Pushing EOP msg post FSP notify helps to save ~30ms+ boot time across
various warm reboots.
This patch ensures late sending EOP msg when function disabling of CSE
is no longer a requirement.
BUG=b:200644229
TEST=Able to save ~30ms+ of boot time
Without this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,248,328(61,954))
With this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,231,660 (2,754)
Change-Id: I2b78a1c07803aacfb34dce9e94b2a05a2491aabc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures soc_finalize() is getting called at the entry of
BS_PAYLOAD_BOOT boot state instead of BS_PAYLOAD_LOAD, BS_ON_EXIT.
The purpose of this change is to accommodate more time to push out
sending CSE EOP messages at post.
BUG=b:200644229
TEST=coreboot serial log suggests soc_finalize() is getting called
as part of the BS_PAYLOAD_BOOT entry.
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
BS: BS_PAYLOAD_BOOT entry times (exec / console): 21 / 15 ms
Change-Id: I8632eca057255d7f4a38b64fd17c1f3d84123051
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Prior to coreboot sending EOP messages during post, it's important to
ensure that CSE is not in Idle state. In case CSE is in Dev Idle
state (which means D0I3 bit is set), reset this bit before sending
EOP command.
This patch ensures coreboot has provision to send CSE EOP messages even
after the FSP Notify phase without any delays waiting for the device
to respond or timeout.
BUG=b:200644229
TEST=Able to send CSE EOP message even after FSP Notify phase.
Attempting CSE EOP msg sending post FSP notify without this code change
causes `timeout` issue as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 171 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
HECI: timed out reading answer!
HECI: Failed to receive!
HECI: receive Failed
HECI: EOP send/receive fail
ERROR: Failed to send EOP to CSE, 2
cse: CSE status registers: HFSTS1: 0x90000255, HFSTS2: 0xf10516 HFSTS3:
0x20
VB2:vb2api_fail() Need recovery, reason: 0x31 / 0xc
Saving nvdata
board_reset() called!
full_reset() called!
Attempting CSE EOP msg sending post FSP notify with this code change
is `successful` as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 170 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
CSE: EOP requested action: continue boot
CSE EOP successful, continuing boot
Change-Id: Iae1bc52e94b08f97004424ea0c147d6da8aca6e2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures APIs that are responsible for CSE device state
transition between active to idle and vice-versa are available
publically for other modules/boot stages to consume.
BUG=b:200644229
TEST=Able to build and boot ADLRVP-P.
Change-Id: Ia480877822d343f2b4c9bf87b246812186d49ea3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These platforms no longer use reg-script. Drop unneeded select.
Change-Id: I8fc4dc29d25dffbf9ed1947d0ff013b2fae0faaf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: I87d1278360a231cbe5b5f825ad9a448e59e63ea2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: Ib3c83131c30fd02c579b910cfad6843eb28ba8f1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The current names of the PMC init/enable callbacks are very confusing.
Rename them.
Change-Id: I69f54f3b4e1ea9a9b4fa5c8dd9c0d454d7cd1283
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Rename the `ecps` GNVS struct member to `epcs` to match the name in ASL.
Change-Id: I1f6b97309eea75e7dbb4e5e664660df05ec0845e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This CL adds support for new ADL-M graphics Device ID 0x46c3.
TEST=boot to OS
Change-Id: Ib55fb501f96fe9bcc328202511bbfe84a3122285
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add ADLP 242 sku power related settings, which follow the settings of
ADLP 282 sku (both are 15w).
BUG=b:201253904
TEST=Build and check fsp log to confirm the settings are set properly.
Change-Id: I829dd690c22d167a507b1910106da06b275cec09
Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The UPDs for PM power cycle duration and SLP_* signal durations are all
identical to Tiger Lake, so add similar support, but use enums instead
of comments to represent the durations symbolically.
BUG=b:184799383
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a531f042658894bcbc6a76eff453c06e90d66b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57891
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These methods are never used in the code. Drop them.
Change-Id: If5568b494f821d2647ada5ae845bcd015708520e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
These fields are never used in the code. Drop them.
Change-Id: Icd07f2d704c19126bf6df4d740c21d5a1342061b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This field is never used in the code. Drop it.
Change-Id: I88207ec369ab83823ef2f3fc40f68a0980ce9663
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The current MRC binaries for Bay Trail are always ELF files. Always
adjust the position in CBFS using the ELF header regardless of file
names. Without adjusting the position, the system hangs right after
calling into MRC.
TEST: MRC position in CBFS does not change for bostentech/gbyt4.
Change-Id: I74e1246a5fac3f3649be9842ff13c2fc70f72a20
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57989
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This file does not exist in the coreboot tree. One should place this
file in the `site-local` subdirectory and specify the paths by means
of `site-local/Kconfig`.
Change-Id: I86ac2a6176947f12194bec6b63bedd7db79820a0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
`intel_microcode_find()` function uses cached ucode data hence it would
avoid locating ucode.bin from CBFS while passing ucode.bin pointer to
FSP.
Change-Id: I8f92c9f20dfb055c19c6996e601c8c24767aecb7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change replaces the device tree walks with device pointers by
using alias for tcss_usb3_port* devices.
Change-Id: I65d9c83a9d0aab5a42f5a7cc6df98a154e79d16a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Explicitly point out that gpio_configure_pads_with_override will ignore
GPIOs that are only in the override configuration, but not in the base
configuration.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1bdfcac89b81fef773938133a2699897c6ee9415
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some headers in vendorcode are still needed but the UPD definitions
can be taken from the FSP repo.
Change-Id: I7bb96649ecba9d313cfce50af202aabcf610680f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
coreboot expects different names for FSP UPDs so use some CPP to make
it happy.
Change-Id: I4b2c2dd6ba40cb58bc2089eb9204fd4f70b037aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
There is another gpio group, namely HVCMOS, between GPP_C and GPP_E. Add
it, so the group index calculation for GPI/SMI/NMI results in the
correct value.
Reference: Linux linux/drivers/pinctrl/intel/pinctrl-icelake.c
Change-Id: I7725191173ddc0d43bbe940cdf3b0dc2aa3e5f8d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all dedede variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for cret:
util/spd_tools/bin/part_id_gen \
JSL \
lp4x \
src/mainboard/google/dedede/variants/cret/memory \
src/mainboard/google/dedede/variants/cret/memory/mem_parts_used.txt
For cappy, the Makefile.inc was manually modified to use the new
placeholder value.
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/dedede -a -x --timeless
Change-Id: I2871ff45d6202520d4466b68a4d5bb283faf2b63
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all volteer variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for voema:
util/spd_tools/bin/part_id_gen \
TGL \
lp4x \
src/mainboard/google/volteer/variants/voema/memory \
src/mainboard/google/volteer/variants/voema/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/volteer -a -x --timeless
Change-Id: Ibd4f42fd421bfa58354b532fe7a67ee59dac5e1d
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all brya variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for anahera:
util/spd_tools/bin/part_id_gen \
ADL \
lp4x \
src/mainboard/google/brya/variants/anahera/memory \
src/mainboard/google/brya/variants/anahera/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using: abuild -p none -t google/brya -a -x --timeless
Change-Id: I08efe1d75438c81161d9b496af2fa30ce6f59ade
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Earlier generation platform used `HeciEnabled` chip config (set to 0)
and HECI_DISABLE_USING_SMM Kconfig to make the CSE function disable at
the end of the post. `HeciEnabled` chip config remains enabled in all
latest generation platforms hence drop HECI_DISABLE_USING_SMM Kconfig
selection from SoC Kconfig as CSE remains default enabled.
BUG=b:200644229
TEST=No functional impact during boot as CSE (B:0, D:0x16, F:0) device
is listed with `lspci`.
Change-Id: I5278e5c2e015b91bb3df3a3c73a6c659a56794b5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I95753fa536fae8ca4bb95007419875815c1bcb06
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I1a55df754c711b2afb8939b442019831c25cce29
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Idfaa9a24f7b7fefa4f63ab8e3bc4ee6a0f1faedf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Ie86822f22aa5899a7e446398370424ca5a4ca43d
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Currently, Intel TME (Total Memory Encryption) can be enabled regardless
of SoC support. Add a Kconfig to guard the option depending on actual
support.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia20152bb0fc56b0aec3019c592dd6d484829aefe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Migrate the last two platforms to using Kconfig through
`get_valid_prmrr_size()` instead of hardcoded values in the devicetree.
Change-Id: I93aa177f741ca8b2a2d50fae2515606b96784e83
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
vboot_reference is introducing a new field (ctx) to store the current
boot mode in crrev/c/2944250 (ctx->bootmode), which will be leveraged
in both vboot flow and elog_add_boot_reason in coreboot.
In current steps of deciding bootmode, a function vb2ex_ec_trusted
is required. This function checks gpio EC_IN_RW pin and will return
'trusted' only if EC is not in RW. Therefore, we need to implement
similar utilities in coreboot.
We will deprecate vb2ex_ec_trusted and use the flag,
VB2_CONTEXT_EC_TRUSTED, in vboot, vb2api_fw_phase1 and set that flag
in coreboot, verstage_main.
Also add a help function get_ec_is_trusted which needed to be
implemented per mainboard.
BUG=b:177196147, b:181931817
BRANCH=none
TEST=Test on trogdor if manual recovery works
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I479c8f80e45cc524ba87db4293d19b29bdfa2192
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57048
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FspMultiPhaseSiInit API was introduced with FSP 2.2 specification
onwards. EnableMultiPhaseSiliconInit is an arch UPD also introduced
as part of FSP 2.2 specification to allow calling FspMultiPhaseSiInit
API.
However, some platforms adhere to the FSP specification but
don't have arch UPD structure, for example : JSL, TGL and Xeon-SP.
Out of these platforms, TGL supports calling of FspMultiPhaseSiInit
API and considered EnableMultiPhaseSiliconInit as a platform-specific
UPD rather than an arch UPD to allow calling into FspMultiPhaseSiInit
API.
It is important to ensure that the UPD setting and the callback for
MultiPhaseInit are kept in sync, else it could result in broken
behavior e.g. a hang is seen in FSP if EnableMultiPhaseSiliconInit
UPD is set to 1 but the FspMultiPhaseSiInit API call is skipped.
This patch provides an option for users to choose to bypass calling
into MultiPhaseSiInit API and ensures the EnableMultiPhaseSiliconInit
UPD is set to its default state as `disable` so that FSP-S don't
consider MultiPhaseSiInit API is a mandatory entry point prior to
calling other FSP API entry points.
List of changes:
1. Add `FSPS_HAS_ARCH_UPD` Kconfig for SoC to select if
`FSPS_ARCH_UPD` structure is part of `FSPS_UPD` structure.
2. Drop `soc_fsp_multi_phase_init_is_enable()` from JSL and Xeon-SP
SoCs, a SoC override to callout that SoC doesn't support calling
MultiPhase Si Init is no longer required.
3. Add `FSPS_USE_MULTI_PHASE_INIT` Kconfig for SoC to specify if
SoC users want to enable `EnableMultiPhaseSiliconInit` arch UPD (using
`fsp_fill_common_arch_params()`) and execute FspMultiPhaseSiInit() API.
4. Presently selects `FSPS_USE_MULTI_PHASE_INIT` from IA TCSS common
code.
5. Add `fsp_is_multi_phase_init_enabled()` that check applicability of
MultiPhase Si Init prior calling FspMultiPhaseSiInit() API to
honor SoC users' decision.
6. Drop `arch_silicon_init_params()` from SoC as FSP driver (FSP 2.2)
would check the applicability of MultiPhase Si Init prior calling
FspMultiPhaseSiInit() API.
Additionally, selects FSPS_HAS_ARCH_UPD for Alder Lake as Alder Lake
FSPS_UPD structure has `FSPS_ARCH_UPD` structure and drops
`arch_silicon_init_params()` from SoC
`platform_fsp_silicon_init_params_cb()`.
Skip EnableMultiPhaseSiliconInit hardcoding for Tiger Lake and uses
the fsp_is_multi_phase_init_enabled() function to override
EnableMultiPhaseSiliconInit UPD prior calling MultiPhaseSiInit FSP API.
TEST=EnableMultiPhaseSiliconInit UPD is getting set or reset based on
SoC user selects FSPS_USE_MULTI_PHASE_INIT Kconfig.
Change-Id: I019fa8364605f5061d56e2d80b20e1a91857c423
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch selects SOC_INTEL_COMMON_BLOCK_TCSS from Alder Lake SoC
Kconfig and drops SOC_INTEL_COMMON_BLOCK_TCSS Kconfig selection from
specific mainboard (brya) to ensure all Alder Lake mainboards can make
use of common TCSS block.
BUG=b:187385592
TEST=Type-C pendrive/Gen-2 SSD detected as Super speed.
Change-Id: I85f6a967eb34ea760418131a9586bfdeb13c9b5d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Commit 2eb100dd12 added PMC LPM requirements to the the PEP ACPI
objects, but it was not made clear that one of the pointer arguments to
the mentioned function is not supposed to be NULL and Coverity
complained. Make the intention clear by instead asserting that `info`
cannot be NULL.
Fixes: Coverity CID 1462119
Change-Id: I9e8862a100d92f4a7ed1826d3970a5110b47f4c4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
When the FSP driver fills out framebuffer information for the coreboot
tables, it assumes the orientation is always normal. This patch provides
a field for a mainboard to override the panel orientation from the
default (LB_FB_ORIENTATION_NORMAL). Later patches will have the FSP
driver use this value when filling out framebuffer information.
BUG=b:194967458
BRANCH=dedede
Change-Id: I559b3d6a076112a1c020ce5e296430d7ccba9ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add igd device name in soc_acpi_name(), and src/drivers/gfx/generic
can generate device in GFX0 scope in ssdt.
BUG=b:198188272
TEST=emerge-brya coreboot and check ssdt.
Change-Id: Id0c50254a8a25b47368e932c99243f4f02250b82
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fixes:
27c51a0 ("Revert "soc/intel/broadwell/pch: Replace ACPI device NVS"")
which reverted the removal of device NVS, but was not boot tested on any
Broadwell Chromebooks. It was recently discovered that the DNVS
object was not being loaded, due to a weak function setting the size
as zero not being defined for the platform/soc. Add the missing
overloaded function and required headers.
Test: build/boot google/auron variants LULU ans SAMUS, verify
touchpad functional and no ACPI errors in kernel boot log.
Change-Id: Icd317d117dbb068bb6da80fe56c06c0267c7b2ae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Intel TGL BIOS specification (doc ##611569) Revision 0.7.6 Section
7.2.5.1.5 recommends reserving the following resources for each PCIe
USB4 root port:
- 42 buses
- 194 MiB Non-prefetchable memory
- 448 MiB Prefetchable memory
This change enables reserving of resources for USB4 when mainboard
selects the newly added Kconfig SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES.
This is similar to the change for ADL in commit 8d11cdc6fa
("soc/intel/alderlake: Add Kconfig for recommended PCIe TBT resources").
Change-Id: I25ec3f74ebd5727fa4b13f5a3b11050f77ecb008
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
After switching to runtime generation of the Intel Power Engine (PEPD)
device, this file is no longer required.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I2444433f08bfda6f79589a397a2ad2b5a3ecb0ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The pep.asl file is being obsoleted by runtime generation, therefore
switch skylake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7c7cb424278946a9767ea329d18fb03d4e57dce8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to get rid of pep.asl, skylake also needs to support runtime
generation of the Intel Power Engine, therefore add this support to
devices that have a discoverable PMC as well.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4bf0c4a338301b335fa78617e0f2ed5a9f4360ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The pep.asl file is being obsoleted by runtime generation, therefore
switch elkhartlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I47f03b440729d4b37ae0abc84bd1d18c4e01657d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The pep.asl file is being obsoleted by runtime generation, therefore
switch jasperlake boards to this method.
soc/intel/jasperlake: Switch to acpigen PEPD
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib7f17f9b3b1396708ba68fa7a6d199d6e8b0ba11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Now that the PMC device is marked as hidden in devicetrees, the device
callbacks can be used instead of BOOT_STATE_INIT_ENTRY callbacks.
Note that this moves PMC initialization from BS_DEV_INIT_CHIPS to
BS_DEV_ENUMERATE, which aligns with other Intel SoCs.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If292728ad975ba803fed6abea879f6f634470a11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The pep.asl file is being obsoleted by runtime generation, therefore
switch tigerlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8e97c589273e934e89d69d8829680b9cac1ff9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The LPM enable mask is useful to have in more than one place, therefore
more the get_disable_mask() function and its helpers to lpm.c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ibe83dc106f5f37baf9d5c64f68c47d85ea4e6dd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56460
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The pep.asl file is being obsoleted by runtime generation, therefore
switch alderlake boards to this method.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I617bc3d1c3cf4ac6b6cbbd790dcf62e731024834
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is a use-case for generating the AML bytecode at runtime for the
Intel Power Engine device, which comes in a followup patch.
BUG=b:185437326
TEST=verified on google/brya and google/dratini by dumping SSDT and
verifying the PEPD device matches what was previously in the DSDT:
Scope (\_SB.PCI0)
{
Device (PEPD)
{
Name (_HID, "INT33A1")
Name (_CID, EisaId ("PNP0D80")
Method (_DSM, 4, Serialized)
{
ToBuffer (Arg0, Local0)
If ((Local0 == ToUUID ("c4eb40a0-6cd2-11e2-bcfd-0800200c9a66")))
{
ToInteger (Arg2, Local1)
If ((Local1 == Zero))
{
Return (Buffer (One)
{
0x63
})
}
If ((Local1 == One))
{
Return (Package (0x01)
{
Package (0x03)
{
\NULL,
Zero,
Package (0x02)
{
Zero,
Package (0x02)
{
0xFF,
Zero
}
}
}
})
}
If ((Local1 == 0x02)){}
If ((Local1 == 0x03)){}
If ((Local1 == 0x04)){}
If ((Local1 == 0x05))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (One)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (One)
}
If (CondRefOf (\_SB.PCI0.EGPM))
{
\_SB.PCI0.EGPM ()
}
}
If ((Local1 == 0x06))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (Zero)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (Zero)
}
If (CondRefOf (\_SB.PCI0.RGPM))
{
\_SB.PCI0.RGPM ()
}
}
Return (Buffer (One)
{
0x00
})
}
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie83722e0ed5792e338fc5c39a57eef43b7464e3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the get_supported_lpm_states() function to set the respective FSP
UPD.
TEST=with patchtrain on brya0,
/sys/kernel/debug/pmc_core/substate_requirements shows only the
substates that are applicable to the design (S0i2.0, S0i3.0).
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I5bb8b3671e78c5f2706db2d3a21b25cf90a14275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This function searches the known MCH device IDs for Alder Lake and
returns the appropriate enum value representing ADL-P, ADL-M, ADL-S, or
unknown.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I26354b340e0c5f15ba246c1cb831d7feaf62d2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Default VBOOT_HASH_BLOCK_SIZE is 1 KiB and increasing it to 4 KiB
helps in improving overall boot time since it reduces hashing and
body loading time.
Increasing it over 4 KiB doesn't result in significant improvement,
thus keeping the value at 4 KiB as of now.
Timing data:
Note that before Data is with 1 KiB block size.
|------------------------------------------------------|
| Stage | Block Size | Before | After |
|finished loading body| 4 KiB | 205,187 | 189,947 |
|finished loading body| 8 KiB | 205,187 | 188,708 |
|finished loading body| 16 KiB | 205,187 | 188,085 |
|finished loading body| 32 KiB | 205,187 | 187,793 |
|------------------------------------------------------|
BUG=b:188577893
BRANCH=None
TEST=Boot time for Brya improves by 20 - 25 msec
Change-Id: I9222761c7d58e4a370d3a41c651b6c169599d792
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change sets Irms config in FSP if TdcTimeWindow and TdcCurrentLimit
is set to non zero. It results VR TDC Input current to be treated as it
is root mean square.
This change also optimizes the check of TdcTimeWindow and TdcCurrentLimit
for TdcEnable UPD.
BRANCH=None
TEST=Build and boot brya with debug FSP and verify Irms UPD value
from logs
Change-Id: Ice5c775ef9560503109957a1ed994af1d287aafc
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
From ACPI specification, version 6.2 Errata A:
A `duty_width` value of 0 indicates that processor duty cycle is not
supported and the processor continuously runs at its base frequency.
Because Broadwell sets `duty_width` to 0, processor duty cycle is not
supported, and the value of `duty_offset` is ignored. For consistency
with Lynx Point, set `duty_offset` to 0.
Change-Id: I68cb85ec32a6cceda0cea29d76df6c6219b78a40
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The code under `cpu/x86/tsc` is only compiled in when its `Makefile.inc`
is included from platform (CPU/SoC) code and the `UDELAY_TSC` Kconfig
option is enabled.
Include `cpu/x86/tsc/Makefile.inc` once from `cpu/x86/Makefile.inc` and
drop the now-redundant inclusions from platform code. Also, deduplicate
the `UDELAY_TSC` guards.
Change-Id: I41e96026f37f19de954fd5985b92a08cb97876c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57456
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow to select the primary graphics device between the IGD and the
external PCIe GPU depending on the ONBOARD_VGA_IS_PRIMARY config.
The option sets the priority only. This means that if a high priority
is set for an external PCI device and it is not connected/not enabled,
then the device with a lower priority will be used, in our case it is
IGD.
TEST = Set PRIMARY_PCI and boot Linux on the Kontron mAL10 [1] with
the miniPCIe video adapter on the Silicon Motion SM750 controller. As
a result, the display connected to an external GPU device shows the
Tianocore logo + setup menu and the desktop.
[1] https://review.coreboot.org/c/coreboot/+/39133
Change-Id: Idcd117217cf412ee0722aff52db4b3c8ec2a226c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Get rid of several unused PCH PCI device macros. These macros expand to
a call to the `pcidev_path_on_root_debug()` function, which only exists
to debug bad code. If needed, these macros should be reimplemented with
the `pcidev_path_on_root()` function instead.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I366e064f3fe708b55fb381aee25b2795b1c61142
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change adds a new Kconfig `SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES`
that can be selected by mainboard to reserve hotplug resources for
USB4 at the SoC level. `ADL_ENABLE_USB4_PCIE_RESOURCES` is dropped
from soc/intel/alderlake and instead the newly added Kconfig is now
used. This new Kconfig is added so that the same config can be used
across different platforms. In following changes, this Kconfig is
utilized by TGL as well.
Change-Id: Id7c359a0e255c43c2732f6cbe287bc7da14a46e3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There are multiple HECI clients in the CSE. heci_send_receive() is
sending HECI messages to only the MKHI client. Add an argument to
heci_send_receive() function to provide flexibility to the caller to
select the client for which the message is intended.
With the above change heci_send() and heci_receive() functions are
no longer required to be exposed.
In the follow-up patches there will be messages sent to one other
client.
BUG=None
BRANCH=None
TEST=Build and boot brya. HECI message send and receive to MKHI client
is working. Also, MEI BUS message to disable bus is working.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: Icde6d0155b62472b6a7caadc5fc8ea2e2ba6eb0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add tpch device information for thermal functionality under dptf
for alderlake soc based platform.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Iad8e8bc0b7a104bbe582bc477936d0d00087f1d1
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add PMC IPC commands information for FIVR control functionality.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Iccb43b7ba4f0765499bf1844efbbb526bd671a8f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently maximum VBT data size for Jasper Lake is 8KB, but Bugzzy
would use VBT data over 8KB. This change makes use of Kconfig option to
increase the maximum VBT data size to 9KB for Jasper Lake.
BUG=b:194029827
BRANCH=dedede
TEST=build and boot bugzzy and verify fw screen is loaded
Change-Id: I0abe1ba5609b48a8a8b15f88bec28342ce26c78f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57201
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: Ib6fce70d6b0386906850884880dadbf45597452d
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: I6ae22f9df4834508dfa304050fad44d45df45334
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: I10f859f30b260d012f0bc8755f32413d8b2cf267
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set power limit values dynamically based on CPU TDP and PCI ID of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Ic331a3debb076ef08a312a31edc1468974fd4902
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57035
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get tdp value of CPU for different SKUs based on PKG POWER MSR.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I9fba0a64da2f1d79d633054dddd9fdf1d3d8e258
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Set the `UserBd` FSP-M UPD to `BOARD_TYPE_DESKTOP` by default on PCH-H.
Remove now-redundant mainboard code to set the `UserBd` UPD.
Change-Id: I349abe5d89f562c158ce9baadbca2b2f56695846
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57261
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Specify the type of the `DIMM_MAX` Kconfig symbol once.
Change-Id: I2e86baaa8bd50c7b82c399fde5dcea05da6b4307
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Processor hang is observed while hot plug unplug of TBT device. BIOS
should execute TBT PCIe RP RTD3 flow based on the value of
TBT_DMA_CFG_VS_CAP_9[30]. It should skip TBT PCIe RP RTD3 flow, if
BIT30 in TBT FW version is not set.
BUG=b:194880254
Change-Id: Ie3577df519f64c6f7270dc5537278af76536774e
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56503
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Make `mainboard_fill_spd_data` mandatory and adapt mainboards to define
this function accordingly.
Change-Id: Ic18c4c574e8c963bbb41c980f43bdbacc57735af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55806
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the `mainboard_fill_spd_data` function out of romstage, in
preparation to confine `pei_data` usage to as few files as possible.
Change-Id: I6447da4d135d920f9145e817bfb7f9056e09df84
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55805
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change calls `add_more_links()` in `denverton_init_cpus()` if
`dev->link_list` is NULL. This condition can occur if mainboard does
not add any APIC device in the device tree.
Link: https://mail.coreboot.org/hyperkitty/list/coreboot@coreboot.org/thread/YLMK2FBWWL6RKDNKBVZB3NJDYMEYHED7/
"A different lapic number in devicetree.cb needed for CPU with the
same SKU and steping (Intel Atom C3538)."
Change-Id: I6f453901b17f7eff22beed8dbf6995cdc9f9b776
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57152
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Suresh Bellampalli <suresh.bellampalli@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: Ice4c727f2b75893cd012345a556fd21d9807dfaa
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
TEST=boot to OS, read PCI 0:0.0 config register 0x80, value is 0x31
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0c3e16edeab6f85a79eb10e1477d95952b554a18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some FSPs provide a UPD to allow the bootloader to set the PAM lock bit
instead of the FSP, therefore add a function in the common code to do
this. Source: ADL & TGL FSP integration guides
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1d6642b496617b6e8ccda8a0aa6bfd88ea9dc3ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Cannon Point PCH-H does not implement the eMMC, I2C4 and I2C5 devices.
Guard the IRQ constraints for these devices to prevent FSP assertions.
Tested on Prodrive Hermes, debug FSP builds no longer fail to boot.
Change-Id: I58674d1c3c5fe4535c022020674d48d6a5315bf9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Prepare to confine all `pei_data` references in raminit.c and refcode.c
so that mainboards don't need to know about its existence.
Change-Id: I55793fa274f8100643855466b6cca486896fb2c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55801
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do early ME init before adding the "start of raminit" timestamp.
Change-Id: If8b27a9d4eb3b801e3e05dc2f2b95bf748985707
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55800
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the base TGL devicetree, add one specific to TGL-H that adds
the additional supported devices.
Introduces a new Kconfig for selecting the PCH support.
Reference:
- Intel doc 615985
Change-Id: Icc130461edcecc4a3e1f6544ccb905608881d2f7
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Convert the power limit defines to an enum and add TGL-H entries.
Change-Id: I6fa7c7338b3157b29ff72769238597e3c528aedb
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 34bd6ba979.
Reason for revert: Device NVS is expected by mainboard samus
in payload depthcharge:
932c6ba270/src/board/samus/board.c (60)
Not reverted:
* ACPI_HAS_DEVICE_NVS does not exist anymore in ToT and hence it's
selection in broadwell is not required.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic31d7ae62c5df72708b724160e96e10b46002eb1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update SKU specific power limits for ADL-M as per document 643775.
BUG=None
BRANCH=None
Change-Id: I40b9b3a508c549d940e1c2c9e8b4079695b694e6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 66dbb0c5d6.
The numbers were meant for Cannon Lake, but the code was also meant
to be used for all other platforms using the Cannon Point PCH. Now
Cannon Lake support is even dropped, so we can cleanly revert to the
recommended values for the other platforms.
Change-Id: Iea56c6a29ca4b34c9852393fed2e3be4de128ec6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56662
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to received feedback, FSP-T enables MMCONF at address
0xe0000000 with 256 busses. Sanity-check that Kconfig matches that.
Add MMCONF_BUS_NUMBER such that MCFG in ACPI will be correct.
Change-Id: I01309638a9f4ada71e5e3789db34892ed4abfa3b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch decouples the selection of eNEM feature enablement from SoC
to ensure the ADLRVP does the validation first prior enabling this
feature on OEM/ODM reference designs.
BUG=b:168820083
TEST=No changing is being observed in .config with and without this CL.
Change-Id: I709185159d9869501b1d8e8d00f6d25ec77838bf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set default PL4 values for various Alder Lake CPU SKUs as per
bug#191906315 comment#10.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board.
Change-Id: I53791badbec3c165d56f20ce0656dc15d63bab37
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56917
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I20bf1a87c7a9b343a86053692617c127a1a3250d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56955
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake SoC specific Kconfig that internally selects all eNEM
related Kconfig. CONFIG_ALDERLAKE_CAR_ENHANCED_NEM will get
autoselected if platform doesn't have INTEL_CAR_NEM Kconfig selected
explicitly.
BUG=b:168820083
TEST=Verified CONFIG_INTEL_CAR_NEM is still enable.
Change-Id: Ife1c7d2036cece4598275dfc26ed138fb46bd881
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56090
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake onwards IA SoC to select CAR_HAS_L3_PROTECTED_WAYS from SoC
Kconfig and here is modified flow as below:
Add new MSR 0xc85 IA32_L3_PROTECTED_WAYS
Update eNEM init flow:
- Set MSR 0xC85 L3_Protected_ways = (1 << data ways) - 1
Update eNEM teardown flow:
- Set MSR 0xC85 L3_Protected_ways = 0x00000
BUG=b:168820083
TEST=Verified filling up the entire cache with memcpy at the beginning
itself and then running the entire bootblock, verstage, debug FSP-M
without running into any issue. This proves that code caching and
eviction is working as expected in eNEM mode.
Change-Id: Idb5a9ec74c50bda371c30e13aeadbb4326887fd6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per TGL EDS doc:575681, two ways will be controlled with one bit
of SF QoS register(SF Mask#1/#2) hence, selects SF_MASK_2WAYS_PER_BIT
for TGL SoC.
Change-Id: Ibeef653e0c510b62880b10b3f9767664d89c9623
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
MSR IA_SF_QOS_INFO (0xc87) has been introduced since TGL and is used
to find out the NUM_SNOOP_FILTER_WAYS. Bit[5:0] of MSR 0xc87 indicates
the maximum number of bits that may be set in any of the SF MASK
register. Hence, this patch calculates SF way count using below logic:
Calculate SF masks 1:
1. Calculate SFWayCnt = (MSR 0xC87) & 0x3f
2. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. SFWayCnt = SFWayCnt / 2
3. Set SF_MASK_1 = ((1 << SFWayCnt) - 1) - SF_MASK_2
Change-Id: Ifd0b7e1a90cad4a4837adf6067fe8301dcd0a941
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per TGL EDS, two ways will be controlled with one bit of SF QoS
register hence, this patch introduces SF_MASK_2WAYS_PER_BIT Kconfig to
allow SoC users to select SF_MASK_2WAYS_PER_BIT to follow the EDS
recommendation.
Calculate SF masks 2:
1. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. data_ways = data_ways / 2
Also, program SF Mask#2 using below logic:
2. Set SF_MASK_2 = (1 << data_ways) - 1
Change-Id: I442bed75f13d26f357cfb32c54c5fe9efa4b474b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Hook up microcode from 3rdparty repo for:
- TGL-U: 06-8c-01 (CPUID signature: 0x806c1)
- TGL-R: 06-8c-02 (CPUID signature: 0x806c2)
Verified microcode blob was found in CBFS on system76/darp7 (TGL-U).
CBFS: Found 'cpu_microcode_blob.bin' @0x103c0 size 0x31c00 in mcache @0x76c2d0ac
microcode: sig=0x806c1 pf=0x80 revision=0x88
coreboot reports the correct revision for the microcode.
Change-Id: I210c0133dad7ade63b9f7177aaa9a69b019469af
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56862
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: Ia6485bde5b33af067dfb15ca410a164e288b76b2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I367554053f78b760ece6d59f79ce1f0e0f9fdfc6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I0580fb3ec9daafac273dcb091f48ce403c22e8f8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-clause and adjust comments.
This changes behavior since now related options are always set,
depending on if coreboot or the FSP should be responsible for the
chipset lockdown. This ensures a defined state independent from the
default configuration of the FSP.
Change-Id: I0c43a11a40a474de4af22aa5506b1d387809bda2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause and adjust comments.
Change-Id: I202c212ec8e9ac63f5512c2e74040c23e1562b9a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch updates the VccIn Aux Imon IccMax for ADL-P to SOC SKU
specific values from the FSP default value 160.
* ADL-P 682(45W) = 137.
* ADL-P 482(28W) = 128.
* ADL-P 282(15W) = 128.
These config values are generated iPDG application with ADL-P platform
package tool and supports 15W/28W/45W SKU's.
RDC Kit ID for the iPDG tools,
* Intel(R) Platform Design Studio Installer: 610905.
* Intel(R) Platform Design Studio - Platform ADL-P (Partial): 627345.
* Intel(R) Platform Design Studio - Platform ADL-P (Full): 630261.
BUG=b:195033556
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I6c159035cba781d3661a0a0cef16f9591a583912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56176
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds 4gb and 6gb dram density support to APL and GLK.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: Ic0d5d14f26a30da7a9caf4ef43d7fac88a4d2bf1
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55153
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Originally we use rank_density=0 to mean disable the channel, but actually
rank_density=0 means 4Gb density in the FSP.
This patch changes the LPDDR4 enum values to the real density number and
adds a switch statement to mapping the density define in the FSP.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: I36dba2cef130211e7aea9e2a4f82c5db78f82a83
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56805
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
TGL also introduces parameters for customizing the default SVID:SSID.
These must be set or it will still use the FSP defaults.
Tested by checking lspci output on System76 darp7 (TGL-U).
References:
- b1fa231d76 ("soc/intel/cnl: Allow setting PCIe subsystem IDs after FSP-S")
- TigerLake FSP Integration Guide
- Intel Document #631120-001
Change-Id: I391b9fd0dc9dda925c1c8fe52bff153fe044d73e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Make use of deterministic cache helper functions from Alder Lake
SoC code to print useful information during boot as below:
Cache: Level 3: Associativity = 12 Partitions = 1 Line Size=64 Sets=16384
Cache size = 12 MiB
Change-Id: I30a56266015d69abccb885b3f230689488ee0360
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is clearer when ACPI_DEVICE_SLEEP_D3_COLD is used instead of
the number 4.
Change-Id: I4b0ade1cd0b4b9cdb59f90f8d455269d0b69ed86
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
coreboot always assumes that BSP APIC ID will always be 0 but as
per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, it says that BSP can
be any processor whose index/APIC ID might not be 0.
To handle this situation, init_cpu call is required to modify to
handle dynamic detection of APIC ID from BSP instead of hardcoding
always through devicetree. Function has been updated to create
a new node with actual BSP APIC ID when devicetree doesn't contain
APIC ID defined. In case APID ID is defined, function will use a
node with the APIC ID defined in devicetree.
Changes also requires to remove "lapic 0" hardcoding from devicetree
to allow code to fill BSP APIC ID dynamically. Otherwise coreboot
will create an extra node for CPU with APIC ID 0 and it'll show as a
extra node in kernel. This will cause kernel to report wrong (extra)
core count information then actually present.
BUG=None
BRANCH=None
TEST=Boot the JSL system and observe there is no functional impacts.
Without this CL kernel core count in `lscpu` = 3
With this CL, kernel core count is corrected to 2.
Change-Id: Ib14a5c31b3afb0d773284c684bd1994a78b94445
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This CL adds support for new ADL-M graphics Device ID 0x46aa.
TEST=boot to OS
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib24b494b0eedad447f3b2a3d1d80c9941680c25d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move post_codes.h from include/console to
commonlib/include/commonlib/console.
This is because post_codes.h is needed by code from util/
(util/ code in different commit).
Also, it sorts the #include statements in the files that were
modified.
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: Ie48c4b1d01474237d007c47832613cf1d4a86ae1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56403
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sometimes it's preferable or even necessary (e.g. stability issues) to
limit the maximum package C state. Let's add a devicetree option that
keeps the current behavior if it is left unset.
Change-Id: I0dc254d34f46de4c65cb85cc92e4b7f26618888d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These values are quite important and our default tables sometimes have
holes. We should at least make it visible what the resulting settings
are.
Change-Id: Ic716d073da1c2638c4b16f2eac01b83a0768d22f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Values were taken from PDG (571391), 51.3 IMVP8 Voltage and Current
Requirements.
Change-Id: Iffa29386cb7da333353dafd0ba3a61ca61a0ccac
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Currently, the `USE_LEGACY_8254_TIMER` Kconfig option is the only way
to enable or disable the legacy 8254 timer. Add the `legacy_8254_timer`
CMOS option to allow enabling and disabling the 8254 timer without
having to rebuild and reflash coreboot. If options are not enabled or
the option is missing in cmos.layout, the Kconfig setting is used.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic82c7f25cdf6587de5c40f59441579cfc92ff2f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
