/should be universally avoided on
all Fam10h systems with these chipsets.
Change-Id: I1eceeb20ecaefef4c61c11e19d1f5a59f91a0a2f
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10984
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Fix typo. Use the correct math helper int-lt.
Change-Id: Ia5e722020c75595dfcfb853ea8238fb8391f9a04
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10980
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new attributes increase the header size, breaking this assumption.
Change-Id: Ib23862f27650b39133deafb74a24327b098b6e86
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10942
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Should fix regression in HDA verb setup on nvidia mcp55 and intel sch
southbridges. The mcp55 code could not find the mainboard's verb table
because the table was not even being compiled in. The sch boards appeared
to have the same issue.
Intel broadwell and fsp_bd82x6x seemed to have not gotten the boilerplate
shrink, so apply it to those too.
Followup-to: Ib3e09644c0ee71aacb067adaa85653d151b52078
(azalia: Shrink boilerplate)
Change-Id: If7aae69f5171db67055ffe220bdff392caaa5d9f
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10826
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I08f7251f8fc42b9028b1fdb830546f9922ef43aa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: YongGon Kim <ilios86@gmail.com>
Reviewed-on: http://review.coreboot.org/10914
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
For hex and int type kconfig symbols, IS_ENABLED() doesn't work. Instead
check to make sure they're defined and not zero. In some cases, zero
might be a valid value, but it didn't look like zero was valid in these
cases.
Change-Id: Ib51fb31b3babffbf25ed3ae4ed11a2dc9a4be709
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10886
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Platforms selecting the HUDSON_DISABLE_IMC symbol were showing the
warning:
warning: (BOARD_SPECIFIC_OPTIONS && BOARD_SPECIFIC_OPTIONS &&
CPU_AMD_AGESA_BINARY_PI) selects HUDSON_DISABLE_IMC which has unmet
direct dependencies (SOUTHBRIDGE_AMD_PI_AVALON ||
SOUTHBRIDGE_AMD_PI_BOLTON || SOUTHBRIDGE_AMD_PI_KERN)
By moving the definition of the symbol outside of the if block
and removing the default n, we can get rid of the warning without
changing the value for any platform.
Change-Id: I5c1bdfbcf3c5c44ee05b8c5e679f6854d784d8dc
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10680
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Kconfigs symbols of type bool are always defined, and can be tested with
the IS_ENABLED() macro.
symbol type except string.
Change-Id: Ic4ba79f519ee2a53d39c10859bbfa9c32015b19d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Display a warning if CONFIG_HUDSON_FWM_POSITION is not inside CBFS.
This can be extended to other Kconfig values for CBFS.
Change-Id: I2423f7b361dda8aac5dab409fa7b656de486f635
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10683
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch calculates the address where the chipset firmware descriptor
should be located and compares it against the actual value from Kconfig.
If the two don't match, it puts up a warning.
This could probably replace the config variable completely, but I wanted
to see how other people felt before doing that. I seem to recall that
the value used to be calculated, so I figure that there must be a reason
it's done this way at this point.
If we do want to keep the Kconfig setting, this patch could also be
modified to just verify that the HUDSON_FWM_POSITION is inside the ROM
space.
Change-Id: I94addf463e2c694a94eef218ec855103a3bb5da5
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10682
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update the ifdfake region questions in Kconfig with help descriptions
and prompts to allow values to be entered and not just use pre-defined
default values.
Change-Id: Ifdffadc3d74ec49492c2ded66623a1be6945425f
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10649
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the Kconfig question to allow the user to lock the ME section
using ifdtool.
Change-Id: I46018c3bc9df3e309aa3083d693cbebf00e18062
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10648
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Add the common/firmware subdir to the baytrail & fsp_baytrail
makefiles and remove the code it replaces.
- Update baytrail & fsp_baytrail Kconfigs to use the common code.
- Update the IFD Kconfig help and prompts for the TXE vs ME.
- Whittle away at the CBFS_SIZE defaults. All the fsp_baytrail
platforms have their own defaults.
Change-Id: I96a9d4acd6578225698dba28d132d203b8fb71a0
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10647
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When I added the common IFD Kconfig and Makefile, My thinking was that
I could use this symbol to differentiate between the ME and the TXE,
and to exclude the ME questions from platforms that use the IFD, but
don't use an ME, like Rangeley. In practice this made things a lot
more complicated and isn't worth it.
Change-Id: I4428744e53c6bb7fc00a4fa4f0aa782c25fc9013
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10678
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Besides the first five DWORDs, the offsets 0x40 & 0x41
are used to save SPI settings. They should only be 0xFF
for being written.
Other parts in ROMSIG are also changed to 0xFF for potential
requirement.
Change-Id: I61ea8295d5ee8ffbbd0cfcf9e4bece770d70e1f2
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/10651
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The default route does work for all Chromebooks and is replaced
with platform-specific one in follow-up.
Change-Id: Ia1839ed38dacf44a89dc757394d054e17666f193
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10442
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We've got a lot of duplicated code to set up the IFD/ME/TXE/GBE/ETC.
This is the start of creating a common interface for all of them.
This also allows us to reduce the chipset dependencies for CBFS_SIZE.
Change-Id: Iff08f74305d5ce545b5863915359eeb91eab0208
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10613
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
AMD Kern uses PspSecureOs_prod_CZ.csbin rather than PspSecureOs_prod_CZ.sbin.
PspSecureOs_prod_CZ.csbin is the firmware in CarrizoPI v1.0.0.7.
Change-Id: Idf54ee808dd6965aec9b979be00b7f890a88b06d
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10639
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The symbols used in these expressions were not correct and would never
evaluate as true.
Change-Id: Ia20177f41505473b14bc7b8e4b6fb16de36cc295
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10437
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Kern is the southbridge of AMD Merlin Falcon(Carrizo).
This add support of HD audio, lpc, sata and usb for Kern.
Change-Id: Ie47e38bc1099cdb72002619cb1da269f3739678b
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10418
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
sata.asl and superio.asl are empty files. Remove them.
Change-Id: Icd3e990aa713281e46dcbd8e0847166c77656b1c
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10505
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
CPU-side logic is unchanged for this range of CPUs as long as all of them
use TSEG (or ASEG, just needs to be consistent). So uplift 206ax code while
extracting southbridge and APIC code into separate functions.
Change-Id: Ib365681d1da8115922c557fddcc59afc156826da
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10465
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Resync together, backporting a fix for the initialization of
8254 and 8259, as in commit 8d9a1bd5. Also fix a typo and
reduce out useless whitespace differences.
Change-Id: I9a9b1fb9083c5417a8d061f90a89074f2a601ddf
Signed-off-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reported-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/10453
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I1ba4bfa0ac36a09a82b108249158c80c50f9f5fd
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9599
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I7fca8c3fa15c1be672e50e4422d7ac8e4aaa1e36
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9598
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I3fc8e0339fa46fe92cc39f7afa896ffd38c26c8d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9597
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds a few bit counting functions that are commonly needed
for certain register calculations. We previously had a log2()
implementation already, but it was awkwardly split between some C code
that's only available in ramstage and an optimized x86-specific
implementation in pre-RAM that prevented other archs from pulling it
into earlier stages.
Using __builtin_clz() as the baseline allows GCC to inline optimized
assembly for most archs (including CLZ on ARM/ARM64 and BSR on x86), and
to perform constant-folding if possible. What was previously named log2f
on pre-RAM x86 is now ffs, since that's the standard name for that
operation and I honestly don't have the slightest idea how it could've
ever ended up being called log2f (which in POSIX is 'binary(2) LOGarithm
with Float result, whereas the Find First Set operation has no direct
correlation to logarithms that I know of). Make ffs result 0-based
instead of the POSIX standard's 1-based since that is consistent with
clz, log2 and the former log2f, and generally closer to what you want
for most applications (a value that can directly be used as a shift to
reach the found bit). Call it __ffs() instead of ffs() to avoid problems
when importing code, since that's what Linux uses for the 0-based
operation.
CQ-DEPEND=CL:273023
BRANCH=None
BUG=None
TEST=Built on Big, Falco, Jerry, Oak and Urara. Compared old and new
log2() and __ffs() results on Falco for a bunch of test values.
Change-Id: I599209b342059e17b3130621edb6b6bbeae26876
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3701a16ae944ecff9c54fa9a50d28015690fcb2f
Original-Change-Id: I60f7cf893792508188fa04d088401a8bca4b4af6
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/273008
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10394
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The input/output value max is no longer used for tracking the
bus enumeration sequence, everything is handled in the context
of devicetree bus objects.
Change-Id: I545088bd8eaf205b1436d8c52d3bc7faf4cfb0f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8541
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of scan_static_bus() and tree traversals is somewhat convoluted.
Start cleaning this up by assigning each path type with separate
static scan_bus() function.
For ME, SMBus and LPC paths a bus cannot expose bridges, as those would
add to the number of encountered PCI buses.
Change-Id: I8bb11450516faad4fa33b8f69bce5b9978ec75e5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8534
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
This change makes sure that LPC controller declares resources that it
actually decodes. bd82x6x already does it but i82801gx doesn't leading
to allocator potentially allocating something else to the same range.
Change-Id: Ieca9852e54c08e31d4d41aea97f317d9a6919806
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7662
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
This gets rid of ugly tseg_relocate for fsp_bd82x6x.
This is adaptation of a3e41c0896
Change-Id: I4e80e6e98d3a6da3e3e480e9368fae1b3ed67cd6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10353
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This gets rid of ugly tseg_relocate for ibexpeak.
This is backport of 29ffa54969 to ibexpeak.
Change-Id: I456d85abdbadb2fdccf77ca771e2518cf8b8c536
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10352
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This gets rid of ugly tseg_relocate for bd82x6x.
This is backport of 29ffa54969 to bd82x6x.
Change-Id: I0f52540851ce8a7edaac257a2aa83d543bb5e530
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10351
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Old igd.asl had inconsistent addresses (between _DOD and actual device)
and ghost devices. Any of those is enough to make brightness on windows
fail and make igd.asl out-of-ACPI-spec. Also old code favoured ridiculous
copying of the same thing 6 times per chipset. Leave only hooking up and
chipset-specific part in chipset directory. Move NVS handling and ACPI-spec
parts to a common file.
Change-Id: I556769e5e28b83e7465e3db689e26c8c0ab44757
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7472
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Follow up for commit b890a12, some contributions brought
back a number of FSF addresses, so get rid of them again.
Change-Id: I0ac0c957738ce512deb0ed82b2219ef90d96d46b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10322
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
