The EC LPC init function needs to run to enable the internal keyboard.
I needed this to confirm that it is just USB keyboards that are causing
all sorts of issues.
BUG=chrome-os-partner:23635
BRANCH=rambi
TEST=boot to recovery screen and hit tab
Change-Id: Iea0fc66ba62ea7da71ef83c26e25ae32bef102bd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175207
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4915
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Enable first SATA port in Rambi device tree.
BUG=chrome-os-partner:23643
TEST=TEST=Manual, in dev mode. Verify on rambi that SATA disk is
detected, and kernel is found + booted.
Change-Id: Ic0cb5f9ff17ca0f6cc7941f203b9338df200811d
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174916
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4914
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Add the on-board devices in the SoC to the device tree.
Also, disable the unused devices aside from TXE and HDA.
Those particular devices cause the system to shut down
when they are disabled.
BUG=chrome-os-partner:22871
BRANCH=None
TEST=Built and booted through depthcharge. Noted the calls to the
southcluster disable function.
Change-Id: I482c1c9609833054aeb2948144af54b57d3df086
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174645
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4912
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
With the recent improvement 3d6ffe76f8,
speedup by CACHE_ROM is reduced a lot.
On the other hand this makes coreboot run out of MTRRs depending on
system configuration, hence screwing up I/O access and cache
coherency in worst cases.
CACHE_ROM requires the user to sanity check their boot output because
the feature is brittle. The working configuration is dependent on I/O
hole size, ram size, and chipset. Because of this the current
implementation can leave a system configured in an inconsistent state
leading to unexpected results such as poor performance and/or
inconsistent cache-coherency
Remove this as a buggy feature until we figure out how to do it properly
if necessary.
Change-Id: I858d78a907bf042fcc21fdf7a2bf899e9f6b591d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5146
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
As rambi has the ChromeOS EC on it the EC needs to
be configured properly. Do this along with updating the
ChromeOS support for passing on write protect state, recovery
mode and developer mode.
BUG=chrome-os-partner:23387
BRANCH=None
TEST=Built and booted to depthcharge. EC software sync appears to
work correctly. Additionaly, 'mainboard_ec_init' appears in
the console output.
Change-Id: I40c5c9410b4acaba662c2b18b261dd4514a7410a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174714
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4905
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There's some baked in assumptions internal to coreboot
that the BSP's cpu device exists in the device tree. Therefore
provide one in the device tree.
BUG=chrome-os-partner:22862
BRANCH=None
TEST=Compiled and booted with other changes.
Change-Id: I22ba10964760ee8efbc5bbd5d4ce65daf31b3839
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173702
Reviewed-on: http://review.coreboot.org/4887
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The ram_id[2:0] signals have stuffing options for pull up/down
with values of 10K. However, the default pulldown values for these
pads are 20K. Therefore, one can't read a high value because of
the high voltage threshold is 0.65 * Vref. Therefore the high
signals are marginal at best.
Fix this issue by disabling the internal pull for the pads connected
to ram_id[2:0].
BUG=chrome-os-partner:23350
BRANCH=None
TEST=Built and checked that ram_id[2:0] is properly read now.
Change-Id: Ib414d5798b472574337d1b71b87a4cf92f40c762
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173211
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-on: http://review.coreboot.org/4885
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
CHROMEOS is the meant to be selected by the user. The correct variable
for a mainboard to select is MAINBOARD_HAS_CHROMEOS. This will then
default to a CHROMEOS build, but when the mainboard selects CHROMEOS,
the user can no longer disable CHROMEOS.
Change-Id: I78fb15a0a9fef733e2de064d6c09cf774b7bce78
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5218
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
spd.bin can reside anywhere in CBFS, and we only use CBFS APIs to
access and read it. As such, there is no need to hardcode it, and it
can collide with mrc.bin or mrc.cache on some boards. Do not use a
specific position for spd.bin, but instead let cbfstool find the
optimal placement.
Change-Id: I496094d3c0de708813494095b7ac4be8addb4112
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
If the SerialIO devices are put into ACPI mode then it is possible
to use ACPI to instantiate the touchpad in the kernel without
needing to have a platform level driver to do the binding.
This is the "new way" of describing on-board I2C devices and the
upstream kernel is starting to add ACPI IDs to drivers so they can
be used in this fashion. For the Cypress touchpad use a generic
ACPI ID of "CYPA0000" to describe it.
In order to support the proper scoping of the touchpad device under
the appropriate I2C controller device the mainboard.asl file needs
to be included after pch.asl so the I2C device exists.
Change-Id: I81e053d27be478f3a19b6f9b13cd2b4fabcb88c0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5194
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are currently 4 SKUs:
0b000 - 4GiB total - 2 x 2GiB Micron MT41K256M16HA-125:E 1600MHz
0b001 - 4GiB total - 2 x 2GiB Hynix H5TC4G63AFR-PBA 1600MHz
0b010 - 2GiB total - 2 x 1GiB Micron MT41K128M16JT-125:K 1600MHz
0b011 - 2GiB total - 2 x 1GiB Hynix H5TC2G63FFR-PBA 1600MHz
Add each of the 4 spds to the build, and use the proper
parameters to MRC to use the in-memory SPD information.
BUG=chrome-os-partner:22865
BRANCH=None
TEST=Built. Noted 1024 bytes of SPD content.
Change-Id: Ife96650f9b0032b6bd0d1bdd63b8970e29868365
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172280
Reviewed-on: http://review.coreboot.org/4872
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The calculations for static allocation are no longer valid.
Change-Id: I6740cdcec789abddf78485a0edaf24882ef8c2a5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4569
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Based on info from commit messages (most devel/eval boards are mentioned
as such in commit message) and information from vendor sites (mostly based
on form factor).
Classification for siemens/sitemp_g1p1 is based on info by Nico Huber.
For Google boards based on info from ML posted by Aaron Durbin.
Remaining unclassified board is:
google/pit
For which very little info is available publically.
Change-Id: I12dfff4c629811a48cfc77be27bdc5081530b8f6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4759
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
The replacement function confirms CBMEM TOC is wiped clean on power
cycles and resets. It also introduces compatibility interface to ease
up transition to DYNAMIC_CBMEM.
Change-Id: Ic5445c5bff4aff22a43821f3064f2df458b9f250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4668
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Do not expose options that are unsupported by the board. I tried for
a couple of days to see why hyperthreading wasn't working. It's not
supported by the CPU. The same applies to the baud_rate option. It
makes no sense to expose it to userspace via nvramtool.
Change-Id: I89b91820616d92fb4db20bf77f4b7f48a70353d5
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4697
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
board_info.txt is a file to be used by board-status to add
some useful info to the generated table like flash chip type.
This series is autogenerated from wiki page Supported_Motherboards.
Change-Id: Ie2bda900713ef4883134477163320936c84c34f5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4701
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
One of arguments to cbfs_get_file_content was missing.
Change-Id: Icb4ef26f18d63c133bc32f1c62a524edee0621ea
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4696
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Delay the copying of MRC cache data from CAR to CBMEM until after
sdram_initialize() returns and cbmem_initialize() completes.
Calling cbmem_initialize() twice would complicate the decision logic
of when CBMEM area needs to be wiped clean.
Change-Id: Ic59e94cb2436293efc47b52f7418f5dbf76c714a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4666
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Ability to choose compatibility mode is interesting for testing payloads and
OS for compatibility with older systems.
As per comments
"ide_legacy_combined # TODO: Does nothing since
generations, remove from sb code?"
The "combined" mode was removed. It wasn't used by any mobo and the code for
it is almost identical to IDE one other than few bits relating to interrupt
handling and ISA mode.
Change-Id: I407a8fac753b513812a86bef5abcf39c6d81472e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Number one reason to use cbfs_get_file was to get file length.
With previous patch no more need for this.
Change-Id: I330dda914d800c991757c5967b11963276ba9e00
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4674
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
THis reduces risks of bufer overflows.
Change-Id: I77f80e76efec16ac0a0af83d76430a8126a7602d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The main purpose of option rom is to supply int* handlers.
But supplying those is outside of coreboot scope and if someone needs those
they should run SeaBIOS anyway which runs the option roms wonderfully.
Running VGA oprom is kept because they're needed to init graphics.
This patch still keeps the options to include the option roms to make them
available to SeaBIOS.
Change-Id: I646334cf88094d3bf8f527779a68a07e0b4b93ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4545
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
Configure the pins for the UART unconditionally in the mainboard code (when we
know which UART to configure) instead of in the UART driver. This also means
the UART will work if later software wants to use it without setting up the
pins.
Built and booted on pit with the serial turned off and some serial init
in the kernel decompression stub fixed.
Change-Id: Icab5755e4f935f52d44b9cb3b43d1cb62acce08f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65299
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4457
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch implements the basic infrastructure required to use the USB
A-A firmware upload feature on Exynos5 processors with Coreboot. It will
require a corresponding host-side script that activates the feature and
uploads the correct image parts in the correct order to harcoded target
addresses, as described in the comments of alternate_cbfs.c.
Also fixes a bug in the Google Snow mainboard where it would not
correctly initialize the pinmux configuration for the SPI flash bus.
During a normal SPI boot the IROM would already do that for you, but
when booting from USB you have to do it yourself.
Change-Id: I40a39f8f5d1d70b58dbf258015c1653a27097d67
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64875
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4456
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Change-Id: I6729a139091b40d8fd9ba2aa7a8c4e14216d95c5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64879
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4440
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The memory corruption problem in Exynos suspend/resume process is caused by two
things together: PHY_RESET and MRS command.
After stop sending MRS on resume, we can now remove the workaround of skipping
PHY_RESET.
Change-Id: I64acc27c1d2bb549ae6ad7d32ecda94b0355972c
Reviewed-on: https://gerrit.chromium.org/gerrit/64736
Tested-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/4433
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This includes the new dp code, which is better, and the fimd code,
which is changed and improved. We took the chance to remove un-needed
files, and also to remove some foolish u-boot habits, but not all of
them. That will take time.
With these changes we get graphics.
Since the only mainboards we have with 16 bit graphics are 5:6:5,
adjust edid.c to just use that format. If at some future time we need
4:4:4, which seems unlikely, we'll need to add a function to adjust
the lb_framebuffer. Note that you can't just divine this from the EDID,
as the graphics pipe format need not match the actual final format used.
The EDID reading works. We've been requested to support hard-coded
EDIDs and that will come in the next revision. Currently the hard-coded
EDID is ignored for testing.
Change-Id: Ib4d06dc3388ab90c834f94808a51133e5b515a4d
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64240
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4432
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This update the PMIC write sequence to be correct for newer board
revisions.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I2210b0d1945fb19c96a674c8fad1b0ff5a4a381e
Reviewed-on: https://gerrit.chromium.org/gerrit/64304
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4427
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This corrects a minor typo used for a part number.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I8583cbfc3b4a6c3ad06419f5aab3ba7a8f685575
Reviewed-on: https://gerrit.chromium.org/gerrit/64301
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4424
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In a previous commit the contents of wakeup_need_reset were removed because
the GPIO it referred to wasn't connected to anything on pit. I didn't realize
at that time that that could have been because we hadn't tried getting
suspend/resume working on pit and hadn't updated that file. On snow, the GPIO
is the recovery mode pin. This change updates pit to have the right GPIO,
kirby to read that GPIO, and makes the comments for both pit and kirby more
explicit and spells out the fact that this is the recovery mode GPIO.
Having a check here at all may still be a holdover from snow that isn't
applicable to pit or kirby, but since there is a parallel as far as the
recovery mode GPIO we might as well make them match while waiting for more
information.
Change-Id: Ic1f3f605a0fddf89e8f5668c7a8df30bdfb91d94
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64164
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4421
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Like on kirby, this header had a single constant in it that was actually used.
This change moves that constant inline and gets rid of the header file.
Change-Id: Ibe380396f72fddb121fb6ceb3cee24f1b9a85738
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64163
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4420
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
1. Kirby doesn't have a backlight enable GPIO on the AP since that's handled
entirely by the DP-to-LVDS bridge.
2. There is no tps65090 on the other side of the EC who's settings need to be
adjusted. If we need to turn on the LCD or backlight power manually, it will
have to be done in a different way.
3. The PMIC doesn't provide a 32KHz output for the audio codec.
Change-Id: Iadc5f3aec4818805edf3f2517da9e6fee87085dc
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63883
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4413
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The function in wakeup.c isn't applicable on kirby. The only constant in
exynos5420.h that was used was the speed of the 4th i2c bus. Instead of having
a whole header file for that one constant used in one place, the constant is
just moved inline along with the comment it had in the header.
Change-Id: I5ad50c5eeaecbbf7865d76afb31a12d36c3371ee
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63882
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4412
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Change-Id: Ic78c65486816015f7574a13affc6e54acbbea73e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63875
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4411
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
... In order to do this, the graphics memory has to move into
the resource allocator and out of CBMEM.
Change-Id: I565c3d6dea747822fbabf6f3845232d4adfbf333
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63657
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4391
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
... In order to do this, the graphics memory has to move into
the resource allocator and out of CBMEM.
Change-Id: I7396da4a7068404b0d2e4d308becab4dd6ea59bb
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59326
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4390
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It's not needed and it's a potential problem source.
Change-Id: Ic4cafe74e7fc3a9031d852895ad7fd5e5cd64d11
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/62279
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4410
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Moved a lot of code from i915io.c to intel_dp.c with specific function calls
Change-Id: Ib2ed52b4f73ee0076e2dd68a26541e5bbe1366bc
Reviewed-on: https://gerrit.chromium.org/gerrit/63950
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4429
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Depending upon the values decoded from edid, the function decides the appropriate bits to
be set in flags parameter (Important for fastboot to work correctly in kernel)
Change-Id: I3b0f914dc2b0fd887eb6a1f706f87b87c86ff856
Reviewed-on: https://gerrit.chromium.org/gerrit/64265
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4423
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Also, used this attribute in the calculation of htotal and other registers
Added intel_dp_* functions for m,n registers and dimension register calculations
Change-Id: I99dd7156700d59b0b4c85e34c9aa1c6408c7f31a
Reviewed-on: https://gerrit.chromium.org/gerrit/64001
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4422
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Works fine with all three panels with the change of 6 bits per color.
Change-Id: Ia47d152e62d1879150d8cf9a6657b62007ef5c0e
Reviewed-on: https://gerrit.chromium.org/gerrit/63762
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4402
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Empirical testing shows that 0x5 is the optimal setting for DTLE DATA /
EDGE on Peppy.
Change-Id: I273a3a68be97b3eb7c2ee2071e5de1ef7bf7f2d9
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65717
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4476
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The SMI handler code was setting S3 wake events when going
into S5 and enabling a key press to wake the system.
Change-Id: I6413ef1341e0149187df9f4f7e0c314d4c9e9c6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65323
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4459
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Boot on falco and look in /sys/firmware/log for
the string "PCIe Root Port 1 ASPM is enabled"
Change-Id: Ie2111e4bb70411aa697dc63c0c11f13fbe66c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65315
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4454
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
CLKOUT for PCIE ports 1-5 and CLKOUT_XDP are not used
and can be disabled.
I couldn't test this directly without a scope so instead I
used a modified commit that also disabled PCIe Port 0 and
saw that that correctly disabled the WLAN port.
Change-Id: I0f996e90f0ae42780de3a0c8dc5db00ec600748b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4451
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the EC requests the host to throttle (for charging or thermal
related reasons) the package power consumption will be limited.
Right now this is set at 12W but that is somewhat arbitrary and may
need tuning.
1) define the THRT method in \_TZ scope for EC to call
2) enable SCI events for throttle start and stop
3) define the power limit at 12W and set it in NVS
1) Enable CONFIG_ACPI_DEBUG=y in the kernel
2) Enable the Debug object event in acpi module
acpi.debug_layer=0x7f acpi.debug_level=0x2f
3) Using EC console generate host event for throttle start
> hostevent set 0x20000
4) Check dmesg for throttle start events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q12] (Node ffff8801002c5988)
[ACPI Debug] String [0x12] "EC: THROTTLE START"
[ACPI Debug] String [0x10] "Enable PL1 Limit"
5) Using EC console generate host event for throttle stop
> hostevent set 0x40000
6) Check dmesg for throttle stop events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q13] (Node ffff8801002c59b0)
[ACPI Debug] String [0x11] "EC: THROTTLE STOP"
[ACPI Debug] String [0x11] "Disable PL1 Limit"
Change-Id: I39b53a5e8abc2892846bcd214a333fe204c6da9b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63989
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4416
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the edid data structure changed a while ago, it caused hangs on snow
which were fixed by adding those missing members. Unfortunately we didn't
realize that pit needed the same fix.
Change-Id: I81780b8135b99b2e24af723e703b9befff7b5ef0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63646
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4389
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
That speed is used with U-Boot instead of the more conservative 500 KHz.
Change-Id: Ie9d79db3b52b88c1f3bfec1745634ae6bdc9f4ee
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63193
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4386
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Now that the rtd2132 device has the full settings the
panel timings need to be implemented. Sadly, the Tx timings
in the rtd2132 aren't 1:1 with the panel's Tx timings. Below
is the table equivalent:
RTD2132 | Falco Panel
--------+------------
T1 | T2
--------+------------
T2 | T8+T10+T12
--------+------------
T3 | T14
--------+------------
T4 | T15
--------+------------
T5 | T9+T11+T13
--------+------------
T6 | T3
--------+------------
T7 | T4
--------+------------
Change-Id: I10a3ad475d6b9485a707eb49e31afd197fc8d24d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65858
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4472
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The PWM is controlled externally from the APU.
Change-Id: Ia5130d7616991a78dfde44043a60a32cee4f145c
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61513
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4363
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
What gets written into the parade is highly mainboard-dependent.
So the parade_writes array needs to be there.
Change-Id: Ia382d9bf1929e67b7c14d7a09f5461b71866a16b
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61486
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4362
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
This is a clone of a Falco change:
I1a0df80dd47fdbd535aca7a9d49253794c480606.
Change-Id: I625dfbb228d1f293b880a52dfe552842d55a17d1
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63220
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4383
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
... based on the EDID detailed timing values for
pixel_clock and link_clock.
Two undocumented registers 0x6f040 and 0x6f044 correspond to link_m and link_n
respectively. Other two undocumented registers 0x6f030 and 0x6f034 correspond
to data_m and data_n respectively.
Calculations are based on the intel_link_compute_m_n from linux kernel.
Currently, the value for 0x6f030 does not come up right with our calculations.
Hence, set to hard-coded value.
Change-Id: I40ff411729d0a61759164c3c1098504973f9cf5e
Reviewed-on: https://gerrit.chromium.org/gerrit/62915
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4381
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This code is left over from what the VBIOS did; It is redundant.
Change-Id: I321c867c81ec8b4d5e10f8b51b872cecb3082d97
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/62290
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4380
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Turn on the pei_data flag that will instruct the reference code
binary to route all USB ports to the XHCI controller on resume and
disable the EHCI controller(s).
Change-Id: I2f2ed853a6d17f90ea524bc516f3e78079222739
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63798
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4404
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
SATA is routed to PIRQG which should be interrupt 22
and not interrupt 21. The kernel uses MSI with this
device so this is only seen when booting with pci=nomsi
Change-Id: Ic90ca2c561fc4c53ec1d395c05872222c65ff98a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4398
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Since these boards do not support C10 we should not bother
advertising that state in the ACPI _CST.
Instead use this map:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Change-Id: I37eb02bf9555c74e957316a1ba9778eb2b6ee128
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62898
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4377
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The management engine is slow, requiring at least 500ms between
when the Dram Init Done message is sent (right after memory training)
to when the MBP will report that it is successfully cleared and
that the ME can finally be sent the EOP message.
Currently this is adding 100-150ms to the boot time. If we defer
waiting for the MBP Clear indicator until the finalize step we
can gain back that lost time.
boot on falco with SMI debugging enabled to
ensure that the ME is locked down in the finalize step:
Finalizing Coreboot
SMI# #0
SMI_STS: PM1 APM
ME: MBP cleared
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
Change-Id: Icab4c8c8e00eea67bed5e8154d91a1eb48a492d1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4375
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This reverts commit ff81f50f0e4c068b64c4a5c7f5244196ecd24965.
Deferring this step until the finalize stage will allow us
to defer waiting for the MBP clear indicator and speeding
up the boot.
Change-Id: Ib8edffd06689e72875830cd68b5aedb7ac3b0559
Reviewed-on: https://gerrit.chromium.org/gerrit/62631
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4373
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The intel_ddi.c change I thought should be in but I don't see it. It just adds two functions back
that we need.
There are two new files for slippy annotated with comments about how it needs to evolve.
That said, this code has been tested on 3 different panels. Both dev and non-dev usages work.
physbase initialization to static value removed.
Moved spin calls to intel_dp_*
Change-Id: I0480af45c21c7dedcaff7e8be729f0eb554ec78a
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61136
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4370
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Peppy SPD table has 4GB configurations followed by 2GB configurations.
Current implementation does remapping to point 2GB configuration to the
same SPD index as the 4GB. This is different than Falco, which simply
duplicates the SPD data for all configurations. To simplify probing in
mosys, copy the Falco implementation of duplicating SPD data.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Idb185a437f3cf4f40d2dae1ae59c30235df8f489
Reviewed-on: https://gerrit.chromium.org/gerrit/61847
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4369
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The EC temperature sensors were renumbered and now PECI
is at index 0.
1) boot on falco
2) check /sys/class/thermal/thermal_zone0/temp
3) check 'temps' on ec console
Change-Id: Idde1457c42c80850b5b8ac22781060ed9b224d13
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61896
Reviewed-on: http://review.coreboot.org/4367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This may need further tuning but will start at 1.0%.
boot on falco and check /sys/firmware/log
localhost ~ # grep RTD2132 /sys/firmware/log
RTD2132: Enable 1.0% Spread Spectrum
I2C: 01:35 (Realtek RTD2132 LVDS Bridge)
Change-Id: I96e1c14dbc6a7bfaf1c8deb1806c48bf2fd3e32a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61895
Reviewed-on: http://review.coreboot.org/4366
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The drivers in the kernel expect the devices using gpios
to generate interrupts to be edge sensitive. Make it so.
Change-Id: I920ef621682d33ba081f737e97f0239f903db2f7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61678
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4361
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The drivers are designed to work with an edge triggered interrupt.
Change-Id: I35a121ecfb6409bb9049f4d1e034185bb3bb7557
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4360
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
Change-Id: I1a0df80dd47fdbd535aca7a9d49253794c480606
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61421
Reviewed-on: http://review.coreboot.org/4358
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
To configure source clocks on Exynos 5420 for MMC drivers.
Some registers are different from the 5250. FSYS now has two parts
and MMC uses FSYS2. The MMC block uses MPLL as the clock source.
The "high-speed" MMC interface runs as 52MHz, so divider is set
accordingly.
Also, the MMC driver has changed from MSHCI (Mobile Storage Host Controller
Interface) to DWMCI (DesignWare MMC Controller Interface).
Change-Id: I9ba9cf43e2f2dcd9da747888c0c7676bd545177b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60858
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4354
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Make use of google_chromeec_get_board_version to determine board
version, and apply proper RAM_ID table to load correct SPD.
Change-Id: I6a2d54759cf2ce98bf53df0db396c6e09368c714
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61192
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4353
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update peppy's verb tables for the Realtek ALC283 Audio Codec.
ALC283 Configuration:
Digital Mic - NID 12h: Disabled
Speakers - NID 14h: Enabled
Mono out - NID 17h: Disabled
Mic 1 - NID 18h: Disabled
Mic 2 - NID 19h: Headphone Jack
Line1 - NID 1Ah: Internal Mic
Line2 - NID 1Bh: Disabled
PCBEEP - NID 1Dh: Enabled
SPDIF - NID 1Eh: Disabled
HP-OUT - NID 21h: Headphone Jack
Mic 1 doesn't seem to really be available, but the documentation
refers to NID 18h as MIC1, so it's being disabled as it's not
being used. The onboard microphone has been moved to line 1.
I had my peppy modified to attach the mic to line1 and mic1 now
works with this patch. Mic2 looks harder to rework, so I think
that will have to wait for the DVT boards.
Change-Id: I7d6ce6b428806b6aed1d36e7e25302fa5ae14b21
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58880
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4352
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
USB2 Port A set to 6.4" and Back Panel
USB2 Port B set to 5.2" and Back Panel
USB2 Port C set to 12.3" and Internal
Other devices all set to Internal.
build and boot on falco and check settings.
Based on the config settings all ports end up with
tuning param 1 == 5 and param 2 == 2
U2ECR[0] = 0x00059501
U2ECR[1] = 0x00059501
U2ECR[2] = 0x00059501
U2ECR[3] = 0x00059501
U2ECR[4] = 0x00059501
U2ECR[5] = 0x00059501
U2ECR[6] = 0x00059501
U2ECR[7] = 0x00059e01
Change-Id: I6b9e6df2679036a501355e6b389a486a6f178f99
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61297
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This CPU does not support Configurable TDP and so far does
not need to use Controllable TDP.
Change-Id: I15599cd4e6890dd5c9d9f99bc4e95307a8dcc827
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60657
Reviewed-on: http://review.coreboot.org/4347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The is_resume comment is wrong for this board. It only applies
to the older 5250 cpu. In fact, the is_resume parameter
is not needed for ddr init and will likely be removed soon.
Change-Id: I4e3c92fcaaa75d3c9223d90acccf053f61406307
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60103
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4342
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some new fields were added to the edid data structure, and the edid code was
changed to put estimated values into those fields which were ultimately passed
into depthcharge or other payloads. On snow we do things different and just
declare an edid structure statically which didn't have those members. The rows
and columns of the graphics console were 0, and that confused the framebuffer
driver and made it loop forever.
Change-Id: I6ca3bd948482b347a6a981e83b82b10dca995e5e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61057
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4341
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Update RAM_ID table.
- Add DEVSLP0 signal to NGFF SATA port.
Note: After this change, old Micron 2GB boards will no longer boot.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Id68a1d6ace2702cca9c37305726cd55a0bde5005
Reviewed-on: https://gerrit.chromium.org/gerrit/60167
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Limit power to 12W at 73C and remove limit at 68C.
To have the CPU consume maximum power it is necessary to stress
both the CPU and the GPU. Bastion (chrome.supergiantgames.com)
and/or webglsamples.googlecode.com can be useful for this.
Testing this properly requires a script to report the running
average power readings. The watch_power.sh script is attached
to this issue in the partner tracker.
1) Run watch_power.sh continuously:
localhost ~ # watch -n 0 bash -e /tmp/watch_power.sh
2) Start Bastion (or other stress apps). The power draw should
be close to 15W if under enough load.
3) Watch until temperature climbs above 73C and is caught by
the thermal zone 10 second poll, this can be sped up by blocking
or removing the fan.
4) The ACPI thermal zone states should change to reflect that
active[2] is now enabled and power consumption should drop to 12W.
5) Stop the stress apps and wait until the CPU cools off again,
enable the fan again if it was removed.
6) The ACPI thermal zone state should switch back to active[3].
Change-Id: Ie6714a8543d4f06edf8513086fc9c968273bdb23
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60545
Reviewed-on: http://review.coreboot.org/4335
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use a file in CBFS for keyboard layout and ethernet MAC instead
of scanning FMAP.
Change-Id: I7658c7c4e389deb20d7d8f57cce8b568efdc575d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4307
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The new edid functions support converting the edid to an lb_framebuffer.
Use them. Also, since panels seem to set bits per color instead of bits
per pixel, just force the right value in the edid struct.
Add helpful comment because people don't always believe we need to set
the pallette.
While we're at it, fix a problem that caused it to not compile.
Change-Id: I645edc4e442d9b96303d9e17f175458dc7ef28b6
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/57619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4327
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Don't force dev mode. Allow users to enter / exit dev mode as normal.
Change-Id: I168eb04a8ac102a8c4a1ca8936f78f62b001e0eb
Reviewed-on: https://gerrit.chromium.org/gerrit/59492
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4321
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On some systems there may be 2GB SKU that is the same as the
4GB SKU but just one channel of memory. In that case we need
to ensure that both copies of the same SPD source end up
populated by ensuring that repeated entries are included by
using $+ instead of $^.
Alternatively we could do the check inside romstage, but it
is already set to behave this way if the SPD gets populated
correctly.
I changed spd_index to 3 in falco romstage to force it to
pretend it was a 2GB config of the same memory, then booted
to ensure it was indeed limited to 2GB.
memcfg channel[0] config (00780008):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 2048 MB width x16 single rank, selected
DIMMB 0 MB width x16 single rank
memcfg channel[1] config (00600000):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 0 MB width x8 single rank, selected
DIMMB 0 MB width x8 single rank
Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59483
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These are based on the datasheet and I included the timing
values I used from the docs.
Change-Id: Ib75b2c5e50ac09d1e4cf9dd22229bb0f0a8965a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58540
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4234
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Currently, all Peppy boards w/ '000' SPD GPIOs have 2GB DRAM. Disable
the second DRAM channel based upon the GPIOs.
Need to change / confirm this for upcoming builds.
Change-Id: I7085ddecb80626cc0bed99ba7b174c6b80350696
Reviewed-on: https://gerrit.chromium.org/gerrit/58620
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4238
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
(Taken from I63ca00d6c94854f2b395eb736ce20792da5f8de2).
Change-Id: I9c7d1d1f1aaf7de33d0cec5f6daf648576ba8900
Reviewed-on: https://gerrit.chromium.org/gerrit/57289
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A quirk of the Kconfig used in coreboot is that config options
cannot be overriden by local config changes unless they have
a description string.
1) Add CONFIG_MAINBOARD_VENDOR="Custom" to local config
2) Build and flash coreboot
3) cat /sys/class/dmi/id/sys_vendor and look for "Custom"
Change-Id: I1b5f2124cd4a22c056c025143ae5bcaafa6b03f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59088
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4248
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
Also sync pin states from Falco initial commit.
Reference change: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Change-Id: I66e136d389d53a367436d816fa84dacdc8e86bad
Reviewed-on: https://gerrit.chromium.org/gerrit/58334
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/4247
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Set nid 0x12 instead of nid 0x05. The DMIC is on NIC 0x12.
Change-Id: Ifc883b65a50aeec6a6d3ad02fe8418f124e6241d
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4246
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Make the declaration and use of it conditional on the ELOG_GSMI Kconfig variable.
Change-Id: I2ef291d2f3e7d35545014e03ba8e0045da6050e5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3987
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
Google Chrome EC MKBP driver ready, id 'slippy_no_version'
Clearing the recovery request.
EC hash:7fea29992ef72e3e64d8ffe522aa1dfa68dcb44a2da96a4c19530ea1a0bd22c4
EC-RW hash address, size are 0xffa1cfe8, 32.
Hash = 727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
Expected hash:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
EC-RW firmware address, size are 0xffad000c, 57180.
VbEcSoftwareSync() - expected len = 57180
Computed hash of expected image:727e79934d9394184da496cebc27f7275b9d2d91079bf125d8f977a1f8aa4cde
VbEcSoftwareSync() updating EC-RW...
VbEcSoftwareSync() jumping to EC-RW
VbEcSoftwareSync() in RW; done
Change-Id: I63ca00d6c94854f2b395eb736ce20792da5f8de2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56821
Reviewed-on: http://review.coreboot.org/4208
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Set verbs to reflect the layout used for ALC283 in Falco,
which ends up being the same as Slippy.
Change-Id: I3dce4effefaa91ee5bdcbe2a8a3750ebc41376ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58196
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4232
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set verbs to reflect the layout used for the ALC283 in slippy.
install on slippy and check that headphone switch works
as does external mic.
Change-Id: I2d6bcda9cf8bbf49cbb6d2dbbe7f1a5adf315d8a
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57560
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4224
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Peppy RAM ID table is as follows:
000 41K256M16HA
001 H5TC4G63AFR
010 EDJ4216EFBG
Elpida SPD taken from Ib1e430cd390b4dbc013fc0802f1a59c1a0412577 by
dlaurie.
Change-Id: Iac156a2d25435514f28e2e73bef617d0fe2d90a1
Reviewed-on: https://gerrit.chromium.org/gerrit/56687
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Taken directly from slippy with only constant + string changes.
(Peppy port of I4172460d3b075bfd5bb22013a6225cf0e8f95b9c by dlaurie)
The following changes are required in a subsequent commit:
- Add Elpida SPD data.
- Update GPIO map.
- Remove iSSD power sequencing.
- Update USB port map.
Change-Id: I01dfb841f0e9186cf8a0a23f72e7be986a83be42
Reviewed-on: https://gerrit.chromium.org/gerrit/56513
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4200
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
RAM_ID indices have been changed and settled on a 2GB config
that will be the same DRAM chips but only used in one channel.
Change-Id: I444e655883ae045622ab3dfb964da4d7f86e1c0d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4198
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are placeholder values until we can configure for
the exact panel.
Change-Id: If40367c0e5f80d46d085c89b0edae60f1ccacdaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56808
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4197
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the onboard I2C devices for Falco trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
Change-Id: Ibe9687b2f7f41ead18353c3f650219fe6e94ae2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4191
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the onboard I2C devices for Slippy trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
tested on slippy with trackpad with additional
kernel changes to chromeos_laptop.c to initialize devices.
1) Ensure trackpad interrupt is functional and that there
is not a flood of ACPI SCI when trackpad does interrupt:
9: 1 0 0 0 IO-APIC-fasteoi acpi
37: 421 0 0 0 IO-APIC-fasteoi cyapa
2) Ensure that devices are exposed as wake capable:
Device S-state Status Sysfs node
TPAD S3 *enabled pnp:00:00
TSCR S3 *disabled pnp:00:01
3) Ensure that trackpad can wake from S3 by default, but
that it does not cause an immediate wake when entering suspend.
4) Ensure that trackpad can be disabled as a wake source with
echo TPAD > /proc/acpi/wakeup
Change-Id: Id562d20b54eeefec56040b8f70ef238911312628
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56622
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4190
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was provided by the vendor but I added the part number at
byte 128-143 so it can be identified when extracted by mosys.
Change-Id: Ib1e430cd390b4dbc013fc0802f1a59c1a0412577
Reviewed-on: https://gerrit.chromium.org/gerrit/56634
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4192
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Mainboards were defining their own SMBIOS type41
write function. Instead pull this into the generic
SMBIOS code and change the existing mainboards to
make use of it.
Change-Id: I3c8a95ca51fe2a3118dc8d1154011ccfed5fbcbc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4187
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These boards were returning 0 to indicate success when
the realmode handler expects it to return 1 to indicate
that it handled the interrupt.
Change-Id: I2baeaf8c2774fa7668a8b2f2d9ad698302eefb21
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50881
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4168
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The format of this function changed but was not updated in
all mainboards. This fixes all Sandybridge/Ivybridge boards.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Icdaae4d6d50884f6d7bce7a167d48cb1d4807010
Reviewed-on: https://gerrit.chromium.org/gerrit/48969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4135
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
SandyBridge raminit uses this CMOS option. If it is not declared, the build
fails when USE_OPTION_TABLE is selected.
Change-Id: I1ba1f994d4ea3824dc66e8f35d0b5b24b88d4dd6
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4269
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For all the current haswell boards enable the monotonic timer.
The ULT boards use the 24MHz MSR while the non-ULT boards use the
local apic.
Change-Id: I8b19f526a5a49e8467f296c566a2c4263bc5a863
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49763
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4148
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These are placeholder values until we can configure for
the exact panel.
Change-Id: Ibe88cc3588947366eb1728e5b3e1ab8c8be6dfe8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4196
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Minor tweaks to variable names in the slippy mainboard
that make it easier to base a new board from without
as much renaming.
Also properly set up the thermal variables for the
thermal zone that is defined in ACPI instead of using
the generic setup from WTM2.
Change-Id: I752c1a50bfdc06b6ddad95bd1331c6870b9f9df2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56328
Reviewed-on: http://review.coreboot.org/4183
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This will log and clear EC events so they do not take effect
when the SMI handler is enabled.
Change-Id: I5ef563f7cedc8977410cc3f69e2655fc4e14c9eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4178
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The SerialIO devices have specific requirements for PCI
interrupt mode to use PIRQ{E,F,G,H} that are not being met.
D21:F0 uses PIRQE, which must not be shared with other PCH
D21:F1-F6 share PIRQF, which must not be shared with other PCH
D23:F0 uses PIRQH, which must not be shared with other PCH
- Fix D20IR -> D20IP typo
- Remove D25/EHCI2 as it does not exist
- Reorder other interrupts to clear PIRQE/PIRQF/PIRQH
Check device interrupts in the kernel
0: IO-APIC-edge timer
1: IO-APIC-edge i8042
8: IO-APIC-edge rtc0
9: IO-APIC-fasteoi acpi
16: IO-APIC-fasteoi ath9k
18: IO-APIC-fasteoi i801_smbus
19: IO-APIC-fasteoi ehci_hcd:usb1
21: IO-APIC-fasteoi i2c-designware-pci--1, i2c-designware-pci--1
40: PCI-MSI-edge PCIe PME
41: PCI-MSI-edge i915
42: PCI-MSI-edge ahci
43: PCI-MSI-edge xhci_hcd
44: PCI-MSI-edge snd_hda_intel
Change-Id: Id4c08d11d2860f270c6387138acdc7d3d83a85b5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56028
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4176
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The dev screen was not displaying properly. With the
PWM values programmed the screen displays correctly.
Change-Id: I82b56a92e4168022082a2e519026977ee2ae0c9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51472
Reviewed-on: http://review.coreboot.org/4172
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The device at function 0 also needs to be enabled
or the kernel will ignore all other functions.
00:15.0 DMA controller: Intel Corporation Lynx Point-LP Low Power Sub-System DMA (rev 03)
00:15.1 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #0 (rev 03)
00:15.2 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #1 (rev 03)
Change-Id: I0e1bc7bb719756496c46664d66dc1b1cf2f4d1ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51370
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4171
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Without an LM10506-A the power sequencing for this
part needs to be done manually using GPIOs.
Change-Id: I842152e5f7c30c8dbe37df0c344935a659eb2887
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49648
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4150
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit de1fe7f655.
While things appeared to work, there were actually invalid references
to CAR storage after CAR was torn down on boards without
EARLY_CBMEM_INIT. It was discussed use of CAR_GLOBAL should be
restricted to boards that handle CAR migration properly.
Change-Id: I9969d2ea79c334a7f95a0dbb7c78065720e6ccae
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3968
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
If romstage does not make cbmem_initialize() call, linker should
optimize the code for CAR migration away.
This simplifies design of CBMEM console by a considerable amount.
As console buffer is now migrated within cbmem_initialize() call there
is no longer need for cbmemc_reinit() call made at end of romstage.
Change-Id: I8675ecaafb641fa02675e9ba3f374caa8e240f1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3916
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Assume EARLY_CBMEM_INIT=y everywhere and remove option from Kconfig.
If romstage does not make the cbmem_initialize() call, features like
COLLECT_TIMESTAMPS and early CBMEM_CONSOLE will execute during
romstage, but that data will get lost as no CAR migration is
executed.
Change-Id: I5615645ed0f5fd78fbc372cf5c3da71a3134dd85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3917
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This retrieves back the value stored with store_initial_timestamp()
in the bootblock for southbridge.
Change-Id: I377c823706c33ed65af023d20d2e4323edd31199
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3908
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Clean whitespace errors that have gotten past lint-stable-003-whitespace
and gerrit review.
Change-Id: Id76fc68e9d32d1b2b672d519b75cdc80cc4f1ad9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3920
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Function is always called with get_top_of_ram() - HIGH_MEMORY_SIZE
which equals cbmem_base, thus no need to pass it as a parameter.
Change-Id: If026cb567ff534716cd9200cdffa08b21ac0c162
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3564
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This helper function is for compatibility only for chipsets that do
not implement get_top_of_ram() to support early CBMEM.
Also remove references to globals high_tables_base and _size under
arch/ and from two ARMv7 boards.
Change-Id: I17eee30635a0368b2ada06e0698425c5ef0ecc53
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3902
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The Kconfig variable EXTERNAL_MRC_BLOB is not used.
Drop it.
Change-Id: I3caa5c2b6bcf5d2c13b6987da8ab3987bad0e506
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3829
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The display port bridge on pit is different from the one on snow and needs to
be initialized differently. Instead of waiting for the chip to come up on its
own and assert the hotplug detect, we need to access it over i2c and get it up
and running ourselves.
Change-Id: I4bc911cb8e4463edff7beabd2f356cb70ae9f507
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3723
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was removed from ramstage a little while ago and should have been removed
from here as well.
Change-Id: I6a40ed4a98bedac39e5492e4b1aed3427ab4e08b
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3720
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This appears to be needed, though we have no way to test yet.
Change-Id: I39033581011e056258193f2cdff78814361a8d55
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3719
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In resume path, if memory setup takes too long without setting PS_HOLD, EC watch
dog may power off or reboot the system. To prevent that, we should enable
PS_HOLD in same timing as cold boot - right before starting memory setup.
Change-Id: I5c294fa7ae015f8cff57b1fd81e5b80902647b15
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3718
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The functions which manipulated the tps65090 were removed a while ago because
it isn't accessible directly from the AP, it's on an I2C bus that has to be
accessed by the EC on our behalf. Now that that capability has been added, we
can rewrite the small portion of the the tps65090 we actually used but using
the EC passthrough commands.
Also, we should not be configuring the hardware display port hotplug detect
line since we're using it as a GPIO for other purposes. The GPIO we're using
instead defaults to being an input, but to be safe we should probably
explicitly configure it as one anyway.
Change-Id: I7f8a8a767e3cccb813513940a5feceea482982f5
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3717
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ChromeOS EC for peach_pit is connected to SPI2 bus, not I2C.
Change-Id: Ifeb8a626aa4fc3d3a181a7bc016e3f91be948ae5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3716
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Embedded Controller (EC) for Pit is connected via SPI2, and needs to be
configured before we can talk to it.
Change-Id: I1f8e921b4616f15951f3e5fae1ecbf116de4ba90
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3707
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4feabc448945c4664d3114c0c8afdad48338230a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3705
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
(forward ported from https://gerrit.chromium.org/gerrit/#/c/55554)
Change-Id: I5a20864689efd0c0149775e6d85b658e0cc6715c
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3697
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... this is needed for libpayload to talk to USB devices.
Change-Id: I7eb19003c9e96efb5fa7a3f97c7b15f3ef332687
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The GPIOs used by vboot and setting up the display and backlight were still
the ones for snow. This change updates them so they're correct for pit.
Change-Id: I06ba773da3af249efec723bb90c2e9e8075a777a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MAX_CPUS option is only used on x86 currently, so there's no reason to
have it in the pit config.
Change-Id: I270bbfd3aff781d88304791b1d9735777643caab
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3688
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
That part isn't used on pit.
Change-Id: I48f3a10f7e6eb89b1e9630d2372b6865b4c12a7f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3687
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On pit, the tps65090 is connected to the EC and has to be accessed by proxy.
Until we have that implemented, this change removes calls to tps69050 which
will never succeed, and stops compiling in the driver.
Change-Id: I7218f85f9f26623bd13aaaf8ded0638b3b2f874a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3686
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the setup_power() function to actually set up the PMIC
which is on this board (the MAX77802).
Change-Id: I9c6f21f183dacc0bca71277e681e670834412d78
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3680
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested and working. Gets us to ramstage.
Change-Id: Ib9ea4a6c912e8152246aaf4f1f084a4aa1626053
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The pinmux code for the exynos5250 was all bundled into a single, large
function which contained a switch statement that would set up the pins for
different peripherals within the SOC. There was also a "flags" parameter, the
meaning of which, if any, depended on which peripheral was being set up.
There are several problems with that approach. First, the code is inefficient
in both time and space. The caller knows which peripheral it wants to set up,
but that information is encoded in a constant which has to be unpacked within
the function before any action can be taken. If there were a function per
peripheral, that information would be implicit. Also, the compiler and linker
are forced to include the entire function with all its cases even if most of
them are never called. If each peripheral was a function, the unused ones
could be garbage collected.
Second, it would be possible to try to set up a peripheral which that function
doesn't know about, so there has to be additional error checking/handling. If
each peripheral had a function, the fact that there was a function to call at
all would imply that the call would be understood.
Third, the flags parameter is fairly opaque, usually doesn't do anything, and
sometimes has to have multiple values embedded in it. By having separate
functions, you can have only the parameters you actually want, give them
names that make sense, and pass in values directly.
Fourth, having one giant function pretends to be a generic, portable API, but
in reality, the only way it's useful is to call it with constants which are
specific to a particular implementation of that API. It's highly unlikely that
a bit of code will need to set up a peripheral but have no idea what that
peripheral actually is.
Call sights for the prior pinmux API have been updated. Also, pinmux
initialization within the i2c driver was moved to be in the board setup code
where it really probably belongs. The function block that implements the I2C
controller may be shared between multiple SOCs (and in fact is), and those
SOCs may have different pinmuxes (which they do).
Other places this same sort of change can be made are the pinmux code for the
5420, and the clock configuration code for both the 5250 and the 5420.
Change-Id: Ie9133a895e0dd861cb06a6d5f995b8770b6dc8cf
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3673
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5420. Don't
always print all of them per default.
Change-Id: I2152ab760e31a335dbcd9d6ad32cd1eaae4b89bc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3670
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already
known when that structure was put together. Eliminate the extra space,
and pass the single value instead of the structure.
Change-Id: I29bc17488539dbe695908e47f0b80c07e102e17d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/3666
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are hundreds of GPIOs on the Exynos5250. Don't
always print all of them per default.
Change-Id: Ie349f2a4117883302b743027ed13cc9705b804f8
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3661
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new code is stolen from U-Boot with little or no understanding of how it
works.
Change-Id: I3de7d25174072f6068d9d4fdaa308c0462296737
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Don't initialize console twice in the bootblock
- remove printk in memory init that would mess up the UART
- unconditionally run console_init() in romstage, as it is
also unconditionally run in the bootblock.
Change-Id: I983d011c6ca602445f447d17799c1b2a33e8bd1d
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With LynxPoint-LP the SCI GPE is no longer a GPIO
that is offset by 16. Remove the Add and fix up
the link definition so it is still accurate.
Change-Id: I091141183a09345b5ffe28365583e48019f9f5e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/3742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already known
when that structure was put together. Eliminate the extra space, and pass the
single value instead of the structure.
Change-Id: Ia6a41cefdf8b29fe7d68f9596a156eced6eb5df8
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3652
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Coreboot knows that, for the snow board, certain pins are to be connected to
bus controllers in the SOC and to the wires of a bus external to the SOC. It
can configure them as such and free its payload from having to know how to
set everything up.
Change-Id: I1bb127c810e9ee077afc4227a6f316eaa53d6498
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3650
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
- Guard console_init() with CONFIG_EARLY_CONSOLE in bootblock
- Don't initialize console twice in the bootblock
- remove printk in memory init that would mess up the UART
- unconditionally run console_init() in romstage, as it is
also unconditionally run in the bootblock.
Change-Id: I8f0d60877433162367074d0e55e01f935fd81f8e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3647
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adds a pit mainboard which is mostly a copy of snow, except that
mentions of the 5250 were replaced with the 5420, and mentions of snow were
replaced with pit.
Change-Id: I8eb0ce379eb2fa353bb88d5656a0c5e2290afbf0
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change creates an exynos5420 directory with code that will eventually
implement support for the exynos5420 cpu from Samsung. Currently it's a copy
of the exynos5250 directory with the name changed. There are going to be some
problems where headers in src/cpu/samsung/exynos-common include headers in the
exynos5250 directory directly.
Change-Id: Ia8d7244310d32499238bbc171c0c668ec48178e1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Exynos GPIO code has three different APIs that, unfortunately,
were widely used throughout the code base. This patch is cleaning
up the mess.
Change-Id: I09ccc7819fb892dbace9693c786dacc62f3f8eac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3643
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When starting the Exynos5250 port, a lot of unneeded u-boot code
was imported. This is an attempt to get rid of a lot of unneeded
code before the port is used as a basis for further ARM ports.
There is a lot more that can be done, including cleaning up the
5250's Kconfig file.
Change-Id: I2d88676c436eea4b21bcb62f40018af9fabb3016
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3642
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It turns out that the exynos5-common code previously imported from
u-boot is not common code at all but very specific to the 5250 and
not compatible with the 5450. Hence, unify the directories exynos5250
and exynos5-common. We will try to factor out common code while
progressing with the 5450 port.
Change-Id: Iab595e66fcd01eda8365c96fb8bef896f7602f03
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3641
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch unfortunately incorporates a number of changes,
all of which are making future ARM ports easier.
- drop cruft that came in with u-boot
- move serial console from mainboard Kconfig to Exynos Kconfig
- factor out non-board specific wakeup code
- move generic bootblock code from mainboard to Exynos
- actually call arch_cpu_init()
- remove dead code
- fix up copyright messages
- remove snow_ prefix from a lot of code to reduce the noise
when creating a new mainboard based on that code.
Change-Id: Ic05326edf5a7e1a691c5ff841a604cb9e351b562
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3640
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
... and drop the wrapper on ARMv7
Change-Id: If3ffe953cee9e61d4dcbb38f4e5e2ca74b628ccc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3639
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In ram stage, all code flow should be tied to the resource allocator.
Stuff that has to happen before everything else goes into the mainboard
enable function in mainboard.c. This patch empties the main() wrapper
around hardwaremain.c, allowing to get rid of this special case in the
ARM port.
Change-Id: Ide91a23f1043b64acf64471f180a2297f0f40d97
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3638
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add three functions to edid.c:
void set_vbe_mode_info_valid(struct edid *edid, uintptr_t fb_addr)
takes an edid and uintptr_t, and fills in a static lb_framebuffer struct
as well as setting the static vbe_valid to 1 unless some problem
is found in the edid. The intent here is that this could be called from
the native graphics setup code on both ARM and x86.
int vbe_mode_info_valid(void)
returns value of the static vbe_valid.
void fill_lb_framebuffer(struct lb_framebuffer *framebuffer)
copies the static edid_fb to lb_framebuffer.
There is now a common vbe.h in src/include, removed the two special ones.
In general, graphics in coreboot is a mess, but graphics is always a
mess. We don't have a clean way to try two different ways to turn on
a device and use the one that works. One battle at a time. Overall,
things are much better.
The best part: this code would also work for ARM, which also uses EDID.
Change-Id: Id23eb61498b331d44ab064b8fb4cb10f07cff7f3
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change all PCI configuration accesses to MMIO on all boards
with SandyBridge and IvyBridge. To enable MMIO style access,
add explicit PCI IO config write in the bootblock.
Change-Id: I8f957a80bf57df000897c5a080dd5ff131b1ec0d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3576
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Move/remove MMCONF_SUPPORT reference under mainboard Kconfig, as
that feature originates from northbridge and cannot be disabled
for a single mainboard.
Change-Id: I6d6861079876ddddaff90b10f18edb6936e93bd0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3589
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows other boards to have the same choice block without confusing
kconfig.
Change-Id: Iea5a7f2d1c263aa7992f504b832ca9c862833c3f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3293
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
it has been unused since 9 years or so, hence drop it.
Change-Id: I0706feb7b3f2ada8ecb92176a94f6a8df53eaaa1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3212
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This re-introduces 2fde966 (http://review.coreboot.org/#/c/3177/)
which was reverted due to unsatisfied dependencies.
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Change-Id: I8e60105629d9da68ed622e89209b3ef6c8e2445b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit 2fde9668b4
Somehow this got merged before its dependencies. 3190 must be merged first, followed by 3176. However 3190 will fail while this patch is in. So the situation can't correct itself.
Reverting this until the other two go in.
Change-Id: I176f37c12711849c96f1889eacad38c00a8142c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3195
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I14ebf75649d101491252c9aafea12f73ccf446b5
Reviewed-on: http://review.coreboot.org/3177
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's fine to always start timer even in suspend/resume mode, so we can
move the timer_start() back to the very beginning of boot procedure.
That provides more precise boot time information.
With that timer change, the wake up state test procedure can be simplified.
Verified by building and booting firmware image on Google/Snow successfully,
and then suspend-resume without problem (suspend_stress_test).
Change-Id: I0d739650dbff4eb3a75acbbf1e4356f2569b487d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3151
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The firmware media source (SPI1) is already initialized by Exynos iROM.
There is no need to do it again.
Verified by building and booting Google/Snow successfully.
Change-Id: I89390506aa825397c0d7e52ad7503f1cb808f7db
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3147
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "console_init" does initialize UART driver (which will setup peripheral and
pinmux) and print starting message. Duplicated initialization can be removed.
Also, console_init (from console.c) is always linked to bootblock (and will do
nothing if CONFIG_EARLY_CONSOLE is not defined) so it's safe to remove #ifdef.
Verified by building and booting on Google/Snow, with and without
CONFIG_EARLY_CONSOLE.
Change-Id: I0c6b4d4eb1a4e81af0f65bcb032978dfb945c63d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3150
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The DDR3 memory initialization (with "mem_reset" set on normal boot) will cause
resume to be unstable, especially when X is running. System may show X screen
for few seconds, then crash randomly and unable to recover - although text
console may still work for a while. Probably caused by corrupted memory pages.
'mem_reset' (which refers to RESET# in DDR3 spec) should be enabled according
to DDR3 spec. But it seems that on Exynos 5, memory can be initialized without
setting mem_reset for both normal boot and resume - at least no known failure
cases are found yet. So this can be a temporary workaround.
Verified by booting a Google/Snow device with X Window and ChromeOS, entering
browser session with fancy web pages, closing LID to suspend for 5 seconds, then
re-opening to resume. Suspend/resume worked as expected.
Also tried the "suspend_stress_test" with X running and finished 100 iterations
of suspend/resume test without failure.
Change-Id: I7185b362ce8b545fe77b35a552245736c89d465e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3148
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the suspend/resume feature into bootblock and romstage.
Note, resuming with X and touchpad driver may be still unstable.
Verified by building and booting successfully on Google/Snow, and then executing
the "suspend_stress_test" in text mode ("stop ui; suspend_stress_test") in
Chromium OS, passed at least 20 iterations.
Change-Id: I65681c42eeef2736e55bb906595f42a5b1dfdf11
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3102
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move board setup procedure to snow_setup_* functions, and Snow board-specific
(wakeup) code to snow_* for better function names and comments.
Verified by successfully building and booting on Google/Snow.
Change-Id: I2942d75064135093eeb1c1da188a005fd255111d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3130
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The "wakeup" procedure will be shared by bootblock and romstage for different
types of resume processes.
Note, this commit does not include changes in romstage/bootblock to enable
suspend/resume feature. Simply adding functions to handle suspend/resume.
Verified by successfully building and booting Google/Snow firmware image.
Change-Id: I17a256afb99f2f8b5e0eac3393cdf6959b239341
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3129
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To support suspend/resume, PHY control must be reset only on normal boot
path. So add a new param "mem_reset" to specify that.
Verified to boot successfully on Google/Snow.
Change-Id: Id49bc6c6239cf71a67ba091092dd3ebf18e83e33
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds support for display bring-up on Snow. It
includes framebuffer initialization and LCD enable functions.
Change-Id: I16e711c97e9d02c916824f621e2313297448732b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3116
Tested-by: build bot (Jenkins)
This PLL is unused and can be disabled to save about 250mW.
Change-Id: I1be37304d6ea5ff78696e05ad1023ce3c57f636c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3109
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just cleans up a few areas:
- Removed an unnecessary delay from exynos_dp_bridge_setup()
- The delay at the end of exynos_dp_bridge_init() is necessary, so
removed the comment suggesting that it might not be.
- Simplified exynos_dp_hotplug
Change-Id: I44150f5ef3958e333985440c1022b4f1544a93aa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3113
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables clock gating to save power on unused IPs.
Change-Id: I9ab2a2535ebb91bb4110390a6f055a67146bdbf9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3110
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables the thermal management unit (TMU) on Snow.
Change-Id: Idd76af40bf0a5408baf61ef2665fd52ae4e260ba
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3108
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This function isn't yet used for much, or perhaps anything, but where it
appears in the code it's ored with other values. Since we're not actually
retrieving anything, it might be best to return 0 so that the other values
that are being ored in can be expressed and this function can stay dormant
until it actually has something to do.
Change-Id: I6edc222a5c2d00ece2ecfad5191a615331eeaf16
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3098
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
We need to read it to report its value to the payload. The kernel will
reconfigure it as an external interrupt, but we'll make it a regular input
for now.
Change-Id: I019bd2c2731144d3b7bb53fad0c2c903874f616c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3096
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These names were inherited from chromeos.c where they've already been
fixed.
Change-Id: I7ad57b979b7b8f42f6bd68d1ecf887caba3fa3f1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3095
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
ARM doesn't use option ROMs, so this value doesn't make sense.
Change-Id: I1a0f0854e1dd4b9594ca0c147e590337520436da
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3094
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Got rid of a lot of #defines, some of which were converted to enums and
the rest which were eliminated entirely. Got rid of cruft in
get_developer_mode_switch and started using it for the dev mode GPIO.
Instead of a macro defining how many GPIOs are expected, now the code
actually counts the GPIOs as they're added.
Change-Id: I97b6b9f52a72d1276eb3cf36d7f9dd7b335b4d19
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3093
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Implement the get_recovery_mode_switch function using the newly added I2C
based Chrome EC support.
Change-Id: I9d0200629887f202edf017cba3222a7d7f5b053e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3092
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
The comment about the lid switch was left over from when this file was copied
from another board and was incorrect. Also fixed a capitalization
inconsistency.
Change-Id: Icefd19047971e13c08f615578e4a181e82a2997f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3091
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Google's Chrome EC can be installed on LPC or I2C bus, using different command
protocol. This commit adds I2C support for devices like Google/Snow.
Note: I2C interface cannot be automatically probed so the bus and chip number
must be explicitly set.
Verified by booting Google/Snow, with following console output:
Google Chrome EC: Hello got back 11223344 status (0)
Google Chrome EC: version:
ro: snow_v1.3.108-30f8374
rw: snow_v1.3.128-e35f60e
running image: 1
Change-Id: I8023eb96cf477755d277fd7991bdb7d9392f10f7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3074
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are not defined since commit »Drop HAVE_MAINBOARD_RESOURCES«
(1c5071d1) [1] but were unfortunately introduced again in new ports.
[1] http://review.coreboot.org/1414
Change-Id: I5eb61628141aefd08779615702d51ca155fa632a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2707
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This removes the wait_ms argument from the dp_controller_init(). The
only delay involved is a constant 60ms delay that happens if
everything else goes well. This delay is derived from the LCD spec
so there's no reason it should be baked into the controller code.
(This patch also has the side-effect of fixing a bug where we were
delaying on an undefined value for wait_ms).
Change-Id: I03aa19f2ac2f720524fcb7c795e10cc57f0a226e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3078
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a microsecond timer, its declaration, the function to start it,
and its usage. To start it, one calls timer_start(). From that point
on, one can call timer_us() to find microseconds since the timer was
started.
We show its use in the bootblock. You want it started very early.
Finally, the delay.h change having been (ironically) delayed, we
create time.h and have it hold one declaration, for the timer_us() and
timer_start() prototype.
We feel that these two functions should become the hardware specific
functions, allowing us to finally move udelay() into src/lib where it
belongs.
Change-Id: I19cbc2bb0089a3de88cfb94276266af38b9363c5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3073
Tested-by: build bot (Jenkins)
We need these to be inputs so they can be read when populating the coreboot
tables. It seems like a good idea to do this early to ensure that the input
gate capacitance has had a chance to charge, and if we decide to use
actually use that information during the ROM stage to do earlier RW
firmware selection.
It is not guarded by a ChromeOS config variable because those lines are
always intended to be input GPIOs, regardless of whether we're running
ChromeOS or not.
Change-Id: Id76008931b5081253737c6676980a1bdb476ac09
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3067
Tested-by: build bot (Jenkins)
Add basic edp support to the ramstage. Not working.
Change-Id: I15086e03417edca7426c214e67b51719d8ed9341
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3055
Tested-by: build bot (Jenkins)
This is a simpler device tree that is also more correct,
and has graphics settings as well.
Change-Id: I342d8be7dddb76e6992876c73f5c625c926977d3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3053
Tested-by: build bot (Jenkins)
This re-factors the Exynos5 I2C code to be simpler and use the
new API, and updates users accordingly.
- i2c_read() and i2c_write() functions updated to take bus number
as an argument.
- Get rid of the EEPROM_ADDR_OVERFLOW stuff in i2c_read() and
i2c_write(). If a chip needs special handling we should take care
of it elsewhere, not in every low-level i2c driver.
- All the confusing bus config functions eliminated. No more
i2c_set_early_config() or i2c_set_bus() or i2c_get_bus(). All this
is handled automatically when the caller does a transaction and
specifies the desired bus number.
- i2c_probe() eliminated. We're not a command-line utility.
- Let the compiler place static variables automatically. We don't need
any of this fancy manual data placement.
- Remove dead code while we're at it. This stuff was ported early on
and much of it was left commented out in case we needed it. Some
also includes nested macros which caused gcc to complain.
- Clean up #includes (no more common.h, woohoo!), replace debug() with
printk().
Change-Id: I8e1f974ea4c6c7db9f33b77bbc4fb16008ed0d2a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3044
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The existing header was imported along with the Exynos code and left
mostly unchanged. This is the first patch in a series intended to
replace the imported u-boot I2C API with a much simpler and cleaner
interface:
- We only need to expose i2c_read() and i2c_write() in our public API.
Everything else is board/chip-dependent and should remain hidden
away.
- i2c_read and i2c_write functions will take bus number as an arg
and we'll eliminate i2c_get_bus and i2c_set_bus. Those are prone to
error and end up cluttering the code since the user needs to save
the old bus number, set the new one, do the read/write, and restore
the old value (3 added steps to do a simple transaction).
- Stop setting default values for board-specific things like SPD
and RTC bus numbers (as if we always have an SPD or RTC on I2C).
- Death to all the trivial inline wrappers. And in case there was any
doubt, we really don't care about the MPC8xx. Though if we did then
we would not pollute the public API with its idiosyncrasies.
Change-Id: I4410a3c82ed5a6b2e80e3d8c0163464a9ca7c3b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3043
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves highly board-specific code out from the Exynos5250
power_init() into Snow's romstage.c. There's no reason the CPU-
specific code should care about which PMIC we are using and
which bus it is on.
Change-Id: I52313177395519cddcab11225fc23d5e50c4c4e3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3034
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was a first pass at display port support, we have
realized that it was ultimately a bad path. The display
hardware is intimately tied into a specific cpu and
mainboard combination, and the code has to be elsewhere.
The devicetree formatting is ugly, but it matters not:
it's changing soon.
Change-Id: Iddce54f9e7219a7569315565fac65afbbe0edd29
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3029
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There is a wildcard rule to include mainboard/fadt.c.
Change-Id: I7f59d6b241c683b62c2c41c5795e45184882635e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2940
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds a call to explicitly configure L2 cache (though defaults
should be set correctly).
Change-Id: I120e29c986918c2904a0332e46fcf9f1c5380d85
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2950
Reviewed-by: Gabe Black <gabe.black@gmail.com>
Tested-by: build bot (Jenkins)
Automatically select CACHE_ROM for all Google boards.
Tested by generating a config for the link board. CACHE_ROM
was selected and was unable to unselect it using
'make oldconfig'.
Change-Id: I8e34207e3929a020bb0280657f95ba7a000ad024
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2963
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit 9427ca151e
Looks like we were a bit too anxious to see this one get in. The devicetree.cb change seems to have broken things.
coreboot memory table:
0. 0000000050000000-000000005000ffff: RESERVED
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
2. 0000014004000000-00000140044007ff: RESERVED
Before this patch:
coreboot memory table:
0. 0000000040000000-00000000bfefffff: RAM
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
Change-Id: I618e4f1976265d56cfd6a61d0c5736c55a0f3cec
Reviewed-on: http://review.coreboot.org/2914
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This does NOT turn on the graphics.
The device tree has been changed enough so that, at the very least, the correct
functions are called at the correct time, with the correct paramaters. We
decided to yank the I2C entries as they did not obvious function and might
not even have been correct.
Not working, seemingly, but we need to add a 4M resource for
memory, and it seems it needs to be fixed at the address shown.
This address was chosen from current hardware.
We realized that the display code should be part of the cpu -- that's how
the hardware works!
Change-Id: Ied65a554f833566be817540702f79a02e7b6cb6e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2615
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This adds new MMU setup code. Most notably, this version uses
cbmem_add() to determine the translation table base address, which
in turn is necessary to ensure payloads which wipe memory can tell
which regions to wipe out.
TODOs:
- Finish cleaning up references to old cache/MMU stuff
- Add L2 setup (from exynos_cache.c)
- Set up ranges dynamically rather than in ramstage's main().
Change-Id: Iba5295a801e8058a3694e4ec5b94bbe9a69d3ee6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2877
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
coreboot tables are, unlike general system tables, a platform
independent concept. Hence, use the same code for coreboot table
generation on all platforms. lib/coreboot_tables.c is based
on the x86 version of the file, because some important fixes
were missed on the ARMv7 version lately.
Change-Id: Icc38baf609f10536a320d21ac64408bef44bb77d
Signed-off-by: Stefan Reinauer <reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/2863
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Force link speed on these platforms to 3 Gbps to defeat buggy SATA
drives.
Change-Id: Ia38a7c486fb1f4469cd67ca5244bbf61f877d556
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2823
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This code is taken from an EDID reader written at Red Hat.
The key function is
int decode_edid(unsigned char *edid, int size, struct edid *out)
Which takes a pointer to an EDID blob, and a size, and decodes it into
a machine-independent format in out, which may be used for driving
chipsets. The EDID blob might come for IO, or a compiled-in EDID
BLOB, or CBFS.
Also included are the changes needed to use the EDID code on Link.
Change-Id: I66b275b8ed28fd77cfa5978bdec1eeef9e9425f1
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a new state machine. It is more programmatic, in the
case of auxio, and has much more symbolic naming, and very few
"magic" numbers, except in the case of undocumented settings.
As before, the 'pre-computed' IO ops are encoded in the iodefs
table. A function, run, is passed and index into the table and
runs the ops.
A new operator, I, has been added. When the I operator is hit,
run() returns the index of the next operator in the table.
The i915lightup function runs the table. All the AUX channel ops
have been removed from the table, however, and are now called as
functions, using the previously committed auxio function.
The iodefs table has been grouped into blocks of ops, which end in
an I operator. As the lightup function progresses through startup,
and the run() returns, the lightup function performs aux channel
operations.
This code is symbolic enough, I hope, that it will make haswell
graphics bringup simpler.
i915io.c, and the core of the code in i915lightup.c, were
programatically generated, starting with IO logs from the DRM
startup code in the kernel. It is possible to apply the tools that
do this generation to newer IO logs from the kernel.
Change-Id: I8a8e121dc0d9674f0c6a866343b28e179a1e3d8a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2836
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a new operator, P, for the state machine, meaning
implement a palette fill.
Implement a function (palette) that fills the palette when the
P operator is hit.
This replaces 256 lines in the state machine table with 1.
Change-Id: I67d9219fe7de0ecf1fb9faf92130c00c9f5f8e88
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2835
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For full integration of FUI into coreboot, we need aux channel
communcations. The intel_dp.c is a file taken from Linux and is
used for aux channel comms. This file has been cut down to work
with coreboot. For now it is associated with the link mainboard
until we get a better handle on how this all fits together. This
code is almost certainly usable on other platforms in the long term.
But one step at a time.
Change-Id: I7be4c56e0a7903f3901ac86e12b28f3bdc0f7947
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2834
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a new API for cache maintenance operations. The idea is
to be more explicit about operations that are going on so it's easier
to manage branch predictor, cache, and TLB cleans and invalidations.
Also, this adds some operations that were missing but required early
on, such as branch predictor invalidation. Instruction and sync
barriers were wrong earlier as well since the imported API assumed
we compield with -march=armv5 (which we don't) and was missing
wrappers for the native ARMv7 ISB/DSB/DMB instructions.
For now, this is a start and it gives us something we can easily use
in libpayload for doing things like cleaning and invalidating dcache
when doing DMA transfers.
TODO:
- Set cache policy explicitly before re-enabling. Right now it's left
at default.
- Finish deprecating old cache maintenance API.
- We do an extra icache/dcache flush when going from bootblock to
romstage.
Change-Id: I7390981190e3213f4e1431f8e56746545c5cc7c9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2729
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a trivial error with the recovery mode GPIO index.
Change-Id: I7290c1e23cdddaf91c9021d4e4252c0c772b6eab
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2825
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
A fix to eliminate warnings when building romstage files with ChromeOS
compilers
Change-Id: Ia5d7bbdde3aa3439fd493f5795f2cc2bf4c4c187
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We're happy to announce coreboot support for the "Stout"
Chromebook, a.k.a Lenovo X131e Chromebook.
Change-Id: I9b995f8d0dd48e41c788b7c3d35b4fac5840e425
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2636
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1]
`CHIP_NAME` is unneeded for mainboards as the name is composed
automatically in `src/devices/root_device.c` from the strings in
Kconfig.
Unfortunately the ports for Google Butterfly, Link and Parrot as
as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop
it again too.
[1] http://review.coreboot.org/1635
Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Call the power_init() function. We appear to have forgotten about it
when deprecating lowlevel_init_subsystems(), but it didn't seem to
cause problems until we got to doing more interesting stuff recently.
There are some clean-ups to do from the original code, such as not
attempting to configure I2C from PMIC code, which we'll get around
to in follow-up patches.
(Credit to Gabe for spotting this)
Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2699
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is previously used exception code from libpayload.
On startup it installs and then tests an exception handler.
The test is an unaligned memory operation.
Yes, we've seen what might be exceptions in the ramstage, and
it makes sense to handle them. This code is identical in structure
and operation to the previously committed payload exception handler,
though we reserve the right to change it as circumstances require.
The remaining question is whether we need it in romstage.
Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2614
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This adds some real GPIO mappings where virtual GPIOs were used before.
Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are essential functions for setting up the display port and
framebuffer, and also enable such things as aux channel
communications. We do some very simple initialization in romstage,
mainly set a GPIO so that the graphics is powering up, but the complex
parts are done in the ramstage. This mirrors the way in which graphics
is done in the x86 size.
I've added a first pass at a real device, and put it in the mainboard
Kconfig, hoping for corrections. Because startup is so complex,
depending on device type, I've created a 'displayport' device that
removes some of the complexity and makes the flow *much* clearer. You
can actually follow the flow by looking at the code, which is not true
on other implementations. Since display port is perhaps the main port
used on these chips, that's a reasonable compromise. All parameters of
importance are now in the device tree.
Change-Id: I56400ec9016ecb8716ec5a5dae41fdfbfff4817a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2570
Tested-by: build bot (Jenkins)
Set up the clocks used for sound and turn on the sound clock.
Change-Id: Ic59bfa9ae87116299503e6d25aeefba98c842fb8
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2587
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The MMC0 on google/snow can run in 8 bit mode. To simplify driver development,
we thought disabling it (using zero, which runs in 1-bit / 4-bit mode) may help.
However, after some experiments in payload drivers, setting pinmux to 8 bit mode
can still allow MMC to run in 1-bit / 4-bit mode, so it's pretty safe to enable
8 bit mode by default for better performance.
Verified to boot on google/snow, and got MMC0 working.
Change-Id: Ic0acc723fe6a8aecf373429d3801beadd70815d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2585
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The SD/MMC interface on Exynos 5250 must be first configured with, GPIO, and
pinmux settings before it can be detected and used in ramstage / payload.
Verified on armv7/snow and successfully boot into ramstage.
Change-Id: I26669eaaa212ab51ca72e8b7712970639a24e5c5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's not used, and not needed.
Change-Id: Ifca92f3606ac58fc26e09676488c3add5d84ae79
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2548
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add two more GPIOs (total 6) as needed by the Google Snow laptop.
These are faking out settings for now. This code is tested and working.
Change-Id: I2077ffb8b85958eefdf54e19763d57cc1178ce89
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2538
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
These were not separable or it would have been two CLs.
Enable CHROMEOS configure option on snow. Write gpio support code for
the mainboard. Right now the GPIO just returns hard-wired values for
"virtual" GPIOs.
Add a chromeos.c file for snow, needed to build.
This is tested and creates gpio table entries that our hardware can use.
Lots still missing but we can now start to fill in the blanks, since
we have enabled CHROMEOS for this board. We are getting further into
the process of actually booting a real kernel.
Change-Id: I5fdc68b0b76f9b2172271e991e11bef16f5adb27
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2467
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Ladies and gentlemen, I'm very happy to announce coreboot support for
the latest and greatest Google Chromebook: The Chromebook Pixel.
See the link below for more information on the Chromebook Pixel, and
its exciting specs:
http://www.google.com/intl/en/chrome/devices/chromebooks.html#pixel
The device is running coreboot and open source firmware on the EC
(see ChromeEC commit for more information on that exciting topic)
Change-Id: I03d00cf391bbb1a32f330793fe9058493e088571
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2482
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At the request of Paul Menzel, I reran an
old classic of a coccinelle script:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I01da31b241585e361380f75aacf3deddb13d11c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch will cause the resource allocator to actually set aside
the memory resources using methods in the previous patch. The coreboot
table output will include "RAM" entries (there were none before):
coreboot memory table:
0. 0000000040400000-00000000bff001ff: RAM
1. 00000000bff00200-00000000bff00fff: CONFIGURATION TABLES
2. 00000000bff01000-00000000bfffffff: RAM
Change-Id: I5cd76e93fc232fdae1754253efb4e9269b3a20c0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2420
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
»Chromebook« is the official spelling [1]. So correct that with
the following command.
$ git grep -l ChromeBook | xargs sed -i s,ChromeBook,Chromebook,
The incorrect spelling was only used for the chip name.
[1] http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html#hp-pav
Change-Id: I9c19f399a3e3d36bd644ec375822daa384a14961
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2370
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was omitted earlier while we were debugging DRAM code (0a5bc7f).
It was likely broken due to inconsistent units earlier on. Now that
things are cleaned up and working, let's add it back in.
Change-Id: I2f356355c98b2896e2371fa63b9c9f20ae76d634
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2379
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These were left over from earlier debugging and are no longer
needed. They don't indicate any status or useful info (other
than which line of code has been executed). Error messages are
available in case something needs attention.
Change-Id: Ie09fac29c42908cb8924169e56d8927fb76f02da
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2386
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The commit introducing support for the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
contains the typo, which is corrected now.
Change-Id: I932f4cd248cac71c3ede39a7da97162e791827cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
Correct some whitespace inconsistencies introduced in the
following commit.
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
Change-Id: Ifeda7eb29ddf855cdfea41ddbd685441ede55756
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2374
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The commits adding support for the Google Parrot Chromebook
commit a7198b34cc
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Tue Dec 11 16:00:47 2012 -0800
Add support for Google Parrot Chromebook
Reviewed-on: http://review.coreboot.org/2026
and the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
had macros in `fadt.c` which were not aligned correctly and did
not adhere to the coding style which uses just one space after
`#define`. Fix this and use tabs instead of spaces everywhere.
Change-Id: I1422c57a3bdc2faa29d2a6e2064e4d3aeed0f1cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2375
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
We're happy to announce coreboot support for the "Butterfly"
Chromebook, a.k.a HP Pavilion Chromebook.
More information at:
http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html
This commit also includes support for the ENE KB3940Q embedded controller
running on Quanta's firmware.
Change-Id: I194f847a94005218ec04eeba091c3257ac459510
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2359
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
It was off by a few orders of magnitude. D'oh.
Change-Id: I9c8a3d5bd9ce261f914cfc7d05d86a1c61519b81
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
RAMBASE and RAMTOP are leftovers from the x86 port and do not apply
the same way on ARM platforms. On x86 they refer to the low memory
region where coreboot tables reside.
However on ARM we don't have such a region which is architecturally
defined. So instead we'll use the CPU-defined DRAM base address and
the mainboard-defined DRAM size.
This also has the pleasant side-effect of fixing the coreboot tables
to not clobber ramstage code...
Change-Id: I5548ecf05e82f9d9ecec8548fabdd99cc1e39c3b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2351
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves GPIO setup from chip-specific SPI code to mainboard-
specific bootblock code. This makes exynos_spi_open a bit more
generic so it can eventually be used for any SPI channel. This
also benefits CBFS since the user can set media->context to
to any set of SPI registers.
Change-Id: I2bcb9de370df0a79353c14b4d021b471ddebfacd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves the setting of SPI clock rate into romstage's main,
which allows us to eliminate a bunch of dependencies from the
bootblock (about 7KB worth).
Change-Id: I371499bb4af6a6aa838294bc56f9dbc21864957a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This cleans up Snow's trivial ramstage, gives it a coreboot table
address and calls hardwaremain().
Change-Id: I84c904bcfd57a5f9eb3969de8a496f01e43bc2f6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Note: this patch was originally introduced in 2308, but there were
some ordering issues so it was reverted.
Change-Id: Ibc91c0e26ea8881751fc088754f5c6161d011b68
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use same console initialization procedure for all ARM stages (bootblock,
romstage, and ramstage):
#include <console/console.h>
...
console_init()
...
printk(level, format, ...)
Verified to boot on armv7/snow with console messages in all stages.
Change-Id: Idd689219035e67450ea133838a2ca02f8d74557e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2301
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This reverts commit 9029f4b63f
This patch needs to go at the end of the UART patch set. Sorry 'bout the confusion!
Change-Id: I5702c7d6130daf95776f2c15d24e5d253691cefd
Reviewed-on: http://review.coreboot.org/2319
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Change-Id: Ic863e222871a157ba4279a673775b1e18c6eac0d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2308
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The power_init is not required on Exynos 5250 (snow) in bootblock stage. To get
a cleaner and faster bootblock, we can remove it.
Note, power_init internally calls max77686 and s3c24x0_i2c, so both files are
also removed.
Verified to boot on armv7/snow.
Change-Id: I5b15dfe5ac7bf4650565fea0afefc94a228ece29
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The I2C initialization (on component MAX77688) is already done in power_init, so
we should not need an explicit call inside bootblock.
Verified to boot on armv7/snow.
Change-Id: I68c248a8b5fee4ab838b2fb708649e112559cc41
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove duplicated / testing code and share more driver for bootblock, romstage
and ramstage.
The __PRE_RAM__ is now also defined in bootblock build stage, since bootblock is
executed before RAM is initialized.
Change-Id: I4f5469b1545631eee1cf9f2f5df93cbe3a58268b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2282
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
"SPL" from U-Boot is deprecated by bootblock in coreboot/arm, so we don't need
it anymore.
Change-Id: Id16877075d0b870839a10160073ad70777a2af0a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2297
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This attempts to clean out some dead code which was copy + pasted
into Snow's bootblock.c file, along with some unnecessary headers.
Change-Id: If9f157a52395a047c249a2a6385e0e8ddf310e59
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2291
Tested-by: build bot (Jenkins)
This patch moves ARM core and DRAM timing functions around to simplify
the dependencies for system_clock_init().
The original code was architected such that the system_clock_init()
function called other functions to obtain core and memory timings.
Due to the way memory timing information must be obtained on Snow,
which entails decoding platform-specific board straps, the bottom-
up approach resulted in having the low-level clock init code
implicitly depend on board and vendor-specific info:
main()
->system_clock_init()
-> get_arm_ratios()
-> CPU-specific code
-> clock_get_mem_timings()
-> board_get_revision()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
...then proceed to init clocks
...come back to main()
The new approach gathers all board and vendor-specific info in a
more appropriate location and passes it into system_clock_init():
main()
-> get_arm_ratios()
-> CPU-specific code
-> get_mem_timings()
-> board_get_config()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
-> system_clock_init()
...back to main()
Change-Id: Ie237ebff76fc2d8a4d2f4577a226ac3909e4d4e8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2271
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This gets rid of a bunch of duplicate I2C code in the bootblock.
Change-Id: I51f625a0f738cca4ed2453fbcb78092e4110bc7e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This gets rid of a bunch of copy + pasted GPIO code.
Change-Id: I548b2b5d63642a9da185eb7b34f80cbebf9b124f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This gets rid of a bunch of copy + pasted code from Exynos UART
files.
Change-Id: I9fbb6d79a40a338c9fdecd495544ff207909fd37
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2286
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Mainboards using `COREBOOT` as their OEM Table ID in their DSDT
header were copied from the same source and therefore had spaces
instead of a tab to align that comment for that header field. These
are mostly Intel based boards.
Fix that in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I299b955930dbd50b9717e8ff141ce8f3fd534e5f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2277
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Snow's AP, EC, PMU, and smarty battery share a bus. Both the AP and
EC can act as a master, so to avoid conflicts an arbitration
mechanism consisting of two GPIOs is used.
By default, the AP "owns" the bus unless it is off (in which case
the EC doesn't monitor the arbitration pins). This means the boot
firmware does not need to worry about these lines. The payload may
if it needs to communicate with the EC, though.
In any case, board-specific bus arbitration logic does not belong
in a low-level driver that is supposed to be generic for an entire
CPU family. If the payload needs to talk to the EC, we'll deal with
it there.
Change-Id: I0774d4592af2b21b6ad668441532c5ceab988404
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2272
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes some duplicate code from Snow's mainboard bootblock
by utilizing the bootblock build class.
Change-Id: I153247370a8c5127260082dcdca3ebdc5e104fb8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For ARM platform, the bootblock may need more C source files to initialize
UART / SPI for loading romstage. To preventing making complex and implicit
dependency by using #include inside bootblock.c, we should add a new build class
"bootblock".
Also #ifdef __BOOT_BLOCK__ can be used to detect if the source is being compiled
for boot block.
For x86, the bootblock is limited to fewer assembly files so it's not using this
class. (Some files shared by x86 and arm in top level or lib are also changed
but nothing should be changed in x86 build process.)
Change-Id: Ia81bccc366d2082397d133d9245f7ecb33b8bc8b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2252
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This is a first cut at a romstage. It sets up memory, although that
needs some work; and finds and loads a ramstage.
Change-Id: I02a0eb48828500bf83c3c57d4bacb396e58bf9a5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2245
Tested-by: build bot (Jenkins)
This replaces the current stage-specific exit/entry functions with
generic versions. Now all stages compile with stage_entry(), which
is placed at .text.stage_entry.armv7, and stage_exit().
Snow's ramstage files are also updated to avoid build breakage.
Change-Id: I953a2c4b8121bd4b66c3362557997a9ca3aa53b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2254
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The SPI flash driver for Exynos chipset.
Verified to boot on snow/armv7.
Change-Id: I7eef67a9c57f825d09f13ea44c2b59b54345fa7b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2229
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The previous incarnation did not use all of mmu_setup, which meant
we did not carefully disable things before (possibly) changing them.
This code is tested and works, and it's a bit of a simplification.
Change-Id: I0560f9b8e25f31cd90e34304d6ec987fc5c87699
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2204
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This patch does a few things to get us into romstage:
- Add romstage as a stage (a later patch adds it as a binary, which
is probably wrong). The Makefile magic is complex enough that we
let it build the XIP file for now, but we no longer use it.
- Replace findstage with loadstage. Loadstage will find a stage,
load the code to memory, and zero the remaining part of memory.
Now we can link the romstage to go anywhere!
- Eliminate magic offsets from code/ldscripts and centralize Kconfig
variables in src/cpu/samsung/exynos5250/Kconfig.
- Tidy up code and serial output
Change-Id: Iae4d2f9e7f429cb1df15d49daf9a08b88d75d79d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2174
Tested-by: build bot (Jenkins)
This adds a wrapper around main() in romstage which is compiled using
-marm. This assumes that the bootblock branches to romstage in ARM
mode.
The long-term idea is to enforce ABI compatibility when handing off to
the next stage by using shims which are which are compiled in a pre-
determiend manner and leave the main portions of each stage up to
whatever the compiler wants. So it will eventually look like this:
1. bootblock_main (ARM/Thumb)
2. bootblock_exit (ARM)
3. romstage_entry (ARM)
4. romstage_main (ARM/Thumb)
(credit to Gabe Black for writing the patch, I'm just uploading it)
Change-Id: I4fdb8d2c6c2c0a7178bcb9154c378ddce0567309
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/2175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the bloated Snow bootblock which includes:
- SPI driver
- UART, including requisite I2C, Maxim PMIC, and clock config code.
- Adjustments for magic offsets (id section, stack pointer address)
This is just a temporary solution until we have romstage loading.
Once that happens, we'll rip out all but the code necessary for
copying SPI ROM content into SRAM.
Change-Id: I2a11e272eb9b6f626b5d9783eabb4a720a1d06be
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Our earlier attempt was jumping straight from asm to the old u-boot
board_init_f in lowlevel_init_c.c. We are getting ready to transition
to using a real bootblock for ARM, so add romstage.c to the files
compiled and we'll make main() our entry point.
This also updates romstage.ld to place main() (*(.text.startup)) at
the beginning of romstage.
Change-Id: Ifc77a6bfba27d915c4cad62c6c8040665294628a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2163
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't pass any arguments into romstage on ARM.
Change-Id: I018f28a57fc486c9240345cf0f4043b79027d864
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2162
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This replaces 0x02023400 with an SoC-specific Kconfig variable.
Change-Id: I21482d54a1e1fa6c4437c030ddae2b0bb3331551
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2130
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This mirrors the naming convention of handlers in
northbridge and southbridge.
Change-Id: I45d97c569991c955f0ae54ce909d8c267e9a5173
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2058
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This imports SPL (second phase loader) files from U-Boot. Most of the
content of these files will eventually go away since they're fairly
U-Boot specific. For now they are here to make Jenkins happy.
Change-Id: Ib3a365ecb9dc304b20f7c1c06665aad2c0c53e69
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2081
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Fix some minor discrepancies which prevented the MAX77676 from
getting compiled in properly.
Change-Id: Ib29136da6c15a4bdb24926a91729431c507cd209
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2076
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the minimal set of sources that allow the board to build.
These need to be filled in with actual code. But if we get these in upstream
we can stop working against a WIP patch.
Change-Id: I9347a573bb40761f6a12be3ee8febe3ca4be55a3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2018
Tested-by: build bot (Jenkins)
