This was used as a means to read the MAC address and dynamically
return it to the ethernet driver via ACPI. The kernel team ended
up going another direction so this became obsolete.
Change-Id: I7065bea4b288c689b41cc969989ec6fd87c75f1f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49902
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
USB2 ports assigned to type-C connector need to be configured properly
by the USB2_PORT_TYPE_C. and also modify the description of USB port.
BUG=b:177480902
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot chromeos-bootimage
build Pass
And check the typeC port function is normal by manual.
Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com>
Change-Id: I9e962f8cd76e1986700821168594c50bc21553e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50217
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI entries for AT24 NVM device.
BUG=b:169551066
TEST=Build and run for basic camera functions.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ib8fb684166649f78713050d62445bf47189b06ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jim Lai <jim.lai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Define the 25th bit of the fw_config for the regular touchpad
and numpad touchpad selection.
BUG=b:174027837
BRANCH=firmware-volteer-13672.B
TEST=build pass
Change-Id: Ic5d61f19fd385600cfdcdd045dab1e61b06e4663
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add the TBT PCIE rp setting to on and also fixes system hang
in recovery screen after selected "Power off" item problem.
BUG=b:177963941
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot chromeos-bootimage
build Pass
And check the system can power off normally in recovery page
Cq-Depend: chrome-internal:3581043
Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com>
Change-Id: Ic0a4756b4af839ea0a23febb991bd71af7733dcc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50103
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Ariel Chang <ariel_chang@pegatron.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It is the same for all three mainboards.
Change-Id: Ic5786bcc29e2549d6fc935d60c699c1cab84b237
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50027
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per Hardware Architecture Specification (HAS) ADL-P has 7 CLKSRC
and 10 CLKREQ (7 SRCCLK is internal and 3 SRCCLK from external CLK chip).
ADL-M has 6 SRCCLK and CLKREQ (no external CLK chip).
Change-Id: I7d223c165f819669722cbc80245fa8ec20372352
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50130
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Acoustic noise mitigation for magolor and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:178678267
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: Idea2a801399bb5c7e0b8e59ee7a826c86a44f4ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50099
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initiate peripheral buses based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ibf48aceca7ac8774b0353e31bd81e1880c4066ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change moves the selection of SOC_INTEL_CSE_LITE_SKU into Kconfig
under BOARD_GOOGLE_BASEBOARD_VOLTEER instead of requiring each
individual board to select it.
TEST=Verified that timeless build does not result in any changes.
Change-Id: I2d94931fdc3077794bed5cc51708b5a5d9e64972
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This variant never really got used and can be deprecated.
Change-Id: I5d59460c90266ba5f9c3bdb951f53a37ffae9e03
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
A new schematic revision indicates that the old wake pin is not used,
and brya will only use 1 IRQ pin from EC, routed to GPP_F17
BUG=b:178605367
TEST=Build test
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ia2bc5b1562ab30b4461fc7e3b1a4bc3e370db588
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit f41645c34d.
In Dragonair, during the MP stage, one of the resistors needed
for this functionality has been removed. This results in the
privacy-switch not readable back by the system.
BUG=b:178458332
Change-Id: I0781f338d5ecd89fccee613fb13ea25c59385625
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1. These are common OCP/Facebook IPMI OEM commands, move from mainboard
into drivers/ipmi/ocp to avoid code duplication and provide better
reusability.
2. OCP Tioga Pass enables IPMI_OCP driver.
Tested=On OCP Delta Lake and Tioga Pass verify the commands still work
correctly.
Change-Id: Idd116a89239273fd5cc7b06c7768146085a3ed69
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Select SOUTHBRIDGE_INTEL_COMMON_ACPI_MADT and drop the `acpi_fill_madt`
function definition, which is redundant. Tested, still boots to payload.
Change-Id: I6ba448f264a478e7ef060ea1dfbf5016a310d528
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Also refactor the machine type checks to avoid code duplication.
Tested, still boots to payload with 256, 128 and 64 busses.
Change-Id: Ib394ba605bbfeee75aa645e989c23034cceff348
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50025
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move all Q35 register definitions into the q35.h header. Note that real
hardware does not have EXT_TSEG_MBYTES, because it is QEMU-specific.
Change-Id: I4c86ac0bb05563dee111b9b4a4a71c1c31198acd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50024
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only specify the type of MMCONF_BASE_ADDRESS and MMCONF_BUS_NUMBER once.
Change-Id: Iacd2ed0dae5f1fb6b309124da53b3fa0eef32693
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We want to add some function declarations as static_testable to this
header but including it in a .c file outside of tests will yield a gcc
warning like:
error: 'function' declared 'static' but never defined
[-Werror=unused-function]
It seems these includes aren't necessary anyways so we just remove
them.
Change-Id: I17147136579140b94728ceb1c369b1348714bc53
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
We started depending on dsdt_top.asl in dsdt.asl but this newly added
board wasn't adapted yet, so have it catch up.
Change-Id: If00280a33fd9e5c3ef1b3d07c41e81ed18013714
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50021
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
lint-001-no-global-config-in-romstage error on
D0F0_PCIEXBAR_LO.
DOF0_PCIEXBAR_LO is defined in bootblock.c and
romstage.c.
Place D0F0_PCIEXBAR_XX in local gm35.h.
BUG = N/A
TEST = Build and boot QEMU x86 q35/ich9
Change-Id: Ia5ac9eb797de996186282193647313b9f7b42624
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Add wifi sar for galith
Using convertible mode of fw config to decide to load custom wifi sar or not.
BUG=b:176206495
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Cq-Depend: chromium:2649378,chrome-internal:3559387
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I0f9a7ddedef550317da4bf798317619ffd1fa979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Raise little CPU to 2GHz at romstage to improve boot time.
BUG=b:177389446
TEST=observe boot time by `cbmem`
Before: 1,062,359 us
After: 907,458 us
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I723a916d7f708627525ef11e3c5ea0b381f269aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Configuring GPP_G7 as NC causes SD card detection issue on sasuke.
So we'd like to remove the GPP_G7 override and keep the baseboard
configuration as native function (SDIO_WP).
BUG=b:175831709
BRANCH=firmware-dedede-13606.B
TEST=Built and verified SDR104 SD card operation on sasuke
Change-Id: If73337b482f04fd263caaa6fed0e54aa87bd876e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Except for one debug print in sarien, both functions are identical.
Move them to driver code to avoid unnecessary redundancy.
Change-Id: I82635a289e3c05119eab4ee1f7a6bf3a8a1725c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add the GL9755 support to drobit and also fixes the S0ix can't into C3~C9 problem
BUG=b:174348200
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wayne3_Wang <Wayne3_Wang@pegatron.corp-partner.google.com>
Change-Id: I52df6b2cdebfaf8a5eb010c4af1a2cf3d918f5e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49921
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Paul2 Huang <paul2_huang@pegatron.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Added device hid info to the MST RTD2141b device on
trembyle.
BRANCH=zork
BUG=b:147402710
TEST=Build and flash BIOS image, see 10EC2141 appears
under /sys/bus/i2c/devices
Signed-off-by: Shiyu Sun <sshiyu@chromium.org>
Change-Id: I97a67f9dbc31cd788d579252d7d355b24d97ca30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- Both NVMe ports
- SATA port
- All USB ports
- Webcam
- Ethernet
- Integrated graphics
- Internal microphone
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux and Windows
Not working:
- Discrete/Hybrid graphics
- Internal speakers
These two require new drivers to work correctly, which will be added and
enabled later.
Change-Id: Iae6e530dcd52df3642cdfe74b65bfff5aa0dd402
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
With top-aligned bootblock this is no longer globally needed.
The default maximum is now a generous 256 KiB with couple
platforms having lower limits of 32 KiB and 64 KiB.
Change-Id: Ib1aee44908c0dcbc17978d3ee53bd05a6200410c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This reverts commit 2a1638a9ce.
The original commit broke Mandolin and with the revert applied, I can
boot into Linux via SeaBIOS again.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7024b6ff1e772bbc89f810c766655a5887ed8b41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49950
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds mem_list_variant.txt that contains the only
memory parts used by brya0 for Proto-0 build and Makefile.inc
generated by gen_part_id.go using mem_list_variant.txt.
BUG=b:176491791
Change-Id: I3fe755564e7541a7abdfca0e5aa7fd786f5ca880
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Use the same variable name as soc/intel to implement a common
_PIC method at top-level ASL.
Change-Id: I48f9e224d6d0101c2101be99cd18ff382738f0dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
K4U6E3S4AA-MGCR
BUG=None
TEST=Build the sasukette board.
Change-Id: I57c9d22ae655032120f19add98ef454853428af5
Signed-off-by: chenzanxi <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Remove typedef device_nvs_t and move struct device_nvs
outside of global_nvs. Also remove padding and the reserve
for chromeos_acpi_t.
Change-Id: I878746b1f0f9152a27dc58e373d58115e2dff22c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Per Facebook BIOS requirements 'Locator' field should not
have any space between words.
Tested=On OCP Delta Lake, dmidecode -t 17 to verify.
Change-Id: I2f6f1b2590c55d6da4ca32aef2f50eb332f441dc
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add camera ACPI configuration for Voema
BUG=b:169551066
TEST=Build and boot Voema. Start camera app and able to
capture images.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I903e5e0b5f85718c7c9cbb6d5cafb8fc9ad5814e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jim Lai <jim.lai@intel.com>
Set the supported C-State to C1 and C6. This matches the states in
CPUID(5).
Change-Id: If32b8256097b5b2bee7fb074fab105e4b54d14b3
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49803
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do not pass ACPI S3 state as a parameter, by locally
calling acpi_is_wakeup_s3() compiler has better chance
for optimizing HAVE_ACPI_RESUME=n case.
Test for acpi_s3_allowed() is already included in the
implementation of acpi_is_wakeup_s3() and is removed
as redunandant.
For ramstage, acpi_is_wakeup_s3() evaluates to
romstage_handoff_if_resume().
Change-Id: I6c1e00ec3d5be9a47b9d911c73965bc0c2b17624
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49838
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For board version 6 afterward, it will have external pull-up for
GPP_C12, and remove internal pull-up.
BUG=b:177618684
TEST=emerge-dedede coreboot, check evtest if SW_PEN_INSERTED event
(value:1/0) when insert/eject pen, and eject pen to wake system from s0ix
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I503873afb48384168dcd8a822c7246655898356e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
set pwron_varybl_to_blon to 0x5, which means fw will delay 20ms between backlight
on and vary backlight.
BUG=b:171269338
BRANCH=zork
TEST=Build; Verify the UPD was passed to system integrated table; measure
the power on sequence on dalboz
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I8af35eee7777a8e71b42f0c128795290b8c2c93e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
"usb2_ports[7]" for internal bluetooth device was configured as
'USB2_PORT_EMPTY' mistakenly in previous patch, so we need to enable
it again.
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=Built and verified BT device existence with lsusb
Change-Id: Id2900152e23bbc2f454d064dc86a9e45e934ea0f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds explicit initializations for the remaining named display
(power) control GPIOs to the bootblock GPIO init code. These pins are
usually mapped to pins that are already configured to pull-downs on
power-on reset so this wasn't really required, but we have already moved
them around so often that you never know when EEs might one day move
them to a pin with a different power-on reset configuration, so it's
better to be explicit.
In one particular case, GPIO(67) (used by CoachZ rev1+ but not by
anything else for the EN_PP3300_DX_EDP pin) is not actually a pull-down
on boot, even though that is claimed by the datasheet. This is likely
due to the fact that it can serve as the SPI_HOLD pin for the boot flash
QSPI bus, so even though our board's boot flash doesn't really use that
pin, it seems that the boot ROM still configures it as such.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I533baa962d2dfc87cfa510f442ed2e8912e0e5b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This conflicts with the MSTH i2c_tunnel.
BUG=b:175146875
BRANCH=zork
TEST=Boot trembyle and inspect ACPI tables.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iac04c7dc361d427f5ebb99644aa70bd0c7dbb918
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
It's easier to understand what these symbolic names mean rather than
using the constants; the static.c will will end up (indirectly)
including `soc/usb.h` therefore the macros are in scope here.
Change-Id: I5ef977a05a2522e177f32c99bfab74f9288ae869
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:173476380
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: Ib31c5d55e30b958d3e552e8d0b4a160947444636
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are:
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:165209698
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: I80afd6bf1257b9a72d0d7651b48d243ebaf5de2f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
The only difference is an additional include that is no longer needed.
Change-Id: I0053d03aa4d05f5c0fa833d8634419b6667e38a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49832
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to repeat the same code on every board.
Change-Id: I2e19decfe8609fa644e609673a56ee5109bafefa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49831
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses the newly added meminit block driver and updates TGL
SoC and mainboard code accordingly.
TEST=Verified that UPDs are configured correctly with and without this
change.
Change-Id: I6d58cd6568b7bbe03c4e3011b2301209893e85a9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
All Broadwell boards only use the `mainboard_pre_raminit` function to
call `mainboard_fill_pei_data` and optionally `mainboard_fill_spd_data`.
Move the declaration and weak definition of `mainboard_fill_spd_data` to
platform code, replace the call to `mainboard_pre_raminit` in romstage.c
with calls to `mainboard_fill_pei_data` and `mainboard_fill_spd_data`,
and delete all other instances of `mainboard_pre_raminit` for Broadwell.
Finally, delete now-empty romstage.c and spd.h files from mainboards.
Change-Id: I3334b20bd7138bb753b996a137ff106e87c6e8a5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Make it optional and change its signature.
Change-Id: I4b5f3fb08e8954514ebf39e72c95aa62d66856d7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This allows us to drop many now-redundant Kconfig options.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
The default configuration file also remains identical, as expected.
Change-Id: I20b0200550508679bf2533342ce918b221dcf81e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The VR config and S0ix options are now specified for the CPU chip.
Change-Id: I75e405d41b4a0605e786fe761c92535e62d0cfce
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46945
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code to read the SPD file and index it is not variant-specific.
Change-Id: Iaee0a77934a45c65bf32dd0dba23cec654abc0b9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
It is identical for all variants that have it.
Change-Id: Iec3a5f036d9b760d1075059f2db1480b1c76273e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
They are part of the same line, so merge them.
Change-Id: I969ce91f7a5f16a85750c140eaa444d7923b2014
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Factor out common DRAM SPD definitions and relocate SPD GPIO macros.
Also factor out common function definition. Drop now-empty headers.
Change-Id: Id05ba6c9cea27fbad5ee831f033d0de43717847e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib827e9b2919dbd0e16f30b8dfde46348365d9622
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The PMC doesn't response any more due to invalid CNVi GPIO
configuration. This caused a 30 second boot delay in FSP-S.
Use the same values as FSP-S does. Always disable external I2S BT
audio and use NF3 for pad GPP_D5 and GPP_D6.
Tested on Prodrive hermes:
No boot delay can be observed any more.
Change-Id: I6f4a954786ec21512b0dce908d333952e96de048
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49678
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is located below TOLUD. The size is configured in ESMRAMC but can
also be configured with "-global mch.extended-tseg-mbytes=5" command
line argument. Note that the size in ESMRAMC needs to be 'invalid' (3)
for this to take action.
coreboot will leave TSEG at the default 1MiB.
Note that even if TSEG does not end up being used, it is likely a good
idea to not put anything there as if SMM gets locked down by something
else it will suddenly be inaccessible.
Change-Id: I5fd82a42d6602f1369bb3c69556c46f537542705
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a bootblock gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: Iad40b6315a29e7aea612a3e1a169372d296d1d6c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49443
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I357099f797be178543a9e6637335cd0a68633071
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49441
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I8b30eb5d70c34ae3e2ed24ab52dd1357a54c5ae7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49439
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I0b956427a9cec56d06b03f7f05138f75137b4ea3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49437
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ibc727302109456eb1d86652c947ce85b3a64c5b2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I80369ab70d5510cb4f388f3029119e7148361af4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49435
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Id6b55d7f3d3fbfc5b55497708f24006614760d03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49434
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I130fd26944169430a84c3609432b1b5283581c99
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49432
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ie3878b47b8e20c51b928a38df9ccedf2d50d478e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49431
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib19a4f64eaf25bf2eb47ee60748a68538fc0729a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49430
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I279956f30cbb6fb031cdfe6aaa09b644b6b7d3e7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49427
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LPC/eSPI pad configuration is already done at board-level. Thus,
drop redundant configuration by dropping the call to lpc_configure_pads.
Change-Id: Ib9e62bf19e6f1fbe32a340e4802c13504a0d6def
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49417
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie1e53e72c65fdcfe4be2e01134873aa7858c28ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49416
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding one missing pad to the early gpio table and
dropping the call to the soc function.
The soc code gets dropped in CB:49410.
Change-Id: I210633d4520fcfab59f68268bd7991557433ce38
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49415
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: If0693a4419c58dde3c4536698940f03c30304b9d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49414
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding missing pads to the bootblock gpio table.
The soc code gets dropped in CB:49410.
Change-Id: I95993b1bd4f1fd8b4ac7b21fb89ec4d196b0240a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49412
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I62ffbe36bd7b7675aa0f41a8c6e9214d04ad4ae5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49428
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I6fedcebea3bb31d992bac1e3b21382fea93a8b82
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49429
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ieeb738afd54e77ee853ee109009f611411aa0d4a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49426
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5482f44b361925b7d2dbcbf1065c1be035c68b0b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49424
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I7dcf88d61c305f0598a0a79f8cfa46ef5009564b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie33bae481f430a1c4410a0a4e2b2a34a3e78adaa
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49411
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow MRC training in SA GV.
BUG=b:177779469
BRANCH=firmware-volteer-13672.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Idc9f634135b489450f53f8cd28d80649309d0f70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Assigned USB2 port to type-c use.
BUG=b:177483060
BRANCH=firmware-volteer-13672.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I9bd820406124927d56296508be05033217c0d472
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49638
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Increase DCACHE_RAM_SIZE to 32kB and remove "NO_CBFS_MCACHE".
It’s quite safe to increase DCACHE_RAM_SIZE. All LGA775 targets
should have at least 256K L2 cache. That is plenty for XIP RO cache of
bootblock + romstage and a 32K CAR.
Change-Id: I393b2727bd90a990c3108a4dbead62b17d7fc531
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Correct GPIO settings as below reason:
1. GPP_G7 not being used but set to NF.
2. GPP_C22 and GPP_C23 is set to NC but internal pull down to 20K
BUG=b:177283756
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage and boot into emmc
Change-Id: Idf25674efa2336bde98c5abaff278484fd71ea8b
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to NC
BUG=b:175932166
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage and boot into emmc
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id7780d5332551ed3fd20ef14f8b5d31164f16385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I795b8da3c5e1efb51c8fe4673f025839a1c630bc
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I2f484d232a46214ff98168f41f96d56b047892e2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I67bdd9a96928b77a9a178afea7dab03dc370312c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I342b9217af0288a3b525e629aac791eb0f880442
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Functionality depends of CMAP and CMBP references inside board
specific ASL implementation. Only roda/rk9 and roda/rk886ex has
that.
Change-Id: I4da8292375cb589d67dc68496b1e81971bc2a61f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49274
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Chrome EC dropped strago support, so we need to disable it here
before updating our Chrome EC submodule.
Change-Id: Ied8905e995fd040b981ce18e95e225ade496d23c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48216
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use the function smbios_mainboard_version()
to query the board revision from the EC.
we need to select GOOGLE_SMBIOS_MAINBOARD_VERSION.
BUG=b:177818769
TEST=1. emerge-volteer coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Change-Id: I2474ee03845356d0775f6da25274f696ad33f935
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SoC code has in implicit dependency on this option, so select it in
the SoC code instead of the mainboard code.
Change-Id: Iea908c142f4a94a107cf74a31d9f5e29668d4b5b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the sasukette variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:175848514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKETTE
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I0a554efe0919dc2f5880f0f7817a37bd4be88ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change enables LTE modem for sasuke.
- Add LTE modem device into devicetree
- Add GPIO control for LTE modem power on and off
BUG=177177967
TEST=Built and verified modem device existence with lsusb
Change-Id: I34ba8ab00b73f24d1786ab014e9981b172a63a27
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49163
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DPTF paramerters from thermal team.
1. PL1 max =5.8W
2. PL1 min =3.8W
3. PL2 =20W
BUG=b:177249297
BRANCH=dedede
TEST=build image and verified by thermal team.
Change-Id: I19654b65613817ebecf979ce7ac4f76d370ebdc2
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested=On OCP Delta Lake, verify the VPD values can be read
correctly.
Change-Id: I1c27cb61cd52902c92b3733e53bc8e6fd6a5fe7f
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is claimed getac/p470 has this implemented and not
as a TODO.
Change-Id: Ifa9ec5bcb8b25b6334b589e4bc7bcb915e85e349
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49349
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable all NIDs other than those for the front combo jack.
Adjust attributes to match jack physical location, appearance, etc.
Correct group number for verbs for HDMI output.
Test: run hdajackretask, verify NID characteristics correct for each
verb. Verify headphone detection and output functional.
Change-Id: If9fca5d9795d56bd38c8ea47f8de985c14ac8fab
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49464
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the USB2 port 3/4/9
1. USB2 port3 assign to WWAN, and elemi have no WWAN.
2. USB2 port4/port9 connect to Type-C C1/C0
BUG=b:177483059
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I9affc69cc325b5eb0219b50bfe46f66eb0bb2016
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49473
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: Ie122a441145383b820d96e32ce1581dfc27fa57b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
They all operate on that file, so just add it globally.
Change-Id: I953975a4078d0f4a5ec0b6248f0dcedada69afb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We no longer need the IO-APIC assignments since we use the GNB IO-APIC.
We were also missing the E-H IRQ mapping. I also renumbered them since
IRQ 8 is used by the rtc.
TEST=none
BRANCH=zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia956ae457669aeda6fa49e127373aad3807f7b9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Two configuration files are added:
1. H9HCNNNFAMMLXR-NEE-8GB: new byte mode
2. MT53E1G32D2NP-046-4GB: new single rank mode
Also initialize the rank number field 'rank_num' for all configs.
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: I1786c1e251e8d6e110cbdce79feeb386db220404
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49108
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The fw_config field SPI_SPEED is not used for zork devices.
To define SAR config, use the fw_config bit[23..26].
Then vilboz can loaded different WiFi SAR table for different SKUs.
BUG=b:176858126, b:176751675, b:176538384
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5ba98799e697010997b515ee88420d0ac14ca7ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on voema schematics, two USB2 ports 3 and 5 are assigned to type C
connectors on Voema board.
BUG=b:177483061 b:172535001
TEST=Build and boot Voema.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I12cef85595e511801ab9c563ae4aa26e25875679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
Early gpio configuration was done in romstage, while LPC pads were
configured in bootblock. Instead of adding another dedicated gpio table
for bootblock, move early gpio configuration completely to bootblock on
these boards. This won't hurt, since there is no code touching the pads
in between.
The soc code gets dropped in CB:49410.
Change-Id: I2a614afb305036b0581eac8ed6a723a3f80747b3
Tested-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Basking Ridge is not ULT, thus does not support C-states deeper than C7.
Replace them with the values used by all other Haswell non-ULT boards to
allow subsequent commits to cleanly factor them out of the devicetree.
Change-Id: Ife34f7828f9ef19c8fccb3ac7b60146960112a81
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46907
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module is not expected to be powered off during warm reset. Hence
configure the LTE_PWR_OFF_ODL (GPP_A10) gpio pad reset configuration to
PWROK and set the TX state to 1.
BUG=b:163100335
BRANCH=dedede
TEST=Verified through the waveforms that power sequence is meeting the LTE module requirements.
Change-Id: I8676da6186559288aabe078b6158fc01075c7b41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
LTE module used in metaknight has a specific power on/off sequence.
GPIOs related to power sequence are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: GPP_A10 keeps high, GPP_H17 goes low at least 2ms
Configure the GPIOs based on these requirements.
BUG=b:173671094
TEST=Build and boot Metaknight to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ibff16129dfe2f1de2b1519049244aba4b3123e52
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
make olddefconfig on other projects using USE_VENDORCODE_ELTAN results in error.
USE_VENDORCODE_ELTAN unmet direct dependencies.
Remove dependency on VBOOT for USE_VENDORCODE_ELTAN.
TEST = Build and boot on Facebook FBG1701
Change-Id: I5881c334955c73ae0f1a693f95ceb1aee62ee898
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
The default value is not sufficient to correctly configure the Type-C
ports as it has all ports disabled by default. On Volteer ports 0
and 1 are enabled so setting this value to 0x3 and correctly
keeping the IomPortPadCfg values at 0 for ports that have a
retimer and ports that are not configured. These values were set
to 0x90000000 to avoid s0ix issues which arose from the UsbTcPortEn
value being incorrect.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that s0ix cycles complete
without any issues
Change-Id: Ib4f2bd0f68debd4e97ccaab9e1d8a873dc4e4d9f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48814
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Target added to INTERMEDIATE all operate on coreboot.pre, each modifying
the file in some way. When running them in parallel, coreboot.pre can be
read from and written to in parallel which can corrupt the result.
Add a function to create those rules that also adds existing
INTERMEDIATE targets to enforce an order (as established by evaluation
order of Makefile.inc files).
While at it, also add the addition to the PHONY target so we don't
forget it.
BUG=chromium:1154313, b:174585424
TEST=Built a configuration with SeaBIOS + SeaBIOS config files (ps2
timeout and sercon) and saw that they were executed.
Change-Id: Ia5803806e6c33083dfe5dec8904a65c46436e756
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49358
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the functions that get called by the coreboot console
initialization code aren't in the SOC-specific code anymore, the SOC's
uart.c can be included unconditionally in the build now. This also
replaces the STONEYRIDGE_UART Kconfig option with the common
AMD_SOC_CONSOLE_UART one.
Change-Id: I09c15566a402895d6388715e8e5a802dc3c94fdd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update PL1 min and max values for Delbin systems
BUG=b:168958222
BRANCH=None
TEST=Build and verify on delbin system
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: I2152f0dbeb0ae463b78464571b6c434830f0082a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:174338903
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I875f6b32c4053ef6d23ad7606cd35a129a78c306
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49290
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initiate overridetree.cb based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I31e5ac1703476083ac71dac30b0a3299b38384c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Follow latest schematic to fill gpio table.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a983605b5139ff8510a0cf225e6564b9215cb1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Two USB2 ports 4 and 9 are assigned to type C connectors on Voxel board.
This update configures these USB2 ports for Type C which will allow USB2
port reset message upstream from PCH to CPU to recover a USB3 device
that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Voxel board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia370a449a41701e690c1c507d70bedfce2076a65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The FW config takes 2 bits for USE_FAN[27,28].
So FW_CONFIG_SHIFT_WWAN value should be 29.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ica6d04f9c48aa0800189283608bf57416ac75cf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49236
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:171757619
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I37390535e263b4b9547ad7307278e3360ba836bd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:176536593
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wayne3_Wang <wayne3_wang@pegatron.corp-partner.google.com>
Change-Id: I69962a5b7c7c464280b35c834f7ee1c9b77db6fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49197
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While FORCE_PWR is set high, it prevents retimer from entering low power
state. S0ix failure occurs while USB4 Gatkex is connected on Port-0.
This change sets FORCE_PWR(GPP_H10) low. This FORCE_PWR GPIO will be
toggled by kernel through DSM method while updating retimer firmware.
BUG=b:174166586
Cq-Depend: chromium:2594438
TEST=Verifed s0ix cycles with USB4 Gatkex connected on Port-0.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ie4b442e1078379c522a94bfdc00cd99e6f9b8170
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To work around various bugs running KVM enabled, copy page tables to
DRAM in assembly before jumping to x86_64 mode.
Tested on QEMU using KVM, no more stange bugs happen:
Tested on host
- CPU Intel(R) Core(TM) i7-7700HQ
- Linux 5.9
- qemu 4.2.1
Used to crash on emulating MMX instructions and failed to translate
some addresses using the virtual MMU when running in long mode.
Tested on host
- CPU AMD EPYC 7401P 24-Core Processor
- Linux 5.4
- qemu 4.2.1
Used to crash on jumping to long mode.
Change-Id: Ic0bdd2bef7197edd2e7488a8efdeba7eb4ab0dd4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
List of changes:
1. Create new Kconfig MAX_CPU_ROOT_PORTS and MAX_PCH_ROOT_PORTS as per
EDS.
2. Add new chip variable to enable/disable CPU PCIE RPs from mainboards.
3. Rename PcieRpEnable to PchPcieRpEnable.
4. Enable CPU RPs as below in mainboard devicetree.cb
RP1: PEG60 : 0:6:0 : CPU SSD1
RP2: PEG10 : 0:1:0 : x8 CPU Slot
RP3: PEG62 : 0:6:2 : CPU SSD2
Change-Id: I92123450bd7cfb2e70aae8de03053672a7772451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49136
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These boards without ChromeEC do not set ACTIVE_EC_RW
flag as part of the gnvs_assign_chromeos() function.
Create abstraction to avoid <vendorcode/chromeos/x> include.
Change-Id: Ic6029e1807fcfe7dd2c766ce8221e347b6b096f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48777
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Already done in common gnvs_get_or_create() implementation
once gnvs_chromeos_ptr() is defined for platforms.
Change-Id: I90fa2bc28ae76da734b3f88be057435aed9fe374
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48703
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allocation now happens prior to device enumeration. The
step cbmem_add() is a no-op here, if reached for some
boards. The memset() here is also redundant and becomes
harmful with followup works, as it would wipe out the
CBMEM console and ChromeOS related fields without them
being set again.
Change-Id: I9b2625af15cae90b9c1eb601e606d0430336609f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48701
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of hard-coding function names in strings, use the __func__
constant for better maintainability.
Change-Id: I151560cd5a135e00f494eda3f9d3b592ee9d984a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add a space after each comma to fix linter issues.
Change-Id: I5533c4fc7aa0e986da4350ec56b84903b3111a07
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Macros should not use a trailing semicolon.
Change-Id: Ibbcd589c7afa72e9e468e5f4b557bb2c665bbec0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Align the bytes of picr_data[] and intr_data[] with 8 bytes per line and
add spaces after commas so that the linter doesn't complain.
Also, remove spaces before the postfix '++' operator.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Change-Id: I90bec7fdfabca6f8afd1508c673241e0742e2ee9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49191
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop VR configuration since it matches the platform defaults.
Change-Id: I92007f4ff9d093c9573bb1ee13e64eb2f38af4f4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Two USB2 ports 4 and 9 are assigned to type C connectors on Delbin
board. This update configures these USB2 ports for Type C which will
allow USB2 port reset message upstream from PCH to CPU to recover a USB3
device that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Delbin board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Idb3ce949e1ecf3adc7615e0af79a38a0cc9be18f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49202
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:174118027
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Signed-off-by: Marco Chen <marcochen@google.com>
Change-Id: Id37c4c5716ade0851cfcb24e12b390841e633ac9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
This change adds internal USB camera into devicetree for sasuke
BUG=None
TEST=Built and checked camera device existence with lsusb
Change-Id: I51b9bb174205d984f1d060afd603f1d087095645
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49162
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds ELAN touchpad into devicetree for sasuke.
BUG=None
TEST=Built and verified touchpad function
Change-Id: If9c25f23ee1c0e88382fff036f77a6753775b81e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change adds DA7219 audio codec and MAX98360A amplifier for sasuke.
BUG=None
TEST= Built and heared speaker sound on OS
Change-Id: Ib48eb74fbfe171d46d0d23859057ba169b56bde2
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Drop DEVICETREE from Kconfig since it matches the default value.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Change-Id: Idbcd49cca6494ae2da0f364c24638d7ca11911da
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It doesn't make sense to configure that filename in Kconfig, since the
filename can be changed by the user. So remove it.
Change-Id: I3eed05637da29096bc1d134505d7335db5db1439
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49138
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add memory table to "mem_list_variant.txt", and command to generate files:
go run ./util/spd_tools/lp4x/gen_part_id.go src/soc/intel/tigerlake/spd src/mainboard/google/volteer/variants/copano/memory/ src/mainboard/google/volteer/variants/copano/memory/mem_list_variant.txt
DRAM Part Name ID to assign
MT53D512M64D4NW-046 WT:F 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
BUG=b:175896481
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I2ace17e8fff12d3f5de15a35f609265d8b6ed6b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48948
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that the _PRT generates a GNB IO-APIC routing table we no longer
need to route the PCI interrupts through the FCH IO-APIC. This change
unmaps the IRQs since they are no longer used.
BUG=b:170595019
TEST=Boot with `pci=nomsi amd_iommu=off` and verify /proc/interrupts
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3467934bfcac14311505bec49a12652490554e6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
As part of acoustic noise mitigation calibration, we need to enable
FastPkgCRampDisable upd along with slew rate = 1. This values has been
derived based on noise calibration done.
Please refer document 575216 for procedure.
BUG=None
BRANCH=dedede
TEST=correct value has been programmed and slew rate measurement
is correct on scope.
Change-Id: Ie42c8ab647ff42fa043b6f717a9834f9b9c551f6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
