The UARTs in the Picasso SoC are memory mapped, but there is also some
hardware support that isn't used by any board to make the UARTs behave
like the ones found on legacy x86 machines from the 90s.
In the MMIO mode the MMIO address of the UART controller is passed to
the OS via ACPI. The OS expects the base clock of the UART controller to
be 48MHz (see the cz_uart_desc struct in drivers/acpi/acpi_apd.c and
drivers/tty/serial/8250/8250_dw.c in the Linux kernel) in this case. It
is also possible to enable additional decodes from four 8 byte legacy
I/O locations used for serial ports to the different UART controllers,
which doesn't disable the MMIO access though. The legacy I/O-mapped
serial ports are usually expected to have a base clock of 16*115200Hz
which the hardware can also provide to the UART's baud rate generator.
So there are two possible valid configurations to use the UARTs; either
MMIO access in combination with a 48MHz base clock or the legacy I/O
decode with a ~1.8MHz base clock.
The existing code unconditionally generates ACPI objects for all enabled
UARTs, so those shouldn't be put into legacy mode and switching the base
clock to ~1.8MHz was only done in the case that the UART was used as
coreboot console UART which still used the MMIO access, but the lower
base clock. Since no board even selects this option and it's rather
invasive to properly implement this feature, just drop the corresponding
broken code.
TEST=SoC UART console still works on Mandolin.
Change-Id: I26fa8fdfc781b583ba56ac4dbcbbfb6100e84852
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49371
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is causing boot errors on zork:
coreboot-v1.9308_26_0.0.22-18590-g4598a7bed945 Wed Dec 16 17:32:25 UTC 2020 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area FW_MAIN_B found @ 312000 (3137280 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1f2bbdd9c87c4efdfb0042e90a20b489fa0efced
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change lets IOM consider all USB connected devices as device
attached(DA) scenario. While connecting a typec-to-a dongle, IOM would
disable TC cold and help to resolve enemuration failure after usb3
device is plugged into the dongle.
BUG=b:173054070
TEST=Build and boot on delbin.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0ad0322693b4f8fbf1000b24eb21dddcebec686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The name `..._index` is confusing since the maximum index of an array is
not `ARRAY_SIZE(array)` but `ARRAY_SIZE(array) - 1`.
Rename `uart_max_index` to `uart_ctrlr_config_size` to make the name
match the variable´s value.
Change-Id: I7409c9dc040c3c6ad718abc96f268c187d50d79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It is only used in one place, and there's two other equivalent macros.
Change-Id: I7c8241e28f688abd2df8180559dd02ee441c7023
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This change adds a helper function `pcie_rp_enable_mask()` that
returns a 32-bit mask indicating the status (enabled/disabled) of PCIe
root ports (in the groups table) as configured by the mainboard in the
device tree.
With this helper function, SoC chip config does not need to add
another `PcieRpEnable[]` config to identify what root ports are
enabled.
Change-Id: I7ce5fca1c662064fd21f0961dac13cda1fa2ca44
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48968
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
Change-Id: Icccd9d15a9e9a22c9bfe7a9843e95d77013c9c8f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49047
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi
- Linux tested on clevo/cml-u
Change-Id: I51fdf52419aa7f059b70a906fd8bdac88d5b6046
Tested-By: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49046
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for the Intel LPIT table to support reading Low Power Idle
Residency counters by the OS. On platforms supporting S0ix sleep states
there can be two types of residencies:
* CPU package PC10 residency counter (read from MSR via FFH interface)
* PCH SLP_S0 assertion residency counter (read via memory mapped
interface)
With presence of one or both of these counters in the LPIT table, Linux
dynamically adds the corresponding attributes to the cpuidle sysfs
interface, that can be used to read the residency timers:
* /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
* /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
The code in src/acpi implements generic LPIT support. Each SoC or
platform has to implement `acpi_fill_lpit` to fill the table with
platform-specific LPI state entries. This is done in this change for
soc/intel/common, while being added as its own compilation unit, so SoCs
not yet using common acpi code (like Skylake) can use it, too.
Reference:
https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi together with CB:49046
- Linux tested on clevo/cml-u, supermicro/x11ssmf together with CB:49046
Change-Id: I816888e8788e2f04c89f20d6ea1654d2f35cf18e
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a minimal chipset tree with only two devices:
1. Domain
2. GNB root complex
This allows sconfig to generate the config structure for SoC root
device that is used by config_of_soc().
Change-Id: I7e08ecf4b9556dc9325bd5a6a51566a949ceb73f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
This change updates various uart_* functions to use simple(_s_)
variants of PCI functions. This is done for a few reasons:
* __SIMPLE_DEVICE__ check can be dropped since the same data type can
be used in early stages and ramstage.
* Removes the requirement on early stage to walk the device tree to
get access to the device structure. This allows linker-based device
tree optimizations for early stages.
As part of this change, uart_get_device() is refactored and a new
function uart_console_get_devfn() is added which returns pci_devfn_t
in MMCONF format. It is then used directly by the _s_ variants of PCI
functions.
Change-Id: I344037828118572ae5eb27c82c496d5e7a508a53
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change renames `struct uart_gpio_pad_config` to `struct
uart_controller_config` and adds a new parameter devfn (which expects
devfn for the UART controller corresponding to the index in
PCI_DEVFN() format). This gets rid of the SoC callback to get `struct
device` pointer to the UART controller device.
Change-Id: Id0712a0038f2cc1a61b8b5a58fa155f14e7949a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49212
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
Tested by checking lspci output on System76 galp3-c (WHL), oryp5 (CFL),
and oryp6 (CML).
References:
- TigerLake FSP Integration Guide
- Intel Document Number 337868-002
Change-Id: Ieaa45ef7fa8e0da4a25b9174ded1ea0c5d9c4b4e
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49104
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Separate GPIO define into gpio_defs.h, then we can use it in asl include.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If2a779eae228f621e77610889205853de2fb179a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The xHCI controller supports waking the system from S1-S4.
Thus specify that the deepest sleep state is S4 in _PRW.
Tested on Prodrive/hermes. The board now wakes from S4 as well by
pressing a key on the USB keyboard.
Change-Id: I0bb266e70ee6b4eb8922671b7d0078db0d29a1da
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49224
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Create new Kconfig MAX_CPU_ROOT_PORTS and MAX_PCH_ROOT_PORTS as per
EDS.
2. Add new chip variable to enable/disable CPU PCIE RPs from mainboards.
3. Rename PcieRpEnable to PchPcieRpEnable.
4. Enable CPU RPs as below in mainboard devicetree.cb
RP1: PEG60 : 0:6:0 : CPU SSD1
RP2: PEG10 : 0:1:0 : x8 CPU Slot
RP3: PEG62 : 0:6:2 : CPU SSD2
Change-Id: I92123450bd7cfb2e70aae8de03053672a7772451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49136
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is needed to allow switching to Haswell CPU code in the future.
Change-Id: Ic642f32f9c4a269a66ac470b7a7217f20ff8bfba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46886
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Name the common part of GNVS initialisation as soc_fill_gnvs().
It is also moved before the call to acpi_create_gnvs(), which
followup will rename to mainbord_fill_gnvs() to reflect that
implementation is under mb/.
Change-Id: Ic4cf1548b65a86212d6e45d460fcd23bb8036365
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48706
Reviewed-by: Lance Zhao
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Already done in common gnvs_get_or_create() implementation
once gnvs_chromeos_ptr() is defined for platforms.
Change-Id: I90fa2bc28ae76da734b3f88be057435aed9fe374
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48703
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allocation now happens prior to device enumeration. The
step cbmem_add() is a no-op here, if reached for some
boards. The memset() here is also redundant and becomes
harmful with followup works, as it would wipe out the
CBMEM console and ChromeOS related fields without them
being set again.
Change-Id: I9b2625af15cae90b9c1eb601e606d0430336609f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48701
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
uart_common_init is not used outside of
soc/intel/common/block/uart.c. This change restricts the scope to this
file and drops the declaration from uart.h
Change-Id: I499a53506f9b2e91ecc7334bf9b023d342e802fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49211
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the parameter passed into `lpss_set_power_state()`
from struct device * to pci_devfn_t. This allows the users in the
early stages to use pci_devfn_t instead of having to walk the device
tree to get a pointer to the relevant device structure. It is
important for optimizing out unnecessary components of the device tree
from the early stages.
Change-Id: Ic9e32794da65348fe2a0a2791db47ab83b64cb0f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49210
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change drops the parameter `struct device *dev` from the function
`soc_get_gen_io_dec_range()`. This function uses the parameter dev to
get a pointer to config structure for extracting the decode ranges
configured by mainboard in device tree. However, there is no separate
chip driver for the LPC device which means that the SoC code can use
`config_of_soc()` to get to SoC chip config instead of using the LPC
device.
This change is being done in preparation to clean up the device
tree/chip config access in early stages that allows for optimizing
the inclusion of device tree elements in the early stages.
Change-Id: I3ea53ddc771f592dd0ea5e5e809be2d2eff7f16d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
USB3 is in CPU and USB2 in PCH on Tigerlake. Cross die messaging is
implemented between CPU and PCH through the IOSF SB bridge. a PCH xHCI
USB2 port reset event issued by the xHCI driver shall trigger a message
upstream to CPU to wake it from the low power state which allows a USB3
device that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Built and booted to kernel on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I672f30a117980bc10bd71e9b77c5fa76286b9f5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49052
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Trying to do multiple operations on the same CBFS image at the same time
likely leads to data corruption. For this reason, add BSD advisory file
locking (flock()) to cbfstool (and ifittool which is using the same file
I/O library), so that only one process will operate on the same file at
the same time and the others will wait in line. This should help resolve
parallel build issues with the INTERMEDIATE target on certain platforms.
Unfortunately, some platforms use the INTERMEDIATE target to do a direct
dd into the CBFS image. This should generally be discouraged and future
platforms should aim to clearly deliminate regions that need to be
written directly by platform scripts with custom FMAP sections, so that
they can be written with `cbfstool write`. For the time being, update
the legacy platforms that do this with explicit calls to the `flock`
utility.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I022468f6957415ae68a7a7e70428ae6f82d23b06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We need to fill Acoustic noise mitigation related UPDs only in
case when acoustic noise mitigation is enabled. This will also
clarify the user that they need to enable Acoustic noise
mitigation while using this config in mainboard.
We're only filling UPD for domain VR index 0 since there is only
one VR domain for JSL (VCCIN VR).
Reference: JSL EDS (Document# 613601) (Chapter 3.4)
BUG=None
BRANCH=dedede
TEST=UPD values are getting filled correctly when Acoustic noise
mitigation is enabled.
Change-Id: I0cf4ccfced13b0d32b3d20713eace63e66945332
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
USBSUSPGQDIS is a disqualifier bit which will allow platform
to enter s0ix even if USB2 PHY SUS is not power gated. Disabling this
bit will ensure that USB2 PHY SUS is power gated before entering s0ix.
BUG=b:175767084
BRANCH=dedede
TEST=s0ix works on drawcia and USB wake from s0ix works fine.
Change-Id: I20bad3f79141799c88a16272ea822b9e3dede504
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
This was used as a guard to not raise SMI with
APM_CNT_GNVS_UPDATE. The handler has been removed
now completely.
Change-Id: I7726367fd16630aa4b4b25b24b05f740645066db
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add GRXS and GTXS into gpiolib. We can align with Intel ACPI method
for the better usage. This benefits acpi.c to be more clear, too.
BUG=b:176270381
BRANCH=zork
TEST=Confirm the Goodix touchscreen functional.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1aa6a8f44f20577e679336889c849dd67cb99f2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add STXS and CTXS into gpiolib. We can align with Intel ACPI method
for the better usage. This benefits acpi.c to be more clear, too.
BUG=b:176270381
BRANCH=zork
TEST=Confirm the Goodix touchscreen functional.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If4fcd68496a712fdccf44b91a6192ef58a0a9733
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48943
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For arch/x86 the realmode part has to be located within the same 64
KiB as the reset vector. Some older intel platforms also require 4 KiB
alignment for _start16bit.
To enforce the above, and to separate required parts of .text without
matching *(.text.*) rules in linker scripts, tag the pre-C environment
assembly code with section .init directive.
Description of .init section for ELF:
This section holds executable instructions that contribute to the
process initialization code. When a program starts to run, the
system arranges to execute the code in this section before calling the
main program entry point (called main for C programs).
Change-Id: If32518b1c19d08935727330314904b52a246af3c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47599
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mainboard user can select VGA_ROM_RUN_DEFAULT Kconfig hence
no need to have another ENABLE_DISPLAY_OVER_EXT_PCIE_GFX Kconfig to
load/execute VGA OpRom.
Change-Id: Id87f82d9c3657afad9db94b1ec0917121edfe2bb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49023
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CSE lite SKU has 2 CSE firmware boot partitions vs 3 for the "normal"
SKU; this has nothing to do with building for ChromeOS or not, and by
having this dependency, boards with select the CSE lite SKU are unable to
build with CONFIG_CHROMEOS unset due to Kconfig dependency issues.
Test: build google/wyvern with CONFIG_CHROMEOS not set.
Change-Id: I6959f35e1285b2fab7ea1f83a5ccfcb065c12397
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
All Broadwell boards use 8 for MAX_CPUS, so this option can be factored
out into SoC Kconfig.
Change-Id: I311b95ea75a7c6b76b32c7197a0cec86db644234
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCI interrupt line registers are used as a last resort if routing
can't be fetched from either ACPI or the MPTable. This change correctly
sets the registers. It overrides the pirq_data set by the mainboards
since the routing is fixed in AGESA.
BUG=b:170595019
TEST=Boot ezkinil with `pci=nomsi,noacpi amd_iommu=off noapic`
Verified all PCI peripherals are still functional.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If5d4d8f613c8d0fa9b43cefa804824681c3410d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The original routing table did not handle all 8 INTx interrupts.
Additionally it also didn't take the swizzling into account.
Now that we know how AGESA programs the routing table we can correctly
generate it.
We still route the PCI interrupts through the FCH IOAPIC. A follow up
will have the GNB IOAPIC handle the PCI interrupts.
There is still work to be done to fix the legacy PCI_IRQ register for
each PCI device. We can then remove the mainboard_pirq_data from each
mainboard.
BUG=b:170595019
TEST=Used ezkinil
Boot kernel with `pci=nomsi amd_iommu=off noapic` and
`pci=nomsi amd_iommu=off` then verified system
was usable and verified /proc/interrupts looked correct.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2b2cce9913081d5cd456043ba619a79c1dfd4a8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The set_resources field in the root_complex_operations struct shouldn't
be NULL, but a pointer to noop_set_resources instead. This fixes the
error "PCI: 00:00.0 missing set_resources".
Change-Id: I2d9f3850b3051c92cd9c0f52f8570f4fd6133070
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When configuring a GPIO pin as output the value should be written before
it gets configures as an output to avoid a possible glitch on the output
when the GPIO pin was an input before and the output value was different
from the one that got written afterwards.
Change-Id: I2bb5e629ef0ed2daadc903ecc1852200fe3a5cb9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The functions to configure a GPIO as input with pull-up/down need to
clear the output enable bit, so that the direction will be input. If the
pin was configured as output before, the pin direction was still output
after this call which is at least unexpected.
Change-Id: Id1fa1669195080b34fd62324616825415728b0b4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If the pin was configured as pull-up/down before this wouldn't get
cleared when calling gpio_input before.
Change-Id: I17d5eccb7492138e64abaecbd7cb853adb8c4d2d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch updates CPU microcode patch base address/size to FSP-S
UPD to have second microcode patch loaded successfully to enable
Mcheck flow.
This is new feature requirement for ADL as per new Mcheck initialization
flow.
BUG=b:176551651
TEST=Able to reach beyond PC6 without any MCE.
Change-Id: I936816e3173dbcdf82b2b16b465f6b4ed5d90335
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48847
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LPEA device memory resources, required by Windows drivers,
were not being set. Allocate required resources using
soc/intel/braswell/acpi/southcluster.asl as a reference.
This patch alone is not sufficient for working audio under Windows
on Baytrail ChromeOS devices, but it is a necessary component.
Test: boot Windows 10 on google/swanky, observe LPEA device working properly.
Change-Id: I7994d9b2c6e134c01b05cd7c61d309b6ba6e88e5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48745
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT.
Hook into soc/common framework by implementing intel_igd_get_controller_info().
Add Kconfig entries to set the correct register offsets for backlight
frequency and duty cycle.
Change-Id: Ia62a88b58e7efd90f550000fc5b2cef0cb5fade7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move CPUID definitions out of msr.h into new cpuid.h header.
BUG=b:155307433
BRANCH=Zork
Change-Id: I2ed5e0a5a6dbdb38fce8bf3e769f680330718653
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
There are multiple different devicetree setting formats for graphics
panel settings present in coreboot. Replace the ones for the platforms
that already have (mostly) unified gma/graphics setup code by a unified
struct in the gma driver. Hook it up in HSW, BDW, SKL, and APL and adapt
the devicetrees accordingly.
Always ensure that values don't overflow by applying appropriate masks.
The remaining platforms implementing panel settings (GM45, i945, ILK and
SNB) can be migrated later after unifying their gma/graphics setup code.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I445defe01d5fbf9a69cf05cf1b5bd6c7c2c1725e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
For easier review of the switch to a new register struct in the
follow-up change, the panel delay times get converted from destination
register raw format to milliseconds representation in this change.
Formula for conversion of power cycle delay:
gpu_panel_power_cycle_delay_ms =
(gpu_panel_power_cycle_delay - 1) * 100
Formula for all others:
gpu_panel_power_X_delay_ms = gpu_panel_power_X_delay / 10
The register names gain a suffix `_ms` and calculation of the
destination register raw values gets done in gma code now.
Change-Id: Idf8e076dac2b3048a63a0109263a6e7899f07230
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
SoC will transmit the EoTp (End of Transmission packet) when
MIPI_DSI_MODE_EOT_PACKET flag is set.
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: Ifadd0def13cc264e9d39ab9c981fbdc996396bfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The flash controller driver can be shared among mt8173 and mt819x.
TEST=boot to kernel on Asurada
boot to kernel on Hana (w/o BL31)
Change-Id: I4e5213563189336496122a0f2d8077b3e5245314
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
To get better PI linearity, perform 8 phase calibration to do
MCK 0/180/45 training and select the best PI settings.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ib4ccaa8d43b8382cbc64cf82de86ad1ac16cb89a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
which select INTEL_GMA_ACPI. Rework brightness level includes and
platform-level asl files to avoid duplicate device definition for GFX0.
Include gfx.asl for Skylake/Kabylake, since all other soc/intel/common
platforms already do. Adjust mb/51nb/x210 to prevent device redefinition.
Some OSes (e.g. Windows, MacOS) require/prefer the ACPI device for
the IGD to exist, even if ACPI brightness controls are not utilized.
This change adds a GFX0 ACPI device for all boards whose platforms
select INTEL_GMA_ACPI without requiring non-functional brightness
controls to be added at the board level.
Change-Id: Ie71bd5fc7acd926b7ce7da17fbc108670fd453e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
eint event mask register is used to mask eint wakeup source on mt8192.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
BUG=b:169024614
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I8ee80bf8302c146e09b74e9f6c6c49f501d7c1c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46409
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the right register values for backlight control to CNL's Kconfig.
To make iasl happy about the reversed register order, split the field.
Change-Id: I05a06cc42397c202df9c9a1ebc72fb10da3b10ec
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds the required gpio operations struct to soc/common gpio
code and hooks them up in all socs currently using the gpio block code,
except DNV-NS, which is handled in a separate change.
Also, add the gpio device to existing chipset devicetrees.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: I81dbbf5397b28ffa7537465c53332779245b39f6
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48583
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct the mask for the power cycle delay from 0xff to 0x1f, to
represent the actual maximum value according to Intel graphics PRM for
Haswell, Volume 2c and Intel graphics PRM for Broadwell, Volume 2c.
Change-Id: Ib187f1ca6474325475e5ae4cc1b2ffbce12f10bf
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48957
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow TGL chipset.cb to add alias for TCSS and USB ports.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I803dad0af09b26a55ffb767826ba79cf61de04ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48793
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Kaby Lake PCH can have up to 24 PCIe root ports. Thus, add 4 missing
root ports to the chipset devicetree.
Change-Id: I443fb736873d47f1b6fe7718a10e1bb4ae5df2a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48947
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add rtc MT6359P driver for rtc init and rtc eosc calibration. Refactor
mt8173 and mt8183 code by extracting common API. Move rtc_read and
rtc_write to each SoC folder, because mt8173 and mt8183 access rtc via
pmic wrapper, while mt8192 accesses it via pmif.
Reference datasheet:
Document No: RH-D-2018-0101.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: I57d6738fdec148c7458b2024a0a8225415ca2f3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add basic devapc (device access permission control) drivers.
DAPC driver is used to set up bus fabric security and data protection
among hardwares. DAPC driver groups the master hardwares into different
domains and gives secure and non-secure property. The slave hardware can
configure different access permissions for different domains via DAPC
driver.
Change-Id: I2ad47c86b88047c76854a6f8a67b251b6a9d4013
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
src/northbridge/amd/pi/00660F01/Kconfig does not exist. Remove the
source statement.
Also, no kconfig files under src/soc/intel/common/basecode/. Clean
that up.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I10917b76ff6c2a9d5a97d5c7dfa9e8925cd8c8a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Now that CHAP device is declared in chipset devicetree, hook it up to
devicetree configuration.
Change-Id: Icc51f7b9cda32d5058dce958e386921b6d3d8ffb
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48323
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Structure with chromeos_acpi_t is expected to have size
0x1000. Only ones with device_nvs_t have size 0x2000.
Change-Id: I2eaa3a008566853b4144fa34ccffaa232d5d8e24
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Rename to graphics_soc_panel_init, to more accurately convey
operations performed by the function. Guard execution so we
don't attempt to reconfigure the panel after FSP has already
done so.
This fixes FSP/GOP display init on APL/GLK, which was broken by
attempting to configure the panel after FSP had already done so.
Change-Id: I8e68a16b2efb59965077735578b1cc6ffd5a58f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48884
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This file was being written to the root src directory. It is the only
file being written to src during a normal build, while all others are
being written to $(obj). I added a new variable to allow specifying the
xcompile path. This allows generating a single file if building multiple
boards. I also moved the default location into $(obj) so we don't
pollute the src directory by default.
I also cleaned up the generation of xcompile by removing the unnecessary
eval and NOCOMPILE check.
I also left .xcompile in distclean so it cleans up stale files.
Since .xcompile is written into $(obj), `make clean` will now remove it.
The tegra Makefiles are outside of the normal build process, so I just
updated those Makefiles to point to the default xcompile location of a
normal build. The what-jenkins-does target had to be updated to support
these special targets. We generate an xcompile specifically for these
targets and pass it into the Makefile. Ideally we should get these
targets added to the main build.
BUG=b:112267918
TEST=ran `emerge-grunt coreboot` and `make what-jenkins-does`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia83f234447b977efa824751c9674154b77d606b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Commit 56fcfb5 misused the PCH_DEVFNs passed to the XHCI elog driver, by
passing them directly to pci_s_read_config32. This is incorrect, as it
is the wrong PCI devfn encoding to pass to that function.
BUG=b:175996770
TEST=abuild
Change-Id: Id7c146c1f50ee64a725bd50f9f11a7f159013a2b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Current implementation uses CPUID 0Bh function that returns the number
of logical cores of requested level. The problem with this approach is
that this value doesn't change when HyperThreading is disabled (it's in
the Intel docs), so it breaks generate_cpu_entries() because `numcpus`
ends up being zero due to integer division truncation.
- Use MSR 0x35 instead, which returns the correct number of logical
processors with and without HT.
- Use cpu_read_topology() to gather the required information
Tested on Prodrive Hermes, the ACPI code is now generated even with
HyperThreading disabled.
Change-Id: Id9b985a07cd3f99a823622f766c80ff240ac1188
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Following up 3ccae2b7, this patch adds Iccmax and AC/DC
loadlines and iPL2 for CML-S CPUs. The information is from
CML EDS volume 1, doc #606599 and pdg #610244.
Change-Id: Id2797a979a8b6a52a34baae66f95c7136ed1dc72
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38288
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to doc# IHD-OS-BXT-Vol 2b-05.17 the cycle delay is in the bit
range 8:4 of register PP_CONTROL. The current code writes the value to
bits 4:0, though. Correct that by shifting the value left by 4 bits.
Change-Id: If407932c847da39b19e307368c9e52ba1c93bccd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Files under sb/ or soc/ should not have includes that tie those
directly to external components like ChromeEC os ChromeOS
vendorcode.
Change-Id: Ib56eeedaa9d7422e221efa9c8480ed5e12024bca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48765
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
psp.h was first included when Stoney Ridge began loading the first
SMU firmware. That step was later moved from bootblock to romstage.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Id646390ce377143d09455f797de1b149dbb615b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48797
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Memory PLL is used to provide the basic clock for dram controller
and DDRPHY. PLL must be initialized as predefined way.
First, enable PLL POWER and ISO, wait at least 30us, release ISO, then
configure PLL frequency and enable PLL master switch.
At last, enable control ability for SPM to switch between active and
idle when system is switched between normal and low power mode.
TEST=Confirm Memory PLL frequency is right by frequency meter
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ieb4e6cbf19da53d653872b166d3191c7b010dca6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Use the common block ACPI to further reduce the duplicate code.
Change-Id: If28d75cbb2a88363d70e3ae6a2cace46cb6bbbab
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48248
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Don't depend on the MTRR setup left over from FSP-M ExitTempRam.
Change-Id: I299123b3cd3c37b4345102c20fda77bf261892a2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Add a hook for SOCs to provide an IOAPIC MADT table. If the
SOC doesn't provide a table then a standard setting is used.
Change-Id: Ic818a634e4912d88ef93971deb4da5ab708c9020
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change static calculate_power() function to global and update the name
to common_calculate_power_ratio() for SOC ACPI code use.
Change-Id: I0e2d118ad52b36859bfc6029b7dee946193841f4
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Move sb_clk_output_48Mhz out of acp. It should be called unconditionally.
We may have another device need this clock e.g. superio chip.
BUG=b:174121847
BRANCH=zork
TEST= build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I30ad6c60066f17cc83e7feb40675610f4853a022
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
If we have use external clock source for I2S, we don't need to enable
internal one. Add acp_i2s_use_external_48mhz_osc flag for the project
which uses external clock source.
BUG=b:174121847
BRANCH=zork
TEST= build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ica68ee2da5a05231eb6db0218bd0f19907507273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This still uses the common GPIO code that supports setting up SMI/SCI
support for the GPIOs in all stages, which will get removed in future
patches, so for now the SoC's gpio.c needs to be included in all stages.
Change-Id: I6c12d1d6c605b7eb063eef62a1f71860f602f8dd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48565
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `azalia_set_bits` will mask out all bits, so just use zero for
clarity. The resulting behavior is the same in both cases.
Change-Id: I27777f1e836fa973859629d48964060bec02c87a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
coreboot already unconditionally enables CLKRUN_EN in SoC common code.
Tested on an out-of-tree Acer Aspire VN7-572G, PCCTL[CLKRUN_EN]
of LPC is still enabled.
Change-Id: I65e85015bdd0f766ca8021a3d4c0b0d799f0ccc5
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48325
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This function is equivalent to `azalia_find_verb` in its current form,
so replace them. Also, adapt and move the function description comment.
Change-Id: I40d1e634c31b00bd7808a651990d9bd6f0d054e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
There's many copies of this function in the tree. Make the copy in
azalia_device.c non-static and rename it to `azalia_set_bits`, then
replace all other copies with it. Since azalia_device.c is only built
when AZALIA_PLUGIN_SUPPORT is selected, select it where necessary.
This has the side-effect of building hda_verb.c from the mainboard
directory. If this patch happens to break audio on a mainboard, it's
because its hda_verb.c was always wrong but wasn't being compiled.
Change-Id: Iff3520131ec7bc8554612969e3a2fe9cdbc9305e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use FSPS_UPD instead of FSP_S_CONFIG as argument as already done on
xeon_sp and denverton_ns. This allows to set test config UPDs from
mainboard code as well.
Change-Id: I6d67264e22df32b9210ce88b99d6a7a4f6b97ffb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Currently it's not possible to add multiple graphics driver into
one coreboot image. This patch series will fix this issue by providing
a single API that multiple graphics driver can use.
This is required for platforms that have two graphic cards, but
different graphic drivers, like Intel+Aspeed on server platforms or
Intel+Nvidia on consumer notebooks.
The goal is to remove duplicated fill_fb_framebuffer(), the advertisment
of multiple indepent framebuffers in coreboot tables, and better
runtime/build time graphic configuration options.
Replace set_vbe_mode_info_valid with fb_add_framebuffer_info or
fb_new_framebuffer_info_from_edid.
Change-Id: I95d1d62385a201c68c6c2527c023ad2292a235c5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
On SKX FSP-M does not return if this is set too early.
Tested on OCP/Tiogapass, boots.
Change-Id: Ib8ef7bab36bfd4b62988768753d10b4d7b7d567f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48657
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The local function names were chosen such that they don't
collide with <gpio.h> so the prefix is unnecessary.
Change-Id: I4799a6d6b87e8081324d88b0773e61cbda0d4cfb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We have identical gdtptr16 and gdtptr. The reference in
gdtptr_offset calculation is not accounted for when
considering --gc-sections, so to support linking
gdt_init.S separately add dummy use of gdtptr symbol.
Realmode execution already accessed gdt that was located
outside [_start16bit,_estart16bit] region. Remove latter
symbol as the former was not really a start of region,
but entry point symbol.
With the romcc bootblock solution, entry32.inc may have
been linked into romstage before, but the !ENV_BOOTBLOCK
case seems obsolete now.
Change-Id: I0a3f6aeb217ca4e38b936b8c9ec8b0b69732cbb9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The voltage of vm18 should be microvolt instead of millivolt.
BUG=b:155253454
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Iea5b46c1df358dc350506d29cc033d01631b37b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Keep the CONN MCU in reset state to prevent CONN from asserting the
clk26m request to SPM.
TEST=clk26m request from conn has been released.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: Ia1b706da497ba2827341051459c3628e2ae9240f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
UFS reference clock (refclk) is enabled by default, which will cause
the UFSHCI to hold the SPM signal and lead to suspend failure. Since
UFS kernel driver is not built-in, disable refclk in coreboot stage.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Change-Id: If11c1b756ad1a0b85f1005f56a6cb4648c687cf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
GEVENT_MASK should cover all GEVENT pins, but was missing
SMITYPE_G_AGPIO9 and SMITYPE_G_AGPIO8.
Change-Id: Ia676476e2d2cf468d82d6d90e9fc11d34f56f153
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Base address symbols for ACPIMMIO banks that would not get
assigned at runtime must not resolve at linker-stage either.
The build of PSP-verstage should pass without the preprocessor
macros that have x86-centric view of memory space.
Change-Id: I3cb1b5a90023ebc4359835be716c5e3f9451df60
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
