This reverts commit aef0d6b0a7.
This commit can only pass far-end USB eye diagram but will fail on
near-end. Confirmed with Intel we should revert it.
Change-Id: I2eb1d5ddb05ca6bbf6512edf48e3e0d8396ce6a7
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/25651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
On glk there's a 4MiB L2 cache all the time. Take advantage of that
by initializing a 1MiB cache-as-ram area.
BUG=b:72728953
Change-Id: Ia4e777a13607d8b70c05534b0a172f0ec6b04c51
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25645
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The pch_smbus_init() function contains code to enable clock gating for
the SMBus controller. Unfortunately this code is buggy and leads to a
hanging system with the latest microcode version.
The hang occurs as follows:
The clock gate register is mapped into RCBA space. After reading the
RCBA address from the LPC device config space no mask is applied to the
value (only bits 31..14 are valid while bit 0 is the enable bit). For
this reason the final address is off by one. The old microcodes at least
allowed this unaligned access to the RCBA space. With the latest
microcode this access leads to CPU hang.
Once this is fixed the next issue occurs: After setting the clock
gating bit for SMBus (bit 5) the SMBus controller disappears from the
PCI bus completely and hence no usage of it is possible anymore.
To fix this issue the clock gating code is completely removed as it was
intentionally meant to enable clock gating on the SMB_CLK line and not
the clock gating on the PCIe interface of the SMBus controller.
This issue is known already and was discussed on the mailinglist:
[coreboot] BDX-DE PCI init fail
https://mail.coreboot.org/pipermail/coreboot/2018-January/085908.html
TEST=Boot mc_bdx1 with microcode version M1050663_07000012.
Change-Id: Icb86f4516f8a6e72552a44618737e682b0fdef33
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/25652
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Required for other ACPI generators, like the one used for _ROM.
* Add ACPI code for PEG10/PEG11/PEG12/PEG60 and include it on all platforms.
* Add PCIe driver for PEG. The driver returns ACPI names for ssdt generators.
Needs test on real hardware.
Change-Id: I96835c43522580c95fd4f250c56bf9438e993bc1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22337
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Turn on keyboard backlight in romstage to indicate that the system is
booting.
BUG=b:77921345
TEST=Boot grunt, keyboard backlight comes on.
Change-Id: Ib215b19ebdee2f8c4f431af775905eca42436d1c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25636
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There wasn't previously a way for Stoney platforms to run mainboard
specific code in romstage. This adds an early call for configuration
and passes along whether the system is currently resuming from S3.
BUG=b:77921345
TEST=Build, verify that weak function implementation gets called.
Change-Id: Id94855e1084814ec37956e603cd093d70f01a559
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Due to an accuracy issue on IMON in the IDT PMIC, the reported system
power consumption was higher than the actual consumption. To prevent
this problem, a logic must be implemented in mainboard_init(). This logic
consists of slope and offset as constants for Vcc and Vnn, which need
to be programmed by coreboot. This fix compensates for the accuracy
issue.
Change-Id: I77faf95951d03ac6ce97a6721dba6e8466122a25
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This reverts commit 70ba1b7e78.
This commit can only pass far-end USB eye diagram but will fail on near-end.
Confirmed with Intel we should revert it.
Change-Id: I6de44d5240393409d9ec5835a9de0c23453300f7
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25630
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI interrupt routing file routing.asl is not reflecting AGESA settings to
the NB Interrupt Routing Registers. The AGESA settings are:
Device self INTA INTB INTC INTD
GPP 0 23 0 1 2 3
GPP 1 24 8 9 10 11
GPP 2 25 16 17 18 19
GPP 3 26 24 25 26 27
GPP 4 23 3 0 1 2
HDA none 22 23 20 21
GBIF none 6 7 4 5
Fix the routing table, considering that NB IOAPIC starts at interrupt 24.
BUG=b:74104946
TEST=Build and boot to a modified grunt board to enable the emmc. Then used
"cat /proc/interrupts" to get active interrupts. Also checked IOAPIC
redirection registers, which are now being programmed.
Change-Id: I60847c46f3f938f9e97d7b323b27d20e36aa2d02
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update libgfxinit to current master. Changes include:
* a fix to decode the size stolen memory correctly on pre-SandyBridge
hardware,
* a PCI id based generation check, obsoleting the old check based
on PCH audio ids,
* some minor improvements around rarely used DDI ports (D and E), and
* added support for tiled and rotated framebuffers on Skylake+ hardware
(less interesting for coreboot, I guess?).
TEST=Booted kontron/ktqm77 (Ivy Bridge) and pending kontron/bsl6
(Skylake) both with text and linear framebuffers and observed
FILO's prompt showing up.
Change-Id: I9a3c35c60b9edf8775f3a489df7577092910e127
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/25453
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 06e3e1f055.
This commit can only pass far-end USB eye diagram but will fail on near-end.
Confirmed with Intel we should revert it.
Change-Id: Ie987061e27996b0acc8345bf9aadb42d2c940808
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25629
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This makes the Kconfig file more informative to read.
Change-Id: Icdf4184c8db9cfed4863d9e9f3b714d67f44a4bd
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
dimm_info.serial had a strange contract. The SPD spec defines a 4 byte
serial number. dimm_info.serial required a 4 character ascii string with
a null terminator.
This change makes the serial field so it matches the SPD spec.
smbios.c will then translate the byte array into hex and set it on the
smbios table.
There were only two callers that set the serial number:
* haswell/raminit.c: already does a memcpy(serial, spd->serial, 4), so
it already matches the new contract.
* amd_late_init.c: Previously copied the last 4 characters. Requires
decoding the serial number into a byte array.
google/cyan/spd/spd.c: This could be updated to pass the serial number,
but it uses a hard coded spd.bin.
Testing this on grunt, dmidecode now shows the full serial number:
Serial Number: 00000000
BUG=b:65403853
TEST=tested on grunt
Change-Id: Ifc58ad9ea4cdd2abe06a170a39b1f32680e7b299
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/25343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch enables EC SMI when ESPI is enabled.
BUG=b:77857802
TEST= SMI is working in depthcharge.
Change-Id: I52726194b8346488e5ad781e78e33c5d286d132f
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25569
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The converter was setting SMBIOS values when dimm_info expects SPD
values.
dmidecode now shows the following:
Memory Device
Array Handle: 0x0000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 8192 MB
Form Factor: SODIMM
Set: None
Locator: Channel-0-DIMM-0
Bank Locator: BANK 0
Type: DDR4
Type Detail: Synchronous
Speed: 933 MT/s
Manufacturer: Hynix/Hyundai
Serial Number: 00000000
Asset Tag: Not Specified
Part Number: HMAA51S6AMR6N-UH
Rank: 1
Configured Clock Speed: 933 MT/s
Minimum Voltage: Unknown
Maximum Voltage: Unknown
Configured Voltage: Unknown
Example debug output:
AGESA TYPE 17 DMI INFO:
Handle: 1
TotalWidth: 64
DataWidth: 64
MemorySize: 8192
DeviceSet: 0
Speed: 1200
ManufacturerIdCode: 44416
Attributes: 1
ExtSize: 0
ConfigSpeed: 933
MemoryType: 0x1a
FormFactor: 0xd
DeviceLocator: DIMM 0
BankLocator: CHANNEL A
SerialNumber(8): ' 00000000'
PartNumber(20): 'HMAA51S6AMR6N-UH '
CBMEM_ID_MEMINFO:
dimm_size: 8192
ddr_type: 0x1a
ddr_frequency: 933
rank_per_dimm: 1
channel_num: 0
dimm_num: 0
bank_locator: 0
mod_id: 44416
mod_type: 0x4
bus_width: 3
serial: 0x00000000
module_part_number(18): 'HMAA51S6AMR6N-UH '
The serial number we get from AGESA (at least on my
board) is always 00000000. I'm assuming this is because the SPD info is
compiled in.
`mosys memory spd print all` is still failing though. I will look into
that next.
BUG=b:65403853
BRANCH=dimm-info
TEST=Test output above
Change-Id: I076bc3f965f81a9374c8976da48c7fdce014dc0c
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/25304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a new method to clone an existing memrange with all of its entries.
Required for new bootmem type LB_MEM_RAM_DONT_OVERLAP.
Change-Id: I64b27bf2611ca310385ef680f030a3e4aa0c2680
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25582
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the recovery cache to speed up recovery flows. Also
enable clearing of the normal mrc cache on recovery forced retrains.
BUG=b:77871444
TEST=went into recovery twice. 2nd time it boots faster.
Change-Id: Idfce42ac835637fa521545fadfedecd65df91d4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AMD AGESA returns DIMM info in SMBIOS format. dimm_info expects the data
in SPD format. These methods will be used to update amd_late_init.c so
it sets the correct values.
BUG=b:65403853
TEST=Built and booted grunt. Methods are not called in this commit. So
they were tested with the later commit by verifying the output of
dmidecode.
Change-Id: Id9fa98e9aad83dfd0a86f45e18b3c312665dce9b
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/25412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
For cannonlake_rvp, want to support two sound configurations based on
relevant daughter board connected (either of these configurations:
SND_MAX98373_NHLT and SND_MAX98357_DA7219_NHLT).
By default SSDT included all codec entries.
This patch corrects and includes relevant codec entries in SSDT
BUG=None
BRANCH=master
TEST=Verify 'emerge-cnlrvp coreboot' compiles successfully.
Change-Id: I4f9487f3a81ef2d24315f75ec1d34bfab8560224
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/24918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
By storing the FSP-M DRAM configuration parameter in the hwinfo block,
one becomes more flexible in case of a change of the DRAM type.
The configuration data from hwinfo block is a one-to-one representation
of the FSPM_UPD data starting with parameter 'Package' (offset 0x4d) and
ending before parameter 'Ch0_Bit_swizzling' (offset 0x88).
Change-Id: I58c1df0954a436710ecb59487ece07a0832b0de6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Relocate setting the temp range MTRR, for the SPI flash device, to
after completion of mp_init. The mp_init functionality mirrors the
BSP's exact MTRR settings into the AP cores. The ranges need to be
the correct calculated values and not some temporary setting.
This solves an MTRR sync issue on APUs with more than two cores,
i.e. more than a single compute-unit. MTRRs within a CU are shared
so the AP always stays in sync.
BUG=b:77457944
TEST=run on Kahlee
Change-Id: Idc4cccdf721e252bc87d6cba62a3406a9f19b940
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
To avoid rounding errors with the current data types, the formula in
this function must be converted.
Change-Id: I75d05165fd9e5a0992330df00f8665a05d2daeb3
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/25584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Grunt supports a keyboard backlight, so enable the ASL code.
BUG=b:77455525
Test=Boot Grunt, verify that the string 'KBLT' is in the DSDT.
Change-Id: Idf0f23581bcba0b035c126c68fb167274d7c698a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25470
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 5fbe788bae.
This commit was submitted without its parent being submitted,
resulting in coreboot not building.
Change-Id: I87497093ccf6909b88e3a40d5f472afeb7f2c552
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/25616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds a few southbridge calls needed for parallel MP init.
Moves the smm_relocate() function to smm/gen1/smi.h, since that is
where this function is defined now.
Tested on Thinkpad X220, shaves of ~30ms on a 2 core, 4 threads CPU.
Change-Id: Iacd7bfedfccbc09057e1b7ca3bd03d44a888871d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23432
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is required for clock parameter settings to take effect.
BUG=b:75306520
BRANCH=None
TEST=On Octopus, used a scope to check that spi_clk fed to tpm is
1 MHz
Change-Id: Icdb617aa4aa944d46b3a56dab88d2008b01dea0d
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The term MTRR has been misspelled in a few places.
Change-Id: I3e3c11f80de331fa45ae89779f2b8a74a0097c74
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The missing space resulted in the following broken output:
> ERROR: Not enough MTRRs available! MTRR indexis 10 with 10 MTTRs in
total.
Put the string on one line to make it obvious where the spaces should be
and to help users of grep.
Change-Id: Ib9e8109d88c1bf38e7dda3dbf1c8d47fb0d23265
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25567
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RISC-V does not have the kind of I/O space that x86 has. Other
architectures tend to leave out these definitions as well.
Change-Id: I7328dae1f1fa4ef8772750244a0b11a3fa5aa88f
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This allows VGA output in SeaBIOS to be enabled using the
SEABIOS_VGA_COREBOOT Kconfig option. Currently, it’s impossible to select
the VGA text frame buffer in the Kconfig menu.
I'm not sure why this wasn't enabled in the first place, but
SeaVGABIOS seems to work just fine with this patch.
Tested on KCMA-D8.
Change-Id: Ic924a12fbe89940b5f26d211eb8de6cab0be767a
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/25554
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel internal graphics preallocated memory size should be selected from
below lists as per Intel FSP UPD header:
0x00:0MB, 0x01:32MB, 0x02:64MB, 0x03:96MB, 0x04:128MB, 0x05:160MB,
0xF0:4MB, 0xF1:8MB, 0xF2:12MB, 0xF3:16MB, 0xF4:20MB, 0xF5:24MB,
0xF6:28MB, 0xF7:32MB, 0xF8:36MB, 0xF9:40MB, 0xFA:44MB, 0xFB:48MB,
0xFC:52MB, 0xFD:56MB, 0xFE:60MB
This patch ensures that coreboot can report the same preallocated
memory range for intel grapics during memory layout calculation.
Note: Today all existing SoCs(except Cannonlake) are supported under intel
common code block design may not need to use any other values than 0x0-0x05
for GFX DSM range. DSM memory ranges between 0xF0-0xF6 are majorly for
early SoC samples and validation requirement. This code block to justify
all differnet possible ranges that FSP may support for a platform.
TEST=Set IgdDvmt50PreAlloc UPD with different ranges between 4MB-60MB
and coreboot could able to calculate GFX DSM range accordingly.
Change-Id: I99735e9a2ee57626bd9d7258e700f7f39ef02e58
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On APL and GLK the i2c blocks use 133MHz input clock, but the
SPI blocks use a 100MHz input clock. Fix this so that the proper
target frequencies can be hit on the SPI controllers.
BUG=b:75306520
Change-Id: Iec36579894fa4633ac8d1035e6e7afec01af755f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Correct Cannonlake I2C clock frequency to 133Mhz that will match the
silicon, Cannonlake have I2C clock force to 133Mhz.
BUG=b:75306520
Change-Id: Iaab8851bb00cf27876d4068167a283ed79a28b2d
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25610
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Apparently Intel had decided to use different clock speeds for
some of its IP blocks in some of its designs. The i2c designware driver
has already been moved into common code allowing for its own Kconfig
value. That currently leaves SPI (UART isn't using the clock currently).
Therefore, remove SOC_INTEL_COMMON_LPSS_CLOCK_MHZ and add
SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ to allow for the different clock
speeds present in the system for the various IP blocks.
BUG=b:75306520
Change-Id: I6cb8c2de0ff446b6006bc37645fca64f2b70bf17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25608
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of moving AGESA calls from bootblock to romstage, create
infrastructure to pass a pointer to the AP cores, so they can jump directly
to romstage.
BUG=b:74236170
TEST=Build and boot grunt, actual test will be performed at a later patch.
Change-Id: If716d1c1970746f2ad90ef71ae9062c99f219897
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As part of moving AGESA calls from bootblock to romstage, callback function
AGESA_HALT_THIS_AP must be available at romstage.
BUG=b:74236170
TEST=Build and boot grunt, actual test will be performed at a later patch.
Change-Id: I0992b2de5856881c19191ec4f637168727686524
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25527
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of moving AGESA calls from bootblock to romstage, OemCustomize.c
of all boards using stoneyridge must be available at romstage.
BUG=b:74236170
TEST=Build grunt and kahlee, actual test will be performed at a later patch.
Change-Id: Ide9efdbff6a07c670034391c0d62e8b74fa5c02b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25528
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are two cameras on Nami and only one camera on Vayne.
We need to disable rear camera on all Vayne sku.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera shown on Vayne
Change-Id: I6e7c1e8791462f00ad8336372954ee0a9465d9b8
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
The code is mostly copied from src/cpu/intel/haswell.
TESTED on Thinkpad X220: on a cold boot the stage cache gets created
and on S3 the cached ramstage gets properly used.
Change-Id: Ifd8f939416b1712f6e5c74f544a5828745f8c2f2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that calc_var_mtrrs_with_hole() always chooses the optimal
allocation, there is no need for calc_var_mtrrs_without_hole()
any more. Drop it and all the logic to decide which one to call.
Tests performed compared to "upstream" (before "cpu/x86/mtrr:
Optimize hole carving strategy") on a Lenovo/X200s with 48MiB
GFX stolen memory.
2GiB total RAM: 3 MTRRs saved
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x000000007ac00000 size 0x7ab40000 type 6
0x000000007ac00000 - 0x00000000d0000000 size 0x55400000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
upstream:
MTRR: Removing WRCOMB type. WB/UC MTRR counts: 7/8 > 6.
MTRR: default type WB/UC MTRR counts: 4/7.
MTRR: WB selected as default type.
MTRR: 0 base 0x000000007ac00000 mask 0x0000000fffc00000 type 0
MTRR: 1 base 0x000000007b000000 mask 0x0000000fff000000 type 0
MTRR: 2 base 0x000000007c000000 mask 0x0000000ffc000000 type 0
MTRR: 3 base 0x0000000080000000 mask 0x0000000f80000000 type 0
patched:
MTRR: default type WB/UC MTRR counts: 7/5.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000000f80000000 type 6
MTRR: 1 base 0x000000007ac00000 mask 0x0000000fffc00000 type 0
MTRR: 2 base 0x000000007b000000 mask 0x0000000fff000000 type 0
MTRR: 3 base 0x000000007c000000 mask 0x0000000ffc000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000000ff0000000 type 1
4GiB total RAM: no MTRRs saved but slightly more accurate alignment
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x000000007cc00000 size 0x7cb40000 type 6
0x000000007cc00000 - 0x00000000d0000000 size 0x53400000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000017c000000 size 0x7c000000 type 6
upstream:
MTRR: default type WB/UC MTRR counts: 7/6.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000000f80000000 type 6
MTRR: 1 base 0x000000007cc00000 mask 0x0000000fffc00000 type 0
MTRR: 2 base 0x000000007d000000 mask 0x0000000fff000000 type 0
MTRR: 3 base 0x000000007e000000 mask 0x0000000ffe000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000000ff0000000 type 1
MTRR: 5 base 0x0000000100000000 mask 0x0000000f00000000 type 6
patched:
MTRR: default type WB/UC MTRR counts: 7/6.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000000f80000000 type 6
MTRR: 1 base 0x000000007cc00000 mask 0x0000000fffc00000 type 0
MTRR: 2 base 0x000000007d000000 mask 0x0000000fff000000 type 0
MTRR: 3 base 0x000000007e000000 mask 0x0000000ffe000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000000ff0000000 type 1
MTRR: 5 base 0x0000000100000000 mask 0x0000000f80000000 type 6
8GiB total RAM: possible savings but WB still beats UC
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x000000007cc00000 size 0x7cb40000 type 6
0x000000007cc00000 - 0x00000000d0000000 size 0x53400000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000027c000000 size 0x17c000000 type 6
upstream:
MTRR: Removing WRCOMB type. WB/UC MTRR counts: 7/11 > 6.
MTRR: default type WB/UC MTRR counts: 4/10.
MTRR: WB selected as default type.
MTRR: 0 base 0x000000007cc00000 mask 0x0000000fffc00000 type 0
MTRR: 1 base 0x000000007d000000 mask 0x0000000fff000000 type 0
MTRR: 2 base 0x000000007e000000 mask 0x0000000ffe000000 type 0
MTRR: 3 base 0x0000000080000000 mask 0x0000000f80000000 type 0
patched:
MTRR: Removing WRCOMB type. WB/UC MTRR counts: 7/7 > 6.
MTRR: default type WB/UC MTRR counts: 4/6.
MTRR: WB selected as default type.
MTRR: 0 base 0x000000007cc00000 mask 0x0000000fffc00000 type 0
MTRR: 1 base 0x000000007d000000 mask 0x0000000fff000000 type 0
MTRR: 2 base 0x000000007e000000 mask 0x0000000ffe000000 type 0
MTRR: 3 base 0x0000000080000000 mask 0x0000000f80000000 type 0
Change-Id: Iedf7dfad61d6baac91973062e2688ad866f05afd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For WB ranges with unaligned end, we try to align the range up and
carve a hole out of it which might reduce MTRR usage. Instead of
trying an arbitrary alignment, we try all and choose an optimal
one.
Also, restructure the cases when we try to find a hole. Which leads
us to the following three:
1. WB range is last in address space:
Aligning up, up to the next power of 2, may gain us something.
2. The next range is of type UC:
We may align up, up to the _end_ of the next range. If there
is a gap between the current and the next range, it would
have been covered by the default type UC anyway.
3. The next range is not of type UC:
We may align up, up to the _base_ of the next range. This is
the end of the gap, if there is one.
Change-Id: Iefb064ce8c4f293490a19dd46054b966c63bde44
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets the wake for EC to proper gpios.
BUG=77605178
TEST=Test that lidopen wakes up the system from S3.
Change-Id: Icbf30007403191005396027e74b9b6fb7319e006
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25539
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MONITOR/MWAIT had an irremediable hardware bug for Apollolake.
This has been fixed for GLK. Therefore, make MONITOR/MWAIT based
C-states the default for GLK and disable IO-Redirection based
C-states used for Apollolake.
Tested on GLK w/kernel 4.14.27 using turbostat to observe C-state
residencies with and without load.
Tested for S0ix entry and exit using:
"echo freeze > /sys/power/state" and "suspend_stress_test -c 500".
BUG=b:77639897
Change-Id: If648c25a9b26c04b278dce4af241d439790288ca
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/19718
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No longer needed as low memory backup is implemented as part of
the ramstage loader, when the actual requirement of the ramstage
to load is known.
Change-Id: I5f5ad94bae2afef915927b9737c79431b6f75f22
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15477
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adapt implementation from skylake to prepare for removal of HIGH_MEMORY_SAVE
and moving on to RELOCATABLE_RAMSTAGE. With the change, CBMEM and SMM regions
are set to WRBACK with MTRRs and romstage ram stack is moved to CBMEM.
Change-Id: I84f6fa6f37a7348b2d4ad9f08a18bebe4b1e34e2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fix the error below.
```
src/lib/lzmadecode.c: In function 'LzmaDecode':
src/lib/lzmadecode.c:77:2: error: macro expands to multiple statements \
[-Werror=multistatement-macros]
Range -= bound; \
^~~~~
src/lib/lzmadecode.c:300:7: note: in expansion of macro 'UpdateBit1'
UpdateBit1(prob);
^~~~~~~~~~
src/lib/lzmadecode.c:299:8: note: some parts of macro expansion are not \
guarded by this 'else' clause
} else
^~~~
cc1: all warnings being treated as errors
```
The macro is defined as below.
#define UpdateBit1(p) \
Range -= bound; \
Code -= bound; \
*(p) -= (*(p)) >> kNumMoveBits
Found-by: gcc-8 (Debian 8-20180402-1) 8.0.1 20180402 (experimental) [trunk revision 259004]
Fixes: 35af5c47 (src/lib: Fix spacing)
Change-Id: Ife0688541e23c05e26e429a6d8caee7e2d425b1b
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/25549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use standard coreboot function to set virtual wire mode on
the GNB IOAPIC.
BUG=b:74104946
TEST=Check GNB IOAPIC debug output on serial.
Change-Id: I4ff8698419890df1459b1107f0861cf8277a99b0
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
DDR2 DIMMs are uniquely defined by SPD byte 64 till 72 and 93 till
98. Compute a crc16 over that data to provide a solid way to check
DIMM identify.
Reuse the crc16 function from ddr3.c to do this.
Change-Id: I3c0c42786197f9b4eb3e42261c10ff5e4266120f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Change EN/DISABLED to INT_EN/DISABLED to avoid collision with other
EN/DISABLE definition.
Change-Id: I85b1c544d0f31340a09e18f4b36c1942ea0fa6ef
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25540
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move flush_l1d_l2 function to common location within the SoC.
BUG=None:
BRANCH=None
TEST= Build for glkrvp.
Change-Id: I4aaaaccc4f343bc4926111258a33e09e79c76141
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/25547
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds basic support for reading flags from GBB header
located in "GBB" section on SPI flash.
Change-Id: I35ecb5ba964511379baa4e9f458ba2e8c6b74b4e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's a standard function.
Change-Id: I039cce2dfc4e168804eb7d12b76a29af712ac7a1
Signed-off-by: David Hendricks <dhendricks@fb.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/23616
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested with GRUB 2.02 as a payload, booting Debian GNU/Linux 9.3 with
kernel 4.9. This code is based on the output of autoport.
Working:
- S3 suspend/resume
- USB
- Gigabit Ethernet
- integrated graphics
- PCIe
- SATA
- eSATA
- PS/2 port (only a mouse has been tested)
- hardware monitor
- onboard audio
- front panel audio
- native raminit (2 x 4GB + 2 x 8GB, DDR3-1333)
- native graphics init with libgfxinit
- EHCI debug. The debug port is the port closest to the HDMI port.
- flashrom, using the internal programmer. Tested with coreboot,
untested with the vendor firmware.
- NVRAM settings. Only `gfx_uma_size` and `debug_level` have been
tested with values different from the default.
Untested:
- VGA BIOS for graphics init
- PCIe graphics
- S/PDIF audio
Not working:
- "clear CMOS" button
The CPUTIN sensor on the Super I/O is not connected. The PECI agent is
likely connected instead to give CPU temperature readings. However,
there does not appear to be enough information in the publicly available
datasheets to fully set up the PECI agent. As a result, there is
currently no accurate, automatic fan control via the Super I/O.
Change-Id: I1fc7940bb139623a5a0fde984c023deca9b551f2
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/24971
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Broadwell-DE the FSP sets up DCACHE in the early call. The address
does not match the default FSP 1.0 address defined in
src/drivers/intel/fsp1_0/Kconfig which leads to errors when this range
is used in pre-ramstage stages.
This patch provides the matching DCACHE_RAM_BASE value among with a
suitable DCACHE_RAM_SIZE for the FSP based Broadwell-DE implementation.
The include order of Kconfig files makes sure that the Kconfig file in
the soc directory is sourced first and the defined values will override
the ones in src/drivers/intel/fsp1_0/Kconfig.
Change-Id: I2a55b576541a3d974ee2714b198095aa24fc46f5
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/25535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide ACPI path names for PCI domain and LPC device so that generated
ACPI tables have valid device paths.
Change-Id: I5a97e45ef50ec5ee9d64c5d2834968a02455cf72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/25534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some users have reported a successful boot with me_cleaner on Kaby Lake
with OEM firmware:
https://github.com/corna/me_cleaner/issues/3
It should work as well on coreboot.
Change-Id: Ifc47f19deee5c39ca27b427c9406da7f6e3e9f15
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/25507
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This imports common BDK sources that will be used in subsequent
patches.
The BDK is licensed under BSD and will be reduced in size and optimized to
compile under coreboot.
Change-Id: Icb32ee670d9fa9e5c10f9abb298cebf616fa67ad
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/25524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Instead of hard-coding a lot of default values of the framebuffer config,
we use the values provided by Display_Probing.Scan_Ports() and only
overwrite what is necessary. This way we are more independent from
changes inside libgfxinit.
Change-Id: I121bbd926532c27321446282aa334cc45cdbeef1
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/25452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Aligning the stride up to a multiple of 64 pixels was flawed: We want
to actually align up to one cacheline (64 bytes) as that's the mini-
mum what the hardware supports.
Change-Id: I3f824ffd7d12835935e4e4bde29fe82dc3e16f9d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/25451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
AgesaHeapRebase is an optional callout that allows AGESA to use a
coreboot-managed heap base address. Its internal default location
is determined by AMD_HEAP_START_ADDRESS which is defined as 4 MB.
Add a #define that AGESA may use once the feature is available.
BUG=b:74518368
Change-Id: Id23455779b1c8c4931ad1a3122587e09ad237ecc
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Replace an absolute value with a #define value in bootblock. This is
in preparation for using an additional MTRR in a subsequent patch.
Change-Id: I006c7cfa0057b3ed4a21359fc8367caf6ec5baf3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The FSP 2.0 needs to set the ac_loadline and dc_loadline for
each VR config. Without it, the Loadline is considered to be
0 mOhm and this causes CPU temp to jump all over the place
whenever the CPU is used.
This is necessary since there are no VR_CONFIG icc mappings for
Skylake SKUs, only KabyLake.
These values were copied from the Google Poppy devicetree.
Change-Id: I6aeb6ee521988b94f2ae94a60d1a28b87ba984d4
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Set the Thermal Control Circuit (TCC) activaction value to 95C
even though FSP integration guide says to set it to 100C for SKL-U
(offset at 0), because when the TCC activates at 100C, the CPU
will have already shut itself down from overheating protection.
This was tested on Purism Librem 13 v2. A bisect showed that the
immediate shutdowns happened after commit [1] was merged which led
to this solution.
[1] ec5a947b (soc/intel/skylake: make tcc_offset take effect)
Change-Id: Idfc001c8e46ed3b07b24150c961c4b9bc9b71a62
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Although VmxEnable is currently ignored by FSP, a forthcoming patch
explicitly enables it in coreboot, so set it in anticipation of that.
Enable Intel SpeedStep to ensure the ACPI tables are generated for
the C-states/P-states which are required for the xen-acpi-processor
module to be loaded. Without it, the Qubes 4.0-rc4 installer will
complain at boot about modules that could not be loaded.
Change-Id: I968ef36ec9382a10db13d96fd3a5c0fc904db387
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change the GPIO to match the TPM-enabled motherboards, and add TPM
support in devicetree and enable the config.
After changing the GPIO table, the librem 13v2 and librem 15v3 now
have the same GPIOs, so use a single gpio.h file instead of one
file per variant.
Change-Id: I425654c1c972118aa81c27961246238c2eef782d
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/23683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add FSP option to enable/disable VT-d (Intel Virtualization Technology
for Directed I/O) and VMX (Virtual Machine Extensions), VMX will be
disabled once VT-d got disabled.
Bug=b:73655383
TEST=Build and flash image on meowth board with debug build FSP, in
serial log search for "VMXEnable" and "VtdDiable".
Change-Id: I589590450aa4b9302ee2f9bb7b879a332f50b73e
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fsp revison 7.x.2A.20 also updated MemInfoHob.h to fix SMBIOS Type 17
Offset 15h Speed report incorrectly issue.
BUG=None
TEST=Boot up with meowth platform and run dmidecode to see two dimm
entries under Type 17.
Change-Id: Ie1c4df162e75535ad458709452a76de01e31907e
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25378
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clear EMMC timeout register to avoid EMMC issue according to cannonlake
bios writer guide. _PS0 is not called by kernel when boot source is not
EMMC but kernel still initializes emmc. Add _INI to EMMC,SD asl code to
cover cases that the system doesn't boot from EMMC.
BUG=b:76202699
TEST=Install OS into EMMC
Change-Id: I4eef23f637f781b709696951c5bd825530cc1d11
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/25290
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For some SPI chips (e.g. those with AAI writes), the default OPMENU
definitions don't work well. Thus, provide an option to override the
defaults in the devicetree.
Writing the OPMENU now happens in ramstage instead of the SMM finalize
handler. If you let coreboot call the finalize handler, nothing should
change. If you call the handler from your payload, OTOH, the OPMENU
might have been changed in between, so be careful what you lock.
Change-Id: I9ceaf5b2d11365e21a2bebc9c5def1fcf0be8aad
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add SPD file for sdp hynix_dimm_H5AN8G6NAFR-UHC (ram id: 6).
BUG=b:77290144
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I33503de21c9fc14537c00c092986fd4d2998dace
Signed-off-by: chriszhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
New macros were developed that replace previous way of defining GPIO, with
pin and intention very clear while keeping the table mostly identical to
previous method (there's no pull up or pull down when a GPIO is set as an
output). Change current gardenia table to use the new macros.
BUG=b:72875858
TEST=Build Gardenia.
Change-Id: I402b95374cc5ba01bb961ebcb34d8e465b443c08
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Removed 33KB hole in SSRAM
TEST=build & run
Change-Id: I6851860f878d9a0688975fa855980870d657ee1a
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25391
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the SoC is VT-d capable, write an ACPI DMAR table. The entry for the
GFXVTBAR is only generated if the IGD is enabled.
Change-Id: I8176401dd19aee7ad09a8a145b7a3801fe5b2ae1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX
IOMMU and the general IOMMU respectively. These addresses have to be
configured in MCHBAR registers (maybe, who knows, the blob is undocu-
mented), advertised to FSP and reserved from the OS.
The new devicetree option `ignore_vtd` allows to retain the old beha-
viour (do whatever pre-set UPD values suggest).
We also let FSP set up distinct BDFs for messages originating from the
I/O-APIC and the HPET.
Change-Id: I77f87c385736615c127143760bbd144f97986b37
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Build pl011 to support building vboot on arm platforms.
Change-Id: I1ddc372d558b380065ff944fccb0d84eb37d4213
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
The WP signal to the AP isn't inverted as it is on other platforms, so
it was reporting incorrectly. Change the ACPI table to be active low,
and invert the signal when reporting it to everything else.
BUG=b:74946358
TEST=Boot grunt with battery inserted, WP signals both report 1. Remove
battery, WP_CUR reports 0, WP_BOOT still reports 1.
Change-Id: Ic1369dbda609e34b308af308880449643be6af39
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets PL1 value to ~6W. Here, 8W setting gives
a run-time 6W actual measured power.
Also, this patch sets PL2 value to 15W.
BUG=None
BRANCH=None
TEST=Build and read the MSR 0x610.
Change-Id: I2439a49b9917db0d9b05f333ce1c35003da493f6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/25341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is hopefully more readable.
TEST=Build lenovo/x200 with and without this patch (using make
BUILD_TIMELESS=1), compare build/coreboot.rom, notice no differences.
Change-Id: I079d5353633a3d58ce0e5e616f3fad687a064d65
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23709
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch selects `HAVE_APCI_RESUME` to enable S3 resume. This
has a dependency on EC to store the hash.
BUG=b:72472969
TEST=suspend and resume from S3 should work.
Change-Id: I9de84dfd450936b3bc08e016bec6cf5ae88eab3d
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25390
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copy strrchr from libpayload.
To be used by Cavium's BDK or FDT parsers.
Change-Id: Iab7981c25113ed16f1b8130de4935d30c29d2fa5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Sometimes when bringing up a new board it can take a while until you
have all the peripheral drivers ready. For those cases it is nice to be
able to bitbang certain protocols so that you can already get further in
the boot flow while those drivers are still being worked on. We already
have this support for I2C, but it would be nice to have something for
SPI as well, since without SPI you're not going to boot very far.
This patch adds a couple of helper functions that platforms can use to
implement bit-banging SPI with minimal effort. It also adds a proof of
concept implementation using the RK3399.
Change-Id: Ie3551f51cc9a9f8bf3a47fd5cea6d9c064da8a62
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The <gpio.h> API is supposed to include a gpio_set() function that just
toggles the state of a GPIO already configured as an output, even though
we rarely need it since gpio_output() can already be used to initialze a
GPIO to a default value while configuring it as an output. This function
was forgotten on Rockchip, so this patch adds it now.
Change-Id: I201288139a2870e71f55a7af0d79d4a460b30a0c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
BUG=b:77345148
TEST=Pull power from grunt, verify CMOS power failure is detected.
Reboot and verify that CMOS power failure is not detected.
Change-Id: Idbf0254e197a6d282e618a98bced52ea5a44917f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25468
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change f43adf0 (intel/common/block/cpu: Change post_cpus_init after
BS_DEV RESOURCES) moved post_cpus_init to BS_OS_RESUME for S3
path. This results in BSP timing out waiting for APs to be
parked. This change increases the time out value for APs to be parked
to 250ms. This value was chosen after running suspend-resume stress
test and capturing the maximum time taken for APs to be parked for
100 iterations. Typical values observed were ~150ms. Maximum value
observed was 152ms.
BUG=b:76442753
TEST=Verified for 100 iterations that suspend-resume does not run into
any AP park time out.
Change-Id: Id3e59db4fe7a5a2fb60357b05565bba89be1e00e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
google_chromeec_command() may only write the 1 or 2 bytes to
variable r (4 bytes). However, this api returns 4 bytes data.
To avaid returning the incorrect data, we need to initialize the
local variable.
BUG=b:76442548
BRANCH=none
TEST=write 2 bytes data into the flash, then, read by cbi_get_uint32
Change-Id: I3395c97ab6bfd7882d7728310de8a29041190e76
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25460
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case of all DMI Type 17 to be empty, the strip trailing whitespace
code will have a zero length Part Number entry, which will cause
exception when using (len - 1) where len is zero. Add extra code to
cover this corner case.
BUG=b:76452395
TEST=Boot up fine with meowth platform, without this patch system will
get stuck at "Create SMBIOS type 17".
Change-Id: Id870c983584771dc1b60b1c99e95bbe7c0d25c4c
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25377
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to save the ACPI OpRegion table
address in ASLB, and restore table address upon S3 resume.
Implementation modeled on existing Baytrail code.
Test: boot Windows 10 on google/chell with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: Icd6b514e531eec6e49dbb03eb765144f41c1e31b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to save the ACPI OpRegion table
address in ASLB, and restore table address upon S3 resume.
Implementation modeled on existing Baytrail code.
Test: boot Windows 10 on google/edgar with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: I7c1fbf818510949420f70e93ed4780e94e598508
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Get rid of custom opregion implementation and use drivers/intel/gma/opregion
implementation instead.
Test: boot Windows 10 on google/chell and google/edgar using Tianocore
payload with GOP init, observe Intel graphics driver loaded and functional.
Change-Id: I5f78e9030df12da5369d142dda5c59e576ebcef7
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21703
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
me_progress_rom_values array provides detailed information maps to ME
HFSTS2 register value.
There is a chance that ME status value might be over the size of
me_progress_rom_values.
This commit adds a check before access the array.
BUG=b:77247550
Change-Id: I5de569c62b94b0595d3d3ea254f50e312e8c11a4
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/25425
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new variant of Poppy for the Atlas board.
BUG=b:75454415
TEST=tested on a P0 board. System boots and is mostly
functional, though some peripherals are not ready so there
are no touchpad/touchscreen devices configured yet.
Change-Id: I5a0bccd1bda0134aa51885ac2c6e7bb5b45de924
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change updates devicetree and GPIO configurations to match the
schematics:
1. pcie_rp...[2] is the one being used for wifi, thus, clk_req and
deemphasis_enable for [2] need to be set instead of [0].
2. WLAN power enable, wifi disable and PERST# GPIOs need to be
configured correctly.
BUG=b:76180142
TEST=Verified that wlan0 scan works.
Change-Id: Ic51a94902e2cac3491081ade32079e5b88719f45
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This moves the sandybridge both smm setup and smihandler code to a
common place.
Tested on Thinkpad X220, still boots, resume to and from S3 is fine
so smihandler is still working fine.
Change-Id: I28e2e6ad1e95a9e14462a456726a144ccdc63ec9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This enables ThunderPeak WiFi card on M.2.
TEST=Verify wlan card shows up in lspci
Change-Id: I5b3f871bdc67bfc4ed283b997b2a5698451b2bd2
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/24931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable VMX if supported by CPU and enabled in board devicetree.
Check lock bit unset before enabling VMX.
Change-Id: Ic57eac45e9c65baa4479735c6d70a7eb685f080e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb.
Change-Id: I34e7d750d3f75757a68977ae8d92bfbee1a10af1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
Change-Id: I5aea15511c52d1191babf551feb237f4144683e4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When CONFIG_VBOOT is enabled then the xDCI controller should only be
enabled if the system is in developer mode. This prevents a system
in normal/verified mode from being used as a USB peripheral device
which could potentially be used to access user data.
This change adds a function to return whether xDCI can be enabled
or not, which will be used by the SOCs.
Change-Id: Ie3ee9dd7077c094a01fd857a2e4033a12ce8979b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch disables debug consent in the devicetree. When debug
consent is set to DBC by default, it prevents some clocks from turning
off during S0ix. This blocks S0ix entry.
This patch also enables S0ix from the devicetree.
BUG=b:76163091
TEST=enter S0ix and check if slp_s0 is asserted
Change-Id: I05001a41b13e7784c34fa8f1f773fb94bbdcd01f
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25312
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the NHLT configuration for the max98373 codec to skylake,
taken directly from cannonlake.
This will allow skylake/kabylake boards to use this codec.
Change-Id: Ifb6bf2d31fda25b18d9b1ce2bb721255335d55e4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds a call to heci_reset before attempting to read
ME firmware version. This is important to ensure that both ME and BIOS
are in sync.
BUG=b:76167737
BRANCH=poppy
TEST=Verfied that ME firmware version read does not fail on first boot
after power failure (i.e. removing battery and AC power).
Change-Id: Ib6b39c398d2e1177b087352a4acb8bcf5a9897d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Current emmc tuning parameters for octopus were copied over from other
boards and result in failure to boot from emmc. This change gets rid
of the emmc tuning parameters in devicetree. Once emmc tuning tests
are run for octopus, these parameters can be added back.
BUG=b:75986903
BRANCH=None
TEST=Verified that octopus boots from eMMC without any errors in
depthcharge.
Change-Id: I7ac44a54afd1ecfe355a9654ac8e92133b67637f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch changes the GBB flag configuration to the latest usage in
upstream vboot (as of https://chromium-review.googlesource.com/976660).
Change-Id: I585d662d7de34b4964d028e3d06b4df5665fbe9e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The EC needs to set the PPCM value depending on whether
Turbo is enabled or not, and the values differ between
Broadwell (0, 1) and Skylake (1, 2) platforms.
Change-Id: I662dce54415e685c054ffc00b6afde0f1f7765e2
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The LPC I/O ports for EC communication were not set properly,
causing ectool to fail to read the Index I/O from the EC.
The EC Index I/O is on port 0x380 and the LPC I/O port needs to be
decoded by the PCI device for it to be accessible.
Correct the value for the Librem 13v1, 13v2 and 15v3.
Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change remove work-around code for the power issue of MIPI and
USB cameras on previous board revision. With the work-around code,
PMOF ACPI method cannot turn off MIPI camera. So we need to remove
it.
BUG=b:74214248
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/25337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The code is based on autoport and that for revolve_810g1
Tested:
- CPU i5-3437U
- Slotted DIMM 8GiB
- Onboard USB2 interfaces (wlan slot, wwan slot, camera, smart card)
- Mini pci-e on wlan slot
- On board SDHCI connected to pci-e
- USB3 ports
- USB3 hub on dock (connected to USB3 port 1)
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.13.17-1 within Debian GNU/Linux testing, loaded from
SeaBIOS, or Linux payload (Heads)
Not tested:
- Fingerprint reader on USB2
Not working well:
- EHCI debug on port SSP2,(The USB port on the left, wired to ehci
before OS) it has always-on enabled by default (maybe via EC),
which disturbs FT232H's own power up, requiring a very critical
timing to plug it in for it to work.
Change-Id: I52e549ec18e8aa661a506a16dbc7f83417c0da78
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/25218
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=build
Change-Id: I32d185741ce20a3a82e6895de3026ade52d0bcc8
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
TEST=build
Change-Id: Ie54e310a94f61b8d86c13261937015e3f5a2ab01
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
A change introduced by commit fe4983e5 [1] in order to prevent
re-initialization of the TPM if already set up in verstage
had the wrong logic in the if statement, causing the TPM
to never be initialized if vboot is disabled.
The RESUME_PATH_SAME_AS_BOOT config is enabled by default for
ARCH_X86, resulting in the if statement to always evaluate to
false. Remove that condition from the if statement to allow it
to function as intended.
This patch also enables TPM initialization for FSP 2.0 with
the same conditions.
[1] intel/fsp1_1: Do not re-init TPM in romstage if already setup in verstage
https://review.coreboot.org/#/c/coreboot/+/14106/
Change-Id: Ic43d1aa31a296386c7eab6d997f9b701e9ea0fe5
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23680
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the support for KBL-S MCH and Z270, H270, B250 and
Q250 PCH chips.
BUG=None
BRANCH=None
TEST=Boot with KBL-S CPU and B250/H270 PCHs.
Change-Id: If03abb215f225d648505e05274e2f08ff02cebdc
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/25305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
In an attempt at consolidation, commit 0a203d1 [1] introduced
an additional read/write of the MISC_ENABLE msr, as well a bug
which nullified the setting of Intel SpeedStep by inserting said
read/write calls in between another set of read/write calls to the
same msr. Fix by reverting to previous (simpler) implementation.
[1] soc/intel/skylake: Use CPU common library code
https://review.coreboot.org/19566
Test: boot Linux on Librem13v2, read MISC_ENABLE msr and verify
SpeedStep bit correctly set based on devicetree setting.
Change-Id: Id2ac660bf8ea56d45e8c3f631a586b74106a6cc9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets the PNP config value to PNP_PERF_POWER.
The config values for soc can be found in chip.h
TEST = Build for octopus.
Change-Id: I2239aa70cb708e6e1c06339ca9d517e7eaa198ed
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25310
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Don't write more bytes than the caller requests.
Based on I484b5c1e3809781033d146609a35a9e5e666c8ed.
Change-Id: I336de417c7cd6f35cf84947fc4ae161c15bd93ef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch sets the PNP config value to PNP_PERF_POWER.
The config values for soc can be found in chip.h
TEST = Built and booted glkrvp, verified warm and cold
reboot and suspend resume.
Change-Id: Ia390c0fafe2de64bd9e4ca44e5ed5d904663ae3c
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds a new Kconfig option for mainboard octopus "HAS_TPM"
that auto-selects all TPM related options only if VBOOT_MOCK_SECDATA
is not selected.
BUG=b:76203913
TEST=Compiles fine with mocktpm.
Change-Id: Ib28fc47a70be58cd9a9ec65ce3b1cda68d558437
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25340
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Example output:
AGESA TYPE 17 DMI INFO:
Handle: 1
TotalWidth: 64
DataWidth: 64
MemorySize: 8192
DeviceSet: 0
Speed: 1200
ManufacturerIdCode: 44416
Attributes: 1
ExtSize: 0
ConfigSpeed: 933
MemoryType: 0x1a
FormFactor: 0xd
DeviceLocator: DIMM 0
BankLocator: CHANNEL A
SerialNumber(8): 00000000
PartNumber(20): HMAA51S6AMR6N-UH
CBMEM_ID_MEMINFO:
dimm_size: 0
ddr_type: 0x1a
ddr_frequency: 1200
rank_per_dimm: 1
channel_num: 0
dimm_num: 0
bank_locator: 0
mod_id: 44416
mod_type: 0x1a
bus_width: 64
serial(4): 0000
module_part_number(23): HMAA51S6AMR6N-UH ��@
dimm_size, mod_type, bus_width need to be updated so they return the
correct values. module_part_number is missing a null terminator due to
the AGESA part number being larger than the dimm_info buffer.
Example dmidecode output:
Memory Device
Array Handle: 0x0000
Error Information Handle: Not Provided
Total Width: 8 bits
Data Width: 8 bits
Size: No Module Installed
Form Factor: Unknown
Set: None
Locator: Channel-0-DIMM-0
Bank Locator: BANK 0
Type: DDR4
Type Detail: Synchronous
Speed: 1200 MT/s
Manufacturer: Hynix/Hyundai
Serial Number: 0000
Asset Tag: Not Specified
Part Number: HMAA51S6AMR6N-UH
Rank: 1
Configured Clock Speed: 1200 MT/s
Minimum Voltage: Unknown
Maximum Voltage: Unknown
Configured Voltage: Unknown
To enable the output set CONFIG_DEBUG_RAM_SETUP.
The Kconfig change is required in order to enable
CONFIG_DEBUG_RAM_SETUP, otherwise it's not a valid option.
BUG=b:65403853
TEST=Test output shown above
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5eac00b9400056357915761287770a400b3f9f8b
Reviewed-on: https://review.coreboot.org/25303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
dmidecode used to print
'HMAA51S6AMR6N-UH '
it now prints
'HMAA51S6AMR6N-UH'
BUG=b:65403853
TEST=Verified using dmidecode
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia10ef434a2377e34ae7a8f733c6465c2f8ee8dfa
Reviewed-on: https://review.coreboot.org/25302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets the ACPI FADT flag ACPI_FADT_LOW_POWER_S0
if S0ix is enabled for the platform. This also sets the
FSPUPD to indicate the status of S0ix on the platform.
TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0 flag
is set in FACP table - FADT.Flags[21] bit.
Change-Id: I6214ebb61f25ef8b704e60c8474808493c92e6f6
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25292
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Always report that EC is in RO mode. This is a temporary workaround
for a hardware issue that is causing EC to appear to be in RW mode
when it is not. This change will be reverted once transition is made
to newer hardware.
BUG=b:74215817
BRANCH=master
TEST=Verify meowth can boot to recovery's insert screen.
Change-Id: Ib3705bba0bb1f351da79e599566fbffab94428f3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the config for setting SPD DIMM size to 512 bytes
for KBLRVP8 with DDR4 memory. Configure the DIMM1 memory
SPD data for channel0 and channel1. Set the UserBd UPD to
BOARD_TYPE_DESKTOP for kblrvp8.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I985968d331991884050c3920ec9798cd4cb371c7
Reviewed-on: https://review.coreboot.org/25194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
The VA space needs to be extended to support 48bit, as on Cavium SoCs
the MMIO starts at 1 << 47.
The following changes were done to coreboot and libpayload:
* Use page table lvl 0
* Increase VA bits to 48
* Enable 256TB in MMU controller
* Add additional asserts
Tested on Cavium SoC and two ARM64 Chromebooks.
Change-Id: I89e6a4809b6b725c3945bad7fce82b0dfee7c262
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/24970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Print the wake status bits to the console. The format is kept similar
to Intel's to maintain compatilibity with inspection utilities. Add
relevant wake events from the register to the ELOG. Clear the register
before continuing.
TEST=Inspect console and ELOG for Grunt
BUG=b:75020968
Change-Id: Idc9d12326abb290e4f7a5c60677eb6e057d475b2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
This change defines IFD_CHIPSET as sklkbl to allow ifdtool to set the
right access control bits for SKL/KBL platforms.
BUG=b:76098647
BRANCH=poppy
TEST=Verified that the access control bits on KBL platforms are set correctly.
Change-Id: I7b2131caa06d6a975e703262931ec0ea519a86aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
I2C bus 2 goes to the custom add-in card slot and it was disalbed cuase
it was idle.
Google CFM add-in card is going to use this I2C bus so it needs to be
re-enabled.
BUG=b:73006317
TEST=Tested with add-in card on fizz hardware and verified I2C bus 2 is
working properly.
Change-Id: I2c9b5a9323fd51872e340c35005c4a3432716808
Signed-off-by: Zhongze Hu <frankhu@chromium.org>
Reviewed-on: https://review.coreboot.org/25258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
This creates a bip variant for octopus. Nothing is set in the variant
files here-- everything is picked up from baseboard.
BUG=b:75976864
TEST=None
Change-Id: I7a8ac3d8bb71416f05ef1a605684d92d5902abda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25285
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tools/scripts, like mosys/arc-setup, use int (4 bytes) to
read the sku id. In order to support "-1", we need to use
uint32_t (4 bytes) instead of using uint16_t (2 bytes) data type.
Otherwise, tools/scripts will read 65535 instead of -1.
Another reason to change this is that sku_id can be
supported by ec up to 4 bytes.
BUG=b:73792190
TEST=mosys output "Platform not supported" for -1 sku id
arc-setup read -1 sku id
Change-Id: Ib3baa8419f138abeb412ac09c2e7dc608e3b758b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Audio machine driver will enable/disable clock by making it as
a CCF clock in kernel.
BUG=b:74570989
TEST=cherry-picked https://patchwork.kernel.org/patch/10291875/
on 4.14 kernel
aplay -vv <file>
check register to see clock enabled
kill aplay
check register to see clock disabled
Change-Id: Ia553e55ffb358415067000d2d2d2744322d1c4db
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set up the EC communication a little earlier so we can read the board
ID before programming GPIOS.
BUG=b:73078053
TEST=Build & Boot grunt, board_id() now gets ID correctly
Change-Id: Icf3f598824cfed69fa03ba2bb86503bb3c3699a5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25286
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The following PCI device ID can be included for jefferson peak wifi
devices driver support, and they are:
9df0 for jefferson peak on Cannonlake-LP w/CNVi
A370 for jefferson peak on Cannonlake-H w/CNVi
31dc for jefferson peak on Geminilake w/CNVi
BUG=None
TEST=None
Change-Id: I48886cea5578a302f6ef033cb35df4a38bd64ea8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to the schematic, Octopus boards have WLAN_PE_RST connected to
GPIO_164. This change configures that properly in devicetree.
BUG=None
TEST=None
Change-Id: I2ba4839e036f02c5e0316d08599894879133894a
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25248
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO pad configurations for GPIO68-71 are incorrectly configured as
outputs. This change corrects them to be inputs.
BUG=b:74932341
TEST=None
Change-Id: I319f8a64d83c29ed150316c15a8d429cc7c024f3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25217
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCIe de-emphasis is enabled by default. Thunderpeak Wi-Fi requires
it to be disabled. Therefore allow it to be configured via a
device tree setting.
TEST=On GLKRVP, verify Thunderpeak Wi-Fi card shows up in lspci when
de-emphasis is disabled in device tree.
Change-Id: Iae204768dfe00a638c764644c44c7cda269e73e0
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25185
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO for EEPROM write-protect should be configured early, before
romstage. This change configures that pad earlier. This pad is the same
on the existing Octopus schematics.
BUG=None
TEST=None
Change-Id: Idf296ba6aad75b890afabd6f7c7c51fbaf911214
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We are enabling at the kernel level, but that is triggering an issue
where FSP expects it to be disabled so it forces a cold reboot on
every warm reboot, clearing the ramoops logs. Enabling in BIOS so it
matches what the kernel expects.
This is the same change that were done for eve:
https://review.coreboot.org/#/c/22449/
BUG=None
BRANCH=None
TEST=echo PANIC > /sys/kernel/debug/provoke-crash/DIRECT
check for /dev/pstore/console-ramoops
Change-Id: Icd0bd01f5aee4c89f503eebba0808a1f3059e739
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The GPIO programming of configure_stoneyridge_UART() can be done by the early
GPIO table, AOAC enabling was already removed. So configure_stoneyridge_uart()
became redundant. Remove procedure configure_stoneyridge_uart().
BUG=b:74258015
TEST=Build and boot kahlee, observing serial output does not changes from
previous serial output.
Change-Id: Ie67051d7b90fa294090f6bfc518c6c074d98cc98
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25192
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO_149 is used as ESPI clock feedback and configuring it as a GPO
results in EC communication failure. This change removes the
configuration of GPIO_149 as GPO in ramstage so that it remains
configured for ESPI (as it was when AP came out of reset).
BUG=b:75348718
Change-Id: Ie4f21b12fae027cdba54ce147e6d1a88ee854792
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Call sb_spibase() early so that it will set up the SPI base address.
This is another step to moving AGESA calls out of the bootblock.
BUG=b:74427893
BRANCH=master
TEST=Build and boot Grunt.
Change-Id: I665d32f3acb0046eb6abbd363735561f0372f2a0
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
glk has different memory profile values than apl. Therefore, a
translation is required to correctly set the proper profile value
depending on what SoC (and therefore FSP) is being used. Based on
SOC_INTEL_GLK Kconfig value use different profiles.
BUG=b:74932341
Change-Id: I6ea84d3339caf666aea5034ab8f0287bd1915e06
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25249
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It was required for all cores use the same CAR teardown function
(exit_car.S and gcccar.inc). AGESA has already been modified to do the
AP to do the call out. Create assembly code to call chipset_teardown_car
and then enter an endless loop with halt instruction. Then create the
call out that will call this new assembly code.
BUG=b:70338633
AGESA COMMIT=3313d277
TEST=Created a debug version of AGESA that would print the returned
status of HALT_THIS_AP. Build code without the fix, see the return.
Build code with the fix, see that there's no return.
Change-Id: I05ee405812211d93dfdbdc5ee7d9978c2eb585e1
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/24999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
AGESA.bin was updated in the binary repo, so update the submodule pointer.
Among other changes, this added a callback "AGESA_HALT_THIS_AP", which
requires updated header files.
BUG=b:70338633
TEST=build kahlee.
Change-Id: I5a07f1c539d00aed34cfe45d6d7ef60c1dc56566
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25183
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Devices that need to have their AOAC register enabled do have a delay before
they become available. Currently each device has their own wait loop. Create
a procedure that initializes all AOAC devices in a table and wait for all
AOAC to become alive, then call this new procedure before the call to
initialize the UART. Then change all procedures that initialize some AOAC by
moving the devices to the table and removing AOAC initialization code.
BUG=b:74416098
TEST=Build and boot kahlee checking that UART is sending debug messages out.
Change-Id: I359791c2a332629aa991f2f17a67e94726a21eb5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
PcieRpHotPlug in apollolake UPD is default enabled. This change adds a
config option to enable hotplug only if explicitly requested by
mainboard. This changes the default behavior on all apollolake boards
to have hotplug disabled.
BUG=b:74633273
BRANCH=reef,coral
Change-Id: I572c054d31aaf5d43a79c4b1773ec9356da48d9d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change uses an array pcie_rp_clkreq_pin for accepting CLKREQ#
from mainboards instead of defining a separate property for each root
port. This allows us to use memcpy to copy the entire array into FSP
params as well as new properties for PCIe root ports can be added as
arrays in future CLs.
BUG=b:74633273
BRANCH=reef,coral
Change-Id: Ifa05f1e38fcfd95063ec327712e472cdbd12dbb7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1) Set the critical temperature threshold to 100C to match changes
on other boards. This is intended to reduce DPTF-initiated thermal
shutdowns before it has had a chance to react.
2) Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
BUG=b:67459049
BRANCH=eve
TEST=manual performance/power testing on Eve hardware
Change-Id: Ib660dcb25422fea0aa692fac5ba65b49808965ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Touchscreen power enable for Nami has moved from GBB_C22 to GPP_B4 in
the latest schematics.
BUG=b:74347464
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I3b1794d44f25c0d42d082d63b9e3ec3dfcef7528
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25154
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Call function sb_acpi_mmio_decode() from bootblock_fch_early_init().
This enables decoding of the FCH ACPI MMIO regions 0xfed80000 -
0xfed81fff. This is another step to moving AGESA out of the bootblock
for StoneyRidge
BUG=b:74586747
BRANCH=master
TEST=Build and boot on Grunt.
Change-Id: I8cf329e5cd2002b225742fefa5c1ddd2598de674
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25161
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to generate ACPI OpRegion, save the
table address in ASLB, and restore table address upon S3 resume.
Implementation largely based on existing Haswell/Lynxpoint code.
Test: boot Windows 10 on google/lulu with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: I024f4f0784df3cbbb9977692e9ef0ff9c3552725
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The cannonlake FSP enables PchLockDownRtcMemoryLock by default, but we
need this memory to be writable. We normally over-ride this in the
SoC chip init code, so we'll do the same on cannonlake.
BUG=b:71722386
BRANCH=none
TEST=Filled /dev/nvram with 0xff and 0x00 bytes to verify we can flip
all the bits.
Change-Id: I7cdd4abc2b3795d7dd82236fbe3c112428ee882b
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Fix the IRQ configuration: it must be level-sensitive not edge-sensitive
(and match the GPIO configuration).
BUG=b:71986991
BRANCH=none
TEST=on Meowth, /proc/interrupts shows 'IO-APIC 46-fasteoi chromeos-ec'
then run 'ectool --name=cros_fp fpmode fingerup' and see the number of
interrupts incrementing and the MKBP event happening.
Change-Id: Iba8cff21d637fe6bf4ef5152fc01aaf98906477d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/25110
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable System Agent dynamic frequency support by default.
BUG=None
TEST=Build and flash with debug version FSP, check SaGv in serial print
to be set to "4".
Change-Id: I7dd29db206b06e600407bb0b1d0bc7530f4ac93e
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25093
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SaGv(Sytem Agent Dynamic Frequency) have four settings, disabled,
disabled but running at fixed lower frequency, disabled but running at
fixed middle frquency, disabled but running at fixed high frequency and
totally enabled.
BUG=None.
Change-Id: Ib5fb648179e7889aaa64d91e6cf7a7a7503f4225
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In preparation for moving AGESA calls out of the bootblock:
* Add sb_tpm_decode to enable FCH decoding of TPM 1.2 regions and Legacy
TPM IO 0x7f-0x7e and 0xef-0xee
* Modify sb_tpm_decode_spi to additionally call sb_tpm_decode.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt (with other changes
to call code not committed at this time)
Change-Id: I0e2399e113c765393209dd11fd835fc758cf3029
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to generate ACPI OpRegion, save the
table address in ASLB, and restore table address upon S3 resume.
Implementation largely based on existing Broadwell code.
Test: boot Windows 10 on google/squawks with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: Iab15e1de2bb7d8fbec2e8705a621cfca0f255d4b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Most Intel platforms use separate registers for software-based
SMI (0xe0) and SCI (0xe8), but Atom-based platforms use a single
combined register (0xe0) for both. Adjust opregion implementation
to use the correct register for Atom-based platforms.
Test: Boot Windows on Atom-based ChromeOS device with Tianocore
payload and non-VBIOS graphics init; observe Intel display
driver loaded correctly and internal display not blank.
(requires additional change for Atom platforms to select
CONFIG_INTEL_GMA_SWSMISCI)
Change-Id: I636986226ff951dae637dca5bc3ad0e023d94243
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
ACPI ID for coreboot is now "BOOT" according to CL:18521.
BUG=none
BRANCH=master
TEST=none
Change-Id: I802ce284001b186f6cd8839b8c303d49f42b4d38
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/25042
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since nami proto did not have any external pull on MEM_CONFIG_4, use a
weak internal pull down before reading it.
BUG=b:74420123
TEST=Verified that the value read for MEM_CONFIG_4 is correct on nami.
Change-Id: I45989d2ca35b863f391baba9e2f2e602033217d4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The current lpddr4 skus entries do not match the RAMID table in the
schematic. This commit updates that so they are consistent. Thankfully,
the values are the same as for glkrvp, so I just copied from there.
BUG=b:74392818
TEST=None
Change-Id: I2e63ea0b27ef58038e5a37949c31a808989c98c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The following gpios are no longer needed and are now configured as
no-connects : GPP_C6, GPP_H4, GPP_H5
BUG=b:74406599
BRANCH=master
TEST=none
Change-Id: I55769336195db0e57dfbaf5b5770e15050138341
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make sure that fields that are not updated in
variant_memory_params keep a default value of 0.
In particular, use_sec_spd is intended to have a default value of
0 on all platforms. Without this patch, a random value is used
and all boards (except nami) get stuck on boot.
BRANCH=poppy
BUG=b:74439917
TEST=Nautilus and poppy can boot, and do not get stuck at
"CBFS: 'sec-spd.bin' not found."
Change-Id: I06c6511625de930903ae13788bdcd27667a17886
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/25101
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
we had disabled software sync for bringup - we now have enough
functionality in place to turn on software sync.
Change-Id: Ib7f5a24ed8a47cb44b3f505e3cd49e0cb6931dc0
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23630
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per PCH BWG 2.5.16, set up LPC IO Enables PCR[DMI] + 2774h bit
[15:0] to the same value program in LPC PCI offset 82h. Also this
cycle decoding is only allowed to set when SRLOCK is not set.
Hence move the required programming from lpc.c to pch.c.
Also only enable COM port ranges if CONFIG_DRIVERS_UART_8250IO
Kconfig is selected.
Change-Id: Ie706735492a450baa653d8a8bb74c6e42f5150b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
By default all Intel platform has enable IO decode range for COMA if
CONFIG_DRIVERS_UART_8250IO is selected.
With this patch, COMB will get enable based on
CONFIG_SOC_INTEL_COMMON_BLOCK_LPC_COMB_ENABLE Kconfig selection.
Also make lpc_enable_fixed_io_ranges() function returns Enabled I/O bits to avoid
an additional pci configuration read to get the same data.
Change-Id: I884dbcc8a37cf8551001d0ca61910c986b903ebc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change SECONDARY_SPD_SOURCES to SEC_SPD_SOURCES as that is what the
spd target expects.
TEST=Verified that sec-spd.bin is present in coreboot.rom
Change-Id: I4299df1eb9009095ef899c5b83823750dfc715d8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Prints the timestamp name and value to the debug console if enabled
in Kconfig.
Change-Id: Ie6e6a4877fefec45fb987ceae7d42de6ce768159
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
In preparation for moving AGESA calls out of bootblock:
Add function to enable the four stoneyridge I2C engines.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt (with other changes
to call code not committed at this time)
Change-Id: Icb55c49cf56c65a9c2e1838cff1ed5afc04e1826
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25026
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In preparation for moving AGESA calls out of bootblock:
* Add definitions for needed registers in southbridge.h
* Add function to enable AMD FCH ACPI MMIO regions 0xfed80000 to
0xfed81ffff. Will be called by a later commit.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build boot Grunt (with other changes
to call code not committed at this time)
Change-Id: If26efa6c6f5b562ba898e7d9da4827833310dc26
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25025
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FSP can only output its traces when the HSUART PCI device is
available.
- Move the hiding to after last FSP call.
- Adapt coreboot PCI enumeration to keep the legacy configuration.
With UART configured as legacy Linux will not re-enumerate it but detects
it as legacy (ttyS0 instead of ttyS4).
Change-Id: Id8801e178ffd8eeee78ece07da7bd6b8dbd88538
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
GPIO 40 isn't currently being used, so set it to be an input.
BUG=b:73387647
TEST=Build & boot grunt
Change-Id: I5a04cbab1276cd20e7f9c7576e8111089dd2b155
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Bayhub part is not used on proto with board_id 0, so disable it.
BUG=b:74248569
TEST=Build & boot Grunt. Bayhub part is disabled.
Change-Id: I635356d41bab637726594d403d66dde730f12256
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Update build so that we can get the board ID in bootblock.
BUG=b:74248569
TEST=build and boot grunt with follow-on patch.
Bayhub part is disabled.
Change-Id: I6353bcb4abcef4e8dc2b625082e33b73525c8525
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since the timeout in bsp_do_flight_plan is bumped up to 1 second, this
change adds a print to indicate the amount of time it takes for all the
APs to check-in.
TEST=Verified on Nami that it prints:
"bsp_do_flight_plan done after 395 msecs."
Change-Id: I4c8380e94305ed58453ed18b341b3b923949d7a8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX
IOMMU and the general IOMMU respectively. These addresses have to be
configured in MCHBAR registers and reserved from the OS.
GFXVTBAR/VTVC0BAR policy registers set to be consistent with
proprietary vendor firmwares on hardware of same platform
(2 different vendor firmwares compared, found to be identical).
Change-Id: Ib8f2fed9ae08491779e76f7d1ddc1bd3eed45ac7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24983
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This #define tells superio.asl to add a "PNP0501" "Plug and Play
16550A-compatible COM port" entry to kahlee's ACPI tables.
The EC on kahlee boards do not provide a "Serial Port 1" that should
be exposed via ACPI to the OS. In fact, this entry confuses the
kernel and in some cases can cause it to try to redirect output to a
non existing port.
BUG=b:74200887
TEST=Deploy to grunt. Boot kernel with SERIAL_PORT_DFNS undefined and
"earlycon=uart,mmio32,0xfedc6000,115200,48000000" on the kernel
command line, and with an image with serial console enabled.
=> System boots with (kernel) serial console enabled, starting from
0.00 (earlycon), with no gaps in its output, and serial console
also allows logging in.
Change-Id: I0eaed9b4461bb6a6c1aa4ce97752f588d4322b35
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Move call to __gspi_cs_change() in gspi_ctrlr_setup() to after
initialization of cs polarity since it requires polarity to be
set to work properly. Failure to do so confuses cr50.
BUG=b:70628116
BRANCH=chromeos-2016.05
TEST='emerge-meowth coreboot' and verify on scope that chip select
polarity is correct for the first transaction.
Change-Id: I20b4f584663477d751a07889bccc865efbf9c469
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
coreboot's PCI resource allocator doesn't assign BAR1 for
Braswell's LPE device because it doesn't exist, but is
required by Windows drivers for the device to function.
Manually add the required resource via the existing
lpe_read_resources function, and marked it as IORESOURCE_STORED
so pci_dev_set_resources ignores it.
TEST: boot Windows 10 on google/edgar, observe that memory resources
are properly assigned to LPE driver for BAR1 and no error reported.
Change-Id: Iaa68319da5fb999fe8d73792eaee692cce60c8a2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add timestamps before and after the vBIOS load and after the vBIOS
run. This lets us see exactly how long it took to load it from the
ROM chip, and how long it takes to run.
BUG=b:64549506
TEST=Build & boot Grunt, see vBIOS load & initialization times.
Change-Id: I878ba653eb086ad6c6614aa08a6d3fe216a9323e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25018
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hardware updates have suggested we need to configure the K&D panel's
power sequence in software, not in hardware. Without this change, K&D
panels will no longer power on correctly and will instead display a
black screen.
Per K&D's suggestion, we tweak these two commands. From the little HW
docs I have, this looks like it's:
(Address 0xB7, Value 0x02) -> set BC_CTRL=bit(1) (Back light control) to
1
(Address 0xF1, Value 0x22) -> change GPO2_SEL=bits(0:3) from
MIPI_TE(0001b) to BC_CTRL (0010b)
BRANCH=scarlet
BUG=b:73133861
TEST=KD display with and without HW fix on Scarlet
Change-Id: Ia076a378b10417dd9891746f9bc1086360a0f6e6
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-on: https://review.coreboot.org/25023
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Looks like there's a typo in the GPIO state table we print as part of
assembling the coreboot tables. Of course, high GPIOs are represented as
1 and low GPIOs as 0. Fix this display bug.
Change-Id: I59b4d49955c13f920576dd09f463e2d399ab64e0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25022
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the SoC is VT-d capable, write an ACPI DMAR table. The entry for the
GFXVTBAR is only generated if the IGD is enabled.
Change-Id: Ib354337d47b27d18c3b79b5de3b4fa100b59c8fc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Allows eMMC in PCI mode to be seen/used by Windows.
Test: boot Windows installer on google/edgar, observe internal
eMMC storage available for installation when eMMC in PCI (vs ACPI) mode.
Change-Id: I4272c198e5e675f451a1f4de5d46e3cd96371446
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch configures the gpios for all the gpio communites.
Change-Id: Ibc16edd96f4ef6d55f3a99b195bf4920929b1578
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Per vendor datasheet, corrected linkfreq of imx258 as
{633600000, 320000000}
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: Ie5beed44c15e26b9f82cb305a91b8ff90a9ea867
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-on: https://review.coreboot.org/24990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We want to report the board SKU via the SMBIOS tables. Add support for
this, obtaining the ID itself from the EC.
BUG=b:74175244
BRANCH=none
TEST=manually on grunt with another CL:
mosys platform sku
0
Change-Id: I9e08d64df3f89d3703de047dd9ec8e1717e6b212
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
File soc/amd/stoneyridge/sm.c has a CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
that's not used at all and has no control. It's also not used in the
build process. Remove the define from sm.c, create a true Kconfig
definition and use it to define if power should be restored after a power
failure/recovery.
BUG=b:72873003
TEST=Build kahlee. Use serial output to check what is being programmed
to RTC shadow. Build with and without selecting the Kconfig parameter.
Then remove serial output and leave the parameter unselected (always S5
at power recovery).
Change-Id: Iec82cb68cf1e2a820e610f12d8620488662232aa
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The LPEA device memory resources, required by Windows drivers,
were not being set. Allocate required resources per Inte'sl CHT
Tianocore reference code.
Test: boot Windows on google/edgar, observe LPEA device working properly.
Change-Id: Ic3ecfc2ddade7d76dbaa95ffdd82599c3bcf35da
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
As per the latest schematics, this change configures GPP_B0 as wake
source for WLAN.
BUG=NONE
BRANCH=master
TEST=emerge-nautilus coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I72b940452cfbbe471279ef117a868a8ae0b65b8b
Reviewed-on: https://review.coreboot.org/23526
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is done by overriding the weak functions from smbios.c
Some values are hardcoded as they are characteristics of the
Tagada system. Other are retrieved from the BMC through the
bmcinfo interface.
Change-Id: I9b08660c6677864f5c96c66002b35bd05a366053
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23843
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add more information on baseboard as described in SMBIOS Reference
Specification 3.1.1.
Change-Id: I9fe1c4fe70c66f8a7fcc75b93672421ae808bf1b
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
