CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Factor out some common expressions.
Add an error message when coreboots hangs waiting for a pstate
that never comes (it happened to me), and throw some
paranoia at it for good mesure.
If I understood BKDG fam10 CPUs never need a software initiated vid transition,
because the hardware knows what to do when you just request
a Pstate change if the cpu is properly configured. In fact
unifying a little what PVI and SVI do was better for my board (SVI).
So I drop transitionVid, which I didn't understand either (why
did it have a case for PVI if it is never called for PVI ?
Why did the PVI case distinguigh cpu or nb when PVI is
theoretically single voltage plane ? ).
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6401 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
actual SIO. This fixes the serial device being disabled during PNP
init.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6400 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Contemplate the possibility of nbCofVidUpdate not being
defined, trying to get closer to BKDG
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6399 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Configuration of F3x[84:80] was hardcoded for rev B.
I change that for some code that checks for revision
and configures according to BKDG. Unfinished but
hopefully better than it was.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6398 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
BKDG says nbSynPtrAdj may also be 6 sometimes.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6397 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I didn't understand quite why it did that iwth F3xA0 (Power
Control Misc Register) so I moved Pll Lock time to rules in defaults.h
and reimplemented F3xA0 programming. A later patch will remove
a part I don't know what's mean to do.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Bring F3xD4 (Clock/Power Control Register 0) more in line
with BKDG i more cases. It requires looking at the CPU package type
so I add a function for that (in the wrong place?) and some
new constants
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6395 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6393 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid. Factor out a little common code.
Also, our earlier config_clk_power_ctrl_reg0
was still too long and it'd get longer with forthcoming patches.
We now take apart F3xD4[PowerStepUp,PowerStepDown]
to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3x[84:80],
ACPI Power State Control Registers, to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6391 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xDC[NbsynPtrAdj],
Northbridge/core synchronization FIFO pointer adjust, to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xA0,
Power Control Misc Register to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xD4,
Clock Power/Timing Control 0 to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode). No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart VSRamp in step b
of 2.4.1.7 BKDG to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6384 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
A video option rom must be added for UMA graphics support. It can
be extracted from the supplied UEFI BIOS.
ASRock E350M1 support is based on the AMD persimmon project. The
major differences are SIO model and DIMM SDP addressing. With this
coreboot and seabios, the board can boot DOS from a SATA drive and
can boot WinPE from a USB flash drive. I was unable to get
Windows setup to run.
The board has a socketed SPI flash BIOS chip and a serial port
header. The SIO is Nuvoton NCT5572D. Using coreboot's existing
Winbond w83627hf is a good enough match to get the serial port
and keyboard working.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6382 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also it enables the FID/VID changes in SB. Jakllsch had some troubles with that too but on am2 CPU. Those bits are only documented in SB600. They arent in RRG RPR and BDG.
Signed-off-by: Rudolf Marek <r.marek@asssembler.cz>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This affects the CMOS options iommu, ECC_memory, max_mem_clock,
hw_scrubber, interleave_chip_selects.
If they're absent in cmos.layout, a Kconfig value is used if it exists,
or a hardcoded default otherwise.
[Patrick: I changed the ramstage CMOS handling a bit, and dropped the
reliance of hw_scrubber on ECC RAM, as it has nothing to do with it -
it's the cache that's being scrubbed here.]
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6380 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot used to set the chipset to IDE mode unconditionally.
Now, the user has a couple of ways to choose the configuration:
- If a CMOS variable sata_mode exist, it is used to decide if IDE or
AHCI is to be used as interface.
- If not, a Kconfig option is used.
- If unchanged, the Kconfig option is set to IDE.
So unless the cmos.layout is extended or Kconfig is modified, this won't
change behaviour.
[Patrick: Compared to Josef's version, I changed the Kconfig option to
be boolean, instead of a magic string. Also, the "IDE" default is
handled in Kconfig, instead of an additional line of code.]
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6379 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The southbridge already provides hard_reset.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6378 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Instead of enable the device the device gets disabled. However after some time the serial line gets back, most likely some "enable resources" might fix it.
I'm attaching patch which somewhat fixes the problem and changes the function to look same in all superio code. Some boards even did not convert the dev->enabled to 0,1 values.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6373 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It currently supports:
- Sleepbutton
- AC state
- Battery state
- Interrupt routing
- Display Brightness control
- Hotkeys
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The K8T800 is almost identical to the K8T800Pro, also added to this patch.
The K8T800_OLD is also defined, which is an older version of the K8T800,
but which has no driver and early HT code yet. Also extended the K8M890 VGA
driver to work for the K8M800 (not tested). According to the datasheet, the
K8T890 and K8T800 are similar enough to be able to use the same
initialization code. At least for the K8T800, this is sufficient to have
a working HT link with the CPU, and to initialise the V-Link to the
southbridge.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6367 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is incorrect, and will be replaced with proper ACPI for X60.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fixes abuild issues.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds support for Lenovo X60 series ThinkPads. So far, only X60s
(Model 1703) has been tested.
It's a basic patch without SMI and ACPI, as this makes it easier to
review. SMI and ACPI patches will follow.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Setting bit#21 in k8_f0#68 is part of the errata#169
which is handled in amdk8/coherent.c
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6354 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code provides support for IBASE Technology DB-FT1 (AMD code name Persimmon) and AMD Inagua platforms. It is dependent on all other patches in this set.
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6349 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code provides cpu early initialization for Family 14h cpus. It is dependent on the AMD Agesa code.
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6346 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code currently generates many warnings that are functionally benign. These are being addressed, but the wheels of bureaucracy turn slowly. This drop supports AMD cpu families 10h and 14h. Only Family 14h is used as an example in this set of patches. Other cpu families are supported by the infrastructure, but their specific support is not included herein. This patch is functionally independent of the other patches in this set.
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Everything else needs to be done by lpc.c Problem was that early settings survived, because the lpc.c is doing ORs only...
Hence we decode quite a lot and even strange ranges like IO port 0x4600 etc...
Also, if some port which does not fit to predefined set is requested, like 0x290 for Hardware monitor, the wide port is done, but in our case it has range 512 bytes which means we decode in fact 0x290 - 0x490. And if we hit GPU in the 0x3bx range I receive MCE exception if I do isadump -f 0x300 which is bad.
Therefore If I detect that the requested range is small (16 bytes) I additionally set the small wide io region so only 16 bytes is decoded.
While at it, I fix spelling typos and I init the regs so we don't write random garbage to regs even if we don't enable them later.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6343 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
execution from flash memory. Coreboot uses WB. While there is no
noticeable performance difference between the two settings, use
of WB can cause a problem for a jtag debugger. The attached
patch changes AMD cache as ram setting for flash execution from
WB to WP.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If enabled, set up 0xe0000000..0xf0000000 as MMCONF
area. Must still be configured in per-board ACPI for
the OS to pick it up, so it's disabled by default.
Signed-off-by: Josef Kellermann<seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6341 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Workaround for 131 removed.
Changed workaround for erratum 110 to only include pre-revision-F
processors.
For details, check AMD publications:
#25759 (Errata for Fam F pre-revision F processors)
#33610 (Errata for Fam F revision F and later processor)
Based on work and previous patches by:
Rudolf Marek <r.marek@assembler.cz>
Josef Kellermann <seppk@arcor.de>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6340 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a bit later.
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6339 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Corrects "index 98 has no mask" error at runtime.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6336 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reliability is accomplished by checking out the desired SeaBIOS commitish
into a branch named 'coreboot' in the local SeaBIOS git repository. Using
a branch allows TAG-$(CONFIG_SEABIOS_..) to refer to any commitish in the
SeaBIOS git repo, not just branches and tags.
Configuration is done with make defconfig followed by enabling and
disabling of the relevant coreboot-specific SeaBIOS options by appending
to .config using echo. This works, because later entries in .config will
overwrite earlier ones.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds support for the NSC PC87392 Super I/O. It is used in Lenovo
Docking Stations as Super I/O chip.
v2 because of:
- skip some empty files
- missing newlines in Kconfig and Makefile.inc
- add the Kconfig option in sorted order
Thanks to idwer on irc for pointing that out.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6333 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch adds support for NSC PC87382 Super I/O. It is used in many
Lenovo Notebooks as Docking LPC Switch.
v2 because of:
- Skip some empty files
- Fix newlines in Kconfig and Makefile.inc
- chip.h missed uart8250.h include
- add the Kconfig option in sorted order
Thanks to idwer on irc for pointing that out.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some RS690 devices require subvendor/subdevice IDs to
be programmed at locations other than default 0x2c.
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6330 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is so that boards can determine them on runtime based on hardware
properties, if so desired.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Kellermann <Joseph.Kellermann@heitec.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6329 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6326 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Lenovo PMH7 (Power Management Hardware Hub) is found in
most recent (starting with X60/T60 AFAIK) Lenovo/IBM Laptops.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6325 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a rare condition arises.
Based on findings by Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6323 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6322 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
VGABIOS, Intel MBI and the bootsplash image were added with special
build rules. These are replaced by generic cbfs-files-y entries now.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6320 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is in reponse to feedback that the original setup was too complicated.
New cbfs-files-y behaviour:
cbfs-files-y contains the names of files as they appear in CBFS. The
arguments describe the on-filesystem name, the type and (optionally) the
position. Example:
cbfs-files-y += foo
foo-file := bar
foo-type := splashscreen
foo-position := 0xffff8000
This configures a CBFS file called "foo" that is marked "splashscreen",
located at 0xffff8000 in flash and contains the data of the file "bar"
in the filesystem (either in the current directory, ie. where the
corresponding Makefile.inc resides, or if that doesn't exist, relative
to the toplevel directory).
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6319 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence we decode quite a lot and even strange ranges like IO port 0x4600 etc...
Also, if some port which does not fit to predefined set is requested, like 0x290 for Hardware monitor, the wide port is done, but in our case it has range 512 bytes which means we decode in fact 0x290 - 0x490. And if we hit GPU in the 0x3bx range I receive MCE exception if I do isadump -f 0x300 which is bad.
Therefore If I detect that the requested range is small (16 bytes) I additionally set the small wide io region so only 16 bytes is decoded.
While at it, I fix spelling typos and I init the regs so we don't write random garbage to regs even if we don't enable them later.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6316 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- actually hook up usbdebug in printk/print_ for romstage
- make usbdebug.c more similar to the Linux kernel version it was
originally derived from.
- increase retries and timing for usbdebug init (at least one chipset
seems to need this)
- src/pc80/usbdebug_serial.c is not needed
- some small console cleanups
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6315 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
because that is what it does.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6311 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds a new src/ec subdir for embedded controllers (mostly found in laptops)
and converts Getac P470 and Roda RK886EX to use the new ACPI EC instead
of having their own copies of those functions.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6304 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smm-y wasn't required before, because udelay.c used to be #included from
various files in src/mainboard.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6303 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPT port. With the CMOS variable set, LPT is found by SeaBIOS,
with the variable reset, it's not.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As Rudolf called.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6300 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the board. I thought we did this ages ago.
Also push CAR BASE further down so it won't conflict with a 32mbit flash part.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The AcpiPmaCntBlk have to be set.
Further research is needed to find out why.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6293 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6291 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6290 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6289 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note:
1. bimini_fam10/Kconfig: Set GENERATE_MP_TABLE in Kconfig. This will make sure the
smp_write_config_table will run. Then intr_data will be written
into 0xC00/0xC01.
2. bootblock: Use PCI_DEV(0, 0x14, 3) instead of
pci_locate_device(PCI_ID(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB800_LPC), 0).
The pci_locate_device will cause the system crash.
3. fadt.c: Change fadt revision to 1. 3 will cause the linux hang. Why?
4. early_setup.c: pmio 0x65 has change its meaning.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6288 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board is 2MB and the entry point is somewhere in the middle. quite weird setup
http://www.embeddedarm.com/products/board-detail.php?product=TS-5300
We should probably wipe the board from the tree. It will not work anyways with
current coreboot and the architecture is kind of obscure.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6287 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
After this patch, tilapia can run in higher memory frequency.
To test the high frequency, dont forget to change the freq limit in
mcti_d.c:
static void mctGet_MaxLoadFreq(struct DCTStatStruc *pDCTstat)
{
pDCTstat->PresetmaxFreq = 800;
}
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
have this go away again.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Kevin O'Connor <kevin@koconnor.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cache that range instead of the first 1Meg. This reduces boot time by
about 1 second on epia-cn.
This patch also adds a MTRRphysMaskValid bit definition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6272 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
defined if VGA_ROM_RUN is off. Define a dummy implementation of that
function for this case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6271 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6269 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to CBFS and adapt coreboot to use it.
Comments by Stefan and Mathias taken into account (except for
the build time failure if the table is missing when it should
exist and the "memory leak" in build_opt_tbl)
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6268 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
done. Please send the testing report.
Note: The pDCTstat->PresetmaxFreq in mctGet_MaxLoadFreq() should be set
to a higher limit, otherwise the frequnce will be set as 400MHz.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6258 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6257 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6256 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that feature is not ROMCC compatible.
Fixes build errors introduced in r6253.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6255 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on what the GPIOs are used for.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6254 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If a file "cmos.default", type "cmos default"(0xaa) is in CBFS,
a wrong checksum leads to coreboot rewriting the first 128 bytes
(except for clock data) with the data in cmos.default, then
reboots the system so every component of coreboot works with the
same set of values.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
select the right output device.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6252 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some of them do weird things to the option rom region (mapping
registers there or so) which failed as we handled these memory
region in emulation. As they were copied back to real memory
after the emulation was done, we can just as well use real
memory directly for these regions.
This affects IVT, BDA, and option ROM space.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6251 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by using 'Int32FromChar' macro, instead of the ASCII code.
Signed-off-by: Kerry She <kerry.she@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6248 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Correct default ROM image size for this board (512KB is correct).
- devicetree.cb: Add AUX I/O config (mainly GPIO settings).
This allows you to control the LEDs in the front panel and JP900/JP901
can be read.
- irq_tables.c: Rework PIRQ table to make more onboard devices work.
Also, avoid IRQ9.
- mainboard.c: Drop unneeded functions, everything is done in devicetree.cb.
Signed-off-by: Marc Bertens <mbertens@xs4all.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6247 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add missed CIMx file to romstage. in order to link them into romstage, move all CIMx table to .rodata section.
Run dos2unix on Makefile.inc, which is not upstream CIMx code
Signed-off-by: Kerry She <kerry.she@amd.com>
Acked-by: Kerry She <kerry.she@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6239 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We did the same with other chipsets in r6150.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6236 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move CACHE_AS_RAM_ADDRESS_DEBUG #define to Kconfig, where it was renamed
to HAVE_DEBUG_CAR in r5898.
- Move QRANK_DIMM_SUPPORT to Kconfig, see r6028.
- Drop obsolete/unused COMPRESS, see r6145.
- Drop obsolete SET_NB_CFG_54, see r6086.
- Move SET_FIDVID/SET_FIDVID_CORE_RANGE to Kconfig, see r6077.
Actually, the default for SET_FIDVID_CORE_RANGE is 0, so drop it.
- Rename some GENERATE_* options to HAVE_*, see r6027.
- Drop "select CACHE_AS_RAM", this is now set in the socket, see r6151.
- Drop ACPI_SSDTX_NUM, the global default is 0 already.
- Random whitespace and coding style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6233 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6231 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6230 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The main CIMx code is in a src/vendorcode directory and should not be
changed with regard to coding style etc. in order to remain easily syncable
with the "upstream" AMD code.
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6229 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add choice to use stable or master version of seabios repository
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6223 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to FG (FooGlue). As the GX2 has no VIP port.
-Change the Memmory setup MSR register names so they correspond better to the
databook. (Part1)
This is less confusing for beginners.
-Add a MSR printing function to northbridge.c like in the Geode LX code.
-Remove the AES register names.(GX2 has no AES registers)
-Delete some unused code.
-Clean up GX2 northbridge code to match Geode LX code.
-Add missing copyright header to northbridge.c.
-Move hardcoded IRQ defining from northbridge.c to irq_tables.c .
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
-Remove some white spaces.
-Remove some leading zeros.
-Fix a typo in LX code.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6219 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and drop some romcc relics in 440bx code too
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most boards unconditionally call this. Fix it in header file instead of each single romstage.c
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6216 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The intel/xe7501devkit is still broken, I think the (romcc) image is too big to
fit in the bootblock if CONFIG_DEBUG_RAM_SETUP is enabled. It would make sense
to convert all CPU_INTEL_SOCKET_MPGA604 to CAR, but I have no hardware to test.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
allocator. If that does not work out, they should be set in the code. Setting
them in Kconfig is the worst possible thing to do.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6213 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- nokia/ip530/devicetree.cb, southbridge/ti/pci1x2x/pci1x2x.c:
- Fix SMSC FDC37B787 name (was a typo).
- Disable PS/2 keyboard/mouse LDN, the IP530 doesn't have either.
- Fix typo: s/PCI_DEVICE_ID_TI_1420/PCI_DEVICE_ID_TI_1520/.
- All of these are confirmed by Marc Bertens on IRC.
- Fix a few CHIP_NAME HP board names.
- Random whitespace and coding-style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6212 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6211 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6210 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed for all Intel 440BX boards with 4 DIMM slots (such as this one).
Thanks Marc Bertens <mbertens@xs4all.nl> for bringing up the issue and
for the success report for this fix on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6207 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's a good thing to use printk() instead of print_*() anyway
on 440BX (and other chipsets which have been converted to CAR).
Build tested and boot-tested on ASUS P2B-LS.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6206 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Simple devicetree.cb fix, tested on hardware using a PCI-E x16 graphics card.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6203 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6202 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Don't include cmc.bin to the build. It's required, but we don't ship it
- mptable's API changes a bit. Adapt.
- Fix ACPI for new iasl versions with improved code validation
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6199 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which uses it.
Compiles, but not boot tested lately.
Many things missing (eg. SMM support, proper ACPI, ...)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Mostly done according to initial file creator.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6192 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move some variables where they belong
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6186 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We currently use "COREBOOT" unconditionally as the "OEM ID" in our
mptable.c files, and hardcode the mainboard name in mptable.c like this:
mptable_init(mc, "DK8-HTX ", LAPIC_ADDR);
However, the spec says
"OEM ID: A string that identifies the manufacturer of the system hardware."
(Table 4-2, page 42)
so "COREBOOT" doesn't match the spec, we should use the hardware vendor name.
Thus, use CONFIG_MAINBOARD_VENDOR which we have already as the "OEM ID"
(truncate/fill it to 8 characters as per spec).
Also, use CONFIG_MAINBOARD_PART_NUMBER (the board name) as "product ID",
and truncate/fill it to 12 characters as per spec, if needed.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
That variable allows chipset components to add files to
the CBFS image, for details see
http://www.coreboot.org/pipermail/coreboot/2010-December/062483.html
Compared to the patch in that mail this commit improves dependency
tracking a bit.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6182 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the current hda_verb.h files are identical (same MD5 sum) and are
intended for a specific MCP55 board with the Realtek ALC880 audio codec,
which has the vendor/device ID of 0x10ec0880. They were splitted out from the
MCP55 southbridge code and put into board dirs a long time ago (which is
correct, as those settings are indeed board-specific), but they were never
adapted to those boards.
Here's the table of which codec is soldered onto which board, based on
checking the vendor website board spec pages, and the board manuals:
- GIGABYTE GA-M57SLI-S4: Realtek ALC883
- MSI MS-7260: Realtek ALC883
- MSI MS-9652: Realtek ALC888
- MSI MS-9282: Server board, doesn't have audio at all
- Tyan S2912: Server board, doesn't have audio at all
- All Supermicro boards: Server boards, don't have audio at all
- NVIDIA l1_2pvv: No public info to be found, but I assume this was the
original MCP55 eval board for the port and it's probably has the Realtek
ALC880 codec used in the original hda_verb.h.
These are the codec vendor device/IDs involved:
Realtek ALC880: 0x10ec0880
Realtek ALC883: 0x10ec0883
Realtek ALC888: 0x10ec0888
The following files are marked as incorrect / TODO, as the ID of the codec
doesn't match and thus will never get actually used (you'll see
"HDA: no verb!" or similar in the coreboot logs). Even if the ID matched,
the rest of the table would be incorrect anyway because the values are
highly board-specific.
./src/mainboard/gigabyte/m57sli/hda_verb.h
./src/mainboard/msi/ms9652_fam10/hda_verb.h
./src/mainboard/msi/ms9282/hda_verb.h
The following files can be safely dropped as these are server boards and
don't have HD audio (or other audio) at all:
./src/mainboard/supermicro/h8dmr/hda_verb.h
./src/mainboard/supermicro/h8qme_fam10/hda_verb.h
./src/mainboard/supermicro/h8dme/hda_verb.h
./src/mainboard/supermicro/h8dmr_fam10/hda_verb.h
./src/mainboard/tyan/s2912/hda_verb.h
./src/mainboard/tyan/s2912_fam10/hda_verb.h
The following two are correct and can stay:
./src/mainboard/nvidia/l1_2pvv/hda_verb.h
./src/mainboard/getac/p470/hda_verb.h
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6180 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch looks at certain DDR configurations (dual rank/single rank) and lowers the clocks to 2T or frequency as guide suggest. It sets the DualDIMMen bit which I believe should be set for non-dual channel configs.
The patch does not implement support for three dimm configurations supported from revE.
On the other hand it should improve greatly memory stability across the 939 platform.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6176 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6175 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and do that only if resume is done.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The writes to NVRAM are not used in asrock board (k8 pre rev f) but they should work when used with am2 boards. In fact maybe the suspend will work on mahogany or others ;) - with some simple patch which follows for asrock.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6173 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
The patch is based on my 2008 patch.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6172 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested. Please check all changes if I did not make any wrong while converting this to bytes.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6171 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is an AMD K8 + NVIDIA MCP55 + ITE IT8716F mainboard.
It has a working hda_verb.h file for HD audio, and a fanctl.c file is
used to enable the CPU fan (among others) so that we don't kill the
CPU due to excessive heat.
Even though some TODOs remain of course, it works good enough to
successfully boot Linux (e.g. via SeaBIOS).
The full status report is available at:
http://www.coreboot.org/ASUS_M2N-E
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6170 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
[PATCH] SB700 common FADT was not applied to this board because it was in the meanwhile added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6167 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Factor out the ROM decode enable functionality into bootblock.c and
handle it via the usual TINY_BOOTBLOCK mechanism.
Use "select TINY_BOOTBLOCK" in the southbridge, not individual boards.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6159 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All southbridges using TINY_BOOTBLOCK have a bootblock.c files which
simply includes an enable_rom.c files. As discussed on the mailing
list, drop the enable_rom.c file by merging it into bootblock.c.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6158 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The files debug.asl, globutil.asl, and statdef.asl are duplicated in
many K8/Fam10h boards. However, they're neither board-specific nor
K8/Fam10h-specific nor AMD-specific, so move them to src/arch/i386/acpi.
debug.asl contains generic chunks for I/O port 0x80 handling, and debug
output over serial port (init COM port, send byte, send string, etc).
globutil.asl contains utility methods for string comparison, string length
and similar stuff.
statdef.asl contains generic ACPI bit definitions / status codes from
the ACPI spec (not board- or chipset-specific).
This patch was mostly generated by:
mkdir src/arch/i386/acpi
svn add src/arch/i386/acpi
svn cp src/mainboard/amd/dbm690t/acpi/debug.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/globutil.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/statdef.asl src/arch/i386/acpi/
cd src/mainboard
find . -name debug.asl -exec svn rm {} \;
find . -name globutil.asl -exec svn rm {} \;
find . -name statdef.asl -exec svn rm {} \;
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6156 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Definitively a iasl problem, it can't even disassemble it's own
> output back to something equivalent to the input file.
> It seems to be generating Bytecode for the Add where it shouldn't.
Here is a solution using the SSDT.
Unfortunately iasl does not resolve simple arithmetic at compile
time, so we can not use Add(DEFAULT_PMBASE, PCNTRL) in the
Processor statement.
This patch instead dynamically generates the processor statement.
I can't use the speedstep generate_cpu_entries() directly since the
cpu doesn't support speedstep.
For now the code is in the southbridge directory, but maybe it
should go into cpu/intel/ somewhere.
IIRC notebook cpus of the era can already have speedstep, so it
would probably be possible to pair the i82371eb with a
speedstep-capable cpu...
Also, I don't know if multiprocessor boards (abit bp6?) would need
to be handled differently.
Abuild-tested.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All K8/Fam10h boards use CAR, so move the "select CACHE_AS_RAM"
into the socket directories, and remove it from the individual boards.
Do the same for Intel CPUs/sockets where all boards use CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6149 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use w83627hf_set_clksel_48() where needed instead or open-coding the same
functionality, and also use w83627hf_enable_serial() instead of
w83627hf_enable_dev() (which does exactly the same, but isn't wrapped in the
enter/exit config mode functions).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6143 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
De-asserts STRAP_BIF_all_valid for
PCIE-GFX core.
After lane reversal,
Asserts STRAP_BIF_all_valid for
PCIE-GFX core.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: QingPei Wang <wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6142 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The read-modify-write wasn't needed. This is easier to understand.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6135 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Single channel (in slot DDR1 and DDR3) produces strange artefacts on screen (and hang)
Dual Channel (in DDR1 and DDR2 aka blue slot) - works nice
All slots populated - same case as Single channel - must be something wrong with UMA.
Tested with 2x 512MB CAS 2.5 DDR400
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Stefan Reinauer wrote:
> > The specified IO port is most likely wrong. As the comment mentions, the
> > SSDT is a good place for that. A preprocessor define used both in the
> > CPU init code and in the asl would solve the problem without an SSDT.
> > For some info on CPU SSDT creation on intel check out
> > src/cpu/intel/speedstep/acpi.c
>
> The IO port is ok (and I wrote the comment myself ;)):
> DEFAULT_PMBASE is 0xe400
> PCNTRL reg offset is 0x10
>
> Using the preprocessor will probably work too if iasl can do simple
> arithmetic (likely yes), I'll look into that.
BTW, my first idea was to use an acpi method that looks up pmbase in
the pci cfg space, but when I define a method like this:
Method(TEST, 2)
{
Return (Add(Arg0, Arg1))
}
I get:
|build/mainboard/asus/p2b/dsdt.ramstage.asl 9: Processor (CPU0,
|0x01, TEST(0xe400, 0x10), 0x06) {}
|Error 4096 - syntax error, unexpected PARSEOP_NAMESEG,
|expecting ')' ^
While using the builtin Add() directly works.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I cleaned up the patch and moved most of the dsdt.dsl and
acpi_tables.c into the southbrige/northbridge directory.
Updated patch should fix abuild error and incorporates suggestions
on irc by uwe (thanks for the comments).
Thanks to Idwer Vollering <vidwer@gmail.com> for the original patch.
Tested:
Linux (poweroff, powerbutton event)
XP (poweroff, powerbutton event)
Abuild-tested
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In bcm5785_enable_rom(): Use PCI IDs from pci_ids.h instead of hardcoding,
and use 'dev' instead of 'addr' as device_t variable name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6125 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add missing license header to amd8111_enable_rom.c, add some more code
comments and use PCI IDs from pci_ids.h instead of hardcoding.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6124 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move CONFIG_HT_CHAIN_END_UNITID_BASE #ifdef block to mcp55.h to make
the build work (but this is a good idea anyway, as it's used in
multiple files).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6123 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the board-specific parts for S3 support on the M2V board.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6122 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initialized properly because the pcie link takes some time to come
up.
I set the timeout rather arbitrary to 100ms, this is what a BIOS_ERR
and higher only boot looks like on my system (with pcie printks set
to BIOS_ERR so they show up):
|Device error
|Device error
|PCI: 00:02.0 PCIe link up after 35800 us
|PCI: 00:03.0 PCIe link up after 12900 us
|PCI: 00:03.1 PCIe link timeout
|PCI: 00:03.2 PCIe link up after 32000 us
|APIC: 00 missing read_resources
|I2C: 01:50 missing read_resources
|I2C: 01:51 missing read_resources
|I2C: 01:52 missing read_resources
|I2C: 01:53 missing read_resources
|Start bios (version pre-0.6.2-20101025_023503-nukunuku)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6121 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD RS780 uma graphics. Tested with frame buffer sizes 64m through 1GB
by running dxdiag and Windows media player at 1600x1200 true color.
Additional changes needed to boot Win7 on Mahogany_fam10 will follow.
-- Enable and program the debug bar as required by the ATI graphics driver.
First, make the debug bar writable and allow resource allocation code
to program it. Once programmed, enable its operation.
-- Disable the family 10h processor mmconf while the RS780 mmconf is in use.
-- Make strap programming more closely follow the reference BIOS.
-- Disable PCIe bar 3 after using it.
-- UMA size is no longer hardcoded.
-- Disable write combining for all steppings to eliminate stability problem.
-- Correct task file data.
-- Improve the accuracy of the Atom table that passes information to the driver.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6120 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
using it directly again.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should probably be C code in some .c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Mention full name of all the tables (SSDT, FADT, etc).
- Drop obsolete / incorrect "LXBIOS" reference.
- Add missing ACPI address space type #defines specified in newer versions:
ACPI_ADDRESS_SPACE_EC, ACPI_ADDRESS_SPACE_SMBUS.
- Add missing "enum acpi_apic_types" entries: Localx2Apic, Localx2ApicNMI.
- Add ACPI_FACS_64BIT_WAKE_F #define.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
default on all boards) into Kconfig.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6109 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not brought over to Kconfig (this applies to all #defines to 4, as
that's the default anyway)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Except for one instance the spd_addr.h were now very tiny, there's not
much point in keeping that stuff in an extra file. The only user of those
files is the romstage.c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, coding style, and indentation in some places.
- Add comments for less obvious entries and hardcoded numbers (e.g. 'type').
- Add comments for all/most 'revision' fields, mention in which version
of the ACPI spec which revision number is to be used.
- Add URLs to a few external documents which describe tables that are
not mentioned in the ACPI spec (or where the external document may
provide further info), e.g. SRAT, SLIT, HPET, MCFG, etc.
- Use the ASLC #define instead of hardcoding "CORE" in one instance
(ASLC is already used everywhere else).
- Add some TODOs for additional stuff which is in the spec but not yet
handled by our code / #defines.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset code (where it belongs)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Xavi Drudis Ferran