Enable Core Performance Boost feature in automatic mode.
Also enable C6 state which is a dependency for proper CPB operation.
CPB allows to raise single core frequency from 1000MHz to 1400MHz
during high load if other cores idle. The processor has additional
boosted P-states when CPB is enabled, but these are hidden from OS.
TEST: Higher single-core CPU performance is indicated by increased
memory bandwidth as reported by memtest86+.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5e080bfaee06fd13cedf5151d4a598ec212213f2
Reviewed-on: https://review.coreboot.org/c/31229
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These are defined for __SIMPLE_DEVICE__ when PCI
enumeration has not happened yet. These should not
really try to probe devices other than those on bus 0.
It's hard to track but there maybe cases of southbridge
being located on bus 2 and available for configuration, so
I rather leave the code unchanged. Just move these out of
arch/io.h because they cause build failures if one attempts
to include <arch/pci_ops.h> before <arch/io.h>.
There are two direct copies for ROMCC bootblocks to
avoid inlining them elsewhere.
Change-Id: Ida2919a5d83fe5ea89284ffbd8ead382e4312524
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
With PCI_DEV() always defined it is no longer
necessary to exclude this code from building.
Change-Id: I58a6348750d240aa6024599f7b1af1449f31e8ac
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Traditionally, we have always allocated 1 DRAM ID per part number.
However, on nami, we have run out of DRAM IDs because we have
supported so many different parts. We are now adopting the use of
generic SPD files that are feature-based rather than specific to each
part, allowing us to support multiple parts with a single SPD.
The common SPDs were created by taking current SPDs in Nami (which is
using the same DDR4 parts as Hatch) and zeroing out all the
manufacturer information and part names. Additionally, we zeroed out
bytes 128 (raw card extension, module nominal height), 129 (module
maximum thickness), and 130 (reference raw card used) after verifying
that they are not used in FSP. We verified with these fields zeroed
out, all nami devices could boot up without errors. We also verified
on the two Hatch skus that we have (4G 2400, 8G 2666) that the generic
SPDs boot properly.
BUG=b:122959294
BRANCH=None
TEST=Make sure that we can boot up on both 4G Samsung and 8G Hynix DDR4
devices that we currently have.
Change-Id: I14d9e6b13975b6a65b506e6cd475160711b8f6d4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of having SYSTEM_TYPE_DETACHABLE and SYSTEM_TYPE_TABLET use
PM_MOBILE have them use PM_TABLET instead.
Change-Id: If0ce51e522d36420ecd5b51bdfec6cca11c00333
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
df7aecd "cpu/intel: Configure IA32_FEATURE_CONTROL for alternative
SMRR" introduced a regression because it unconditionally writes to
IA32_FEATURE_CONTROL, which if it is already locked results in an
unhandled exception. The lock bit is already set on a system reboot.
Change-Id: I7d2df9e1b9d767809da7a61ccd877c6c40f132eb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31255
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Match devicetree what's present and in use.
Tested on wedge100s:
All PCI devices show up.
Change-Id: I669d059da1876ed669793db8c7eb1b96b481cb4c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/31228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Also includes lines sorted
Change-Id: Idf2b41f471f531b2a9c3e620563e3c658dea4729
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31267
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
"is_wakeup_source" flag is used to indicate if the concerned device can
trigger a wakeup. This flag is redundant with the "wake" GPE event
definition. So remove the redundant flag and use the "wake" GPE event to
mark the wakeup source.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS. Ensure that the device is marked as wakeup-source
in SSDT if wake GPE is configured. Ensure that the system can suspend
and the device acts as a wakeup source
Change-Id: I99237323639df1cb72e3a81bcfed869900a2eefa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`git grep iterface` shows that these are the only two occurrences.
Change-Id: I838a60c95c5d0fc3dee902f0b72761dd60c36221
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/31286
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
FSP-S is currently configuring GPIOs that it should not. This results
in issues where mainboard devices don't behave as expected e.g. host
unable to receive TPM interrupts as the pad for the interrupt is
re-configured as something else.
Until FSP-S is fixed, this change adds a workaround by reconfiguring
GPIOs after FSP-S is run.
All mainboards need to call cnl_configure_pads instead of
gpio_configure_pads so that SoC code can maintain a reference to the
GPIO table and use that to re-configure GPIOs after FSP-S is run.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I7787aa8f185f633627bcedc7f23504bf4a5250b4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current coreboot size is not adequate for adding new features.
Note for cros: This change is for merge to ToT only and should not be
cherry-picked into reef's firmware branch.
BUG=chromium:903833
TEST=emerge-reef coreboot
Change-Id: Ie7a25c4638c474e81fb34b57de0dfc1bf393ea67
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add maximum width and height options and set the default to 2560x1600
(WQXGA). The framebuffer will be scaled up to the displays' native
resolutions. So this should help with tiny fonts on high-DPI displays.
For laptops, reasonable defaults can be set at the mainboard level.
Change-Id: I47fba063629260c3a2854caf7a73f1a1e933d063
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We generate a $(obj)/cb-config.ads once and copy it per stage that uses
it to $(obj)/<stage>/cb-config.ads (to simplify the gnat-bind step). The
Ada package is called `CB.Config`. As there was no `CB` package yet, add
that too.
Change-Id: I963a6517ef4bcf84f2c8e9ae8d24a0d6b971d2b0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This moves a lot of the common romstage boilerplate code to a common
location, while adding a few mainboard specific hooks.
Another difference is that the settings for enable_igd and enable_peg
are now based on the static devicetree settings.
Change-Id: I30ef7f6962aabde78b5c40e0b53bb85e01c254c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some settings don't make sense like specifying input/output on native
ports or high/low on input ports.
Change-Id: Ib37837b9cdb8bb05e2523e0c43cc71fe4fbf243b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31187
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
his either sets unwanted or unnecessary settings.
Also this RCBA replay did not even originate from the T400 as this
code was copied from the Thinkpad x200 code on which this replay was
already removed in 7bcd062 'mb/lenovo/x200: Remove RCBA replay'
Change-Id: Iac6846d43395e342897e03c1ad31387638bcac64
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch ensures to select chromeos kconfig only for required
CFL-U and WHL-U RVPs supported by Intel client team.
TEST=Ensure CONFIG_GBB_FLAG_FORCE_MANUAL_RECOVERY is only selected
for CFL-U and WHL-U boards.
Change-Id: Ib61409402a948f8d5f91130e200c45320ea13d3d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31214
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add an ACPI device that is compatible with the Intel Virtual
Button kernel driver for reporting tablet mode state and various
virtual button events that may come from the EC.
This driver is used in Windows and in the Linux kernel at
drivers/platform/x86/intel-vbtn.c
Because of a check in the kernel driver it expects the board to
define the SMBIOS enclosure type as convertible for the check at
driver load time for tablet/laptop and dock/undock to work.
The virtual tablet mode button will proxy the tablet mode state
sent from the Sensor Hub to a SW_TABLET_MODE event in the kernel.
The virtual power button is used during S0ix for the EC to wake
the system with an SCI. There are separate press and release
events which are sent for completeness, although the kernel driver
will ignore the release event.
BUG=b:73137291
TEST=Test that the power button can wake the system from S0ix.
Also verify that the device is reported as laptop mode at boot.
Change-Id: I0d5dc985a3cfb1d01ff164c4e67f17e6b1cdd619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31208
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These are more common system types and in some cases it is important
to know when a device is a convertible or a tablet or detachable
instead of just a laptop.
This change will select the appropriate SMBIOS enclosure type based
on the selected system type.
This is important for the Intel Virtual Button driver as it does a
check on the SMBIOS enclosure type and only enables the tablet mode
events if it is set to convertible:
https://patchwork.kernel.org/patch/10236253/
Change-Id: I148ec2329a1dd38ad55c60ba277a514c66376fcc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
After CL:31122, we can finally define a memory type specific for BL31,
to make sure BL31 is not loaded on other reserved area.
Change-Id: Idbd9a7fe4b12af23de1519892936d8d88a000e2c
Signed-off-by: Ting Shen <phoenixshen@google.com>
Reviewed-on: https://review.coreboot.org/c/31123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The ACPI spec has an asl example for _PLD in the form:
Name (_PLD, Package (0x01) { ToPLD (PLD_Revision = 0x2) })
When I ported this to acpigen and diffed the results I noticed that
the binary blob was no longer provided within a package. The ACPI
spec (section 6.1.8 in version 6.2) defines _PLD as "a variable-length
Package containing a list of Buffers". This commit changes
acpigen_write_pld to use a package (the one existing caller I found
isn't wrapping the result in a package so it doesn't look like
it was intended for the callers of acpigen_write_pld to be responsible
for using a package.
BUG=none
BRANCH=none
TEST=Verified that after this change a package is use and the result
of acpigen matches what was used in the original asl.
Change-Id: Ie2db63c976100109bfe976553e52565fb2d2d9df
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
If an acpi_dp table has children but no properties then acpi_dp_write()
will write out a properties UUID and package that contains no properties.
The existing function will avoid writing out a UUID and empty package
when no children exist, but it seems to assume that properties will
always be used. With this change properties are handled in a manner
akin to children so that a UUID and package are only written if
properties exist.
BUG=none
BRANCH=none
TEST=Confirmed that prior to this change a UUID and empty package was
present for a device that had children but no properties. Verified that
after this change the UUID and empty package are no longer present but
the child UUID and package are still present.
Change-Id: I6f5597713a1e91ca26b409f36b3ff9eb90a010af
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The allocation is not required before romstage,
so it can be just another CAR_GLOBAL instead of
polluting the linker script.
Change-Id: I0738a655f6cc924fbed92ea630f85406e3f58c0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31191
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The default state of the HOSTSW_OWN register in the PCH is zero, which
configures GPIO pins for ACPI ownership. The board variabt GPIO tables
can request specific pins to be configured for GPIO driver ownership.
This change sets the HOSTSW_OWN ownership bit when requested and
explicitly clears the ownership bit if not requested.
BUG=b:120884290
BRANCH=none
TEST=Build coreboot on sarien. Verified UEFI to coreboot transition
boots successfully.
Change-Id: Ia82539dbbbc7cf5dfb9223902d563cafec1a73e5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
By APL BIOS Spec, we must not do this on warm boots.
The TODO comment seems stale and copied over. So the actual
requirements for SGX are unknown and we add a guard for that
case.
Change-Id: I09b4a2fe22267d7318951aac20a3ea566403492e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/31200
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reconfigures the GPP_D1 GPIO pin as a no-connect. It really
doesn't go anywhere today or on previous revs of the board.
BUG=b:110614620
BRANCH=none
TEST=atlas still boots
Change-Id: Iea53cf909f8f060c4e0f14e8b4ad579b838b7caa
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit 7696290004.
We're seeing trackpad problems on some units with the I2C bus running
at 1MHz but not at 400KHz. So, revert back to 400KHz until we
understand how to make 1MHz operation more robust.
BUG=b:123650686
Change-Id: Ifb06afece9eee0c153240d35e6c3001f5b74f310
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The default value for Chrome OS HWID should be different.
Calculated as HWID v1.
BUG=b:123336677
BRANCH=kukui
TEST=build and boots properly.
Change-Id: I39c640562c1c3b117292b8abacd36a4a9c2fa6c6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Use memory map from fw_cfg e820 map to find cbmem_top in romstage to
avoid conflicts with CMOS option table. Keep qemu_gwt_memory_size() as
fallback.
Change-Id: I6465085020125fc790257f09eb157030c6ceabcb
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Remove memory mapped copy of the file list to use it also in romstage.
fw_cfg_find_file searches directly for the file on data port.
Change-Id: Ie97ed3f0c98a5bb18a35ab0eaf8c4777a53e5779
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
These boards need a working VTD therefore enable this feature.
Change-Id: I74c64bf1bd66188c4c32b85c66683dafd0e1fd38
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The FSP has a parameter to enable or disable the VTD feature
(Intel's Virtualization Technology for Directed I/O). In current header
files for FSP-S (Apollo Lake and Gemini Lake) this parameter is set to
disabled per default. Therefore, if the FSP was not modified via BCT,
this feature is most likely disabled on all mainboards.
Add a chip parameter so that VTD can be enabled on mainboard level in
devicetree and therefore this feature can be activated if needed.
Change-Id: Ic0bfcf1719e1ccc678a932bf3d38c6dbce3556bc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31194
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables exporting the reset GPIO for CNVi Bluetooth module to
the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset
gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured
that the kernel btusb driver is able to find the exported GPIO in the
devices with CNVi BT module.
Change-Id: I10f28bfe705da5104d709ae2ed91a8ae003fa639
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GLK has a dedicated USB2 port that is used specifically for CNVi
BT. This requires that the ACPI tables define an additional USB 2 port
which results in _ADR for USB 3 ports being different for GLK than
APL.
This change splits the ports in xhci.asl into APL and GLK specific
ports.asl and selects the appropriate file based on
CONFIG_SOC_INTEL_GLK. It also adds support for returning HS09 for GLK
if ACPI name is requested for that port.
BUG=b:123670712
BRANCH=octopus
TEST=Verified that generated DSDT for octopus (GLK) includes HS09 and
for reef (APL) does not include HS09 definition.
Change-Id: I2d3d3690ec9ea1f6e35c38c3b3cbb82e961b7950
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31172
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This implementation adds support to create ACPI package for USB port
capability (_UPC) and physical location of device (_PLD) for USB2 port 10.
BUG🅱️123375275
TEST:Verify _UPC and _PLD ACPI packages gets published for USB2 Port 10
in SSDT and BT is functional in discrete and integrated mode.
Change-Id: Ifeab24505a700e8e4677be20074c7d0400769cec
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31197
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AGESA doesn't detect invalid NV data during AmdInitResume(). In
cases where the data has been erased, or cannot be found, reboot
the system. Otherwise the user will experience a hang when cbmem
isn't recovered and the postcar frame cannot be initialized.
BUG=b:122725586
TEST=Write S3 NV save data with 0xff and force reboot
Change-Id: Ib3cf2515f300decd3de198f7741660d95ee4c744
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add a separate ACPI device for the Wilco EC event interface so that the
OS drivers can bind to it separately. Since the event handling is all
done with ACPI and not mailbox calls this will be implemented as a
standard acpi_driver in the kernel.
BUG=b:119046283
TEST=veriy device exists in DSDT
Change-Id: I5259a926fb6d5faea835bcdefa12f0184c5adf4a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1) In the EC _REG method set the flag indicating S0ix support in the OS.
2) Add a function that can be called by the LPI _DSM method to indicate
to the EC that the OS is entering or exiting S0ix.
BUG=b:73137291
Change-Id: Iddc33a08542a6657694c47a9fda1b02dd39d89f7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31094
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable xHCI by default if USE_BLOBS option has not been selected.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I1c3f0ff49fbe3db3ef095d99055f75d65cd6f661
Reviewed-on: https://review.coreboot.org/c/31216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Register 0x2a [Bit 1] is a PIN89, PIN90 function select for i2c
Change-Id: I9231a68ec7e9a3130a6b6975544bf89ab09cb3e6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The structure is placed inside CBMEM, one should
use types with fixed size. Seems we prefer to
prepare for 64-bit builds even for MMIO pointers.
Change-Id: I60382664a53650b225abc1f77c87ed4e121d429e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
We need sizeof(struct ehci_dbg_info) of 88 but only
reserved 64 bytes. If usbdebug_hw_init() was called
late in romstage, for some builds it would corrupt
CAR_GLOBALs like console_inited variable and stop
logging anything.
Also change pointer initialisation such that
glob_dbg_info will hit garbage collection for
PRE_RAM stages.
Change-Id: Ib49fca781e55619179aa8888e2d859560e050876
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Also show hart id in trap information for easier debugging.
Change-Id: I20acf86e1af111600c158295ae03b2167838d127
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/31201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
1. Simplify payload code and convert it to C
2. Save the FDT pointer to HLS (hart-local storage).
3. Don't use mscratch to pass FDT pointer as it is used for exception handling.
Change-Id: I32bf2a99e07a65358a7f19b899259f0816eb45e8
Signed-off-by: Xiang Wang <wxjstz@126.com>
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/31179
Reviewed-by: ron minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It has 2x 10GbE XGMII and 1x i210IT on PCIe, but no GBE.
Change-Id: I641c336350a0b05f3db7603cc7f6281ff3b0c388
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/31198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch ensures to enable IFD GBE region only for required
CFL RVP8 and 11 supported by Intel IOTG team.
TEST=Ensure CONFIG_MAINBOARD_USES_IFD_GBE_REGION is not selected
for CFL-U and WHL-U boards
Change-Id: If3fcd23c32f9afd2004fb176c0324f089f2ee412
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Have the generated Chrome OS ACPI GPIO table provide the ACPI GPIO
pin number instead of the raw GPIO number when possible.
This is necessary if the OS uses a different numbering for GPIOs
that are reported in ACPI than the actual underlying GPIO number.
For example, if the SOC OS driver declares more pins in an ACPI GPIO
bank than there are actual pins in the hardware it will have gaps in
the number space.
This is a reworked version of 6217e9beff
which does not try to convert CROS_GPIO_VIRTUAL.
BUG=b:120686247
TEST=pass firmware_WriteProtect test on Sarien
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I3ad5099b7f2f871c7e516988f60a54eb2a75bef7
Reviewed-on: https://review.coreboot.org/c/31080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Datasheets describe the used command as 'I2C Read' but adding the
word 'eeprom' in between should avoid further confusion with other
block commands.
Followups will add a symmetrical pair of commands i2c_block_read()
and i2c_block_write() that operate via I2C_EN bit and have a 32
byte size restriction on block transfers. For some hardware revision
these block commands are available, while 'I2C Read' was not.
Change-Id: I4494ab2985afc7f737ddacc8d706a5d5395e35cf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Convert vboot_platform_prepare_reboot() to call a function in
soc//stoneyridge. A subsequent patch will add another call to
the new function, and this change removes any inference of a
dependency on vboot.
BUG=b:122725586
Change-Id: I634fcd030e206c790bda697a3dbef4e8cc21b3a8
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable USB ACPI driver for octopus boards and add bluetooth USB ACPI
configuration in devicetree. This change enables exporting the bluetooth
reset GPIO to the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS
Change-Id: Ie40f1ad70f21a6fd398ce23d060e0c588ba6ce41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
XHCI is currently named as XHC1. This leads to namespace lookup error in
the kernel when children USB ACPI devices are added under the scope of
XHCI device.
BUG=b:123296264
BRANCH=octopus
TEST=Boot to ChromeOS; Ensure that the below error is resolved in the
kernel dmesg
[ 0.001000] ACPI Error: [\_SB_.PCI0.XHCI.RHUB.HS03] Namespace lookup
failure, AE_NOT_FOUND (20170728/dswload-210)
Change-Id: Ia4921547fee6fb51333319b9e881501a7e75ebce
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add separate functions for selecting the port and reading the port.
Romstage can now read incremental from the data port.
Change-Id: I0ffde3bc2a4415a8af99af2275d16f6609099e37
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reduce the number of fw_find_file calls by returning the file structure
at fw_cfg_check_file. The file structure can then be used to allocate memory
and access the file content directly without recurrence searching.
Remove now unnecessary function fw_cfg_load_file.
Fixed breaking function calls and add include guard at fw_cfg_if.h.
Change-Id: I48cc943aaa999e4323e9d7e5dd666c5316533dcc
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
In payloads, we didn't set GPIO modes. We have to set up GPIO mode in
coreboot for payloads.
BUG=b:80501386
BRANCH=none
TEST=HW reboot works in depthcharge
Change-Id: Ibd2c6c071871edc59497fbb245cdbec6a814f621
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31148
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:31139 fixs few ACPI type error. Here is few more typo mistake.
Change-Id: Ieecf0ba8fe09ed5003d5ae766079b8f83cc891b9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31152
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move functions not available in PRE_RAM into seperate file.
Makes it easier to share code between rom and ramstage.
Change-Id: I0b9833fbf6742d110ee4bfc00cd650f219aebb2c
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/31141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently, selflock_check() verifies that the binary is loaded in an
usable RAM area.
Extend its functionality so we can also check that BL31 is loaded in
a manually reserved area, and fail early if the range is not protected.
Change-Id: Iecdeedd9e8da67f73ac47d2a82e85b306469a626
Signed-off-by: Ting Shen <phoenixshen@google.com>
Reviewed-on: https://review.coreboot.org/c/31122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Modifiy Makefile so that we can get board ID in verstage.
BRANCH=none
BUG=b:117916698
TEST=manually
Change-Id: Idcdb6e07f565c937185cab811abac0ce47e5e3a7
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Currently SMBUS registers are accessed through IO, but with stoneyridge
they can be accessed through MMIO. This reduces the time of execution by
a tiny amount (MMIO write is faster than IO write, though MMIO read is about
as fast as IO read) as most of the time consumed is actually transaction
time. Convert code to MMIO access.
BUG=b:117754784
TEST=Used IO to write and MMIO to read, to confirm a one to one relationship
between IO and MMIO. Then build and boot grunt.
Change-Id: Ibe1471d1d578611e7d666f70bc97de4c3b74d7f8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Because of Intel's faulty LPC clock, the SERIRQ mode must be corrected.
By removing this entry from devicetree, the default value (quiet mode)
is used. The problem is described in Intel document 334820-007 under
point APL47.
Change-Id: I7a45e0e5fcde17a20abd19a33282b8a9215b1480
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31138
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TPM chip is connected to the SPI interface of APL. The proper chip
select pin needs to be used in order to access the TPM in the memory
mapped space. This needed chip select is internally (inside APL)
routable to GPIO 106. Therefore the change of GPIO 106 mode is needed to
make the TPM work on SPI bus.
TEST=Build coreboot for mc_apl2 board and check the TPM console output.
In addition the TPM was correctly verified by our Linux driver.
Change-Id: I2b0d5a6f2c230187857c2428a70de61f21da6724
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Real unused GPIO pad is GPIO_123, but GPIO_122 is configured as unused pad.
This patch corrects the configuration.
BUG=NONE
BRANCH=octopus
TEST=emerge-octopus coreboot
Change-Id: I4473bd66a4162f5aee3b998aacba906824728fc8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake
the AP from suspend. Also create a task to initialize the hostevent
wake mask properly.
BUG=b:123325238,b:123325720
BRANCH=None
TEST=from AP console: powerd_dbus_suspend
from EC console: hostevent (make sure wake mask set)
from EC console: gpioset PCH_WAKE_L 0
Make sure device wakes up
Also, checked to make sure keyboard press wakes up
device from S3.
Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Unless things changed considerably, this file doesn't contain any
firmware. It is merely replacing a configuration EEPROM for the MAC
address etc. So don't call it firmware.
Change-Id: Ife6190639e7f05da2cb6eddeb1b0db0e8ffc8e6e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
List Raydium touchscreen in the devicetree so that the correct ACPI device
are created.
BUG=b:121105424
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
reflash the coreboot to DUT, make sure the Raydium touchscreen can work.
Change-Id: I9ffb2a858f31a8b003086806de07f4079870cddf
Signed-off-by: Hao He <hao.he@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31116
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL moves some initialization steps from bootblock to verstage. This
will save us about 2700 bytes (before compression) / 1024 bytes (after
LZ4 compression) in bootblock. In case of CONFIG_VBOOT is disabled,
these initialization steps will be done in romstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I9968d88c54283ef334d1ab975086d4adb3363bd6
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Now we have usb2eye configuration register in FSPUPD, so we need
to add an interface to override usb2eye setting.
BRANCH=octopus
BUG=NONE
TEST=Verified usb2eye custom setting works
Change-Id: I5c500964658072eaaf59364242aa928df25d99d1
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Asserting GPIO PERIPHERAL_EN8 will send a signal to EC to trigger a HW
reset for SoC and H1.
BUG=b:80501386
BRANCH=none
TEST=emerge-kukui coreboot; manually verified the do_board_reset() on
Kukui P1
Change-Id: I9afad84af2031a766bc08fc76c8b5f55588c453a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31118
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Separate WDT reset function from WDT driver, then we can use the common
WDT driver and have a board-specific reset function on different boards.
In Kukui, we plan to use GPIO HW reset, instead of WDT reset. Add config
"MISSING_BOARD_RESET" in Kukui to pass the build for now.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot;
Change-Id: Ica07fe3a027cd7e9eb6d10202c3ef3ed7bea00c2
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31121
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This board has almost the same schematics as [xt]60 so this should work.
See also commit 7971582e with Change-Id
Iff6dac5a5f61af49456bc6312e7a376def02ab00.
Change-Id: I8dc9b122eb64b5c1dcd0dbc99ac41aa0f8dd9766
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch removes stale ASL entries added in past due to chromeos
requirement.
BUG=115755982
TEST=Build and boot ICL platform without any problem.
Change-Id: I18b57822ce3198fb96aae977f0b552ff2d4a14ee
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31117
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SoC has an Image Processing Unit which is located on PCI 00:03.0.
There is a corresponding parameter for FSP which handles
enabling/disabling of this functionality (IpuEn). Add this device to
the disable_dev() function of the chip so that if this device is
disabled in devicetree the matching FSP parameter will be disabled as
well. As this parameter is only valid for Apollo Lake, use the config
switch CONFIG_SOC_INTEL_GLK to disable this code if compiled not for
Apollo Lake. As this issue is regarding a missing structure member,
this check needs to be done on preprocessor level and not at runtime.
Test=Verified this function on mc_apl2.
Change-Id: I75444bf483de32ba641f76ca50e9744fdce2e726
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
If the VTd feature is enabled, there will be up to two fixed resources
which are set up by the FSP. Add these resources to the list of system
resources so that the PCI enumerator will know them.
Change-Id: If96fc1c93746e3c7f510e5b3095ea3090e1b8807
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30991
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Generate DMAR table if VTd feature is enabled.
Test=Booted into Linux on mc_apl2 and verified the DMAR table contents.
In addition turned off Vtd and verified that no DMAR table is generated
at all.
Change-Id: Ie3683a2f3578c141c691b2268e32f27ba2e772fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In preparation of generating DMAR tables, provide the hook in SoC scope
for the systemagent to write ACPI tables. The complete functionality is
SoC-specific. Therefore the entry hook is defined as a weak function which
can be overridden by SoC code. If the SoC does not have support for
generating DMAR tables this hook will do no harm.
Change-Id: I1333ae2b79f1a855e6f3bb39bf534da170ddc9e1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is spotted using ./util/lint/kconfig_lint
To work around the issue, rename the prefix from `CONFIG_` to `CONF_`.
Change-Id: Ia31aed366bf768ab167ed5f8595bee8234aac46b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Select FSP_M_XIP if MAINBOARD_USES_FSP2_0, since all SkyKabylake
boards require FSP-M XIP when FSP 2.0 is used, and since not
having it selected results in a non-booting image.
Also, put select FSP_T_XIP if FSP_CAR in proper alphabetical order.
Change-Id: I6d3986eda18297b12490cefb236f5de5faca6550
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
In some cases (e.g. Arm architecture variants), include paths are stuck
into <stage>-generic-ccopts rather than CPPFLAGS_<stage> (in fact, the
whole redundancy between these two is kinda stupid and we should
probably eliminate the latter, but I don't want to get into that right
now). This patch makes sure those paths are also correctly translated
when invoking $(MAKE) for vboot.
Change-Id: I37f09b88e555567590664e0e6fac23c34fd887df
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Working:
- USB (Partially. Check "Not working")
- PCIe
- PCIe graphics
- All SATA ports
- Native memory init
- On-board audio (back and front)
- S3 (Sleep and wake)
Not working:
- Fan control
- USB (If the keyboard has a USB Hub or if the keyboard
is connected through 2 or more hubs then it doesn't
initialize in time. A simple reboot allows the
keyboard to be used in SeaBIOS and the bootloader)
Untested:
- PS/2
- On board graphics
Change-Id: I4ed2077248a8d7123c728c790d9b81fe37956ed2
Signed-off-by: Abhinav Hardikar <realdevmaster64@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30767
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ELAN touchpad supports up to 400KHz, so we need to limit its CLK
frequency to 400HKz.
BUG=b:123376618
BRANCH=octopus
TEST=built and verified touchpad I2C clk frequency gets be lower than 400KHz
Change-Id: If7a43fe20c7e5abdf23c8c36e34c072c371563bf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
While branded as thinkcentre a58 this board can also be found as
"L-IG41M".
Change-Id: I06ed424138c46c6b2f29f15c7ea5c3648b26a8d3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
MASK_STATUS disables interrupt status generation for the entire GPIO
controller when any debounce register is configured. This causes
problems when the kernel is loading drivers because we could lose
interrupts for previously loaded devices.
sb_program_gpios is also not setup to wait when configuring
PAD_DEBOUNCE, so there is a potential that we could lose the interrupt
status enable bit for other registers. By disabling MASK_STATUS we avoid
that problem.
BUG=b:113880780
BRANCH=none
TEST=Ran a reboot stress test that concluded that we are no longer
losing TPM interrupts while booting.
Change-Id: Ife1db3b1449f205092509595cbc3eca511bff57a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Also make soc_get_tss_table public and weak instead of static
in intelblock so it can be overridden in denverton.
Change-Id: Id9c7da474a81417a5cebd875023f7cd3d5a77796
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Intel RTC common code driver need to turn on RTC itself.After the
change, cannonlake and icelake platform will have RTC enabled.
BUG=b:123372643
TEST=build and boot up on sarien platform, check .config to see
CONFIG_RTC is set.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I0c8c5cf9e6f7f338b1f2f784c04254649d257536
Reviewed-on: https://review.coreboot.org/c/31112
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit dc666f5 (soc/intel/cannonlake: Change in SaGv options) added a
conditional preprocessor directive, but its condition was incorrect
because SOC_INTEL_CANNONLAKE is selected for CNL, CFL and WHL. Thus, an
explicit check for !SOC_INTEL_COFFEELAKE is required.
While we are at it, clean up the comment above a bit.
BUG=b:123184474
Change-Id: I8a6959bb615fb5668cbfe54339747d135bd5a005
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31095
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is spotted using "./util/lint/kconfig_lint"
While at it, do the check in C and not the preprocessor.
Change-Id: Icfda267936a23d9d14832116d67571f42f685906
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Upper 128bytes of CMOS and RCBA are already enabled at bootblock.
Tested on 945g-MA. Resuming from suspend is working fine
Change-Id: I3f34380b0e700cf60688ad58465f9cb0aeda0928
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31107
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Boots again to payload not found on qemu.
Change-Id: Ie107eb882cbaac5a5a06c1ff990e7b9364377640
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/30554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This board does not have PMH7.
Change-Id: I382958f012e5f4445efc76c7f36bbdf460c29be4
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31065
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Port the existing denverton tables to intelblock
- Add C-States table for denverton
Note: Removed code is functionally identical to corresponding
common code.
Tested-on: scaleway/tagada
Change-Id: Iee061a258a7b1cbf0a69bcfbf36ec2c623e84399
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
New emmc DLL values for Ampton
BUG=b:122307153
TEST=Boot to OS on 5 systems
Change-Id: Iadd58d254f4bb384f483c2c3e5615f7569d5211c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to allow the mainboard to configure the system before a
cr50 initiated update reset add a weak function that the mainboard
can override if necessary.
This will allow a board that would otherwise be configured to
stay off after an EC reset to instead power up after the reset and
not end up in a shut down state after a cr50 update.
BUG=b:121380403
TEST=update cr50 firmware on sarien and reboot
Change-Id: I11f9e8c9bfe810f69b4eaa2c633252c25004cbd0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31057
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Export the SOC level function to set the After G3 state so it
can be changed by the mainboard. The setting will be restored
by a normal boot but in some circumstances coreboot wants to
ensure that it will be powered up again after a reset.
BUG=b:121380403
TEST=update cr50 firmware on sarien and reboot and ensure the
host does not power off after the cr50 initiated reset.
Change-Id: I6cd572ac91229584b9907f87bb4b340963203c32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31056
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disabling CpuRatio UPD for FSP will ensure it does not force a
hard reset to set the CPU Flex Ratio at boot. This is important
in a recovery mode boot where the SOC will lose power and need
to set the flex ratio again.
Disabling SaGv makes recovery mode training faster and mirrors
the setting that was done on Skylake.
BUG=b:123305400
TEST=reliably enter recovery mode on sarien
Change-Id: Ie9664493a980af9acce82faff81f4c4b1355be73
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
It was observed system suspend/resume failure while running
RunInDozingStress. Apply correct GLK usb clock gating register
value to mitigate the failure.
BRANCH=octopus
BUG=b:120526309
TEST=Verified GLK clock gating register value after booting
to kernel.
Change-Id: I50fb16f5ab0e28e79f71c7f0f8e75ac8791c0747
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support Synaptics touch pad for Aleena/Kasumi.
BUG=b:122549449
BRANCH=master
TEST= Check if synaptics touch pad working in ChromeOS.
Change-Id: Icab1b312f1943b27037ef458044ce9e7172919ee
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31064
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The iGPU always needs access to its stolen memory. For proper IOMMU
support, we have to make the OS aware of that.
Directly below TOLUD lies the data stolen memory (BDSM) followed by
the GTT stolen memory (BGSM), the iGPU needs access to both.
Change-Id: I391d0a5f1ea14bc90fbacabce41dddfa12b5bb0d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Send required EC command to enable ACPI S3 wake up from lid switch.
BUG=b:120748824
TEST=Put Sarien system into S3 and then wake up from lid switch
successful.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I13f3469847b0886147b8b624311a1ece796f847b
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This reverts commit ab1227226e.
There were significant changes around soc_reset_tco_status() that this
code needs to be adapted to.
Change-Id: I563c9ddb3c7931c2b02f5c97a3be5e44fa873889
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/31071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
ARCH_RISCV_RV{32,64} will now select ARCH_RISCV.
Change-Id: Ia7a1a8f0bfab20e91b8429dd6dd3e9a4180a0a5b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Change-Id: If31e7102bf1b47c7ae94b86d981b762eda0a19e5
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25427
Reviewed-by: David Guckian
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ratio_max step is appearing twice when (ratio_max - ratio_min)
is evenly divisible by the ratio step.
This is because in this case there are no rounding down of ratio_max in
the for loop.
Thanks Jay Talbott for the step calculation algorithm.
Change-Id: I91090b4d87eb82b57055c24271d679d1cbb3b7a7
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
A programmable logic device used by Kontron as EC on their COM express
modules. The name `kempld` is taken from Linux kernel sources, as is the
I2C driver. The meaning of the acronym is unclear, probably: Kontron
Embedded Module PLD.
Change-Id: If9a0826c4a8f5c8cd573610c2d10561334258b36
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable gpio_keys driver for bobba and add required configuration in the
device tree to handle the pen eject event.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder.
Change-Id: I768b89d2b45f4dcab6d235b11ce00544a827f22d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently without any trigger the wakeup event is generated on both the
rising and falling edges of the GPIO input. Add support to specify the
trigger explicitly so that the configuration can be passed to the
kernel.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder and ejected from its holder.
Change-Id: Ifb08ba01106031aa2655c1ae2faab284926f1ceb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add new helper macros to enable configuring debounce duration for a
GPIO input. Also ensure that the debounce configuration is not masked
out.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the debounce
duration is configured as expected.
Change-Id: I4e3cd7744867bcfbaed7d3d96fed4e561afb2cec
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently all the helpers support configuring GPIO_DW0/1 registers. In
some architectures there is an additional configuration GPIO_DW2 register
that can be used to configure debounce duration etc. Add a helper macro
to enable configuring GPIO_DW2 pad register.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the current
configuration is not disturbed by turning on the GPIO_DEBUG option and
verifying the debug output before and after the change.
Change-Id: I3e5d259d007fdc83940a43cc4cd4a2b8a547d334
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's no such limit on 64 Bit coreboot builds.
* Fix comment in cbmem.h
* Remove 4 GiB limit on Cavium SoCs
Tested on opencellular/elgon.
Still boots Linux as payload.
Change-Id: I8c9c6a5ff81bee48311e8bf8e383d1a032ea3a6d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL adds a new function mt8183_early_init, which includes all
initializations that should be done in early stages. All mainboards
using MT8183 should manually call it in either bootblock or verstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I35d7ab875395da913b967ae1f7b72359be3e744a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Added new routine cr50_i2c_probe() which ensures that communication
with the Cr50 over I2C is good prior to attempting other initialization
of the Cr50 and TPM state. This avoids a race condition when the Cr50
is first booting that it may reset it's I2C slave interface during the
first few I2C transactions initiated from coreboot.
BUG=b:120009037
BRANCH=none
TEST=Run the Cr50 factory update against Careena board. Confirm that
I2C reads are retried until the DID VID is valid. Tested against debug
Cr50 firmware that forced failure of cr50_i2c_probe() and verfied that
coreboot shows recovery screen.
Change-Id: I47c59a32378ad00336277e111e81ba8d2d63e69a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
This patch enables relevant GPIOs to enable WWAN. WWAN also requires to
enable USB 2 port 6 and USB3 port 5 which is already enabled in device
tree related changes.
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I1559bbc6168aec1a369bf3291d2c1e2f9a2fbe07
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable PCIe WLAN for hatch
1. Enable PCI port 14 for PCIe WLAN
2. Enable CLKREQ, CLK SRC 3 for PCI port 14
3. GPIO pad config for WLAN and BT
USB port for BT has already been enabled so not included in this patch
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I4f2a6eb37a467ad8b8cdde8fe6b657fabb383b04
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
Tested on Intel DG41WV, the stage cache gets properly created and used
on S3 resume.
Change-Id: Ie46c1416f8042d5571339b36e1253c0cae0684b8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25606
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
Tested on Foxconn D41S.
Change-Id: I3d163e8ff328ba01425b524a673f34a96fb93ea7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25605
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
Tested on Lenovo thinkpad X200: on cold boot the external stage cache
gets created and the cached ramstage gets successfully used on the S3
resume path.
Change-Id: I642f7d6ae5523a35904c8e1f029027565a364d26
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25604
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
Tested on Intel D945GCLF and Lenovo Thinkpad X60, on cold boot the
external stage cache gets created and the stage cache gets properly
used on S3 resume.
Change-Id: I447815bb0acf5f8e53834b74785d496f9d4df1da
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25603
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some CPUs, (Intel core2 and pineview) have slightly different SMRR
MTRR mechanism. The MSR_SMRR_PHYSBASE/MASK MSRs are at a different
location, have slightly different semantics and need SMRR enable in a
locked down IA32_FEATURE_CONTROL MSR.
This change takes away the possibility to (not) lock
IA32_FEATURE_CONTROL on these CPUs, as this is needed for SMRR MSR to
work. Since sockets cover multiple CPUs of which only some support
SMRR, the Kconfig option CONFIG_SET_IA32_FC_LOCK_BIT is kept in place,
even though it gets meaningless on those CPUs. Locking that bit was
the default anyway.
With this patch Intel Netburst CPUs also configure
IA32_FEATURE_CONTROL. According to Intel 64 and IA-32 Architectures
Software Developer's Manual those CPUs support that MSR so issues are
not to be expected.
Change-Id: Ia85602e75385e24ebded75e6e6dd38ccc969a76b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27586
Tested-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
With the memory controller the separate sockets becomes a useless
distinction. They all used the same code anyway.
UNTESTED: This also updates autoport.
Change-Id: I044d434a5b8fca75db9eb193c7ffc60f3c78212b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31031
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setup to different block transactions are similar
enough to have common place to call execute_command()
in.
Change-Id: I671fed280f47e6bc673eb7506f09ed6ed36d2804
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26763
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds helper to test for SMBHSTSTAT flags for
hardware having finished or failed a transaction.
Change-Id: Idea15e03edde7aeedf198c1529f09c24a5bc0b06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/21120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Implement the common start of transaction.
Fixes a problem where smbus_wait_until_active()
can miss SMBHSTSTS_HOST_BUSY being set, if
transaction completes very fast. Or if we are
single-stepping or executing under SerialIce
emulation.
Change-Id: Icb27d7d6a1c54968950ca292dbae05415f97e461
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/21119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Implements the common parts of any SMBus transaction
with a stub to log and recover (TBD) from timeout
errors.
Bits in SMBHSTCTL register are no longer preserved
between transactions.
Change-Id: I7ce14d3e895c30d595a94ce29ce0dc8cf51eb453
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/21118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
* Enable COM1, COM2, PMC1 and PMC2
TODO: Look at additional configuration and EC space.
Tested on wedge100s. The serial works without CONFIG_CONSOLE_SERIAL.
Change-Id: Id139bf243c7e7ac3e51a0ddb19d2396452341e29
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Add support for the SuperIO part of IT8528E
* Based on the IT8528E datasheet and tests on vendor firmware
TODO: Add support for accessing EC space, which should be
implemented in src/ec/ instead, as it's a separate logical unit.
No datasheet is publicy available.
Tested on wedge100s.
The serial works under the OS without CONFIG_CONSOLE_SERIAL.
Change-Id: I72aa756e123d6f99d9ef4fe955c4b7f1be25d547
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Quick and ugly approach, just paste the file in place,
dropping any __PRE_RAM__ parts. That's the way it was
previously done for fam15tn already, refactoring common
parts will happen on a later date.
Change-Id: I29fd421fb4aef984d117912ac836dee71d3d73ea
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The two IO regions of the keyboard controller are 1 byte long, not 8.
Change-Id: I7319ce9f84181759f4dc7b59c0020f3a5dd5dc03
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/30958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Replace device name from B0D4 with TCPU for DPTF sensor. This
helps to maintain consistency between coreboot and UEFI BIOS.
Change-Id: I962d74fc1baa07581d065734aaabb4dcd5e3d247
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
RPFN is a R/WO register we write on it in i945/early_init.c and i82801gx/pcie.c
Drop the romstage write.
Change-Id: If9a131ad12530876a650b7a38daa9c9fc52aefb7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It is possible to configure debounce, but leave it disabled by specifying
a 0 value for the timeout. Add a define for allowing to do so via the
PAD_DEBOUNCE() macro.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=compile
Change-Id: I9de61297b0677cc904535a51c16970eecb52021d
Reviewed-on: https://review.coreboot.org/c/30998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable dptf functionality for IceLake based U and Y systems.
Change-Id: I8ef396f9df8e39300d5870fd9a147ecdd6f0ba90
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/29686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIO Termination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: I8156c67df152555ecf9e7be9e4851468538bcff1
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Kukui with vboot enabled will build with `detachable_ui`, which needs
larger space in CBFS for more complicated assets. So we need to revise
FMAP sections:
- BOOTBLOCK (not really used) only needs <= 32K.
- GBB can be much smaller since assets moved from GBB to CBFS.
- FMAP is re-ordered (with the cost of less efficient in bsearch) so CBFS can
get larger continuous space.
- COREBOOT(CBFS) should take all space left.
Since FMAP and COREBOOT have changed location, the system will need to
reflash EC (which contains the new bootblock) as well.
BUG=b:123202015
TEST=Builds and boots on Kukui P1
Change-Id: I22cff99dca8c396c5897c3f6631721af40f3ffbd
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
disable unused usb2 ports of bard and ekko skus
BUG=120874946
TEST=build a test firmware and run lsusb to check usb ports
Change-Id: I2ef3cd17ada8b65c96bc80675650905949f235e1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30986
Reviewed-by: Vincent Wang <vwang@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove guards around CPU code on which all platforms use parallel MP
init code.
This removes the option to disable HT siblings.
Tested on Foxconn D41S.
Change-Id: I89f7d514d75fe933c3a8858da37004419189674b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25602
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use parallel MP init code to initialize all AP's.
Also remove guards around CPU code where all platforms now use
parallel MP init.
This also removes the code required on lapic init path for
model_6fx, model_1017x and model_f4x as all platforms now use the
parallel MP code.
Tested on Intel DG41WV, shaves off about 90ms on a quad core.
Change-Id: Id5a2729f5bf6b525abad577e63d7953ae6640921
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25601
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the parallel mp init path to initialize AP's. This should result
in a moderate speedup.
Tested on Intel D945GCLF (1 core 2 threads), still boots fine and is
26ms faster compared to lapic_cpu_init.
This removes the option to disable HT siblings.
Change-Id: I955551b99e9cbc397f99c2a6bd355c6070390bcb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This places the parallel mp ops up in the model_1067x dir and is
included from other Intel core2 CPU dirs that can use the same code.
Tested on Thinkpad X200 on which boot time is reduced by ~35ms.
Change-Id: Iac416f671407246ee223075eee1aff511e612889
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/23434
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The 13v3 is just a 13v2 with TPM added, so duplicate 13v2 config
and change strings where needed. Leave MAINBOARD_PART_NUMBER unchanged
since boards were initially shipped with 13v2 firmware, and changing
it now would cause flashrom to throw a board mismatch error.
Change-Id: I1a5e4c84cc9444bb9731b6dcc4de2ce7427dbbb1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/31010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Adjust default CBFS_SIZE to match that used in configs for building
Change-Id: Ibe1312560a923dcdefb8af52a721ab76c0b08a2e
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/31008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
close the FP module power in power off (s5)
BUG=122887366
BRANCH=Nami
TEST= build test firmware and measure the fp power enable pin
Change-Id: I80ddfbf1edf7c6435d263d5f5e0edb8b8701817d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30910
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Followup removes SIPI_VECTOR_IN_ROM and it seems reasonable
enough to force the alignment unconditionally to page size.
Reason for the conditionals is the alignment is not possible
with romcc bootblocks having total size less than 4 kiB.
Change-Id: I0ff2786f80a319ebb3215d4fd696cda3e15c3012
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30855
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New emmc DLL values for Meep.
BUG=b:122308271
TEST=Boot to OS on 13 Meep system
Change-Id: I4247114ed69ff3aa283f0f72d5531ad0f37309ad
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31021
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The BMC KCS interface must be advertised to the host OS in order
for automatic load of the ipmi module to work. Expose the KCS
interface via ACPI.
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac7
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/c/19822
Reviewed-by: Piotr Kubaj <pkubaj@anongoth.pl>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 3278f859c3dd97a6d6d885a91dfd33d44e95d58b.
Reason for revert:
It turns out all we want to set in RAM stage is GPIO's DEBOUNCE config,
not its SCI configuration.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Boot grunt, does not go to recovery screen
Change-Id: I500934f3e03e66c97873accd4a979a23d4509675
Reviewed-on: https://review.coreboot.org/c/30997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Fix regression after commits
4ad7f5b AGESA: Use pcidev_on_root()
33ff44c binaryPI: Use pcidev_on_root()
Previously used call dev_find_slot() returned
pointers to PCI device nodes that were actually
not present in the hardware at all. Register
reads would come back with invalid (0xff) values
and writes would be ignored.
After change to pcidev_on_root(), attempting to
do register operations with non-present PCI
hardware immediately halts with error
get_pbus: dev is NULL!
Change-Id: I785350c171a642207c5fab884a953d45a3bfe592
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds a few southbridge calls needed for parallel MP init.
Moves the smm_relocate() function to smm/gen1/smi.h, since that is
where this function is defined now.
Tested on Thinkpad X220, shaves off ~30ms on a 2 core, 4 threads CPU.
Change-Id: Ia1d547ed4a3cb6746a0222c3e54e94e5848b0dd7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25618
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel pineview has the same alternative SMRR MSR and
IA32_FEATURE_CONTROL enable bit as core2 CPUs so properly check for
that before enabling this feature.
This also exposes a function to fetch whether alternative SMRR MSR's
ought to be used.
Change-Id: Iccaabfa95b8dc4366b8e7e2c2a526081d4af0efa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30868
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit b82afce18a.
Reason for revert: This causes depthcharge to not boot due to TPM timeout errors. Because there is no wait after setting the debounce register, we lose data because the read-modify-write loses the interrupt status bit.
e.g., GPIO 5 sets debounce, without a wait. Then GPIO 9 has it's debounce set. Because the interrupt controller is masking the interrupt enable status bit, the read-modify-write for GPIO9 loses the interrupt enable status bit and it never gets set again. This causes the interrupt to never latch.
We should possibly make depthcharge set the interrupt enable status bit for latched GPIOs.
Change-Id: Idd7259b14b24c441529d64e173be9faec03f4fc8
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/30981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Add API that should be implemented by the boot media drivers
for write-protecting a subregion.
Change-Id: I4c9376e2c2c7a4852f13c65824c6cd64a1c6ac0a
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/28724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some SPI controllers support both READ and WRITE protection
add a variable to the protect API for the callers to specify
the kind of protection they want (Read/Write/Both).
Also, update the callers and protect API implementation.
BUG=None
BRANCH=None
TEST=test that the mrc cache is protected as expected on soraka.
Also tried if the read protection is applied correctly.
Change-Id: I093884c4768b08a378f21242ac82e430ac013d15
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/30559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some usb devices exhibit signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BUG=b:122671995
TEST=check "Disable Link Compliance Mode" bit of "SuperSpeed Port Link
control" register and usb operation successfully.
Change-Id: Ia2ae7e52391fadc8ed23b8b76c45d410757d22ec
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/30948
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add available thermal sensors information for CPU throttling action.
BRANCH=None
BUG=b:120058043
TEST=Built and tested on Arcada system
Change-Id: I748ca0ce43915c96d71e63fb03fc3d1a02adc56c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I4d15d5acf0e2044e5128ce809c282fbcb35f24f0
Reviewed-on: https://review.coreboot.org/c/30746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
ThinkPad X1 ( https://www.thinkwiki.org/wiki/Category:X1 ) is nearly a
clone of X220, with additional USB3 controller on pci-e (as i7 variant
of x220), and a powered ESATA port wired to ata4 (Linux' annotation).
Documentation added.
Tested:
- CPU i5-2520M
- Slotted DIMM 8GiB
- Camera
- Mini pci-e on wlan slot
- Msata on wwan slot
- On board SDHCI connected to pci-e
- USB3 controller connected to pci-e
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.9.110-3 within Debian GNU/Linux stable, loaded from
SeaBIOS, or Linux payload (Heads)
Not tested:
- Fingerprint reader on USB2
- Onboard USB2 interfaces (wlan slot, wwan slot)
Change-Id: Ibbc45f22c63b77ac95c188db825d0d7e2b03d2d1
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With the i82801gx code automatically disabling devices ethernet
NICs attached to the southbridge PCIe ports can now be disabled
during the ramstage.
Change-Id: If4163f8101d37cc09c0b51b1be20bf8388ed2b89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30245
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The implementation is a simplified version of the haswell/broadwell
code. This also adds a chip option to enable coalescing from the
devicetree.
Change-Id: I6d7ddef96e4f45e163f7017175398a0938a18273
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The IO mask shouldn't contain zeros inside the block of ones.
Change-Id: Icfebbf1d1d88ceef58800339bf899931fdc61ab7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/30954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Sometimes, it’s not clear, what log level is configured (in Kconfig and
CMOS), so print the log level in the banner.
coreboot-4.9-354-gff6e99cebe Tue Jan 15 15:23:20 UTC 2019 bootblock starting (log level: 7)...
Change-Id: I82c87ae90cd53fd47458fc6df3ef2c7f238f0f3d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/30935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
```
if (!(a & (0xffff << 16))) {
^~
src/lib/libgcc.c:40:18: error: result of '255 << 24' requires 33 bits to represent, but 'int' only has 32 bits [-Werror=shift-overflow=]
if (!(a & (0xff << 24))) {
^~
src/lib/libgcc.c:45:17: error: result of '15 << 28' requires 33 bits to represent, but 'int' only has 32 bits [-Werror=shift-overflow=]
if (!(a & (0xf << 28))) {
^~
```
Change-Id: I7bdd75c20a76b303743d7e7e0d3a6503760284fd
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/23361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
set SaGv = SaGv_Enabled , To Enable System Agent dynamic frequency support
set HeciEnabled = 1, To Enable heci communication
set speed_shift_enable = 1 To Enable Speed Shift Technology support
Change-Id: Iea90a65a77ef5e45a802cfe6fd31e1921163b02b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
CNL,WHL and CFL all are not using midfixed option in SaGv so keeping it for
CNL only and removing it for others.
Change-Id: I754515c2f8e249479c603872c61ac9a006e962ff
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30917
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Change-Id: If336e9d7016987be151ab30d5c037ead3a998fe0
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Signed-off-by: Keith Short <keithshort@chromium.org>
Change-Id: Ie3ce519956f916023c8c52f1d11fa93331f52f3c
Reviewed-on: https://review.coreboot.org/c/30929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The address bits 19:0 of TSEG_LIMIT read as zero, but are ignored on
comparison. The result is that the limit is effectively FFFFFh.
Add one MiB to the register value to make TSEG 8MiB instead of 7MiB.
Fixes a crash related to SMRR not matching the TSEG region.
Change-Id: I1a625f7bb53a3e90d3cbc0ce16021892861367d8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
RISCV parts can be created with any one of four CPU modes enabled,
with or without PMP, and with either 32 or 64 bit XLEN.
In anticipation of parts to come, create the Kconfig variables for these
architecture attributes.
Change-Id: I32ee51b2a469c7684a2f1b477bdac040e972e253
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30348
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change tcc offset from 15 to 3 for sarien.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: I1c5d144e92d1e6e9c81b3e6686805ccf744b7203
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30808
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to EDS #565870 chapter 5.3.1, AG3E bit in PMC located in PMC
memory mapped register but not pci config spaces. Change the programming
to affect that difference.
BUG=b:122425492
TEST=Change System Power State after failure to "s5 off", and boot up
onto sarien platform, check the register with iotools mmio_read32
0xfe001020 and bit 0 is set.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I0934894558fd9cbc056dea8e7ac30426c2529e4e
Reviewed-on: https://review.coreboot.org/c/30945
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Michał Żygowski