Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801xx code for the following parts:
- AC97 audio/modem
- Onboard network interface cards (NICs)
- USB 1.1 controllers
- SMBus controllers
Some other parts are still missing and will be added later.
Use PCI ID #defines from pci_ids.h everywhere. Constify various structs.
Also, fix some random cosmetic issues in the code.
All of this is relatively trivial and tested by manually building
all boards which currently use the i82801xx code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Remove dead code
* Remove unused variables
* Fix bug where array was one element too small
* Fix error value truncation, the old code never entered the error path
* Remove warnings
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No functional code changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2912 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code. This is trivial, I did it for the other components before.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge now:
From: Morgan Tsai <my_tsai@sis.com>
It supports SiS761GX / SiS966 chipset, only for AMD K8 platform so far.
Due to integrated VGA sharing system memory, some code in southbridge
folder have to init northbridge.
Copyright (C) 2007 Morgan Tsai <my_tsai@sis.com>
Copyright (C) 2007 Silicon Integrated Systems Corp. (SiS)
Change Log:
Newly support GIGABYTE GA-2761GXDK
CPU type: AMD AM2 socket
Northbridge: SiS 761GX
Southbridge: SiS 966
SuperIO: ITE8716F
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is tested with abuild so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For example: in C51/MCP55 or C51/MCP51
Will allow
1. C51 at 0x10 to 0x14, and MCP at 0 to 4
2. C51 at 1 to 4, and MCP at 7 to 0x0a
The reason is c51/mcp51/mcp55 reported unitid is 0x0f (far beyond it
needed), and will prevent us from putting them on bus 0.
Typical values for c51/mcp55 or c51/mcp51:
HT_CHAIN_UNITID_BASE = 0x10 # for C51
HT_CHAIN_END_UNITID_BASE = 0 # for mcp
If only have mcp with c51,
HT_CHAIN_UNITID_BASE = 0 # for MCP
#HT_CHAIN_END_UNITID_BASE = 0 # default value 0x20
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
accessible (but not writable), so that reading/loading a payload
from that area can work (for instance).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2700 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the new src/southbridge/amd/cs5536 code completely replaces it.
The Artecgroup dbe61 board currently uses it, but that is broken anyway
at the moment. A fix to use the new CS5536 code for it is being worked on.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
setup as the host on USB port4. In client mode the headers remain
available. Also fixes an outb to 0x80 to use the post_code() function.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
-This line, and those below, will be ignored--
M cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2637 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD GX and LX processors. This aguments the previous code, which was
very specific to the OLPC platform with general purpose support and
better integration with the VSA and CPUs.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as that is not RAM but used for other stuff.
First try at PCI init added to src/mainboard/tyan/s1846/Config.lb.
Use a real payload (FILO) per default now.
Note: this cannot boot a payload, yet, but it gets a lot further now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2623 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2557 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that's the same as broadcom/bcm5785.
Signed-off-by: bxshi <bingxunshi@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2548 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2200 (too many names, sounds like a criminal).
1) Linuxbios loads kernel A; kernel A loads kernel B. Everything works
fine.
2) Then I push the reset button.
3) Linuxbios loads kernel A; kernel A loads kernel B. Kernel B complains
about wrong checksum of the mptable and crushes later.
An investigation showed that in 3), short after kernel A (v2.6.19.2)
sets
the Bus Master Enable bit of the nVidia's USB1 controller
(pci_set_master()),
the mptable gets two bytes at physical address 0x80 damaged.
Nothing is plugged to the USB ports. Other two Sun workstations had the
same
behavior. This does not make sense to me unless the controller has a HW
bug.
I believe, this should better be fixed in the kernel USB driver.
For now this patch offers a possibility for linuxbios to reset the USB
controller by setting HostControllerReset bit in HcCommandStatus
Register.
It is enablead by using 'register "usb1_hc_reset"="1"' in 'chip
southbridge/nvidia/ck804' section of the mainboard's Config.lb.
Signed-off-by: Roman Kononov <kononov195-lbl@yahoo.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2546 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
won't compile), and breaks an unnecessary dependency on the usbdebug
code.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2543 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2540 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
heavily on the code for i82801dbm and i82801er
Signed-off-by: Jon Dufresne <jon.dufresne@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge_intel_i82801dbm_control should be named
southbridge_intel_i82801dbm_ops. Otherwise a compile error occurs if this
device is included in Config.lb of the mainboard.
Closes#62
Signed-off-by: Jon Dufresne <jon.dufresne@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2526 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
space offset 0x1000, and later is the acpi registers also mapped at 0x1000.
This patch fixes this behavior. Closes#44
Signed-off-by: <chn@virtutech.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2523 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same format for all CHIP_NAME() entries in LinuxBIOS (Closes#20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
long time and I could not get into the tracker.
These are patches to enable ms9185 support. Abuild passes.
Signed-off-by: bxshi <bxshi@msik.com.cn>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2486 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cs5536, but I don't want to mess up the OLPC, and we really need the lx
support NOW.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
signed-off-by: Jordan Crouse
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This one actualy works. You cannot just go mucking about with stuff that the VSA
has under its thumb. Bad Things happen. This does it the VSA way.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
here's a patch which replaces all DOS newlines with Unix newlines, and
removes some useless $Rev$, $Id$, and $Header$ tags.
(part 1)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2385 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
read code. SBbus reads to RAM now work. Yah!
- Rename the register constants to something I can look at
more easily.
- Make the logic flow match the flow from V1 assembly
- #if 0 out other SMbus functions that are still broken.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
UART. If the upper banks are enabled, then the Linux 8250 driver knows
how to set baud speeds greater then 115200. This was prompted by David
Woodhouse.
Jordan"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add support for NSC pc87351 SuperIO
add Bitworks/IMS manboard config
This is a very basic framework for the i440bx chipset and the
Bitworks IMS board that uses it. Most things are
structure only.
Known issues:
- SMbus reads to the RAM SPD come back
all zero.
- dump_spd_registers() is commented out since it breaks with
the default setting of generic_dump_spd.c where it wants
2 memory controllers.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the result should be ok though..
the purpose is dropping the old i82801er southbridge code
and using the ich5r code instead because its the same chip
but the code looks more solid and is used by many more systems.
Some of the old i82801er features have been ported (like hpet enable)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2241 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disable agp slot in config.lb
fix error in setting up com1 == should be TTYS0_BAUD
note that the uart8250 struct is a bad design, but so is the
uart8250 code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to fail later than before.
dos2unix'ed the xe7501devkit files, that might have caused some problems
before.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Special version for HDAMA rev G with 33Mhz test and reboot out.
- Support for CPU rev E, dual core, memory hoisting,
- corrected an SST flashing problem. Kernel bug work around (NUMA)
- added a Kernel bug work around for assigning CPU's to memory.
r2@gog: svnadmin | 2005-08-03 08:47:54 -0600
Create local LNXI branch
r1110@gog: jschildt | 2005-08-09 10:35:51 -0600
- Merge from Tom Zimmerman's additions to the hdama code for dual core
and 33Mhz fix.
r1111@gog: jschildt | 2005-08-09 11:07:11 -0600
Stable Release tag for HDAMA-1.1.8.10 and HDAMA-1.1.8.10LANL
r1112@gog: jschildt | 2005-08-09 15:09:32 -0600
- temporarily removing hdama tag to update to public repository. Will
reset tag after update.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
More Via EPIA
more via epia stuff, including the trival but fatal bug in auto.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1978 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
cache_as_ram for AMD and some intel
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
x96emu update from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
TLA is really diffcult to use. How am I going to
roll back my last commit ?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1953 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
Correction to the reduce emulator from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
set CK804 nic mac addr in MMIO instead of pci config
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
nvidia onboard lan support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smbus_read_byte routine updated as per suggestion by rgm
addition reset & wait_until_ready to allow correct reading of first
byte on epia systems.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Set adl855pc ROM_SIZE to 1M
Other minor debug prints until we get this fixed.
We're almost as far along as we were before the Change :-)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
crt0.S.lb: Modified so that it is safe to include console.inc
console.c: Added print_debug_ and frieds which are non inline variants of the normal console functions
div64.h: Only include limits.h if ULONG_MAX is not defined and define ULONG_MAX on ppc
socket_754/Config.lb Conditionally set config chip.h
socket_940.c We don't need and #if CONFIG_CHIP_NAME we won't be linked in if there are no references.
slot_2/chip.h: The operations struct need to be spelled cpu_intelt_slot_2_ops
slot_2/slot2.c: The same spelling fix
socket_mPGA603/chip.h: again
socket_mPGA603/socket_mPGA603_400Mhz.c: and again
socket_mPGA604_533Mhz/Config.lb: Conditionally defing CONFIG_CHIP_NAME
socket_mPGA604_800Mhz/chip.h: Another spelling fix
socket_mPGA604_800Mhz.c and again
via/model_centaur/model_centaur_init.c: It's not an intel CPU so don't worry about Intel microcode uptdates
earlymtrr.c: Remove work around for older versions of romcc
pci_ids.h: More ids.
malloc.c: We don't need string.h any longer
uart8250.c: Be consistent when delcaring functions static inline
arima/hdama/mptable.c: Cleanup to be a little more consistent
amdk8/coherent_ht.c:
- Talk about nodes not cpus (In preparation for dual cores)
- Remove clear_temp_row (as it is no longer needed)
- Demoted the failure messages to spew.
- Modified to gracefully handle failure (It should work now if cpus are removed)
- Handle the non-SMP case in verify_mp_capabilities
- Add clear_dead_routes which replaces clear_temp_row and does more
- Reorganize setup_coherent_ht_domain to cleanly handle failure.
- incoherent_ht.c: Clean up the indenation a little.
i8259.c: remove blank lines at the start of the file.
keyboard.c: Make pc_keyboard_init static
ramtest.c: Add a print out limiter, and cleanup the printout a little.
amd8111/Config.lb: Mention amd8111_smbus.c
amd8111_usb.c: Call the structure usb_ops not smbus_ops.
NSC/pc97307/chip.h: Fix spelling issue
pc97307/superio.c: Use &ops no &pnp_ops.
w83627hf/suerio.c: ditto
w83627thf/suerio.c: ditto
buildrom.c: Use braces around the body of a for loop. It's more maintainable.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ram linuxbios_ram instead of linuxbios_c and linuxbios_payload...
- Reordered the linker sections so the LinuxBIOS fallback image can take more the 64KiB on x86
- ROM_IMAGE_SIZE now will work when it is specified as larger than 64KiB.
- Tweaked the reset16.inc and reset16.lds to move the sanity check to see if everything will work.
- Start using romcc's built in preprocessor (This will simplify header compiler checks)
- Add helper functions for examining all of the resources
- Remove debug strings from chip.h
- Add llshell to src/arch/i386/llshell (Sometime later I can try it...)
- Add the ability to catch exceptions on x86
- Add gdb_stub support to x86
- Removed old cpu options
- Added an option so we can detect movnti support
- Remove some duplicate definitions from pci_ids.h
- Remove the 64bit resource code in amdk8/northbridge.c in preparation for making it generic
- Minor romcc bug fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- mem.h and sizeram.h and all includes killed because the are no longer needed.
- linuxbios_table.c updated to directly look at the device tree for occupied memory areas.
- first very incomplete stab a converting the ppc code to work with the dynamic device tree
- Ignore resources before we have read them from devices, (if the device is disabled ignore it's resources).
- First stab at Pentium-M support
- add part/init_timer.h making init_timer conditional until there is a better way of handling it.
- Converted all of the x86 sizeram to northbridge set_resources functions.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is way to much code duplication but for now things work.
- Fix the typo in amd8111_lpc.c
- Remove an unused macro, use continue instead of break in mtrr.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1704 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Enable resources on the lpc bus. PCI now longer do this by
default for their children unless they are bridges.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf Marek